Dynamite DYN4064 Operation Manual
Add to My manuals20 Pages
Dynamite DYN4064 is a versatile battery charger that handles Ni-Cd, Ni-MH, Li-Po, Li-Fe, and Pb batteries. It features a built-in balance port to monitor and balance 1S to 6S lithium batteries during charging, eliminating the need for an external balancer. With adjustable charge and discharge rates, it offers precise control over the charging process.
advertisement
PassPort Ultra aC/DC Charger CyCler oPeration ManUal www.DynaMiterC.CoM
table of Contents
Introduction ............................................................2
Specifications ...........................................................2
Features ....................................................................3
Available Charge Cords and Adapters ..............3
Available Balance Adapters ..................................4
Input Power Connection ......................................5
Charge Mode ..........................................................5
Discharge Mode .....................................................5
Discharge/Charge Cycle Mode ...........................5
Operating Instructions ..........................................5
User Setup Menu ...................................................6
Ni-MH and Ni-Cd Charge Mode .......................7
Ni-MH Discharge Mode .......................................8
Ni-MH Discharge/Charge Cycle Mode .............9
Li-Ion, Li-Po and Li-Fe Charge Mode .............. 10
Li-Ion/Poly Balance Charge Mode ................... 12
Li-Ion/Poly Discharge Mode ............................. 13
Pb Charge Mode ................................................. 14
Warning Information .......................................... 15
Safety Precautions ............................................... 16
Warranty Period ................................................. 16
Limited Warranty ................................................ 16
Damage Limits ..................................................... 17
Safety Precautions ............................................... 17
Questions, Assistance, and Repairs ................. 17
Inspection or Repairs ......................................... 17
Warranty Inspection and Repairs .................... 17
Non-Warranty Repairs ...................................... 18
CE Compliance Information for the European Union .............................. 19
Declaration of Conformity ............................... 19
introduction
Thank you for purchasing the Dynamite ®
Passport ™ Ultra AC/DC Peak Detection
Charger/Cycler. The Passport line of chargers are high performance battery management chargers that can improve the reliability and life of most battery packs.
The Passport Ultra has built-in balance ports to monitor and balance 1S to 6S lithium battery packs during the charge process. The LCD display allows you to view the charge indicator, charge time, current, voltage and unbalanced voltage.
It also charges 1- to 14-cell Ni-Cd and Ni-MH packs.
The discharge and cycling features allow unsurpassed battery conditioning and provides battery performance details to allow you to determine the quality of your batteries and improve their performance.
Be sure to read the entire manual to become familiar with the features of the charger. Failure to understand the features of the charger can cause serious damage to the charger, battery or cause serious injury and damage to personal properly. never leave the charger unattended during use.
specifications
Input: AC 100 to 240V DC 11 to 18V
Battery Type: Ni-Cd/Ni-MH/Li-Po/Li-Fe/Pb
Battery Cell: Ni-Cd/Ni-MH; 1 to 14-Cell
(1.2 to 16.8V)
Li-Po; 1S to 6S (3.7~22.2V)
Li-Fe; 1S to 6S (3.2~19.2V)
Pb; 2V, 6V or 12V
Charge Rate: 0.1A ~ 8.0A (0.1A Per gradation)
Discharge Rate: 0.1A ~ 5.0A (0.1A Per gradation)
Charging Capacity: 1 to 9900mAh
Safety Timer: 10 to 720 minutes or OFF
Trickle Charge Rate: 0.05 to 0.2A or OFF
Peak Sensitivity (-ΔV): 0~15mV
2 www.DynamiteRC.com
Dynamite Ultra AC/DC Charger/Cycler
Features available Charge Cords and adapters
• 4-in-1, 16-bit microchip CPU controller.
• Built-in system temperature protection with additional battery temperature sensor for added safety.
• Convenient AC or DC input low voltage 10-
11V option.
• Integrated, internal balancer for Li-Po and
Li-Fe balance charging with no need for an externally attached balancer.
