Yard Machines 530 series Operator's Manual
Yard Machines 530 Series is a versatile tool designed to help you maintain your lawn and garden. With its powerful engine and durable construction, the 530 Series is perfect for edging along sidewalks, driveways, and flower beds. The adjustable cutting depth allows you to customize the depth of your edge, and the ergonomic handles provide a comfortable grip for extended use.
Tangazo
Tangazo
OPERATOR'S MANUAL
Model Series
530
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
Warning:
This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
covered, brush-covered or grass-covered land unless the enginefs exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark attester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 368022 Cleveland, Ohio 44136-9722.
MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722
PRINTED IN U.S.A. FORM NO. 770-10139A
(3/99)
SECTION 1: FINDING YOUR MODEL NUMBER
This Operator's Manual is an important part of your new edger.
It will help you assemble, prepare and maintain your edger. Please read and understand what it says.
Before you start to prepare your edger for its first use, please locate the model plate and copy the information from it in this Operator's Manual. The information on the model plate is very important if you need help from your dealer or the MTD customer support department.
See Figure 1.
• Every edger has a model plate. You can locate it by standing in the operating position behind the unit and looking down at the rear of the frame.
This is where your model number will be.
×XX-X-XXX-X-XXX XXXXXXXXXXX
This is where your serial number will be.
Copy the model number here:
..oooc.s
CLEVELAND, OHIO 44136
,.c
.,
Copy the serial number here:
Figure 1
SECTION 2: CALLING CUSTOMER SUPPORT
• LOCATE YOUR MODEL NUMBER AND SERIAL NUMBER -Record this information in the space
provided. To find your unit's specific model number and serial number, see SECTtON 1: FINDING
YOUR MODEL NUMBER.
• If you are having difficulty assembling this product or if you have any questions regarding the controls, operation or maintenance of this unit, please call the Customer Support Department.
• Customer Support can be reached by dialing: 1- (330) 220..4MTD
(4683) or
1- (800)-800-7310
• Please have your model number and serial number ready when you call.
• Although both numbers are important, you will be asked to enter only your serial number before your call can be processed.
2
SECTION 3: IMPORTANT SAFE OPERATION PRACTICES
WARNING:
THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF
NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF
YOURSELF AND OTHERS.
READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE YOUR EDGER.
FAILURE TO COMPLY WITH THESE
INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. WHEN YOU SEE THIS SYMBOL HEED
ITS WARNING.
WARNING:
The Engine Exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
DANGER:
Your edger was built to be operated according to the rules for safe operation in this
manual. As with any type of power equipment, carelessness or error on the part of the operator can
result in serious injury. If you violate any of these rules, you may cause serious injury to yourself or others.
1. TRAINING AND PREPARATION
• Read the operator's manual carefully.
Be thoroughly familiar with the controls and proper use of the equipment.
Know how to disengage the blade control and stop the unit quickly.
• Never allow children to operate equipment.
Never allow adults to operate equipment without proper instruction.
• Keep the area of operation clear (at least 50 feet) of all persons, especially small children and pets.
• Use the edger only as manufacture intended and as described in the operator's manual.
• Do not operate edger after it has been dropped or damaged.
• Return product to nearest authorized service facility for examination and repair. Do not operate product with damaged or excessively worn cutting blade.
• Dress properly-always wear safety glasses or goggles. Always wear safety footwear, and pants or slacks that cover your legs to reduce the risk of injury that may be caused by flying debris. Do not wear loose clothing or jewelry that can be caught in moving parts.
Use of gloves and substantial footwear is recommended when working outdoors.
Do not operate edger when barefoot or wearing sandals or open-toed shoes.
Wear boots, preferably with steel-toe caps.
• Objects struck by the blade can cause severe injuries to persons. The work area should always be carefully examined and cleared of all stones, sticks, wires, bones and other foreign objects, prior to edging.
• Never attempt to make any adjustments, other than depth of cut, while engine is running.
