Product Data Sheet and Manual TS8015 HP471055U015

Bulletin HP471055U015

Issue 1.0

Drawing No. LP0878X

Effective 10/11

MODEL TS8015 – GRAPHIC COLOR LCD OPERATOR INTERFACE TERMINAL

WITH TFT XGA DISPLAY AND TOUCHSCREEN



CONFIGURED USING DSI8000 SOFTWARE



UP TO 6 RS-232/422/485 COMMUNICATIONS PORTS

(2 RS-232 AND 2 RS-422/485 ON BOARD, 1 RS-232 AND 1

RS422/485 ON OPTIONAL COMMUNICATIONS CARD)



10 BASE T/100 BASE-TX ETHERNET PORT SUPPORTS MULTIPLE

PROTOCOLS SIMULTANEOUSLY



BUILT-IN WEB SERVER AND FTP SERVER/CLIENT



USB DEVICE PORT TO DOWNLOAD THE UNIT’S CONFIGURATION

FROM A PC OR FOR DATA TRANSFERS TO A PC



UNIT’S CONFIGURATION IS STORED IN NON-VOLATILE MEMORY

(64 MBYTE FLASH)



COMPACTFLASH ® SOCKET FOR DATABASE/RECIPE STORAGE

AND DATA LOGGING



15-INCH TFT ACTIVE MATRIX 32K COLOR XGA 1024 X 768 PIXEL

LCD



10-BUTTON KEYPAD FOR ON-SCREEN MENUS



THREE FRONT PANEL LED INDICATORS



POWERED BY 24 VDC ±20% SUPPLY



RESISTIVE ANALOG TOUCHSCREEN

GENERAL DESCRIPTION

The TS8015 Operator Interface combines powerful features normally found only in PC-based HMIs, with the reliability of a dedicated operating system. It is built around a high performance core with integrated features, allowing it to provide SCADA-like functionality at a fraction of the cost.

The TS8015 is able to act as a multiple protocol converter using four highspeed RS232/422/485 communications ports and an Ethernet 10/100 Base-TX port. The Ethernet port supports up to four protocols simultaneously, allowing dissimilar Ethernet based products to communicate with one another.

The TS8015’s USB port allows fast downloads of configuration files and access to trending and data logging. A CompactFlash socket is provided so that standard ComplactFlash cards can be used to collect your trending and data logging information as well as to store configuration files. The built-in web server allows processes to be controlled remotely.

The TS8015’s large, high-resolution display allows users to easily view and enter information. Data can be manipulated through the touchscreen and/or the

10-button keypad.

SAFETY SUMMARY

All safety related regulations, local codes and instructions that appear in the manual or on equipment must be observed to ensure personal safety and to prevent damage to either the instrument or equipment connected to it. If equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.

Do not use the controller to directly command motors, valves, or other actuators not equipped with safeguards. To do so can be potentially harmful to persons or equipment in the event of a fault to the controller.

CONTENTS OF PACKAGE

- TS8015 Operator Interface.

- Panel gasket.

- Template for panel cutout.

- Hardware packet for mounting unit into panel.

- Terminal block for connecting power.

ORDERING INFORMATION

DESCRIPTION

15" TFT XGA Display Operator Interface (indoor), USB Host

CANopen Option Card

Profibus DP Option Card

DeviceNet Option Card

FireWire Option Card

PART NUMBER

TS8015/00/00

8000/CB/00/00

8000/PB/00/00

8000/DN/00/00

8000/FA/00/00

The protective conductor terminal is bonded to conductive parts of the equipment for safety purposes and must be connected to an external protective earthing system.

WARNING - EXPLOSION HAZARD - SUBSTITUTION OF

COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I,

DIVISION 2

CAUTION: Risk Of Danger.

Read complete instructions prior to installation and operation of the unit.

CAUTION: Risk of electric shock.

CompactFlash is a registered trademark of CompactFlash Association.

1

S

pecificationS

1. POWER REQUIREMENTS:

Must use NEC Class 2 or Limited Power Source (LPS) rated power supply.

Power connection via removable three position terminal block.

Supply Voltage:

Typical Power 1 :

Maximum Power

+24 VDC ±20%

38 W

2 : 46 W

Notes:

1. Typical power with +24 VDC, RS232/485 communications, Ethernet communications, CompactFlash card installed, flash drive installed in one

USB Host port, and display at full brightness.

