SS10C-C50H

Indoor Ceiling Mount

SS10W-C50H

Outdoor Wall Mount

10x Mini PTZ Camera

Indoor Outdoor

USER MANUAL

FEATURES



1/4" Interline Transfer CCD, 500 TV Lines





10x Optical Zoom, 10x Digital Zoom (Max 100x Zoom)

F1.8, f=3.8~38mm focal length



0.7 lux (color) / 0.02 lux (B&W), 50 IRE



Mechanical IR Cut Filter (ICR), Day & Night Function



360° Endless Pan ; 180° Auto-flip Tilt ; 95° Normal Tilt



127 Presets ; RS-485 Communication, max 255 cameras



Pelco-D & Pelco-P Selectable protocols



Vector Drive Technology: Pan/Tilt motions are done at the shortest path



4 Alarm Inputs

–

SS10W-C50H



Fan & Heater

–

SS10W-C50H



12V DC

Copyright © 2012 by OKINA USA. All Rights Reserved.

** Replacing SS10C-C480DN

P-044_P-045

R201204-V27

Please read the Manual before attempting to use this product.

Specifications and appearance are subject to change without notice.

Disposal of Old Electrical & Electronic Equipment (Applicable in the

European Union and other European countries with separate collection systems).

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

CAUTION

1. Never point the camera toward the sun

Do not expose the lens directly to the sun or to strong light as this may damage the pick-up device.

2. Handle this camera with care

Avoid any shock or bumping of the camera. Improper handling could damage the camera.

3. Requires a proper operating environment

The ceiling mount camera is designed for indoor use. The allowable temperature range for operation is between 32°F ~ 104°F / 0



C ~ 40



C. The wall mount camera is designed for outdoor use. The allowable temperature range for operation is between

-22



F ~ 122



F / -30



C ~ 50



C.

2

4. Clean the front face or lens

It is recommended that the surface be cleaned every 3~6 months. Cleaning should be done by using a chamois, a very fine soft cloth, lens tissue, or cotton tipped applicator and ethanol to carefully remove any fingerprint or dust.

5. Check the power source voltage

The power source voltage should be within the specified range. (Camera must meet the specifications). Camera must be connected to a surge protector at all times.

6. Objects and liquid entry

Never push objects of any kind into this camera as this may touch dangerous voltage points of short out parts that could result in a fire or electric shock. Never spill any kind of liquid on the video product.

7. Servicing

Do not attempt to service this video product by yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all service to qualified servicing personnel.

8. Damage requiring service

Unplug this video product from the wall outlet and refer service to qualified servicing personnel under the following conditions: a. When the power supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the video product. c. If the video product has been exposed to rain or water. d. If the video product has been dropped or the cabinet has been damaged. e. When the video product exhibits a distinct change in performance.

LIMITED WARRANTY

OKINA USA products are covered under warranty for one year from the date of purchase. The warranty will automatically be voided if any of the following occurs:

1. Camera sticker is removed

If the camera sticker is removed, we will not be able to confirm any information regarding when and where the product was purchased. We have no other way to verify the purchase record without the serial number on the camera sticker; therefore, it should not be removed.

2. Camera is modified in any way

If the camera is scratched, damaged, or modified in a manner not described in this manual, the warranty will be voided immediately. It is the customer’s responsibility to keep the camera in good condition.

3. Video or power cable is cut

The video cable and the power cable should not be tampered with. Cutting or modifying of the cables will result in termination of the warranty.

3

INDEX

FEATUERS ……………………………………………………………………………………. 1

CAUTIONS ………………………………………………………………………………….. 2-3

LIMITED WARRANTY ……………………………………………………………………….. 3

PACKAGE CONTENTS ……………………………………………………………………… 5

DIMENSIONS ……………………………………………………………………..………... 5-6

DIP SWITCH SETTING ……………………………………………………………………. 7-8

APPLICATION DIAGRAM ………………………………………………………..…………. 8

INSTALLAT

ION …………………………………………………………………………… 9-10

OPERATION ……………………………………………………………………………….10-14

PRESET AND PATTERN FUNCTION PRE-

CHECK …………………….……. 10

STARTING OSD MENU …………………………………………………….……. 11

RESERVED PRE

SET …………………………………………………………….. 11

PRESET …………………………………………………………………………..... 11

SWING ……………………………………………………………………………… 12

PATTERN

……………………………………………………………………... 12-13

GROUP …………………………………………………………………………….. 13

OTHER FUNCT

IONS ………………………………………………………………14

HOW TO USE OSD MENU ………………………………………………………….…. 15-31

OSD DISPLAY OF MAIN SCR

EEN …………………………………………...... 15

GENERAL RULES OF KEY OPERATION

FOR MENU ………………………. 16

MAIN MENU

……………………………………………………………………….. 16

DISPLAY SETUP …………………………………………………………..…. 16-17

PRIVACY ZONE MASK SETUP ………………………………………..…… 17-18

CAMERA SETUP ……………………………………………………….…….. 19-20

MOTION SETUP ………………………………………………………….….. 21-23

PRESET SET

UP ……………………………………………………………... 23-25

SWING SETUP ………………………………………………………………. 25-26

PATTERN SETUP …………………………………………………….……… 26-27

GROUP SETUP ………………………………………………….…………… 27-29

SYSTEM INITIALIZE ……………………………………………..………….. 30-31

SPECIFICATION ……………………………………………………………..…………….. 32

4

PACKAGE CONTENTS



One (1) 10x Mini PTZ Dome Camera



One (1) Mounting Base



Three (3) Mounting Base Screws



Three (3) Thread Connector Screws



One (1) Thread Connector



One (1) User Manual

*Ceiling bracket is standard for mini PTZ Dome.