• The use of accessory attachments not recommended by the manufacturer may cause hazard and will void warranty.
• Never operate the edger without proper guards, plates or other safety protective devices in place.
• Turn engine off and disconnect spark plug wire:
• When not in use.
• Before servicing, cleaning and the like.
• Before changing accessories.
• Handle fuel with care; it is highly flammable
• Extinguish aU smoking materials and other possible sources of ignition.
• Use a fuel container acceptable for the purpose.
• Never add fuel to a running or hot engine.
• Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors.
• Replace gasoline cap securely.
• If fuel is spilled, move product and fuel container from area and do not create a source of ignition.
Wipe up spilled fuel.
2. OPERATION
• Make sure all nuts, bolts, and screws are kept tightly in place, especially the blade and all guards.
• Start the engine carefully. Make certain the blade is disengaged before attempting to start. Keep hands, feet, clothing, and the like well away from cutting blade and moving parts.
DANGER:
ROTATING CU'I-rING BLADE
• Keep both hands on handles when blade is rotating.
• Keep feet away from cutting area.
• Make sure engine is off and spark plug wire is disconnected when clearing jammed material from blade.
3
• Do not attempt to remove cut material nor hold material to be cut when engine is running or when cutting blade is moving.
CAUTION:
CUTTING BLADE COASTS AFTER
ENGINE IS TURNED OFF.
• Stay alert. Watch what you are doing. Use common sense.
• Do not operate edger when fatigued or under the influence of alcohol, drugs or heavy medication.
• Never operate the product without good visibility or light.
• Keep good looting and balance at all times. Do not overreach or stand on unstable support.
* Do not force or abuse product. It will do the job better and safer at the rate for which it was designed.
• Do not operate engine above speed necessary to do the job.
• Do not run the engine indoors; exhaust fumes are dangerous.
• Never direct discharge of material towards bystanders nor allow anyone near the area of operation.
Use care in directing discharge to avoid glass enclosures, automobiles, and the like.
• Stay alert for uneven sidewalks, holes in terrain or other similar conditions when using product.
Always push slowly over rough ground. Do not use the product on graveled surfaces.
• Do not operate edger in rain or wet locations.
• Always operate edger from behind the upper handle and position yourself where line of sight to cutting blade is blocked by guards.
• After striking a foreign object, shut off the engine, make absolutely sure the blade and all moving parts have completely stopped, disconnect the spark plug wire to prevent accidental starting, then thoroughly inspect the unit for any damage.
Such damage must be repaired before restarting and operating the edger. Remember, heavy vibration is generally a sign of trouble.
• Always stop engine when edging or trimming is delayed or when walking from one location to another.
• Stop the engine, wait for blade and all moving parts to stop before cleaning, adjusting, repairing or inspecting the product.
• Always disconnect spark plug wire to prevent accidental starting.
• Muffler and engine become hot during operation and can cause a burn. Allow to cool down before touching.
• Take all possible precautions when leaving the product unattended.
Disengage the blade, stop the engine and disconnect spark plug wire.
3, MAINTENANCE AND STORAGE
STORE PRODUCT INDOORS
• When not in use, store product indoors in a dry place, locked or otherwise inaccessible to children.
• Maintain product with care.
• Follow maintenance instructions given in this manual for your product.
• To reduce the risk of injury and engine failure, do not allow excessive grass, leaves or other debris to accumulate on or in the edger.
Wipe engine housing clean after each use.
• Keep air filter clean.
• Follow instructions for changing accessories.
• Replace any missing or damaged immediately.
labels
• Do not operate unit if blade is excessively worn or damaged.
• Replace with blade which meets original equipment specifications.
• Do not attempt to repair edger. Have mechanical repairs made by qualified dealer or repairman.
See that only identical replacement parts are used.
_,
read, understand and follow the warnings and instructions in this manual and on the machine.
