Nissan Primera 2000 Workshop Manual
Nissan Primera: Your versatile companion for seamless driving experiences. With its advanced technology, the Nissan Primera offers a range of features to enhance your journeys:
- Effortless Handling: Enjoy precise control and smooth maneuvering with the Primera's responsive steering and suspension system, designed for a comfortable and confident driving experience.
- Enhanced Safety: Experience peace of mind with the Primera's comprehensive safety features, including airbags, seatbelts, and advanced braking systems, ensuring your well-being on every trip.
விளம்பரம்
விளம்பரம்
BODY & TRIM
SECTION
BT
CONTENTS
PRECAUTIONS ......................................................... 2
Service Notice........................................................ 2
Supplemental Restraint System (SRS) ‘‘AIR
BAG’’ and ‘‘SEAT BELT PRE-TENSIONER’’ ........ 2
GENERAL SERVICING ............................................. 3
Clip and Fastener .................................................. 3
BODY END ................................................................ 5
Body Front End...................................................... 5
Body Rear End and Opener .................................. 7
DOOR ....................................................................... 13
Front Door............................................................ 13
Rear Door ............................................................ 14
INSTRUMENT PANEL ............................................. 15
INTERIOR TRIM ...................................................... 18
Side and Floor Trim ............................................. 18
Door Trim ............................................................. 24
Roof Trim ............................................................. 25
Trunk Room Trim................................................. 28
Luggage Room Trim ............................................ 62
Back Door Trim.................................................... 30
EXTERIOR ............................................................... 31
SEAT ........................................................................ 40
Front Seat ............................................................ 40
Heated Seat ......................................................... 42
Rear Seat............................................................. 43
SUNROOF ................................................................ 46
Trouble Diagnoses............................................... 49
WINDSHIELD AND WINDOWS .............................. 53
Windshield and Rear Window ............................. 54
Side Window ........................................................ 55
Back Door Window .............................................. 56
MIRROR ................................................................... 58
Door Mirror........................................................... 58
Rearview Mirror.................................................... 59
BODY ALIGNMENT ................................................. 60
Engine Compartment ........................................... 60
Underbody............................................................ 62
BT
PRECAUTIONS
●
●
●
●
●
Service Notice
When removing or installing various parts, place a cloth or padding onto the vehicle body to prevent scratches.
Handle trim, molding, instruments, grille, etc. carefully during removing or installing. Be careful not to soil or damage them.
Apply sealing compound where necessary when installing parts.
When applying sealing compound, be careful that the sealing compound does not protrude from parts.
When replacing any metal parts (for example body outer panel, members, etc.), be sure to take rust prevention measures.
Supplemental Restraint System (SRS) ‘‘AIR
BAG’’ and ‘‘SEAT BELT PRE-TENSIONER’’
The Supplemental Restraint System ‘‘Air Bag’’ and ‘‘Seat Belt Pre-tensioner’’, used along with a seat belt, helps to reduce the risk or severity of injury to the driver and front passenger in a frontal collision. The
Supplemental Restraint System consists of air bag modules (located in the center of the steering wheel and on the instrument panel on the passenger side), seat belt pre-tensioners, a diagnosis sensor unit, warning lamp, wiring harness and spiral cable. Information necessary to service the system safely is included in the
RS section of the Service Manual.
If the vehicle is equipped with side air bag as the Supplemental Restraint System, the side air bag used along with the seat belt helps to reduce the risk or severity of injury to the driver and front passenger in a side collision. The side air bag consists of air bag modules (located in the outer side of front seats), satellite sensor, diagnosis sensor unit (which is one of components of air bags for a frontal collision), wiring harness, warning lamp (which is one of components of air bags for a frontal collision).
WARNING:
● To avoid rendering the SRS inoperative (which could increase the risk of personal injury or death
● in the event of a collision which would result in air bag inflation) all maintenance must be performed by an authorized NISSAN dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system.
● Do not use electrical test equipment on any circuit related to the SRS unless instructed to do so in this Service Manual. SRS wiring harnesses are covered with yellow insulation (either just before the harness connectors or for the complete harness) for easy identification.
BT-2
GENERAL SERVICING
●
●
Clip and Fastener
Clips and fasteners in BT section correspond to the following numbers and symbols.
Replace any clips and/or fasteners which are damaged during removal or installation.
Symbol
No.
Shapes Removal & Installation
Removal:
Remove by bending up with flat-bladed screwdrivers or clip remover.
C101
SBF302H SBF367BA
C103
C203
C205
SBT095
Removal:
Remove with a clip remover.
SBF423H
Push
Push center pin to catching position.
(Do not remove center pin by hitting it.)
Push
SBF258G
Removal:
Installation:
Screwdriver
SBF708E
Finisher
Clip
MBT080A SBF638C
BT-3
Symbol
No.
CE117
CF118
CR103
GENERAL SERVICING
Clip and Fastener (Cont’d)
Shapes Removal & Installation
Removal:
Remove by bending up with a flat-bladed screwdriver or pliers.
Sealing washer
Clip-A
Clip-B
(Grommet)
SBF174D
Removal:
Flat-bladed screwdriver
Finisher
SBF175DA
Body panel
Clip-A
Clip-B
(Grommet)
Sealing washers
SBF151D SBF259G
Removal:
Holder portion of clip must be spread out to remove rod
SBF770B
SBF768B
Removal:
1. Screw out with a Phillips screwdriver.
2. Remove female portion with flat-bladed screw-driver.
CS101
SBF078B SBF992G
BT-4
BODY END
●
●
●
●
●
Body Front End
When removing or installing hood, place a cloth or other padding on the front fender panels and cowl top. This prevents vehicle body from being scratched.
Bumper fascia is made of plastic. Do not use excessive force and be sure to keep oil away from it.
Hood adjustment: Adjust at hinge portion.
Hood lock adjustment: After adjusting, check hood lock control operation. Apply a coat of grease to hood locks engaging mechanism.
Hood opener: Do not attempt to bend cable forcibly. Doing so increases effort required to unlock hood.
V
V
V
V
V
V
REMOVAL — Front bumper assembly
Remove clips
C205 securing bumper fascia to engine undercover.
Remove screws and clips
C205 securing left and right sides of front fender protector.
Remove screws securing radiator core support to bumper fascia.
Remove screws securing left and right front fenders to bumper fascia.
Remove clips
CS101 securing retainer to bumper fascia.
Extract bumper fascia assembly.
Remove screws securing fog lamps. Then remove fog lamps.