2. Maximum power is consumed when all features and comm ports are used at the same time. Refer to “Power Supply Requirements” under

“Installing and Powering the TS8015.”

3. The TS8015’s circuit common is not connected to the enclosure of the unit. See “Connecting to Earth Ground” in the section “Installing and

Powering the TS8015.”

4. Read “Power Supply Requirements” in the section “Installing and

Powering the TS8015” for additional power supply information.

2. BATTERY: Lithium coin cell. Typical lifetime of 10 years.

3. LCD DISPLAY:

SIZE

TYPE

COLORS

PIXELS

BRIGHTNESS

BACKLIGHT*

15-inch

TFT

32K

1024 X 768

600 cd/m 2

50,000 HR TYP.

*Lifetime at room temperature. Refer to “Display” in “Software/Unit Operation”

4. 10-KEY KEYPAD: for on-screen menus.

5. TOUCHSCREEN: Resistive analog

6. MEMORY:

On Board User Memory: 64 Mbyte of non-volatile Flash memory.

Memory Card: CompactFlash Type II slot for Type I and Type II

CompactFlash cards.

7. COMMUNICATIONS:

USB Device Port: Adheres to USB 2.0 Specification supporting high speed and full speed via Type B connection.

WARNING - DO NOT CONNECT OR DISCONNECT CABLES WHILE

POWER IS APPLIED UNLESS AREA IS KNOWN TO BE NON-

HAZARDOUS. USB PORT IS FOR SYSTEM SET-UP AND DIAGNOSTICS

AND IS NOT INTENDED FOR PERMANENT CONNECTION.

USB Host Ports: Comply with Universal Serial Bus Specification Rev 2.0.

Support data transfers at full-speed. Hardware over current protected (0.5

A max per port).

Serial Ports: Format and Baud Rates for each port are individually software programmable up to 115,200 baud.

PGM Port: RS232 port via RJ12.

COMMS Ports: RS422/485 port via RJ45, and RS232 port via RJ12.

DH485 TXEN: Transmit enable; open collector, V

V

OL

OH

= 15 VDC,

= 0.5 V @ 25 mA max.

Note: For additional information on the communications or signal common and connections to earth ground please see the “Connecting to

Earth Ground” in the section “Installing and Powering the TS8015.”

Port to port isolation: 500 Vrms for 1 minutes signal isolation : 50V

Ethernet Port: 10 BASE-T / 100 BASE-TX

RJ45 jack is wired as a NIC (Network Interface Card).

Isolation from Ethernet network to TS operator interface: 1500 Vrms

DIMENSIONS In inches (mm)

16.00 (406.4)

.28

(7.1)

2.8

(71.5)

8. ENVIRONMENTAL CONDITIONS:

Operating Temperature Range: 0 to 50 °C

Storage Temperature Range: -20 to 70 °C

Operating and Storage Humidity: 80% maximum relative humidity (noncondensing) from 0 to 50°C.

Vibration according to IEC 68-2-6: Operational 5 to 150 Hz, in X, Y, Z direction for 1.5 hours, 2 g.

Shock according to IEC 68-2-27: Operational 35 g, 9 msec in 3 directions.

Altitude: Up to 2000 meters.

9. CERTIFICATIONS AND COMPLIANCES:

SAFETY

IEC 61010-1, EN 61010-1: Safety requirements for electrical equipment for measurement, control, and laboratory use, Part 1.

IP66 Enclosure rating (Face only), IEC 529

Type 4X Enclosure rating (Face only), UL50

ELECTROMAGNETIC COMPATIBILITY

Emissions and Immunity to EN 61326: 2006: Electrical Equipment for

Measurement, Control and Laboratory use.

Immunity to Industrial Locations:

Electrostatic discharge EN 61000-4-2 Criterion A

4 kV contact discharge

8 kV air discharge

Electromagnetic RF fields EN 61000-4-3 Criterion A

Fast transients (burst)

Surge

10 V/m (80 MHz to 1 GHz)

3 V/m (1.4 GHz to 2 GHz)

1 V/m (2 GHz to 2.7 GHz)

EN 61000-4-4 Criterion A power 2 kV

I/O signal 1 kV

EN 61000-4-5 Criterion B power 1 kV L to L, 2 kV L to G signal 1 kV

RF conducted interference EN 61000-4-6 Criterion A

3 Vrms

Power freq. magnetic field EN 61000-4-8 Criterion A

AC power

Voltage dip

30 A/m

EN 61000-4-11 N/A

0% during 1 cycle

40% during 10/12 cycle

70% during 25/30 cycle

0% during 250/300 cycles Short interruptions

Emissions:

