Zimmer A.L.P.S Elbow Fracture System Owner's Manual

A.L.P.S.

™ Elbow Fracture

Plating System

Surgical Technique

1 | A.L.P.S. Elbow Fracture Plating System

Table of Contents

Surgeon Design Team ................................................................................................. 2

Low Profile Anatomically Contoured Elbow Plates ....................................................... 3

F.A.S.T. Guide Insert Technology, F.A.S.T. Tabs Technology, Provisional Fixation .......... 5

Locking, Non-Locking and Multi-Directional Locking Screw Options ........................... 6

Introduction ............................................................................................................... 8

Medial Plate ................................................................................................................ 9

Lateral Plate .............................................................................................................. 10

Posterior Lateral Plate ............................................................................................... 11

Olecranon Plate ........................................................................................................ 12

Coronoid and Proximal Radial Plates ......................................................................... 13

A.L.P.S. Elbow Long Plates ........................................................................................ 14

A.L.P.S. Elbow Plate Trials .......................................................................................... 15

Screw Specification .................................................................................................. 16

Anatomy ................................................................................................................... 18

Patient Position ........................................................................................................ 20

Exposing the Distal Humerus through an Olecranon Osteotomy ............................... 21

Distal Humerus Fracture Reduction .......................................................................... 23

Humeral Fracture Plate Selection and Screw Placement ............................................ 24

Humeral Fracture Plate Fixation ................................................................................ 25

Exposing the Radial Head ......................................................................................... 30

Radial Head Fracture Fixation ................................................................................... 32

Exposure of the Coronoid ......................................................................................... 34

Coronoid Fracture Fixation ....................................................................................... 35

Exposure of the Olecranon ....................................................................................... 38

Olecranon Fracture Fixation ..................................................................................... 39

Appendix A Plate Contouring .................................................................................... 41

Appendix B Screw Insertion ...................................................................................... 46

Appendix C Screw Removal ...................................................................................... 50

Instrument Trays....................................................................................................... 51

2 | A.L.P.S. Elbow Fracture Plating System

3 | A.L.P.S. Elbow Fracture Plating System

Low Profile Anatomically

Contoured Elbow Plates

• Low profile plate is designed to help minimize discomfort and soft tissue irritation.

• Engineered from TiMAX ® for strength, biocompatibility and a smooth implant surface.

• Contoured plates mimic the anatomy of the distal humerus, olecranon, radial head and coronoid.

• Available in small and large sizes to best match anatomy.

• Bullet tip is designed to minimize soft tissue disruption during insertion.

• Low profile F.A.S.T. Guide ® inserts for percutaneous application.

• Adapters available for fixed angle K-wire placement for provisional fixation.

The A.L.P.S. Elbow Plating System features an extensive set of anatomically contoured implants to address a wide array of fractures around the elbow.

The anatomic design of each plate is designed to match the natural anatomy of the specified location.

However, in-situ contouring is available for fine adjustment for patient modification.

4 | A.L.P.S. Elbow Fracture Plating System

5 | A.L.P.S. Elbow Fracture Plating System

F.A.S.T. Guide Insert Technology

• Pre-loaded and disposable F.A.S.T. Guide inserts facilitate accurate drilling and reduce intraoperative assembly, saving time in the OR.

F.A.S.T. Tabs

®

Technology

• Enables in-situ contouring for true plate-to-bone conformity.

Provisional Fixation

• K-wire placement through provisional fixation holes for immediate and secure plate positioning.

The A.L.P.S. Elbow Plating System comes pre-loaded with Fixed Angle Screw Targeting

Guides – F.A.S.T. Guide inserts – that direct the trajectory of the drill through the screw hole in the plate. Additionally, F.A.S.T. Tabs technology allows for in-situ contouring for anatomy specific modification, while provisional fixation holes allow the plate to be securely positioned with K-wires.

6 | A.L.P.S. Elbow Fracture Plating System

Locking, Non-Locking and

Multi-Directional Locking

Screw Options

• Choose locking, non-locking, or multi-directional locking screws according to need.

• Tapered, threaded screws lock into position when tightened to establish a fixed angle construct for strong fixation or when bone quality is poor and optimal screw purchase is required.

• Multi-directional locking screws (MDS) allow for up to a 25 degree cone of angulation and lock into the plate by creating their own thread.

• Low profile non-locking screws provide the same profile as locking screws.

• Slotted holes allow for axial compression.

Particularly helpful in challenging fracture cases, the interlocking screw construct of the Elbow

Plates provides both versatility and strength.

The addition of the MDS screw technology allows the target and capture of fragments for optimum fixation. With the added feature of the low profile non-locking screw, whichever screw option is chosen allows the plate profile to be maintained for minimal soft tissue disruption.

7 | A.L.P.S. Elbow Fracture Plating System

8 | A.L.P.S. Elbow Fracture Plating System

Introduction

The A.L.P.S. Elbow Plating System is a comprehensive system designed to address fractures around the elbow.

The system includes anatomically contoured plates including Medial, Lateral, Posterior Lateral, Olecranon,

Proximal Radial Head, and Coronoid designs. All plates have TiMAX surface treatment benefits of increased fatigue strength compared to 316L Electropolished

Stainless Steel, Type I Anodized titanium, and machined titanium.

1 F.A.S.T. Guide inserts incorporating flexible plating technology have been inserted into all implants for fast drilling as well as in-situ contouring to allow for a true anatomic fit.

Note: The pre-assembled F.A.S.T. Guide inserts are

NOT to be removed prior to sterilization. They should be removed and discarded only after use.

9 | A.L.P.S. Elbow Fracture Plating System

Medial Plate

Proximal bullet tip facilitates submuscular plate insertion

2.0 mm K-wire Adapter converts any F.A.S.T. Guide insert into a fixed angle K-wire hole

Low profile, anatomically contoured plate designed to minimize soft tissue irritation

Slotted holes for active compression

Provisional 1.6 mm K-wire fixation slot

Design features allow for multiplanar plate contouring

3.5 mm multi-directional locking screws allow for 25 degrees of angulation

Medial Plate Specifications

Length

Width

Thickness

88 mm

10.9 mm

2.5 mm

97 mm

10.9 mm

2.5 mm

127 mm

10.9 mm

2.5 mm

166 mm

10.9 mm

2.5 mm

Elbow Trials: The 3.5 mm Elbow trials will use the 2.7 mm locking drill guide 2142-07-027 as the trial holder.

10 | A.L.P.S. Elbow Fracture Plating System

Lateral Plate

Proximal bullet tip facilitates submuscular plate insertion

2.0 mm K-wire Adapter converts any F.A.S.T. Guide insert into a fixed angle K-wire hole

Low profile, anatomically contoured plate designed to minimize soft tissue irritation

Slotted holes for active compression

Fixed angle K-wire slot for provisional plate fixation with a 1.6 mm K-wire

Design features allow for contouring in the coronal plane

Reference tabs on the lateral edge of the plate are designed to maintain stability on the posterior ridge of the distal humerus.

Design features allow for multiplanar plate contouring

3.5 mm multi-directional locking screws allow for 25 degrees of angulation

Lateral Plate Specifications

Length 64 mm

Width 9.7 mm

Thickness 2.4 mm

85 mm

10.7 mm

2.4 mm

103 mm

10.7 mm

2.5 mm

142 mm

10.7 mm

2.5 mm

Elbow Trials: The 3.5 mm Elbow trials will use the 2.7 mm locking drill guide 2142-07-027 as the trial holder.

11 | A.L.P.S. Elbow Fracture Plating System

Posterior Lateral Plate

Low profile F.A.S.T. Guide inserts designed to minimize soft tissue irritation during plate insertion

2.0 mm K-wire Adapter converts any

F.A.S.T. Guide insert into a fixed angle K-wire hole

Plate undersurface contour allows for bending in the coronal plane

Slotted holes for active compression

Multiplanar arms designed to allow for eccentric screw positioning

Isolated lateral screw for trochlear fixation

Plate cut-outs engineered to allow for plate contouring in the coronal plane

Extremely distal condylar screw position

Posterior Lateral Plate Specifications

Length 74 mm 94 mm

Width 10.7 mm 10.7 mm

Thickness 3.5 mm 3.5 mm

148 mm

10.7 mm

3.5 mm

Elbow Trials: The 3.5 mm Elbow trials will use the 2.7 mm locking drill guide 2142-07-027 as the trial holder.

12 | A.L.P.S. Elbow Fracture Plating System

Olecranon Plate

Low profile F.A.S.T. Guide inserts designed to minimize soft tissue irritation during plate insertion

Low profile F.A.S.T.

Guide inserts for percutaneous fixation

2.0 mm K-wire Adapter converts any

F.A.S.T. Guide insert into a fixed angle K-wire hole

Slotted holes for active compression

Low profile screw heads for either locking or non-locking options

Anatomically positioned coronoid screw

Multiplanar arm for optimal placement

Small olecranon plate offers one tab option Small olecranon plate

Isolated olecranon screw

Bridging screw designed for maximum subchondral support

Two tab option for larger olecranon

Olecranon Plate Specifications

Overall Length 79 mm

Shaft Width 10.7 mm

Thickness 2.5 mm

104 mm

10.7 mm

2.5 mm

154 mm

10.7 mm

2.5 mm

194 mm

10.7 mm

2.5 mm

Elbow Trials: The 3.5 mm Elbow trials will use the 2.7 mm locking drill guide 2142-07-027 as the trial holder.

13 | A.L.P.S. Elbow Fracture Plating System

Coronoid and Proximal Radial Plates

Coronoid Plate Specifications

Length 37.2 mm

Width

Thickness

28 mm

1.5 mm

Threaded holes for 2.5 mm locking and non-locking screws

Paddle for buttressing the sublime tubercle

Multiplanar trajectories

Paddle for buttressing the coronoid process

Suture point for fixation of capsule

Proximal Radial

Plate Specifications

Length

Width

Thickness

Small

29 mm

17.5 mm

1.5 mm

Large

36.5 mm

18 mm

1.5 mm

Dual radial curvatures designed for maximum fit

Elbow Trials: The 2.5 mm Elbow trials (Proximal Radius and Coronoid) will use the existing plate holder 2312-07-012.

14 | A.L.P.S. Elbow Fracture Plating System

A.L.P.S. Elbow Long Plates

A.L.P.S. Elbow Plates Module (2312-18-110) F.A.S.T. Guide Inserts

A.L.P.S. Elbow System Tray (2312-18-100) Long Plate Benders

Product Information

The longer A.L.P.S. Elbow Plates are housed in a separate tray module (2312-18-110). The long implant module replaces the 2.5 mm Caddy (2312-18-106) in the A.L.P.S. Elbow System Tray (2312-18-100).