WARNING - YOUR RESPONSIBILITY:
Restrict the use of this power machine to persons who
WARNING
CAUTION
Figure 2 Safety labels found on your unit
4
SECTION 4: SET-UP INSTRUCTIONS
IMPORTANT:
This unit is shipped WITHOUT
GASOLINE or OIL.
After setting up the unit, service engine with gasoline and oil as instructed in the separate engine manual packed with your unit,
NOTE: Reference to right or left hand side of the edger Lsobserved from the operating position.
HOW TO SET-UP YOUR EDGER:
1.
Disconnect the spark plug wire from the spark plug and ground it against the engine.
See
Figure 3.
Spark Plug
Wire Spark
Plug
V-Slot on Engine
3,
Tighten the wing knobs on the handle and pull the cable tie snugly to secure the cable to the lower handle. Carefully trim any excess portion of the cable tie after tightening.
See Figure 4.
Cable Tie
Lower Handle
J
Cable
,
Spark Plug
Wire
Spark
Plug
Figure 3
Raise the upper handle till it snaps into place. Be careful not to crimp or pinch the cables when lifting the handle.
Wing Knobs
Figure 4
ATTACHING THE STARTER ROPE
The rope guide is already attached to the right side of the upper handle of your edger.
See Figure 5.
1.
With the spark plug wire disconnected and grounded, stand behind the unit, hold the blade control handle against the upper handle and pull the starter rope out of the engine.
2.
Slip the rope through the rope guide, then tighten the wing nut to the upper handle.
NOTE: The starter rope will not pull out of the engine unless the blade control handle is squeezed against the upper handle.
Blade Depth
Control Lever
Rope
Guide
.,, .....
Blade Control
Handle
Upper
Handle
Spark
Plug
Blade
• .Guard
Belt Guard
Figure 5
5
CHECKING THE BLADE DEPTH
CONTROL
The blade depth control lever has been pre-adjusted at the factory, Before operating the edger, check the adjustment of the control cable as follows:
1.
Disconnect the spark plug wire and move it away from the spark plug.
2.
Move the blade depth lever to the lowest edging position then back to the start position on the handle.
See Figure 6.
3,
If the handle will not go to the start position, loosen the hex lock nut on the control cable and unthread the cable one turn. Again, move the handle to the start position. When this position is attained, hold the top of the cable with a pair of pliers and tighten the hex lock nut.
Blade Depth
Start
Position
Lowest
Edging
Position Hex Lock
Nut
Depth
Cable
Figure 6
SECTION 5: CONTROLS
The blade control handle is located on the upper handle of the unit. The blade control handle must be depressed in order to operate the unit. Release the blade control handle to stop the engine and the blade, See Figure 7.
Blade
Depth
Control
Lever
Recoil
Starter
Figure 7
THROTTLE CONTROL (If so equipped)
The throttle control lever may be located on the engine, if equipped.
It regulates the engine speed and stops the engine.
BLADE CONTROL HANDLE
WARNING:
This control mechanism is a
RECOIL STARTER
The recoil starter is attached to the handle. Stand behind the unit and pull the recoil starter to start the engine.
BLADE DEPTH CONTROL LEVER
WARNING:
The blade depth control lever is designed to minimize the risk of blade contact injury. Do not under any circumstances attempt to defeat the function of the blade depth control, or use the edger if the control is not adjusted properly.
The blade depth control lever does not engage the cutting blade.
Keep hands and feet away from edger blade whenever the engine is running.
The function of the blade depth control lever is to control the depth of the cut. To lower the blade to the cutting position, move the blade depth control lever to the left and move it forward to select the cutting depth.
The further forward the control lever is moved, the deeper or lower the cut.
PRIMER
The primer is used to pump gas into the carburetor.
Use it to start a cold engine, but do not use it to restart a warm engine after short shutdown. Refer to the separate engine manual packed with your edger.
BLADETI_ CONTROL
The cutting blade can be adjusted to five positions; from beveling to edging to trenching.
To adjust, make sure the engine is not running.
