advertisement
VIDEO MONITOR VM 7T BM
USER MANUAL
CONTENTS
1. Parts and Functions - - - - - - - - - - - - - - - - - - - - - - 1
2. Monitor Mounting - - - - - - - - - - - - - - - - - - - - - - - - 1
3. Operation Instructions - - - - - - - - - - - - - - - - - - - - - 2
3.1 Answering a Door Call - - - - - - - - - - - - - - - - - - 2
3.2 Door Release - - - - - - - - - - - - - - - - - - - - - - - - 2
3.3 Entrance Monitoring - - - - - - - - - - - - - - - - - - - 2
3.4 Intercom Function - - - - - - - - - - - - - - - - - - - - - 2
4. Basic Setup Instructions - - - - - - - - - - - - - - - - - - - 3
4.1 Ring Tone Setting - - - - - - - - - - - - - - - - - - - - - 3
4.2 Ring Volume Setting - - - - - - - - - - - - - - - - - - - - 4
4.3 Monitor Time Setting - - - - - - - - - - - - - - - - - - - 5
4.4 Unlock Parameter Setting - - - - - - - - - - - - - - - - 5
4.5 Screen Setting - - - - - - - - - - - - - - - - - - - - - - - - 6
4.6 Restore to Default - - - - - - - - - - - - - - - - - - - - - 6
5. Built -in Memory and SD Card - - - - - - - - - - - - - - - 7
5.1 Picture Recording - - - - - - - - - - - - - - - - - - - - - 8
5.2 Record times Setting - - - - - - - - - - - - - - - - - - - 8
5.3 Picture Playback - - - - - - - - - - - - - - - - - - - - - - 8
5.4 Photo Frame - - - - - - - - - - - - - - - - - - - - - - - - 9
5.4.1 Playing - - - - - - - - - - - - - - - - - - - - - - - - - - 9
5.4.2 Playing time setting - - - - - - - - - - - - - - - - - 9
6.Specification - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9
1. Parts and Functions
Manual
Monitor
Monitor Intercom
Multimedia
Memory
Playback
Album User Setup Close
09/30/2010 Thu.16:41
DIPS
ON
1 2 3 4 5 6
L1
L2
Home Screen
UNLOCK Button
MONITOR Button
TALK Button
CALL Button
MENU Button
Microphone
Ventilation Vent
Speaker
Connection Port
Mounting Hook
2. Monitor Mounting
● Use the screws to fix the Mounting Bracket on the wall.(accessories include a Bracket, two 4X25 screws (use to fasten the Mounting Bracket), 2 wire cables (use to connect with Monitor)).
● Connect the system correctly. then hang the Monitor on the Mounting Bracket firmly.
-1-
3. Operation Instructions
3.1 Answering a Door Call
● Press the CALL button on door station.
● The monitor rings,and the visitor's image will be seen on screen.
Note:the screen turns off after 30 seconds if nobody answers.
● Press TALK Button or touch icon, you can talk with the visitor for 90 seconds. During talking state, press the TALK Button again or press icon to end the conversation. If the system connects two or more Monitors, pick up any Monitor , the others will be automatically shut off.
1:1
Unlock
Talk
Capture
Home
3.2 Door Release
● During the conversation, press UNLOCK Button or touch icon to unlock the door.
(if two locks are connected to door camera,touch
unlock 2nd
icon to release the second lock )
3.3 Entrance Monitoring
● Press MONITOR button on monitor in standby mode,or touch
Monitor
icon on home screen.the screen will display the view of the
Outdoor Station. During monitoring, touch
Manual Monitor
icon to get into the camera switching mode, (or directly touch
Manual
Monitor
icon on home screen), if multi Door
Stations are installed, you can press the camera
1/2/3/4 to monitor the Door Station or CCTV camera you want.press
Home
icon to exit and enter home screen page.
1 2 3 4
Camera 1 Camera 2
Camera 3
Camera 4
Monitor
Time
Home 09/30/2010 Thu.16:41
3.4 Intercom Function
*
Intercom Call by namelist
:User in one apartment can call other apartments in the system. Press CALL button on monitor in standby mode or touch
Intercom
item on home screen page , then touch
Intercom by Namelist
icon (the namelist will be created automatically by the system). Select a name on the screen then touch
Dial
Number
icon to call.Press icon to enter last/next name list page.
-2-
* Note:1. Press "CALL" button or touch
Dial Number
icon again to redial. 2. Touch
icon to cancel the call.
Intercom by Namelist
Home
Inner Call Direct Call
Guard Unit
09/30/2010 Thu.16:41
-Name List-
[0001] Jim
[0002] Calo,Liu
[0003] Jacko,Zhang
[0004] Jana,Qiao
[0005] Hebe,Zhang
[0006] Tony,Li
Last Next
Dial
Number
Close
*
Inner Call
: If multi Monitors are installed in one user, select and press the Inner Call item, the other Monitors will ring at the same time, whichever Monitor answers the call, conversation is started,and the other monitors will stop ringing at the same time.
