advertisement
HD BaseT 1x4 Splitter
With EDID Control
User manual
Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference.
I.
Introduction
The Splitter is a tool for splitting and extending your HDMI signal over long distances to a compatible display. It is designed to convert HDMI signal to standard HD BaseT signal and transmit by Internet cable. It also supports Transfer Bidirectional Infrared control signal together with the HDMI signal, so you can control the Source in the Sink side which is 100 meters outside, also you can control the Sink in the
Source side which is 100 meters outside using the Splitter.
II.
Features
1.
Compliant with HDMI1.4, HDCP 1.2 and DVI 1.0.
2.
Full HD support: 1080p@60Hz@48 bit/pixels, 1080p@120Hz@24 bit/pixels, 3D 1080P60Hz and 4K x 2K@30Hz@24bit.
3.
Supports LPCM 7.1CH, Dolby True HD, and DTS-HD Master Audio.
4.
Operates for TMDS clock frequencies up to 300MHz.
5.
POE(Power Over Ethernet)function support, splitter powered
12V@5A, the 4 receivers don’t need power form the DC jack.
POE
Power Consumption less than 40W.
6.
Use single UTP LAN cable (CAT-5E/6) to substitute HDMI cable to achieve long distances transmission.
7.
UTP cable termination follows the standard of IEEE-568B.
8.
Transmission distance:
100 meters: 1080P @60Hz36bit; 3D1080P@30Hz36bit;
70 meters: 1080P @60Hz@48bit; 1080P @120Hz@24bit;
3D 1080P@60Hz@36bit; 4K x 2K@30Hz@24bit.
9.
Supports EDID control via EDID selector.
10.
Transfer Bidirectional Infrared control signal together with the
HDMI signal.
III.
Package
1.
HD BaseT Splitter -------------------------------------------------- 1PCS
2.
HD BaseT Receiver(HBT-E100 RX) ---------------------------- 4PCS
3.
Wideband IR Tx ---------------------------------------------------- 5PCS
4.
Wideband IR Rx ---------------------------------------------------- 5PCS
5.
12V5A DC Power Supply adapter ------------------------------ 1PCS
6.
Operation Manual ------------------------------------------------- 1PCS
IV.
Specifications
1.
Frequency Bandwidth 2.97Gbps
2.
HD BaseT Splitter Input/Output Ports 1x HDMI Female port/4 x CAT6
1x IR Transmitter/1x IR Receiver
3.
HD BaseT Receiver Input/Output Ports 1 x HDMI Female port/1 x CAT6
1x IR Transmitter/1x IR Receiver
4.
Power Supply DC 12V 5A
5.
ESD Protection Human Body Model: ± 8kV (air-gap discharge)
± 4kV (contact discharge)
6.
Dimensions (mm) Splitter: 115(W) X 270 (D) X 45 (H)
Receiver: 65(W) X 100 (D) X 25 (H)
1
7.
Weight Splitter: 900g
Receiver: 200g x 4
8.
Operating Temperature 0°C ~ 40°C / 32°F ~ 104°F
9.
Operating Temperature 0°C ~ 40°C / 32°F ~ 104°F
10.
Storage Temperature -20°C ~ 60°C / -4°F ~ 140°F
11.
Relative Humidity 20 ~ 90% RH (Non-condensing)
12.
Power Consumption (Max) 60W
V.
Operation controls and Functions
Splitter
1.
POWER SWITCH: Power ON\OFF Switch.
2.
POWER LED: This blue LED illuminate when the device is connected with power supply.
3.
IR IN: Supper IR Control System Over LAN Cable IR Receiver.
Source to SINK, plug Wideband IR Rx into this unit.
※ See the description 1.
4.
IR OUT: Supper IR Control System Over LAN Cable IR Transmitter
SINK to Source, plug Wideband IR Tx into this unit.
※ See the description 2.
5.
EDID Selector: Select output signal format via EDID Selector.
※ See the description 3.
6.
OUTPUT Area: Four RJ45 Jacks provide Standard HD BaseT signal output. Four red LED illuminate when the Receiver is connected with LAN cable.
7.
INPUT Area: HDMI Input port. Connect source with HDMI cable.
2
This red LED illuminate when the source is connected with HDMI cable.
8.
DC IN: Plug the 12V DC power supply into the unit.
Receiver
1.
DC IN: Power supply unit. In this system does not need the power.
2.
IR IN: Supper IR Control System Over LAN Cable IR Receiver. SINK to Source, plug Wideband IR Rx into this unit.
※ See the description 2.
3.
IR OUT: Supper IR Control System Over LAN Cable IR Transmitter.
Source to SINK, plug Wideband IR Tx into this unit.
※ See the description 1.
4.
HDMI OUT: HDMI Output port. Connect TV with HDMI cable.
5.
HDMI Signal IN: Standard HD BaseT signal input port.
6.
LINK LED: This red LED illuminate when the Splitter and Receiver is connected with LAN cable.
VI.
Application Example
3
※
Dscription 1
※
Dscription 2
4
※
Dcription 3
EDID Selector description as follow:
Number EDID Selector Description
1 0000 Copy OUTPUT 1
2
3
0001
0010
1080P,Stereo Audio 2.0
1080P,Dolby/DTS 5.1
4
5
6
7
8
0011
0100
0101
0110
0111
1080P,HD Audio 7.1
1080I,Stereo Audio 2.0
1080I,Dolby/DTS 5.1
1080I,HD Audio 7.1
3D,Stereo Audio 2.0
9
10
11
12
13
1000
1001
1010
1011
1100
3D,Dolby/DTS 5.1
3D,HD Audio 7.1
4K2K,Stereo Audio 2.0
4K2K,Dolby/DTS 5.1
4K2K,HD Audio 7.1
5
14
15
16
1101
1110
1111
Reserve
Reserve
Auto mode(default)
6
advertisement
Related manuals
advertisement