10.8 - 14.6 N·m
(1.1 - 1.5 kg-m,
8.0 - 10.8 ft-lb)
YBT001
BT-5
SEC. 261 c 620 c 623 c 650 c 656
Hood lock adjustment
● Adjust hood so that hood primary lock meshes at a position 1 to 1.5 mm (0.039 to
0.059 in) lower than fender.
●
●
After hood lock adjustment, adjust bumper rubber.
When securing hood lock, ensure it does not tilt. Striker must be positioned at the center of
● hood primary lock.
After adjustment, ensure that hood primary and secondary lock operate properly.
.
Hood lock secondary latch hooking length
More than 5.0 mm (0.197 in)
Hood
Secondary latch
Bumper rubber adjustment
● Adjust so that hood is aligned with fender. At that time deflection is approx. 2 mm (0.08
in).
[Bumper rubber free height is approx. 13 mm (0.51 in).]
20.6 - 26.5
(2.1 - 2.7,
15 - 20)
BODY END
Body Front End (Cont’d)
Hood adjustment
CS101
.
.
C205
C205
Bumper fascia assembly
.
.
.
.
: Bumper assembly mounting bolts, screw & clips
: N·m (kg-m, ft-lb)
BT-6
Fog lamp
NBT033
BODY END
Body Rear End and Opener
4-DOOR SEDAN
●
●
●
● When removing or installing trunk lid, place a cloth or other padding on rear fender panels. This prevents vehicle body from being scratched.
Bumper fascia is made of plastic. Do not use excessive force and be sure to keep oil away from it.
Trunk lid adjustment: Adjust at hinge-trunk lid portion for proper trunk lid fit.
Trunk lid lock system adjustment: Adjust striker so that it is in the center of the lock. After adjustment, check trunk lid lock operation.
●
●
WARNING:
● Be careful not to scratch trunk lid stay when installing trunk lid.
●
A scratched stay may cause gas leakage.
The contents of the trunk lid stay are under pressure. Do not take apart puncture, apply heat or allow fire near it.
Opener cable: Do not attempt to bend cable using excessive force.
After installation, make sure that trunk lid and fuel filler lid open smoothly.
5.1 - 6.37
(0.52 - 0.65,
45.1 - 56.4)
.
.
Trunk lid lock key cylinder
Trunk lid lock
Upper
Spring holder
Actuator
Lower
.
5.1 - 6.37
(0.52 - 0.65, 45.1 - 56.4)
Opener handle
20.6 - 26.5
(2.1 - 2.7,
15 - 20)
Opener cable
Lock nut
Fuel filler lid opener & control
Trunk lid striker
.
5.1 - 6.37
(0.52 - 0.65,
45.1 - 56.4)
Cloth
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
NBT034
BT-7
V
V
V
V
V
V
BODY END
REMOVAL — Rear bumper assembly
Body Rear End and Opener (Cont’d)
Remove license plate lamp.
Remove clips
C203 securing left and right chipping protector.
Remove screws securing bumper fascia to left and right rear fenders.
Remove clips
CS101 securing bumper fascia to real panel.
Remove clips
C205 securing bumper fascia to rear panel upper.
Extract bumper fascia assembly.
SEC. 843 c 844 c 850 c 998
Trunk lid lock control Trunk lid adjustment
5.1 - 6.37
(0.52 - 0.65,
45.1 - 56.4)
Trunk lid stay
Trunk lid hinge
Fuel filler lid control
Trunk lid striker adjustment
.
C205
Bumper fascia assembly
Opener handle
C203
.
.
.
CS101
.
CS101
: N·m (kg-m, in-lb)
.
: Bumper assembly mounting clips and screws.
NBT035
BT-8
BODY END
Body Rear End and Opener (Cont’d)
5-DOOR HATCHBACK
●
●
●
●
Back door adjustment: Adjust at hinge-body portion for proper back door fit.
Back door lock system adjustment: Adjust lock & striker so that they are in the center. After adjustment, check back door lock operation.
WARNING:
● Be careful not to scratch back door stay when installing back door. A scratched stay may cause
● gas leakage.
The contents of the back door stay are under pressure. Do not take apart, puncture, apply heat or allow fire near it.
Opener cable: Do not attempt to bend cable using excessive force.
After installation, make sure that back door and fuel filler lid open smoothly.
12.7 - 15.7
(1.30 - 1.60,
9.4 - 11.6)
12.7 - 15.7
(1.30 - 1.60,
9.4 - 11.6)
20.6 - 26.5
(2.10 - 2.70,
15.2 - 19.5)
Opener handle Opener cable
Lock nut
Fuel filler lid opener & control
Key cylinder
Cloth
20.6 - 26.5
(2.10 - 2.70,
15.2 - 19.5)
V
V
V
V
V
V
REMOVAL — Rear bumper assembly
Remove license plate lamp
Remove clips
C203 securing left and right chipping protector.
Remove screws securing bumper fascia to left and right rear fenders.
Remove clips
CS101 securing bumper fascia to rear panel.
Remove clips
C205 securing bumper fascia to rear panel upper.
Extract bumper fascia assembly.
12.7 - 15.7
(1.30 - 1.60,
9.4 - 11.6)
.
5.1 - 6.37
(0.52 - 0.65, 45.1 - 56.4)
Actuator
: N·m (kg-m, ft-lb)
NBT036
BT-9
BODY END
Body Rear End and Opener (Cont’d)
SEC. 850 c 900 c 905
Back door lock adjustment
Back door lock control
Back door stay installation
Back door hinge adjustment
Opener handle
Fuel filler lid control
Back door striker adjustment
.
CS205
C203
.
Bumper fascia assembly
.
CS101
.
CS101
BT-10
.
: Bumper assembly mounting clips and screws.
NBT037
BODY END
Body Rear End and Opener (Cont’d)
WAGON
●
●
●
●
Back door adjustment: Adjust at hinge-body portion for proper back door fit.
Back door lock system adjustment: Adjust lock & striker so that they are in the center. After adjustment, check back door lock operation.
WARNING:
● Be careful not to scratch back door stay when installing back door. A scratched stay may cause
● gas leakage.
The contents of the back door stay are under pressure. Do not take apart, puncture, apply heat or allow fire near it.
Fuel filler lid opener cable: Do not attempt to bend cable using excessive force.
After installation, make sure that back door and fuel filler lid open smoothly.
12.7 - 15.7
(1.30 - 1.60,
9.4 - 11.6)
12.7 - 15.7
(1.30 - 1.60,
9.4 - 11.6)
.