*
Direct Dial Guard unit
: A Monitor can be assigned as Guard Unit Monitor; when the
Guard Unit Monitor answers the call, conversation with the guard person is started..
4. Basic Setup Instructions
4.1 Ring Tone Setting
12 pieces ring tones can be selected.
● Touch the screen anywhere (or press MENU button ) in standby mode,a full screen calendar will be showed.
09/30/2010 Thu.
16:41
1. Current date
2. Current day
3. Current time.
-3-
● Touch the screen again (or press MENU button again) to enter home screen. then touch
User Setup
icon to enter call tone setting screen,touch Door station call tone/intercom call tone/door bell call tone,12 pieces ring tones will be displayed , Choose a ring tone which you want, then touch icon to save and exit, the ring tone will be performed. or touch icon to unsave and exit.
Door Station
Call Tone
Exit&Save
Carman
Ding Dong
Rhythm of the rain
For Elise
Sonatine
Edelweiss
Exit&Unsave
Going Home
Congratulate
Do Re Me
Happy Birthday
Jingle Bell
Telephone Ring
4.2 Ring Volume Setting
Ring Volume
You can set a ring volume for day time,6:00
AM~18:00 PM is the day time by default,enter home screen page(refer to 4.1) then touch
User Setup
icon to enter next page,and then touch
Ring Volume
icon to enter Ring
Volume page,Use icon to decrease/ increase the volume. then touch icon to save and exit,or touch icon to unsave and exit.
Ring Volume
Exit&Save
Adjust -
6
7
Exit&Unsave
Adjust +
Night Ring Volume
You can active a ring volume for night time,18:00 PM~6:00 AM is the night time by default,if you don't want to be disturbed at night ,you can set the volume to 0.Enter home screen page(refer to 4.1) touch
User Setup
icon to enter next page, then touch
Night Ring Volume
icon to enter Night Ring Volume page,Use icon to decrease/increase the volume.After setting a value you want,you should touch
Ring Volume
icon to active the setting, after that the Ring Volume icon will change to Night Ring Volume icon. then touch icon to save and exit,night ring volume will be performed. or touch icon to unsave and exit.
Note:touch
Night Ring Volume
icon again,you can cancel the night ring volume setting.
-4-
Night Ring
Volume
Exit&Save
Adjust -
Ring
Volume
4
Adjust +
Exit&Unsave
Night Ring
Volume
Exit&Save
Adjust -
Night Ring
Volume
7
4
Adjust +
Exit&Unsave
4.3 Monitor Time Setting
● Enter home screen page(refer to 4.1),thenTouch
Manual Monitor
icon to enter next page.and then press
Monitor Time
icon to enter monitor time setting page.
● Input digitals by pressing the digital keypad, and press icon to change the setting location,and press icon to save. Settings will be performed immediately, press icon to return last page .
1 2 3 4
Camera 1 Camera 2
Camera 3
Camera 4
Monitor
Time
Home 09/30/2010 Thu.16:41
1
4
Monitor time set min:[01] sec:[30]
7
2
5
8
0
9
3
6
Cancel
4.4 Unlock Parameter Setting
● Enter home screen page(refer to 4.1),thenTouch easydor™ icon to enter next page.
and then touch the screen anywhere and hold for 2s to enter next menu.
H/W DT14-CT a1.3
S/W: V11.01008.00
Voltage: ---
Local addr: 01.00
Unlock timing: 5s
Video standard: NTSC
Cancel
Installer setup
Device
Property
Caliber
TouchScreen
Home
-5-
● Touch
Installer setup
icon,a digital keypad and installation setting will be showed on screen.
● Input code number by touching the digital keypad.According to the left instructions,
8010 and 8011 are used to set the unlock mode(0 and 1). 8021~8029 are used to set the unlock time (1s~9s) .use to cancel the input,and use to save the setting.
Touch icon to return last page .
4.5 Screen Setting
When the Monitor is in monitoring or talking state, Press
Adjust
icon to enter screen setting page.Touch any item you want,then touch to decrease or increase the value.Settings will be performed immediately. Press icon to exit out the page.
4.6 Restore to Default
The restore to default function allows the user to recover the settings to factory setting.
Note that the restore to default operation will not change the time setting and the datas on buit-in memory or SD card.
Enter home screen page(refer to 4.1),then touch
User Setup
icon to enter the setting page,press Restore to default item, the default settings will be loaded. press
Home
icon to return to home screen page.
Installation settings:
[0010]#:Remove all remote control
[0011]#:Add remote control
[8000]#:Set as master unit 0
[8001]#:Set as slaver unit 1
[8003]#:Set as slaver unit 3
[8004]#:Set as guard unit
[8005]#:Set as not guard unit
[8010]#:Set lock mode to 0
[8011]#:Set lock mode to 1
[8022]#:Set the lock time of 2s
[8023]#:Set the lock time of 3s
[8025]#:Set the lock time of 5s
[8026]#:Set the lock time of 6s
[8028]#:Set the lock time of 8s
[8029]#:Set the lock time of 9s
Code Number:[----]
1 2 3
4 5 6
7 8
0
9
Cancel
Adjust -
5
Adjust +
Brightness color scene
Talk Volume
Adjust Return
Door Station
Call tone
Intercom
Call tone
DoorBell
Call tone
Clock
Ring
Volume
Home
Night Ring
Volume
Refault to
Default
09/30/2010 Thu.16:41
-6-
5. Built -in Memory and SD Card
This Monitor has been equipped with a built-in memory (about 120 MB) together with a SD card reader. Maximum 16 GB SD card can be supported.
