D-Link DAP-1320 User manual

Preface

D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes.

Revision

1.0

1.1

Manual Revisions

Date

September 5, 2012

August 27, 2013

Description

• Initial release for Revision A1

• Initial release for Revision A2

Trademarks

D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United

States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies.

Copyright © 2013 by D-Link Systems, Inc.

All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Systems, Inc.

D-Link DAP-1320 User Manual i

Table of Contents

Table of Contents

Preface ................................................................................. i

Tools ................................................................................................29

Manual Revisions ........................................................................... i

Admin .....................................................................................29

Trademarks ...................................................................................... i

System ....................................................................................30

Upgrade Firmware ..............................................................31

Statistics .................................................................................32

Product Overview ..............................................................1

Package Contents ......................................................................... 1

Minimum Requirements ............................................................ 2

Introduction ................................................................................... 3

What is a Wireless Extender? ............................................ 4

Features ............................................................................................ 5

Front/LED Indicator .............................................................. 6

Side and Bottom/WPS and Reset .................................... 7

Wireless Installation Considerations ...................................... 8

Wireless Security Options ...............................................33

Security Protocols ...............................................................33

Encryption .............................................................................34

Authentication .....................................................................34

Configuring WPA/WPA2 Personal .........................................35

Installation .........................................................................9

Connect Your DAP-1320 to Your Router Using WPS ......... 9

Configuration ...................................................................11

Wireless Setup Wizard ...............................................................11

QRS Mobile App Setup .............................................................15

Web-based Configuration Utility ..........................................19

Login ........................................................................................19

Setup Wizard ........................................................................20

Home .......................................................................................23

Wi-Fi Settings .......................................................................24

Extended Wi-Fi Settings ...................................................25

Network Settings ................................................................26

Advanced Settings ........................................................26

Connecting to a Wireless Network .................................37

Connecting to Wireless Clients Using WPS .......................37

Windows® 8 ...................................................................................38

Windows® 7 ...................................................................................40

WPA/WPA2 ............................................................................40

Windows Vista® ............................................................................43

WPA/WPA2 ............................................................................44

WPS/WCN 2.0 .......................................................................46

Windows® XP ................................................................................47

WPA/WPA2 ............................................................................48

Troubleshooting ..............................................................50

Wireless Basics .................................................................52

What is Wireless? .........................................................................53

Tips ...................................................................................................55

D-Link DAP-1320 User Manual ii

Table of Contents

Networking Basics ...........................................................56

Windows® 8 Users ...............................................................56

Windows® 7/Vista® Users..................................................56

Windows® XP Users ............................................................56

Statically Assign an IP Address ..............................................57

Windows® 8 Users ...............................................................57

Windows® 7/ Vista® Users .................................................58

Technical Specifications ..................................................59

Contacting Technical Support ........................................60

Warranty ...........................................................................61

Registration .....................................................................68

D-Link DAP-1320 User Manual iii

Section 1 - Product Overview

DAP-1320 Wireless Range Extender

Wi-Fi Configuration Card

Quick Install Guide

If any of the above items are missing, please contact your reseller.

D-Link DAP-1320 User Manual 1

Section 1 - Product Overview

Minimum Requirements

Network Requirements

• IEEE 802.11n or 802.11g wireless clients

• IEEE 802.11n or 802.11g wireless router or access point

Computer with the following:

• Windows®, Macintosh, Android or Linux-based operating system

Web-based Configuration

Utility Requirements

Browser Requirements:

• Internet Explorer 6

• Safari 4

• Firefox

• Chrome

Windows

®

Users: Make sure you have the latest version of Java installed. Visit www.java.com

to download the latest version.

D-Link DAP-1320 User Manual 2

Section 1 - Product Overview

Introduction

The Wireless Range Extender (DAP-1320) enables you to extend your existing wireless network coverage by placing the Wireless

Range Extender in between your router and your wireless client devices. This is great for extending your wireless coverage to hard-to-reach places like basements, home offices or upstairs bedrooms that are distant from your wireless router. The Wireless

Range Extender is also ideal for mobile device connections.

Note: Place the DAP-1320 within equal distance of your existing network/router and wireless clients.

D-Link DAP-1320 User Manual 3

Section 1 - Product Overview

What is a Wireless Extender?

The DAP-1320 acts as a repeater to extend the range of an existing wireless network to provide better signal for parts of your home or office that may have poor or no reception. Your existing wireless signal will be rebroadcast by the DAP-1320, allowing you to reach the farthest corners of your home or office . The extended network can simply use the same network credentials as the existing network, or you can specify a different network name and password, giving you the flexibility to control network access.

Internet

Wireless Router

D-Link DAP-1320 User Manual

DAP-1320

Mobile Device

Computer

4

Section 1 - Product Overview

Features

• Faster Wireless Networking - The DAP-1320 provides up to 300Mbps* wireless connection with other 802.11n wireless clients. This capability allows users to participate in real-time activities online, such as video streaming, online gaming, and real-time audio.

• Extend Internet access for wireless devices - Allows you to extend your internet access throughout your home with devices such as laptops, smartphones, tablets and more.

• IEEE 802.11n and 802.11g Compliant - The DAP-1320 is still fully compatible with the IEEE 802.11g standards, so it can connect with existing 802.11g USB and Cardbus adapters.

* Maximum wireless signal rate derived from IEEE Standard 802.11g and 802.11n specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely affect wireless signal range.

D-Link DAP-1320 User Manual 5

Section 1 - Product Overview

Hardware Overview

Front/LED Indicator

1

LED Indicator

1 Power/Status

Color

Green

Amber

Status

Solid Green

Blinking Green

Description

The device is securely connected to a wireless router or access point.

The device is processing a connection after the WPS button has been pushed.

The device is off.

Light off

Blinking Amber The device is booting up.

Light off The device is not receiving power. Try a different outlet.

D-Link DAP-1320 User Manual 6

Section 1 - Product Overview

Hardware Overview

Side and Bottom/WPS and Reset

1

2

1

2

WPS Button

Reset Button

Press the WPS (Wi-Fi Protected Setup) button for a minimum of one second to automatically connect with Wi-Fi clients. When the LED on the front of the device turns solid green, this means the DAP-1320 is connected.

Press and hold the reset button for six seconds to reset the DAP-1320 to the factory default settings.

D-Link DAP-1320 User Manual 7

Section 2 - Installation

Wireless Installation Considerations

The D-Link wireless device lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business. The key to maximizing wireless range is to follow these basic guidelines:

1. Keep the number of walls and ceilings between the D-Link device and other network devices to a minimum.

Each wall or ceiling can reduce your adapter’s range from 3-90 feet (1-30 meters.) Position your devices so that the number of walls or ceilings is minimized.

2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a 45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick! Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception.

3. Building Materials make a difference. A solid metal door or aluminum studs may have a negative effect on range.

Try to position access points, wireless routers, and computers so that the signal passes through drywall or open doorways. Materials and objects such as glass, steel, metal, walls with insulation, water (fish tanks), mirrors, file cabinets, brick, and concrete will degrade your wireless signal.