• Adjustable negative delta* voltage for precise peak charging.
• Cycling function
• Automatic accidental reverse input and output protection.
• Memory functions for charging and discharging parameters.
• Durable, compact and portable design with an aluminum casing and plastic end caps.
• Large 2-line, 16-character dot matrix LCD display.
• Removable AC and DC plug sockets.
• Universal banana-type output terminal.
• 10-tone selectable beep function with volume control.
• Built-in cooling fan.
• Discharge and cycling functions provide battery conditioning and useful data of the battery’s capacity, average voltage and cell balancing.
The Passport Ultra includes the Deans Ultra style charge cord (DYN5006). Dynamite offers charge cords and adapters for all your battery charging requirements. See the list below to order additional connectors.
DYN4003
Receiver Pack Charger Adapter
DYN5000
Charge Adapter Tamiya Female: Deans Male
* Delta voltage: When charging a battery, the voltage will continue to increase until the battery reaches its peak voltage. After it reaches this point, the voltage will begin to drop. This voltage drop is referred to as the
“Delta Voltage.” The sensitivity of this voltage drop can be adjusted for precise charging of your battery pack.
DYN5001
Charge Adapter Tamiya Female: EC3 Female
DYN5002
Charge Adapter Tamiya Female: EC5 Female
Dynamite Ultra AC/DC Charger/Cycler www.DynamiteRC.com 3
DYN5003
Charge Adapt Tamiya Female: Losi Micro
DYN5008
Charge Adapter Banana: EC5 Female
DYN5004
Charge Adapt Tamiya Female to Losi Mini
DYN5005
Charge Adapt Banana to Tamiya Male
DYN5010
12V DC Power Adapter with Cig Plug
available Balance adapters
You may also purchase adapters to adapt
Thunder Power and Losi balance plugs to fit the
Dynamite balance charge sockets.
DYN5012
Adapter Cables-THP BAT-DYN
Balancer, 2–6S
DYN5011
Adapter Cables-LOS BAT-DYN
Balancer, 2–6S
DYN5006
Charge Adapter Banana: Deans Ultra Male
DYN5007
Charge Adapter Banana: EC3 Female
4 www.DynamiteRC.com
Dynamite Ultra AC/DC Charger/Cycler
input Power Connection
NOTE: Do not connect both AC and DC input power types to the charger simultaneously or damage to the charger may occur.
aC Voltage
E. The built-in cooling fan will automatically engage during charge and discharge functions.
F. Press the START button to return to the previous menu after charging.
G. Press and hold the START button for 3 seconds to restart the charging process. This same process is used to start the discharge and cycling modes.
Connect the 100–240 AC input power cord to the appropriate power receptacle.
DC Voltage
Discharge Mode
Connect the red alligator clip to the positive (+) terminal of a 11–18-volt DC power supply or battery. Connect the black alligator clip to the negative (-) terminal.
Charge output Battery Connection
Choose the appropriate charge cord to match your battery pack and connect the positive (red) lead to the positive (+) output terminal. Connect the negative (black) lead to the negative (-) output terminal.
Charge Mode
A. Set the current rate before charging.
Adjustable charge rates from 0.1–8A.
(Current rates can be adjusted by pressing the START button during charging.)
B. See the table below to select the charge rate for Ni-Cd and Ni-MH battery packs.
We recommend that you charge 1800mAh receiver packs at 1.8A(1C).
Battery Capacity Charge Rate Charge Time
600mAh 0.6A 60–80 Min.
1300mAh 1A 78–94 Min.
1800mAh
3300mAh
2A
5A
54–65 Min.
40–48 Min.
C. It is normal for the current rate to drop to
0 then resume during Ni-MH and Ni-Cd charging.
D. A completely discharged Li-Po or Li-Fe battery pack can be fully recharged in approximately 2–3 hours with charge rate at
1C.
A. The discharge rate can be adjusted from
0.1–5A. Reset the current rate by pressing the START button during discharge.