Emissions

Note:

EN 55011 Class A

1. Criterion A: Normal operation within specified limits.

2. Criterion B: Temporary loss of performance from which the unit self recovers.

10. CONNECTIONS: Compression cage-clamp terminal block.

Wire Gage: 12-22 AWG copper wire

Torque: 5-7 inch-pounds (56-79 N-cm)

11. CONSTRUCTION: Steel rear metal enclosure with NEMA 4X/IP66 aluminum front plate for indoor use only when correctly fitted with the gasket provided. Installation Category II, Pollution Degree 2.

12. MOUNTING REQUIREMENTS: Maximum panel thickness is 0.25" (6.3 mm). For NEMA 4X/IP66 sealing, a steel panel with a minimum thickness of

0.125" (3.17 mm) is recommended.

Maximum Mounting Stud Torque: 17 inch-pounds (1.92 N-m)

13. WEIGHT: 11.41 lbs (5.17 Kg)

14.59 (370.6)

13.00

(330.2)

F8

F9

11.59

(294.4)

PROTECTIVE EARTH GROUND

2

i

nStalling and

p

owering the

tS8015

MOUNTING INSTRUCTIONS

This operator interface is designed for through-panel mounting. A panel cutout diagram and a template are provided. Care should be taken to remove any loose material from the mounting cut-out to prevent that material from falling into the operator interface during installation. A gasket is provided to enable sealing to NEMA 4X/IP66 specification. Install the 22 kep nuts provided and tighten evenly for uniform gasket compression.

Note: Tightening the kep nuts beyond a maximum of 17 inch-pounds (1.92

N-m) may cause damage to the front panel.

15.425 (391.8)

10.283 (261.2)

5.142 (130.6) 22X ∅.188

(∅4.8)

CONNECTING TO EARTH GROUND

The protective conductor terminal is bonded to conductive parts of the equipment for safety purposes and must be connected to an external protective earthing system.

Each TS8015 has a chassis ground terminal on the back of the unit. Your unit should be connected to earth ground (protective earth).

The chassis ground is not connected to signal common of the unit.

Maintaining isolation between earth ground and signal common is not required to operate your unit. But, other equipment connected to this unit may require isolation between signal common and earth ground. To maintain isolation between signal common and earth ground care must be taken when connections

are made to the unit. For example, a power supply with isolation between its signal common and earth ground must be used. Also, plugging in a USB cable may connect signal common and earth ground.

1

1 USB’s shield may be connected to earth ground at the host. USB’s shield in turn may also be connected to signal common.

11.720

(297.7)

14.720 (373.9)

All tolerances ±0.010" (±0.25 mm).

2.485

(63.1)

7.455

(189.4)

12.425

(315.6)

ALL NONINCENDIVE CIRCUITS MUST BE WIRED USING

DIVISION 2 WIRING METHODS AS SPECIFIED IN THE NATIONAL

ELECTRICAL CODE, NFPA 70 FOR INSTALLATION WITHIN THE

UNITED STATES, OR AS SPECIFIED IN THE CANADIAN

ELECTRICAL CODE FOR INSTALLATION IN CANADA.

BLOCK DIAGRAM

POWER SUPPLY REQUIREMENTS

The TS8015 requires a 24 VDC power supply. Your unit may draw considerably less than the maximum rated power depending upon the options being used. As additional features are used your unit will draw increasing amounts of power. Items that could cause increases in current are additional communications, optional communications card, CompactFlash card, and other features programmed through DSI8000.

In any case, it is very important that the power supply is mounted correctly if the unit is to operate reliably. Please take care to observe the following points:

– The power supply must be mounted close to the unit, with usually not more than 6 feet (1.8 m) of cable between the supply and the operator interface. Ideally, the shortest length possible should be used.

– The wire used to connect the operator interface’s power supply should be at least 22-gage wire. If a longer cable run is used, a heavier gage wire should be used. The routing of the cable should be kept away from large contactors, inverters, and other devices which may generate significant electrical noise.

