For GPD 515
Adjustable Frequency Drives
115 VAC Logic Interface
Part No. 46S03288-0010
DESCRIPTION
WARNING
The 115 VAC Logic Interface is an option for the GPD 515
drive. It allows the drive’s multi-function inputs (Run, Stop,
Jog, etc.) to be controlled by 115 Vac input signals. It mounts
directly to the drive’s control terminal strip.
OPERATIONAL SPECIFICATIONS
ON STATE
6.0 mA = ION
—
— VON
= 115 Vac
4.5 mA = IMIN ON —
— VMIN ON = 111 Vac
3.4 mA = IMAX OFF —
— VMAX OFF = 108 Vac
OFF STATE
0 —
mA
— 0
V
Hazardous voltage can cause severe injury or
death. Lock all power sources feeding drive in
"OFF position.
4. Loosen, but do not completely remove, the screws at drive
terminals 1 thru 8, 21, 22 and 23. Slide the option board onto
the drive terminal strip at these terminals. The wire hold down
clips should be on top of the option board. Securely tighten
the terminal screws. Attach the pigtail wire from the option
board to terminal 11 on the drive.
5. Connect external control signal wiring, using:
Figure 1. 2-Wire control (requires a maintained contact
for run, OR
Figure 2. 3-Wire control (requires a N.C. Stop push button
and a N.O. Run push button.)
NOTE
INSTALLATION
CAUTION
Option contains electrostatic sensitive devices. Personnel
should be grounded before removing carton contents and
installing into the equipment.
1. Turn off all power to the drive.
2. Remove drive front cover. Verify that CHARGE indicator
lamp inside drive is off.
The option board attaches to terminals 21, 22 and 23 only for
extra mounting support. THESE ARE NOT 115 Vac INPUTS!
Connection to these terminals should be made in accordance
with TM 4515 para. 5.31. Always terminate connections
between the wire hold down clip and the option board.
6. Replace drive front cover. Apply power to the drive.
Applying the specified AC signal between terminal C and any
of the option board terminals 1 thru 8 will now provide a low
impedance path (short) between terminal 11 and the
corresponding drive terminal (1 thru 8).
CAUTION
3. Use a voltmeter to verify that power has been
disconnected at incoming power terminals (L1, L2, L3).
CHANGE RECORD
1 STD-6824 10/21/96
2 STD-7004 1/22/97
Although it may function with triac outputs, this
option card is NOT intended to be controlled by a
triac output device or other electronic devices that
have a minimum load requirement or off state
leakage current associated with them.
DWG. NO. 02Y00025-0406
SHEET NO. 1 OF 2
REL. 4/9/96
( m - df )
Refer to Sheet 1 for latest change.
DWG. NO. 02Y00025-0406
SHEET NO. 2 OF 2
REL. 4/9/96
( m - df )
1
4
5
8
6
7
25
8
21
27
22
33
23
JOG SPEED
3SS *
4SS *
FWD RUN/STOP
REV RUN/STOP
1OL*
*
1
115 VAC
@ 60 HZ
PIGTAIL
LEAD
11
12
*
1
2
3
3
4
14
4
5
8
6
7
25
8
21
27
22
33
23
1SS *
2SS *
3SS *
RUN
STOP
1PB *
2PB *
*
1OL*
3PB *
EXT. FAULT
FWD/REV
AUTO/MANUAL
4SS *
ANGLE ENTRY TERMINALS
MAX. WIRE SIZE 16AWG
26
JOG SPEED
C
17
MULTI STEP SPEED
6 7
5
16
FAULT RESET
15
INDICATES COMPONENTS NOT SUPPLIED.
2
13
Figure 2 Interconnection For 3-Wire Control
1SS *
2SS *
1PB *
EXT. FAULT
AUTO/MANUAL
5SS *
6SS *
ANGLE ENTRY TERMINALS
MAX. WIRE SIZE 16AWG
26
BASE BLOCK
C
17
MULTI STEP SPEED
6 7
5
16
FAULT RESET
15
INDICATES COMPONENTS NOT SUPPLIED.
4
14
Figure 1 Interconnection For 2-Wire Control
*
3
1
2
3
2
13
FUNCTIONS SHOWN FOR TERMINALS 3 THRU 8 ARE THE DEFAULT FUNCTIONS
FOR 3-WIRE CONTROL. PARAMETER PROGRAMMING FOR H1-01 THRU H1-06
ALLOWS ASSIGNMENT OF OTHER FUNCTIONS TO THESE TERMINALS.
12
PART OF CONTROL
PC BOARD IN DRIVE
FUNCTIONS SHOWN FOR TERMINALS 3 THRU 8 ARE THE DEFAULT FUNCTIONS
FOR 2-WIRE CONTROL. PARAMETER PROGRAMMING FOR H1-01 THRU H1-06
ALLOWS ASSIGNMENT OF OTHER FUNCTIONS TO THESE TERMINALS.
115 VAC
@ 60 HZ
PIGTAIL
LEAD
11
PART OF CONTROL
PC BOARD IN DRIVE
">