* Arm Type Wall mount bracket is standard for Outdoor PTZ Dome.

Options for SS10C-C50H:

Pendant Pole Bracket

MB-CP10C

L Type Wall Mount Bracket

MB-CW1C

Arm Type Wall Mount Bracket

MB-CWA10C

For any returns, please include all components listed above with original packaging in

Resalable Condition. Absolutely No Returns will be accepted if any component is missing and/or damaged.

5

DIMENSIONS

Indoor Ceiling Mount

Ø 5.04” / 128mm

Outdoor Arm Type Wall Mount

Ø 4.2” / 107.7mm

Ø 5” / 127mm

With Pendant Pole Mount With L Type Wall Mount

6

DIP SWITCH SETTING

Before you install the camera, you should set the DIP switches to configure the camera ID, communication protocol.

Camera ID Setup



ID number of camera is set using binary number. The example is shown below.

Pin

ID Value

Ex) ID=5

Ex) ID=10

1

1

Off

Off

2

2

Off

Off

3

4

Off

Off

4

8

Off

Off

5

16

Off

Off

6

32

Off

Off

7 8

64 128

Off

Off

Off

Off



The range of ID is 1~255. Do not use 0 as Camera ID. Factory default is 1.



If you want to control a certain camera, you must match the camera ID with the Cam ID setting of DVR or Controller

Communication Protocol Setup



Select the appropriate Protocol with DIP switch combination.

7

P0

(Pin 1)

OFF

ON

OFF

ON

Switch State

P1

(Pin 2)

OFF

OFF

ON

ON

Protocol

PELCO-D, 2400 bps

PELCO-D, 9600 bps

PELCO-P, 4800 bps

PELCO-P, 9600 bps



If you want to control using DVR or P/T controller, the protocol must be identical to the camera.



If you change the camera protocol by changing the DIP S/W, the change will be effective after you reboot the camera.



Factory default is Pelco-D, 2400 bps



Pin 3 and Pin 4 is only for su pplier’s use. Do not change the original

settings for these two pins, otherwise, the camera may not operate normally. o

Pin 3: PAL/NTSC system selection of Camera. DO NOT CHANGE

THIS PIN.

APPLICATION DIAGRAM

Monitor

Cabling Terminal Block

8

INSTALLATION

Power Connection

Please, check the voltage and current capacity of rated power carefully. Rated power is indicated in the back of main unit.

Rated Power Input Voltage Range Current Consumption

12V DC

RS-485 Communication

11V~18V DC 0.8 A

For PTZ control, connect the keyboard and DVR. To control multiple cameras at the same time, RS-485 communication lines of them is connected in parallel as shown below.

Video Connection

Connect with BNC coaxial cable.

Alarm input Connection (For Outdoor PTZ, SS10W-C50H)

Sensor Input

9

Before connecting sensors, check driving voltage and output signal type of the sensor. Since output signal types of the sensors are divided into open collector and voltage output type in general, the cabling must be done properly after considering these typed.

Signal Description

IN COM+

IN1-, IN2-, IN3-, IN4-

Connect (+) cable of electric power source for sensors to this port as shown in the circuit above.

Connect output of sensors for each other port as shown in the circuit above.

If you want to use Alarm Input, the types of sensor must be selected in OSD menu.

The sensor types are Normal Open and Normal. It sensor type is not selected properly, the alarm can be activated reversely.

Normal Open

Normal Close

Output voltage is high state when sensor is activated

Output voltage is high state when sensor is NOT activated

OPERATION



Before power is applied, please check the cables carefully.



The camera ID of the controller must be identical to that of the target camera.

The camera ID can be checked by reading DIP switch of the camera.



If your controller supports multi-protocols, the protocol must be changed to match to that of the camera.



If you changed camera protocol by changing DIP switch, the change will be effective after you reboot the camera.



Since the operation method can be different for each controller available, refer to the manual for your controller if camera cannot be controlled properly. The operation of this manual is based on the standard Pelco Controller.

PRESET AND PATTERN FUNCTION PRE-CHECK



Check how to operate preset and pattern function with controller or DVR in advance to fully operate camera function when using controller or DVR.



Refer to the following table when using standard Pelco protocol controller.

