Key Lever spigot
Mounting screws (3)
Two lengths provided
Cover screws (4)
Also includes (not shown): a) Strike plate & screws b) 4 x AA Alkaline batteries
Ø54mm
(2-1/8”)
Slide the spindle hole position to suit 60mm
(2-3/8”) or 70mm (2-3/4”) backset
Ø60mm
(2-3/8”)
Ø60mm
(2-3/8”)
Ø70mm
(2-3/4”)
Ø70mm
(2-3/4”)
1. Install latch on the door, ensuring the pin
side of the latch is facing away from the
door jamb/frame.
3. Position the inside mounting plate to sit
flush on the door, ensuring the cable and
spindle go through the holes in the mounting
plate. Secure both assemblies using 8/32
screws provided. Make sure the exterior
assembly is vertically aligned. If you added
the cross bolt, securely tighten the post to
the exterior Ease unit with the additional
screw provided.
Optional screw
Pin side of the latch
NOTE: Cable must go through door hole above the latch.
Ensure the spindle is square.
This hole is for the optional cross bolt provided for stabilising your lock.
If you drilled a hole, securely tighten the post before mounting on the door.
4. Attach cable assembly to the interior
assembly PCB by lining up notches on
top of cable connector to slots on PCB
connector. Press connector in firmly until
completely connected.
5. Install interior assembly on inside mounting
plate. Secure using 4 screws through the
interior assembly onto the mounting plate.
7. Insert the cylinder into the lever.
6. Install batteries and battery cover.
8. Using a flat head screwdriver, ensure the
turnplate is set vertical.
Turnplate
9. Insert the key into the cylinder and ensure
the key is horizontal. Check handing to
ensure the lever is pointing towards the
hinges. Push the lever onto the lever
spigot until it clicks into place.
11. Install strike into door jamb.
10. Install the internal lever ensuring the
handle points towards the door hinges.
Warnings
Do not install batteries until the lock is completely installed on the door.
Failure to follow these instructions could result in damage to the product and void the factory warranty.
The accuracy of the door preparation is critical for the functioning and security of this product.
Misalignment can cause performance degradation and lessening of security.
Finish Care: This lockset is designed to provide the highest standard of product quality and performance. Care should be taken to ensure a long-lasting finish. When cleaning is required, use a soft, damp cloth. Do not use lacquer thinner, caustic soaps, abrasive cleaners or polishes as these can damage the coating and result in tarnishing.
Definitions
Fake PIN code:
Random numbers that are added before or after the user PIN. This prevents the user PIN from being exposed.
Master mode:
The master mode could be entered by entering
[**Master PIN Code #] to program the lock.
Master PIN code:
The master PIN code is used for programming and for feature settings.
Passage mode:
The lock can be switched to passage mode by toggling the switch on the internal side. In this mode, it is unlocked inside/out and you may enter freely. You may still lock the unit externally by holding any key for 2 seconds. It will resume passage mode when unlocked via PIN or key override until the passage mode switch is shifted to the locked position. Note: Enabling and disabling passage mode can only be done on the internal side of the unit via the switch.
Hardware specifications
Item
External assembly
Specifications
165mm (L) x 70mm (W) x 22mm (D)
Internal assembly
Battery
196mm (L) x 73mm (W) x 28mm (D)
AA alkaline battery x 4
(Operation voltage: 4.6~6.0V)
Reset button:
After reset operation, the lock will be restored to factory default settings, all user credentials will be deleted. Refer to page 11 for instructions on how to reset your lock.
Shutdown time:
The lock will shutdown for a default of 3 minutes and not allow operation after the wrong code entry limit (5 times) has been met. When the unit is in shutdown, the light will flash if you are trying to use the keypad.
Silent mode:
Disables the tone sound.
Status indicators:
Located on exterior assembly.
User PIN code:
The user PIN code operates the lock. Maximum number of user PIN codes is 20.
Notes
Operation temperature:
-20ºC to 55ºC
Lasts up to one year
(10 times open/close per day)
Enter
* * Master PIN code #
* *
Enter
Master PIN code #
Enter
* * Master PIN code #
* *
Enter
Master PIN code #
* *
Enter
Master PIN code #
Notes:
1. Beeps sound only when sound is enabled.
2. If the indicators show 3 red lights and 3 beeps, your setting has failed. The system will exit master mode.
Please enter master mode to try again.
3. Refer to page 9 for guidelines on setting PIN codes.
Setting PIN codes
1. Master PIN Code (4~10 digit): Default
master PIN code is “12345678”, please
modify it after installation.
If you forget your master PIN code, you
can reset your lock back to factory settings
(refer to page 11 for instructions).
2. User PIN Code (4~10 digit): User PIN codes
can be set up through master PIN code.
Up to 20 user PIN codes can be stored.
3. Both master and user PIN codes don’t
support the following combination of numbers.
Normal mode
1. Enter the master
or user PIN code,
followed by #,
then rotate the
lever to open the
door. Door will
automatically
re-lock 7 seconds
later. If you wish
to deactivate the
7-second auto re-lock feature,
switch to passage mode (page 10).
2. Alternatively, use the backup key provided.
If unit is locked and you require emergency battery power, located on the bottom of the external unit is a micro USB port (refer to the exterior assembly diagram on page 3). Using a micro USB cable and charged power bank, you can power the lock to regain access as required.
If you need to reset your lock, the reset button is located under the left-most battery in the battery casing. Use a pointed object, press and hold the reset button for over 5 seconds until you hear a beep.
For an enhanced experience and additional functionality, try using the Schlage Ease ™ with the Schlage Abode mobile application.
Simply download the Schlage Abode app from the Apple App Store or the Google
Play Store. Manage and control your lock with the ease of your smartphone with greater control and access.