20.6 - 26.5
(2.10 - 2.70,
15.2 - 19.5)
Opener handle
Lock nut
Opener cable
.
.
Fuel filler lid opener & control
2.9 - 3.8 N·m
(0.30 - 0.39 kg-m,
25.7 - 33.6 in-lb)
.
12.7 - 15.7
(1.30 - 1.60,
9.4 - 11.6)
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
V
V
V
V
REMOVAL — Rear bumper assembly
Remove clips
C203 securing left and right chipping protector.
Remove screws securing bumper fascia to left and right rear fenders.
Remove clips
C205
(small) securing bumper fascia to rear panel.
Remove clips
C205
(large) securing bumper fascia to rear panel upper.
Extract bumper fascia assembly.
Actuator
12.7 - 15.7
(1.30 - 1.60,
9.4 - 11.6)
.
5.1 - 6.37
(0.52 - 0.65,
45.1 - 56.4)
Key cylinder
NBF270
BT-11
BODY END
Body Rear End and Opener (Cont’d)
Back door lock control
Back door stay installation
Back door lock adjustment
Back door hinge adjustment
Fuel filler lid control
Rear fender cover
Back door striker adjustment
Opener handle
Bumper fascia assembly
BT-12
*
: Bumper assembly mounting clips and screws.
NBF271
●
●
Front Door
For removal of door trim, refer to ‘‘Door Trim’’ in ‘‘INTERIOR TRIM’’ for details, BT-24.
After adjusting door or door lock, check door lock operation.
SEC. 800 c 803 c 805
DOOR
2.93 - 3.82
(0.30 - 0.39,
25.9 - 33.8)
Door-hinge adjustment
5.1 - 6.37
(0.52 - 0.65, 45.1 - 56.4)
5.1 - 6.37
(0.52 - 0.65,
45.1 - 56.4)
6.08 - 7.75
(0.62 - 0.79,
53.8 - 68.6)
5.1 - 6.37
(0.52 - 0.65,
45.1 - 56.4)
6.08 - 7.75
(0.62 - 0.79,
53.8 - 68.6)
6.08 - 7.75
(0.62 - 0.79,
53.8 - 68.6)
6.08 - 7.75
(0.62 - 0.79,
53.8 - 68.6)
20.6 - 26.5
(2.1 - 2.7,
15 - 20)
Door-hinge adjustment
20.6 - 26.5 (2.1 - 2.7, 15 - 20)
Striker adjustment
13 - 16
(1.3 - 1.6,
9 - 12)
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Apply grease
NBT038
BT-13
SEC. 820 c 823 c 825
DOOR
Rear Door
1.47- 1.86
(0.15 - 0.19,
13.0 - 16.5)
5.1 - 6.37
(0.52 - 0.65,
45.1 - 56.4)
6.08 - 7.75
(0.62 - 0.79,
53.8 - 68.6)
Door-hinge adjustment
20.6 - 26.5
(2.1 - 2.7,
15 - 20)
5.1 - 6.37
(0.52 - 0.65,
45.1 - 56.4)
5.1 - 6.37
(0.52 -0.65,
45.1 - 56.4)
6.08 - 7.75
(0.62 - 0.79,
53.8 - 68.6)
6.08 - 7.75
(0.62 - 0.79,
53.8 - 68.6)
Door-hinge adjustment
20.6 - 26.5
(2.1 - 2.7,
15 - 20)
Striker adjustment
13 - 16
(1.3 - 1.6,
9 - 12)
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Apply grease
NBT039
BT-14
INSTRUMENT PANEL
CAUTION:
● Disconnect both battery cables in advance.
●
●
●
Disconnect air bag system line in advance.
Never tamper with or force air bag lid open, as this may adversely affect air bag performance.
Be careful not to scratch pad and other parts.
REMOVAL — Instrument panel assembly
Instrument panel assembly Combination meter Audio & A/C control Console box
Remove air bag module (driver’s) and steering wheel.
Refer to ‘‘SUPPLEMENTAL RESTRAINT SYSTEM’’ in RS section for details.
Steering column cover and combination switch
● Remove screws.
Instrument lower panel on driver side
● Remove screws.
Cluster lid A
● Remove screws.
Combination meter
● Remove screws and disconnect harness connectors.
Audio
Center ventilator
●
●
Remove screws.
Pull out with a miniature flat-bladed screwdriver.
A/C or heated control
● Remove screws.
Audio bracket
Glove box assembly
●
●
Remove glove box pin.
Then disconnect passenger air bag module connector.
Passenger air bag module
● Refer to ‘‘SUPPLEMENTAL RESTRAINT SYSTEM’’ in RS section for details.
Lower cover
● Remove clip
AT finisher or MT shift lever boot
Rear console box
● Remove console mask and screws.
Front console box
● Remove screws and bolts.
Front defroster grill
● Disconnect harness connector.
Front pillar garnish
●
Refer to ‘‘Side and Floor Trim’’ in ‘‘INTERIOR TRIM’’ for details, BT-18.
Instrument panel and pads
●
●
Remove nuts and bolts.
Remove door mirror switch and disconnect the connector.
BT-15
SEC. 248 c 251 c 272 c 487 c 680 c 685 c 969
INSTRUMENT PANEL
.
2.8 - 4.8 (0.29 - 0.49, 24.8 - 42.5)
.
.
.
.
14.7 - 24.5
(1.50 - 2.5,
10.8 - 18.1)
.
Metal clip Metal clip
Metal clip
Metal clip
Metal clip
BT-16
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
.
: Instrument panel assembly mounting bolts & nuts.
NBT040
Metal clip
Metal clip
INSTRUMENT PANEL
.
Cloth
.
Pull
Bracket
Bolt
Metal clip
Hook
Metal clip
NBT041
BT-17
INTERIOR TRIM
Side and Floor Trim
CAUTION:
Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from garnishes.
REMOVAL — Body side trim
V
V
V
V
V
V
V
V
V
V
V
V
4-door sedan
Remove front and rear seats. Refer to ‘‘SEAT’’ for details, BT-40.
Remove front and rear kicking plates.
Remove dash side lower finishers.
Remove front and rear body side welts.
Remove front pillar garnishes.
Remove center pillar lower garnishes.
Remove front seat belt shoulder adjustment anchor bolt covers and anchor bolts (Refer to ‘‘SEAT
BELTS’’ in RS section for anchor bolt details).
Remove center pillar upper garnishes.
Remove rear pillar garnishes.
High-mount stop lamp.
Remove rear parcel shelf finisher.
