- Home
- Domestic appliances
- Small kitchen appliances
- Barbecues & grills
- Cuisinart
- G53509
- Owner's manual
advertisement
ASSEMBLY
MANUAL
Cuisinart
®
Gourmet 750
85-3122-0 (G53509) Propane
85-3123-8 (G53510) Natural Gas
READ AND SAVE MANUAL FOR FUTURE REFERENCE.
Assemble your grill immediately.
Missing or damaged parts should be claimed within 30 days of purchase.
For product inquiries, parts, warranty and troubleshooting support, please call 1-800-309-3452.
www.cuisinartbbqs.com
LIMITED 5-YEAR WARRANTY
Manual Revision #: 10112018 JC
2
H E A V Y A R T I C L E N E E D S 2 T O L I F T
THIS MANUAL MUST REMAIN WITH THE PRODUCT AT ALL TIMES
To ORDER non-warranty replacement parts or accessories, or to register your warranty, please visit us on the web at
www.cuisinartbbqs.com
CAUTION
Sharp edges. Wear gloves when assembling your grill.
CAUTION
Read and follow all safety statements, assembly instructions, use and care directions before attempting to assemble and cook.
DANGER
1. If you smell Gas: a. Shut off gas to the appliance b. Extinguish any open flame c. Open lid d. If odor continues, keep away from the appliance and immediately call your gas supplier or your fire department
2. Do not store or use gasoline or other flammable liquids or vapours in the vicinity of this or any other appliance.
3. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
INSTALLER OR
ASSEMBLER/CONSUMER
This manual should be kept with the BBQ at all times.
WARNING
Failure to follow all of the Manufacturer’s instructions could result in hazardous fires, explosions, property damage, or serious personal injury or even death.
Follow all leak check procedures carefully prior to operation of barbecue, even if grill was dealer assembled. Do not try lighting this BBQ without reading the Lighting Instructions section of the
Safety and Care Manual that accompanies this grill.
DANGER
1. Do not store or use gasoline or other flammable liquids or vapours in the vicinity of this or any other appliance.
2. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
CAUTION
Avoid burns. The stainless steel and steel surfaces of this barbecue can become extremely hot, in direct sun and while the barbecue is in operation.
T H I S B A R B E C U E I S F O R O U T D O O R U S E O N LY
CUISINART ® CUSTOMER CARE HOTLINE
1-800-309-3452
HARDWARE PACK
Tools Needed for Assembly
• #2 Phillips screwdriver (long and short)
• ¼ ” Slotted screwdriver (long and short)
• Adjustable wrench
• Pliers
• Rubber Mallot
For correct hardware assembly, always position the lock washer between the screw and the flat washer.
Screw
Lock Washer
Flat Washer
No. Description
1 1/4-20UNCx38 Screw
8
9
6
7
10
11
12
4
5
2
3
1/4-20UNCx16 Screw
NO. 10-24UNCx13 Screw
ST4.2x10 Tapping Screw
ST4.2x20 Tapping Screw
φ7 Lock Washer
φ7 Washer
Rubberized Washer
φ5 Lock Washer
φ5 Washer
Control Knob
U Pin
Part Number
20120-13038-250
20120-13016-250
20124-10013-250
22500-42010-137
22500-42020-137
41400-07000-250
40300-07000-250
G501-0054-9100
41400-05000-250
40300-05000-250
G618-0014-9000
G350-0026-9000
Qty.
8
26
22
4
12
12
1
1
18
12
6
1
Note: Do not fully tighten all the nuts during this initial stage
Caution:
Sheet metal can cause injury. Wear gloves when installing this grill.
1
4
1/4-20UNCx38 Screw
X 8
ST4.2x10 Tapping Screw
X 6
2
1/4-20UNCx16 Screw
X 18
5
ST4.2x20 Tapping Screw
X 1
3
6
NO.10-24UNCx13 Screw
X 12
φ7 Lock Washer
X 26
7 8 9
φ7 Washer
X 22
Rubberized Washer
X 4
φ5 Lock Washer
X 12
10 11 12
φ5 Washer
X 12
Control Knob
X 1
U Pin
X 1
BEFORE ASSEMBLING THE BARBECUE, READ THESE INSTRUCTIONS CAREFULLY.
Assemble the barbecue on a flat, clean surface. Grill is heavy. Two people are recommended to complete assembly.