<Go Preset>

<Set Preset>

<Run Pattern>

<Set Pattern>

Press [Call] input [Preset number] and press [Enter]

Press [Preset] input [Preset number and press [Enter]

Press [Call] input [Preset number and press [Enter]

Refer to the pattern setup on page 26



If controller or DVR has no pattern button or function, use shortcut keys with preset numbers. For more information, refer to “Reserved Preset” in this manual

10

STARTING OSD MENU

Function Using the OSD menu, Preset, Pattern, Swing, Group and Alarm Input function can be configured for each application.

Enter Menu Press <Call> + Preset Number [95] + <Enter>

RESERVED PRESET

Description

Function

Some Preset numbers are reserved to special functions.

<Call> [95] <Enter> : Enters into OSD menu

<Call>[131~134]<Enter> : Runs Pattern Function 1~4

<Call>[141~148]<Enter> : Runs Swing Function 1~8

<Call>[151~158]<Enter> : Runs Group Function 1~8

<Call>[161~162]<Enter> : Sets Relay Output 1~2 to OFF

<Shot>[161~162] <Enter> : Sets Relay Output 1~2 to ON

<Call>[170]<Enter> :

<Call>[171]<Enter> :

Sets Camera BLC Mode to OFF

Sets Camera BLC Mode to ON

<Call>[174]<Enter> :

<Call>[175]<Enter> :

<Call>[176]<Enter> :

<Call>[177]<Enter> :

<Call>[178]<Enter> :

<Call>[179]<Enter> :

<Call>[190]<Enter> :

<Call>[191]<Enter> :

Sets Camera Focus Mode to AUTO

Sets Camera Focus Mode to Manual

Sets Camera Focus Mode to SEMI-AUTO

Sets Day&Night Mode to AUTO

Sets Day&Night Mode to NIGHT

Sets Day&Night Mode to DAY

Sets OSD Display Mode to AUTO

(Except Privacy Mask)

Sets OSD Display Mode to OFF

<Call>[192]<Enter> :

<Call>[193]<Enter> :

<Call>[194]<Enter> :

(Except Privacy Mask)

Sets OSD Display Mode to ON

(Except Privacy Mask)

Sets all Privacy Mask Display to OFF

Sets all Privacy Mask Display to ON

PRESET

Function Max 127 positions can be stored as Preset position. The Preset number can be assigned from 1~128, but 95 is reserved for starting

OSD menu. Camera characteristics (i.e. White Balance, Auto

Exposure) can be set up independently for each preset. Label should be blank and ”Camera Adjust” should be set to ”GLOBAL” as default.

All characteristics can be set up in OSD menu

Set Preset <Preset>[1~128 ] <Enter> (Except [95])

Run Preset <Call>[1~128 ] <Enter> (Except [95]) To delete Preset, use OSD menu.

Delete Preset <Dome Camera Setup>→<Preset Setup>→<Ctrl Preset>

11

SWING

Function By using Swing function, you can make camera to move between 2

Preset positions repeatedly. When swing function runs, camera moves from the preset assigned as the 1

2 nd st

point to the preset assigned as the

point in CW (Clockwise) direction. Then camera moves from the preset assigned as the 2 nd

point to the preset assigned as the 1st point in CCW (Counterclockwise) direction.

In case that the preset assigned as the 1 assigned as the 2 nd st

point is same as the preset

point, camera turns on its axis by 360° in CW

(Clockwise) direction and then it turns on its axis by 360° in CCW

(Counterclockwise) direction. Speed can be set up from 1° /sec to

180° /sec.

Set Preset

Run Swing

To set Swing, use OSD menu.

<Dome Camera Setup>  <Swing Setup>

E.g.: Run the first swing <Call>[141]<Enter>

E.g.: Run the second swing <Call>[142]<Enter>

Delete Swing To delete Swing, use OSD menu.

<Dome Camera Setup>→<Swing Setup>→<Clear Swing>

PATTERN

Function Pattern Function is that a camera memorizes the path (mostly curve path) by joystick of controller for assigned time and revives the path exactly as it memorized. 4 Patterns are available and Maximum 1200 communication commands can be stored in a pattern.

Setup Pattern <Dome Camera Setup>→<Pattern Setup>→<Edit Pattern>



Pattern editing screen is displayed as bellow.

EDIT PATTERN1

[NEAR: SAVE / FAR: DELETE]

0 / 0 / X1 / N

12



Movement by Joystick and preset movement can be memorized in a pattern.



The rest memory size is displayed in progress bar.



To save the recording, press NEAR key and to cancel, press FAR key.

Method 2)

OSD Using OSD Menu: See the section “How to use OSD

Menu".

Run Pattern E.g.) Run Pattern 1: <Call>[131]<Enter>

E.g.) Run Pattern 2: <Call>[132]<Enter>

Delete Pattern Use OSD menu to delete Pattern

<Dome Camera Setup>→<Pattern Setup>→<Ctrl Pattern>

GROUP

Function The group function allows running sequence of Presets, Pattern and/or Swings Max 8 group can be stored. Each group can have max

20 action entities which can be preset, pattern or swing Preset speed can be set up and the repeat number of Pattern & Swing can be set up in Group setup. Dwell time between actions can be set up also.