Remove welt.
Remove seatback finisher.
SEC. 678 c 749 c 769 c 799
Metal clip
Metal clip
Metal clip
Metal clip
Metal clip
Metal clip
X: Metal clips
YBT011
BT-18
Metal clip
Metal clip
Garnish
INTERIOR TRIM
Side and Floor Trim (Cont’d)
Metal clip
Metal clip
Metal clip
Metal clip
Metal clip
Metal clip
YBT012
BT-19
INTERIOR TRIM
Side and Floor Trim (Cont’d)
REMOVAL — Body side trim
V
V
V
V
V
V
●
V
V
V
V
V
V
5-door hatchback
Remove parcel shelf before removing body side trim.
Remove front and rear seats. Refer to ‘‘SEAT’’ for details, BT-40.
Remove front and rear kicking plates.
Remove dash side lower finishers.
Remove front and rear body side welts.
Remove front pillar garnishes.
Remove center pillar lower garnishes.
Remove front seat belt shoulder adjustment anchor bolt covers and anchor bolts (Refer to ‘‘SEAT
BELTS’’ in RS section for anchor bolt details).
Remove center pillar upper garnishes.
Remove rear parcel shelf side finishers.
Remove rear pillar finishers.
Remove luggage room rear plate.
Remove luggage room rear finisher.
Remove luggage room side lower finishers.
SEC. 678 c 749 c 769 c 799
Metal clips
Metal clip
Metal clip
Metal clip
Metal clip
Metal clip
Metal clip
Metal clip
Metal clip
Metal clip
X : Metal clips
NBT042
BT-20
Metal clip
Metal clip
Garnish
INTERIOR TRIM
Side and Floor Trim (Cont’d)
Metal clip
Metal clip
Metal clip
Metal clip
Metal clip
Metal clip
Metal clip
Metal clip
Metal clip
Metal clip
YBT014
BT-21
INTERIOR TRIM
Side and Floor Trim (Cont’d)
REMOVAL — Body side trim
V
V
V
V
V
V
●
V
V
V
V
V
V
Wagon
Remove parcel shelf before removing body side trim.
Remove front and rear seats. Refer to ‘‘SEAT’’ for details, BT-40.
Remove front and rear kicking plates.
Remove dash side lower finishers.
Remove front and rear body side welts.
Remove front pillar garnishes.
Remove center pillar lower garnishes.
Remove front seat belt shoulder adjustment anchor bolt covers and anchor bolts (Refer to ‘‘SEAT
BELTS’’ in RS section for anchor bolt details).
Remove center pillar upper garnishes.
Remove luggage room side center finisher.
Remove luggage room side upper finisher.
Remove luggage room rear plate.
Remove luggage room rear finisher.
Remove luggage room side lower finisher.
Metal clip
Metal clips
Metal clip
.
Clip
Metal clip
Metal clip
Clip
Metal clip
Metal clip
Guard net hook
: Metal clips
NBF273
BT-22
Metal clip
INTERIOR TRIM
Side and Floor Trim (Cont’d)
Metal clip
Metal clip
Metal clip
Garnish
Metal clip
Metal clip
Metal clip
Metal clip 12.7 - 15.7 N·m
(1.30 - 1.60 kg-m,
9.4 - 11.6 ft-lb)
Metal clip
NBF272
BT-23
INTERIOR TRIM
Door Trim
V
V
V
V
REMOVAL — Door trim
Remove pull handle.
Remove power window switch assembly and disconnect the connector (Power window models).
Remove window regulator handle (Manual window models).
Remove bolts, screws and clips
C101 securing door finisher.
Lift out door finisher.
SEC. 251 c 267 c 809 c 828 clips
Metal clip
Hook
Manual window regulator handle
Removal
Push
Flat-bladed screwdriver
Squeeze the regulator handle clip in place with a screwdriver and remove the regulator handle from the regulator shaft.
Set the regulator handle clip as shown in figure .
Installation
Front
Push the regulator handle to install it into the regulator shaft.
Install the regulator handle in place as shown in the figure with the window completely closed.
YBT015
BT-24
INTERIOR TRIM
Roof Trim
REMOVAL — Headlining
V
V
V
V
V
V
V
V
V
V
4-door sedan
Remove front and rear seats. Refer to ‘‘SEAT’’ for details, BT-40.
Remove front and rear seat belts. Refer to ‘‘SEAT BELTS’’ in RS section for details.
Remove body side trim. Refer to ‘‘Side and Floor Trim’’ for details, BT-18.
Remove sunroof switch. (Models equipped with electric sunroof)
Remove handle and lamp cover. (Models equipped with manual sunroof)
Remove sunroof welt. (Models equipped with sunroof)
Remove sun visors.
Remove interior lamp assembly.
Remove assist grips.
Remove clips
C103 securing headlining.
Remove headlining.
SEC. 264 c 738 c 963 c 964
Manual type
C103
NBT043
BT-25
INTERIOR TRIM
Roof Trim (Cont’d)
REMOVAL — Headlining
V
V
V
V
V
V
V
V
V
V
5-door hatchback
Remove front and rear seats. Refer to ‘‘SEAT’’ for details, BT-40.
Remove front and rear seat belts. Refer to ‘‘SEAT BELTS’’ in RS section for details.
Remove body side trim. Refer to ‘‘Side and Floor Trim’’ for details, BT-20.
Remove sunroof switch. (Models equipped with electric sunroof)
Remove handle and lamp cover. (Models equipped with manual sunroof)
Remove sunroof welt. (Models equipped with sunroof)
Remove sun visors.
Remove interior lamp assembly.
Remove assist grips.
Remove roof rear garnish.
Remove headlining.
SEC. 264 c 738 c 963 c 964
Manual type
BT-26
Metal clip
Metal clip
NBT044
INTERIOR TRIM
Roof Trim (Cont’d)
REMOVAL — Headlining
V
V
V
V
V
V
V
V
V
V
V
V
V
V
Wagon
Remove front and rear seats. Refer to ‘‘SEAT’’ for details, BT-40.
Remove front and rear seat belts. Refer to ‘‘SEAT BELTS’’ in RS section for details.
Remove body side trim. Refer to ‘‘Side and Floor Trim’’ for details, BT-22.
Remove sunroof switch. (Models equipped with electric sunroof)
Remove handle and lamp cover. (Models equipped with manual sunroof)
Remove sunroof welt. (Models equipped with sunroof)
Remove sun visors.
Remove interior lamp (center) and interior lamp (rear).
Remove assist grips.
Remove clips
C103
.
