advertisement
GRAND Golden Line G480 UM14800
Rigid Inflatable Boat
Golden LINE
Models:
G480LF, G480GLF
G480EF, G480GEF
User’s Manual
GRAND Golden Line G480 UM14800
INTRODUCTION.
"GRAND" inflatable motor boat of the "GOLDEN LINE" series: G480LF, G480EF has been designed under requirements of ISO 6185 "Plastomer and Elastomer Inflatable Boats" and DIN 7870 "Inflatable Boats with Reinforced
Shells".
PURPOSE.
The rigid inflatable motor boat of the "GOLDEN LINE" series relates to the category of pleasure boats and is intended for water sports, tourism, the use as a floating means on board of launches, yachts and other vessels.
-2-
GRAND Golden Line G480
TECNICAL DATA SPECIFICATION
Model
Length overall
Length inside
Width overall
Width inside
Tube diameter max
Number of chambers
Passenger capacity
Load capacity
Boat weight
Engine power recommended
Engine power max
Engine weight max
Engine shaft length
Boat design Category(Dir.94/25/EC)
-3pers.
kg lbs kg lbs
HP kW
HP kW kg lbs
Unit m ft-inches m ft-inches m ft-inches m ft-inches m ft-inches
G480LF/G480GLF/G480EF/G480GEF
4,55
14'11"
3.4
11'2"
2,10
6'11"
1,05
3'5"
0,51
20"
5
6
900
1980
265
583
50
36,8
75
55,2
175
385
20"(long)
C
UM14800
GRAND Golden Line G480 UM14800
COMPLETE SET
Model G480LF/G480GLF G480EF/G480GEF
Description unit q-ty availability availability
1. Standart feature
1.1 Deep “V” hand-laid fiberglass hull with antiskid surfase
1.2
Towing bow eye
1.3
1 front and 2 rear lifting eyes
1.4
Cocpit drain system
1.5
Fiberglass step ends of inflatable tube
1.6
Soft curvdmulti-chamber buoyancy tube
1.7
Doubled tough raised rubbing strake
1.8
Molded-in bow and rear stowages with cushions
1.9
Steering console CL-03
1.10 Steering console CL-08
1.11
Steering csustem with cable and steering wheel
1.12
2 stainless steel side railings for rear seat
1.13 Wide bow step plate with pull-ap cleat and navigation light
1.14 Footpump, 2 paddles
1.15 Maintetenance kit, User”s manual pcs.
pcs.
set.
set..
pcs.
pcs.
pcs pcs.
set..
pcs pcs pcs set..
1
1
1
1
2
1
1
1
1
2
1
1
1
-4-
GRAND Golden Line G480
COMPLETE SET
Model
Description
2. GRAND LUXE feature
2.1
Battery container
2.2
Disconnector and battery wire
2.3
Marine boat cable
2.4
Marine switches
2.5
Fuses
2.6
Bilge pump
2.7
Electric accessory socket
2.8
Fuel tank 55l
2.9
Fuel send
2.10 Filler
2.11 Vent
3. Optional equipment
3.1
Speedometr
3.2
Tachometer
3.3
Fuel meter
3.4
Marine compass
3.5
St.steel waterski mast
3.6
Keel a protectors
-5-
UM14800
G480LF/G480GLF G480EF/G480GEF
unit q-ty availability availability pcs.
pcs.
pcs.
pcs.
pcs..
pcs.
pcs.
pcs.
pcs.
pcs.
pcs.
3
1
1
1
1
1
3
1
1
1
1 pcs.
pcs.
pcs.
pcs.
pcs.
1
1
1
1
1
GRAND Golden Line G480
COMPLETE SET
Model
Description
3.7
Tube protectors
3.8
Stainles steelnavigation arch
3.9
Overal cover
3.10 Sttering consolte cover
3.11
Removable sundeck with cushion
3.12 Bimini top
3.13 Removable bow table
UM14800 unit
G480LF/G480GLF G480EF/G480GEF Í q-ty availability availability pcs.
pcs.
pcs.
pcs.
pcs.
pcs.
1
1
1
1
1
1
√√√√√
—
Your "GRAND" boat "GOLDEN LINE" complete set included this items.
Note: Perfection of the design and improvment of quality of our products is the fundamental production policy of our company. Therefore, alternations may be made to the complete set (and as the components parts become available).
