Wzzard™ Mesh Gen2 Starter Bundles

Refrigeration Monitoring Kit

Model BB-WSK-REF-2

SETUP MANUAL

REFRIGERATION MONITORING KIT

Advantech - Americas

707 Dayton Road

Ottawa, IL 61350 USA

Phone:

1 (815) 433-5100

Fax:

1 (815) 433-5105

Advantech - European Headquarters

Westlink Commercial Park

Oranmore, Co. Galway, Ireland

Phone:

+353 91-792444

Fax:

+353 91-792445

www.advantech.com [email protected]

Documentation Number: pn2003BREF00_r1_BB-WSK-REF-2_1319m

2

REFRIGERATION MONITORING KIT

CONTENTS

REFRIGERATION MONITORING STARTER KIT ................................................................................................. 4

WZZARD MESH NETWORK SETUP ...................................................................................................................... 4

DOWNLOADING REFRIGERATION MONITOR Node-RED™ FLOW TO THE GATEWAY .......................... 5

POINT THE MQTT DATA TO THE INTERNAL MQTT BROKER ..................................................................... 12

WAKE UP WZZARD™ MESH EDGE NODE ....................................................................................................... 14

ACCESS Node-RED™ UI IN THE GATEWAY .................................................................................................... 15

NETWORK HEALTH PAGE .................................................................................................................................... 16

ATTACHING THE SENSORS ON THE INTELLIGENT EDGE NODES .......................................................... 17

MOUNTING YOUR SENSORS .............................................................................................................................. 18

ACCESSING THE DASHBOARD .......................................................................................................................... 19

SETTING UP AN E-MAIL ACCOUNT ................................................................................................................... 20

SETTING UP YOUR DROPBOX FOR LOGGING ............................................................................................... 22

APPENDIX A. CARRIER TEXT MESSAGING URL ADDRESSES .................................................................. 25

Node-RED™ SOFTWARE LICENSE .................................................................................................................... 27

ADVANTECH TECHNICAL SUPPORT ................................................................................................................. 28

3

REFRIGERATION MONITORING KIT

REFRIGERATION MONITORING STARTER KIT

Kit Model BB-WSK-REF-2

The Wzzard™ Mesh Refrigeration Monitoring Application Kit provides a non-intrusive, easily installed solution for monitoring internal and external temperature, door open/closed and current draw on refrigeration equipment without disrupting your existing facility operations. Email or text message alerts can be sent when user-configured high or low limits are exceeded in critical applications.

Installation costs are kept low using the Wzzard Mesh Wireless Sensing platform. The platform creates a self-forming, self-healing wireless mesh network that eliminates the need for wires and requires no special skills to install. Each Wzzard sensor node is powered by long life batteries.

Using Node-RED™, a simple, browser based application pre-installed on the gateway, you can monitor your cooler or freezer performance from any web browser on your network.

The contents of the kit include:

Qty 1 BB-WCD1H2102H Commercial Temperature/Humidity Wzzard Mesh Node

Qty 2 BB-JC10F50-V

Qty 1 BB-WCHCBL

50A Clamp-on Current Sensor

Thermistor/Breakout Cable

Qty 1 BB-WCHMS Door Sensor Cable

Qty 1 SmartSwarm 342™ Ethernet Wzzard Mesh Gateway

WZZARD MESH NETWORK SETUP

The Wzzard Mesh Node and Gateway in this kit are preconfigured. If this is the only Wzzard

Mesh device in your vicinity, it will need no further configuration. If other Wzzard Mesh gateways or nodes are nearby and unclaimed, you will need to claim the gateway and the node. See respective node and gateway manuals for instructions.

4

REFRIGERATION MONITORING KIT

DOWNLOADING REFRIGERATION MONITOR NODE-RED™ FLOW TO THE

GATEWAY

NOTE: The gateway must be in operational and online state in order to add the HVAC application (ie Eth1 must be plugged in).

