STMicroelectronics TL431 Datasheet

Z

TO-92

(Plastic package)

L

SOT23-5

L

SOT23-3

TL431

TL432

Automotive adjustable voltage reference

C

SOT323-6

Datasheet

-

production data

Applications

 Power supply

 Industrial

 Automotive

Description

The TL431 and TL432 are adjustable shunt voltage references with guaranteed temperature stability over the entire operating temperature range. The device temperature range is extended for the automotive version from -40 °C up to

+125 °C. The output voltage can be set to any value between 2.5 and 36 V with two external resistors. The TL431 and TL432 operate with a wide current range from 1 to 100 mA with a typical dynamic impedance of 0.22 Ω.

D

SO-8

(Batwing plastic micropackage)

Features

 AEC-Q100 qualified

 Adjustable output voltage: 2.5 to

36 V

 Sink current capability: 1 to 100 mA

 Typical output impedance: 0.22 Ω

 0.5% voltage precision only on the TL431B version

 1% and 2% voltage precision

 Automotive temp. range -40 °C to +125 °C

February 2021

This is information on a product in full production.

DocID4467 Rev 15 1/22 www.st.com

5

6

1

2

3

Contents

Contents

4

TL431, TL432

Schematic diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 4

Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Reference input voltage deviation overtemperature range . . . . . . . . . . . . . . . . . . . 8

Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.1

SO-8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.2

TO-92 ammopack and tape and reel package information . . . . . . . . . . . 14

4.3

TO-92 (bulk) package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.4

SOT23-3 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

4.5

SOT23-5 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.6

SOT323-6 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2/22 DocID4467 Rev 15

TL431, TL432

1 Schematic diagrams

Figure 1. TO-92 pin connections (top view)

Schematic diagrams

Figure 2. SO-8 batwing pin connections (top view)

SO8

Cathode 1 8 Ref

Anode 2

3

NC 4

7 Anode

6

5 NC

NC

NC

Cathode 3

1

2

Figure 3. SOT23-5 and SOT23-3 pin connections (top view)

SOT23-5 SOT23-3

5 Anode Cathode 1

4 Ref Ref 2 3 Anode

TL431 TL431 TL432

Figure 4. SOT323-6 pin connections (top view)

Figure 5. TL431 and TL432 block diagram

Cathode

Ref

Vref

Anode

DocID4467 Rev 15 3/22

22

Absolute maximum ratings and operating conditions

2

TL431, TL432

Absolute maximum ratings and operating conditions

Symbol

Table 1. Absolute maximum ratings

Parameter Value Unit

V

I

R

R

T

I ref thjc thja stg

T

KA k

J

ESD

Cathode to anode voltage

Continuous cathode current range

Reference input current range

Thermal resistance junction to case

TO-92

SO-8 batwing

SOT23-3L

SOT23-5L

SOT323-6L

Thermal resistance junction to ambient

TO-92

SO-8 batwing

SOT23-3L

SOT23-5L

SOT323-6L

Storage temperature range

Junction temperature

TL431IY, TL431AIY-T: HBM (human body model)

(1)

TL431-TL432: HBM (human body model)

MM: machine model

(2)

CDM: charged device model

(3)

37

-100 to +150

-0.05 to +10

57

30

136

67

110

200

85

248

157

221

-65 to +150

150

3000

2000

200

1500

V mA mA

°C/W

°C/W

°C

°C

V

1. Human body model: a 100 pF capacitor is charged to the specified voltage, then discharged through a

1.5 k  resistor between two pins of the device. This is done for all couples of connected pin combinations while the other pins are floating.

2. Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5  ). This is done for all couples of connected pin combinations while the other pins are floating.

3. Charged device model: all pins and the package are charged together to the specified voltage and then discharged directly to the ground through only one pin. This is done for all pins.

Symbol

V

KA

I k

T oper

Table 2. Operating conditions

Parameter

Cathode to anode voltage

Cathode current

Operating free-air temperature range

TL431C/AC

TL431I/AI - TL432I/AI

TL431B

TL431IY/AIY

Value

V ref

to 36

1 to 100

0 to +70

-40 to +105

-40 to +125

-40 to +125

Unit

V mA

°C

4/22 DocID4467 Rev 15

TL431, TL432

3 Electrical characteristics

Electrical characteristics

Symbol

V ref

 V ref

I ref

Table 3. TL431C (T amb

= 25 °C unless otherwise specified)

TL431C

Parameter

TL431AC

Min.