Set Group

Run Group

Use OSD Menu to create a Group

Ex) Run Group 1: <Call>[151]<Enter>

Ex) Run Group 2: <Call>[152]<Enter>

Delete Group Use OSD Menu to delete

<Dome Camera Setup>→<Group Setup>→<Clear Group>

13

OTHER FUNCTIONS

Power Up Action This function enables to resume the last action executed before power down. Most of actions such as Preset, Pattern, Swing and Group are available for this function but jog actions are not available to resume.

Auto Flip In case that tilt angle arrives at the top of tilt orbit (90º), zoom module camera keep moving to opposite tilt direction (180º) to keep tracing targets. As soon as zoom module camera passes through the top of tilt direction (90º), images should be reversed automatically and F appears in screen. If this function is set to OFF, tilt movement range is

0~95º.

Parking Action This function enables to locate the camera to specific position automatically if operator doesn't operate the controller for a while. The

Park Time can be defined as an interval from 1 minute to 4 hours.

Privacy Zone

Mask

To protect privacy, MAX. 4 Privacy Masks can be created on the arbitrary position to hide objects such as windows, shops or private house. With Spherical Coordinates system, powerful Privacy Zone

Mask function is possible.

Global/Local WB (White Balance) and AE (Auto Exposure) can be set up

Image Setup independently for each preset. There are 2 modes, "Global" mode ＆

"Local" mode. The Global mode means that WB or AE can be set up totally and simultaneously for all presets in "ZOOM CAMERA SETUP" menu. The Local mode means that WB or AE can be set up independently or separately for each preset in each preset setup menu. Each Local WB/AE value should activate correspondingly when camera arrives at each preset location. During jog operation, Global

WB/AE value should be applied. All Local WB/AE value does not change although Global WB/AE value changes.

Semi-Auto

Focus

This mode exchanges focus mode automatically between Manual

Focus mode and Auto Focus mode by operation. Manual Focus mode activates in preset operation and Auto Focus mode activates during jog operation With Manual mode at presets, Focus data is memorized in each preset in advance and camera calls focus data in correspondence with presets as soon as camera arrives at a preset. It should shorten time to get focuses Focus mode changes to Auto

Focus mode automatically when jog operation starts.

14

HOW TO USE OSD MENU

OSD DISPLAY OF MAIN SCREEN

P/T/Z Info

Camera ID

Action Title

Preset Label

Alarm Input

Current Pan/Tilt angle in degree, zoom magnification and a compass direction.

Current Camera ID (address)

Follovangs are possible Action-Titles and their meaning. "SET

PRESET ×××"

When Preset××× is stored "PRESET×××" When camera reach to

Preset ×××

"PATTERN ×" When Pattern × is in action

“ SWG×/PRESET×××” When Swing × is in action

"UNDEFINE D" When undefined function is called to run

The label stored for specific Preset.

This information shows current state of Alarm Input. If an Input point is

ON state it will show a number corresponding to each point If an Input point is OFF state, ' - ' will be displayed

Ex) Point 2&3 of inputs are ON, OSD will show as below

Image Flip Shows that images are currently reversed by Auto Flip Function.

15

GENERAL RULES OF KEY OPERATION FOR MENU



The menu items surrounded with ( ) always has its sub menu.



For all menu level, to go into sub menu, press NEAR key.



To go to up-one-level menu, press FAR key.



To move from items to item in the menu, use joystick in the Up/Down or

Left/Right. To change a value of an item, use Up/Down of the joystick in the controller.



Press NEAR key to save values and Press FAR key to cancel Values.

MAIN MENU

SPEED DOME CAMERA SYSTEM

INFORMATION

 <DISPLAY SETUP>

<DOME CAMERA SETUP>

<SYSTEM INITIALIZE>

EXIT

System Info Displays system information and configuration.

Display Setup Enable/Disable of OSD display on Main Screen

Dome Camera Configure various functions of this camera.

Setup

System Initialize Initializes system configuration and sets all data to factory default configuration

DISPLAY SETUP

This menu defines Enable/Disable of OSD display on Main Screen.

If an item is set to be AUTO, the item is displayed only when the value of it is changed.

DISPLAY SETUP

CAMERA ID

 PTZ INFORMATION

ACTION TITLE

PRESET LABEL

ALARM INPUT

AUTO

AUTO

<SET NORTH DIRECTION>

<PRIVACY ZONE>

BACK

EXIT

ON

AUTO

AUTO

16

Camera ID

PTZ Info

Action Title

Preset Label

Alarm Input

[ON/OFF]

[ON/OFF/AUTO]

[ON/OFF/Auto]

[ON/OFF/AUTO]

[ON/OFF/AUTO]

Compass Direction Setup

SET NORTH DIRECTION

MOVE TO TARGET POSITION

[NEAR:SAVE / FAR: CANCEL]

Set North to assign compass direction as criteria. Move camera and press NEAR button to save.