F.A.S.T. Guide Inserts

Extended shaft sections of long plates do not have pre-assembled F.A.S.T. Guides. User can assemble

F.A.S.T. Guide (2312-18-016) onto threaded holes at their discretion for use as drill guides. F.A.S.T. Guide will be provided on a wireform dispenser. Also, a threaded drill guide (2142-07-027) is provided in the tray as an alternate. The F.A.S.T. Guide inserts are

NOT to be used to bend the shaft of the longer plates. Refer to contouring section in Appendix A below.

Contouring for Long Implants

The long plate benders (2312-18-001) are used to contour the shaft portion of the long implants.

Benders consist of 3 bending features: the foot, the slot, and the planar bending feature (teeth).

15 | A.L.P.S. Elbow Fracture Plating System

A.L.P.S. Elbow Trials

The A.L.P.S. Elbow Trials are designed to aid in the selection of the correct size implant. The trials are manufactured from color anodized titanium alloy (Left

= Lime; Right = Rose; Bilateral = Blue). The A.L.P.S.

Elbow trials match the shape of the implant but are not designed to be bent. The trials can be used for selecting the elbow implants found below.

Trials are provided for the shorter length of a particular plate family. For example, the Distal Humeral Lateral

Right Trial (2312-18-200) can be used for either the

7 hole plate or 9 hole plate.

Sterile Plate

Catalog No.

Non-Sterile Plate

Catalog No.

Trial

Catalog No.

Lateral Plates

8513-18-200

8513-18-201

8513-18-202

8513-18-203

1312-18-200

1312-18-201

1312-18-202

1312-18-203

2312-18-200

N/A

2312-18-202

N/A

To position the trials:

• For the Lateral, Posterior Lateral, and Medial

Distal Humerus and Olecranon trials, use the

2.7 mm locking drill guide (2142-07-027)

• For the Coronoid and Proximal Radius trials, use the Plate holder (2312-07-012).

Note: The A.L.P.S. Elbow trials cannot be implanted.

Trial

Descriptions

Distal Humerus Lateral Right 7 Hole Trial

N/A

Distal Humerus Lateral Left 7 Hole Trial

N/A

Posterior Lateral Plates

8513-18-300

8513-18-301

8513-18-302

8513-18-303

1312-18-300

1312-18-301

1312-18-302

1312-18-303

2312-18-300

N/A

2312-18-302

N/A

Distal Humerus Posterior Lateral Right 9 Hole Trial

N/A

Distal Humerus Posterior Lateral Left 9 Hole Trial

N/A

Proximal Radius Plates

8513-18-400

8513-18-401

1312-18-400

1312-18-401

2312-18-400

N/A

Proximal Radius Plate Trial

N/A

Coronoid Plates

8513-18-500

8513-18-501

1312-18-500

1312-18-501

2312-18-500

2312-18-501

Coronoid Plate Right Trial

Coronoid Plate Left Trial

Olecranon Plates

8513-18-600

8513-18-601

1312-18-600

1312-18-601

2312-18-600

N/A

Olecranon Plate 10 Hole Trial

N/A

Medial Plates

8513-18-700

8513-18-701

8513-18-702

8513-18-703

1312-18-700

1312-18-701

1312-18-702

1312-18-703

2312-18-700

N/A

2312-18-702

N/A

Distal Humerus Medial Right 9 Hole Trial

N/A

Distal Humerus Medial Left 9 Hole Trial

N/A

16 | A.L.P.S. Elbow Fracture Plating System

Screw Specification

2.5 mm Locking Screw:

• Self tapping tip minimizes the need for pre-tapping and eases screw insertion

• 1.3 mm Square driver to maximize torque delivery

• Triple lead thread on screw head is designed to reduce possible cross threading

• Tapered threads are designed to reduce potential of screw backout

• Available in lengths of 14 – 40 mm

• Screw uses a Drill Bit F.A.S.T. 2.0 mm (FDB20)

2.5 mm Non-Locking Screw:

• Self tapping tip minimizes the need for pre-tapping and eases screw insertion

• 1.3 mm Square drive to maximize torque delivery

• Available in lengths of 14 – 40 mm

• Screw uses a Drill Bit F.A.S.T. 2.0 mm (FDB20)

3.5 mm Locking Cortical Screw:

• Large core diameter and shallow thread pitch for bending and shear strength

• Self tapping tip minimizes the need for pre-tapping and eases screw insertion

• Tapered screw head helps ensure alignment of the screw head into the plate hole

• Tapered threaded head is designed to minimize screw back-out and construct pullout

• T-15 drive

• Available in lengths of 10 – 70 mm

• Screw uses a 2.7 mm Drill Bit (2142-27-070)

17 | A.L.P.S. Elbow Fracture Plating System

3.5 mm Low Profile Non-Locking Screw:

• Low profile head design reduces prominence beyond the plate

• Self tapping tip minimizes the need for pre-tapping and eases screw insertion

• 2.2 mm Square drive to maximize torque delivery

• Available low profile washer converts screw head to traditional non-locking screw head size for use in active compression holes

• Screw uses a 2.5 mm Drill Bit (8290-29-070) and can be inserted in any of the threaded holes in the plate

• Available in lengths of 14 – 75 mm

Active Compression Conversion Washer:

• Cobalt chrome washer designed to snap onto the head of low profile

3.5 mm non-locking screw

• Washer converts low profile screw head into a standard profile non locking screw

• Allows for active compression in the oblong slots

Note: The washer is for use

ONLY with the 3.5 mm Low

Profile Non-Locking Screw

3.5 mm Locking Multi-Directional Screw:

• Cobalt chrome screw with large core diameter

• Multi-Directional capability offers a 25 degree cone of angulation

• Creates own thread in plate to help provide strong and stable construct

• Self tapping tip minimizes the need for pre-tapping and eases screw insertion

• 2.2 mm square drive

• Available in lengths of 20 – 60 mm

• Screw uses a 2.7 mm Drill Bit (2142-27-070)

18 | A.L.P.S. Elbow Fracture Plating System

Anatomy –

Soft Tissue of the Elbow

Biceps

Brachii m.

Bicipital

Aponeurosis

Common

Flexor Tendon

Pronator

Teres m.

Flexor Carpi

Ulnaris m.

Anterior view in extension

Triceps Brachii

Tendon

Brachioradialis m.

Brachialis m.

Extensor Carpi

Radialis Longus

Common

Extensor Tendon

Anconeus m.

Brachioradialis m.

Extensor Carpi

Radialis Longus m.

Extensor Carpi

Ulnaris m.

Extensor Carpi

Radialis Brevis m.

Extensor Digitorum m.

Extensor Carpi

Radialis Brevis m.

Flexor Digitorum

Superficialis m.

Posterior view in extension

Ulna Nerve

Flexor Carpi

Ulnaris m.

19 | A.L.P.S. Elbow Fracture Plating System

Anatomy –

Bones of the Elbow

Anterior view in extension

Medial

Supracondylar Ridge

Coronoid

Fossa

Trochlea

Medial

Epicondyle

Coronoid

Process

Radial Notch of Ulna

Tuberosity

Ulna

Humerus Humerus

Lateral

Supracondylar Ridge

Radial Fossa

Olecranon

Fossa

Lateral

Epicondyle

Lateral

Epicondyle

Capitulum

Head

Neck

Head

Neck

Tuberosity

Tuberosity

Radius Radius

Posterior view in extension

Medial

Epicondyle

Groove for

Ulnar Nerve

Olecranon

Ulna

20 | A.L.P.S. Elbow Fracture Plating System

Figure 1

The supine position with the arm across the chest.

Figure 2

The prone position with the forearm extended laterally to the side of the operating table.

Patient Positioning

For treatment of distal humerus and/or olecranon fractures, the patient may be placed in either the supine, lateral or prone positions, depending on surgeon preference.

In the supine position, the arm is placed across the chest. The surgeon stands on the side of the patient closest to the fracture with the patient brought to the very edge of the table. Inclining the table 20 to 30 degrees away from the operating surgeon will help keep the arm positioned across the chest (Figure 1).

After sterile preparation and drape, the arm is placed across a small bolster which can help maintain the position and flexion of the proximal forearm. For optimum exposure, the arm should accommodate over 100 degrees of flexion. The surgeon stands facing the elbow and is ready to begin the procedure.

The prone position can also be used. An arm board is placed parallel to the table to extend the table laterally, and a bolster is placed on the arm board to adjust for height. The elbow and forearm are positioned over the bolster. The forearm may be wrapped to prevent swelling of the dependent hand.

This position requires more involvement of the anesthesia team, but for surgeons that are comfortable with this position it can provide good operative exposure and gravitational aid in reduction of the fracture fragments (Figure 2).

21 | A.L.P.S. Elbow Fracture Plating System

Hand

Ulnar Nerve

Shoulder

Step 1

Initial incision.

Step 2

Prepare for olecranon plate fixation prior to creating osteotomy.

Exposing the Distal Humerus through an Olecranon Osteotomy

Step 1

The incision starts approximately 10 cm proximal to the tip of the olecranon and approximately 10 cm distal to the tip of the olecranon. Full thickness skin flaps are elevated (Step 1). Incise the medial and lateral joint capsule to visually identify and mark the central aspect of the greater sigmoid notch. This area is typically devoid of cartilage.

The ulnar nerve should be identified in the cubital tunnel, isolated and mobilized to protect it before the osteotomy is performed.

An osteotomy of the olecranon is performed to expose the distal humerus. This can be a chevron type or straight transverse osteotomy. In this technique, a chevron osteotomy is used to gain exposure to the distal humerus. The point of the chevron osteotomy should face the wrist to maximize bone on the olecranon fragment.

Step 2

The olecranon plate multiplanar side arms should be removed if the plate will be used specifically for olecranon osteotomy fixation. When removing the arms, they should be broken off by bending toward the underside of the plate so that any rough edges are left underneath the plate.

The plate is positioned on the intact olecranon. A

K-wire is drilled (using a K-wire Adapter placed in the

F.A.S.T. Guide inserts) through the home run screw hole of the plate. A distal K-wire through the plate can also be used to secure the plate to the bone. Then drill and insert the twin proximal olecranon 3.5 mm locking screws. These screws and the K-wire are then removed and the plate is removed. These screw and

K-wire holes will serve as reference points for anatomic reduction and fixation of the olecranon osteotomy later in the procedure.