B. When discharging Ni-MH and Ni-Cd batteries, the minimum discharge voltage should not be set lower than .8 volts/cell
(e.g. the cutoff voltage for a 6-cell pack is
4.8V (.8*6)).
Discharge/Charge Cycle Mode
A. Set three parameters: discharge current, discharge voltage and charge current.
B. Press and hold the START button for 3 seconds to start.
NOTE: This mode is only suitable for Ni-Cd or
Ni-MH battery, and could be set to 10 cycles
(max).
operating instructions
A. Press the MODE button to change from the main menu to the setting menu. Rotating the dial in the main menu lists all options available for the battery chemistry shown on the screen. Rotating the dial while in the settings menu lists menus that allow changes to the chargers functionality unrelated to the battery type.
B. Press the START button to change the selected menu.
C. Press START to confirm the option. Press
STOP to clear settings.
D. Press and hold the START button for 3 seconds to charge/discharge.
Dynamite Ultra AC/DC Charger/Cycler www.DynamiteRC.com 5
User setup Menu
NOTE: Screen samples are shown in the order in which they appear when the dial is rotated in a clockwise direction.
Batt Temp Cutoff
ON 50°C
User Setup Mode
Type NiMH Batt
1. Select Battery Type
Press the MODE button until the User Setup mode appears. Scroll clockwise to view the following screens. Press the START dial to change values on each screen while flashing.
Press the START button to accept settings.
5. Adjust Max Charge Temperature and change
Celsius to Fahrenheit
As a safety feature, place temperature probe securely onto battery pack to allow temperature override.
Cycle Charge
Delay 1min
6. Adjust Charge/Discharge Delay Time
Li-Ion/Poly
V-Type 3.7V
NiMH/Nicd/Pb
Trickle 100mA
2. Select Li-Ion/Poly Voltage
Use this screen to select the Li-Ion/Poly charge cutoff voltage.
7. Adjust Trickle Charge Current
NiMH Sensitivity
D.Peak 3mV/Cell
Safety Timer
ON 720min
8. Adjust Max Charge Time
3. Adjust Ni-MH Charge Sensitivity
The Ni-MH Sensitivity option allows the adjustment of the Ni-MH negative delta voltage cutoff/cell.
Capacity Cut Off
ON 9900 mAh
9. Adjust Max Charge Capacity
Nicd Sensitivity
D.Peak 5mV/Cell
4. Adjust Ni-Cd Charge Sensitivity
The Ni-Cd Sensitivity option allows adjustment of the Ni-Cd negative delta voltage cutoff/cell.
6 www.DynamiteRC.com
Dynamite Ultra AC/DC Charger/Cycler
ni-Mh and ni-Cd Charge Mode
Key Beep ON
Music 01 NiMH Charge
4.0A
10. a) Set Operating Beep Sound (On/Off) or b) Select Music
Volume Adjust
100%
Message during ni-Mh Charging
While in the User Setup mode, press the dial to change to Ni-MH battery charging. Press the dial again to confirm changes.
11. Adjust Volume
NiMH 000 : 01 : 0001
Chg 0.10A 7.62V
Input Volt Low
Cut Off 11.0V
12. Set Detecting Input Low Voltage
Back Light
Brightness 100%
See the status by turning switch to left/right.
Press the MODE button to adjust the charge current. Press the START dial and adjust the current rate to the appropriate rating.
Press and hold the dial for 3 seconds to activate charge. The charge status and other settings can be monitored by rotating the dial during fast charge.
13. Adjust Background Brightness
NiMH Sensitivity
D.Peak 3mV/Cell
Load Default
YES/NO ?
1. Ni-MH Charge Sensitivity
To reset to factory recommended sensitivity, see Load Default and select “Yes.”