-6-
GRAND Golden Line G480
3
12
9
14
5
1
7
10
G480LF
-7-
17
19
15
11
2
8
13
20
6
18
UM14800
4
GRAND Golden Line G480
5
1
11
3
12
19
9
7
10
14
G480EF
-8-
17
19
6
18
21
2
8
13
UM14800
GRAND Golden Line G480
16
21
15
UM14800
Pos.
Item
7
8
9
10
11
12
3
4
5
6
1
2
Fiberglass hull
Buoyancy tube nflation / deflation valve
St. steel arc
Towing bow eye
Stern lifting eyes
Bow step plate with rope cleat
Fuel filler
Antiskid deck surface
Doublead raised rubbing strake
Safety grab handles
Molded-in bow stowage with cushion
13
14
15
16
17
18
Molded-in stern stowage with seat cushion
Molded-in console CL-08 with front stowage, cushion
Rear seat back with cushion
Hull drain plug
Steering wheel
Pull-up cleat (stern)
19 Navigation lights
20 Electric horn
21 Fiberglass step ends of inflatable tube
22 Stainless steel side railings for rear seat
-9-
GRAND Golden Line G480
PREPARATION FOR EXPLOITATION
In order to set the boat in the operation condition perform as follows:
unfold the inflatable tube;
mount the outboard engine on the transom in accodance with it`s own installation instruction.
extend the engine remote control cables and steering cable from engine mounting place to steering console mounting place through the holes on the deck and helm stowage.
STEERING CONSOLE INSTALLATION
-fix overhead part of the steering console to lower part by means of head screws M4X16, washers and arrester nuts
M4 from complete set (see Fig.1);
ïðèñîåäèíèòü òðîñ óïðàâëåíèÿ ê ðóëåâîìó
attach steering system cable in accodance with its own installation (manual);
connect electric cable to the steering console (see wiring diagram);
close and fix overhead part of steering console by means of washers and nuts M8 from complete set n order to install the windscreen onto the console perform the next operations ( Fig. 1A ):
align the holes in the windscreen with the holes in console overhead part;
fix windscreen by means of the shaped screws M6x25,
bushs, washers and nuts M6 from the complete set;
ATTENTION ! To avoid the water penetration into the console inner layers, please, tight all the hole free space with any water resistant filler.
-10-
Fig. 1
Fig. 1A
UM14800
Pos Item
1 Screw
2 Bush #1
3 Bush #2
4 Windscreen
5 Steering console
6 Cup
7 Serrated lock washer
8 Washer
9 Nut
6 2 4 3 5 7 1
GRAND Golden Line G480
SOFT BACK OF STERN LOCKER SEATING MOUNTING
In order to install the stern locker seat-back, perform the next:
- hinge out the seat of stern locker;
- insert back support into the holes of stern surface;
- fix seat-back by means of the bolts M6x50, shaped washers, washers and arrester nuts M6 from the complete set;
- tighten all the bolts;
- replace the locker seat.
Fig. 2
UM14800
ARC MOUNTING
In order to install the arc, perform the next:
hinge out the seat of stern locker;
insert the arc stud in the stern surface holes ;
fix arc by means of the bolts M12X40 , nuts M12 and washers from the complete set (see Fig. 3);
connect electric cable of arc with main electric cable (see wiring diagram);
tighten all the bolts and nuts;
replace the locker seat.
Fig. 3
-11-
GRAND Golden Line G480
SUNDECK MOUNTING
In order to install the sundeck, perform the next operations:
- open the bow locker and console front seating:
- insert the sundeck floor board into the specified recesses in the bow and console lockers;
- close the bow locker and console front seating:
- hinge out and fix the support of the sundeck by means of the
ring-bolt from the complete set;
- set the sundeck cushions on the press-buttons (see Fig. 4)
Fig. 4
CONSOLE EQUIPMENT
Console equipment included:
- steering system;
- steering cable;
- steering wheel;
- tachometer (1) (optional equipment);
- speedometer (2) (optional equipment);
- electric accessory socket (3) ;
- handle (7):
switches and fuses
navigation lights and meter lamp switch (6);
hull drain pump switch (7);
horn switch (8).
UM14800
Fig.5
7
2
4
3
1 6 5
-12-
GRAND Golden Line G480
INFLATION / DEFLATION VALVES OPERATION
The inflation/deflation valve is intended for:
—filling the compartment with air from a standart pump or filling system and maintaining pressure in the tube for prolonged time,
—adjustable drop of pressure in compartment.