22 | A.L.P.S. Elbow Fracture Plating System

Step 3

The posterior two-thirds of the olecranon is cut with a saw.

The osteotome is then used as a lever to break off the articular surface of the olecranon.

Exposing the Distal Humerus through an Olecranon Osteotomy

(cont.)

Step 3

A standard chevron or transverse osteotomy is then performed. This should be done under full visualization of the olecranon articular surface to be sure the trajectory of the osteotomy enters the bare area. If the osteotomy is performed too distal, reduction may be more difficult. If the osteotomy is performed too proximal, exposure of the distal humerus may be poor.

The osteotomy is performed using a narrow sawblade.

The osteotomy is completed with an osteotome. Use the osteotome as a lever to allow for interdigitation of the rough edges at the end of the procedure, allowing for optimum fragment reduction and fixation.

Step 4

At the end of the procedure, the olecranon osteotomy is repaired with a plate.

Step 4

At the end of the procedure, when the olecranon osteotomy is ready to be reduced, placing the twin

3.5 mm Locking Screws in the proximal fragment first will allow the plate to be used as a handle to aid in reduction. Once satisfactory reduction is obtained, follow the steps described in the Olecranon Fracture

Fixation section (Pages 39-40) to complete fixation of the olecranon osteotomy.

23 | A.L.P.S. Elbow Fracture Plating System

Step 1

Fragment reconstruction.

Step 2

K-wire placement.

Distal Humerus

Fracture Reduction

Step 1

The first step to reduction is to identify the major fracture fragments and develop a plan for reassembly of the fracture. Typically, the best approach is to reassemble from distal to proximal reducing the articular surface first.

When placing K-wires or isolated lag screws for provisional fixation, care should be taken to place them in the area of the bone that will not interfere with plates or screws. If a segment of the distal humerus is missing or comminuted, a bone graft may be positioned to maintain the proper width of the distal humerus.

Note: The most important fragments to assemble accurately are the anterior trochlea and the capitellum. The anterior and medial aspect of the distal humerus is most important for stability whereas fracture fragments of the posterior trochlea and posterior aspect of the capitellum can be sacrificed if significant comminution has taken place (Step 1).

Step 2

Once the distal segment of the humerus containing the articular surface has been reconstructed, this fracture construct can be connected to the humeral shaft using

K-wires. Often two K-wires may be needed to cross the fracture site to gain stability and preliminary reduction of the fracture (Step 2).

24 | A.L.P.S. Elbow Fracture Plating System

Figure 1

Medial and Lateral plates.

Figure 2

Medial and Posterior Lateral plates.

Figure 3

Humeral Fracture Plate Selection and Screw Placement

Once reduction and/or ORIF of the articular surface with isolated lag screws is accomplished, and satisfactory reduction of the shaft component of the fracture is achieved, plates can then be positioned on either the medial and lateral columns or on the posterior lateral aspect of the humerus (Figures 1 and 2).

Note: When applying the Medial and Lateral plates, there is an increased chance of hitting screws with the drill bit when drilling towards the side with screws already inserted.

Multi-directional screws are available to assist in avoiding other screws that are already placed

(Figure 3).

25 | A.L.P.S. Elbow Fracture Plating System

K-wire Adapter

Step 1

The first plate is held in place with the Large Reduction Clamp.

Note: Isolated lag screws may be used to reduce the articular surface.

Step 2

Alternatively, a K-wire is inserted through the distal F.A.S.T. Guide inserts.

Humeral Fracture Plate Fixation

Determine, and place first, the plate which will gain best initial stability. The placement technique is the same for Medial, Lateral and Posterior Lateral plates.

The less involved fragment can often be reduced better anatomically than the more comminuted side.

This allows the more comminuted side to be built off of the more stable side to limit the possibility of nonanatomic angulation.

Step 1

The first plate is placed onto the condyle manually and then one of the Large Reduction Clamps (1920) and

13577) may be used to hold this in position (Step 1).

Often it is possible to place both column plates in a parallel fashion and use the large fracture Reduction

Clamp to secure both plates at once to the distal humerus.

Step 2

Alternatively, the plates may be secured to the bone by using K-wire Adapters (2312-18-007) and inserting fixed angle 2.0 mm K-wires (14179-6) through the

F.A.S.T. Guide inserts in the proximal and distal segments of the plates (Step 2).

26 | A.L.P.S. Elbow Fracture Plating System

Step 3

During placement it is possible to bend the plate slightly for optimal fit.

Step 4b

Posterior Lateral Plate

Step 4a

Apply plate to the bone and insert a K-wire through the distal 3 rd position to verify its position.

Humeral Fracture

Plate Fixation (cont.)

Step 3

During placement it is possible to contour the plate for optimal fit by using the Plate Benders (2312-18-003 and 2312-18-004). The plate can be further contoured if needed in-situ (Step 3).

Note: For further information on plate contouring refer to Appendix A on pages 41-42 and 44-45 for long plates.

Step 4a

Apply the plate to the bone and insert a K-wire through the distal 3 rd position and verify that it exits on the opposite condyle (Step 4).

Step 4b – Posterior Lateral Plate

The plate is designed to be placed in the area of the posterior lateral epicondyle. Implantation of the plate should not impinge on the articulating surface. Select the most appropriate size to fit the individual.

Once the fracture has been reduced using the surgeon's preferred method, the posterior lateral plate can be secured to the bone by using K-wire Adapters

(2312-18-007) and inserting fixed angle 2.0 mm

K-wires (14179-6) through the F.A.S.T. Guide inserts in a hole distal and proximal to the fracture. This will stabilize the plate to the bone (Step 4b).

27 | A.L.P.S. Elbow Fracture Plating System

Step 5

Use the Large Reduction Clamp to compress the plate to the bone. A 2.0 mm K-wire is inserted through a K-wire Adapter in the most proximal hole in the plate.

Step 7

Use the Large Reduction Clamp to compress the plate to the bone.

A 2.0 mm K-wire is inserted through a K-wire Adapter in the most proximal hole in the plate.

Step 6

Apply the medial plate to the bone and insert a K-wire through the distal 3 rd position to verify its position.

Humeral Fracture

Plate Fixation (cont.)

Step 5

Use the Large Reduction Clamp to compress the plate to the bone.

A 2.0 mm K-wire is inserted through a K-wire Adapter in the most proximal hole in the plate. This will stabilize the plate to the bone. Once inserted, the distal aspect of the plate can be contoured in-situ for optimal fit (Step 5).

Step 6

The medial plate is now positioned on the bone

(Step 6).

Step 7

Use the Large Reduction Clamp to compress the medial plate to the bone, and repeat Step 5 (Step 7).

28 | A.L.P.S. Elbow Fracture Plating System

Step 8a

Insert the distal screws to secure the distal fragment.

The screw insertion should alternate from one side to the other side.

Step 9a

If axial compression of the fracture is needed through the plate, the proximal K-wire is removed and a low profile Non-Locking screw with a washer is inserted in the active compression slot.

Step 8b

Posterior Lateral Plate

Humeral Fracture

Plate Fixation (cont.)

Step 8a

Insert the distal screws to secure the distal fragment.

The screw insertion should alternate from one side to the other side.

Step 8b – Posterior Lateral Plate

Insert the distal screws to secure the distal fragment.

The screw insertion should continue proximally to secure the capitulum to the plate. The distal condylar screws should be placed as long as possible, without exiting the opposite cortex. Use fluoroscopy to confirm that the screw placement is not violating the articulating surface.

Step 9a

If axial compression of the fracture is needed through the plate, the proximal K-wire is removed and a low profile Non-Locking screw with a washer is inserted in the active compression slot (Step 9a).

29 | A.L.P.S. Elbow Fracture Plating System

Step 9b

If compression at the fracture site was achieved with a clamp, the proximal screws can be filled with Locking or Non-Locking screws.

Step 10

Non-Locking, Locking or Multi-Directional screws are used to fill the remaining screw holes.

Humeral Fracture

Plate Fixation (cont.)

Step 9b - Alternative method

If compression at the fracture site was achieved with a clamp, the proximal screw holes may be filled with

Locking or Non-Locking screws (Step 9b).

It is recommended to use a Non-Locking screw in the most proximal screw holes to facilitate an optimal transition of stress from plate construct to the unplated bone.

See Appendix B on pages 46-49 for screw insertion.

The distal screws should be placed as long as possible, ideally exiting the opposite column. It is not recommended to use short locking screws as the goal is to attempt to incorporate as many fracture fragments as possible reaching the opposite column.

Step 10

Non-Locking, Locking or Multi-Directional Screws may now be used to fill the remaining screw holes (Step 10).

Specific instructions on inserting screws can be found in Appendix B pages 46-49.

30 | A.L.P.S. Elbow Fracture Plating System

The supine position with the arm across the chest.

Extensor Carpi Ulnaris Anconeus

Step 1

Direct posterior approach for radial head exposure.

Step 2

The Kocher interval approach, through the interval between the anconeus and the extensor carpi ulnaris muscles.

Exposing the Radial Head

Patient Positioning

The patient is placed in the supine position with the arm placed across the chest.

Step 1

The radial head may be approached from either a direct posterior skin incision (Step 1) in which a flap is raised to expose the radiocapitellar joint area or through a direct lateral approach. If there is a concurrent coronoid fracture or significant medial instability a single posterior incision is recommended.

Additionally, a posterior incision is placed through a watershed area between the medial and lateral cutaneous nerves and to avoid potential surgical trauma to these sensory nerves.

After the radiocapitellar area is exposed either through a direct lateral or posterior incision, there are two potential avenues of approach to the radial head.

Step 2

The most common approach is the Kocher interval approach which is through the interval between the anconeus and the extensor carpi ulnaris muscles. This approach avoids the radial nerve and its branches, and it is fairly easy to define (Step 2).

Note: A potential disadvantage is that the

Anconeus/Extensor Carpi Ulnaris interval will put the surgical approach directly over the lateral ulnar collateral ligament which is the main stabilizer of the lateral side of the elbow.

If the surgical approach is carried straight through the anconeus/extensor carpi ulnaris interval into the joint, the lateral ulnar collateral ligament can be violated.

The proper approach using the Kocher interval is to develop the interval between the anconeus and the extensor carpi ulnaris and then elevate anteriorly the extensor carpi ulnaris off of the lateral ulnar collateral ligament until the equator or midpoint of the radiocapitellar joint is exposed.

31 | A.L.P.S. Elbow Fracture Plating System

Extensor

Carpi Ulnaris M.

Fracture

Reduced

Capitulum

Anconeus M.

Step 3

Exposure of the radial head fracture.

Exposing the Radial Head (cont.)