– A power supply with an NEC Class 2 or Limited Power Source (LPS) and SELV rating is to be used. This type of power supply provides isolation to accessible circuits from hazardous voltage levels generated by a mains power supply due to single faults. SELV is an acronym for

“safety extra-low voltage.” Safety extra-low voltage circuits shall exhibit voltages safe to touch both under normal operating conditions and after a single fault, such as a breakdown of a layer of basic insulation or after the failure of a single component has occurred.

24VDC

+

-

POWER

SUPPLY

A disconnect device must be provided by the end-user.

A

USB DEVICE

PROGRAMMING

A

ISOLATED

RS485

PORT A

ISOLATED

RS232

PORT A

PGM PORT

HOST A

B C A

WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT

EQUIPMENT WHILE THE CIRCUIT IS LIVE OR UNLESS THE AREA

IS KNOWN TO BE FREE OF IGNITABLE CONCENTRATIONS.

ISOLATED

RS485

PORT B

ISOLATED

RS232

PORT B

HOST B

D E A

ISOLATED

ETHERNET

ISOLATED

AUXILIARY

ETHERNET

G F

3

i

nStalling

a

n

o

ption

c

ard

WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT

EQUIPMENT UNLESS POWER HAS BEEN DISCONNECTED

AND THE AREA IS KNOWN TO BE NON-HAZARDOUS.

Each option card comes with a cable for communications and three screws for attaching the option card to the TS’s main board.

To install the option card, remove all power and I/O communications cables from the unit and remove the rear cover.

Connect the cable from the option card to the connector on the main board. Be sure both ends of the cable are firmly seated into their appropriate connector housings. Use the three screws provided to mount the option card to the main board as shown in

Figure 1.

Carefully replace the rear cover by reversing the instructions for removing the rear cover.

TYPICAL EXPANSION CARD INSTALLATION

Figure 1

c

ommunicating

w

ith the

tS8015

CONFIGURING A TS8015

The TS8015 is configured using DSI8000 software. DSI8000 is available as a free download from Parker - SSD Drives’ website. Updates to DSI8000 for new features and drivers are posted on the website as they become available. By configuring the TS8015 using the latest version of DSI8000, you are assured that your unit has the most up to date feature set. DSI8000 software can configure the

TS8015 through the RS232 PGM port, USB port, Ethernet port, or CompactFlash.

The USB port is connected using a standard USB cable with a Type B connector. The driver needed to use the USB port will be installed with DSI8000.

The RS232 PGM port uses a programming cable made by Parker - SSD Drives to connect to the DB9 COM port of your computer. If you choose to make your own cable, use the “TS8015 Port Pin Out Diagram” for wiring information.

The CompactFlash can be used to program a TS by placing a configuration file and firmware on the CompactFlash card. The card is then inserted into the target

TS, and the TS is then powered up. Refer to the DSI8000 literature for more information on the proper names and locations of the files.

USB, DATA TRANSFERS FROM THE

COMPACTFLASH CARD

ETHERNET COMMUNICATIONS

Ethernet communications can be established at either 10 BASE-T or 100

BASE-TX. The TS8015 unit’s RJ45 jack is wired as a NIC (Network Interface

Card). For example, when wiring to a hub or switch use a straight-through cable, but when connecting to another NIC use a crossover cable.

The Ethernet connector contains two LEDs. A yellow LED in the upper right, and a bi-color green/amber LED in the upper left. The LEDs represent the following statuses:

LED COLOR

YELLOW solid

YELLOW flashing

GREEN

AMBER

DESCRIPTION

Link established.

Data being transferred.

10 BASE-T Communications

100 BASE-TX Communications

On the rear of each unit is a unique 12-digit MAC address and a block for marking the unit with an IP address. Refer to the DSI8000 manual for additional information on Ethernet communications.

WARNING - DO NOT CONNECT OR DISCONNECT CABLES

WHILE POWER IS APPLIED UNLESS AREA IS KNOWN TO BE

NON-HAZARDOUS. USB PORT IS FOR SYSTEM SET-UP AND

DIAGNOSTICS AND IS NOT INTENDED FOR PERMANENT

CONNECTION.

In order to transfer data from the CompactFlash card via the USB port, a driver must be installed on your computer. This driver is installed with DSI8000 and is located in the folder C:\Program Files\Parker\DSI8000\Device\ after DSI8000 is installed. This may have already been accomplished if your TS8015 was configured using the USB port.

Once the driver is installed, connect the TS8015 to your PC with a USB cable, and follow “Mounting the CompactFlash” instructions in the DSI8000 user manual.