Remove luggage net escutcheons.
Remove roof rear garnish.
Remove speakers.
Remove headlining.
C103
Manual type
Metal clip
BT-27
Metal clip
NBT045
SEC. 849
INTERIOR TRIM
Trunk Room Trim
Metal clip
Front
Metal clip
YBT018
BT-28
INTERIOR TRIM
Luggage Room Trim
BT-29
NBF275
V
V
V
V
REMOVAL — Back door trim
Remove back door lower finisher.
Remove back door upper finisher.
Remove back door side finisher.
Remove high-mounted stop lamp.
INTERIOR TRIM
Back Door Trim
Metal clip
Metal clip
Metal clip
2.9 - 3.8 N·m (0.30 - 0.39 kg-m, 26.0 - 33.9 in-lb)
Metal clip
Metal clip Metal clip
Metal clip
NBT054
BT-30
EXTERIOR
BT-31
NBT051
EXTERIOR
BT-32
NBT052
Hood front sealing rubber
SEC. 650
Hood front sealing rubber
Radiator core support sealing rubber
EXTERIOR
Windshield upper molding
SEC. 720
1. Cut off sealant at glass end.
2. Clean the side on which panel was mounted.
3. Set molding fastener and apply primer to body panel, and apply sealant to body.
YBT020
Cowl top seal and cowl top grille
SEC. 660
Cowl top seal
Cowl top grille
Windshield side molding
Mounted with screws.
YBT021
Molding
Clip
Fastener
Glass
Dam rubber
Double-faced adhesive tape
Apply primer
Apply sealant
Sealant
4. Install molding by aligning the molding mark located on center with vehicle center.
Be sure to install tightly so that there is no gap around the corner.
SBF342H
Drip weatherstrip
Front pillar
Drip weatherstrip
Drip weatherstrip
Body panel
Upper
Windshield side molding
Screw
YBT022
BT-33
Front
SEC. 720
NBT058
Body side welt
EXTERIOR
Door outside molding
Front door
SEC. 800
Screw
Door weatherstrip
EC. 800 c 820
Clip
Outside
Clip
SBT043
Clip Clip
Door outer molding
Clip
Door outer panel
Rear door
SEC. 820
Screw
Door outer molding
Clip
Door panel
Sunroof lid weatherstrip
SEC. 736
Roof panel
Glass lid
SBT067
YBT024
Front
Sunroof rail assembly
Sunroof lid weatherstrip
YBT025
BT-34
Side guard molding
SEC. 766
EXTERIOR
Rear window lower molding
Rear window glass
Rear window lower molding
Locating pins
: Double-faced adhesive tape
Removal: Remove molding by cutting around its perimeter.
Installation: Refer to ‘‘Rear window’’.
YBT027
Trunk lid weatherstrip
SEC. 843
Marking at vehicle center
Vehicle center
Heat gun
YBT026
● With a vehicle coated with Hard Clear Coat, use double-faced 3M adhesive tape Product
No. 5572 or equivalent, after priming with
3M primer Product No. N-200 or C-100 or equivalent.
Rear window upper molding
Basically the same as windshield upper molding.
Refer to Windshield upper molding.
Bonding portion SBT069
Back door window molding
5-door hatchback
Back door molding Back door molding
Glass
Glass
Double side adhesive tape
Back door molding
Glass
Back door molding
300 (11.81)
60
(2.36)
BT-35
Back door molding
Glass
Unit: mm (in)
YBT050
Wagon
See ‘‘Back door window’’. Refer to BT-57.
Back door weatherstrip
Wagon
Vehicle center
EXTERIOR
5-door hatchback
Bonding point
Vehicle center
NBF278
Bonding portion
YBT056
BT-36
EXTERIOR
●
●
Rear combination lamp
Rear combination lamps are installed with nuts and butyl sealant.
When removing inside rear combination lamp (installed on back door), first remove ‘‘Back door finisher’’.
Refer to Back door finisher.
SEC. 265
Heat gun
Heat gun
Heat gun
Butyl seal
Butyl seal
Heat gun
●
●
Apply butyl seal evenly as it tends to become thin in the corners.
Warm up lamp assembly area to a temperature of a little below 60°C (140°F).
NBT056
Center mud guard
SEC. 767
CF118
C205
Double-faced adhesive tape
NBT046
BT-37
EXTERIOR
Front hood grille
Hook
Hook
Hook
NBT047
Roof rail
5.1 - 6.4 N·m
(0.52 - 0.65 kg-m,
45.1 - 56.6 in-lb)
Roof rail
Clip
Front
Hook
Pawl
Center
Hook
Clip
Rear
NBF280
BT-38
Back door finisher
EXTERIOR
Nut x 8
NBF279
BT-39
SEAT
●
●
When removing or installing seats with side air bag module, be sure to disconnect or connect side air bag sub harness connector.
When removing or installing the seat trim, handle it carefully to keep dirt out and avoid damage.
.
For Wiring Diagram, refer to ‘‘POWER SEAT’’ in EL section.
Front Seat
Manual seat
18 - 24
(1.9 - 2.4, 14 - 17)
Side airbag sub harness connector
21 - 26
(2.1 - 2.7, 15.5 - 19.2)
18 - 24
(1.9 - 2.4, 14 - 17)
BT-40
: N·m (kg-m, ft-lb)
18 - 24
(1.9 - 2.4, 14 - 17)
NBT048
Power Seat
SEAT
Front Seat (Cont’d)
18 - 24
(1.9 - 2.4, 14 - 17)
21 - 26
(2.1 - 2.7, 15.5 - 19.2)
Side airbag sub harness connector
18 - 24
(1.9 - 2.4, 14 - 17)
BT-41
18 - 24
(1.9 - 2.4, 14 - 17)
: N·m (kg-m, ft-lb)
NBF266
SEAT
●
●
●
Heated Seat
When handling seat, be extremely careful not to scratch heating unit.
To replace heating unit, seat trim and pad should be separated.
Do not use any organic solvent, such as thinner, benzene, alcohol, gasoline, etc. to clean trims.
Seatback heating unit removal & installation
Seatback trim
Heating unit
Thermostat
Trim temperature
°C (°F)
Thermostat operation
Seat cushion trim
.
For Wiring Diagram, refer to ‘‘HEATED SEAT’’ in EL section.
Increasing to
35 - 45
(95 - 113)
OFF
Decreasing to
15 - 25
(59 - 77)
ON
SBF424H
BT-42
SEAT
● When removing or installing the seat trim, carefully handle it to keep dirt out and avoid damage.