4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF noise.

5. If you are using 2.4GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home security systems), your wireless connection may degrade dramatically or drop completely. Make sure your 2.4GHz phone base is as far away from your wireless devices as possible. The base transmits a signal even if the phone in not in use.

D-Link DAP-1320 User Manual 8

Section 2 - Installation

Installation

Connect Your DAP-1320 to Your Router Using WPS

The easiest and most secure way to connect your DAP-1320 to your the router or access point is with WPS (Wi-Fi Protected

Setup). Refer to your user manual for your router or access point to make sure you understand how to enable WPS. Once you know, follow the steps below:

Step 1 - Find an available outlet near your wireless router. Plug the

DAP-1320 in, and wait until the power LED is blinking amber.

DAP-1320

WPS Button

Step 2 - Press the WPS button on your wireless router.

Note: Usually the WPS LED will blink once it is pressed. Check your router’s user manual for more information.

Step 3 - Within one minute, press and hold the WPS button on the

DAP-1320 until the light starts blinking green and then release.

Allow up to two minutes for the WPS process to finish.

WPS Button

D-Link DAP-1320 User Manual 9

Section 2 - Installation

Step 4 - Your router or access point and DAP-1320 will be securely connected when the LED light turns solid green.

Note: If your devices are not connected, try moving your DAP-1320 closer

to your wireless router or access point and repeat steps 2 and 3.

Step 5 - You can now unplug and move the DAP-1320 to a location between your wireless router and the area that you need to extend wireless coverage to.

Step 6 - To connect your wireless clients to the DAP-1320, You can use the Wi-Fi Network Name (SSID) and the Wi-Fi Password located on your Wi-Fi Configuration Card. Or use WPS (Wi-Fi

Protected Setup). Refer to “Connecting to Wireless Clients

Using WPS” on page 37

.

Note: For your wireless client to connect to the DAP-1320, you must use the same Wi-Fi Network Name (SSID) and Wi-Fi Password

as your DAP-1320 that is located on the Wi-Fi Configuration Card. If you would like to change your Wi-Fi Network Name (SSID) and

Wi-Fi Password refer to

“Extended Wi-Fi Settings” on page 25.

D-Link DAP-1320 User Manual 10

Section 3 - Configuration

Configuration

Wireless Setup Wizard

Use a wireless computer or mobile device with a web browser to access the Setup Wizard. As an alternative , you can go to the

“Web-based Configuration Utility” on page 19.

1. Find an available wall outlet near your wireless router. Plug in the

DAP-1320, and wait until the power LED turns to a blinking amber.

This means the device is booting up.

DAP-1320

2. From your wireless computer, go to the Wireless Utility to display the available Wi-Fi Networks and select the Wi-Fi Network Name

(SSID) that is on the Wi-Fi Configuration Card (ex: dlink-a8fa). Then, enter the Wi-Fi Password which is also located on your Wi-Fi

Configuration Card. (ex: akbdj19368).

3. Open a web browser and enter http://dlinkap.local./. Or you can enter the IP address of the DAP-1320.*

* The default IP address is 192.168.0.50. Once the DAP-1320 connects to your router, it will get assigned a new

IP address based on your router/network’s DHCP settings. You will need to log in to your router and view the

DHCP table to see what IP address was assigned to the DAP-1320. The MAC address is printed on the label on the DAP-1320.

D-Link DAP-1320 User Manual

Wi-Fi Name(SSID) 2.4Ghz: dlink-2c19

Wi-Fi Name(SSID) 5GHz: dlink-2C1B-media

Password:gccnu80856

11

Section 3 - Configuration

4. By default, Admin is the user name. Enter the Admin Password

(blank by default) and click Login.

Note: If this is your first time logging into the DAP-1320, you will be directed to the Setup Wizard automatically.

5. Select your Language from the drop-down menu and click Next to continue.

6. If your wireless device supports WPS, click on Select this option if

your wireless device supports WPS (Wi-Fi Protected Setup). For manual setup, skip to Step 8 on the next page.

Next to continue. You will see instructions on the screen that say, Press the Push Button (physical or virtual) on the AP or Router...

D-Link DAP-1320 User Manual 12

Section 3 - Configuration

7. Press and hold the WPS button on your wireless router or access point until the light starts blinking green and then release. Allow up to two minutes for the WPS process to finish. When a connection is successfully established, the LED on the device should turn solid green.

Note: Refer to your router or access point’s user manual instructions

for the WPS process.

8. If your wireless device does not support WPS, click Select this

option if you want to set up your network manually.

WPS Button

9. Wait while your device scans for available Wi-Fi networks. You will see a list of networks found. Select the Wi-Fi Network you wish to use, and click Select.

Note: If the network you would like to connect to is not listed, click

Back and select the manual option again to perform another scan.

Make sure you are in range of your wireless router.

D-Link DAP-1320 User Manual 13

Section 3 - Configuration

10. If the wireless network you selected is secure, you will be prompted to enter the Wi-Fi Password.

11. The DAP-1320 will rebroadcast the Wi-Fi connection from the uplink router as an Extended Network. Enter an Extended Wi-Fi network

name and Extended Wi-Fi network password.

If you would like to use the same SSID and password as your uplink router, check the box at the bottom of the screen. This will extend the network that your router is currently broadcasting.

12. The setup process is now complete. A summary page will appear displaying the settings for both the connection to the Wi-Fi Network and the Extended Wi-Fi network. It is recommended that you make a note of this information for future reference.

D-Link DAP-1320 User Manual 14

Section 2 - Installation

QRS Mobile App Setup

The DAP-1320 can be set up from your iOS or Android smartphone or tablet device using the QRS Mobile app.

Search for QRS Mobile in the App Store or Google Play, or use your mobile device to scan the QR codes on the right to download the QRS Mobile app from the App Store (left) for your iOS device, or from Google Play (right) for your Android device.

For iOS For Android

Connect to the Wi-Fi Network that is displayed on the Wi-Fi

Configuration Card included in your package (ex: dlink-a8fa).

Then, enter the Wi-Fi Password also printed on the Wi-Fi

Configuration Card (akbdj1936).

D-Link DAP-1320 User Manual 15

Section 2 - Installation

Once your mobile device is connected, tap on the QRS Mobile icon.

Tap Start to continue.

QRS Mobile will first detect your DAP-1320, then scan for available

Wi-Fi networks. Select the Wireless Network you wish to extend and enter the Password if required.

D-Link DAP-1320 User Manual 16

Section 2 - Installation

Enter a Network Name (SSID) and a Password for the extended

Wi-Fi network. You may keep the existing SSID and password if you wish. Tap Next to continue.

By default, your DAP-1320 does not have an admin password for the

Web-based configuration utility. You can enter a Device Password.

Tap Next to continue.

D-Link DAP-1320 User Manual 17

Section 2 - Installation

A summary of your settings will be displayed. To complete the setup, tap Save to save your settings and reboot the device.