14. To reset the charger to Initial Setting
Peak Voltage
9.07V
2. Battery Pack Peak Voltage
Dynamite Ultra AC/DC Charger/Cycler www.DynamiteRC.com 7
Input 13.01V
System Temp 36°C
3. Input Voltage/System Temperature
Bat Temp
29°C
4. Battery Temperature
Batt Temp Cutoff
ON 50°C
5. Max Charge Temperature
Safety Timer
ON 720min
6. Max Charge Time
Capacity Cut Off
ON 9900 mAh
7. Max Charge Capacity
Cycle Charge
Delay 1min
8. Charge/Discharge Delay Time
Message after ni-Mh Charging
END 058 : 08 : 3188
Chg 0.01A 8.08V
See the status by turning switch to left/right.
Peak Voltage
9.07V
1. Battery Peak Voltage
Bat Temp
29°C
2. Battery Temperature
ni-Mh Discharge Mode
NiMH Discharge
1.0A 6.0V
notes regarding Discharging
Discharging/cycling Ni-MH and Ni-Cd packs can increase capacity and rejuvenate neglected batteries. Discharge capacity and average pack voltage will allow you to compare batteries to choose the pack with the best performance to maximize run time and power.
Press the mode button once Ni-MH is selected and rotate the dial until the Discharging screen appears. Press the dial to select discharge current rate and cutoff voltage.
8 www.DynamiteRC.com
Dynamite Ultra AC/DC Charger/Cycler
Message during ni-Mh Discharging
Press and hold the START button for 3 seconds to begin discharging.
NOTE: Discharge voltage rates are per pack, not per cell. Do not choose a discharge cutoff voltage below .8V/cell or damage to the battery may occur.
NiMH 000 : 01 : 0001
DIS 0.10A 7.62V
ni-Mh Discharge/Charge
Cycle Mode
NiMH Dhg>Chg 01
1.0A/6.0V ->4.0A
The screen above is displayed when the charger is set to charge after the discharge period.
See the status by turning switch to left/right.
NiMH Chg>Dhg 01
4.0A->1.0A/6.0V
Input 13.01V
System Temp 36°C
1. Input Voltage/System Temperature
The above screen is displayed when the charger is set to discharge after charging.
Message during ni-Mh Discharging/
Charging Cycle
Bat Temp
29°C
NiMH 000 : 01 : 0001
D>C 0.10A 7.62V
2. Battery Temperature The screen above shows discharge then charge status.
Batt Temp Cutoff
ON 50°C NiMH 000 : 01 : 0001
C>D 0.10A 7.84V
3. Max Discharge Temperature
This screen is displayed during the charge then discharge mode.
Dynamite Ultra AC/DC Charger/Cycler www.DynamiteRC.com 9
A. D>C means that the charger will discharge first, then charge.
B. C>D means the charger will charge first, then discharge.
li-ion, li-Po and li-Fe
Charge Mode
warning:
C. D/1 flashing means the charger is in the discharge process and will charge when the discharge mode is complete.
D. C/1 flashing means the charger is in the charging process and will discharge when complete.
E. D/1 alternate flashing designates that the charger is in the cool down time period after discharging.
Li-Po batteries can cause serious injury and fire if charged inappropriately. Always confirm the battery voltage and series cell count is correct and never charge higher than a 1C rate. (1C
= charger current equals the battery capacity.
Example: A 1000mAh battery’s charge current limit is 1 amp. Example B 3300mAh battery’s charge current is 3.3A)
F. C/1 alternate flashing designates that the charger is in the cool down time period after charging.
Charge and discharge capacities in mAh will be displayed after the cycle is complete.
10 www.DynamiteRC.com
Li-Poly Charge
4.0A 14.8V(4S)
Message during li-ion/Poly Charging
Is 14.8V(4S) ?
No=Stop/Yes=Ente
Confirm if the number of selected battery cell is correct. To select the correct voltage, use the following formula to calculate the voltage of your pack: 3.7V/cell (e.g. 4S = 4*3.7=14.8V). Be careful to confirm the correct voltage and cell count. Failure to due so may result in damage or fire.