Release the blade adjustment lever on the pivot bracket and pivot the lever to the desired cutting position.
Place the blade adjustment lever in the notch desired.
See
Figure 8.
CURB WHEEL CONTROL (If so equipped)
On some models, the right rear wheel can be adjusted to edge along a curb.
The forward handle position is for normal edging operation.
Pull the control handle out and move handle towards the rear of the unit to compensate for the height of the curb.
See Figure 9.
\ Control
Handle
Blade Adjustment
Lever
Edging
Position
Normal
Operating
Position
Figure 9
NOTE: Become familiar with all the controls and adjustments before operating the edger so you can adjust it easily to a variety of edging conditions.
DO
NOT ATTEMPT TO MAKE ANY ADJUSTMENTS
while the engine is running.
Beveling
Position
Pivot
Bracket
Figure 8
Trenching
Position
SECTION 6: OPERATION
The operation of any edger can result in foreign objects being thrown into the eyes, which can result in severe eye damage.
Always wear safety glasses or eye shields.
We recommend wide vision safety mask for over spectacles or standard safety glasses
_hL WARNING:
Do not lower blade if the like.
The blade can strike the supporting surface, which could result in personal injury or property damage.
STARTING THE ENGINE
1.
Service the engine with gasoline and oil as instructed in the separate engine manual packed with your edger. Read instructions carefully.
,_
WARNING:
Never fill fuel tank indoors, been allowed to cool for at least two minutes after running.
2,
3,
Move the blade depth control lever back to the
START position (as far as it will go), and place it in the last notch. See Figure 6,
If equipped with throttle control lever on the engine, set the lever to the FAST (Rabbit) position.
NOTE:
Your engine may be a constant speed engine which is factory set at full throttle for best performance.
4.
Push the primer bulb in two or three times. Wait two to three seconds between each push. In cold weather (below 50°F, 19°C) push five (5) times.
NOTE: DO NOT USE PRIMER TO RESTART A
WARM ENGINE AFTER A SHORT SHUTDOWN.
5.
Standing behind the unit, depress the blade control handle and hold it against the upper handle.
See Figure 10.
6,
7,
Grasp starter handle and pull rope out slowly until engine reaches start of compression cycle
(rope will pull slightly harder at this point). Let the rope rewind slowly.
Pull rope with a rapid, continuous, full arm stroke.
Keep a firm grip on starter handle.
Return it slowly to the rope guide.
NOTE:
If the engine fails to start after three (3) pulls, push the primer two (2) times and pull starter rope again.
Edging Position
2,
Figure 11
Set the adjustment lever (refer to Figure 8) in the first or second notch at the top for beveling. See
Figure 12.
Figure 10
STOPPING THE ENGINE
To stopthe engine:
1.
Release the blade control handle to stop the engine.
2.
If equipped with a throttle control lever on the engine, set the lever to the SLOW (turtle) position.
3.
Disconnect spark plug wire and ground to prevent accidental starting while equipment is unattended.
OPERATING THE EDGER
3.
Beveling Position
Figure 12
Set the adjustment lever (refer to Figure 8) in the fourth or fifth notch at the bottom for trenching.
See Figure 13.
7
_lb WARNING:
Rotating cutting blade may
Keep area clear of bystanders and do not operate without guards in place.
1.
Set the adjustment lever (refer to Figure 8) in the middle notch of the blade tilt control to edge vertically.
See Figure 11.
Trenching Position
Figure 13
Right Rear
Wheel
\
EDGING ALONG CURB (If so equipped)
To edge along a curb on units equipped to do so, lower the right rear wheel by moving the curb wheel control lever toward the rear of the unit, pivoting the wheel to the desired depth and releasing the lever.
Refer to Figure 9.
When edging the grass along a curb, the unit will ride on the two rear wheels and the support roller behind the blade.
See Figure 14. The wheel at the front of the unit is not used.