After configuration is complete, the following screen will appear.

You can follow the on-screen instructions to change your mobile device and laptop Wi-Fi settings to the wireless Network Name and Password you just created.

D-Link DAP-1320 User Manual 18

Section 3 - Configuration

Web-based Configuration Utility

Login

To access the web-based configuration utility for the DAP-1320 on your PC, first connect to your DAP-1320 wirelessly. Use the Wi-Fi

Network Name and Wi-Fi Password from your Wi-Fi Configuration

Card. Then open a web-browser (e.g., Internet Explorer, Chrome,

Firefox, or Safari) and enter http://dlinkap.local./. Or you can use the IP address of the DAP-1320, http://192.168.0.50.*

Enter the Admin Password (blank by default) and click Login.

Note: By default, Admin is the user name. If you did not create a password, it should be left blank.

The configuration interface will open to the Home page. If you have not yet configured an uplink network, the diagram will indicate there is no connection between the DAP-1320 and your router. Refer to

“Connect Your DAP-1320 to Your Router Using WPS” on page 9 ,

or click the Setup Wizard button.

* Once the DAP-1320 connects to your router using the default IP address, it will get assigned a new IP address based on your router/network’s DHCP settings. You will need to log in to your router and view the

DHCP table to see what IP address was assigned to the DAP-1320. The MAC address is printed on the label on the DAP-1320.

D-Link DAP-1320 User Manual 19

Section 3 - Configuration

Setup Wizard

From the Home page, click Setup Wizard. The Setup Wizard will guide you through the process to configuring your DAP-1320.

If you prefer to configure your W-Fi Nework settings manually, refer to

”Wi-Fi Settings” on page 24

.

1. Select your Language from the drop-down menu and click Next to continue.

2. If your wireless device supports WPS, click on Select this option

if your wireless device supports WPS (Wi-Fi Protected Setup).

For manual setup, skip to Step 4 on the next page .

Next to continue. You will see instructions on the screen that say, Press the Push Button (physical or virtual) on the AP or Router...

D-Link DAP-1320 User Manual 20

Section 3 - Configuration

3. Press and hold the WPS button on your wireless router or access point until the light starts blinking green and then release.

Allow up to two minutes for the WPS process to finish. When a connection is successfully established, the LED on the device should turn solid green.

Note: Refer to your router or access point’s user manual instructions

for the WPS process.

4. If your wireless device does not support WPS, click Select this

option if you want to set up your network manually as the configuration method.

WPS Button

5. Wait while your device scans for available Wi-Fi networks. You will see a list of networks found. Select the Wi-Fi Network you wish to use, click Select.

Note: If the network you would like to connect to isn’t listed, click

Back and select the manual option again to perform another scan.

Make sure you are in range of your wireless router.

D-Link DAP-1320 User Manual 21

Section 3 - Configuration

6. If the wireless network you selected is secure, you will be prompted to enter the Wi-Fi Password.

7. The DAP-1320 will rebroadcast the Wi-Fi connection from the uplink router as an Extended Network. Enter an Extended Wi-Fi network

name and Extended Wi-Fi network password.

If you would like to use the same SSID and password as your uplink router, check the box at the bottom of the screen. This will extend the network that your router is currently broadcasting.

8. The setup process is now complete. A summary page will appear displaying the settings for both the connection to the Wi-Fi

Network and the Extended Wi-Fi network. It is recommended that you make a note of this information for future reference.

D-Link DAP-1320 User Manual 22

Section 3 - Configuration

Home

The Home screen gives a summary of the current status of devices connected to the DAP-1320. Click on an icon for more information.

2 3 4

1

5

6

7

8

1

2

3

4

5

Setup Wizard

Home

Settings

Management

6 Uplink Router Status

7

8

Uplink Router

DAP-1320

Wi-Fi Clients

Click to launch the setup wizard. Refer to “Setup Wizard” on page 20 .

Click to navigate to the Current Status page (as shown above).

Click to change/view your Wi-Fi, Extended Wi-Fi, and network settings.

Click to change the login password, upgrade firmware, view data traffic statistics, save/load configuration files, reboot, and restore the DAP-1320 back to the factory default settings.

Click to display the network settings of the wireless network (if connected) or to connect to a network if not connected.

Displays the status of your connection to the wireless network you are “repeating”. A green check mark ( ) indicates a successful connection to your wireless router or access point. A red ( ) indicates no connection.

Click the Uplink Router icon to display a list of wireless networks you can connect the DAP-1320 to.

Click to view the details of both the uplink router network and the extended Wi-Fi network.

Click to display a list of clients (devices) currently connected to the DAP-1320.

D-Link DAP-1320 User Manual 23

Section 3 - Configuration

Wi-Fi Settings

From the Home page, click on the Settings drop-down menu at the top of the page and select Wi-Fi. Here you can configure the Wi-Fi Network you would like your DAP-1320 to connect to. Use Site Survey to scan available Wi-Fi networks so you can select the one you would like to extend.

Wireless Mode:

This is set to Repeater mode and cannot be changed.

Wi-Fi Network

Name (SSID):

Click Scan to use Site Survey to display available wireless networks within range of the DAP-1320. Select the one you want to extend. You can also type in the name (SSID) of the wireless network. The SSID is case-sensitive and must be entered exactly the same as your router or access point.

Security:

Select the security method that is being used by the wireless network that you have selected: WEP, WPA/WPA2, or None.

Password:

If you selected WEP or WPA/WPA2, you will be required to enter the password or security key for the network you are attempting to join.

Save:

Click Save to save the settings and return to the home page.

D-Link DAP-1320 User Manual 24

Section 3 - Configuration

Extended Wi-Fi Settings

From the Home page, click on the Settings drop-down menu at the top of the page, and select Extended Wi-Fi. This page allows you configure the settings for the DAP-1320’s extended wireless network.

Wi-Fi Name

(SSID):

This is the name of the DAP-1320’s extended network.

The DAP-1320 will rebroadcast the uplink router’s Internet connection under this SSID. You can also choose to make the

SSID and password for the extended network the same as the SSID and password for the uplink network. This means the DAP-1320 will extend the network that your router is currently broadcasting.

Security:

Select the type of wireless security you wish to use for the extended network. Select None, WEP, or WPA/WPA2

Personal (recommended).

Password:

Enter the password or network key that you wish to use for the extended network. You can also choose to make the password for the extended network the same as the password for the uplink network.

Save:

Click Save to save the settings and return to the home page.

D-Link DAP-1320 User Manual 25

Section 3 - Configuration

Network Settings

From the Home page, click on the Settings drop-down menu at the top of the page, and select Network. This page allows you to configure the Network Settings for the DAP-1320.

Device Name:

You may change the name of the device by editing the text in the text box. If you change this Device Name, you will need to enter http://xxxx.local./ (where “xxxx” corresponds to the name of the device) in the address bar of your web browser in order to access the configuration utility.