Dynamite Ultra AC/DC Charger/Cycler
Select Voltage
16.8V (4S)
1. Selected Charge Voltage
Input 13.01V
System Temp 36°C
2. Input Voltage/System Temperature
Safety Timer
ON 720min
3. Max Charge Time
Capacity Cut Off
ON 9900 mAh
4. Max Charge Capacity
4.12 4.13 4.11
4.12 0.00 0.00
5. Battery Voltage Per Cell
Dynamite Ultra AC/DC Charger/Cycler
High 4.131V (S2)
Low 4.119V (S3)
6. This screen shows which battery has the
High/Low Voltage
NOTE: The second battery has the maximum voltage.
The third battery has the minimum voltage.
Unbalanced Volt
12mV
7. Unbalanced Voltage
The voltage difference between the high voltage and low voltage cells in the battery pack.
Message after li-ion/Poly Charging
4.12 4.13 4.11
4.12 0.00 0.00
1. Battery Voltage Per Cell
High 4.131V (S2)
Low 4.119V (S3)
2. Which Battery has the High/Low Voltage
The second battery has the High voltage.
The third battery has the Low voltage.
Unbalanced Volt
12mV
3. Unbalanced Voltage
The voltage difference between the high voltage and low voltage cells in the pack.
www.DynamiteRC.com 11
li-ion/Poly Charge warning Message
li-ion/Poly Balance Charge Mode
ERR Batt
Over Voltage
Li-Poly Bal. Chg
4.0A 14.8V(4S)
1. Battery Over Voltage
WARN
Volt Select Err
Message during li-ion/Poly Balance
Charging
Li4S 0000:01 0001
Bal 0.10A 15.18V
2. Set Wrong Battery Voltage
ERR Batt
Low Voltage
3. Battery Low Voltage
See the status by turning switch to left/right
(same as Li-Ion/Poly Charge.)
Message after li-ion/Poly
Balance Charging
4.16 4.16 4.16
4.16 0.00 0.00
1. Battery Voltage Per Cell
High 4.165V (S2)
Low 4.162V (S3)
2. The above screen shows which battery has the High/Low voltage
NOTE: The second battery has the high voltage.
The third battery has the low voltage
Unbalanced Volt
3mV
3. Unbalance Voltage
The voltage difference between the high voltage and low voltage cells in the battery pack.
12 www.DynamiteRC.com
Dynamite Ultra AC/DC Charger/Cycler
li-ion/Poly Balance Charge warning Message
WARN
Volt Select Err
1. Set Wrong Battery Voltage
li-ion/Poly Discharge Mode
Li-Poly Dischg
1.0A 12.0V(4S)
Balancer
No Connect
2. Balance Leads not Connected
Message during li-ion/Poly Discharging
Li4S 0000:01 0001
DIS 1.00A 15.18V
See the status by turning the dial during discharge.
Unbalance Volt
Over 30mV
Select Voltage
12.0V (4S)
3. Shows that the unbalanced voltage is above the 10mV limit at 30mV. The charge will automatically switch to a 100mA charge rate until the battery cell voltages are balanced to less than 10mV. The charger will begin normal charging after the cells are balanced.
1. Selected Discharge Voltage Cutoff
Discharge voltage is pre-set to 3.00V/cell and the corresponding S count will be displayed along side the voltage cutoff being selected.
Selecting the correct S count will automatically set the appropriate voltage cutoff.
Cell Number 1
Volt Over 4.26V
Input 13.01V
System Temp 36°C
4. Battery voltage is over 4.26V per cell.
See previous step. The charger will drop to a low current rate until the cells are balanced within specifications.
2. DC Input Voltage/System Temperature
Dynamite Ultra AC/DC Charger/Cycler www.DynamiteRC.com 13
Pb Charge Mode
Pb Charge
4.0A 12.0V
Safety Timer
ON 720min
3. Max Charge Time
Suggested charge rate for PB charging is 0.3C
(i.e. .3 x 5Ah=1.5A).