Rear Seat
Rear seat back hinge (center)
& hook
Rear seat back striker (RH)
Rear seat hook
.
23.0 - 28.0
(2.4 - 2.9, 16.9 - 20.6)
Rear seat back hinge (LH)
Rear seat back hinge
(center)
.
43.1 - 54.9
(4.4 - 5.6,
31.8 - 40.5)
20.6 - 26.5
(2.1 - 2.7,
15.2 - 19.5)
12.7 - 15.7
(1.3 - 1.6,
9.4 - 11.6)
Suitable tool
: N·m (kg-m, ft-lb) : N·m (kg-m, in-lb)
NBF285
BT-43
Type 1
SEC. 880
SEAT
Rear Seat (Cont’d)
: N·m (kg-m, ft-lb)
Rear seat hook
Rear seat hinge
12.7 - 15.7
(1.3 - 1.6, 9.4 - 11.6)
YBT054
BT-44
Type 2
SEC. 880
Rear seat back striker (RH)
SEAT
Rear Seat (Cont’d)
Rear seat back striker (LH)
Rear seat back hinge
Rear seat hook Rear seat hinge
Rear seat side back hinge
43.1 - 54.8
(4.4 - 5.5,
32 - 40)
12.7 - 15.7
(1.3 - 1.6,
9.4 - 11.6)
43.1 - 54.8
(4.4 - 5.5,
32 - 40)
Tightening sequence
A: Finger
B tight
B: 43.1 - 54.8
(4.4 - 5.5,
32 - 40)
C: 43.1 - 54.8
(4.4 - 5.5,
32 - 40)
.
12.7 - 15.7
(1.3 - 1.6,
9.4 - 11.6)
5.1 - 6.47 (0.52 - 0.66, 45.1 - 57.3)
A, C 12.7 - 15.7
(1.3 - 1.6, 9.4 - 11.6)
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
NBT057
BT-45
SUNROOF
ADJUSTMENT
Install motor & limit SW assembly and sunroof rail assembly in the following sequence:
1. Arrange equal lengths of link and wire assemblies on both sides of sunroof opening.
2. Connect sunroof connector to sunroof switch and positive (+) power supply.
3. Set lid assembly to fully closed position by operating open/tilt sunroof switch.
4. Fit outer side of lid assembly to the surface of roof on body outer panel.
5. Remove motor, and keep sunroof switch pressed to rear side until motor pinion gear reaches the end of its rotating range.
6. Install motor.
7. Check that motor drive gear fits properly in wires.
8. Press front side of sunroof switch to check lid assembly for normal tilting.
9. Check sunroof lid assembly for normal operations (tilt-up, tilt-down, open, and close).
Front
Lid assembly
Rear
Tilting up & down range
Outer body panel
Closing & opening range
Closing & opening range
SBF920F
BT-46
SUNROOF
REMOVAL
●
●
●
After any adjustment, check sunroof operation and lid alignment.
Handle finisher plate and glass lid with care so not to cause damage.
It is desirable for easy installation to mark each point before removal.
CAUTION:
Always work with a helper.
Link and wire assembly
Sunroof frame assembly
Shade assembly Lid assembly
Tilt glass lid up.
Sunroof lid mount screws
Lid assembly
Rear drain mount screws
Rear drain assembly
Operate sunroof switch to tilt glass lid down.
Shade assembly
Sunroof switch/interior accessories/headlining (Models equipped with sunroof)
●
Refer to ‘‘Roof Trim’’ in ‘‘INTERIOR TRIM’’ for details, BT-25, BT-26, BT-27.
Motor switch bracket
Motor assembly
Wind deflector mount nuts
Wind deflector mount screws
Wind deflector assembly
Drain hoses
Sunroof unit bracket
Sunroof frame assembly
Guide stopper
Link and wire assembly
Motor assembly
BT-47
SUNROOF
.
For Wiring Diagram, refer to ‘‘ELECTRIC SUNROOF’’ in EL section.
SEC. 736
Screw
Lid assembly
Guide stopper
Shade assembly
Rear drain assembly
Rear drain screw
Link and wire assembly
Wind deflector assembly
Sunroof frame assembly
Wind deflector mounting screws
Wind deflector mounting nuts
Guide stopper
5.1 - 6.4
(0.52 - 0.65,
45.1 - 56.4)
Motor assembly
Motor switch bracket
Drain hose
5.1 - 6.4
(0.52 - 0.65,
45.1 - 56.4)
Manual type
Sunroof unit bracket
Drive
Handle
: N·m (kg-m, in-lb)
: Apply grease
NBT049
BT-48
Holder
SUNROOF
Using flat-bladed screwdriver, pry shade assembly holder off rail. Then pull shade assembly forward to remove it from rail.
Shade holder
Front
Shade ASSY
Rail
YBT060
Trouble Diagnoses
DIAGNOSTIC TABLE
NOTE: For diagnosing electric problem, refer to ‘‘ELECTRIC SUNROOF’’ in EL section.
Check item (Components)
Adjustment
Drain hoses
Weatherstrip
Wind deflector
Symptom
Reference page
Excessive wind noise
Water leaks
Sunroof rattles
Excessive operation noise
1
The numbers in this table mean checking order.
2
1
1
1
2
4
3
3
2
2
Link and wire assembly
3
3
Roof panel
WIND DEFLECTOR
1. Open lid
2. Check visually for proper installation.
3. Check to ensure a proper amount of petroleum jelly has been applied to wind deflector connection points; apply if necessary.
Wind reflector arm
Wind reflector
SBT331
Roof panel
4. Check that wind deflector is properly retracted by hand. If it is not, remove and visually check condition. (Refer to
removal procedures, BT-47). If wind deflector is damage,
replace with new one. If wind deflector is not damage, re-install properly.
Wind reflector arm
Wind reflector
SBT332
BT-49
SUNROOF
Trouble Diagnoses (Cont’d)
ADJUSTMENT
If any gap or height differences between lid and roof is found, check lid and adjust as follows:
SEC. 736
5.4 - 6.3 (0.213 - 0.248)
Roof panel
Unit: mm (in)
12 +1.2
-2.0
(0.47
+0.047
-0.079
)
0.7 ± 0.028 ± 0.039
Lid
Lid
33.1 ± 5
(1.303 ± 0.197)
Roof panel
SBT381
Gap Adjustment
1. Remove shade assembly. (Refer to removal procedures
2. Tilt lid up.
3. Loosen lid securing nuts (3 each on left and right sides), then tilt lid down.
4. Adjust lid from outside of vehicle so it resembles ‘‘A-A’’ as shown in the figure above.
5. Tilt lid up and down until it is adjusted to ‘‘B-B’’ as shown in the figure above.
6. After adjusting lid, tilt lid up and tighten nuts.
7. Tilt lid up and down several times to check that it moves smoothly.
Height difference adjustment
1. Tilt lid up and down.
2. Check height difference between roof panel and lid to see if it is as ‘‘A-A’’ as shown in the figure above.
3. If necessary, adjust it by using one of following procedures:
●
●
Adjust by adding or removing adjustments shim(s) between lid and link assembly.