PRIVACY ZONE MASK SETUP

<Display Setup>→<Privacy Zone>

Select area in image to mask

PRIVACY ZONE

MASK NO



DISPLAY

CLEAR MASK

<EDIT MASK>

BACK

EXIT

1

UNDEFINED

OFF

CANCEL

Mask No. Select Mask number. If the selected mask has already data, camera moves as it was set. Otherwise, “UNDEFINED” will be displayed under

“Mask No”.

17

Display

Clear Mask

[ON/OFE]

Sets if camera makes mask shows or not on images

[CANCEL/OK]

Deletes data in the selected Mask No.

Privacy Zone Area Setup

<Display Setup>→<Privacy Zone>→<Edit Mask>

Move camera to area to mask. Then the menu to adjust mask size will be displayed.

EDIT MASK 1

MOVE TO TARGET POSITION

[NEAR:SELECT / FAR: CANCEL]

Privacy Zone Size Adjustment

Adjust mask size. Use joystick or arrow buttons to adjust mask size.

EDIT MASK 1

[ : ADJUST MASK WIDTH]

[ : ADJUST MASK HEIGHT]

[NEAR: SAVE / FAR: CANCEL]

 (Left/Right) Adjusts mask width.

 (Up/Down) Adjusts mask height.

18

CAMERA SETUP

<Dome Camera Setup>→<Camera Setup>

Setup the general functions of zoom camera module.

ZOOM CAMERA SETUP

 FOCUS MODE

DIGITAL ZOOM

SEMIAUTO

ON

LINE LOCK OFF

<WHITE BALANCE SETUP>

<AUTO EXPOSURE SETUP>

BACK

EXIT

Focus Mode [AUTO/MANUAL/SEMIAUTO]

Sets camera focus mode.

SEMIAUTO Mode

This mode exchanges focus mode automatically between Manual

Focus mode and Auto Focus mode Manual Focus mode activates in preset operation and Auto Focus mode activates when jog operation starts. With Manual mode at presets, Focus data is memorized in each preset in advance and camera calls focus data in correspondence with presets as soon as camera arrives at a preset.

Digital Zoom [ON/OFF]

Sets digital zoom function to ON/OFF. If this is set to OFF, optical zoom function runs but zoom function stops at the end of optical zoom magnification.

Line Lock [ON/OFF]

If Line lock sync is ON, video signal is synchronized with AC power.

Video can be fluctuated after setting is changed.

White Balance Setup

<Dome Camera Setup>→<Camera Setup>→<White Balance Setup>

WB SETUP - GLOBAL

 WB MODE

RED ADJUST

BLUE ADJUST

BACK

EXIT

AUTO

----

----

WB Mode

Red Adjust

Blue Adjust

[AUTO/MANUAL]

In Manual mode, Red and Blue level can be set up manually.

[10~60]

[10~60]

19

Auto Exposure Setup

<Dome Camera Setup>→<Camera Setup>→<Auto Exposure Setup>

AE SETUP - GLOBAL

 BACKLIGHT

DAY/NIGHT

BRIGHTNESS

IRIS

SHUTTER

AGC

SSNR

SENS-UP

BACK

EXIT

OFF

AUTO1

25

AUTO

ESC

NORMAL

MIDDLE

<AUTO>

Backlight

Day/Night

[ON/OFF]

Sets Backlight Compensation

Brightness

IRIS fixed and Iris has lower priority in adjusting AE, in comparison with others.

Shutter Speed [ESC/A. Flicker/Manual (x 128~1/120000 sec )]

If Iris is set to Manual and Shutter Speed is set to ESC, Shutter Speed should have highest priority. If Shutter Speed is set to A. Flicker, to remove Flicker, Shutter Speed should be set to 1/100 secretary for

NTSC and 1/120 for PAL.

AGC

[0~100]

Adjusts brightness of images. Iris, Shutter Speed and Gain are adjusted automatically in correspondence with this value

[AUTO/MANUAL(0~100)]

If Iris is set to Auto Iris should have highest priority in adjusting AE and

Shutter Speed should be fixed. If Iris is set to Manual, Iris should be

[OFF/NORMAL/HIGH]

Enhances image brightness automatically in case that luminance level of image signal is too low.

SSNR

[AUTO1/AUTO2 DAY/NIGHT]

AUTO1 exchanges Day/Night mode faster than

AUTO2.

[OFF/LOW/MIDDLE/HIGH]

Enhances images by deducting noises when gain level of images is too high.

Sens-Up [AUTO(2~128)/OFF]

Activates Slow Shutter function when luminance of Image (signal) is too dark. It is possible to set up the maximum number of frames piled up one on another by Slow Shutter function

20

MOTION SETUP

<Dome Camera Setup>→<Motion Setup>

Setup the general functions of Pan/Tilt motions.

MOTION SETUP

MOTION LOCK

 PWR UP ACTION

OFF

ON

AUTO FLIP

JOG MAX SPEED

JOG DIRECTION

FRZ IN PRESET

ON

120



/SEC

INVERSE

OFF

<PARKING ACTION SETUP>

<ALARM INPUT SETUP>

BACK

EXIT

Motion Lock [ON/OFF]

Group. It is possible only to run those functions. To set up and delete those functions, enter into OSD menu.