Step 2 (cont.)

To preserve the integrity of the lateral ulnar collateral ligament complex, the capsule should be incised horizontally at the equator of the radiocapitellar joint.

Note: If the capsular incision is placed further posterior in the radiocapitellar joint, then potential violation of the lateral ulnar collateral ligament might occur.

Step 3

Once the radiocapitellar joint has been well exposed and the area of the posterior interosseous nerve protected, adequate exposure of the radial head fracture may be undertaken (Step 3).

If the fracture involves only a wedge of the radial head with the majority of the radial head intact, a buried 2.5 mm Non-Locking screw may be used to reduce and hold the small fragment.

In many fractures, the fracture occurs at the neck level with additional comminution of the radial head itself. In this situation, the radial neck area is often compressed and this needs to be elevated and fixed.

In addition to the Kocher interval approach, a more direct approach to the radial head that has recently become popular is a direct split of the common extensor tendon directly over the equator of the radiocapitellar joint. This incision is carried directly through the extensor digitorum communis to the level of the radiocapitellar joint capsule, and the capsule at this point of the equator of the radiocapitellar joint is incised to expose the radial head and neck. Fixation of the radial head and neck fracture is commenced as described previously.

32 | A.L.P.S. Elbow Fracture Plating System

Step 1

The plate is positioned using the Fragment Plate Holder.

Step 3

Drill through the F.A.S.T. Guide inserts with the 2.0 mm Drill Bit.

Step 2

The Plate Benders are used to tailor the plate to the individual patient anatomy.

Step 4

Remove the F.A.S.T. Guide inserts with the 1.3 mm Square Screwdriver.

Radial Head Fracture Fixation

Step 1

Use the Fragment Plate Holder (2312-07-012) to position the plate appropriately on the radial head.

The plates are designed to be placed in the area of the radial neck that should not impinge on the proximal radioulnar joint and off the articular surface of the radial head (Step 1).

Step 2

Two sizes of proximal radial plates are available, small and large. Select the most appropriate size to fit the individual. Use the supplied 2.5 Plate Benders (2312-

18-005) to tailor the fit of the plate to the individual anatomy of the patient (Step 2).

Note: For further information on plate bending refer to Appendix A on page 43.

Note: For small individuals the distal hole of the plate can be broken off to limit the distal exposure needed for plate fixation. It is recommended that a minimum of two screws be placed into the radial shaft.

The radial head and neck is then elevated and reduced into its normal position, and the plate is positioned.

The first screw can be applied into the shaft region to hold the plate in place. Screw selection will allow for either a Non-Locking or Locking screw to be placed through the plate. The standard Locking screw placed through the plate will provide good stability for the fracture construct.

Step 3

Drill through the F.A.S.T. Guide inserts with the

2.0 mm Drill Bit (FDB20) (Step 3).

Step 4

Remove the F.A.S.T. Guide inserts with the 1.3 mm

Square Screwdriver (2312-18-012) (Step 4).

33 | A.L.P.S. Elbow Fracture Plating System

Step 5

Measure the drilled hole by taking a direct reading from the NON-L line on the Depth Gauge.

Step 6

Insert the 2.5 mm Non-Locking Screw with the 1.3 mm

Square Driver coupled to the Quick Connect Handle.

Step 7

The 2.5 mm Counterbore can be used to create a recess where the screw head will sit below the level of the cortex.

Radial Head Fracture Fixation (cont.)

Step 5

Measure the drilled hole by taking a direct reading from the NON-L line on the Depth Gauge (2142-35-

100) (Step 5).

Note: When measuring for a Locking screw, the

Depth Gauge is used through the F.A.S.T. Guide inserts and measured off of the LOCK line. When inserting a Non-Locking screw, the F.A.S.T. Guide inserts is removed and the screw is measured off of the NON-L line.

Step 6

Insert the 2.5 mm Non-Locking Screw with the 1.3 mm

Square Driver coupled to the Quick Connect Handle

(QCH) (Step 6). The remaining screws (Locking or Non-

Locking) can now be placed starting with the radial head region.

Note: The plate should rest distal to the articular surface of the radial head surface and be positioned by hand in neutral rotation. The nonarticular region of the radial head and neck will now be facing laterally toward the surgeon.

Step 7

Small wedge fractures of the radial head will need to be fixed with a screw placed outside the plate. These screws should be placed through the radial head into the distal far cortex in an oblique fashion. It is not uncommon for one or two screws to be placed in this fashion, buried deep to the articular cartilage, for optimal fixation. The 2.5 mm Counterbore (2312-18-

014) can be used to create a recess where the screw head will sit below the level of the cortex (Step 7).

34 | A.L.P.S. Elbow Fracture Plating System

The supine position with the arm across the chest.

Medial Collateral

Ligament

Flexor Promator Group

Coronoid

Process

Fracture

Step 1

Medial approach for coronoid exposure.

Sublime

Tubercle

Ulnar Nerve

Step 2

Gently retract the ulnar nerve posteriorly.

Exposure of the Coronoid

If greater than 15 - 20% of the coronoid is fractured, internal fixation may be considered. The coronoid may potentially be approached from the lateral side if the radial head is significantly fractured and needs to be excised in preparation for radial head replacement.

Through the void in the radial head, the coronoid can often be visualized and with posteriorly directed screws (usually at least two screws), the coronoid may be secured.

In those cases when the radial head is not fractured or only partially fractured, it is recommended to approach the coronoid from the medial side.

Patient Positioning

The patient is placed in the supine position with the arm placed across the chest.

Step 1

In this situation with an isolated coronoid fracture, a medial approach is most efficient for operative exposure. Similar to a radial head fracture, either a direct posterior skin incision with elevation of a medial skin flap or a direct medial approach may be done to expose the coronoid (Step 1).

Step 2

After the skin incision, identify the ulnar nerve. This is then released in-situ to help positively identify it throughout the procedure and also to decompress it in case of post-operative swelling. Once the ulnar nerve is decompressed, exposure of the coronoid is achieved through the interval between the two heads of the flexor carpi ulnaris. It is easier to expose the coronoid by gently elevating the musculature of the flexor pronator group from the ulna from a distal to proximal direction.

35 | A.L.P.S. Elbow Fracture Plating System

Step 1

The plate is positioned using the Fragment Plate Holder.

Coronoid Fracture Fixation

While exposing the coronoid it is important to gently retract the ulnar nerve posteriorly (Step 2, previous page). As the soft tissue is elevated from the ulna from a distal to proximal direction, the sublime tubercle can be easily palpated and identified as the insertion site of the medial collateral ligament. The elevation of the flexor pronator group is continued in a distal to proximal direction, elevating the musculature off of the medial collateral ligament, allowing exposure of the capsule of the joint and coronoid. The entire flexor pronator origin does not need to be released for exposure of the coronoid, only a small posterior portion.

The joint capsule which is anterior to the medial collateral ligament can be excised. This will allow for good visualization of the coronoid for accurate reduction and fixation. The medial collateral ligament is preserved and only a small area of the origin of the flexor pronator group needs to be elevated to gain adequate exposure.

It should be noted that while elevating the musculature off of the ulna, care should be taken to identify any major branches of the ulnar nerve and protect them during exposure of the coronoid.

With the coronoid exposed, the appropriate plate is selected (right or left). It should be noted that the very medial edge of the ulna at the sublime tubercle makes a sharp almost 90-degree angle.

The plate will be placed at the apex of this significant angle on the ulna.

Step 1

Use the Fragment Plate Holder (2312-07-012) to position the plate appropriately on the coronoid fracture (Step 1).

36 | A.L.P.S. Elbow Fracture Plating System

Step 2

The plate is bent and fine tuned for the individual patient.

Step 3

Drill through the F.A.S.T. Guide inserts with the 2.0 mm Drill Bit.

Step 4

Remove the F.A.S.T. Guide inserts using the 1.3 mm Square Screwdriver.

Coronoid Fracture Fixation (cont.)

Step 2

Due to individual anatomic variations in patients, the plate will need to be bent and fine tuned for the individual patient (Step 2).

Note: For further information on plate bending refer to Appendix A on page 43.

Screw selection will allow for either a 2.5 mm Non-

Locking or Locking screw to be placed through the plate. In most situations, the standard Locking screw placed through the plate will provide good stability for the fracture construct.

One of the middle screws in the plate may be placed first for preliminary fixation of the implant.

Step 3

Drill through the F.A.S.T. Guide inserts with the 2.0 mm Drill Bit (FDB20) (Step 3).

Step 4

Remove the F.A.S.T. Guide inserts using the 1.3 mm

Square Screwdriver (2312-18-012) (Step 4).

37 | A.L.P.S. Elbow Fracture Plating System

Step 6

Measure the drilled hole by taking a direct reading from the NON-L line.

Step 7

Insert the 2.5 mm Non-Locking screw with the 1.3 mm

Square Driver coupled to the Quick Connect Handle.

Step 8

All screw holes should be filled to fully anchor the plate for optimal fixation.

Coronoid Fracture Fixation (cont.)

Step 6

Measure the drilled hole by taking a direct reading from the NON-L line on the depth gauge (2142-35-

100) (Step 6).

Step 7

Insert the 2.5 mm Non-Locking Screw with the 1.3 mm

Square Driver coupled to the Quick Connect Handle

(QCH) (Step 7).

Progressive screws are then placed. Locking screws do not require bicortical fixation through the posterior aspect of the ulna but should be placed deep enough for accurate and stable fixation of the coronoid fracture. It should be noted that the most proximal screw holes in the plate are angled to help avoid intraarticular penetration of screws.

The most lateral tab on the plate should be checked to be sure it is bent down and acting as a buttress on the very lateral aspect of the coronoid.

In a similar fashion, the very medial tab should be checked to be sure it is buttressing on the very medial aspect of the coronoid in the area of the sublime tubercle and the medial collateral ligament.

Fluoroscopic views should be taken to be sure there is no penetration of the screws into the joint, and similar to the radial head plate, the plate can be shortened by breaking off any unneeded segments of the plate.

Step 8

All screw holes should be filled to fully anchor the plate for optimal fixation (Step 8).

After placement of the plate has been accomplished, the elevated portion of the flexor pronator group is allowed to fall back together. The ulnar nerve is checked to be sure that it is unhindered, and the wound closed in standard fashion.

38 | A.L.P.S. Elbow Fracture Plating System

Ulnar Nerve

Step 1

Identification of the ulnar nerve.

Exposure of the Olecranon

The exposure for an olecranon fracture follows a standard posterior incision. Depending on the surgeon’s preference, the incision can be curved slightly laterally or medially over the tip of the olecranon itself. Once the skin incision is made, the fracture site is often quite evident.