Typ. Max. Min.

Typ. Max.

Unit

Reference input voltage

V

KA

T min

= V ref

, I k

= 10 mA, T amb

= 25 °C

  T amb

 T max

Reference input voltage deviation overtemperature range

(1)

V

KA

= V ref

, I k

= 10 mA, T min

  T amb

 T max

Ratio of change in reference input voltage to change in cathode to anode voltage

I k



= 10 mA -  V

KA

V

KA

= 10 V to V

= 36 V to 10 V ref

2.44

2.423

2.495

-

2.55

2.567

2.47

2.453

2.495

-

2.52

2.537

-

-2.7

-2

3

-1.4

-1

17

-

-

-

-2.7

-2

3

-1.4

-1

15

-

-

V mV mV/V

I

Reference input current k

= 10 mA, R1 = 10 k  , R2 = 

T amb

T min

= 25 °C

  T amb

  T max

-

-

1.8

-

4

5.2

-

-

1.8

-

4

5.2

µA

 I ref

Reference input current deviation overtemperature range

I k

T

= 10 mA, R1 = 10 k  , R2 =  min

  T amb

 T max

0.4 1.2

I min

I off

 ZKA 

Minimum cathode current for regulation

V

KA

= V ref

Off-state cathode current

Dynamic impedance

(2)

V

KA

= V ref

,  I k

= 1 to 100 mA, f  1 kHZ -

-

-

0.5

1

2.6

1000

0.22

0.5

1. See definition of

Section : Reference input voltage deviation overtemperature range

.

2. The dynamic impedance is defined as



ZKA



 =

 V

 I k

-

-

-

0.4

1.2

0.5

0.6

mA

2.6

1000 nA

0.22

0.5

µA



DocID4467 Rev 15 5/22

22

Electrical characteristics TL431, TL432

Symbol

V ref

 V ref

 Vka

I ref

Table 4. TL431B (T amb

= 25 °C unless otherwise specified)

TL431B

Parameter

Min.

Typ.

Max.

Reference input voltage

V

KA

T min

= V

  T ref

, I k

= 10 mA, T amb

= 25 °C amb

 T max

2.483

2.453

2.495

-

2.507

2.537

Reference input voltage deviation overtemperature range

(1)

V

KA

= V ref

, I k

= 10 mA, T min

  T amb

 T max

7 30

Ratio of change in reference input voltage to change in cathode to anode voltage

I k



= 10 mA -  V

KA

V

KA

= 10 V to V

= 36 V to 10 V ref

I

Reference input current k

= 10 mA, R1 = 10 k  , R2 = 

T amb

T min

= 25 °C

  T amb

  T max

-2.7

-2

-

-

-1.4

-1

1.8

-

-

-

4

6.5

Unit

V mV mV/V

µA

 I ref

Reference input current deviation overtemperature range

I k

T

= 10 mA, R1 = 10 k  , R2 =  min

  T amb

 T max

I min

I off

 ZKA 

Minimum cathode current for regulation

V

KA

= V ref

Off-state cathode current

Dynamic impedance

(2)

V

KA

= V ref

,  I k

= 1 to 100 mA, f  1 kHZ

1. See definition of Section : Reference input voltage deviation overtemperature range

.

2. The dynamic impedance is defined as



ZKA



 =

 V

 I k

-

-

-

-

0.8

0.45

180

0.22

2.5

0.6

500

0.5

µA mA nA



6/22 DocID4467 Rev 15

TL431, TL432 Electrical characteristics

Symbol

V ref

 V ref

Table 5. TL431I/TL432I (T amb

= 25 °C unless otherwise specified)

TL431I/TL432I TL431AI/TL432AI

Parameter

Min.

Typ. Max. Min.

Typ. Max.