Power Up Action [ON/OFF]

Refer to “Other Functions” section on page 14.

Auto Flip [ON/OFF]

Refer to “Other Functions” section on page 14.

Jog Max Speed [1º /sec~360º /sec]

Sets maximum jog speed. Jog speed is inversely proportional to zoom magnification. As zoom magnification goes up, pan/tilt speed goes down.

Jog Direction [INVERSE/NORMAL]

If you set this to 'Inverse', the view in the screen is moving same direction with jog tilting. If 'Normal' is selected, the view in the screen is moving reversely.

Freeze In Preset [ON/OFF]

At start point of preset movement, camera starts freezing the image of start point. Camera keeps displaying the image of start point during preset movement and does not display the images which camera gets during preset movement. As soon as camera stops at preset end point, camera starts displaying live images which it gets at preset end point.

This function availability should be different by models.

21

Parking Action Setup

<Dome Camera Setup>→<Motion Setup>→<Parking Action Setup>

If Park Enable is set to ON, camera runs assigned function automatically if there is no

PTZ command during assigned ''Wait Time''.

PARKING ACTION SETUP

PARK ENABLE

 WATI TIME

OFF

00:10:00

HOME PARK ACTION

BACK

EXIT

Park Enable

Wait Time

[ON/OFF]

[1 minute ~ 4 hours]

The time is displayed with "hh:mm:ss" format and you can change this by 1 min unit.

Park Action [HOME/PRESET/PATTERN/SWING/GROUP]

HOME

Camera moves to home position if there is no PTZ command during assigned "Wait Time".

Alarm Input Setup (For Outdoor PTZ, SS10W-C50H)

<Dome Camera Setup>→<Motion Setup>→<Alarm Input Setup>

Match the Alarm sensor input to one of Preset positions. If an external sensor is activated, camera will move to corresponding preset position when this item is predefined.

ALARM INPUT SETUP

ALARM1 TYPE

ALARM2 TYPE

ALARM3 TYPE

ALARM4 TYPE

ALARM1 ACT

ALARM2 ACT

ALARM3 ACT

ALARM4 ACT

BACK

EXIT

N.OPEN

N.OPEN

N. OPEN

N.OPEN

NOT USED

NOT USED

NOT USED

NOT USED

22

Alarm x Type [Normal OPEN/Normal CLOSE]

Sets sensor input type.

Alarm x Action [Not USED/PRESET1~128]

Assign counteraction preset position to each alarm input.

PRESET SETUP

<Dome Camera Setup>→<Preset Setup>

PRESET SETUP

 PRESET NO

CLR PRESET

<EDIT SCENE>

<EDIT LABEL>

CAM ADJUST

LABEL 123

GLOBAL

BACK

EXIT

Preset Number [1~128] (Except [95])

If a selected preset is already defined, camera moves to pre- defined position and preset characteristics such as Label and Relay Outputs show on monitor. If a selected preset is not defined. "UNDEFINED" shows on monitor.

Clear Preset

Edit Preset

Scene

[CANCEL/OK]

Delete current Preset data.

Redefine current Preset scene position (i.e. PTZ)

Edit Preset

Label

CAM Adjust

1

CANCEL

Edits Label to show on monitor when preset runs

MAX. 10 alphabets are allowed

[GLOBAL/LOCAL]

WB (White Balance) and AE (Auto Exposure) can be set up independently for each preset. There are 2 modes, "Global" mode &

"Local" mode. The Global mode means that WB or AE can be set up totally and simultaneously for all presets in "Z00M CAMERA SETUP" menu. The Local mode means that WB or AE can be set up independently or separately for each preset in each preset setup menu. Each Local WB/AE value should activate correspondingly when camera arrives at each preset location. During jog operation, Global

WB/AE value should be applied. All Local WB/AE value should not change although Global WB/AE value changes. If “Local” is selected,

Menu to set WB/AE shows on Monitor.

23

Edit Preset Scene

<Dome Camera Setup>→<Preset Setup>→<Edit Scene>

EDIT SCENE

– PRESET1

MOVE TO TARGET POSITION

[NEAR: SAVE / FAR: CANCEL]

1. Using Joystick, move camera angle to desired position.

2. By pressing NEAR key, save current PTZ data.

3. Press FAR key to cancel.

Edit Preset Label

<Dome Camera Setup>→<Preset Setup>→<Edit Label>

EDIT LABEL

– PRESET1

[ ]

- - - - - - - - - - - - - -

1 2 3 4 5 6 7 8 9 0

A B C D E F G H I

J K L M N O P Q R

S T U V W X Y Z a b c d e f g h I j k l m n o p q r s t u v w

OK

CANCEL x y z < > - / . 

1. Edits label to show on monitor when camera arrives at presets. In Edit Label

BACK

EXIT menu, a reverse rectangular is cursor As soon as finishing selecting alphabet, cursor moves to the next digit

2. Using Left/Right/Up/Down of joystick, move to an appropriate character from the Character set. To choose that character, press the NEAR key.