1
2
CL
CM
CN
CO
CP
CH
CI
CJ
CK
CE1
CE2
CF
CG
CA
CB
CC
CD
PARTS LIST (PROPANE) FOR 85-3122-0 (G53509)
BD
BE
BF
BG
BH
BA1
BA2
BB
BC
Item No.
Qty. Description
AA
AB
AC
AD
AE
AF
1
1
1 Thermometer
1
2
2
Top lid
Lid Handle
Thermometer Bezel
Screw for Top Lid
Lid Bumper
1 Burner Box Assembly
1 Burner Box Surround
3 Main Burner
1 Carryover Assembly
3 Flame Tamer
3 Cooking Grate
1 Warming Rack
1 Match Holder
2 Lid Support Pin
Part No.
G535-5400-01
G525-0033-01
G512-0085-01
G535-0052-01
G359-0030-01
G527-0002-01
G535-3600-01
G535-3100-01
G525-3800-02
G535-0033-01
G525-0015-01
G525-0016-01
G525-0017-01
G501-0068-01
G525-0014-02
EE
EF
EG
EH
EI
EA
EB
EC
ED
Item No.
Qty. Description
DF
DG
DH
DI
DB
DC
DD
DE
DJ
DK
1
1
1
1
Side Shelf Fascia, Right
Infrared Support Frame
Infrared Zone Side Burner
Electrode Set, Infrared Zone
Part No.
G535-4100-01
G535-3500-01
G535-8600-01
G614-0092-01
1 Lid, Infrared Zone G501-0070-02
1 Cooking Grate, Infrared Zone G525-0055-01
1 Infrared Grease Tray
1 Infrared Side Burner Wind
Shield
G614-0075-01
G614-0073-01
1 Side Shelf Table, Left
1 Side Shelf Fascia, Left
G535-0600-01
G535-0700-01
1 Left Cart Side Panel
1 Right Cart Side Panel
1 Bottom Shelf, LP
2 Wheel with Lock
2 Wheel
1 Left Door Assembly
1 Right Door Assembly
2 Door Handle
4 Door Magnet Assembly
G535-0009-0 1A
G535-0010-0 1A
G535-0900-01
G350-0023-01
G350-0024-01
G535-5800-01
G535-5900-01
G517-0011-01
G501-00F2-03
1 Manifold Assembly, LP
1 Regulator
G535-6300-01
G510-0006-01
1 Infrared Side Burner Valve, LP G535-0023-01
1 Metal Hose G508-0024-01
1 Electronic Ignition Assembly G535-0031-01
1 Electronic Ignition Battery Cap G535-0031-02
3 Electrode Set, Main Burner
4 Control Knob
G525-0030-01
G618-0014-01
4 Bezel, Control Knob
1 Control Panel
1 Front Brace
1 Grease Tray
1 Upper Back Panel
1 Heat Shield
1 Left Track
1 Right Track
1 Lower Back Panel
G418-0038-01
G535-0008-01
G535-5000-01
G350-4400-01
G535-0054-01
G525-0022-01
G515-0024-01
G515-0025-01
G535-0053-01
F1
F2
F3
F4
1 Hardware pack
1 Assembly Manual
1 Safe Use and Care Manual
1 Tank Screw
G535-B005-01
G535-M009-01
G535-M009-02
G505-0047-01
DA 1 Side Shelf Table, Right G535-0400-01
EXPLODED DIAGRAM (PROPANE)
FOR 85-3122-0 (G53509)
BF
BE
AE
AF
AA
AC
AD
AB
BC
BB
BD
CA
CP
DK
CF
CD
CC
BH
CB
DJ
CE2
CE1
CJ
CL
CN
CK
EH
EA
EF
CO
BA2
BH
BA1
CI
DC
EC
BG
EH
CH
DF
CG
DE
EB
ED
CM
DA
DB
DI
DH
EG
DD
DG
EI
EI
EE
Hardware
Pack
F1
EXTRAS
Assembly
Manual
F2
Safe Use
& Care
Manual
F3
Tank
Screw
F4
3
4
CL
CM
CN
CO
CP
CH
CI
CJ
CK
CE1
CE2
CF
CG
CA
CB
CC
CD
PARTS LIST (NATURAL GAS) FOR 85-3123-8 (G53510)
BD
BE
BF
BG
BH
BA1
BA2
BB
BC
Item No.
