CHIPPER ASSEMBLY GUIDE
MODEL: OPC503V
3 IN CHIPPER SHREDDER
DETAIL K2 INC.
DK2 POWER USA
4301 S Valley View Blvd STE 10-11
Las Vegas, NV 89103
1-702-331-5353
DETAIL K2, INC.
1080 Clay Avenue Unit 2
Burlington, Ontario, Canada L7L0A1
DK2 USA EAST
6245 Industrial Parkway
Whitehouse, OH 43571
PARTS AND SERVICE 702-331-5353 OR WWW.DK2POWER.COM
CONTACT US
LEAF VAC CHIPPER SHREDDER
LEAF VAC
3 IN CHIPPER
SHREDDER
OPC503V 3 INCH LEAF VAC
CHIPPER SHREDDER
REV 1 – 9-19-2019
STEP 1:
Open and unpack all items. Leave lots of working space.
Inspect all parts.
The CHIPPER is shipped in a crate. Remove all sides before you begin.
NOTE: UPON INSPECTION OF PARTS IF YOU FIND ANY DAMAGE OR MISSING
PARTS PLEASE CALL DK2 POWER AT 702-331-5353 OR CONTACT US VIA
OUR WEBSITE WWW.DK2POWER.COM
WE WILL REPLACE ANY MISSING PARTS TO YOU FREE
PLEASE DO NOT RETURN TO THE STORE
REV 1 – 9-19-2019
STEP 2:
1. INSTALL THE HANDLE
2. Use 4 bolts and hardware provided
Install hardware and tighten
REV 1 – 9-19-2019
STEP 3:
1. INSTALL THE CHIP CHUTE
2. Install using the 5 bolts and hardware included
5 BOLTS AND WASHERS
REV 1 – 9-19-2019
STEP 4:
1. INSTALL THE TREE FEED CHUTE
2. Remove the 4 nuts and hardware
3. Be cautious NOT TO DROP them into the cutting chamber.
4. Install chute and tighten
4 NUTS AND WASHERS
REV 1 – 9-19-2019
STEP 5:
1. INSTALL THE LEAF VAC HOSE
2. Remove the 3 nuts and hardware and the cover plate.
3. Keep the plate in case you will remove the hose in the future.
4. Install the hose plate and shown, replace the nuts and tighten.
REV 1 – 9-19-2019
STEP 6
1. LEAF VAC HOSE STORAGE
2. Wrap the hose OVER the chip chute as shown
3. Wrap the hose across the front of the hopper
4. Place the HOSE HANDLE across the push bar as shown and
UNDER THE HOSE.
5. Let engine cool before you wrap your hose into storage position. Take care NOT to melt it on the muffler.
1 st wrap over the chute
2 nd around the front
3 rd handle UNDER the hose
REV 1 – 9-19-2019
STEP 7
1. INSTALL THE TOW BAR TROLLEY COMBO
2. Remove the pin, insert the tow bar with wheel down, re-pin.
Install tow bar
Wheel in down position to trolley mode
REV 1 – 9-19-2019
STEP 8
1. TOW BAR TROLLEY COMBO
2. Shown is trolley mode
3. Remove Tow Bar and flip over for TOWING position.
4. When tow bar is removed, to increase your work area when chipping, use the drop stand.
Wheel down for easy transport
Flip bar over for towing Drop stand when tow bar is removed to increase work area
REV 1 – 9-19-2019
STEP 9
1. DROP STAND
2. Drop stand is up when trolley wheel is down.
3. Drop stand is up when tow bar is reversed for towing.
REV 1 – 9-19-2019
STEP 10
1. WHEEL LOCK FEATURE
2. REMEMBER TO RAISE YOUR DROP STAND AND TO UNLOCK
YOUR WHEELS BEFORE TOWING
3. Wheel shown is in free wheeling position
4. Remove pin, slide wheel forward, re-pin wheel and axel together to keep wheel from rolling and LOCK.
5. BOTH WHEELS LOCK TO HOLD YOUR CHIPPER IN PLACE
FROM ROLLING WHEN YOU ARE WORKING.