Step 1

Elevation of the medial skin flap should be performed to accurately identify the ulnar nerve (Step 1). The ulnar nerve does not necessarily need to be released in situ or transposed but the area of the ulnar nerve should be recognized and protected throughout the procedure.

The olecranon fracture should be opened slightly and irrigated to remove any loose bone or hematoma.

Examination of the articular surface of the humerus may be performed if damage to the cartilage of the distal humerus is suspected.

39 | A.L.P.S. Elbow Fracture Plating System

Option 2 - Step 1

If no additional compression is needed, insert a K-wire through the home-run screw hole to cross the osteotomy site and secure the reduction.

Option 1

The more proximal prong on the clamp is used over the tip of the olecranon to reduce the fracture in place and a 2.0 mm

K-wire is placed in an oblique fashion across the fracture site.

Option 2 - Step 2

Insert the 3.5 mm locking screws with the T-15 Driver.

Olecranon Fracture Fixation

Reduction of the Olecranon

The olecranon fracture may be reduced using the surgeon's preferred method. Described are two options that may be considered.

Option 1: Clamp and K-wire combination

A drill or K-wire is used to create a small hole in either the lateral or medial cortex, 3 - 4 cm distal to the fracture site. This small hole in the ulna serves as a point where a prong of the clamp can grab on to the distal fragment. The opposite clamp prong is placed on the proximal fragment and the clamp is closed to reduce fragments. A 2.0 mm K-wire is then drilled in an oblique fashion lateral to medial, across the fracture site and to secure the reduction. Care should be taken to place the K-wire out of the way of the plate.

Option 2: Reduction through the plate

The fracture is reduced and a clamp is placed to hold the reduction as described in Option 1.

Step 1

The plate is then positioned on the fracture site.

A K-wire is drilled (using a K-wire Adapter placed in the

F.A.S.T. Guide inserts) through the home-run screw hole of the plate. The home-run screw hole may need to be contoured with the plate benders (2312-18-008) for optimal trajectory. An additional K-wire is then drilled into the distal fragment of the ulna.

Step 2

The twin proximal olecranon 3.5 mm Locking screws are inserted with the T-15 Driver coupled to the 2.0

Nm Torque-limiting Screwdriver Handle (2141-18-

001) or Bi-Directional Torque Limiting Power Adapter

(2312-18-020). Remove the K-wire from the home-run screw hole.

40 | A.L.P.S. Elbow Fracture Plating System

Step 3

Compression screw insertion preparation.

Step 4

A low profile 3.5 mm screw with a low profile washer is inserted by hand.

Step 5a

Arms can be broken off with the Plate Benders if not necessary.

Step 5

Fill screws in the shaft and coronoid area.

Olecranon Fracture Fixation (cont.)

Step 3

Drill the hole through the oblong active compression slot using the 2.7 mm Drill Bit (2142-27-070).

For very osteoporotic bone, use the 2.5 mm Drill Bit

(8290-29-070).

Note: The K-wire is removed just before the 3.5 mm

Compression Screw engages in the slot.

Step 4

The 3.5 mm low profile Non-Locking screw should be inserted into the Conversion Washer (1312-18-000) to allow it to perform active compression in the plate slot.

If the Conversion Washer is not used, the screw head will not be wide enough to engage the plate slot.

Insert the 3.5 mm Compression screw using the

2.2 mm Square Driver (8163-01-000). Remove the

K-wirein the distal portion of the ulna just before the head of the Compression screw engages with the compression slot.

Step 5

Insert a Compression screw through the home-run screw hole, and fill screws in the shaft and coronoid area as needed. Multiplanar arms may be contoured or broken off with the plate benders, (2312-18-008) if not thought to be necessary (Step 5a). Care should be taken when placing screws through the multiplanar side arms so that the appropriate length is selected, to avoid damage to the radial head.

Note: Arms should be broken off in the direction of the underside of the plate to prevent rough edges coming into contact with soft tissue.

Note: The plate may be bent and fine tuned for the individual patient. For further information on plate bending refer to Appendix A on page 42.

41 | A.L.P.S. Elbow Fracture Plating System

Appendix A

Contouring for Medial and Lateral Plates

Note: The benders are not intended to work with the shorter, rounder low profile F.A.S.T. Guide inserts. The benders are to be used only with the tall F.A.S.T. Guide inserts to contour the plate.

Medial/Lateral Plate Benders

1. Medial plate bent through a slot.

2. Distal end of medial plate bent towards medial condyle.

3. Planar bend at distal end of medial plate.

4. Lateral plate bent through a slot. 5. Planar bend at distal end of lateral plate.

Note: All bending features are designed to withstand a maximum total of 30 degrees of manipulation.

6. Distal end of lateral plate bent towards lateral condyle.

42 | A.L.P.S. Elbow Fracture Plating System

Appendix A

Contouring for Posterior Lateral and Olecranon Plates

Note: The benders are not intended to work with the shorter, rounder low profile F.A.S.T. Guide inserts. The benders are to be used only with the tall F.A.S.T. Guide inserts to contour the plate.

Posterior Lateral/Olecranon Plate Benders

1. Posterior lateral plate bent through a slot.

2. Planar bend applied to posterior lateral plate.

3. Lateral tab of posterior lateral plate bent toward the bone.

4. Olecranon plate bent through a slot.

5. Planar bend applied to olecranon plate.

6. If necessary, the benders can be used to break off the arms of the olecranon plate.

Appendix A

Contouring for Coronoid and Radius Plates

43 | A.L.P.S. Elbow Fracture Plating System

Coronoid/Radius Plate Benders

1. Planar bend applied to coronoid plate.

2. Lateral tab of coronoid plate bent toward the bone.

3. Planar bend applied to the shaft of proximal radius plate.

4. Planar bend applied to the arms of proximal radius plate.

44 | A.L.P.S. Elbow Fracture Plating System

Appendix A

Concave/Convex Contouring for Long Plates

The long plate benders are used to contour the shaft portion of the long implants. Benders consist of three bending features: the foot, the slot, and the plantar bending feature (teeth).

Using the “feet” of the benders the plates can be contoured to conform to the patient’s unique anatomic needs. The foot of the bender is placed inside the slotted section of the plate and engaged on the underside of the plate. The benders can be used either facing or opposing each other to create concave or convex bends. When creating convex bends there must be at least one empty slot inbetween benders to ensure there is no thread deformation of locking hole.

Bender "Feet"

Concave Bend Convex Bend

Appendix A

Axial Contouring for Long Plates

Using the “slot” of the benders the plates can be contoured to in the axial direction. Insert plate into

“slots” and rotate benders away from each other to impart twist.

45 | A.L.P.S. Elbow Fracture Plating System

Planar Contouring for Long Plates –

Olecranon ONLY

The longer olecranon plates are left and right specific to meet the needs of ulnar anatomy. There is a contouring feature built into the longer olecranon plates to allow the plate to be curved to match the patient’s anatomy while maintaining strength.

To apply planar bend, use “teeth” of the benders.

Insert “teeth” of benders to slots adjacent to waist feature of olecranon plates; pull benders away from one another to impart planar bend.

Axial Bend

Planar Bend

46 | A.L.P.S. Elbow Fracture Plating System

Appendix B

Non-Locking Screw Insertion

Step 1

Remove the F.A.S.T. Guide inserts using the T-15 Driver.

Step 2

Drill through both cortices with the 2.7 mm Drill Bit.

Step 3

Take a direct reading from the NON-L line.

Step 4

Insert by hand using the

Black Ratchet Handle with the 2.2 mm Square Driver.

Step 1

If Non-Locking Screws are to be used, the F.A.S.T.

Guide inserts are removed using the T-15 Driver

(2142-15-070) (Step 1).

Step 2

Insert the Drill Guide into the screw hole and drill through both cortices with the 2.7 mm Drill Bit (2142-

27-070) (Step 2).

Step 3

Measure the drilled hole by taking a direct reading from the NON-L line on the Depth Gauge (2142-35-

100) (Step 3).

Step 4

The screw is inserted by hand using the Black Ratchet

Handle (8261-66-000) with the 2.2 mm Square Driver

(8163-01-000) (Step 4).

Appendix B

Non-Locking Screw Insertion (Compression Mode)

47 | A.L.P.S. Elbow Fracture Plating System

Step 1

Drill through both cortices with the 2.7 mm Drill Bit.

Step 3

Engage the appropriate 3.5 mm Low

Profile Non-Locking screw with the

2.2 mm Square Driver.

Step 2

Take a direct reading from the NON-L line.

Step 4

Insert by hand using the Black Ratchet Handle with the 2.2 mm Square Driver.

If the compression hole is to be used, a low profile

Non-Locking screw must be used in conjunction with a low-profile washer. This will convert the low-profile screw to a standard profile Non-Locking screw.

Step 1

Insert the Drill Guide into the screw hole and drill through both cortices with the 2.7 mm Drill Bit (2142-

27-070). Drill eccentricly in the slot furthest away from the fracture (Step 1).

Step 2

Measure the drilled hole by taking a direct reading from the NON-L line on the Depth Gauge (Step 2).

Step 3

Engage the appropriate 3.5 mm low profile Non-

Locking screw with the 2.2 mm Square Driver (8163-

01-000). Once engaged, the screw is placed through the Low Profile Washer (1312-18-000), which is in the cartridge, and pressure applied until an audible click is heard. Once the assembly is mated correctly, the screw can be advanced into the compression hole of the plate. Slide the screw down the cartridge remove and insert into the active compression slot (Step 3).

Step 4

The screw is inserted by hand using the Black Ratchet

Handle (8261-66-000) with the 2.2 mm Square Driver

(8163-01-000) (Step 4).

Note: The washer is for use ONLY with the 3.5 mm low profile Non-Locking screw.

48 | A.L.P.S. Elbow Fracture Plating System

Appendix B

Locking Screw Insertion

Step 1

Drill through the F.A.S.T. Guide inserts with the

2.7 mm Drill Bit.Slide the Measuring Drill Sleeve to the top end of the F.A.S.T. Guide inserts insert and read the measurement of the Locking Screw length from the proximal end.

Step 1

Slide the Measuring Drill Sleeve (8163-01-005) onto the 2.7 mm Drill Bit 2142-27-070). Drill through the

F.A.S.T. Guide inserts until the far cortex is reached.

Slide the Measuring Drill Sleeve onto the top end of the F.A.S.T. Guide inserts and read the measurement of the Locking Screw length from the proximal end of the Drill Measuring Sleeve (Step 1).