Advanced Settings

The Advanced Settings section of the Network Settings page allows you to configure both IPv4 and IPv6 settings that will be used by the DAP-1320’s extended network. Below is the IPv4 Device Management Interface. See the next page for IPv6 settings.

My LAN

Connection is:

Select whether you want the IP to have a Dynamic IP (DHCP) or Static IP address. Select Dynamic IP to obtain the IP address information automatically from your ISP (Internet

Service Provider.)

IP Address:

Enter the Static IP Address that you want to assign to the extended network AP. This address should be outside of the uplink router’s DHCP address pool.

Subnet Mask:

Enter the Subnet Mask.

Gateway

Address:

Enter the Gateway Address. (Usually this is the IP address of the uplink router.)

Primary DNS

Server:

Enter the address of the Primary DNS Server.

Secondary

DNS Server:

Enter the address of the Secondary DNS Server. This is optional but will provide backup if the primary server fails.

D-Link DAP-1320 User Manual 26

Section 3 - Configuration

IPv6 Device Management Interface: You can select Autoconfiguration (SLAAC/DHCPv6), Static IPv6, or Link-local only:

My IPv6

Connection is:

Select Autoconfiguration (SLAAC/DHCPv6) to have the

DAP-1320 automatically receive an IPv6 address from the uplink router.

Obtain DNS

Server Address:

You can select to Obtain IPv6 DNS Servers automatically, or you can select Use the following IPv6 DNS Servers and enter IPv6 DNS server addresses manually.

Primary DNS

Server:

If you selected the second option above, enter the Primary

DNS Server address.

Secondary DNS

Server:

Enter the Secondary DNS Server address. This is optional but will provide backup if the Primary DNS server fails.

My IPv6

Connection is:

Select Static IPv6 to manually assign an IP address to the

DAP-1320.

IPv6 Address:

Enter the IPv6 Address that you want to assign to the extended network AP. This address should be outside of the uplink router’s DHCP address pool.

Subnet Prefix

Length:

Enter the length of the IPv6 subnet prefix.

Default Gateway:

Enter the Default Gateway. (Usually this is the IP address of the uplink router.)

Primary DNS

Server:

Enter the Primary DNS Server address.

Secondary DNS

Server:

Enter the Secondary DNS Server address. This is optional but will provide backup if the primary server fails.

D-Link DAP-1320 User Manual 27

Section 3 - Configuration

My IPv6

Connection is:

Select Link-local only to only set an IPv6 address for the local network.

LAN IPv6 Link-

Local Address:

The Link-Local Address of the DAP-1320 that you use to access the Web-based management interface.

D-Link DAP-1320 User Manual 28

Section 3 - Configuration

Tools

Admin

From the Home page, click on the Management drop-down menu at the top of the page, and select Admin. This page will allow you to set a new password for the administrator account used to configure the DAP-1320. You may also enable graphical authentication (CAPTCHA) for added security.

Admin

Password:

Enter a password for the Admin login name.

Enable

Graphical

Authentication:

Use the slider to Enable Graphical Authentication, or

CAPTCHA. This provides an extra layer of security by requiring users to enter a code that is displayed on the screen. This can help prevent unauthorized users from gaining access to your wireless network.

Click Save to save settings.

D-Link DAP-1320 User Manual 29

Section 3 - Configuration

System

From the Home page, click on the Management drop-down menu at the top of the page, and select System. This page allows you to save or restore the settings for your DAP-1320, You can also reset or reboot your device.

Save Settings to Local

Hard Drive:

Save the current system settings to a file on the local hard drive of your computer. A file dialog will appear, allowing you to select a location and file name for the settings.

Load Settings from

Local Hard Drive:

Load the previously saved system settings from a file on the local hard drive.

Restore to Factory

Default Settings:

Restore the system settings to factory default settings.

This will erase all currently stored settings.

Reboot the Device:

Click Reboot to reboot the DAP-1320.

D-Link DAP-1320 User Manual 30

Section 3 - Configuration

Upgrade Firmware

From the Home page, click on the Management drop-down menu at the top of the page and select Upgrade. Here you can upgrade the firmware and language packs.

Firmware

Information:

This section displays the Current Firmware Version, as well as the date on which the current firmware version was released.

Check for New

Firmware:

Click Check For New Firmware to update Firmware

Information. If you discover there is new firmware available, you can download it to your computer.

Language Pack

Information:

This section will display the details about Current Language

Packs, or say None installed.

Upgrade

Firmware:

Click Select File to locate the firmware file on your local hard drive and perform a manual firmware upgrade.

Add a

Language Pack:

Click Select File to locate a language pack file on your local hard drive and upload the language pack.

D-Link DAP-1320 User Manual 31

Section 3 - Configuration

Statistics

From the Home page, click on the Management drop-down menu at the top of the page, and select Statistics. This page displays traffic statistics about the total number of packets transmitted and received.

Wi-Fi:

Click on the Wi-Fi tab to display the statistics for the connection between the DAP-1320 and the uplink router.

Clear:

Click the Clear button to reset the statistics.

Extended Wi-Fi:

Click on the Extended Wi-Fi tab to display the statistics for the connection between the DAP-1320 and any connected clients.

Clear:

Click the Clear button to reset the statistics.

D-Link DAP-1320 User Manual 32

Section 3 - Configuration

Wireless Security Options

What is the best way to secure your wireless computer network? There are several security protocols with various versions from which to choose. Depending on the wireless device, you may have to select from different levels of security. The description of security protocols, encryption and authentication that follows is intended to help you better understand your choices.

Security Protocols

WPA ( Wi-Fi Protected Access) and WPA2 (Wi-Fi Protected Access II ) are two security protocols that were developed by the Wi-Fi Alliance (WFA) to replace the less-secure WEP (Wired Equivalent Privacy). The WFA is a trade association that certifies Wi-Fi® products that are compliant with standards of interoperability. IEEE 802.11 is the set of specifications for implementing WLAN (Wireless Local Area Network) computer communication within the 2.4 to 5GHZ frequency bands. WLAN typically provides a connection between wireless devices to the Internet using an AP (access point).

WPA was originally referred to as the draft IEEE 802.11i standard, since it became available first, and was intended as an intermediate solution pending the availability of a full IEEE 802.11i standard. WPA2 was known as IEEE 802.11i-2004, the year it first became available. Wi-Fi devices that have been certified since 2006 generally support both WPA and WPA2.

WPS (Wi-Fi Protected Setup™) provides the easiest way to establish a secure wireless network for home or small office (SOHO) environments.

Introduced in 2007, WPS was created by WFA so that users who might otherwise be intimidated by the available security options could set up a secure network, and later add new devices, with a simple automated process. PBC (Push Button Configuration) requires just the push of a button.

Today most wireless devices, from routers to wireless printers and cameras, have a WPS button. WPS enables WPA2 security protocol.

D-Link DAP-1320 User Manual 33

Section 3 - Configuration

Encryption

WPA typically provides data encryption using TKIP (Temporal Key Integrity Protocol), which dynamically generates a new 128-bit key for each data packet that is transmitted between networks. WPA also has an integrity checking feature, designed to prevent a hacker from altering and re-sending the data packets.