Reference input voltage

V

KA

T min

= V ref

, I k

  T amb

= 10 mA, T amb

= 25 °C

 T max

Reference input voltage deviation overtemperature range

(1)

V

KA

= V ref

, I k

=10 mA, T min

  T amb

 T max

Ratio of change in reference input voltage to change in cathode to anode voltage

I k



= 10 mA,  V

KA

V

KA

= 10 V to V ref

= 36 V to 10 V

2.44

2.41

2.495

-

2.55

2.58

-

-2.7

-2

7

-1.4

-1

30

-

-

2.47

2.44

2.495

-

2.52

2.55

-

-2.7

-2

7

-1.4

-1

30

-

-

Unit

V mV mV/V

I ref

I

Reference input current k

= 10 mA, R1 = 10 k  , R2 = 

T amb

T min

= 25 °C

  T amb

 T max

-

1.8

-

4

6.5

 I ref

I min

I off

 ZKA 

Reference input current deviation overtemperature range

I k

T

= 10 mA, R1 = 10 k  , R2 =  min

  T amb

 T max

Minimum cathode current for regulation

V

KA

= V ref

Off-state cathode current

Dynamic impedance

(2)

V

KA

= V ref

,  I k

= 1 to 100 mA, f   1 kHZ

-

-

-

0.8

2.5

0.5

1

2.6

1000

0.22

0.5

1. See definition of Section : Reference input voltage deviation overtemperature range

below.

2. The dynamic impedance is defined as



ZKA



 =

 V

 I k

-

-

-

-

-

-

1.8

-

4

6.5

0.8

1.2

0.5

0.7

mA

2.6

1000 nA

0.22

0.5

µA

µA



DocID4467 Rev 15 7/22

22

Electrical characteristics TL431, TL432

Symbol

Table 6. TL431IY (T amb

= 25 °C unless otherwise specified)

TL431IY TL431AIY

Parameter

Min.

Typ. Max. Min.

Typ. Max.

V ref

 V ref

Reference input voltage

V

KA

T min

= V ref

, I k

  T amb

= 10 mA

 T max

Reference input voltage deviation overtemperature range

(1)

V

KA

= V ref

, I k

= 10 mA, T min

  T amb

 T max

Ratio of change in reference input voltage to change in cathode to anode voltage

I k

I k

= 10 mA,  V

KA

= 10 mA,  V

KA

= 10 V to V ref

= 36 V to 10 V

2.44

2.41

-

2.495

-

7

2.55

2.58

30

-2.7

-2

-1.4

-1 -

-

I ref

 I ref

I min

I off

 ZKA 

Reference input current

I k

= 10 mA, R1 = 10 k  , R2 = 

T min

  T amb

 T max

Reference input current deviation overtemperature range

I k

= 10 mA, R1 = 10 k

T max

 , R2 =  T min

  T amb



Minimum cathode current for regulation

V

KA

= V ref

Off-state cathode current

T min

  T amb

 T max

Dynamic impedance (2)

V

KA

= V ref

,  I k

= 1 to 100 mA, F   1 kHz

-

-

-

-

-

-

-

1.8

-

0.5

4

6.5

0.8

2.5

1

2.6

1000

3000

0.22

0.5

1. See definition of Section : Reference input voltage deviation overtemperature range

below.

2. The dynamic impedance is defined as



ZKA



 =

 V

 I k

2.47

2.44

2.495

-

2.52

2.55

-2.7

-2

-

-

-

-

-

-

-

-

7

-1.4

-1

1.8

-

30

-

-

4

6.5

0.8

1.2

0.5

0.6

mA

2.6

1000

3000

0.22

0.5

Unit

V mV mV/V

µA

µA nA



Reference input voltage deviation overtemperature range

 V ref

is defined as the difference between the maximum and minimum values obtained over the full temperature range.



V ref

= V ref max

- V ref min

Figure 6. Reference input voltage deviation overtemperature range

8/22 DocID4467 Rev 15

TL431, TL432 Electrical characteristics

Input

Figure 7. Test circuit for V

KA

= V ref

R

I

K

=10mA

Output

Figure 8. Test circuit for programming mode

Input R Output

I

K

R1

I

REF V

KA

V

KA

R2

V

REF

V

REF

V

KA

= V

REF

 

+ R1 x I

REF

Figure 9. Test circuit for I off

V

KA

=36V

I

OFF

Figure 10. Test circuit for phase margin and voltage gain

10  F

I

K

=10mA

10  F

Input

V

REF

Figure 11. Test circuit for response time

0 mA

1 mA

I

K

=1mA

Figure 12. Reference voltage vs. temperature

2.54

2.52

2.50

I

V

K

KA

= V

REF

= 10 mA

2.48

2.46

2.44

-40 -20 0 20 40 60

Temperature (  C)