SD card
● The monitor can play photos and pictures.
● Photo frame function, each photo playing will last 5 seconds, More pictures in the SD card, longer time for triggering the function, 800 pictures is supported in inner memory. With 2G SD card,more than 30000 pictures can be supported.
● Must use T-views album software tool to transform the JPG format photos took by digital camera to TVS format photos that can be viewed on Monitor.
● The captured pictures will be saved in a folder named by date,note that the pictures recording every day will be saved in different folders which automatically generated every day.
● The captured pictures in the built-in memory can be copied to the SD card, and you should use T-views memo software tool to convert the pictures to JPG format that can be seen on the computer. (select the pictures(press Ctrl+A to select all)->>click the right key of the mouse
->>choose transfer selected to JPG item->>save the pictures on computer)
● When the built-in memory is full,the oldest picture will be deleted to make room for new record .
● The built-in memory can be formatted by the Monitor,but SD card cannot,you should format the
SD card on computer.
● Avoid to plug in/out the SD card when the monitor is under operation.
● Playing will be interrupted by the calling from outdoor station.
-7-
5.1 Picture Recording
Both Auto-Recording and Manual-Recording are available.and Auto-Recording is default. If receive a Call , after 3s, the monitor will record automatically. or you can touch
Capture
icon to record the visitor's image manually.
5.2 Record times Setting
You can setup Memo Options to choose 1/4/8 pictures memo. If 4/8 was chosen, you will have
4/8 shots for each recording operation, and every 1.5 seconds catch a picture.
Touch
Multi Media
icon on home screen to enter next page, then touch
Memory
Options
icon,a digital keypad will be showed on the screen,you can only set the record times for 1/4/8 by touching the digital keypad.touching other digitals are unvalid .and press icon to save. Settings will be performed immediately, press icon to return last page .
5.3 Picture Playback
Touch
Memory Playback
icon on home screen,4 pictures will be displayed in the memo for each page. you can touch or to enter last or next picture memo,or touch icon to delete all pictures. And you can zoom the picture on full screen by touch icon , on full screen mode, touch icon to preview last/next picture.or you can touch icon to delete the picture you are previewing.press
icon to return home screen page.
-8-
DS1 00:03 Talking
Recording...
1:1
Unlock
Talk
Capture
Home
Record times: [ 1 ]
1
4
7
2
5
8
0
3
6
9
Cancel
Picture 4 Picture 3
2010-9-30 004 2010-9-30 003
Picture 2 Picture 1
2010-9-30 002 2010-9-30 001
Full Screen
Page UP
Page Down
Delete All
Home
5.4 Photo Frame
5.4.1 Playing
Touch
Album
icon on home screen to play the photos(must plug in SD card).it can be played both manually and automatically,use your fingers to slide right or left on screen to play last/next photo.
5.4.2 Playing time setting
Touch
Multi Media
icon on home screen to enter next page, then touch
Album
Options
icon,a digital keypad will be showed on the screen,then you can set the playing time by touching the digital keypad to input digitals and press icon to change the location,and press
icon to save. Settings will be performed immediately, press icon to return last page .
1
4
Album time set min:[01] sec:[30]
7
2
5
8
0
9
3
6
Cancel
6.Specification
Power Supply :
Power Consumption:
Monitor Screen:
Display Resolution:
Built-in Memory:
Picture Memo:
Monitor Dimension: supplied by
power separator
Standby 15mA; Working status 400mA
7 Inch color TFT-LCD
800*3(RGB)*480 pixels
120 MB
800pcs(inner memory),>30000pcs(2G SD card)
138(H)×235(W)×24(D)mm
-9-
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 1. Parts and Functions
- 3 2. Monitor Mounting
- 4 3. Operation Instructions
- 4 3.1 Answering a Door Call
- 4 3.2 Door Release
- 4 3.3 Entrance Monitoring
- 4 3.4 Intercom Function
- 5 4. Basic Setup Instructions
- 5 4.1 Ring Tone Setting
- 6 4.2 Ring Volume Setting
- 7 4.3 Monitor Time Setting
- 7 4.4 Unlock Parameter Setting
- 8 4.5 Screen Setting
- 8 4.6 Restore to Default
- 9 5. Built -in Memory and SD Card
- 10 5.1 Picture Recording
- 10 5.2 Record times Setting
- 10 5.3 Picture Playback
- 11 5.4 Photo Frame
- 11 5.4.1 Playing
- 11 5.4.2 Playing time setting
- 11 6.Specification