Qty. Description
AA
AB
AC
AD
AE
AF
1
1
1 Thermometer
1
2
2
Top lid
Lid Handle
Thermometer Bezel
Screw for Top Lid
Lid bumper
1 Burner Box Assembly
1 Burner Box Surround
3 Main Burner
1 Carryover Assembly
3 Flame Tamer
3 Cooking Grate
1 Warming Rack
1 Match holder
2 Lid Support Pin
Part No.
G535-5400-01
G535-0033-01
G512-0085-01
G535-0052-01
G359-0030-01
G527-0002-01
G535-3600-01
G535-3100-01
G525-3800-02
G535-0033-01
G525-0015-01
G525-0016-01
G525-0017-01
G501-0068-01
G525-0014-02
EE
EF
EG
EH
EI
EA
EB
EC
ED
Item No.
Qty. Description
DF
DG
DH
DI
DB
DC
DD
DE
DJ
DK
1
1
1
1
Side Shelf Fascia, Right
Infrared Support Frame
Infrared Zone Side Burner
Electrode Set, Infrared Zone
Part No.
G535-4100-01
G535-3500-01
G535-8600-01
G614-0092-01
1 Lid, Infrared Zone G501-0070-02
1 Cooking Grate, Infrared Zone G525-0055-01
1 Infrared Grease Tray
1 Infrared Side Burner Wind
Shield
G614-0075-01
G614-0073-01
1 Side Shelf Table, Left
1 Side Shelf Fascia, Left
G535-0600-01
G535-0700-01
1 Left Cart Side Panel
1 Right Cart Side Panel
1 Bottom Shelf, NG
2 Locking Wheel
2 Wheel
1 Left Door Assembly
1 Right Door Assembly
2 Door Handle
4 Door Magnet Assembly
G535-0009-0 1A
G535-0010-0 1A
G535-3400-01
G350-0023-01
G350-0024-01
G535-5800-01
G535-5900-01
G517-0011-01
G501-00F2-03
1 Manifold Assembly, NG
1 Natural Gas Hose
G535-6600-01
G501-0099-01
1 Infrared Side Burner Valve, NG G535-0027-01
1 Metal Hose G508-0024-01
1 Electronic Ignition Assembly G535-0031-01
1 Electronic Ignition Battery Cap G535-0031-02
3 Electrode Set, Main Burner
4 Control Knob
G525-0030-01
G618-0014-01
4 Bezel, Control Knob
1 Control Panel
1 Front Brace
1 Grease Tray
1 Upper Back Panel
1 Heat Shield
1 Left Track
1 Right Track
1 Lower Back Panel
G418-0038-01
G535-0008-01
G535-5000-01
G350-4400-01
G535-0054-01
G525-0022-01
G515-0024-01
G515-0025-01
G535-0053-01
F1
F2
F3
1 Hardware Pack
1 Assembly Manuals
1 Safe Use and Care Manual
G535-B005-01
G535-M009-01
G535-M009-02
DA 1 Side Shelf Table, Right G535-0400-01
EXPLODED DIAGRAM (NATURAL GAS)
FOR 85-3123-8 (G53510)
BF
BE
AE
AF
AA
AC
AD
AB
BC
BB
BD
CB
CA
CF
CD
CC
BH
DJ
CP
DK
CE2
CE1
CJ
CL
CN
CK
EH
EA
EF
CO
BA2
BH
BA1
CI
DC
EC
BG
EH
CH
DF
CG
DE
EB
ED
CM
DA
DB
DI
DH
EG
DD
DG
EI
EI
EE
Hardware
Pack
F1
EXTRAS
Assembly
Manual
F2
Safe Use
& Care
Manual
F3
5
6
ASSEMBLY INSTRUCTIONS
1.
EE
ED
A
Back view
EC
EE
Separate the 2 different types of wheels:
2 Locking Wheels (ED) and 2 Regular Wheels
(EE).
Insert the U Pin (#12) into one of the regular
Wheels (EE), as shown in image B. Attach the
Regular Wheel (EE) to the front of the Bottom
Shelf (EC), and use the U Pin (#12) to secure and tighten.
Repeat for remaining 3 Wheels (EE & ED).