4

w

iring the

tS8015

TS8015 PORT PIN OUTS

PROTECTIVE EARTH GROUND

TxEN RxB Tx COMM COMM

ETHERNET

(NIC)

AUXILIARY

ETHERNET

(NIC)

PORT B

PORT A

USB

HOST

USB

TYPE B

POWER

CONNECTOR

RS485

PORT B

RS232

PORT B

RS485

PORT A

RS232

PORT A

PGM PORT

RS232 PORTS

The TS8015 has two isolated RS232 ports. The port marked “RS232/PORT

A/PGM PORT” may be used for programming as well as communications, while the port marked RS232/PORT B may only be used for communications.

Both ports can be used for either master or slave protocols.

RS232 CONNECTIONS

6 RTS

5 Tx

4 GND

3 GND

2 Rx

RS422/485 COMMS PORT

The TS8015 has two isolated RS422/485 ports. These ports can be configured to act as either RS422 or RS485.

RS422/485 4-WIRE

CONNECTIONS

5V

130K 7

1

TxB

TX

130K

8

2

TxA

RS485 2-WIRE

CONNECTIONS

5V

TX/RX

130K

130K

7

1

TxB

8

2

TxA

5 TxEN (OC) 5 TxEN (OC)

6 GND

RX

5V

130K

130K

4 RxB

3 RxA

6 GND

1 CTS

Note: All Parker - SSD Drives devices connect A to A and B to B.

5

Examples of RS485 2-Wire Connections

TS to Parker - SSD Drives RJ11

TS: RJ45

5

6

1

2

Name

TxEN

COM

TxB

TxA

Connections

SSD: RJ11

2

3

5

4

Name

TxEN

COM

B-

A+

DH485 Connections

The TS8015’s RS422/485 COMMS port can also be used for Allen Bradley

DH485 communications.

WARNING: DO NOT use a standard DH485 cable to connect this port to Allen

Bradley equipment. A cable and wiring diagram are available from Parker -

SSD Drives.

RJ45: SSD

1

2

3, 8

4, 7

5

6

4, 7

3, 8

TS to AB SLC 500

TxA

RxA

RxB

TxEN

COMM

TxB

TxA

Name

TxB

Connections

RJ45: A-B

1

-

2

-

5

-

-

4

Name

A

B

24V

COMM

TxEN

SHIELD

COMM

24V

S

oftware

/u

nit

o

peration

DSI8000 SOFTWARE

DSI8000 software is available as a free download from Parker - SSD Drives’ website. The latest version of the software is always available from the website, and updating your copy is free.

DISPLAY

This operator interface uses a liquid crystal display (LCD) for displaying text and graphics. The display utilizes a cold cathode fluorescent tube (CCFL) for lighting the display. The CCFL tubes can be dimmed for low light conditions.

These CCFL tubes have a limited lifetime. Backlight lifetime is based upon the amount of time the display is turned on at full intensity. Turning the backlight off when the display is not in use can extend the lifetime of your backlight. This can be accomplished through the DSI8000 software when configuring your unit.

KEYPAD

The TS8015 keypad consists of ten keys that can be used for on-screen menus.

TOUCHSCREEN

This operator interface utilizes a resistive analog touchscreen for user input.

The unit will only produce an audible tone (beep) when a touch on an active touchscreen cell is sensed. The touchscreen is fully functional as soon as the operator interface is initialized, and can be operated with gloved hands.

TROUBLESHOOTING YOUR TS8015

If for any reason you have trouble operating, connecting, or simply have questions concerning your new TS8015, contact Parker - SSD Drives’ technical support. For contact information, refer to the back page of this bulletin for phone and fax numbers.

EMAIL: [email protected]

Web Site: http://www.ssddrives.com/usa

FRONT PANEL LEDS

There are three front panel LEDs. Shown below is the default status of the LEDs.

LED INDICATION

GREEN (TOP, LABELED “PWR”)

FLASHING Unit is in the boot loader, no valid configuration is loaded.

1

STEADY Unit is powered and running an application.

YELLOW (MIDDLE)

OFF No CompactFlash card is present.

STEADY Valid CompactFlash card present.

FLASHING

RAPIDLY

CompactFlash card being checked.

FLICKERING

Unit is writing to the CompactFlash, either because it is

storing data, or because the PC connected via the USB port

has locked the drive.

