GB
CHARACTERISTICS
Refrigerator model
Freezer model
-19 -22
Internal temp. Range
°C
-2 +10
Single phase pow er supply (50Hz)
V
230
230
Pow er input
W
500
600
Max. current input
A
2,6
3
Refrigeration output (1)
W
400 (1)
410 (2)
Max. ambient temperature
°C
+43
+43
Refrigerant
Grill/draw er dimensions
R
404A
404A
mm
Grills 325 x 530
Draw er 305x590*250
(1) With an ambient temperature of +43°C , a condensation temperature of +50°C and an evaporation temperature of -15°C.
(2) With an ambient temperature of +43°C, a condensation temperature of +50°C and an evaporation temperature of -35°C.
- an all-pole circuit-breaker with minimum contact gap of 3 mm
must be fitted between the socket and the power supply line.
• The appliance must also be included in a suitably dimensioned
equipotential system of proven efficiency.
GENERAL INSTRUCTIONS
1. Read the contents of this manual carefully as it contains
important safety information regarding the installation, use and
maintenance of the appliance.
Keep this manual in a safe place so it may be used in future by
other operators.
Note!
Because this appliance has a Y-type electric connection, the
power supply cable must only be replaced by a qualified electrician.
Equipotential node and earth connection
Connect the appliance to an earth; it must be included in an
equipotential node by means of the screw located under the
2. The installation of this appliance must be carried out by
qualified persons in accordance with the manufacturer’s
instructions.
frame. The screw is marked with the symbol:
3. Disconnect the appliance in the event of malfunction or
irregular operation. Have the appliance repaired by a service
centre authorized by the manufacturer and demand original
spare parts are used.
Failure to observe the above indications may compromise the
safety of the appliance.
The Manufacturer declines all liability for situations arising
from failure to comply with these safety regulations.
USER INSTRUCTIONS
Use
• This appliance must be used exclusively for the purpose for
which it has been designed, namely for the refrigeration or
preservation of food. Any other use is to be considered improper.
• To get the best use of the appliance, observe the following
indications:
- avoid placing hot foods or liquids in the appliance,
- make sure all foods are covered or wrapped,
- leave enough space between the grids and the sides of the
appliance in order to ensure correct air circulation,
- do not leave the doors open for long periods whilst placing items
in or removing items from the appliance.
Compliance with current Directives
This appliance is manufactured in compliance with the
requirements of Directives:
- CEE 89/336 electromagnetic compatibility
- CEE 73/23 low voltage
- CEE 98/37 machines
and relative reference standards.
• The appliance must also be included in an equipotential system
whose efficiency must be suitably verified.
INSTALLATION INSTRUCTIONS
REFRIGERATOR MODELS (fig.1)
Positioning
• The appliance must be installed in a well ventilated room, as far
as possible from heat sources and in such a way so as to ensure
good air circulation, especially around the compressor unit. The
room temperature should not exceed +43°C in order to maintain
the recommended internal temperatures.
• Use the height-adjustable feet to make sure the appliance is
level, and at the same time check that the door closes properly.
• For appliances with stainless steel cabinets, peel off the
protective film very slowly, without tearing it, to avoid leaving glue
stuck to the surface. Should this happen, remove the traces of
glue with kerosene or benzine.
Control panel
A - Digital Thermoregulator
B - On/Off switch
Switching on
• Switch on the safety switch upline of the appliance.
• Press button “B” on the control panel. The incorporated indicator
lamp lights up to indicate that the appliance is powered up.
• The thermostat is factory set to a working temperature of 0°C.
When the appliance is working, the Digital Thermoregulator “A”
indicates the internal cell temperature.
• When the set temperature has been reached, the thermostat
will disconnect the compressor unit and reconnect when necessary
so as to maintain an almost constant temperature.
ELECTRICAL CONNECTION
• The electrical connection must be carried out in conformity with
the current local safety regulations.
• To connect to the power supply, insert the power plug into the
corresponding mains socket, first making sure that:
- the voltage and frequency rated on the appliance data plate
conform to those of the mains supply;
- the mains socket has an adequate current carrying capacity
and is suitably earthed. If you have doubts about the efficiency of
the earth connection have the installation checked by a qualified
technician.
6
DEFROSTING
The appliance is equipped with an automatic defrost function. .
The defrost water is collected in a basin under the appliance.
CARE AND MAINTENANCE
Before carrying out any cleaning or maintenance operations,
disconnect the appliance from the mains power supply.
REFRIGERATOR MODELS (fig.1)
Cleaning the appliance internally
• Before using the appliance clean all internal parts and the
accessories with warm water and neutral soap then rinse and dry
thoroughly.
Do not use abrasive cleaning powders or detergents.
Freezer models
A - Thermometer and electronic control
B - On/Off switch
Switching on (fig.1)
• Switch on the safety switch upline of the appliance.
• Press button “B” on the control panel. The incorporated indicator
lamp lights up to indicate that the appliance is powered up.
• The thermostat is factory set to a working temperature of -22°C
to guarantee an average cell temperature of -20°C.
The working temperature can be changed:
set
to increase the temperature,
set
to lower the temperature.
Periodic cleaning
• Clean stainless steel parts using a cloth and warm water and
neutral soap, then rinse thoroughly and dry well. When cleaning
these surfaces never use detergents containing abrasive or
corrosive substances, common wire wool, wire brushes, scrapers
or other such implements.
• Painted parts should be cleaned using silicon wax.
• The condenser fins of the refrigeration unit must be cleaned at
least once every six months, using a brush or a vacuum cleaner
(fig.2).
• Avoid using sharp implements whilst cleaning the evaporator
and condenser.
• Empty the defrost basin, located under the appliance, every
day.
Attention: Do not wash the appliance with water jets.
When the appliance is working, the Digital Thermoregulator “A”
indicates the internal cell temperature.
• When the set temperature has been reached, the thermostat
will disconnect the compressor unit and reconnect when necessary
so as to maintain an almost constant temperature.
Prolonged disuse
If the appliance is not going to be used for a long period, take the
following precautions :
- remove the plug from the socket;
- remove all food from the cell and clean the interior and the
accessories;
- leave the doors open to allow the air to circulate inside, so
preventing the formation of unpleasant odours;
- briskly rub a cloth soaked in vaseline oil over all the stainless
steel surfaces so that it forms a protective film;
- air the premises regularly.
DEFROSTING
The appliance is equipped with an automatic defrost function.
7
">