/
Support
Roller
Figure 14
SECTION 7: ADJUSTMENTS
WARNING: Do not at any time make any adjustment to edger without first stopping the engine and disconnecting spark plug wire.
BLADE DEPTH CONTROL ADJUSTMENT
Refer to Checking the Blade Depth Control in the
Set-Up Instructions section for any adjustments.
CARBURETOR ADJUSTMENTS
Minor carburetor adjustments may be required to compensate for differences in fuel, temperature, altitude and load. To adjust carburetor, refer to the separate engine manual packed with your mower.
NOTE: A dirty air cleaner will cause an engine to run rough.
Be certain air cleaner is clean and attached carburetor.
to the carburetor before adjusting
_
WARNING:
If any adjustments are
running (e.g. carburetor), keep clear of all moving parts.
Be careful of heated surfaces and muffler.
SECTION 8: LUBRICATION
WARNING: Always stop engine and disconnect spark plug wire before cleaning, lubricating or doing any kind of work on edger.
ENGINE
Refer to the engine manual for lubrication instructions.
WHEELS
Lubricate the wheels and bearings at least once a season with light oil or engine oil. Also if the wheels are removed for any reason, lubricate the surface of the axle bolt and the inner surface of the wheel with light oil.
PIVOT POINTS
Lubricate the pivot points on the blade control handle, blade depth control lever and the blade adjustment lever with _ight oil at least once a season.
CUTTING HEAD BEARINGS
The two ball bearings in the blade spindle housing are lubricated and sealed at the factory and require no lubrication.
Lubricate all other moving parts with engine oil.
SHAFT
Lubricate the two bearings and under the compression spring on the shaft with light oil frequently during the season.
See Figure 15.
9
Belt Guard
/
Nut
Hex Lock
Lube_
3,
Figure 16
Install one bell washer (cupped side toward blade), the blade, and the other bell washer.
See Figure 17.
Lube
Figure 15
SECTION 9: MAINTENANCE
WARNING:
Disconnect the spark plug wire and ground against the engine before performing any adjustment, repairs or maintenance,
ENGINE
Refer to engine manual for complete instructions for care and maintenance of engine.
BLADE REMOVAL and INSTALLATION
Removal
1.
Use a wrench on the bolt head on the side of the belt guard and a wrench to remove the hex lock nut holding the blade, See Figure 16,
2.
Remove the blade and two belt washers.
Nut
_-Blade
Blade
3ulde
4.
Figure 17
Secure with the previously removed lock nut.
Tighten the Iocknut to between 450 in. Ibs to 600 in. Ibs.
BELT REMOVAL
Pay particular attention to how belt is alined on the blade spindle pulley to assist in reassembly.
1.
Drain the gas and oil,
2.
Place the blade adjustment lever in the bevel position.
Refer to Figure 8.
10
Belt Guard
Figure 18
3.
Remove the belt guard.
The blade can be removed for convenience.
See Figure 18,
SECTION 10: OFF-SEASON
STORAGE
The following steps should be taken to prepare unit for storage.
1.
Clean and lubricate unit thoroughly according to the lubrication section.
2.
Refer to engine manual for correct engine storage instructions.
3.
Coat edging blade with chassis grease to prevent rusting.
4.
Store unit in a dry, clean area. Do not store next
to corrosive materials, such as fertilizer.
NOTE: When storing any type of power equipment
in an poorly ventilated or metal storage shed, care should be taken to rustproof the equipment. Using a
light oil or silicone, coat the equipment, especially springs and bearings.
Engine _"_"
I
Pulley'_o
Belt
Wood
Block pindle Housing
Figure 19
NOTE: Do not tip the unit forward unless gas and oil have been drained.
4.
Place a block of wood on the floor and tip the unit forward resting the blade spindle housing on the block of wood.
Apply force down to compress the spring on the blade shaft. Remove the belt from the engine pulley, then lift belt off blade pulley.
See Figure 19.
5.
Reinstall the replacement belt and hardware in the reverse order of disassembly.
Refer to
Figure 17.