The air fill valve is designed as a tab-type non-return valve.
Every inflation / deflation valve includes the following parts : valve body 1, valve nut 5, valve cap 2 with strap 3, washerwith gasket 4, spindel 6 with spring 7, cup diaphragm 8 ( Fig.6).
INFLATION MODE : valve is closed with gasket 4 tight . To move the valve to deflation mode : push the button 6 and turn it clockwise to fix it in lower position
DEFLATION MODE : button is fixed in lower position. To move the valve to inflation mode : push the button 6 and turn it counter clockwise. The button goes to upper position.
ATTENTION !
1. Overinflating of your boat, when the air pressure is
more than nominal, sufficiently decreases the boat
life time.
2. The valves are airtight just in case they are closed with
the caps tight.
3. The tube is airtight in case it keeps its form for 8
hours at least.
13
4 1 2 3
UM14800
Fig.6
5 6 8 7
GRAND Golden Line G480
CONSOLE
Fuel meter
S
+12v panel light
3A
I
+12v on ignition switch
4A
B
GRN
B
Wiring diagram
Speedometer
GRN
Signal
Tachometer
XS
B
3A
+12v on ignition switch
3 2A 4
3
2
SA3
FU3
1 3
2
SA2
FU2
1
3
2
SA1
FU1
X1- Connector block
1
3A
3
4
2A
A
B
1
4
5
2
3
6
7
8
9
10
Wire legend
Navigation light
Panel light
Horn
Bilge pump
Bilge pump (auto)
+12v disconnector
-12v battery
A
4A B
Fuel send
Ground
Fuel tank
Disconnector
B
Outboard motor
-12v
Ground
- 12v +
Battery
+12v
7
8
9
10
5
6
1
2
3
4
1
3
4
2A
A
B
QS
A
NAVIGATION ARCH
UM14800
1 B 3 B
HL3
B
1
Masthead light (white) HA Horn
B
HL1 Port light (red)
Starboard light (green)
1
HL2
1 3 B
1 3 B
4
2A
B
Brown/white
Brown
Black
Bilge pump
14
GRAND Golden Line G480
MAINTENANCE
Main conditions of long service life is right and careful service.
Avoid excessive increasing of pressure in the board, especially from heating by the sun rays.
After exploitation take off sand and dirt from boat surface, and carefully dry it.
Avoid the water getting into the chambers. If a fuel or an oil / gas gets to the boat surface it is necessary to wash the soiling place by soap water as soon as possible and dry.
Pay attention to the condition of bottom and seat surfaces. If the coating is destroyed it is necessary to dry this element and restore the defend ply.
After the season prepare the boat to winter keeping.
Clean boat surface from sand and dirt and make the necessary repairs, if damages take place. If it is possible, keep the boat in the open and slightly pumped state in air temperature 0-
25°C. The boat must be protected from the sun rays.
Insignificant boat repairing (eliminating the board punctures or cuts) you may carry out by yourself. In this case use the coated fabric patches from the complete set. Ask your dealer for the correct type of glue you may use for the repair.
In case if sufficient damagesof hull, tube body, partitions or seams it is recommended to apply for professional repair in authorised service station.
OPERATING REGULATIONS
UM14800
OPERATING REGULATIONS
Dear user,
We thank your for your purchase and do hope that you will have a great fun of it. However, to make your joy and pleasure complete, we would request you to read carefully and observe the directions and recommendations specified b e l o w .
IT IS STRICTLY FORBIDDEN : to handle the boat in the state of intoxication and without individual rescue means being used (life-saving belts, jackets, etc.)
IT IS FORBIDDEN :
- to overload the boat above the design weight-carrying capacity;
- to use an outboard engine of power exceeding the maximum
allowable value;
- to bring the tube pressure up to the value exceeding the rated
one ( 0.15 bar );
- to drag the boat across a rough surface.
Danger of usage of engine having insufficient or e x c e s s i v e p o w e r
According to the safety regulations, each inflatable boat should be furnished with an outboard engine having the maximum allowable power. You will find the data on the maximum allowable power of the engine on the manufacturer's plate with the designation of the model type inscribed thereon.
The plate is fixed in the afterbody of the boat. However, your should choose the engine power within the allowable range so as to ensure that you may safely reach the shore when heading into the wind or into the current.
-15-
GRAND Golden Line G480
Observation of local shipping regulations
For each particular water area the local shipping regulations are in force. You may apply for information to the appropriate water transport and shipping directorate, as well as to the water police.