WPA2 uses CCMP, for Counter Cipher Mode with Block Chaining Message Authentication Code Protocol, which uses a higher standard known as

AES (Advanced Encryption Standard). Therefore CCMP provides stronger security than TKIP. It was designed to provide data confidentiality, user authentication, and access control. WPS also uses a form of AES.

Authentication

With both WPA and WPA2, there are two types of authentication. For home or small office environments, WPA-Personal and WPA2-Personal are widely used. Enterprise networks for business use WPA-Enterprise and WPA2-Enterprise.

WPA-Personal, also called WPA-PSK (for Pre-shared key) / WPA2-Personal or WPA2-PSK:

Was designed for home and small office networks, and does not require an authentication server. Instead, each network device authenticates with the AP (access point) using the same key generated from an alpha-numeric password or passphrase. The password must be between 8-64 characters, and should not be a commonly known phrase.

WPA-Enterprise, also known as WPA-802.1X / WPA2-Enterprise or WPA2-802.1X:

Was designed for enterprise networks, and requires a RADIUS authentication server. The server uses a set of protocols to implement secure access for devices attempting to communicate with the network.

Although this is a more complicated setup, it provides the best security through EAP, for Extensible Authentication Protocol. EAP is actually a general framework, or architecture, for creation of keying material for message authentication. For example, when EAP is implemented in an 802.1X-enabled

Network Access Server (NAS) device, EAP methods are used to generate a secure private key that can be used for wireless encryption. This will ensure that only authorized network devices can access the network.

The WPS protocol uses EAP message exchanges for authentication. There are two methods:

1. Push-Button-Method means the user simply pushes a button on the access point or router, and within a minute or two pushes a button on the new wireless client device, in order to connect it to the wireless network.

2. The PIN method uses a Personal Identification Number that must be read from either a sticker, wireless configuration card, or the display on the wireless device. Support for this mode is mandatory for access points. However, there is some concern that the messages sent between the AP and the wireless client when attempting to validate the PIN could make the network vulnerable to attack. Most companies have fixed this issue with updated firmware.

D-Link DAP-1320 User Manual 34

Section 3 - Configuration

Configuring WPA/WPA2 Personal

If you did not enable wireless security during initial setup, it is recommended that you do so using the web-based configuration

utility. Establish wireless connectivity before enabling wireless security. If you prefer WPS, proceed to “Connecting to Wireless

Clients Using WPS” on page 37 .

1. Log into the web-based configuration by opening a web browser and entering http://dlinkap.local./.

2. Enter the Admin Password (blank by default) and click Login.

Note: By default, Admin is the user name. If you did not create a

password, it should be left blank.

3. The configuration interface will open to the Home page. Click on the Settings drop-down menu and select Wi-Fi. Then configure the Wi-Fi network you would like your DAP-1320 to connect to.

D-Link DAP-1320 User Manual 35

Section 3 - Configuration

4. Click Scan to use the Site Survey to display available wireless networks within range of the DAP-1320. Select the one you want to secure.

5. Select the security method you would like to use for the selected wireless network: WEP, WPA/WPA2, or None. Click Save to save settings.

D-Link DAP-1320 User Manual 36

Section 4 - Connecting to a Wireless Network

Connecting to a Wireless Network

Connecting to Wireless Clients Using WPS

The easiest and most secure way to connect your wireless devices to the DAP-1320 is WPS (Wi-Fi Protected Setup). Most wireless devices such as wireless adapters, media players, Blu-ray DVD players, wireless printers and cameras will have a WPS button (or a software utility with WPS) that you can press to connect to the DAP-1320. Please refer to your user manual for the wireless device you want to connect to make sure you understand how to enable WPS. Once you know, follow the steps below:

Step 1 - Press and release the WPS button on the DAP- 1320. The LED will blink green during the WPS process.

Step 2 - Within two minutes, press the WPS button on your wireless client (or launch the software utility and start the WPS process).

Step 3 - Allow up to two minutes to connect. Once the connection is successful the LED will be solid green.

D-Link DAP-1320 User Manual 37

Section 4 - Connecting to a Wireless Network

Windows® 8

1. Click on the wireless computer icon in your system tray (lower-right corner next to the time).

2. A list of available wireless networks will appear.

3. Click the wireless network (SSID) you want to connect to and then click Connect.

4. If the network is secure/encrypted, enter the Wi-Fi password

(security key) and click Next.

D-Link DAP-1320 User Manual 38

Section 4 - Connecting to a Wireless Network

5. Click either to enable or disable file sharing.

6. You will now be connected to your wireless network.

If you get a good signal but cannot access the Internet, confirm the encryption by reviewing the profile or check the TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information.

D-Link DAP-1320 User Manual 39

Section 4 - Connecting to a Wireless Network

Windows® 7

WPA/WPA2

It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used.

1. Click on the wireless icon in your system tray (lower-right corner).

Wireless Icon

2. The utility will display any available wireless networks in your area.

D-Link DAP-1320 User Manual 40

Section 4 - Connecting to a Wireless Network

3. Highlight the wireless network (SSID) you would like to connect to and click the Connect button.

If you get a good signal but cannot access the Internet, check your

TCP/IP settings for your wireless adapter. Refer to the Networking

Basics section in this manual for more information.

4. The following window appears while your computer tries to connect to the router.

D-Link DAP-1320 User Manual 41

Section 4 - Connecting to a Wireless Network

5. Enter the same security key or passphrase that is on your router and click Connect. You can also connect by pushing the WPS button on the router.

It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.

D-Link DAP-1320 User Manual 42

Section 4 - Connecting to a Wireless Network

Windows Vista®

Windows Vista® users may use the built-in wireless utility. If you are using another company’s utility, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows Vista® utility as seen below.

If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility.

or

Right-click on the wireless computer icon in your system tray (lower-right corner next to the time). Select Connect to a network.

The utility will display any available wireless networks in your area. Click on a network (displayed using the SSID) and click the Connect button.

If you get a good signal but cannot access the Internet, check you TCP/

IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information.

D-Link DAP-1320 User Manual 43

Section 4 - Connecting to a Wireless Network

WPA/WPA2

It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used.

1. Open the Windows Vista® Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower right corner of screen). Select Connect to a network.

2. Highlight the wireless network (SSID) you would like to connect to and click Connect.

D-Link DAP-1320 User Manual 44

Section 4 - Connecting to a Wireless Network

3. Enter the same security key or passphrase that is on your router and click Connect.

It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.

D-Link DAP-1320 User Manual 45

Section 4 - Connecting to a Wireless Network

WPS/WCN 2.0

The router supports Wi-Fi protection, referred to as WCN 2.0 in Windows Vista®. The following instructions for setting this up depends on whether you are using Windows Vista® to configure the router or third party software.