If you want to use blank, choose Space character (" "). If you want to delete a character before, use back space character ("").

24

3. If you complete the Label editing, move cursor to "OK" and press NEAR key to save completed label. To abort current change, move cursor to "Cancel" and press NEAR key.

SWING SETUP

<Dome Camera Setup>→<Swing Setup>

SWING SETUP

 SWING NO

1ST POS

2ND POS

SWING SPEED

CLEAR SWING

BACK

EXIT

1

NOT USED

NOT USED

30



/SEC

CANCEL

Swing Number [1~8]

Selects Swing number to edit. If a selected Swing has not defined,

"NOT USED" is displayed in 1 st

position and 2 nd

position.

1 st

2 nd

Position

Position

[PRESET 1~128] (Except [95])

Set up the 2 nd

position for Swing function. If a selected preset is not defined, "UNDEFINED" will be displayed as shown below:

When swing function runs, camera moves from the preset assigned as the 1 st

point to the preset assigned as the 2 nd

point in CW

(Clockwise) direction. Then camera moves from the preset assigned as the 2 nd

point to the preset assigned as the 1 st

point in CCW

(Counterclockwise) direction. In case that the preset assigned as the

1 st

point is same as the preset assigned as the 2 nd

point camera turns on its axis by 360º in CW direction and then it turns on its axis by 360º in CCW direction.

25

Swing Speed [1



/sec~180



/sec]

Sets Swing speed from 1



/sec to 180



/sec.

Clear Swing [CANCEL/OK]

Deletes current Swing data.

PATTERN SETUP

<Dome Camera Setup>→<Pattern Setup>

PATTERN SETUP

 PATTERN NO

CLR PATTERN

<EDIT PATTER>

BACK

EXIT

1

UNDEFINED

CANCEL

Pattern Number [1~4]

Selects Pattern number to edit. If a selected pattern number is not defined, “UNDEFINED” will be displayed under selected pattern number.

Clear Pattern [CANCEL/OK]

Deletes data in current pattern.

Starts editing pattern. Edit Pattern

Edit Pattern

<Dome Camera Setup>→<Pattern Setup>→<Edit Pattern>

1. By using Joystick, move to start position with appropriate zoom. To start pattern recording, press NEAR key. To exit this menu, press FAR key.

EDIT PATTERN1

MOVE TO START POSITION

[NEAR: START / FAR: CANCEL]

26

2. Move camera with joystick or run preset function to memorize the path

(mostly curve path) in a selected pattern. The total memory size and the rest memory size is displayed m the form of bar. Maximum 1200 communication commands can be stored in a pattern.

EDIT PATTERN1

MOVE TO START POSITION

[NEAR: SAVE / FAR: DELETE]

X 0 / 0 / 1 / N

3. To save data and exit, press NEAR key .To cancel recording and delete recording data, press FAR key.

GROUP SETUP

<Dome Camera Setup>→<Group Setup>

GROUP SETUP

 GROUP NO

CLEAR GROUP

<EDIT GROUP>

BACK

EXIT

1

UNDEFINED

CANCEL

Group Number [1~8]

Selects group number to edit. If a selected group number is not defined, “UNDEFINED” will be displayed under selected group number.

Clear Group

Edit Group

[CANCEL/OK]

Deletes data in current Group.

Starts editing Group.

27

Edit Group

<Dome Camera Setup>→<Group Setup>→<Edit Group>

1. Press Near key in "NO" list to start Group setup.

EDIT GROUP 1

 NO. ACTION ### DWELL OPT

1 NONE

2 NONE

3

4

5

NONE

NONE

NONE

SAVE

CANCEL [NEAR:EDIT]

2. Note that MAX.20 Functions are allowed in a Group. Move cursor up/down and press Near key to set up.

EDIT GROUP 1

NO. ACTION ### DWELL OPT



1 NONE

2 NONE

3 NONE

4

5

NONE

NONE

SAVE [NEAR:EDIT ACT]

CANCEL [FAR:EDIT:END]

3. Setup Action, Dwell time and Option. Note that selected item is displayed in reverse. Move cursor Left/Right to select items and move cursor Up/Down to change each value.

EDIT GROUP 1

NO. ACTION ### DWELL OPT

1 NONE

2 NONE

3

4

5

NONE

NONE

NONE

SAVE [: MOVE CURSER]

CANCEL [ : CHANGE VAL]

28

Action ###

DWELL

OPT

[NONE / PRESET / SWING / PATTERN]

[0 seconds~4 minutes]

Option

It should be preset speed when preset is set in Action and the number of repeat when Pattern or Swing is selected in

Action.

4. Setup items such as Action, ###, Dwell and OPT.

EDIT GROUP 1

NO. ACTION ### DWELL OPT

1 PRESET 1 00:03 360

2 NONE

3

4

5

NONE

NONE

NONE

SAVE [: MOVE CURSER]

CANCEL [ : CHANGE VAL]

5. After finishing setting up an Action, Press Near key to one-upper-level. Move cursor Up/ Down to select Action number and repeat Step 1~4 to edit selected

Group.