Message during Pb Charging
Capacity Cut Off
ON 9900 mAh
Pb 000:01 0001
Chg 0.58A 14.21V
4. Max Charge Capacity
Pb Discharge Mode
See the status by turning dial during the charge process.
Pb Discharge
1.0A 10.8V
Select Voltage
14.7V
1. Selected Fast Charge Cutoff Voltage.
The cutoff value is predetermined when selecting the 2V, 6V, or 12V setting before charging and is not adjustable once charging has begun.
Corresponding discharge voltage for Pb battery packs:
1.8V (2V), 5.4V (6.0V), 10.8V (12V).
Message during Pb Discharging
Pb 000:01 0001
DIS 1.00A 11.96V
Input 13.01V
System Temp 36°C
See the status by turning the dial during the charging process.
2. Input Voltage/System Temperature
14 www.DynamiteRC.com
Dynamite Ultra AC/DC Charger/Cycler
Select Voltage
10.8V
1. Selected Discharge Voltage Cutoff
The discharge cutoff voltage value is predetermined when selecting 1.8V, 5.4V, or
10.8V setting for the corresponding 2V, 6V, or 12V battery being discharged and is not selectable during discharge.
Input 13.01V
System Temp 36°C
2. Input Voltage/System Temperature
warning information
1. If the battery connection is lost during operation, the OPEN/STOP error will flash.
Reconnect battery or replace.
2. Low Input Volt: Power input is below minimum requirements. Increase source power voltage.
3. Reverse Polarity: Battery polarity reversed
4. Waiting Overheating: Charger temperature overheated. Lower charge/discharge current rates and be sure the cooling fan is unobstructed.
5. After discharging, Ni-MH/END will flash alternately.
6. When the charge reaches the negative delta voltage, the Ni-MH/FULL is displayed.
7. When the charge reaches the Timed setting limit, the Ni-MH/TIME is displayed.
8. When the charge reaches the capacity setting limit, the Ni-MH/CAPA is displayed,
Ni-MH/CAPA will flash alternately.
9. When the charge reaches the Temperature setting limit, the Ni-MH/TEMP is displayed.
10. Li-Po/Li-Fe Battery Low Voltage, LOW/VOL will flash alternately.
11. Cooling fan is not working, FAN/STOP will flash alternately.
System Err
Return to Repair
12. Charger Breakdown
Current Err
Return to Repair
13. Charger Breakdown
Dynamite Ultra AC/DC Charger/Cycler www.DynamiteRC.com 15
safety Precautions warranty Period
1. Never leave the charger unattended during charging.
2. Do not allow children to charge battery packs unless supervised by a responsible adult.
3. Use only rechargeable batteries. This charger cannot charge batteries such as “heavy duty”,
“Alkaline battery”, or “Mercury battery.”
4. During use, please keep in a well ventilated area and never put beside inflammables.
5. This charger will be damaged if immersed in water or subjected to high level moisture. Do not use this charger in the rain or when your hand is wet to avoid electric shock or accident.
6. There is a fan inside this charger. To avoid accidents do not allow any foreign body to enter the fan.
7. The positive red lead (+) and negative black lead (-) terminals of the battery should be connected to the charger terminals correctly.
Do not reverse the positive and negative terminals. Wrong connection will damage the battery and may cause damage to the charger.
8. Before you start to charge, please ensure you selet correct charger settings. Double check if the battery count and type match your charger settings. Never set Li-Po and
Pb batteries at another mode, otherwise will cause the batteries to catch fire!
Exclusive Warranty- Horizon Hobby, Inc.,
(Horizon) warranties that the Products purchased (the “Product”) will be free from defects in materials and workmanship for a period of 5 years from the date of purchase by the Purchaser.
limited warranty
(a) This warranty is limited to the original Purchaser
(“Purchaser”) and is not transferable. REPAIR OR
REPLACEMENT AS PROVIDED UNDER THIS
WARRANTY IS THE EXCLUSIVE REMEDY OF
THE PURCHASER. This warranty covers only those Products purchased from an authorized
Horizon dealer. Third party transactions are not covered by this warranty. Proof of purchase is required for warranty claims. Further, Horizon reserves the right to change or modify this warranty without notice and disclaims all other warranties, express or implied.
