ANTUMBRA
DIST
BUILDING INSTRUCTIONS
PCB V1.2
01. BUILD NOTES
Before you start building look through the build manual so that you’ll be familiar with the building process and you won’t run into any surprises!
471
102
471
00 01 02 03 04
02. BUILD
00. Orient the PCB as seen on the left
01. Solder the two TL071s in place
(oriented to the top)
02. Solder the two 1n5819 diodes
Look out for their orientation!
03. Solder the single 470r resistor
This is for the jack LEDs
04. Solder the single 1k resistor
472
102
471
472
102
471
103
103
103
103
105
105
103
103
105
105
105
105
103
103
105
105
02. BUILD
05. Solder the single 4.7k resistor
06. Solder the two 10k resistors
07. Solder the single 30k resistor
08. Solder the five 1M resistors
09. Solder the single 10pF capacitor 472
102
471
303
472
105
102
471
303
472
105
303
471
05 06 07 08 09
105
105
103
103
105
105
105
105
103
103
105
105
105
105
103
103
105
105
105
105
103
103
105
105
105
105
103
103
105
105
472
105
102
471
303
472
105
102
471
303
472
105
102
471
303
472
105
102
471
303
472
105
102
471
303
02. BUILD
10. Solder the three 1nF capacitors
11. Solder the single 10nF capacitor
12. Solder the single 47nF capacitor
13. Solder the three 100nF capacitors
14. Solder the two 1uF electrolytic capacitors
Look out for their orientation! Their shape has to match up with the silkscreen.
10 11 12 13 14
105
105
103
103
105
105
105
105
103
103
105
105
105
105
103
103
105
105
472
105
102
471
303
472
105
102
471
303
472
105
102
471
303
15 16 17 18 19
02. BUILD
15. Solder the two 10uF electrolytic capacitors
Look out for their orientation!
16. Solder the two diodes for mode A.
The type of these diodes are optional, you can use whatever SMD/TH diodes (even LEDs) you want, they all have different flavors, recommended is the 1n270 germanium diodes. (Experimenting is encouraged)
Look out for their orientation!
17. Solder the two diodes for mode B.
Same applies here as for the previous diodes.
18. Flip the board!
19. Solder the 2x5 pin power header
20 21
105
105
103
103
105
105
105
105
103
103
105
105
105
105
103
103
105
105
472
105
102
471
303
472
105
102
471
303
472
105
102
471
303
02. BUILD
20. Solder the 1x3 pin header for the jack lights switch
21. Solder the two SMD LEDs
Look out for their orientation! The marking should be as on the illustration.
22. Flip the board back!
DO NOT SOLDER YET!
23. Place the two jacks
24. Place the two switches
22 23 24
105
105
103
103
105
105
105
105
103
103
105
105
105
105
103
103
105
105
472
105
102
471
303
472
105
102
471
303
472
105
102
471
303
25 26 27
02. BUILD
25. Place the A100k pot
26. Place the A1M pot
27. Place the A10k pot
Now put on the front panel and tighten the nuts on the jacks and pots. Align them in the holes as you like. Solder!
You are done with building! Congratulations!
DIST is designed by David Szebenyi under Antumbra.
It is based on the MXR Distortion+ / Hexinverter
Batteryacid v1.0
www.antumbra.eu
Manual by David Szebenyi ( www.aman.hu
)
2019 • All rights reserved!
