TL082, TL082A, TL082B
General purpose JFET dual operation amplifiers
Datasheet - production data
Description
The TL082, TL082A and TL082B are high speed
JFET input dual operational amplifiers incorporating well-matched, high voltage JFET and bipolar transistors in a monolithic integrated circuit.
The devices feature high slew rates, low input bias and offset current, and low offset voltage temperature coefficient.
Features
Wide common-mode (up to V
CC
+ ) and differential voltage range
Low input bias and offset current
Output short-circuit protection
High input impedance JFET input stage
Internal frequency compensation
Latch up free operation
High slew rate: 16 V/µs (typical)
June 2016 DocID2300 Rev 11
This is information on a product in full production.
1/18 www.st.com
Contents TL082, TL082A, TL082B
Contents
1 Schematic diagram .......................................................................... 3
2 Pin connections ............................................................................... 4
3 Absolute maximum ratings and operating conditions ................. 5
4 Electrical characteristics ................................................................ 6
5 Electrical characteristic curves ...................................................... 8
6 Parameter measurement information .......................................... 11
7 Typical applications ...................................................................... 12
8 Package information ..................................................................... 13
8.1
8.2
SO8 package information ................................................................ 14
TSSOP8 package information ......................................................... 15
9 Ordering information ..................................................................... 16
10 Revision history ............................................................................ 17
2/18 DocID2300 Rev 11
TL082, TL082A, TL082B
1 Schematic diagram
Figure 1: Schematic diagram
Schematic diagram
DocID2300 Rev 11 3/18
Pin connections
2 Pin connections
Figure 2: Pin connections (top view)
TL082, TL082A, TL082B
4/18 DocID2300 Rev 11
TL082, TL082A, TL082B
3
Absolute maximum ratings and operating conditions
Absolute maximum ratings and operating conditions
Symbol
V
V
V
P
CC in id tot
Table 1: Absolute maximum ratings
Parameter TL082I, AI, BI TL082C, AC, BC Unit
Supply voltage (1)
Input voltage (2)
Differential input voltage (3)
Power dissipation
±18
±15
±30
680
V mW
R
R
T thja thjc stg
ESD
Thermal resistance
junction-to-ambient (4)
Thermal resistance junction-to-case
Output short-circuit duration
Storage temperature range
HBM: human body model (6)
MM: machine model (7)
(5)
CDM: charged device model (8)
SO8
TSSOP8
SO8
TSSOP8
125
120
40
37
Infinite
-65 to 150
1
200
1500
°C/W
°C kV
V
Notes:
(1)
All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the zero reference level is the midpoint between V
CC
+
and V
CC
-
.
(2)
The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less.
(3)
Differential voltages are the non-inverting input terminal with respect to the inverting input terminal.
(4)
Short-circuits can cause excessive heating. Destructive dissipation can result from simultaneous short-circuit on all amplifiers.
(5)
The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded
(6)
Human body model: 100 pF discharged through a 1.5 kΩ resistor between two pins of the device, done for all couples of pin combinations with other pins floating.
(7)
Machine model: a 200 pF cap is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5 Ω), done for all couples of pin combinations with other pins floating.
(8)
Charged device model: all pins plus package are charged together to the specified voltage and then discharged directly to the ground.
Symbol
Table 2: Operating conditions
Parameter TL082I, AI, BI TL082C, AC, BC Unit
V
CC
T oper
Supply voltage
Operating free-air temperature range -40 to 105
6 to 36
0 to 70
V
°C
DocID2300 Rev 11 5/18
Electrical characteristics TL082, TL082A, TL082B
4 Electrical characteristics
Symbol
I ib
A vd
Table 3: VCC = ±15V, Tamb = +25°C (unless otherwise specified)
TL082I, AC, AI, BC, BI TL082C
Parameter
Min. Typ. Max. Min. Typ. Max.