EDIT GROUP 1

NO. ACTION ### DWELL OPT



1 NONE 1 00:03 360

2 NONE

3

4

5

NONE

NONE

NONE

SAVE [NEAR:EDIT ACT]

CANCEL [FAR:EDIT END]

6. After finishing setting up all Action, Press FAR key to exit. Then cursor should be moved to" SAVE ", Press Near key to save data.

EDIT GROUP 1

NO. ACTION ### DWELL OPT

1 NONE 1 00:03 360

2 NONE

3 NONE

4

5

NONE

NONE



SAVE

CANCEL

[NEAR:EDIT ACT]

[FAR:EDIT END]

29

SYSTEM INITIALZE

SYSTEM INITIALIZE

N O

N O

N O

CLEAR ALL DATA



CLR DISPLAY SET



CLR CAMERA SET



CLR MOTION SET



CLR EDIT DATA

REBOOT CAMERA

N O

N O

N O

N O REBOOT SYSTEM

SAVE

CANCEL

Clear All Data Deletes all configuration data such as display camera, motion set, and so on.

Clear Display Initializes Display Configuration

Set

Clear Camera Initializes Camera Configuration

Set

Clear Motion Initializes Motion Configuration

Set

Clear Edit Date Deletes preset date, swing data, pattern data and group data

Reboot Camera Reboots Zoom camera module

Reboot System Reboots speed dome camera

Initial Configuration Table

Display Configuration

Camera ID

PTZ Information

Action Title

Preset Label

Alarm Input

North Direction

Privacy Zone

ON

AUTO

AUTO

AUTO

AUTO

Pan 0



Undefined

30

Camera Configuration

Focus Mode Focus Mode

Digital Zoom

Line Lock

White Balance

Digital

Zoom

Line Lock

White

Balance

Backlight

Day & Night

Brightness

Iris

Shutter

AGC

SSNR

SENS-UP

Backlight

Day & Night

Brightness

Iris

Shutter

AGC

SSNR

SENS-UP

Motion Configuration

Motion Lock

Power Up Action

Auto Flip

Jog Max Speed

Jog Direction

Freeze In Preset

Park Action

OFF

ON

ON

120



/sec

INVERSE

OFF

OFF

Alarm Action OFF

User Edit Data

Preset 1~28

Swing 1~8

Pattern 1~4

Group 1~8

Undefined

Undefined

Undefined

Undefined

31

SPECIFICATION

Model

Mount Type

Image Sensor

Max. Pixels

Effective Pixels

Resolution

S/N Ratio

Zoom

Focal Length

Min. Illumination

Day & Night

Iris

Shutter Speed

AGC

White Balance

BLC

Range

Flickerless

SSNR Pan/Tilt

Speed

SS10C-C50H SS10W-C50H

Ceiling Mount Arm Type Wall Mount

1/4" Interline Transfer CCD

NTSC: 811(H)×508(V) 410K

PAL: 795(H)×596(V) 470K

NTSC: 768(H)×494(V) 380K

PAL: 752(H)×582(V) 440K

500 TV Lines (Color), 570 TV Lines (B/W)

50 dB (AGC Off) x10 Optical Zoom, x10 Digital Zoom

F1.8, f=3.8~38mm

0.7 Lux (Color) / 0.02 Lux (B/W), 50 IRE

Auto / Day / Night (ICR)

Auto / Manual

1/50 ~ 1/120,000 sec

Normal / High / Off

Auto / Manual (Red, Blue Gain Adjustable)

Low / Middle / High / Off

Selectable

Low / Middle / High / Off

Pan: 360



(Endless) ; Tilt 180



(Auto-flip, 95



(Normal)

Preset

Pattern

Swing

Group

Other Functions

Communication

Protocol

Privacy Zone

Alarm Input

OSD

Fan & Heater

Rated Power

Operation Temp.

Dimension

Weight

Preset: 360



/sec

Manual: 0.05



~360



/sec (Proportional to zoom)

Swing: 1~180



/sec

127 Preset (Label, Camera Image Setting)

4 Pattern, 1200 Commands (about 5 minute)/pattern

8 swing

8 groups (20 action entities per group)

Auto flip, Auto parking, Power up action, etc.

RS-485

Pelco-D, Pelco-P selectable

4 Zone

No 4 Input

Menu / PTZ Info, etc.

No

12V DC / 0.8 A

32°F ~ 104°F / 0



C~40

Ø5.04 x 7.36(H) inches /

Ø128 x 187(H) mm

2.65 lbs / 1.2 kg



C

Yes

12V DC / 1.1A

-22



F ~ 122



F / -30



C ~

50



C

Ø7.48 x 5.67(H) inches /

Ø190 x 144(H)mm

5.51 lbs / 2.5 kg

* Specifications are subject to change without notice.

MADE IN TAIWAN

Copyright © 2012. All Rights Reserved. www.okinausa.com

32

P-044_P-045

R201204-V27