REV 1 – 9-19-2019
STEP 11
1. ENGINE
2. Change oil after first 5 hours of use on brand new engine
3. Fill oil full, your engine has a low oil shutoff and will not start if low on oil. This is a protection system for your engine.
4. See Engine manual for complete instructions.
5. TURN KEY ON
6. CHOKE IF NEEDED
7. TURN ON GAS- SLIDE LEVER ALL THE WAY TO THE RIGHT
8. PULL AND START
REV 1 – 9-19-2019
STEP 12
1. SAFETY KIT AND TOOLS
2. The white bottle is used for oil fill
3. Work gloves, safety glasses, ear protection included.
4. A 1 7/8 tow ball is included
5. Manuals and assembly tools.
6. Storage tool bag
REV 1 – 9-19-2019
REV 1 – 9-19-2019
Specification
M10*70 bolt hitch trailer washer ⌀ 10.5* ⌀ 22*2 spring washer ⌀ 10
M10locknut
M8*45 bolt washer ⌀ 8.4* ⌀ 20*1.6
Rubber pad support feet
M8locknut spring washer ⌀ 8 tow bar latch ⌀ 8 engine plate
M8*60 bolt
Rubber pad ⌀ 10
M8*85 bolt
U-protection plate engine wire engine protection pipe main chipper room cover
5/16-24UNF*85 bolt
M8*25bolt blade key blade roller
M8*20 bolt washer ⌀ 30* ⌀ 13*4 straight hammer
L-hammer
Straight sleeve
M8*50bolt gland
5/16-24UNF*135 bolt main chipper room
O-latch ⌀ 8 tire axle
M8*16 bolt
30
31
32
33
25
26
27
28
29
21
22
23
24
17
18
19
20
38
39
40
34
35
36
37
12
13
14
15
16
10
11
8
9
6
7
4
5
No.
1
2
3
Specification3
M6locknut spring washer ⌀ 6 washer ⌀ 6.4* ⌀ 12*1.6
side chipper room side chipper room cover
M6*12 bolt
M8*20 bolt
M8*25 bolt rubber pad swtich key wire top feed hopper swtich stop cover
M6*16 bolt switch key handle plate for protection sheet protection sheet
M6*20 bolt outlet hopper adjusting plate knob outlet hopper
M6*35 bolt side plate for protection sheet side protection sheet side feed hopper trolley wheel
M10*50 bolt
M10locknut spring washer ⌀ 10
Hose Clamp hose hose cover hose handle
M6*50 bolt
70
71
72
73
65
66
67
68
69
74
61
62
63
64
57
58
59
60
52
53
54
55
56
48
49
50
51
44
45
46
47
No.2
41
42
43
REV 1 – 9-19-2019
READ THE KOHLER ENGINE MANUAL SUPPLIED WITH YOUR
UNIT FOR FULL ENGINE OPERATION, SAFETY, AND
MAINTENANCE.
YOUR UNIT HAS A COMMERCIAL KOHLER ENGINE WITH A 3YR
PARTS AND SERVICE WARRANTY. FOR WARRANTY IN YOUR
AREA CONTACT THE NEAREST KOHLER DEALER.
VISIT WWW.KOHLERENGINES.COM
FOR PARTS, SERVICE,
MANUALS, AND DEALER LOCATIONS.
REV 1 – 9-19-2019
OPERATION – BEFORE TURNING KEY AND PULL STARTING ENGINE
CLEAR AREA OF ALL PEOPLE AND PROPERTY THAT COULD BE DAMAGED. THINK
SAFETY. CHIPS ARE FLYING PROJECTILES AND CAN CAUSE INJURY.