6.
Replace oil and gasoline specifications in the engine manual.
according to
11
SECTION 11: TROUBLE SHOOTING GUIDE
Trouble
Engine tails to start
Engine runs erratic
Possible Cause(s)
Dirty air cleaner.
Choke not in ON position.
Fuel tank empty, or stale fuel.
Throttle control lever not in starting position.
Spark plug wire disconnected.
Faulty spark plug.
Engine flooded.
Spark plug wire loose.
Stale fuel.
Engine overheats
Vent in gas cap plugged.
Water or dirt in fuel system.
Dirty air cleaner.
Carburetor out of adjustment.
Engine oil level low.
Air flow restricted.
Excessive vibration at blade
Belt slips
Dirty air cleaner.
Carburetor not adjusted properly.
Spindle bent.
Ball bearings worn out.
Belt worn or stretched
Corrective Action
Reter to the engine manual packed with your unit.
Move switch to ON position.
Fill tank with clean, fresh gasoline. Fuel will not last over
thirty days unless a fuel stabilizer is used.
Move throttle lever to FAST position.
Connect wire to spark plug.
Clean, adjust gap or replace.
Refer to the engine manual packed with your unit.
Connect and tighten spark plug w=re.
Fill tank with clean, fresh gasoline. Fuel will not last over thirty days unless a fuel stabilizer is used.
Clear vent.
Drain fuel tank. Refill with fresh fuel.
Refer to the engine manual packed with your unit.
Refer to the engine manual packed with your unit.
Fill crankcase with proper oil.
Stop engine and disconnect spark plug wire. Refer to the engine manual packed with your unit.
Refer to the engine manual packed with your unit.
Refer to the engine manual packed with your unit.
Replace spindle.
Replace ball bearings.
Adjust clutch rod or replace belt.
Note: For repairs beyond the minor adjustments above, contact your local authorized service dealer.
12
Notes
13
Model Series 530
79
\
90
45
71
9O
91 92
2O
83
4
16
2
3
75
72
94 66
44
\
37
34
34
I
I
I I 52
I
14
Model Series 530
37
38
4g
41
42
43
44
45
46
47
48
4g
5[
NO.
1
2
3
4
10
1
23
24
25
26
9
20
21
22
4
5
2
3
6
7
8
27
28
29
30
31
32
33
5_
54
PART NO.
720-0297
747-0976
746-1098
712-0324
720-0142
781-0742
710-0116
710-0578
746-1094
781-0741
710-1205
732-0369
712-0429
726-0299
736-0451
749-1225
710-1174
631-0079
710-0502A
710-3013
1731-1935
781-0746
1756-1150
712-0413
736-0317
781-0080
712-0318
750-1163
710-0642
781-0740
731-1942
741-0155
750-1158
731-1939
719-0387
732-0862
736-0342
736-0116
710-1241
731-1929
756-0449
681-0140
731-1932
726-0100
747-0991
714-0104
711-1171
731-1931
734-1840
DESCRIPTION
Foam Grip "i---
Blade Control Handle iControl Cable 31.75
Hex Lock Nut 1/4-20 iDepth Lever Grip t
Depth Lever
Hex Screw 5/16-18 x 2.0 Lg.
Thrust Screw 1/4-20 x 1.5
Depth Cable. 44.5
Depth Bracket
Eye Bolt 1/4-20
Compression Spring .550 O.D. x 1.3
Hex Lock Nut 5/16-18
Push Cap
Washer .320 ID x .93 O.D.
Upper Handle
Carriage Bolt 5/16-18 x 2.0 Lg.
Edger Base Ass y
Tapp Screw w/Hex Lock Wash 3/8-16
Hex Screw 1/4-20 x.50 Lg.
Discharge Shield Deflector
Deflector Keeper
Engine Pulley
Hex Jam Nut 5/8-18
Bell Washer .63 I.D. x 1.25 O.D. x .18
Blade
HexJamNut5/8-t8
Spacer .628 x .875 x .545 Lg.