When you first set up the router, Wi-Fi protection is disabled and unconfigured. To enjoy the benefits of Wi-Fi protection, the router must be both enabled and configured. There are three basic methods to accomplish this: use Windows Vista’s built-in support for WCN 2.0, use software provided by a third party, or manually configure.

If you are running Windows Vista®, log into the router and click the Enable checkbox in the Basic > Wireless section. Use the

Current PIN that is displayed on the Advanced > Wi-Fi Protected Setup section or choose to click the Generate New PIN button or Reset PIN to Default button.

If you are using third party software to set up Wi-Fi Protection, carefully follow the directions. When you are finished, proceed to the next section to set up the newly-configured router.

D-Link DAP-1320 User Manual 46

Section 4 - Connecting to a Wireless Network

Windows® XP

Windows® XP users may use the built-in wireless utility (Zero Configuration Utility). If you are using another company’s utility, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.

If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility.

or

Right-click on the wireless computer icon in your system tray (lower-right corner next to the time). Select View Available Wireless Networks.

The utility will display any available wireless networks in your area. Click on a network (displayed using the SSID) and click the Connect button.

If you get a good signal but cannot access the Internet, check you TCP/

IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information.

D-Link DAP-1320 User Manual 47

Section 4 - Connecting to a Wireless Network

WPA/WPA2

It is recommended to enable WPA on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the WPA key being used.

1. Open the Windows® XP Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower-right corner of screen). Select View Available Wireless Networks.

2. Highlight the wireless network (SSID) you would like to connect to and click Connect.

D-Link DAP-1320 User Manual 48

Section 4 - Connecting to a Wireless Network

3. The Wireless Network Connection box will appear. Enter the WPA-PSK passphrase and click Connect.

It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WPA-PSK settings are correct. The

WPA-PSK passphrase must be exactly the same as on the wireless router.

D-Link DAP-1320 User Manual 49

Section 5 - Troubleshooting

Troubleshooting

This chapter provides solutions to problems that can occur during the installation and operation of the DAP-1320. Read the following descriptions if you are having problems.

1. Why can’t I access the web-based configuration utility?

When entering the IP address of the DAP-1320 (192.168.0.50 for example), you are not connecting to a website, nor do you have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must be on the same IP subnet to connect to the web-based utility.

• Make sure you have an updated Java-enabled web browser. We recommend the following:

- Microsoft Internet Explorer® 6 and higher

- Mozilla Firefox

- Google™ Chrome

- Apple Safari 4 and higher

• Verify physical connectivity by checking for solid link lights on the devices. If you do not get a solid link light, try using a different cable or connect to a different port on the device if possible. If the computer is turned off, the link light may not be on.

• Disable any Internet security software running on the computer. Software firewalls such as Zone Alarm, Black Ice, Sygate,

Norton Personal Firewall, and Windows

®

XP firewall may block access to the configuration pages. Check the help files included with your firewall software for more information on disabling or configuring it.

D-Link DAP-1320 User Manual 50

Section 5 - Troubleshooting

• Configure your Internet settings:

• Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults.

• Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button.

Make sure nothing is checked. Click OK.

• Go to the Advanced tab and click the Reset button to restore these settings to their defaults. Click OK three times.

• Close your web browser (if open) and open it.

• Access the Web Management. Open your web browser and enter the IP address of your DAP-1320 in the address bar. This should open the login page for your Web Management.

• If you still cannot access the configuration, unplug the device for 10 seconds and plug back in. Wait about 30 seconds and try accessing the configuration. If you have multiple computers, try connecting using a different computer.

2. What can I do if I forgot my password?

If you forgot your password, you must reset your DAP-1320 Unfortunately, this process will change all your settings back to the factory default settings.

To reset the DAP-1320, locate the reset button (hole) on the bottom of the unit. With the device powered on, use a paperclip to hold the button down for 10 seconds. Release the button and the device will reboot. Wait about 30 seconds to access the

DAP-1320. The default IP address is 192.168.0.50. When logging in, the username is admin and leave the password field empty.

Reset

D-Link DAP-1320 User Manual 51

Appendix A - Wireless Basics

Wireless Basics

D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers.

A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals instead of wires. Wireless LANs are used increasingly in both home and office environments, and public areas such as airports, coffee shops and universities. Innovative ways to utilize WLAN technology are helping people to work and communicate more efficiently.

Increased mobility and the absence of cabling and other fixed infrastructure have proven to be beneficial for many users.

Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop systems support the same protocols as Ethernet adapter cards.

Under many circumstances, it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order to use servers, printers or an Internet connection supplied through the wired LAN. A Wireless Router is a device used to provide this link.

D-Link DAP-1320 User Manual 52

Appendix A - Wireless Basics

What is Wireless?

Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or office network.

Why D-Link Wireless?

D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford. D-Link has all the products you need to build your network.

How does wireless work?

Wireless works similar to how cordless phone work, through radio signals to transmit data from one point A to point B. But wireless technology has restrictions as to how you can access the network. You must be within the wireless network range area to be able to connect your computer. There are two different types of wireless networks Wireless Local Area Network (WLAN), and Wireless Personal Area Network (WPAN).

Wireless Local Area Network (WLAN)

In a wireless local area network, a device called an Access Point (AP) connects computers to the network. The access point has a small antenna attached to it, which allows it to transmit data back and forth over radio signals. With an indoor access point, the signal can travel up to 300 feet. With an outdoor access point the signal can reach out up to 30 miles to serve places like manufacturing plants, industrial locations, college and high school campuses, airports, golf courses, and many other outdoor venues.

D-Link DAP-1320 User Manual 53

Appendix A - Wireless Basics

Wireless Personal Area Network (WPAN)

Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to

30 feet away.

Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as much power which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries.

Who uses wireless?

Wireless technology as become so popular in recent years that almost everyone is using it, whether it’s for home, office, business,

D-Link has a wireless solution for it.

Home

• Gives everyone at home broadband access

• Surf the web, check email, instant message, etc.

• Gets rid of the cables around the house

• Simple and easy to use

Small Office and Home Office

• Stay on top of everything at home as you would at office

• Remotely access your office network from home

• Share Internet connection and printer with multiple computers

• No need to dedicate office space

D-Link DAP-1320 User Manual 54

Appendix A - Wireless Basics

Where is wireless used?

Wireless technology is expanding everywhere not just at home or office. People like the freedom of mobility and it’s becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called “hotspots”.

Using a D-Link Cardbus Adapter with your laptop, you can access the hotspot to connect to Internet from remote locations like: Airports, Hotels, Coffee Shops, Libraries, Restaurants, and Convention Centers.

Wireless network is easy to setup, but if you’re installing it for the first time it could be quite a task not knowing where to start.

That’s why we’ve put together a few setup steps and tips to help you through the process of setting up a wireless network.

Tips

Here are a few things to keep in mind, when you install a wireless network.

Centralize your router or Access Point

Make sure you place the router/access point in a centralized location within your network for the best performance. Try to place the router/access point as high as possible in the room, so the signal gets dispersed throughout your home. If you have a two-story home, you may need a repeater to boost the signal to extend the range.