1. Follow the instructions in the Gateway’s Quick Start Guide to claim your gateway.

2. Select View Devices from the dropdown menu on the SmartWorx™ Hub home screen:

3. Select your device from the list of available devices:

5

4. Select Add/Upgrade Apps tab.

REFRIGERATION MONITORING KIT

6

REFRIGERATION MONITORING KIT

5. Check the box next to REF . A list of components to be updated will appear.

7

6. Click OK to accept the download.

REFRIGERATION MONITORING KIT

8

REFRIGERATION MONITORING KIT

7. Click Add/Upgrade Selected to start the download.

9

REFRIGERATION MONITORING KIT

8. The download could take several minutes. To monitor the progress, select History from the

Manage Device screen.

10

REFRIGERATION MONITORING KIT

9. As each component is updated, it will be indicated with a



check mark:

NOTE : “AddNode” commands will show an X if they have already been installed.

Note : If, for some reason all or a portion of the installation fails, repeat the procedure to install the rest of the package.

11

REFRIGERATION MONITORING KIT

POINT THE MQTT DATA TO THE INTERNAL MQTT BROKER

1. From the Manage Device screen, click the Wzzard™ Mesh application.

12

REFRIGERATION MONITORING KIT

2. Fill in the Application Settings screen as shown and click the Apply Changes button:

13

REFRIGERATION MONITORING KIT

WAKE UP WZZARD™ MESH EDGE NODE

1. Press and hold the Config/Status button for 5 seconds until the Status LED starts blinking.

2. Check LED.

3. After you have awakened the node, the LED will begin to blink. This indicates that the node is attempting to establish a network connection. The LED will cease blinking when a connection is made or after 10 seconds. Press the Config/Status LED for approximately 1 second to view the LED status.

LED Indicator

OFF

(after button press)

Slow Blink

(1 per second)

Solid ON

Fast Blink

(10 per second)

Status

Node is asleep or dead battery.

Attempting to establish connection with Wzzard mesh network.

Node is connected to a gateway.

Firmware update in progress.

14

REFRIGERATION MONITORING KIT

ACCESS Node-RED™ UI IN THE GATEWAY

1. Attach the antenna to the Wzzard™ Mesh antenna port on the gateway.

2. Attach the Ethernet cable to the ETH0 port on the gateway and the other end to your PC.

You will use an Ethernet connection to configure the gateway and to communicate with it.

3. Attach the supplied power supply and plug it in.

4. Open a browser on your computer and open the Node-RED Configuration page. The default address is: 192.168.1.1:1880/ui. (Chrome or Firefox recommended.)

5. The Wzzard Node information values will populate when the node joins the network.

6. You can set up a phone number to receive text messages and/or an e-mail address for receiving alerts on this page. For text messaging, you will need to select the cell carrier of the receiving phone. If the carrier is not on the list, select custom, and add the URL of the carrier to the phone number (ie: [email protected]). See Appendix A for carrier text addresses. If your carrier is not listed, contact your carrier for the address of their

SMS gateway.

7. You can enable or disable alerts as well as setting the trigger values on this page also.

15

REFRIGERATION MONITORING KIT

NETWORK HEALTH PAGE

1. Click the Network Health button on the lower left corner of the Configuration page (see previous screen). The page below appears. This page shows the status of the network.

16

REFRIGERATION MONITORING KIT

ATTACHING THE SENSORS ON THE INTELLIGENT EDGE NODES

The Wzzard™ Mesh Refrigeration Monitoring Kit comes with built-in sensors for ambient temperature and humidity, along with two AC current sensors, a door switch, and a breakout cable with 10K thermistor.

1. Plug the Breakout/Thermistor Cable into the Molex connector on the bottom of the Wzzard

Mesh node.

2. Plug the door sensor into the 2-pin connector on the breakout cable.

3. Connect the sensors for compressor and fan current to the bare wires on the breakout cable.

Sensor Breakout Cable Connection

Sensor (+) to Stripped & Tinned Cable AIN1 RED

Compressor

Current

Sensor (-) to Stripped & Tinned Cable AIN1 BLACK

Fan

Current

Sensor (+) to Stripped & Tinned Cable AIN2 YELLOW

Sensor (-) to Stripped & Tinned Cable AIN2 BLACK

Current Sensors

1. Open the wire protector clamp by pushing it away from the sensor body.

2. Attach your wires.

3. Close the wire protector clamp.

17

REFRIGERATION MONITORING KIT

MOUNTING YOUR SENSORS

Current Sensors

The sensor can be mounted in any position.