HxScr.
w/Wash.:TT:1/4-20x.750Lg.
Blade Guide
Blade Guard
Ball Bearing .62 I.D. x 1.38 O.D. x .4
Spacer .628 x .875 x 1.818 Lg.
Belt Guard
Spindle w/Insert
Compression Spring: Arbor
Flat Washer .283 I.D x .75 O.D. x .030
|
Fiat Washer .635 I.D, x .93 O.D. x .06 |
|
|
]
Hex Screw w/W/ash 1/4
Front Rod Handler |
|
Pulley .
Curb Whl Bracket Ass y t
Curb Roller t
Push Cap t
Rod 5/16-24 1-
Cotter Pin .072 x 1.12 t
Ferrule 5/16-24 x .312 t
Black Bushing .515 Dia x .62 t
_Wheel 7 x 1.7 Aero Gray
|
|
|
|
|
|
|
|
|
_
|
]
|
REF.I
J NO.
I PART NO.
1 56
88
89
90
90
91
92
94
95
96
97
98
99
100
101
102
--
83
84
85
86
87
1710-1627
|
|
J
|
|
|
|
|
|
]
|
|
57
58
59
|
|
J 60
61
62
63
64
65
66
67
68
69
70
71
|
|
|
|
|
|
|
|
|
|
|
J
72
73
74
75
76
77
L738-0507B
1736-0105
1734-1841
/736-05o4
/738-0102
/731-0981A
78
79
/781-0749
/681-0139
80 |715-0121
81 }720-0230
82 /711-1269
/ 711-1278
754-0343
/710-0191 i738-0481
/736-0320
1681-0141
1731-1930
/731-1887
1712-3020
J732-0667
781-0747
/747-0993
1756-0625
1781-0745
]781-0744
1732-0866
1736-3068
749-1078
710-0134
_781-0781
736-3040
712-3020
710-3180
732-0188A
720-0241
710-1237
751B213146
710-1017
720-0279
781-0758A
736-0258
715-0143
736-0452
750-1179
736-0329
712-0287
726-0240 t DESCRIPTION
Hex Bolt 5/8-_
V-Belt
Hex Screw: 3/8-24 x 1.50 Lg.
Shoulder Screw .500 x 2.62:3/8-16
Flat Washer .38 OD x 1.38 OD
Front Wheel Brkt Ass'y.
Rear Rod Handler
Hubcap: Spoke w/Hole Gray "i-
Jam Lock Nut 3/8-16
Torsion Spring
Cable Keeper
Idler Rod
CabLe Roller Pulley
Index Plate t
Pivot Arm t
Spring Lever t
Shoulder Bolt .500 x .434 Lg. !-
Bell Wash..401
ID.x .870 OD. x ,063 t
Wheel: 8 x 1.7 Aero Gray
Wave Washer .510 I.D. x ,750 O.D. t
Shoulder Bolt .498 x 1.445: 3/8-16 1
Hubcap: Radia Spoke Gray t
Tilt Bracket
[Adj. Lever Ass'y
Pin 1/4 x 2.0" Lg.
Foam Grip t
Axle
Curb Axle T
Flat Wash..531
I.D. x .875 O.D. x .06
Lower Handle
Carriage Screw 1/4-20 x .62
Index Plato Back Plate
Fiat Wash..406
ID x 1.92 OD x .06 t
Hex Lock Nut 3/8_16 t
Hex Screw 5/16-18 x 1.75 Lg.
Torsion Spring t
Wing Knob Nut 5/16-18
Hex Scr. w/V/ash, :T: #10-32 x .625 Lg,
Throttle Clamp
Screw. 1/4-14 x .625 Lg.
Handle Knob
Base Support
Flat Washer
Roll Pin
Bell Washer .396 ID x 1.14 OD
Spacer .520 ID x .860 Lg.