Eliminate Interference

Place home appliances such as cordless telephones, microwaves, and televisions as far away as possible from the router/access point. This would significantly reduce any interference that the appliances might cause since they operate on same frequency.

Security

Don’t let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA or WEP security feature on your router. Refer to product manual for detail information on how to set it up.

D-Link DAP-1320 User Manual 55

Appendix B - Networking Basics

Networking Basics

Check your IP address

After you install your new D-Link wireless adapter and have established a wireless connection, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e., router) automatically. To verify your IP address, please follow the steps below.

Windows® 8 Users

• Press the Windows key and R together. Type cmd in the box and click OK.

• At the prompt, type ipconfig and press Enter.

• This will display the IP address, subnet mask, and default gateway of your adapter.

Windows® 7/Vista® Users

• At the prompt, type ipconfig and press Enter.

• This will display the IP address, subnet mask, and default gateway of your adapter.

Windows® XP Users

• Click on Start > Run. In the run box type cmd and click OK.

• At the prompt, type ipconfig and press Enter.

• This will display the IP address, subnet mask, and the default gateway of your adapter.

If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your router. Some firewall software programs may block a DHCP request on newly installed adapters.

D-Link DAP-1320 User Manual 56

Appendix B - Networking Basics

Statically Assign an IP Address

If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below:

Windows® 8 Users

• Press the Windows key and then type IP. Click Settings on the right side and then click View Network Connections.

• Right-click on the adapter which represents your D-Link wireless network adapter.

• Highlight Internet Protocol Version 4 (TCP /IPv4) and click

Properties.

• Click Use the following IP address and enter an IP address that is on the same subnet as your network or LAN IP address on your router or network.

Example: If the router’s LAN IP address is 192.168.0.1, make your IP address 192.168.0.X where X is a number between 2 and 99. Make sure that the number you choose is not in use on the network.

• Set Default Gateway the same as the LAN IP address of your router or gateway.

• Set Primary DNS the same as the LAN IP address of your router or gateway.

• The Secondary DNS is optional (you may enter a DNS server from your ISP).

• Click OK to save your settings.

D-Link DAP-1320 User Manual 57

Appendix B - Networking Basics

Windows® 7/ Vista® Users

• Click on Start > Control Panel (make sure you are in Classic View). Double-click on the Network and Sharing Center icon. If you are using Windows Vista, click on Manage network connections along the left panel in the window. For

Windows® 7, click on Change adapter settings.

• Right-click on the Local Area Connection which represents your D-Link wireless network adapter which will be connected to your network.

• Highlight Internet Protocol Version 4 (TCP /IPv4) and click

Properties.

• Click Use the following IP address and enter an IP address that is on the same subnet as your network or LAN IP address on your router or network.

Example: If the router’s LAN IP address is 192.168.0.1, make your IP address 192.168.0.X where X is a number between 2 and 99. Make sure that the number you choose is not in use on the network.

• Set Default Gateway the same as the LAN IP address of your router or gateway.

• Set Primary DNS the same as the LAN IP address of your router or gateway.

• The Secondary DNS is optional (you may enter a DNS server from your ISP).

• Click OK to save your settings.

D-Link DAP-1320 User Manual 58

Appendix C - Technical Specifications

Technical Specifications

Standards

• IEEE 802.11n

• IEEE 802.11g

• 0% to 90% non-condensing

Wireless Frequency Range

• 2.4 GHz to 2.4835 GHz

Antennas

• Internal Antenna

Certifications

• Wi-Fi Certified

• FCC

Dimensions

• 2.11” x 1.65” x 1.89’’ (53.5 x 42 x 48mm)

Security

• Wi-Fi Protected Access (WPA/WPA2)

• WPS™ (PBC)

Weight

• 2.56 oz. (72.57g)

Warranty

• 1-Year Limited Warranty

Advanced Features

• Quick Router Setup app for iOS

Device Management

• Web UI

Diagnostic LEDs

• Power/ Status

Operating Temperature

• 32 to 104 ˚F (0 to 40 ˚C)

Operating Humidity

1 Maximum wireless signal rate derived from IEEE Standard 802.11g and 802.11n specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental factors will adversely affect wireless signal range.

2 Frequency Range varies depending on country’s regulation

D-Link DAP-1320 User Manual 59

Appendix D - Contacting Technical Support

Contacting Technical Support

U.S. and Canadian customers can contact D-Link technical support through our web site or by phone.

Before you contact technical support, please have the following ready:

• Model number of the product (e.g. DAP-1320)

• Hardware Revision (located on the label on the device (e.g. rev A2))

• Serial Number (s/n number located on the label on the device).

You can find software updates and user documentation on the D-Link website as well as frequently asked questions and answers to technical issues.

For customers within the United States:

Phone Support:

(877) 453-5465

Internet Support:

http://support.dlink.com

For customers within Canada:

Phone Support:

(800) 361-5265

Internet Support:

http://support.dlink.ca

D-Link DAP-1320 User Manual 60

Appendix F - Warranty

Warranty

Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty:

• Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and

• Only for products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.

Limited Warranty:

D-Link warrants that the hardware portion of the D-Link product described below (“Hardware”) will be free from material defects in workmanship and materials under normal use from the date of original retail purchase of the product, for the period set forth below (“Warranty Period”), except as otherwise stated herein.

• Hardware (excluding power supplies and fans): One (1) year

• Power supplies and fans: One (1) year

• Spare parts and spare kits: Ninety (90) days

The customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will be, at

D-Link’s option, to repair or replace the defective Hardware during the Warranty Period at no charge to the original owner or to refund the actual purchase price paid. Any repair or replacement will be rendered by D-Link at an Authorized D-Link Service Office. The replacement hardware need not be new or have an identical make, model or part. D-Link may, at its option, replace the defective Hardware or any part thereof with any reconditioned product that D-Link reasonably determines is substantially equivalent (or superior) in all material respects to the defective Hardware.

Repaired or replacement hardware will be warranted for the remainder of the original Warranty Period or ninety (90) days, whichever is longer, and is subject to the same limitations and exclusions. If a material defect is incapable of correction, or if D-Link determines that it is not practical to repair or replace the defective Hardware, the actual price paid by the original purchaser for the defective Hardware will be refunded by D-Link upon return to D-Link of the defective Hardware. All Hardware or part thereof that is replaced by D-Link, or for which the purchase price is refunded, shall become the property of D-Link upon replacement or refund.

D-Link DAP-1320 User Manual 61

Appendix F - Warranty

Limited Software Warranty:

D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specifications for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90) days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its documentation. D-Link further warrants that, during the Software Warranty Period, the magnetic media on which D-Link delivers the Software will be free of physical defects. The customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will be, at D-Link’s option, to replace the non-conforming Software (or defective media) with software that substantially conforms to D-Link’s functional specifications for the Software or to refund the portion of the actual purchase price paid that is attributable to the Software. Except as otherwise agreed by D-Link in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the license granted by D-Link for the Software. Replacement Software will be warranted for the remainder of the original Warranty Period and is subject to the same limitations and exclusions. If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to replace the non-conforming Software, the price paid by the original licensee for the non-conforming Software will be refunded by

D-Link; provided that the non-conforming Software (and all copies thereof) is first returned to D-Link. The license granted respecting any Software for which a refund is given automatically terminates.