80 100 120

DocID4467 Rev 15 9/22

22

Electrical characteristics

Figure 13. Reference voltage vs. cathode current

TL431, TL432

Figure 14. Zoom on reference voltage vs. cathode current

Figure 15. Reference current vs. temperature

2.0

1.5

I

K

=10 mA

R

1

=10k 

R2= + 

1.0

0.5

0.0

-40 -20 0 20 40 60

Temperature °C

80 100 120

Figure 17. Ratio of change in V

V

KA ref

to change in

vs. temperature

0.0

-0.5

-1.0

-1.5

I

K

= 10 mA

-2.0

-40 -20 0 20 40 60

Temperature (  C)

80 100 120

Figure 16. Off-state cathode current vs. temperature

0.4

V

KA

= 36 V

V

REF

= 0 V

0.3

0.2

0.1

0.0

-40 -20 0 20 40 60

Temperature (  C)

80 100 120

Figure 18. Static impedance R

KA temperature

vs.

0.20

0.18

V

KA

=V

REF

0.16

0.14

0.12

0.10

-40 -20 0 20 40 60

Temperature (  C)

80 100 120

10/22 DocID4467 Rev 15

TL431, TL432

Figure 19. Minimum operating current vs. temperature

0.6

Electrical characteristics

Figure 20. Gain and phase vs. frequency

0.4

0.2

V

KA

= V

REF

0.0

-40 -20 0 20 40 60

Temperature (  C)

80 100 120

Figure 21. Stability behavior with capacitive loads

Figure 22. Maximum power dissipation

Figure 23. Pulse response for I k

= 1 mA

DocID4467 Rev 15 11/22

22

Package information

4 Package information

TL431, TL432

In order to meet environmental requirements, ST offers these devices in different grades of

ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com

.

ECOPACK is an ST trademark.

12/22 DocID4467 Rev 15

TL431, TL432

4.1 SO-8 package information

Figure 24. SO-8 package outline

Package information

Symbol

L

L1 e h k ccc c

D

E

E1

A

A1

A2 b

-

0.25

0.40

-

0°

-

0.10

1.25

0.28

0.17

4.80

5.80

3.80

Min.

Table 7. SO-8 package mechanical data

Dimensions

Millimeters

Typ.

1.27

-

-

1.04

-

-

-

4.90

6.00

3.90

-

-

-

-

Max.

-

0.50

1.27

-

8°

0.10

0.23

5.00

6.20

4.00

1.75

0.25

-

0.48

Min.

-

0.010

0.016

-

0°

-

-

0.004

0.049

0.011

0.007

0.189

0.228

0.150

Inches

Typ.

0.050

-

-

0.040

-

-

-

0.193

0.236

0.154

-

-

-

-

Max.

-

0.020

0.050

-

8°

0.004

0.069

0.010

-

0.019

0.010

0.197

0.244

0.157

DocID4467 Rev 15 13/22

22

Package information

4.2

TL431, TL432

TO-92 ammopack and tape and reel package information

Figure 25. TO-92 ammopack and tape and reel package outline

14/22

Table 8. TO-92 ammopack and tape and reel package mechanical data

Dimension (millimeters)

Symbol

Dimension (Inches)

Min.

Typ.

Max.

Min.

Typ.

Max.

-

-

5.7

8.5

2.4

-1

-1

17.5

15.5

-

3.8

-

2.5

11.7

12.4

5.95

-

-

-

-

H0

H1

DO

L1

W0

W1

W2

H

I1

P

PO

P2

F1/F2

 h

 P

W

T d

A1

A

-

-

6

9

2.5

0

0

18.0

16

-

4.0

-

-

12.7

12.7

6.35

-

-

-

0.45

6.3

9.75

0.5

20

2.8

1

1

19.0

16.5

25

4.2

11

-

13.7

13

6.75

5.0

5.0

4.0

-

0.094

-0.039

-0.039

0.689

0.224

0.335

-

-

0.098

0.461

0.488

0.234

-

-

-

-

0.610

-

0.150

-

0.098

0

0

0.709

0.236

0.354

-

-

-

-

-

0.018

-

0.500

0.500

0.250

0.630

-

0.157

-

0.110

0.039

0.039

0.748

0.248

0.384

0.020

0.787

0.197

0.197

0.157

-

-

0.539

0.512

0.266

0.650

0.984

0.165

0.433

DocID4467 Rev 15

TL431, TL432

4.3 TO-92 (bulk) package information

Figure 26. TO-92 bulk package outline

Package information

Symbol

E

F a

C

D

A

B

0067407_H

Min.