(b) Limitations- HORIZON MAKES NO
WARRANTY OR REPRESENTATION, EXPRESS
OR IMPLIED, ABOUT NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE OF THE PRODUCT.
THE PURCHASER ACKNOWLEDGES THAT
THEY ALONE HAVE DETERMINED THAT
THE PRODUCT WILL SUITABLY MEET THE
REQUIREMENTS OF THE PURCHASER’S
INTENDED USE.
(c) Purchaser Remedy- Horizon’s sole obligation hereunder shall be that Horizon will, at its option,
(i) repair or (ii) replace, any Product determined by
Horizon to be defective. In the event of a defect, these are the Purchaser’s exclusive remedies.
Horizon reserves the right to inspect any and all equipment involved in a warranty claim. Repair or replacement decisions are at the sole discretion of
Horizon. This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or modification of or to any part of the Product. This warranty does not cover damage due to improper installation, operation, maintenance, or attempted repair by anyone other than Horizon. Return of any goods by Purchaser must be approved in writing by
Horizon before shipment.
16 www.DynamiteRC.com
Dynamite Ultra AC/DC Charger/Cycler
Damage limits Questions, assistance, and repairs
HORIZON SHALL NOT BE LIABLE FOR
SPECIAL, INDIRECT OR CONSEQUENTIAL
DAMAGES, LOSS OF PROFITS OR
PRODUCTION OR COMMERCIAL LOSS
IN ANY WAY CONNECTED WITH THE
PRODUCT, WHETHER SUCH CLAIM IS BASED
IN CONTRACT, WARRANTY, NEGLIGENCE,
OR STRICT LIABILITY. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted.
As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability.
If you as the Purchaser or user are not prepared to accept the liability associated with the use of this Product, you are advised to return this Product immediately in new and unused condition to the place of purchase.
Law: These Terms are governed by Illinois law
(without regard to conflict of law principals).
safety Precautions
This is a sophisticated hobby Product and not a toy. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this
Product in a safe and responsible manner could result in injury or damage to the
Product or other property. This Product is not intended for use by children without direct adult supervision. The Product manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or injury.
Your local hobby store and/or place of purchase cannot provide warranty support or repair. Once assembly, setup or use of the
Product has been started, you must contact
Horizon directly. This will enable Horizon to better answer your questions and service you in the event that you may need any assistance.
For questions or assistance, please direct your email to [email protected], or call 877.504.0233 toll free to speak to a service technician.
inspection or repairs
If this Product needs to be inspected or repaired, please call for a Return Merchandise
Authorization (RMA). Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. A Service Repair Request is available at www.horizonhobby.com on the “Support” tab. If you do not have internet access, please include a letter with your complete name, street address, email address and phone number where you can be reached during business days, your
RMA number, a list of the included items, method of payment for any non-warranty expenses and a brief summary of the problem. Your original sales receipt must also be included for warranty consideration. Be sure your name, address, and
RMA number are clearly written on the outside of the shipping carton.
warranty inspection and repairs
To receive warranty service, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your Product will be repaired or replaced free of charge. Repair or replacement decisions are at the sole discretion of Horizon Hobby.
Dynamite Ultra AC/DC Charger/Cycler www.DynamiteRC.com 17
non-warranty repairs
Should your repair not be covered by warranty the repair will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of the retail purchase cost. By submitting the item for repair you are agreeing to payment of the repair without notification. Repair estimates are available upon request. You must include this request with your repair. Non-warranty repair estimates will be billed a minimum of 1/2 hour of labor. In addition you will be billed for return freight. Please advise us of your preferred method of payment. Horizon accepts money orders and cashiers checks, as well as Visa,
MasterCard, American Express, and Discover cards. If you choose to pay by credit card, please include your credit card number and expiration date. Any repair left unpaid or unclaimed after
90 days will be considered abandoned and will be disposed of accordingly. Please note: nonwarranty repair is only available on electronics and model engines.