Proper usage of boat equipment and accessories
Use the boat equipment and accessories only on their direct purpose to ensure reliable service.
Availability of Oars
Even when sailing with an outboard engine you should always have the oars available with you so that you were able to reach the shore without outside assistance in case of any damage to the boat.
Usage of emergency stop switch
On your request any outboard engine seller may provide your engine with the emergency stop switch. During navigation the switch should be connected to the wrist of your hand by means of a cord. In case you fall overboard, even if being a steersman, the switch will cut out the engine and the propeller.
This arrangement will enable you to avoid any traumas and to reach the boat.
Prevention of damages caused by electrolyte or fuel leakages
Take all possible precautions against penetration of fuel or electrolyte from the storage battery into the inflatable boat. If it does happen wash thoroughly the fouled spots with water.
Cargo arrangement and stowing, attachment of items and prevention of falling overboard
You should be always sure that the number of people on board never exceeds that specified in the user's manual or on the manufacturer's plate provided on the transom. The boat will retain an adequate floatability and will not keel over only provided that the load is arranged reasonably. Therefore,do
-16-
UM14800 not accommodate all passengers on the same side of the boat.
Arrange the cargo to be carried uniformly inside the boat, all items being reliable secured on the bottom of the boat. All passengers should be accommodated inside the boat. The occupied seats should not be left throughout the entire sail ing time. When sailing with an outboard engine the steersman should shift his body forward in the course of acceleration to prevent the boat forebody from raising under the force of upthrust waves.
Presence of sharp and pricking objects on board
Despite the strong shell of the boat we are recommended to handle sharp and pricking objects being on board with care.
For example, it concerns a knife blade, fish-hook point, etc.
Rocky shore, mole, shoals (for example, sand banks, coral reefs, rocks)
Approach rocky shores, shoals, moles, etc. carefully to avoid damages to the boat. It is strictly prohibited to drag the boat across rough surfaces (shingle, rocks, concrete, etc.).
Check at navigation
In case of prolonged navigation with the use of an outboard engine, regularly check to ensure that the engine is reliably attached to the boat. If the engine was attached carelessly the attachment may work loose under the action of vibration.
Besides, check air chambers pressure at regular intervals, since the pressure may vary under the effects of outside air temperature and atmospheric pressure variations.
Never forget to monitor regularly the quantity of fuel in the fuel tank. Keep always in mind that the quantity of fuel should be sufficient for you to sail to your final destination.
Availability of rescue means (life-saving jackets, distress signals, spare parts)
If you are planning to go beyond the protected water areas you should provide all passengers on board with life-saving
GRAND Golden Line G480 jackets. All passengers should put on life-saving jackets under strong wind and heavy seaways conditions. Those passengers who cannot swim should always carry the lifesaving jackets while on board! It is also recommended to keep constantly distress signal means on board.
Towing
At towing the towing rope length should not be at least 3 lengths of the boat, the rope being secured to both boats in a manner ensuring its immediately, single-motion release. The steersman of the towed boat should be assisted by another crew member to monitor the process of towing. In this case, certain communication gestures should be agreed upon beforehand.
Damage to one of air chambers
The inflatable boat is designed to provide an adequate stability in case of the complete damage to one the air chambers
(balloon compartments) at the expense of the remaining air chambers and the hull. Thanks to it, you will be able to reach safely the nearest shore. Reduce the speed and shift your body to the undamaged part of the boat. Watch changes in stability. After this immediately head for the nearest shore. To prevent penetration of water into the boat, pull the shell of the damaged air chambers upwards.
Anchor and mooring fast fastening
Fix the anchor and towing ropes in the forebody of the boat to the front towing ring. Fix the back spring on the transom via special holes.
Danger of currents and wind
Before navigation of the boat in unfamiliar waters make detail inquiries about local conditions and regulations! Currents, wind, shoals, rising and falling tides, as well as weather variations may imply serious danger!
UM14800
In emergency stay in boat
In any unexpected situation (engine failure, boat damage, etc.) do not ever leave the boat provided it is still afloat. Even if you believe that the shore is just nearby stay in the boat, since you will be looked for in this particular place and, most probably, will be found. Should the boat become partially flooded throw heavy objects (batteries, fuel tank, engine) overboard to ensure additional floatability.
The "GRAND" Company employees would like to wish you a pleasant and safe leisure time!
-17-
advertisement
Related manuals
advertisement