V io
Input offset voltage, R s
= 50 Ω,
T amb
= 25 °C, TL082
Input offset voltage, R s
= 50 Ω,
T amb
= 25 °C, TL082A
Input offset voltage, R s
= 50 Ω,
T amb
= 25 °C, TL082B
Input offset voltage, R s
= 50 Ω,
T min
≤ T amb
≤ T max
, TL082
Input offset voltage, R s
= 50 Ω,
T min
≤ T amb
≤ T max
, TL082A
Input offset voltage, R s
= 50 Ω,
T min
≤ T amb
≤ T max
, TL082B
DV io
Input offset voltage drift
I io
Input offset current, T amb
= 25 °C (1)
Input offset current, T min
≤ T amb
≤ T
max
(1)
Input bias current, T amb
= 25 °C
Input bias current, T min
≤ T amb
≤ T
Large signal voltage gain,
R
L
= 2 kΩ, V max o
= ±10 V, T amb
= 25 °C
Large signal voltage gain,
R
L
= 2 kΩ, V o
= ±10 V, T min
≤ T amb
≤ T max
Supply voltage rejection ratio,
R
S
= 50 Ω, T amb
= 25 °C
50
25
3
3
1
10
5
20
200
10
6
3
13
7
5
100
4
200
20
15
3 10
13
10
5 100
10
20 400
20
25 200
SVR
80 86 70 86
I
V
CC icm
Supply voltage rejection ratio,
R
S
= 50 Ω, T min
≤ T amb
≤ T max
Supply current, no load, T amb
= 25 °C
Supply current, no load, T min
≤ T amb
≤ T max
Input common mode voltage range
80
±11
1.4
15
-12
2.5
2.5
70
±11
1.4
15
-12
2.5
2.5
CMR
I os
Common mode rejection ratio,
R
S
= 50 Ω, T amb
= 25 °C
Common mode rejection ratio,
R
S
= 50 Ω, T min
≤ T amb
≤ T max
Output short-circuit current,
T amb
= 25 °C
Output short-circuit current,
T min
≤ T amb
≤ T max
80
80
10
10
86
40 60
60
70
70
10
10
86
40 60
60
Unit mV
µV/°C pA nA pA nA
V/mV dB mA
V dB mA
6/18 DocID2300 Rev 11
TL082, TL082A, TL082B Electrical characteristics
TL082I, AC, AI, BC, BI TL082C
Symbol Parameter Unit
Min. Typ. Max. Min. Typ. Max.
Output voltage swing,
T amb
= 25 °C, R
L
= 2 kΩ
10 12 10 12
Output voltage swing,
T amb
= 25 °C, R
L
= 10 kΩ
12 13.5 12 13.5
±V opp
V
Output voltage swing,
T min
≤ T amb
≤ T max
, R
L
= 2 kΩ
10 10
Output voltage swing,
T min
≤ T amb
≤ T max
, R
L
= 10 kΩ
12 12
SR
Slew rate, T amb
= 25 °C, V in
= 10 V,
R
L
= 2 kΩ, C
L
= 100 pF, unity gain
8 16 8 16 V/µs t r
Rise time, T amb
= 25 °C, V in
= 20 mV,
R
L
= 2 kΩ, C
L
= 100 pF, unity gain
0.1 0.1 µs
K ov
Overshoot, T amb
= 25 °C, V in
= 20 mV,
R
L
= 2 kΩ, C
L
= 100 pF, unity gain
10 10 %
GBP
Gain bandwidth product, T amb
= 25 °C,
V in
= 10 mV, R
L
= 2 kΩ, C
L
= 100 pF,
F = 100 kHz
2.5 4 2.5 4 MHz
R i
Input resistance
THD e n
Total harmonic distortion, T amb
= 25 °C,
F = 1 kHz, R
L
= 2 kΩ, C
L
= 100 pF,
A v
= 20 dB, V o
= 2 V pp
Equivalent input noise voltage, R
S
= 100 Ω,
F = 1 kHz
∅ m Phase margin
V o1
/V o2
Channel separation, A v
= 100
10 12
0.01
15
45
120
10 12
0.01
15
45
120
Notes:
(1)
The input bias currents are junction leakage currents which approximately double for every 10° C increase in the junction temperature.
Ω
% nV/√Hz degrees dB
DocID2300 Rev 11 7/18
Electrical characteristic curves TL082, TL082A, TL082B
5 Electrical characteristic curves
Figure 3: Maximum peak-to-peak output voltage versus frequency
Figure 4: Maximum peak-to-peak output voltage versus frequency
Figure 5: Maximum peak-to-peak output voltage versus load resistance
Figure 6: Maximum peak-to-peak output voltage versus frequency
Figure 7: Maximum peak-to-peak output voltage versus free air temperature
Figure 8: Maximum peak-to-peak output voltage versus supply voltage
8/18 DocID2300 Rev 11
TL082, TL082A, TL082B
Figure 9: Input bias current versus free air temperature
Electrical characteristic curves
Figure 10: Large signal differential voltage amplification and phase shift versus frequency
Figure 11: Supply current per amplifier versus free air temperature
Figure 12: Large signal differential voltage amplification versus free air temperature
Figure 13: Total power dissipation versus free air temperature
Figure 14: Supply current per amplifier versus supply voltage
DocID2300 Rev 11 9/18
Electrical characteristic curves
Figure 15: Common-mode rejection ratio versus free air temperature
TL082, TL082A, TL082B
Figure 16: Output voltage versus elapsed time
Figure 17: Voltage follower large signal pulse response Figure 18: Equivalent input noise voltage versus frequency
Figure 19: Total harmonic distortion versus frequency
10/18 DocID2300 Rev 11
TL082, TL082A, TL082B
6
Parameter measurement information
Parameter measurement information
Figure 20: Voltage follower
Figure 21: Gain-of-10 inverting amplifier
DocID2300 Rev 11 11/18
Typical applications
7 Typical applications
Figure 22: 100 kHz quadruple oscillator
TL082, TL082A, TL082B
1. These resistor values may be adjusted for a symmetrical output
12/18 DocID2300 Rev 11
TL082, TL082A, TL082B
8 Package information
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK ® packages, depending on their level of environmental compliance. ECOPACK ® specifications, grade definitions and product status are available at: www.st.com
.