NOTE: Regular Wheels (EE) need to be assembled to the front of the Bottom
Shelf (EC), and Wheels with Lock (ED) need to be assembled to the back of the Bottom Shelf (EC), as shown in image A.
YOU WILL NEED:
12
B
Close up X 1
2.
EB a. Ensure that the wheels are firmly locked in
the “ON” position before continuing. b. Assemble the Left Cart Side Panel (EA) and
the Right Cart Side Panel (EB) to the Bottom
Shelf (EC).
EA
EC
YOU WILL NEED:
6 7
A
Front view
X 6 X 6 X 6
EB
EC
B
Close up
ASSEMBLY INSTRUCTIONS
2.
EB
CP
EA
EC
C c. Assemble the Lower Back Panel (CP)
to the Left Cart Side Panel (EA) and Right
Cart Side Panel (EB).
YOU WILL NEED:
6 7
X 4 X 4 X 4
3.
EB
A
Back view
TIP: The top of the lower back panel (CP) can be identified by the four recesses located on the top of this part.
CP
D
Close up
EB
CJ
CJ
CP
EA
Attach the Front Brace (CJ) to the Left and
Right Cart Side Panels (EA and EB).
TIP: One person should align the left side, while the second person assembles the right side.
YOU WILL NEED:
6 7
EA
X 2 X 2 X 2
TIP: The bottom of the front brace (CJ) can be identified by the four recesses located on the bottom of this part.
B
Close up
7
ASSEMBLY INSTRUCTIONS
4.
A+B
THIS STEP REQUIRES 3 PEOPLE.
DO NOT ATTEMPT ALONE. EXTREMELY
HEAVY.
a. Position the Top Lid and Burner Box
Assembly (A and B) onto Cart Assembly (C), as shown.
A
Front view
C
Close up - left outside view
A+B
EB
B
Back view
8
C
Front view
EA
CJ EB
EA b. Assemble Burner Box Assembly (A and B) to the Left and Right Cart Side Panels (EA and
EB), as shown.
YOU WILL NEED:
6 7
X 4 X 4 X 4 c. Assemble the front of the Burner Box
Assembly (A and B) to the Front Brace (CJ), as shown.
YOU WILL NEED:
6 7
X 2 X 2 X 2
ASSEMBLY INSTRUCTIONS
5.
CL
EB
A
Back view
EA
Attach the Upper Back Panel (CL) to both the
Left and Right Cart Side Panels (EA and EB).
Only install hardware in the bottom portion of the Upper Back Panel (CL), as shown in figure
B.
DO NOT TIGHTEN SCREWS UNTIL SIDE
SHELF HAS BEEN INSTALLED.
YOU WILL NEED:
6 7
X 2 X 2 X 2
CL
B
Close up
EA
9
10
ASSEMBLY INSTRUCTIONS
6.
DJ
BA
A
DK
Front, left side view
B2
DJ
B
DK
View inside burner box a. Open the Lid. Assemble the Left Side Shelf
Assembly (DJ and DK) to the Cart Assembly by inserting the Side Shelf tabs into holes on the Cart Assembly (figure A).
BA b. Secure using hardware, as shown in figure
B, C and D.
YOU WILL NEED:
6 8
X 2 X 2 X 2
TIP: Ensure that the rubber side of the rubberized washer makes contact with the burner box.
DJ
C
View under left side shelf (back)
DJ
BA
DK
YOU WILL NEED:
6
X 1 X 1
7
X 1
BA
D
View under left side shelf (front)
DK
YOU WILL NEED:
9 10
X 3 X 3 X 3
NOTE: Beware of sharp edges.
ASSEMBLY INSTRUCTIONS
7.
CE1
Plastic Nut
CE2
A a. Remove the Electronic Ignition Battery Cap
(CE2) and the plastic nut from the Electronic
Ignition Assembly (CE1).
DJ
B
Left side view
CE1
CE2
DK
Plastic Nut b. Feed the Electronic Ignition Assembly (CE1) through the opening in the Left Side Shelf
Fascia (DK) and secure using the nut.
DJ c. Insert one “AA” battery into the battery compartment with the positive end facing outward, as shown. Secure using the
Electronic Ignition Battery Cap (CE2).
-
+
CE2
DK
C
Front, left side view
11
12
ASSEMBLY INSTRUCTIONS
7.