United states:
Electronics and engines requiring inspection or repair should be shipped to the following address:
Horizon Service Center
4105 Fieldstone Road
Champaign, Illinois 61822
USA
All other Products requiring warranty inspection or repair should be shipped to the following address:
Horizon Product Support
4105 Fieldstone Road
Champaign, Illinois 61822
USA
Please call 877-504-0233 or e-mail us at [email protected] with any questions or concerns regarding this product or warranty.
United Kingdom:
Electronics and engines requiring inspection or repair should be shipped to the following address:
Horizon Hobby UK
Units 1-4 Ployters Rd
Staple Tye
Harlow, Essex
CM18 7NS
United Kingdom
Please call +44 (0) 1279 641 097 or e-mail us at [email protected] with any questions or concerns regarding this product or warranty.
18 www.DynamiteRC.com
Dynamite Ultra AC/DC Charger/Cycler
germany:
Electronics and engines requiring inspection or repair should be shipped to the following address:
Declaration of Conformity
(in accordance with ISO/IEC 17050-1)
No. HH2009052101
Horizon Technischer Service
Hamburger Strasse 10
25335 Elmshorn
Germany
Product(s): DYN Passport Ultra AC/DC
Charger/Cycler
Item Number(s): DYN4064
Please call +49 4121 46199 66 or e-mail us at [email protected] with any questions or concerns regarding this product or warranty.
Equipment class: 1
Ce Compliance information for the european Union
The object of declaration described above is in conformity with the requirements of the specifications listed below, following the provisions of the European R&TTE directive
1999/5/EC: instructions for Disposal of weee by
Users in the european Union
This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or where you purchased the product.
EN55022
EN 61000-3-2
EN 61000-3-3
EN55024
EN 60950
Radio disturbance characteristics
Limits for harmonic current emissions
Conducted Emissions, Voltage
Flicker
Immunity characteristics
Safety
Signed for and on behalf of:
Horizon Hobby, Inc.
Champaign, IL USA
May 21, 2009
Steven A. Hall
Vice President
International Operations and Risk Management
Horizon Hobby, Inc.
Dynamite Ultra AC/DC Charger/Cycler www.DynamiteRC.com 19
Distributed exclusively by
Horizon Hobby, Inc.
4105 Fieldstone Road
Champaign, Illinois 61822
USA
(877) 504-0233 www.horizonhobby.com
©2009 Horizon Hobby, Inc.
15245
Printed 08/2009
advertisement
advertisement
Table of contents
- 2 Introduction
- 2 Specifications
- 3 Features
- 3 Available Charge Cords and Adapters
- 4 Available Balance Adapters
- 5 Input Power Connection
- 5 Charge Mode
- 5 Discharge Mode
- 5 Discharge/Charge Cycle Mode
- 5 Operating Instructions
- 6 User Setup Menu
- 7 Ni-MH and Ni-Cd Charge Mode
- 8 Ni-MH Discharge Mode
- 9 Ni-MH Discharge/Charge Cycle Mode
- 10 Li-Ion, Li-Po and Li-Fe Charge Mode
- 12 Li-Ion/Poly Balance Charge Mode
- 13 Li-Ion/Poly Discharge Mode
- 14 Pb Charge Mode
- 15 Warning Information
- 16 Safety Precautions
- 16 Warranty Period
- 16 Limited Warranty
- 17 Damage Limits
- 17 Safety Precautions
- 17 Questions, Assistance, and Repairs
- 17 Inspection or Repairs
- 17 Warranty Inspection and Repairs
- 18 Non-Warranty Repairs
- 19 for the European Union
- 19 Declaration of Conformity