SD-502

SDIO GPS Receiver

User Manual

2005/10

SD-502 SDIO GPS Receiver User Manual, version 1.1

1. SD-502 at a glance

LED

GPS Antenna

Cover page 2

SD-502 SDIO GPS Receiver User Manual, version 1.1

2. System Specification

Electrical Characteristics (Receiver)

Chipset

SiRF Start III

Frequency

L1, 1575.42 MHz

C/A Code

1.023 MHz chip rate

Channels

20 channel all-in-view tracking

Accuracy

Position Horizontal

10 meters, 2D RMS

1~5 meters, 2D RMS with WAAS corrected

Velocity

0.1 m/sec

Time

1 micro-second synchronized to GPS time

Datum

Datum

WGS-84 (default)

Acquistion Rate

Hot start

1 sec., average

Warm start

38 sec., average

Cold start

42 sec., average

Reacquisition

0.1 sec., average

Protocol

GPS Protocol

NMEA 0183 (default)

SiRF binary (secondary)

GPS Output format

GGA (1 sec), GSA (1 sec), GSV (5 sec), RMC (1 sec).

GLL and VTG are optional.

Dynamic Condition

Acceleration Limit

Less than 4g

Altitude Limit

18,000 meters (60,000 feet) max.

Velocity Limit

515 meters/sec (1,000 knots) max.

Jerk Limit

20 m/sec**3

Temperature

Operating

-10

°

C ~ +70

°

C

Humidity

5 ~ 95% non-condensing

Power

Voltage

3.3 V

Power Consumption

110 mA

Physical Characteristics

Dimension

95 mm x 30 mm x 13 mm

Weight

approximately 30 grams

Memory Size

512 MB

SDIO Specification

• Compliant with SDIO Card Specification Ver. 1.00

• Base on Bsquare SDIO Now!

page 3

SD-502 SDIO GPS Receiver User Manual, version 1.1

page 4

3. Introduction

SD-502 is a GPS Receiver with SDIO (Security Digital Input/Output) interface and an integrated built-in memory, which provides an impressive data capacity. The built-in 512 MB memory allows you to easily organize, store, and share files or documents. It also allows for tracking signals and large map data according to the mapping software usage. It’s sleek and stylish design of look can go with any kind of the Pocket PC. With light and handy appearance, it is convenient for you to put it in pocket and bring it to anywhere you go. Just plug it into your Pocket PC, and use it to receive the GSP signal right away! Its cylindrical antenna can receive the signal from all directions by 360 degree. It satisfies a wide variety of applications, including car navigation, personal touring navigation or tracking and even marine navigation purpose. With our professional manufacturing technology along with the cutting edge, SiRF Star III chipset, this receiver has provided higher sensitivity, lower power usage and more rapid time-to-fix!

3.1 Features

• SiRF Star III high performance and low power consumption chipset

• Built-in high sensitivity GPS antenna

• LED to show GPS fix or not fix

• Built-in super capacitor to reserve system data for rapid satellite acquisition

• SDIO interface

• Operating platform: Pocket PC 2003, Win CE.Net, WM2003

• Base on Bsquare SDIO Now!

• Built-in memory size: 512 MB

3.2 Package

Before you start up, make sure that your package includes the following items. If any item is missing or damaged, contact your dealer immediately.

• SDIO GPS Receiver and its cover.

• A CD (including the User Manual, Driver and the Testing Program.)

3.3 LED Function

GPS Status LED (Green):

• Blinking — GPS position is fixed

• Steady light — GPS position is not fixed

SD-502 SDIO GPS Receiver User Manual, version 1.1

3.4 Compatible Device

• Dell Axim X3 Pocket PC

• Dell Axim X30 Pocket PC

• Dell Axim X50 Pocket PC

• Dell Axim X50V Pocket PC

• HP iPAQ h1930 Pocket PC

• HP iPAQ h1940 Pocket PC

• HP iPAQ h2210 Pocket PC

• HP iPAQ h4150 Pocket PC

• HP iPAQ hx2410 Pocket PC

• HP iPAQ hx4700 Pocket PC

• HP iPAQ rx3115 Pocket PC

• Eten M500

• Mio 168

Devices listed above have been tested and proved to be compatible with SD-502. page 5

SD-502 SDIO GPS Receiver User Manual, version 1.1

page 6

4. Install Driver

You have to install the driver before you can use the SD-502 GPS receiver with your Pocket PC. The driver will be installed into the Pocket PC via the ActiveSync program. So, before you start, please make sure the ActiveSync has been installed and the Pocket PC is connected to your desktop

PC.

(1). Put the CD into CD-ROM drive. The AutoRun will start the installation program automatically.

Click on the

“Install Driver for WinCE”

button to install the driver. (or you can manually install it by double click the “ GlobalSatSDGPS.exe” from the root directory of the CD. )

(2). Click the

Next

button on the Welcome dialog box and click

Yes

button on the End User

License Agreement dialog box.

SD-502 SDIO GPS Receiver User Manual, version 1.1

(3). Click

Yes

and

OK

on next 2 dialog boxes. Now the driver has been installed in your PDA.

page 7

(4). Click

Exit

button to close the AutoRun program.

SD-502 SDIO GPS Receiver User Manual, version 1.1

page 8

(5). If you want to check whether the driver has been properly installed or not, please do the following steps. In your PDA, tap

Start

/

Settings

, tap

System

tab and then

Remove Programs

icon. You will see the driver “

LEADCHAIN GPSDisk

” is on the list.

SD-502 SDIO GPS Receiver User Manual, version 1.1

page 9

5. Test the SD-502 GPS Receiver

You can use the testing program to see if the GPS Receiver is working correctly or not. The testing program only supports the Microsoft Windows CE and Pocket PC based PDA platform.

Note : For more detail about this GPSinfo testing program, please refer to the GPSinfo

User Manual, you can fi nd it in the root of CD. (GPSinfo_User_Manual_Eng.pdf)

To install the testing program, please follow the steps below:

(1). Put the CD into CD-ROM drive. The AutoRun will start the installation program automatically.

Click on the

“Install GPSinfo”

button to install the testing program. (or you can manually install it by double click the “ GPSinfo.exe” from the root directory of the CD.)

(2). Click the

Next

button to continue.

SD-502 SDIO GPS Receiver User Manual, version 1.1

page 10

(3). Click

Yes

and

OK

on next 2 dialog boxes. Now the GPSinfo program has been installed in your PDA.

(4). Click

Finish

button and fi nish the installation and click

Exit

button to close the AutoRun program.

SD-502 SDIO GPS Receiver User Manual, version 1.1

page 11

(5). If you want to check whether the program has been properly installed or not, please do the following steps. In your PDA, tap

Start

/

Settings

, tap

System

tab and then

Remove Programs

icon. You will see the “

GPS Information GPS Info

” is on the list.

SD-502 SDIO GPS Receiver User Manual, version 1.1

page 12

FCC Notices

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2)This device must accept any interference received, including interference that may cause undesired operation .

FCC RF Exposure requirements:

This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE

CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS

COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.