If lid protrudes above roof panel, add shim(s) or plain washer(s) at sunroof mounting bracket or stud bolt locations to adjust sunroof installation as required.
BT-50
SUNROOF
Trouble Diagnoses (Cont’d)
DRAIN HOSES
Drain hose
SBT335
1. Remove headlining to access drain hose connections. (Refer
to ‘‘REMOVAL — Headlining’’ in ‘‘INTERIOR TRIM’’, BT-25,
2. Check visually for proper connections, damage or deterioration.
(The figure shows only the front side.)
Sunroof frame assembly
Drain hose
.
Sunroof drain hose
Grommet
Rear fender inner LH
SBT333
Front
Rear wheel house inner LH
3. If leakage occur around trunk room, remove trunk room side trim and check connecting area.
Check for proper connection, damage or tear.
4. Pour water into drain hoses and find damaged portion.
● If any damaged portion is found at each step, replace the damaged part.
SBT334
WEATHERSTRIP
● In the case of leakage around lid, close lid and pour water over lid to find damaged or gap portion.
1. Remove lid assembly. (Refer to removal procedures, BT-47,
for details).
2. Visually check weatherstrip for proper installation. If a gap exists between lid and weatherstrip, check for sufficient amount of butyl seal. If required, remove weatherstrip and apply butyl seal.
Refer to ‘‘EXTERIOR’’ BT-31 for details.
BT-51
SUNROOF
Trouble Diagnoses (Cont’d)
3. Check weatherstrip visually for damage, deterioration, or flattening.
● If any damage is found, replace weatherstrip.
CAUTION:
Do not remove weatherstrip except when replacing, or filling up butyl seal.
LINK AND WIRE ASSEMBLY
Before replacing a suspect part, carefully ensure it is the source of noise being experienced.
1. Check link to determine if coating film has been peeled of to such an extent that substrate is visible. Check also to determine if link is the source of noise. If it is, replace it.
2. Visually check to determine if a sufficient amount of petroleum jelly has been applied to wire or rail groove. If not, add petroleum jelly as required.
3. Check wire for any damage or deterioration. If any damage is found, remove rear guide (refer to removal procedures,
BT-47 for details), then replace wire.
BT-52
Cutting sealant
Glass
WINDSHIELD AND WINDOWS
REMOVAL
After removing moldings, remove glass using piano wire or power cutting tool and inflatable pump bag.
WARNING:
● Be careful not to scratch the glass when removing.
● Do not set or stand the glass on its edges. Small chips may develop into cracks.
SBF034B
Windshield glass
Windshield glass
Interior auto glass cut-out knife kit SBT472
Inflatable pump bag
SBT473
INSTALLATION
●
●
●
Use a genuine Nissan Urethane Adhesive Kit or equivalent and follow the instructions furnished with it.
While the urethane adhesive is curing, open a door window.
This will prevent the glass from being forced out by passenger compartment air pressure when a door is closed.
The molding must be installed securely so that it is in position and leaves no gap.
● Inform the customer that the vehicle should remain stationary until urethane adhesive has completed cured (preferably
24 hours). Curing time varies with temperature and humidity.
WARNING:
●
●
Keep heat and open flames away as primers and adhesive are flameable.
The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes.
●
●
Use in an open , well ventilated location. Avoid breathing the vapors. They can be harmful if inhaled. If affected by vapor inhalation, immediately move to an area with fresh air.
Driving the vehicle before the urethane adhesive has completely cured may affect the performance of the windshield in case of an accident.
CAUTION
● Do not use an adhesive which is past its usable term. Shelf
●
●
● life of this product is limited to six months after the date of manufacture. Carefully adhere to expiration or manufacture date printed on the box.
Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
Do not leave primers and adhesive cartridge unattended with their caps open or off.
The vehicle should not be driven for at least 24 hours or until the urethane adhesive has completely cured. Curing times varies depending on temperature and humidities. The curing time will increase under higher temperatures lower humidities.
BT-53
Body side
Windshield
Install spacer to panel
Cowl top
WINDSHIELD AND WINDOWS
Glass
Windshield and Rear Window
Glass side
Install dam rubber.
Windshield and rear window
8 (0.31)
Vehicle center
8 (0.31)
Spacer
455.4 mm (17.93 in)
Install molding fastener.
When installing it, heat body panel and fastener to approx. 30 to 40°C (86 to 104°F).
Windshield Upper & side molding fasteners
Fastener
Rear window
Panel
Double-faced adhesive tape
SBF017A
YBT033 joint portion
8 (0.31)
Apply sealant evenly
7 - 8 (0.28 - 0.31)
Dam rubber
Glass
Unit: mm (in)
YBT034
REPAIRING WATER LEAKS FOR WINDSHIELD
Leaks can be repaired without removing and reinstalling glass.
If water is leaking between caulking material and body or glass, determine the extent of leakage. This can be determined by applying water while pushing glass outward.
To stop the leak, apply primer (if necessary) and then sealant to the leak point.
BT-54
Primer portion
Body side
WINDSHIELD AND WINDOWS
Side Window
Glass side
.
A
A
A-A
B
B
Primer portion
B-B
Primer portion
Primer portion
A-A
Glass
Primer portion
Sealing portion and installation
A
A
Window glass
B
B
Primer portion
Primer portion
B-B
Glass
NBF283
Clip
(bonded on glass)
Glass
C-C
D
D
B
B
A
A
More than
8 (0.32)
More than
7 (0.28)
Clip
(bonded on glass)
D-D
More than
8 (0.32)
More than
7 (0.28)
Glass
Glass
Glass
Molding
Apply sealant evenly
Unit: mm (in)
NBF281
BT-55
WINDSHIELD AND WINDOWS
Back Door Window
● Construction and removal/reinstallation method of back door window are basically the same as those of windshield.
5-door hatchback
●
For details of moldings, refer to ‘‘EXTERIOR’’, BT-31.