Note: If a second method of measurement is desired, remove the F.A.S.T. Guide inserts, then measure the drilled hole by taking a direct reading from the LOCK line on the Depth Gauge.

Step 2

Remove the F.A.S.T. Guide inserts using the T-15 Driver.

Step 2

Step 3

Insert the 3.5 mm Locking Screw with the T-15 Driver coupled to the 2.0 Nm

Torque-Limiting Screwdriver Handle or Bi-Directional Torque Limiting

Power Adapter.

Remove the F.A.S.T. Guide inserts using the T-15 Driver

(2142-15-070) (Step 2).

Step 3

Insert the 3.5 mm locking screw with the T-15 Driver

(2142-15-070) coupled to the 2.0 Nm Torque-Limiting

Screwdriver Handle (2141-18-001) or Bi-Directional

Torque Limiting Power Adapter (2312-18-020) (Step 3).

Once the screw is seated, an audible click will be heard from the driver noting that the screw is fully seated.

Appendix B

Multi-Directional Screw Insertion (MDS)

49 | A.L.P.S. Elbow Fracture Plating System

25 degrees of angulation

Step 1

Remove the F.A.S.T. Guide inserts using the T-15 Driver.

Step 2

Drill using the 2.7 mm Drill Bit through the Drill Guide.

Step 3

Take a direct reading from the LOCK line.

Step 4a

Insert the MDS screw under power using the 2.2 mm Square

Driver coupled to the Torque

Limiting Power Adapter.

Step 1

The MDS screw is inserted by removing the F.A.S.T.

Guide inserts using the T-15 Driver (2142-15-070) or the Short T-15 Driver (2312-18-021) (Step 1).

Step 2

Drill using the 2.7 mm Drill Bit (2142-27-070). The drill bit can be angled up to a 25 degree cone of angulation and still have the screw lock into the plate

(Step 2).

Step 3

Measure the drilled hole with the Depth Gauge (2142-

35-100) by taking a direct reading from the LOCK line on the Depth Gauge (Step 3).

Step 4 (diagram not shown)

Insert the 3.5 mm MDS screw with the 2.2 mm

Square Driver (8163-01-000) coupled to the 2.0 Nm

Torque-Limiting Screwdriver Handle (2141-18-001).

Step 4a

Alternatively, the screw may be inserted under power using the 2.2 mm Square Driver (8163-01-000) coupled to the Torque Limiting Power Adapter (2312-

18-020) (Step 4a).

Once the screw is seated, an audible click will be heard from the driver noting that the screw is fully seated.

50 | A.L.P.S. Elbow Fracture Plating System

Appendix C

Screw Removal

Step 1 Step 2

Note: Plate screws will often compete for space in a tight area, and the screws can often interdigitate with each other. This is especially relevant with the three distal screws on the Lateral and Medial plates

(Step 1).

Therefore, it is important to remove the screws in reverse order (last in, first out), to limit breaking the heads from the screws.

If the order of the screw placement is not known, the following procedure is recommended (Step 2):

1. Attempt to remove a screw. If it stalls within a turn or two, retighten using the Bi-Directional Torque

Limiting Power Adapter.

Note: This is very important, as this screw may be interdigitated with another screw, which may cause difficulty during removal. It is critical to retighten the screw prior to moving on to the next screw as described in Step 2, otherwise both screws will be difficult to remove.

2. Move on to the next screw and repeat Step 1.

3. Keep moving from one screw to the next until all have been removed.

Instrument Trays

The A.L.P.S. Elbow Plating System

51 | A.L.P.S. Elbow Fracture Plating System

52 | A.L.P.S. Elbow Fracture Plating System

Instrument Trays

1

2

3

4

5

8

9

10

11

12

6

7

13

Instrument Tray

Non-Sterile

1. 2312-18-003

2. 2312-18-004

3. 2312-18-008 (2)

4. 14179-6 (12)

5. 2142-35-100

6. 9399-99-435

7. 8163-01-005 (2)

8. 8290-29-070 (2)

9. 8290-32-070 (2)

10. 2142-27-070 (3)

11. 8163-01-000 (2)

12. 2142-15-070 (2)

13. 2312-18-007 (3)

14. 1920.

15. 2312-18-020

16. 2142-13-567

17. 2141-18-001

18. 13577 (2)

19. 8261-66-000

NP. 2312-18-021

3.5 Medial/Lateral Straight Bender

3.5 Medial/Lateral L Bender

3.5 Post. Lateral/Olecranon Bender

2.0 mm K-wire

Small Frag Depth Gauge

Double Drill Guide 2.7/2.0mm

Drill Measuring Sleeve

Drill Bit 2.5 mm

Drill Twist S-Couple 3.5 x 70 mm

2.7 mm Calibrated Drill Bit

2.2 mm Square Screwdriver

T-15 Tapered Driver

2.0 mm K-wire Adapter

Periarticular Reduction Instrument Lg

2.0 mm Torque Limiting Power Adapter

Plate End Retractor

Small Torque Limiting Handle

Reduction Forcep W/Points Lg

Cannulated Ratchet Handle

T-15 Tapered Driver Short (Optional Instrument)

14

17

18

15

16

19

53 | A.L.P.S. Elbow Fracture Plating System

Non-Sterile Implants

1 2

3

9

11

13

5

7

4

10

12

14

6

8

Non-Sterile Implant Tray

Medial Plates

1. 1312-18-703 (4) 10 Hole - Left

2. 1312-18-701 (4) 10 Hole - Right

3. 1312-18-702 (4) 9 Hole - Left

4. 1312-18-700 (4) 9 Hole - Right

Lateral Plates

5. 1312-18-202 (2) 7 Hole - Left

6. 1312-18-200 (2) 7 Hole - Right

7. 1312-18-203 (2) 9 Hole - Left

8. 1312-18-201 (2) 9 Hole - Right

Posterior Lateral Plates

9. 1312-18-302 (2) 9 Hole - Left

10. 1312-18-300 (2) 9 Hole - Right

11. 1312-18-303 (2) 11 Hole - Left

12. 1312-18-301 (2) 11 Hole - Right

Olecranon Plates

13. 1312-18-600 (2) 10 Hole - Small

14. 1312-18-601 (2) 13 Hole - Large

*Special Order

Non-Sterile Long Plate Module

Medial Plates

1312-18-704 13 Hole - 127 mm Right

1312-18-707 13 Hole - 127 mm Left

1312-18-705 17 Hole - 166 mm Right

1312-18-708 17 Hole - 166 mm Left

Lateral Plates

1312-18-204 11 Hole - 103 mm Right

1312-18-207 11 Hole - 103 mm Left

1312-18-205 15 Hole - 142 mm Right

1312-18-208 15 Hole - 142 mm Left

Posterior Lateral Plates

1312-18-305 17 Hole - 148 mm Right

1312-18-308 17 Hole - 148 mm Left

1312-18-800 21 Hole - 210 mm Right

1312-18-803 21 Hole - 210 mm Left

1312-18-801 25 Hole - 250 mm Right

1312-18-804 25 Hole - 250 mm Left

Olecranon Plates

1312-18-604 17 Hole - 154 mm Right

1312-18-607 17 Hole - 154 mm Left

1312-18-606 21 Hole - 194 mm Right*

1312-18-609 21 Hole - 194 mm Left*

Instruments - Non-Sterile

2312-18-016 Short F.A.S.T. Guide inserts (10)

2312-18-001 Long Plate Bender (2)

2142-07-027 2.7 mm Locking Drill Guide (1)

54 | A.L.P.S. Elbow Fracture Plating System

1

2

5 6

3 4

8

9

10

7

11

12

13

Non-Sterile 2.5 mm Implant Module

Proximal Radius Plates

1. 1312-18-400 (2) Small

2. 1312-18-401 (2) Large

Coronoid Plates

3. 1312-18-501 (2) Left

4. 1312-18-500 (2) Right

5. 2.5 mm Non-locking Screw

SP14000 Peg Screw 2.5 x 14 mm

SP16000 Peg Screw 2.5 x 16 mm

SP18000 Peg Screw 2.5 x 18 mm

SP20000 Peg Screw 2.5 x 20 mm

SP22000 Peg Screw 2.5 x 22 mm

SP24000 Peg Screw 2.5 x 24 mm

SP26000 Peg Screw 2.5 x 26 mm

SP28000 Peg Screw 2.5 x 28 mm

SP30000 Peg Screw 2.5 x 30 mm

SP32000 Peg Screw 2.5 x 32 mm

SP34000 Peg Screw 2.5 x 34 mm

SP36000 Peg Screw 2.5 x 36 mm

SP38000 Peg Screw 2.5 x 38 mm

SP40000 Peg Screw 2.5 x 40 mm

FP28

FP30

FP32

FP34

FP36

FP38

FP40

6. 2.5 mm Locking Screw

FP14 Peg Full Thread 2.5 x 14 mm

FP16

FP18

Peg Full Thread 2.5 x 16 mm

Peg Full Thread 2.5 x 18 mm

FP20

FP22

FP24

FP26

Peg Full Thread 2.5 x 20 mm

Peg Full Thread 2.5 x 22 mm

Peg Full Thread 2.5 x 24 mm

Peg Full Thread 2.5 x 26 mm

Peg Full Thread 2.5 x 28 mm

Peg Full Thread 2.5 x 30 mm

Peg Full Thread 2.5 x 32 mm

Peg Full Thread 2.5 x 34 mm

Peg Full Thread 2.5 x 36 mm

Peg Full Thread 2.5 x 38 mm

Peg Full Thread 2.5 x 40 mm

7. 14425-6 (12)