-

-

-

4.40

12.70

-

-

Table 9. TO-92 bulk package mechanical data

Dimension (millimeters) Dimension (Inches)

Typ.

-

-

-

1.35

-

2.54

-

Max.

-

4.70

-

-

-

3.70

0.5

Min.

-

-

-

0.173

0.500

-

-

Typ.

-

-

-

0.053

-

0.100

-

Max.

-

0.185

-

-

-

0.146

0.019

DocID4467 Rev 15 15/22

22

Package information

4.4 SOT23-3 package information

Figure 27. SOT23-3 package outline

TL431, TL432

16/22

Symbol c

D

E

E1

A

A1

A2 b e e1

L

L1 k

Min.

0.08

2.80

2.10

1.20

0.89

0.01

0.88

0.30

-

-

0.40

-

0d

Table 10. SOT23-3 package mechanical data

Dimensions

Millimeters

Typ.

-

2.90

-

1.30

-

-

0.95

-

0.95

1.90

0.50

0.54

-

Max.

0.20

3.04

2.64

1.40

1.12

0.10

1.02

0.50

-

-

0.60

-

8d

Min.

0.035

0.0004

0.035

0.012

0.003

0.110

0.083

0.047

0.016

-

-

-

-

Inches

Typ.

-

-

0.037

-

-

0.114

-

0.051

0.037

0.075

0.020

0.021

-

Max.

0.044

0.004

0.040

0.020

0.008

0.120

0.104

0.055

0.024

-

-

-

-

DocID4467 Rev 15

TL431, TL432

4.5 SOT23-5 package information

Figure 28. SOT23-5 package outline

Package information

L

 c

D

E e

H

A

A1

A2 b

Symbol

7049676_I

Min.

0.90

-

0.90

0.35

0.09

2.80

1.50

-

2.60

0.10

0 degrees

Table 11. SOT23-5 package mechanical data

Dimensions

Millimeters Inches

Typ.

-

-

-

-

-

-

-

0.95

-

-

-

Max.

1.45

0.15

1.30

0.50

0.20

3.05

1.75

-

3.00

0.60

10 degrees

Min.

0.035

-

0.035

0.014

0.004

0.110

0.059

-

0.102

0.004

-

Typ.

-

-

-

-

-

-

-

0.037

-

-

-

Max.

0.057

0.006

0.051

0.020

0.008

0.120

0.069

-

0.118

0.024

-

DocID4467 Rev 15 17/22

22

Package information

4.6 SOT323-6 package information

Figure 29. SOT323-6 package outline

TL431, TL432

18/22

Symbol

D

E e b c

A

A1

A2

HE

L

Q1

7095021_E

Min.

0.80

0

0.80

0.15

0.10

1.80

1.15

-

1.80

0.10

0.10

Table 12. SOT323-6 package mechanical data

Dimensions

Millimeters

Typ.

-

-

-

-

0.65

-

-

-

-

-

-

Max.

1.10

0.10

1.00

0.30

0.18

2.20

1.35

-

2.40

0.40

0.40

Min.

0.031

-

0.031

0.006

0.004

0.071

0.045

-

0.071

0.004

0.004

Inches

Typ.

-

-

-

-

-

-

-

-

-

-

0.026

DocID4467 Rev 15

Max.