ECOPACK ® is an ST trademark.
DocID2300 Rev 11 13/18
Package information
8.1 SO8 package information
Figure 23: SO8 package outline
TL082, TL082A, TL082B
14/18
Ref.
L
L1 k ccc
E
E1 e h
A
A1
A2 b c
D
Min.
0.10
1.25
0.28
0.17
4.80
5.80
3.80
0.25
0.40
1°
Table 4: SO8 mechanical data
Dimensions
Millimeters
Typ. Min. Max.
1.75
0.25
4.90
6.00
3.90
1.27
0.48
0.23
5.00
6.20
4.00
0.50
1.27
0.004
0.049
0.011
0.007
0.189
0.228
0.150
0.010
0.016
1.04
8°
0.10
1°
Inches
Typ.
0.193
0.236
0.154
0.050
0.040
Max
0.069
0.010
0.019
0.010
0.197
0.244
0.157
0.020
0.050
8°
0.004
DocID2300 Rev 11
TL082, TL082A, TL082B
8.2 TSSOP8 package information
Figure 24: TSSOP8 package outline
Package information
Ref. e k
L
L1 aaa
A
A1
A2 b c
D
E
E1
Min.
0°
0.45
0.05
0.80
0.19
0.09
2.90
6.20
4.30
Table 5: TSSOP8 mechanical data
Dimensions
Millimeters
Typ. Max. Min.
1.00
3.00
6.40
4.40
0.65
1.2
0.15
1.05
0.30
0.20
3.10
6.60
4.50
0.002
0.031
0.007
0.004
0.114
0.244
0.169
0.60
1
0.1
8°
0.75
0°
0.018
Inches
Typ.
0.039
0.118
0.252
0.173
0.0256
0.024
0.039
0.004
Max.
0.047
0.006
0.041
0.012
0.008
0.122
0.260
0.177
8°
0.030
DocID2300 Rev 11 15/18
Ordering information
9 Ordering information
Order code Temperature range
Table 6: Order codes
Package
TL082ID
TL082IDT
TL082IPT
TL082CD
TL082CDT
TL082CPT
TL082ACDT
TL082BCDT
TL082IYDT (1)
TL082AIYDT (1)
TL082BIYDT (1)
-40 °C to 105 °C
0 °C to 70 °C
-40 °C to 105 °C
SΟ8
TSSOP8
SΟ8
TSSOP8
SΟ8
SO8 (automotive grade)
TL082, TL082A, TL082B
Packing
Tube or tape and reel
Tape and reel
Tube or tape and reel
Tape and reel
Tube or tape and reel
Marking
082I
082C
082AC
082BC
082IY
82AIY
82BIY
Notes:
(1)
Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening according to
AEC Q001 and Q 002 or equivalent.
16/18 DocID2300 Rev 11
TL082, TL082A, TL082B
10
Revision history
Revision history
Date Revision
Table 7: Document revision history
Changes
02-Apr-2001
2002-2003
30-Apr-2004
06-Mar-2007
12-Jun-2008
10-Jun-2016
1
2-7
8
9
10
11
Initial release.
Internal revisions.
Format update.
Added ESD information in Table 1 on page 4.
Expanded order codes table and added automotive grade order codes. See Table 7 on page 16.
Added Table 2: Operating conditions on page 4.
Updated package information to make it compliant with the latest
JEDEC standards.
Removed information concerning military temperature range
(TL082M*, TL082AM*, TL082BM*).
Removed DIP8 package and all obsolete order codes
Updated document layout
Table 4 : added L1 dimension
Figure 24 : removed silhouette and added package outline
DocID2300 Rev 11 17/18
TL082, TL082A, TL082B
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2016 STMicroelectronics
– All rights reserved
18/18 DocID2300 Rev 11