DJ
CE1
DK
D
BA
View under left side shelf
CF
DE
CE1
E
TIP: The Electrode set for Main Burner (CF), the
Electrode wire for Infrared Zone (DE) can be found fastened together hanging from the left side of the Control Panel on the outside of the burner box (BA) as shown.
d. Insert all Electrode wires (CF, DE) into the
Electronic Ignition Assembly (CE1), as shown in figure E.
NOTE: All main burner and side burner electrode wire connection points are the same size.
ASSEMBLY INSTRUCTIONS
8.
BA
DA a. Open the lid. Assemble the Right Side Shelf
Assembly (DA and DB) to the Cart Assembly by inserting the Side Shelf tabs into the holes on the Cart Assembly (figure A).
A
Front, right side view
DB
Close up
DA
BA
B
View inside burner box
DA
DC
C BA
View under right side shelf (back) b. Secure using hardware, as shown in figure B,
C and D.
YOU WILL NEED:
6 8
DB
X 2 X 2 X 2
TIP: Ensure that the rubber side of the rubberized washer makes contact with the burner box.
YOU WILL NEED:
6 7
X 1 X 1 X 1
13
14
8.
9 .
DB
DC
YOU WILL NEED:
9 10
X 3 X 3 X 3
NOTE: Beware of sharp edges.
D
View under right side shelf (front)
BA
DA
CC
DB a. Remove the hardware that is pre-assembled to the Infrared Side Burner Valve (CC), as shown in figure A. b. Insert the Infrared Side Burner Valve stem
(CC) through the rear of the Right Side Shelf
Fascia (DB). Assemble the Side Burner Valve
(CC) to the Side Shelf Fascia (DB), using the hardware removed (figure A).
A
Front, right side view
DB
DA
CC
11 c. Assemble the Side Burner Control Knob
(#11) to the Infrared Side Burner Valve (CC)
(figure B).
YOU WILL NEED:
X 1
B
Front, right side view
ASSEMBLY INSTRUCTIONS
9 .
DI
DC
C
Front, right side view
DI d. Assemble the Infrared Side Burner Wind
Shield (DI) to the Infrared Support Frame
(DC), as shown in figure C and D.
YOU WILL NEED:
DC
X 2
NOTE: Two people recommended.
D
View from above right side shelf
DD e. Position the Infrared Zone Side Burner (DD) through the opening in the Infrared Support
Frame (DC).
DC
E
Front, right side view f. Make sure that the Infrared Zone Side Burner
(DD) engages the Side Burner Valve (CC) gas jet, as shown in figure F.
CC
DD
F
View from underneath right side shelf
15
ASSEMBLY INSTRUCTIONS
9 .
DC
DD
G
View from above right side shelf
DD
DE
H
View from above right side shelf
DC g. Assemble the Infrared Zone Side Burner (DD) to the Infrared Zone Support Frame (DC), at the 2 points indicated in figure G.
YOU WILL NEED:
9 10
X 2 X 2 X 2 h. Feed the Infrared Zone Electrode set (DE) from underneath the Infrared Zone Side
Burner (DD), through the small opening on the left side of the Infrared Zone Support
Frame (DC). Align and assemble the electrode using the self tapping screw provided, as shown in figure H.
YOU WILL NEED:
5
X 1 i. Position the Infrared Zone Cooking Grate
(DG) on the Infrared Zone Support Frame
(DC).
DG
DC
I
Front, right side view j. Insert the Infrared Grease Tray (DH) into the back of the Infrared Zone Support Frame
(DC), as shown.
16
J
DC
Back, right side view
DH
ASSEMBLY INSTRUCTIONS
10.
A
Back view
CM
CM
CL
CM
Close up, back
CL a. Position the Heat Shield (CM) into the two hooks located on the bottom of the Upper
Back Panel (CL), as shown in figure A.
B
Front view
CJ
CM
CJ b. Assemble the Heat Shield (CM) to the bottom of the Front Brace (CJ), as shown in figure B.
YOU WILL NEED:
X 2
CM
Close up, front
17
18
ASSEMBLY INSTRUCTIONS
11.
CJ
A
Front view
CN
CO a. Assemble the Left and Right Tracks (CN and
CO) for the Grease Tray (CK), as shown in figure A-C.
b. Both the Left and Right Tracks (CN and CO) should be inserted into the two clips located on the Upper Back Panel (CL), as shown in figure B.