1. Open the clamp release by pushing it away from the sensor body. Run the wire you are monitoring through the opening in the sensor.

2. Close the sensor firmly around your wire and ensure that the clamp release has snapped back into place.

18

REFRIGERATION MONITORING KIT

ACCESSING THE DASHBOARD

1. Open a browser on your computer and open the Node-RED™ Configuration page. The default address is: 192.168.1.1:1880/ui

2. Click on the Dashboard button on the lower left corner of the configuration page.

3. The dashboard should look like the following screen.

4. You can switch to the Configuration page or Network Health page by clicking on their respective buttons on the lower left.

19

SETTING UP AN E-MAIL ACCOUNT

REFRIGERATION MONITORING KIT

1. From your browser, open the Node-RED™ flow at 192.168.1.1:1880 .

2. Enter your user name and password. Default is:

Username: NodeRED

Password: 5mart5warm (set same as the SmartSwarm 342 password).

3. Find the green Send Email node on the right; double click on it.

20

REF_342

REFRIGERATION MONITORING KIT

3. Enter your UserID and Password for your e-mail server in the appropriate boxes.

(Leave the “To” field blank.)

NOTE: If you are using a G-Mail account, you will need to enable “Less Secure Apps” in the Google security settings. See below.

4. Click Done . Then click the Deploy button in the upper right corner of the page.

Note: Once you deploy the edited flow, you will have to re-enter any alert settings on the configuration screen of the dashboard.

21

REFRIGERATION MONITORING KIT

SETTING UP YOUR DROPBOX FOR LOGGING

1. Log in to your Dropbox account or sign up for a new one.

2. Once signed up or logged in:

• Go to https://www.dropbox.com/developers

• Click Create Your App box in the center of the screen.

• Select Dropbox API App .

• Choose an appropriate answer as to whether your node should be limited to its own folder or given full access. (TIP: This can be changed later, so select Yes to restrict the application while testing might be a good idea.)

• Choose an app name.

• Click Create App .

The subsequent app page will contain the App Key.

Save this string so you can enter it into the application later.

3. From your browser, open the Node-RED™ flow at 192.168.1.1:1880 .

4. Enter your user name and password. Default is:

Username: NodeRED

Password: 5mart5warm (set same as the SmartSwarm 342 password).

REF_342

5. Locate Log data to file , then scroll right to locate blue Write Local File node ; double click on it.

22

REF_342

REFRIGERATION MONITORING KIT

5. Then click on the pencil icon next to the Dropbox text window.

REF_342

6. Fill in the Access Token that you got from Dropbox. (See yellow box for more information.)

23

REFRIGERATION MONITORING KIT

7. Click Update; then Done again to close both windows.

8. Click the Deploy button in the upper right corner of the page.

NOTE: Once you deploy the edited flow, you will have to re-enter any alert settings on the Configuration screen of the Dashboard.

9. Enable logging on the dashboard web page.

24

REFRIGERATION MONITORING KIT

APPENDIX A. CARRIER TEXT MESSAGING URL ADDRESSES

U.S.A. Carriers

Alltel

AT&T (formerly Cingular)

Boost Mobile

Nextel (now Sprint Nextel)

Sprint PCS (now Sprint Nextel)

T-Mobile

US Cellular

Verizon

Virgin Mobile USA

[10-digit phone number]@message.alltel.com

Example: [email protected]

[10-digit phone number]@txt.att.net

[10-digit phone number]@cingularme.com

Example: [email protected]

[10-digit phone number]@myboostmobile.com

Example: [email protected]

[10-digit telephone number]@messaging.nextel.com

Example: [email protected]

[10-digit phone number]@messaging.sprintpcs.com

Example: [email protected]

[10-digit phone number]@tmomail.net

Example: [email protected]

[10-digit phone number]email.uscc.net (SMS)

Example: [email protected]

[10-digit phone number]@vtext.com

Example: [email protected]

[10-digit phone number]@vmobl.com

Example: [email protected]

International Carriers

7-11 Speakout (USA GSM)