2

FLASHING

SLOWLY Incorrectly formatted CompactFlash card present.

GREEN (BOTTOM)

FLASHING A tag is in an alarm state.

STEADY Valid configuration is loaded and there are no alarms present.

1. The operator interface is shipped without a configuration. After downloading a configuration, if the light remains in the flashing state continuously, try cycling power. If the LED still continues to flash, try downloading a configuration again.

2. Do not turn off power to the unit while this light is flickering. The unit writes data in two minute intervals. Later Microsoft operating systems will not lock the drive unless they need to write data; Windows 98 may lock the drive any time it is mounted, thereby interfering with logging. Refer to

“Mounting the CompactFlash” in the DSI8000 User Manual.

6

BATTERY & TIME KEEPING

WARNING - EXPLOSION HAZARD - THE AREA MUST BE

KNOWN TO BE NON-HAZARDOUS BEFORE SERVICING/

REPLACING THE UNIT AND BEFORE INSTALLING OR

REMOVING I/O WIRING AND BATTERY.

WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT

EQUIPMENT UNLESS POWER HAS BEEN DISCONNECTED

AND THE AREA IS KNOWN TO BE NON-HAZARDOUS.

CAUTION: The circuit board contains static sensitive components.

Before handling the operator interface without the rear cover attached, discharge static charges from your body by touching a grounded bare metal object. Ideally, handle the operator interface at a static controlled clean workstation. Also, do not touch the surface areas of the circuit board. Dirt, oil, or other contaminants may adversely affect circuit operation.

A battery is used to keep time when the unit is without power. Typical accuracy of the TS8015 time keeping is less than one minute per month drift.

The battery of a TS8015 unit does not affect the unit’s memory, all configurations and data is stored in non-volatile memory.

To change the battery of a TS8015, remove power, cabling, and then the rear cover of the unit. To remove the cover, remove the 16 screws on the rear of the unit. Then, by lifting the top side, hinge the cover, thus providing clearance for the connectors on the bottom side of the PCB as shown in the illustration below. Install in the reverse manner.

Remove the old battery* from the holder and replace with the new battery.

Replace the rear cover, cables, and re-apply power. Using DSI8000 or the unit’s keypad, enter the correct time and date.

* Please note that the old battery must be disposed of in a manner that complies with your local waste regulations. Also, the battery must not be disposed of in fire, or in a manner whereby it may be damaged and its contents come into contact with human skin.

The battery used by the TS8015 is a lithium type CR2025.

WARNING - EXPLOSION HAZARD -

BATTERIES MUST ONLY BE CHANGED IN AN

AREA KNOWN TO BE NON-HAZARDOUS.

CAUTION: RISK OF ELECTRIC SHOCK

The inverter board, attached to the mounting plate, supplies the high voltage to operate the backlight. Touching the inverter board may result in injury to personnel.

COVER PLATE

(FUTURE)

BATTERY

EXPANSION

CARD

INVERTER o

ptional

f

eatureS and

a

cceSSorieS

COMPACTFLASH SOCKET

CompactFlash socket is a Type II socket that can accept either Type I or II cards. Use cards with a minimum of 4Mbytes with the TS8015’s CompactFlash socket. Cards are available at most computer and office supply retailers.

CompactFlash can be used for configuration transfers, larger configurations, data logging, and trending.

Information stored on a CompactFlash card by a TS8015 can be read by a card reader attached to a PC. This information is stored in IBM (Windows compatible FAT16 file format.

® ) PC

OPTIONAL COMMUNICATION CARD

Parker - SSD Drives offers optional communication cards for fieldbus communications. These communication cards will allow your TS8015 to communicate with many of the popular fieldbus protocols.

Parker - SSD Drives is also offering a communications card for additional

RS232 and RS422/485 communications.

NOTE

For reliable operation of this and other Parker - SSD Drives products, one of the following brands of CompactFlash card must be used...

SimpleTech

SanDisk ®

SMART ® Modular

Silicon Systems

Note: Do not remove or insert the CompactFlash card while power is applied. Refer to

“Front Panel LEDs.”

CompactFlash-

Insert Face Up

)

7

Parker Hannifin Corporation

SSD Drives Division

9225 Forsyth Park Dr.

Charlotte, NC 28273 USA

Tel: (704) 588-3246

Fax: (704) 588-4806 www.ssddrives.com/usa [email protected]