CN CL
CO
B
Close up, back
CJ
CN
C
Close up, front
CO c. Assemble the front of the Left and Right
Tracks (CN and CO) to the Front Brace (CJ), as shown in figure C.
YOU WILL NEED:
X 2 d. Insert the Grease Tray (CK) into the opening of the Upper Back Panel (CL).
CK
D
Back view
CL
ASSEMBLY INSTRUCTIONS
12.
EH
EG
A
13.
Assemble the Door Handle (EH) to the Left and
Right Door Assembly (EF and EG) as shown in figure A.
YOU WILL NEED:
9 10
X 4 X 4 X 4 a. Assemble the Right Door Assembly (EG), to the Bottom Shelf (EC) by inserting the fixed pin (bottom of door) into the hole provided
(figure B).
EG
A
EC
C
Top of door
CJ
B
Bottom of door
EC
EG
EG b. Assemble the top of the Door Assembly (EG) to the Front Brace (CJ), by pressing in the door support pin and aligning with the hole located on the top right corner of the door.
TIP: Use a paint scraper to press-in the support pin, while the second person aligns the door. The support pin will lock into position when the door is assembled correctly. c. Repeat steps a and b for the Left Door
Assembly (EF).
19
ASSEMBLY INSTRUCTIONS
14.
BD
Place the Flame Tamers (BD) into the Burner
Box (BA).
15.
BE a. Place the Cooking Grates (BE) into the
Burner Box (BA), as shown.
20
16.
A
BF
BA b. Assemble the Warming Rack (BF) by inserting the fixed pins into the warming rack support bars located on the Burner Box (BA), as shown in figure A and B.
B
Close up
ASSEMBLY INSTRUCTIONS
17.
CB
EB
A
B
CB
FOR PROPANE MODELS ONLY.
For natural gas model, follow step 18.
a. Position the Regulator Hose (CB) through the hole in the Right Side Panel (EB).
b. Position the 20 lb propane tank onto the
Bottom Shelf (EC), and secure using the
Bolt (F4) (already attached) located on the underside of the Bottom Shelf, as shown in figure C.
c. Attach the regulator coupling nut to the LP cylinder valve. Be careful not to cross thread.
Hand tighten only.
d. Perform Leak Test. See page 5 of the
Cuisinart ® Safety and Care Manual.
ATTENTION: For your families safety, do not attempt to light this BBQ until you have reviewed pages 4-7 of the
Cuisinart ® Safety & Care Manual.
All Safety and Leak Test MUST BE
PERFORMED BY THE END USER, prior to lighting this BBQ.
WARNING Do not store extra propane tanks within BBQ cart.
EC
F4
C
21
22
ASSEMBLY INSTRUCTIONS
18.
A
CB
B
CC
CB
Natural Gas
Home Supply
Quick Connector
FOR NATURAL GAS MODEL ONLY. a. Attach the Natural Gas Hose (CB) to the Side
Burner Valve (CC) as shown, and wrench tighten. b. Perform Leak Test. See page 6 of the
Cuisinart ® Safety and Care Manual.
ATTENTION: In order to complete installation of your Natural Gas BBQ a 1/2” or 3/8” adapter may be required to connect your BBQ’s Natural Gas hose to your home gas supply.
Contact your Natural Gas supplier to purchase the necessary part.
ATTENTION: For your families safety, do not attempt to light this BBQ until you have reviewed pages 4-7 of the
Cuisinart ® Safety & Care Manual.
All Safety and Leak Test MUST BE
PERFORMED BY THE END USER, prior to lighting this BBQ.
WARNING: For all new, at home, natural gas connections please contact a certified gas technician to install your natural gas barbecue.
WARNING HOT SURFACES
!
!
!
• CAUTION!
• AVOID BURNS!
• DO NOT TOUCH WHEN BBQ IS IN USE!
• EXTREMELY HOT SURFACE!
* SHADED AREAS BECOME EXTREMELY HOT WHEN IN USE.
Visit www.cuisinartbbqs.com to complete product registration.
Cuisinart
®
Gourmet Barbecues Customer Service:
1-800-309-3452
Join the conversation facebook.com/cuisinartbbqs twitter.com/cuisinartbbqs
Cuisinart ® is a registered trademark used under license
© 2019 Trileaf Distributions Trifeuil
advertisement
Related manuals
advertisement