Airtel (Karnataka, India)

Aql

AT&T Enterprise Paging

BigRedGiant Mobile Solutions

Email to SMS Gateway number @cingularme.com number

Airtel Wireless (Montana, USA) number @sms.airtelmontana.com

Alaska Communications Systems number @msg.acsalaska.com number @text.aql.com number

@airtelkk.com

@page.att.net number @tachyonsms.co.uk

Bell Mobility & Solo Mobile (Canada) number @txt.bell.ca

BPL Mobile (Mumbai, India) number @bplmobile.com

Cellular One (Dobson)

Cingular (Postpaid)

Centennial Wireless number @mobile.celloneusa.com number @cingularme.com number @cwemail.com

Cingular (GoPhone prepaid)

Claro (Brasil)

Claro (Nicaragua)

Comcel

Cricket [email protected] (SMS) number @clarotorpedo.com.br number number number

@ideasclaro-ca.com

@comcel.com.co

@sms.mycricket.com (SMS)

CTI

Emtel (Mauritius)

Fido (Canada)

General Communications Inc.

Globalstar (satellite) number @sms.ctimovil.com.ar number @emtelworld.net number number number

@fido.ca

@msg.gci.net

@msg.globalstarusa.com

25

Helio

Illinois Valley Cellular

Iridium (satellite)

Iusacell i wireless

Koodo Mobile (Canada)

LMT (Latvia)

Meteor (Ireland)

Mero Mobile (Nepal)

MetroPCS

Movicom (Argentina)

Mobitel (Sri Lanka)

Movistar (Colombia)

MTN (South Africa)

MTS (Canada)

Nextel (United States)

Nextel (Argentina)

Orange Polska (Poland)

Personal (Argentina)

Plus GSM (Poland)

President’s Choice (Canada)

Qwest

Rogers (Canada)

SL Interactive (Australia)

Sasktel (Canada)

Setar Mobile email (Aruba)

Suncom

T-Mobile (Austria)

T-Mobile (UK)

Telus Mobility (Canada)

Thumb Cellular

Tigo (Formerly Ola)

Tracfone (prepaid)

Unicel

Virgin Mobile (Canada)

Vodacom (South Africa)

Vodafone (Italy)

YCC

MobiPCS (Hawaii only)

REFRIGERATION MONITORING KIT number @messaging.sprintpcs.com number @ivctext.com number @msg.iridium.com number @rek2.com.mx number [email protected] number @msg.koodomobile.com number @sms.lmt.lv number @sms.mymeteor.ie

977number @sms.spicenepal.com number @mymetropcs.com number @sms.movistar.net.ar number @sms.mobitel.lk number @movistar.com.co number @sms.co.za number @text.mtsmobility.com number @messaging.nextel.com

TwoWay.11

number @nextel.net.ar

9digit @orange.pl number @alertas.personal.com.ar

+48 number @text.plusgsm.pl number @txt.bell.ca number @qwestmp.com number @pcs.rogers.com number @slinteractive.com.au number @sms.sasktel.com

297+number @mas.aw number @tms.suncom.com number @sms.t-mobile.at number @t-mobile.uk.net number @msg.telus.com number @sms.thumbcellular.com number @sms.tigo.com.co number @mmst5.tracfone.com number @utext.com number @vmobile.ca number @voda.co.za number @sms.vodafone.it number @sms.ycc.ru number @mobipcs.net

26

Node-RED™ SOFTWARE LICENSE

REFRIGERATION MONITORING KIT

Copyright (2019) (Advantech)

Node-RED is licensed under the Apache License, Version 2.0 (the "License"),

You may not use Node-RED software preinstalled in the SmartSwarm Gateway except in compli- ance with the License. You may obtain a copy of the License at: http://www.apache.org/licenses/LICENSE-2.0

Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.

See the License for the specific language governing permissions and limitations under the License.

27

ADVANTECH TECHNICAL SUPPORT

REFRIGERATION MONITORING KIT

1 (800) 346-3119 Phone:

Fax:

Email :

Web:

1 (815) 433-5109

Advantech Technical Support www.advantech.com

Documentation Number: pn2003BREF00_r1_BB-WSK-REF-2_1319m

28