Lock Washer 1/4
Hex Nut 1/4-20
Cable Tie (Not Shown) t If Equipped
15
MANUFACTURER'S LIMITED WARRANTY FOR:
The limited warranty set forth below is given by MTD
PRODUCTS INC ("MTD") with respect to new merchandise purchased and used in the United States, its possessions and territories.
MTD warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in material or workmanship.
This limited warranty shall only apply if this product has been operated and maintained in accordance with the Operator's Manual furnished with the product, and has not been subject to misuse, abuse, commercial use, neglect, accident, improper maintenance, alteration, vandalism, theft, fire, water or damage because of other peril or natural disaster. Damage resulting from the installation or use of any accessory or attachment not approved by MTD Products Inc. for use with the product(s) covered by this manual will void your warranty as to any resulting damages.
Normal wear parts or components thereof are subject to separate terms as follows: All normal wear part or component failures will be covered on the product for a period of
90 days regardless of cause. After 90 days, but within the two year period, normal wear part failures will be covered
ONLY IF caused by defects in material or workmanship of
OTHER component parts. Normal wear parts and components include, but are not limited to, belts, blades, blade adapters, grass bags, rider deck wheels, seats, snow thrower skid shoes, shave plates and tires. Batteries are covered by a 90-day limited replacement warranty.
HOW TO OBTAIN SERVICE: Warranty service is available,
WITH PROOF OF PURCHASE THROUGH YOUR LOCAL
AUTHORIZED SERVICE DEALER. To locate the dealer in your area, please check for a listing in the Yellow Pages or contact the Customer Service Department of MTD PROD-
UCTS INC by calling 1-800-800-7310 or writing to P.O. Box
368022, Cleveland, Ohio 44136-9722.
No product returned directly to the factory will be accepted unless prior written permission has been extended by the Customer Service
Department of MTD PRODUCTS INC.
This limited warranty does not provide coverage in the following cases: a. The engine or component parts thereof. These items carry a separate manufacturer's warranty. Please refer to the applicable manufacturer's warranty on these items.
b. Routine maintenance items such as lubricants, filters, blade sharpening and tune-ups, or adjustments such as brake adjustments, clutch adjustments or deck adjustments; and normal deterioration of the exterior finish due to use or exposure.
c. Log splitter pumps, valves and cylinders have a separate one year warranty.
d. MTD does not extend any warranty for products sold or exported outside of the United States of America, its possessions and territories, except those sold through MTD's authorized channels of export distribution.
No Implied warranty, Including any implied warranty of merchantability or fitness for a particular purpose, applies after the applicable period of express written warranty above as to the parts as identified. No other express warranty or guaranty, whether written or oral, except as mentioned above, given by any person or
entity, including a dealer or retailer, with respect to any product shall bind MTD. During the period of the Warranty, the exclusive remedy is repair or replacement of the product as set forth above.
(Some states do not
allow limitations on how long an implied warranty lasts, so
the above limitation may not apply to you.)
The provisions as set forth in this Warranty provide the sole and exclusive remedy arising from the sales. MTD shall not be liable for incidental or consequential loss or damages including, without limitation, expenses incurred for substitute or replacement lawn care ser-
vices, for transportation or for related expenses, or for rental expenses to temporarily replace a warranted
product. (Some states do not allow the exclusion or limita-
tion of incidental or consequential damages, so the above
exclusion or limitation may not apply to you.)
In no event shall recovery of any kind be greater than the amount of the purchase price of the product sold. Alteration of the safety features of the product shall void this Warranty. You assume the risk and liability for loss, damage, or injury to you and your property and/or to others and their property arising out of the use or misuse or inability to use the product.
This limited warranty shall not extend to anyone other than the original purchaser, original lessee or the person for whom it was purchased as a gift.
How State Law Relates to this Warranty: This limited
warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
Pakua
Kiungo cha umma kime sasishwa
Kiungo cha umma kwa mazungumzo yako kimesasishwa. You may view and manage your chat links after registration here.
Kiungo cha umma cha hati
Tangazo