8. FDB20 (2)

1.6 mm x 6 in. K-wire Half Bay

F.A.S.T. Drill Bit 2.0

9. 2312-18-012 (2) 1.3 mm Square Screwdriver

10. QCH Quick Connect Handle

11. 2312-18-014

12. 2312-07-012

2.5 mm Counterbore

Fragment Plate Holder

13. 2312-18-005 (2) 2.5 mm Bender

55 | A.L.P.S. Elbow Fracture Plating System

1

2

3 4

Non-Sterile 3.5 mm Screw Module

1. 3.5 mm Locking Cortical Screw

8161-35-010 3.5 mm Cortical Locking Screw 10 mm

8161-35-012 3.5 mm Cortical Locking Screw 12 mm

8161-35-014 3.5 mm Cortical Locking Screw 14 mm

8161-35-016 3.5 mm Cortical Locking Screw 16 mm

8161-35-018 3.5 mm Cortical Locking Screw 18 mm

8161-35-020 3.5 mm Cortical Locking Screw 20 mm

8161-35-022 3.5 mm Cortical Locking Screw 22 mm

8161-35-024 3.5 mm Cortical Locking Screw 24 mm

8161-35-026 3.5 mm Cortical Locking Screw 26 mm

8161-35-028 3.5 mm Cortical Locking Screw 28 mm

8161-35-030 3.5 mm Cortical Locking Screw 30 mm

8161-35-032 3.5 mm Cortical Locking Screw 32 mm

8161-35-034 3.5 mm Cortical Locking Screw 34 mm

8161-35-036 3.5 mm Cortical Locking Screw 36 mm

8161-35-038 3.5 mm Cortical Locking Screw 38 mm

8161-35-040 3.5 mm Cortical Locking Screw 40 mm

8161-35-042 3.5 mm Cortical Locking Screw 42 mm

8161-35-044 3.5 mm Cortical Locking Screw 44 mm

8161-35-046 3.5 mm Cortical Locking Screw 46 mm

8161-35-048 3.5 mm Cortical Locking Screw 48 mm

8161-35-050 3.5 mm Cortical Locking Screw 50 mm

8161-35-052 3.5 mm Cortical Locking Screw 52 mm

8161-35-054 3.5 mm Cortical Locking Screw 54 mm

8161-35-056 3.5 mm Cortical Locking Screw 56 mm

8161-35-058 3.5 mm Cortical Locking Screw 58 mm

8161-35-060 3.5 mm Cortical Locking Screw 60 mm

8161-35-065 3.5 mm Cortical Locking Screw 65 mm

8161-35-070 3.5 mm Cortical Locking Screw 70 mm

2. Multi-Directional Screw

8163-35-020 3.5 mm Multi-Directional Screw 20 mm

8163-35-022 3.5 mm Multi-Directional Screw 22 mm

8163-35-024 3.5 mm Multi-Directional Screw 24 mm

8163-35-026 3.5 mm Multi-Directional Screw 26 mm

8163-35-028 3.5 mm Multi-Directional Screw 28 mm

8163-35-030 3.5 mm Multi-Directional Screw 30 mm

8163-35-032 3.5 mm Multi-Directional Screw 32 mm

8163-35-034 3.5 mm Multi-Directional Screw 34 mm

8163-35-036 3.5 mm Multi-Directional Screw 36 mm

8163-35-038 3.5 mm Multi-Directional Screw 38 mm

8163-35-040 3.5 mm Multi-Directional Screw 40 mm

8163-35-042 3.5 mm Multi-Directional Screw 42 mm

8163-35-044 3.5 mm Multi-Directional Screw 44 mm

8163-35-046 3.5 mm Multi-Directional Screw 46 mm

8163-35-048 3.5 mm Multi-Directional Screw 48 mm

8163-35-050 3.5 mm Multi-Directional Screw 50 mm

8163-35-052 3.5 mm Multi-Directional Screw 52 mm

8163-35-054 3.5 mm Multi-Directional Screw 54 mm

8163-35-056 3.5 mm Multi-Directional Screw 56 mm

8163-35-058 3.5 mm Multi-Directional Screw 58 mm

8163-35-060 3.5 mm Multi-Directional Screw 60 mm

56 | A.L.P.S. Elbow Fracture Plating System

3 4

Non-Sterile 3.5 mm Screw Module (cont.)