Dam rubber portion (Glass side) Primer portion (Glass side)
Back door molding
Dam rubber
Primer
Primer portion (Body side)
Primer
30 (1.18)
Primer
Unit: mm (in)
Primer
Back door molding
Back door molding
Primer
Back door molding
Primer
Sealant portion (Body side) 400 (15.75)
28 (1.10) 41 (1.61) 33 (1.30)
33 (1.30)
18.4
(0.724)
41.2
(1.622)
33 (1.30)
Sealant quantity
12 - 15
(0.47 - 0.59)
7 - 8
(0.28 - 0.31)
8.75
(0.3445)
YBT035
BT-56
WINDSHIELD AND WINDOWS
Back Door Window (Cont’d)
Wagon
4.5 (0.2)
2 (0.1)
Pin
.
A-A
7 (0.28)
Glass
Glass side
16 (0.6)
Back door molding
Primer portion
Sealant
Back door molding
Glass
Body side
Glass
B-B
C-C
12 (0.47)
17 (0.7)
Primer portion
Unit: mm (in)
NBT055
BT-57
MIRROR
Door Mirror
CAUTION:
Be careful not to scratch door rearview mirror body.
.
For Wiring Diagram, refer to ‘‘POWER DOOR MIRROR’’ in EL section.
V
V
V
V
REMOVAL — Door mirror
Remove door trim. Refer to ‘‘Door Trim’’ for details, BT-24.
Remove inner cover from front corner of door.
Disconnect door mirror harness connector.
Remove bolts securing door mirror, then remove door mirror assembly.
SEC. 963
Pawl
Removal:
● Wrap flat-blade of screwdriver with a cloth to prevent scratching.
Do not insert too far. Push mirror away from car to release.
Mirror
Cloth
Flat-bladed screwdriver
Inside
BT-58
Outside
YBT036
MIRROR
Rearview Mirror
REMOVAL
Remove rearview mirror by pushing deflect spring with screwdriver as shown in the figure.
Windshield
Mirror assembly
Mounting bracket
Windshield
Mirror assembly
Mounting bracket
Mounting bracket location
Bracket
85 - 90 mm
(3.34 - 3.54 in)
Center of windshield
YBT049
Side view
NBT059
INSTALLATION
1. Install mounting bracket as follows:
(1) Determine mounting bracket position on windshield by measuring from top of windshield to top of mounting bracket as shown in the figure.
(2) Mark location on outside of windshield with wax pencil or equivalent.
(3) Clean attaching point on inside of windshield with an alcoholsaturated paper towel.
(4) Sand bonding surface of mounting bracket with sandpaper
(No. 320 or No. 360).
(5) Clean bonding surface of mounting bracket with an alcoholsaturated paper towel.
(6) Apply Loctite Adhesive 11067-2 or equivalent to bonding surface of mounting bracket.
(7) Install mounting bracket at premarked position and press mounting bracket against glass for 30 to 60 seconds.
(8) After five minutes, wipe off excess adhesive with an alcoholmoistened paper towel.
2. Install rearview mirror.
BT-59
BODY ALIGNMENT
●
●
●
●
●
●
All dimensions indicated in figures are actual ones.
When using a tracking gauge, adjust both pointers to equal length. Then check the pointers and gauge itself to make sure there is no free play.
When a measuring tape is used, check to be sure there is no elongation, twisting or bending.
Measurements should be taken at the center of the mounting holes.
An asterisk (*) following the value at the measuring point indicates that the measuring point on the other side is symmetrically the same value.
The coordinates of the measurement points are the distances measured from the standard line of ‘‘X’’,
‘‘Y’’ and ‘‘Z’’.
Vehicle center
Front axle center
Imaginary base line
‘‘Z’’: Imaginary base line
[200 mm below datum line
(‘‘0Z’’ at design plan)]
SBF874GB
Engine Compartment
MEASUREMENT
BT-60
Unit: mm
YBT038
MEASUREMENT POINTS
Cowl top
BODY ALIGNMENT
Engine Compartment (Cont’d)
Radiator core support side and Radiator core support
7 dia.
Unit: mm
Front
YBT039
.
Front suspension spring support and cowl top side
7 dia.
Front side member LH side
6.2 dia.
YBT040
Front side member RH side
YBT041
Front
YBT042
Hood lock stay and Radiator core support lower
Front
Radiator core support upper center and hood lock stay
.
YBT043 YBT044
YBT045
BT-61
MEASUREMENT
BODY ALIGNMENT
Underbody
BT-62
YBT046
MEASUREMENT POINTS
Bottom view of vehicle
Rear
BODY ALIGNMENT
Underbody (Cont’d)
14 dia.
18 dia.
16 dia.
12.5 dia.
LH side
16 dia.
14 dia.
12.5 dia.
16 dia.
12 dia.
16 dia.
RH side
Front coordinates
V , V x : 330 y : −650 z : 213
V , V x : 495 y : −490 z : 356.6
V , V x : 455 y : −35 z : 377.6
, x : 450 y : 70 z : 254
, x : 410 y : 310 z : 133.8
, x : 587 y : 405 z : 169.4
, x : 393 y : 500 z : 128.6
, x : 414.5
y : 1,210 z : 124.9
x : 145 y : 2,507 z : 250 x : 300 y : 2,550 z : 402.3
x : −300 y : 2,550 z : 428.3
x : 512 y : 2,900 z : 346.5
Rear coordinates
V , V x : 412.5
y : 1,625 z : 123.2
V , V x : 524 y : 2,005 z : 209
V , V x : 555 y : 2,085 z : 259 x : −544 y : 2,882 z : 347.7
V x : 542 y : 3,385.6
z : 339.4
V x : −570.5
y : 3,380 z : 346.5
12 dia.
16 dia.
Bolt head
Bolt head
12 dia.
16 dia.
18 dia.
Front
Unit: mm
Front and rear strut tower centers
Coordinates:
V , V x : 527.3
y : −5.1
z : 780.1
, x : 478 y : 2,522 z : 527.3
Front
Rear
V
,
, 88 dia.
60.8 dia.
YBT047
BT-63
NOTE
BODY ALIGNMENT
Underbody (Cont’d)
BT-64
பதிவிறக்கு
பொது இணைப்பு புதுப்பிக்கப்பட்டது
உங்கள் அரட்டைக்கான பொது இணைப்பு புதுப்பிக்கப்பட்டுள்ளது. You may view and manage your chat links after registration here.
ஆவண பொது இணைப்பு
விளம்பரம்