Non-Applicability of Warranty:

The Limited Warranty provided hereunder for Hardware and Software portions of D-Link’s products will not be applied to and does not cover any refurbished product and any product purchased through the inventory clearance or liquidation sale or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case, the product is being sold “As-Is” without any warranty whatsoever including, without limitation, the Limited Warranty as described herein, notwithstanding anything stated herein to the contrary.

Submitting A Claim (USA):

The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expired and the product is within warranty, the customer shall submit a claim to D-Link as outlined below:

• The customer must submit with the product as part of the claim a written description of the Hardware defect or Software nonconformance in sufficient detail to allow DLink to confirm the same, along with proof of purchase of the product (such as a copy of the dated purchase invoice for the product) if the product is not registered.

• The customer must obtain a Case ID Number from D-Link Technical Support at 1-877-453-5465, who will attempt to assist the customer in resolving any suspected defects with the product. If the product is considered defective, the customer must obtain a

Return Material Authorization (“RMA”) number by completing the RMA form and entering the assigned Case ID Number at https:// rma.dlink.com/.

D-Link DAP-1320 User Manual 62

Appendix F - Warranty

• After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package.

Do not include any manuals or accessories in the shipping package. D-Link will only replace the defective portion of the product and will not ship back any accessories.

• The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products sent COD will either be rejected by D-Link or become the property of D-Link. Products shall be fully insured by the customer and shipped to D-Link Systems, Inc., 17595 Mt. Herrmann, Fountain Valley, CA 92708. D-Link will not be held responsible for any packages that are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via UPS Ground or any common carrier selected by D-Link. Return shipping charges shall be prepaid by D-Link if you use an address in the United States, otherwise we will ship the product to you freight collect. Expedited shipping is available upon request and provided shipping charges are prepaid by the customer. D-Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from the outside of the package. The product owner agrees to pay D-Link’s reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or non-conforming.

Submitting A Claim (Canada):

The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expired and the product is within warranty, the customer shall submit a claim to D-Link as outlined below:

• Customers need to provide their receipt (proof of purchase) even if the product is registered. Without a receipt, no warranty service will be done. The registration is not considered a proof of purchase.

• The customer must submit with the product as part of the claim a written description of the Hardware defect or Software nonconformance in sufficient detail to allow D-Link to confirm the same, along with proof of purchase of the product (such as a copy of the dated purchase invoice for the product) if the product is not registered.

• The customer must obtain a Case ID Number from D-Link Technical Support at 1-800-361-5265, who will attempt to assist the customer in resolving any suspected defects with the product. If the product is considered defective, the customer must obtain a Return Material

Authorization (“RMA”) number by completing the RMA form and entering the assigned Case ID Number at https://rma.dlink.ca/.

• After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. Do not include any manuals or accessories in the shipping package. D-Link will only replace the defective portion of the product and will not ship back any accessories.

D-Link DAP-1320 User Manual 63

Appendix F - Warranty

• The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products sent COD will be rejected by D-Link. Products shall be fully insured by the customer and shipped to D-Link Networks, Inc., 2525 Meadowvale Boulevard

Mississauga, Ontario, L5N 5S2 Canada. D-Link will not be held responsible for any packages that are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via Purolator Canada or any common carrier selected by D-Link. Return shipping charges shall be prepaid by D-Link if you use an address in Canada, otherwise we will ship the product to you freight collect. Expedited shipping is available upon request and provided shipping charges are prepaid by the customer. D-Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from the outside of the package. The product owner agrees to pay D-Link’s reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or non-conforming.

• RMA phone number: 1-800-361-5265 Hours of Operation: Monday-Friday, 9:00AM – 9:00PM EST

What Is Not Covered:

The Limited Warranty provided herein by D-Link does not cover:

Products that, in D-Link’s judgment, have been subjected to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation, lack of reasonable care, repair or service in any way that is not contemplated in the documentation for the product, or if the model or serial number has been altered, tampered with, defaced or removed; Initial installation, installation and removal of the product for repair, and shipping costs;

Operational adjustments covered in the operating manual for the product, and normal maintenance; Damage that occurs in shipment, due to act of God, failures due to power surge, and cosmetic damage; Any hardware, software, firmware or other products or services provided by anyone other than D-Link; and Products that have been purchased from inventory clearance or liquidation sales or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product.

While necessary maintenance or repairs on your Product can be performed by any company, we recommend that you use only an Authorized D-Link

Service Office. Improper or incorrectly performed maintenance or repair voids this Limited Warranty.

Disclaimer of Other Warranties:

EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE PRODUCT IS PROVIDED “AS-IS” WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER

INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.

IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY

SHALL BE LIMITED TO THE DURATION OF THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. EXCEPT AS EXPRESSLY COVERED UNDER THE

LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE

PURCHASER OF THE PRODUCT.

D-Link DAP-1320 User Manual 64

Appendix F - Warranty

Limitation of Liability:

TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL

OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT, SPECIAL,

INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK

STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINK’S PRODUCT

IS CONNECTED WITH, LOSS OF INFORMATION OR DATA CONTAINED IN, STORED ON, OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK

FOR WARRANTY SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF

THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF

THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NONCONFORMING PRODUCT. THE MAXIMUM

LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BY THE WARRANTY. THE FOREGOING

EXPRESS WRITTEN WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES, EXPRESS, IMPLIED

OR STATUTORY.

Governing Law:

This Limited Warranty shall be governed by the laws of the State of California. Some states do not allow exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This

Limited Warranty provides specific legal rights and you may also have other rights which vary from state to state.

Trademarks:

D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. Other trademarks or registered trademarks are the property of their respective owners.

Copyright Statement:

No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as stipulated by the

United States Copyright Act of 1976 and any amendments thereto. Contents are subject to change without prior notice.

Copyright ©2013 by D-Link Corporation/D-Link Systems, Inc. All rights reserved.

CE Mark Warning:

This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

D-Link DAP-1320 User Manual 65

Appendix F - Warranty

FCC Statement:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only.

IMPORTANT NOTICE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.to match the intended destination. The firmware setting is not accessible by the end user.

D-Link DAP-1320 User Manual 66

Appendix F - Warranty

Industry Canada statement:

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Declaration d’exposition aux radiations:

Cet equipement est conforme aux limites d’exposition aux rayonnements IC etablies pour un environnement non controle. Cet equipement doit etre installe et utilise avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.

D-Link DAP-1320 User Manual 67

Appendix G - Registration

Registration

Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights.

Version 1.1

August 27, 2013

D-Link DAP-1320 User Manual 68