3. 3.5 mm Low Profile Cortical Screw

1312-18-014 3.5 mm Low Profile Cortical 14 mm

1312-18-016 3.5 mm Low Profile Cortical 16 mm

1312-18-018 3.5 mm Low Profile Cortical 18 mm

1312-18-020 3.5 mm Low Profile Cortical 20 mm

1312-18-022 3.5 mm Low Profile Cortical 22 mm

1312-18-024 3.5 mm Low Profile Cortical 24 mm

1312-18-026 3.5 mm Low Profile Cortical 26 mm

1312-18-028 3.5 mm Low Profile Cortical 28 mm

1312-18-030 3.5 mm Low Profile Cortical 30 mm

1312-18-032 3.5 mm Low Profile Cortical 32 mm

1312-18-034 3.5 mm Low Profile Cortical 34 mm

1312-18-036 3.5 mm Low Profile Cortical 36 mm

1312-18-038 3.5 mm Low Profile Cortical 38 mm

1312-18-040 3.5 mm Low Profile Cortical 40 mm

1312-18-042 3.5 mm Low Profile Cortical 42 mm

1312-18-044 3.5 mm Low Profile Cortical 44 mm

1312-18-046 3.5 mm Low Profile Cortical 46 mm

1312-18-048 3.5 mm Low Profile Cortical 48 mm

1312-18-050 3.5 mm Low Profile Cortical 50 mm

1312-18-055 3.5 mm Low Profile Cortical 55 mm

1312-18-060 3.5 mm Low Profile Cortical 60 mm

1312-18-065 3.5 mm Low Profile Cortical 65 mm

1312-18-070 3.5 mm Low Profile Cortical 70 mm

1312-18-075 3.5 mm Low Profile Cortical 75 mm

4. Low Profile Cortical Washer

1312-18-000 3.5 mm Low Profile Cortical Washer

Sterile Implants

2.5 mm Non-locking Screw, Sterile

1312-12-514 Peg Screw 2.5 x 14 mm

1312-12-516 Peg Screw 2.5 x 16 mm

1312-12-518 Peg Screw 2.5 x 18 mm

1312-12-520 Peg Screw 2.5 x 20 mm

1312-12-522 Peg Screw 2.5 x 22 mm

1312-12-524 Peg Screw 2.5 x 24 mm

1312-12-526 Peg Screw 2.5 x 26 mm

1312-12-528 Peg Screw 2.5 x 28 mm

1312-12-530 Peg Screw 2.5 x 30 mm

1312-12-532 Peg Screw 2.5 x 32 mm

1312-12-534 Peg Screw 2.5 x 34 mm

1312-12-536 Peg Screw 2.5 x 36 mm

1312-12-538 Peg Screw 2.5 x 38 mm

1312-12-540 Peg Screw 2.5 x 40 mm

2.5 mm Locking Screw, Sterile

1312-12-614 Peg Full Thread 2.5 x 14 mm

1312-12-616 Peg Full Thread 2.5 x 16 mm

1312-12-618 Peg Full Thread 2.5 x 18 mm

1312-12-620 Peg Full Thread 2.5 x 20 mm

1312-12-622 Peg Full Thread 2.5 x 22 mm

1312-12-624 Peg Full Thread 2.5 x 24 mm

1312-12-626 Peg Full Thread 2.5 x 26 mm

1312-12-628 Peg Full Thread 2.5 x 28 mm

1312-12-630 Peg Full Thread 2.5 x 30 mm

1312-12-632 Peg Full Thread 2.5 x 32 mm

1312-12-634 Peg Full Thread 2.5 x 34 mm

1312-12-636 Peg Full Thread 2.5 x 36 mm

1312-12-638 Peg Full Thread 2.5 x 38 mm

1312-12-640 Peg Full Thread 2.5 x 40 mm

3.5 mm Low Profile Cortical Screw, Sterile

8512-35-014 3.5 mm Low Profile Cortical 14 mm

8512-35-016 3.5 mm Low Profile Cortical 16 mm

8512-35-018 3.5 mm Low Profile Cortical 18 mm

8512-35-020 3.5 mm Low Profile Cortical 20 mm

8512-35-022 3.5 mm Low Profile Cortical 22 mm

8512-35-024 3.5 mm Low Profile Cortical 24 mm

8512-35-026 3.5 mm Low Profile Cortical 26 mm

8512-35-028 3.5 mm Low Profile Cortical 28 mm

8512-35-030 3.5 mm Low Profile Cortical 30 mm

8512-35-032 3.5 mm Low Profile Cortical 32 mm

8512-35-034 3.5 mm Low Profile Cortical 34 mm

8512-35-036 3.5 mm Low Profile Cortical 36 mm

8512-35-038 3.5 mm Low Profile Cortical 38 mm

8512-35-040 3.5 mm Low Profile Cortical 40 mm

8512-35-042 3.5 mm Low Profile Cortical 42 mm

8512-35-044 3.5 mm Low Profile Cortical 44 mm

8512-35-046 3.5 mm Low Profile Cortical 46 mm

8512-35-048 3.5 mm Low Profile Cortical 48 mm

8512-35-050 3.5 mm Low Profile Cortical 50 mm

8512-35-055 3.5 mm Low Profile Cortical 55 mm

8512-35-060 3.5 mm Low Profile Cortical 60 mm

8512-35-065 3.5 mm Low Profile Cortical 65 mm

8512-35-070 3.5 mm Low Profile Cortical 70 mm

8512-35-075 3.5 mm Low Profile Cortical 75 mm

57 | A.L.P.S. Elbow Fracture Plating System

Low Profile Cortical Washer, Sterile

8512-18-000 3.5 mm Low Profile Cortical Washer

2.7 mm Locking Cortical Screw, Sterile

8563-27-010 2.7 mm Cortical Locking Screw 10 mm

8563-27-012 2.7 mm Cortical Locking Screw 12 mm

8563-27-014 2.7 mm Cortical Locking Screw 14 mm

8563-27-016 2.7 mm Cortical Locking Screw 16 mm

8563-27-018 2.7 mm Cortical Locking Screw 18 mm

8563-27-020 2.7 mm Cortical Locking Screw 20 mm

8563-27-022 2.7 mm Cortical Locking Screw 22 mm

8563-27-024 2.7 mm Cortical Locking Screw 24 mm

8563-27-026 2.7 mm Cortical Locking Screw 26 mm

8563-27-028 2.7 mm Cortical Locking Screw 28 mm

8563-27-030 2.7 mm Cortical Locking Screw 30 mm

8563-27-032 2.7 mm Cortical Locking Screw 32 mm

8563-27-034 2.7 mm Cortical Locking Screw 34 mm

8563-27-036 2.7 mm Cortical Locking Screw 36 mm

8563-27-038 2.7 mm Cortical Locking Screw 38 mm

8563-27-040 2.7 mm Cortical Locking Screw 40 mm

8563-27-042 2.7 mm Cortical Locking Screw 42 mm

8563-27-044 2.7 mm Cortical Locking Screw 44 mm

8563-27-046 2.7 mm Cortical Locking Screw 46 mm

8563-27-048 2.7 mm Cortical Locking Screw 48 mm

8563-27-050 2.7 mm Cortical Locking Screw 50 mm

3.5 mm Locking Cortical Screw, Sterile

8561-35-010 3.5 mm Cortical Locking Screw 10 mm

8561-35-012 3.5 mm Cortical Locking Screw 12 mm

8561-35-014 3.5 mm Cortical Locking Screw 14 mm

8561-35-016 3.5 mm Cortical Locking Screw 16 mm

8561-35-018 3.5 mm Cortical Locking Screw 18 mm

8561-35-020 3.5 mm Cortical Locking Screw 20 mm

8561-35-022 3.5 mm Cortical Locking Screw 22 mm

8561-35-024 3.5 mm Cortical Locking Screw 24 mm

8561-35-026 3.5 mm Cortical Locking Screw 26 mm

8561-35-028 3.5 mm Cortical Locking Screw 28 mm

8561-35-030 3.5 mm Cortical Locking Screw 30 mm

8561-35-032 3.5 mm Cortical Locking Screw 32 mm

8561-35-034 3.5 mm Cortical Locking Screw 34 mm

8561-35-036 3.5 mm Cortical Locking Screw 36 mm

8561-35-038 3.5 mm Cortical Locking Screw 38 mm

8561-35-040 3.5 mm Cortical Locking Screw 40 mm

8561-35-042 3.5 mm Cortical Locking Screw 42 mm

8561-35-044 3.5 mm Cortical Locking Screw 44 mm

8561-35-046 3.5 mm Cortical Locking Screw 46 mm

8561-35-048 3.5 mm Cortical Locking Screw 48 mm

8561-35-050 3.5 mm Cortical Locking Screw 50 mm

8561-35-052 3.5 mm Cortical Locking Screw 52 mm

8561-35-054 3.5 mm Cortical Locking Screw 54 mm

8561-35-056 3.5 mm Cortical Locking Screw 56 mm

8561-35-058 3.5 mm Cortical Locking Screw 58 mm

8561-35-060 3.5 mm Cortical Locking Screw 60 mm

8561-35-065 3.5 mm Cortical Locking Screw 65 mm

8561-35-070 3.5 mm Cortical Locking Screw 70 mm

58 | A.L.P.S. Elbow Fracture Plating System

Sterile Implants & Instruments

Multi-Directional Screw, Sterile

8563-35-020 3.5 mm Multi-Directional Screw 20 mm

8563-35-022 3.5 mm Multi-Directional Screw 22 mm

8563-35-024 3.5 mm Multi-Directional Screw 24 mm

8563-35-026 3.5 mm Multi-Directional Screw 26 mm

8563-35-028 3.5 mm Multi-Directional Screw 28 mm

8563-35-030 3.5 mm Multi-Directional Screw 30 mm

8563-35-032 3.5 mm Multi-Directional Screw 32 mm

8563-35-034 3.5 mm Multi-Directional Screw 34 mm

8563-35-036 3.5 mm Multi-Directional Screw 36 mm

8563-35-038 3.5 mm Multi-Directional Screw 38 mm

8563-35-040 3.5 mm Multi-Directional Screw 40 mm

8563-35-042 3.5 mm Multi-Directional Screw 42 mm

8563-35-044 3.5 mm Multi-Directional Screw 44 mm

8563-35-046 3.5 mm Multi-Directional Screw 46 mm

8563-35-048 3.5 mm Multi-Directional Screw 48 mm

8563-35-050 3.5 mm Multi-Directional Screw 50 mm

8563-35-052 3.5 mm Multi-Directional Screw 52 mm

8563-35-054 3.5 mm Multi-Directional Screw 54 mm

8563-35-056 3.5 mm Multi-Directional Screw 56 mm

8563-35-058 3.5 mm Multi-Directional Screw 58 mm

8563-35-060 3.5 mm Multi-Directional Screw 60 mm

Disposables, Sterile

8295-16-150 1.6 mm Steinman Pin Bayonet Tip

2312-01-301 Drill Bit F.A.S.T. 2.0 mm

2312-18-023 2.7 mm Short F.A.S.T. Guide, Left

2312-18-024 2.7 mm Short F.A.S.T. Guide, Right

2312-18-025 2.7 mm Short F.A.S.T. Guide, Bilateral

Lateral Plates, Sterile

8513-18-200 Distal Humeral Lateral Plate, 7 hole right

8513-18-201 Distal Humeral Lateral Plate, 9 hole right

8513-18-202 Distal Humeral Lateral Plate, 7 hole left

8513-18-203 Distal Humeral Lateral Plate, 9 hole left

8513-18-204 Distal Humeral Lateral Plate, 11 hole right

8513-18-205 Distal Humeral Lateral Plate, 15 hole right

8513-18-207 Distal Humeral Lateral Plate, 11 hole left

8513-18-208 Distal Humeral Lateral Plate, 15 hole left

Posterior Lateral Plates, Sterile

8513-18-300 Distal Humeral Posterior Lateral Plate, 9 hole right

8513-18-301 Distal Humeral Posterior Lateral Plate, 11 hole right

8513-18-302 Distal Humeral Posterior Lateral Plate, 9 hole left

8513-18-303 Distal Humeral Posterior Lateral Plate, 11 hole left

8513-18-305 Distal Humeral Posterior Lateral Plate, 17 hole right

8513-18-308 Distal Humeral Posterior Lateral Plate, 17 hole left

8513-18-800 Distal Humeral Posterior Lateral Plate, 21 hole right

8513-18-801 Distal Humeral Posterior Lateral Plate, 25 hole right

8513-18-803 Distal Humeral Posterior Lateral Plate, 21 hole left

8513-18-804 Distal Humeral Posterior Lateral Plate, 25 hole left

Proximal Radius Plates, Sterile

8513-18-400 Proximal Radius Plate Small

8513-18-401 Proximal Radius Plate Large

Coronoid Plates, Sterile

8513-18-500 Coronoid Plate, Right

8513-18-501 Coronoid Plate, Left

Olecranon Plates, Sterile

8513-18-600 Olecranon Plate Small, 10 Hole

8513-18-601 Olecranon Plate Large, 13 Hole

8513-18-604 Olecranon Plate Right, 17 Hole

8513-18-606 Olecranon Plate Right, 21 Hole

8513-18-607 Olecranon Plate Left, 17 Hole

8513-18-609 Olecranon Plate Left, 21 Hole

Medial Plates, Sterile

8513-18-700 Distal Humeral Medial Plate, 9 hole right

8513-18-701 Distal Humeral Medial Plate, 10 hole right

8513-18-702 Distal Humeral Medial Plate, 9 hole left

8513-18-703 Distal Humeral Medial Plate, 10 hole left

8513-18-704 Distal Humeral Medial Plate, 13 hole right

8513-18-705 Distal Humeral Medial Plate, 17 hole right

8513-18-707 Distal Humeral Medial Plate, 13 hole left

8513-18-708 Distal Humeral Medial Plate, 17 hole left

Non-Sterile Trials

Lateral

2312-18-200 Distal Humeral Lateral Right Plate Trial, 7 Hole

2312-18-202 Distal Humeral Lateral Left Plate Trial, 7 Hole

Posterior Lateral

2312-18-300 Distal Humeral Posterior Lateral Right Plate Trial, 9 Hole

2312-18-302 Distal Humeral Posterior Lateral Left Plate Trial, 9 Hole

Proximal Radius

2312-18-400 Proximal Radius Plate Trial

Coronoid

2312-18-500 Coronoid Plate Right Trial

2312-18-501 Coronoid Plate Left Trial

Olecranon

2312-18-600 Olecranon Plate Trial, 10 Hole

Medial

2312-18-700 Distal Humerus Medial Right Plate Trial, 9 Hole

2312-18-702 Distal Humerus Medial Left Plate Trial, 9 Hole

59 | A.L.P.S. Elbow Fracture Plating System

60 | A.L.P.S. Elbow Fracture Plating System

INDICATIONS

The A.L.P.S. Elbow Plating Systen is indicated for fixaiton of fractures, fusions, osteotomies, and non-unions of the clavicle, humerus, radius, ulna, olecranon, metacarpal, metatarsal, malleolus, tibia and fibula, particularly in osteopenic bone.

CONTRAINDICATIONS

Screws, plates, intramedullary nails, compression hip screws, pins and wires are contraindicated in: active infection, conditions which tend to retard healing such as blood supply limitations, previous infections, insufficient quantity or quality of bone to permit stabilization of the fracture complex and/ or fusion of the joints, conditions that restrict the patient’s ability or willingness to follow postoperative instructions during the healing process, foreign body sensitivity, and cases where the implant(s) would cross open epiphyseal plates in skeletally immature patients.

ADDITIONAL CONTRAINDICATION FOR

ORTHOPAEDIC SCREWS AND PLATES ONLY

Cases with malignant primary or metastatic tumors which preclude adequate bone support or screw fixations, unless supplemental fixation or stabilization methods are utilized.

Reference

1. DVA-107504-DVER. Data on file at Biomet. Mechanical testing not necessarily indicative of clinical performance

This material is intended for healthcare professionals and the Zimmer

Biomet sales force. Distribution to any other recipient is prohibited.

For indications, contraindications, warnings, precautions, potential adverse effects and patient counseling information, see the package insert or contact your local representative; visit www.zimmerbiomet.

com for additional product information. All content herein is protected by copyright, trademarks and other intellectual property rights, as applicable, owned by or licensed to Zimmer Biomet or its affiliates unless otherwise indicated, and must not be redistributed, duplicated or disclosed, in whole or in part, without the express written consent of

Zimmer Biomet.

For indications, contraindications, warnings, precautions, potential adverse effects and patient counseling information, see the package insert or contact your local representative; visit www.zimmerbiomet.

com for additional product information. Check for country product clearances and reference product specific instructions for use. Zimmer

Biomet does not practice medicine. This technique was developed in conjunction with health care professional. This document is intended for surgeons and is not intended for laypersons. Each surgeon should exercise his or her own independent judgment in the diagnosis and treatment of an individual patient, and this information does not purport to replace the comprehensive training surgeons have received. As with all surgical procedures, the technique used in each case will depend on the surgeon’s medical judgment as the best treatment for each patient.

Results will vary based on health, weight, activity and other variables. Not all patients are candidates for this product and/or procedure. Caution:

Federal (USA) law restricts this device to sale by or on the order of a surgeon. Rx only.

©2015, 2021 Zimmer Biomet

Legal Manufacturer

Biomet Trauma

P.O. Box 587

56 East Bell Drive

Warsaw, Indiana 46581-0587

USA www.zimmerbiomet.com

2797

CE mark on a surgical technique is not valid unless there is a CE mark on the product label.

0007.2-GLBL-en-Issue Date 2021-12-16