WEAR SAFETY GLASSES, HEARING PROTECTION, AND GLOVES
DO NOT WEAR LOOSE FITTING CLOTHES THAT COULD GET STUCK IN THE MACHINE
MOVING PARTS, ONLY CHIP WOOD, CHILDREN SHOULD NOT RUN THIS EQUIPMENT,
STAY ALERT OF YOUR SURROUNDING AND PERSONS THAT COULD APEAR IN THE
CHIP PATH WHILE YOU ARE WORKING.
UNIT IS DIRECT DRIVE. NO CLUTCH
TO SLIP OR BURN UP.
Before starting make sure all chutes are clear of branches as the cutting wheel will turn as you pull the recoil starter. Cutter wheel must be free to turn when starting.
PERFORMANCE OPERATION -
Feed larger trees upto 3 inches in diameter slowly into the tubular feed chute allowing the cutter wheel to regain speed. Shoving a tree into the cutter wheel will stall the machine and damage the cutters or drive shaft.
Feed small twigs, leaves, and small branches upto 3/8 inch dia into the top hopper.
Wear gloves, as the cutter will grab the branches and pull them into the machine and from your hands. NEVER PLACE HANDS INTO THE TOP FEEDER.
To clear the top feeder turn the key off, remove it, unplug the spark plug.
Be safe, the cutters on this machine are high speed and very sharp.
SET BOTH OF YOUR WHEEL BRAKE PINS to STABILIZE MACHINE DURING OPERATION.
READ AND OBEY ALL WARNING LABELS ON THIS MACHINE.
REV 1 – 9-19-2019
PLEASE DO NOT RETURN TO THE STORE
YOU HAVE A 1 YEAR WARRANTY AND DK2 WILL REPLACE A DEFECTIVE PART FOR FREE
CALL US AT
702-331-5353
FOR FAST WARRANTY PARTS AND QUESTIONS
WHAT IS COVERED
DK2 Inc. warrants to the original purchaser of any DK2 product that it will be free and clear of manufacturing defects in workmanship and materials under normal use and service for a period of one (1) year from the date of the original purchase.
If within one (1) year from the original date of purchase this product fails due to defect in material or workmanship. DK2 POWER outdoor power equipment is 1-year parts only warranty no labor.
Upon expiry of one (1) year, Detail K2 will have no further liability related to the product. Detail K2 does not authorize any party, including its authorized distributors or dealers, to offer any other warranty on behalf of
Detail K2 Inc.
KOHLER ENGINES – KOHLER CH SERIES ENGINES COMMERCIAL 3 YR PARTS AND LABOR WARRANTY see your Kohler manual for specific warranty.
DIESEL TRACTORS – Chassis component parts only, no labor, ENGINES – 1 YR KOHLER WARRANTY
DK2 POWER OUTDOOR EQUIPMENT – 1-Year parts only, no labor.
THIS WARRANTY DOES NOT COVER OR APPLY TO:
Damage to the product due to misuse, mishandling and abuse
(b) Improper installation, maintenance and storage
(c) Expendable parts such as nuts and bolts, pins and springs, wiring and switch components, hydraulic hoses and fittings, cutting teeth, cutting chains, cutting blades, throttles, belts and tires.
(d) Normal wear and tear
(e) Consequential damage & incidental damages such as damage to persons or property
PROCEDURE FOR OBTAINING AN RETURN AUTHORIZATION
Within the one (1) year warranty period, the purchaser of the product must notify DK2 of the claimed defect and provide proof of original purchase. At this time the validity of the claim will be determined, and if approved replacement parts will be issued.
No returned product will be accepted under warranty unless accompanied by an RGA# issued by Detail K2
Inc.
RESOLUTION FOR A DEFECTIVE PRODUCT
DK2 POWER – Tractors, Chippers, Stump Grinders, Log Splitters, and Outdoor Power Equipment.
Call DK2 at 702-331-5353 in Las Vegas between 8am-4pm M-F Pacific Time.
REV 1 – 9-19-2019