0.043

0.004

0.039

0.012

0.007

0.087

0.053

-

0.094

0.016

0.016

TL431, TL432

5 Ordering information

Order code

TL431AIZ

TL431AIZT

TL431AIZ-AP

TL431IL3T

TL431AIL3T

TL432IL3T

TL432AIL3T

TL431IL5T

TL431AIL5T

TL431ICT

TL431AICT

TL431BL3T

TL431CD

TL431CDT

TL431ACD

TL431ACDT

TL431CZ

TL431CZT

TL431CZ-AP

TL431ACZ

TL431ACZT

TL431ACZ-AP

TL431CL3T

TL431ACL3T

TL431CL5T

TL431ACL5T

TL431CCT

TL431ACCT

TL431ID

TL431IDT

TL431AID

TL431AIDT

TL431IZ

TL431IZT

TL431IZ-AP

Table 13. Order codes

Accuracy (%) Temperature range Package

2

SO-8

1

2

1

1

2

1

2

1

2

2

1

2

1

2

1

2

1

2

2

1

1

0.5

0 °C to +70 °C

-40 °C to +105 °C

-40 °C to +125 °C

TO-92

SOT23-3

SOT23-5

SOT323-6

SO-8

TO-92

SOT23-3

SOT23-3

SOT23-5

SOT323-6

SOT23-3

Ordering information

Packing

Tube or

Tape and reel

Marking

431C

431AC

TL431C

Bulk or

Tape or

Ammopack

Tape

Tube or tape and reel

TL431AC

L19

L18

L19

L18

31C

31C

431I

431AI

TL431I

Bulk or

Tape or

Ammopack

Tape

TL431AI

L17

L16

32I

32AI

L17

L16

31I

31I

1B

DocID4467 Rev 15 19/22

22

Ordering information TL431, TL432

Order code

TL431IYD (1)

TL431IYDT

(1)

TL431AIYD (1)

TL431AIYDT

(1)

2

1

Table 13. Order codes (continued)

Accuracy (%) Temperature range

-40 °C to +125 °C

Package

SO-8

(Automotive grade level)

Packing

Tube or tape and reel

Marking

431IY

431AIY

1. Qualification and characterization according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC

Q001 and Q 002 or equivalent.

20/22 DocID4467 Rev 15

TL431, TL432

6 Revision history

Date

01-Mar-2002

01-Nov-2005

13-Dec-2006

08-Jun-2007

25-Feb-2008

04-Jun-2009

09-Jun-2009

14-Mar-2011

07-Oct-2011

17-Nov-2011

03-Dec-2012

07-Dec-2017

10-Sep-2020

23-Sep-2020

08-Feb-2021

Revision history

Revision

1

2

3

4

5

6

13

14

15

7

8

9

10

11

12

Table 14. Document revision history

Changes

Initial release.

PPAP references inserted in order codes table on cover page.

Corrected TO-92 package information.

Specified that SO-8 package is batwing package.

In electrical characteristics tables, moved negative values from max column to min column.

Corrected captions of

Figure 7

and of

Figure 18

.

Added footnote to Table 8: TO-92 bulk package mechanical data .

Corrected SO-8 package mechanical data.

Corrected footnote for automotive grade order codes in order code table.

Corrected packing information for TO-92 devices in order code table.

Changed I

MIN

to 0.6 mA in Table 3 and Table 4 .

Increased temperature range to 125°C in temperature curves.

Added

Table 5

, dedicated to automotive version.

Increased high temperature for automotive range up to +125 °C in Table 5 and in

Table 12: Order codes

.

Inserted accuracy column in Table 12 .

Corrected minor error in package column in

Table 12

.

Added

Figure 3 on page 3

,

Section 4.4 on page 15

and

Section 4.5 on page

16

.

Added new package mechanical data Table 11 on page 17 and Figure 29 on page 17

.

Updated Table 12 on page 18 .

Added new part number TL432, new order code

Table 12 on page 18

and pin connection for TL432 Figure 3 on page 3 .

Removed temperature range in title

Table 3 on page 5

,

Table 4 on page 6

and

Table 5 on page 7

.

Updated main title

on page 1

and

Section : Features on page 1

, (added

“automotive” - AEC-Q100 qualified).

Updated

Table 1 on page 4

(updated R thja and R thjc

).

Minor modifications throughout document.

Added the part number TL431B and all its occurrences throughout the document.

Updated Table 4: TL431B (Tamb = 25 °C unless otherwise specified).

Updated

Table 13: Order codes

.

DocID4467 Rev 15 21/22

22

TL431, TL432

IMPORTANT NOTICE – PLEASE READ CAREFULLY

STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on

ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.

Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products.

No license, express or implied, to any intellectual property right is granted by ST herein.

Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.

ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to www.st.com/trademarks .  All other product or service names are the property of their respective owners.

Information in this document supersedes and replaces information previously supplied in any prior versions of this document.

© 2021 STMicroelectronics – All rights reserved

22/22 DocID4467 Rev 15