Mattel Rock, Roll ‘n Ride Trike Instruction Sheet

Please keep this instruction sheet for future reference, as it contains important information.

Adult assembly is required.

Age: 1½ years - 5 years.

Weight Limit: 50 lbs. (23 kg).

Tools needed for assembly: Phillips Screwdriver,

Hammer and Scrap Block of Wood (all not included).

Actual product may appear different from the photos shown.

www.fisher-price.com

73528

R6153

W6139

Consumer Information

WARNING

TO AVOID SERIOUS INJURY:

• Continuous adult supervision required.

• Never use near cars and other motor vehicles, near streets, steps, sloped driveways, hills, roadways, alleys, swimming pools or other bodies of water.

• Always wear shoes.

• Never allow more than one (1) rider.

Label Application

Center

Handle

Place Center of

Label Here

Care

• Check plastic parts regularly and if broken or cracked, dispose of them properly.

• Check all fasteners regularly to be sure they are tight. If the fasteners are not tight, tighten them as necessary.

• To clean this product, use a mild soap and water solution and a clean cloth. Rinse clean with water to remove soap residue.

• Before applying the label, wipe the surface of the handle with a clean, dry cloth to remove any dust or oils.

• Remove the backing from the label.

• First, position the center of the label on the handle, as shown.

Then, smooth each end of the label outward to attach it to the handle.

• For best results, avoid repositioning a label once it has been applied to the handle.

Storage

CONSUMER ASSISTANCE

1-800-432-5437 (US & Canada)

1300 135 312 (Australia)

Flared End

Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.

Hearing-impaired consumers: 1-800-382-7470.

Outside the United States:

Canada: Mattel Canada Inc., 6155 Freemont Blvd.,

Mississauga, Ontario L5R 3W2; www.service.mattel.com.

Great Britain: Mattel UK Ltd, Vanwall Business Park,

Maidenhead SL6 4UB. Helpline: 01628 500303. www.service.mattel.com/uk

Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.

Australia: Mattel Australia Pty. Ltd., 658 Church Street,

Locked Bag #870, Richmond, Victoria 3121 Australia.

New Zealand: 16-18 William Pickering Drive,

Albany 1331, Auckland.

Handle Cover

Handle Pin

Handle Cover

Helpful Hint: To store for future use, position the handle covers with the flared end upright and attach them to the handle using the four screws. Insert the handle pin into either the holes in the base/handle or through the holes in the retainers. Store the base/handle in a safe place for future use as a ride-on rocker or learn to pedal trike.

2

Parts

Note: The base/handle assembly can be attached to the trike in either the Ride-on Rocker (page 8) or Learn to Pedal mode (page 9).

Parts not shown: Assembly Tool and Label.

Seat Pin

Seat

Handlebar

Frame Cover

Frame

Fork

Footrest

2 Fork Covers

Handle Bottom

Handle Pin

Front Wheel Assembly 4 Pedal Axle Covers

2 Base/Handle Covers

Straight Axle

2 Rear Wheels

Cap Nuts

2 Wheel Caps

Base

Handle Top

#8 x 3 /

4

" (1,9 cm)

Screw - 13

#10 x 3 /

4

" (1,9 cm)

Screw - 11

#8 x 3" (7,6 cm) Screw – 1

All fasteners are shown actual size. Tighten and loosen the screws with a

Phillips screwdriver. Do not over-tighten the screws. For your convenience, an extra cap nut is included.

3

Cap Nut – 1

Assembly

CAUTION

This product contains small parts in an unassembled state. Adult assembly is required.

• Please save all packaging material until assembly is complete to ensure that no parts are discarded.

• Please wipe each part with a clean, dry, cloth before assembling this product.

Rear Wheel

Spoke Side Up

Straight Axle

Straight Axle

1

Rear Wheel Spoke

Side Down

• Slide a rear wheel (spoke side down) onto the straight axle.

Assembly Tool

Cap Nut

Scrap Block of Wood

3

Assembled

Rear Wheel

• Turn the frame on its side with the exposed end of the straight axle up.

• Place the assembled rear wheel on the scrap block of wood.

• Slide the other rear wheel (spoke side up) onto the end of the straight axle.

• Place a cap nut on the end of the straight axle.

• Place the assembly tool over the cap nut and tap it with a hammer.

Gently pull the rear wheel up to be sure the cap nut is securely attached to the straight axle.

Frame

Rear Wheel

Wheel Cap Hole

Hole

Wheel Cap

4

Straight Axle

2

BOTTOM VIEW

• Turn the frame upside down.

• Insert the straight axle assembly through the holes in the rear of the frame.

• Fit the wheel cap into the center of the wheel. Tap the wheel cap with a hammer to secure it to the wheel.

• Fit the wheel cap into the center of the wheel. Tap the wheel cap with a hammer to secure it to the wheel.

• Set the frame assembly aside.

Pedal Axle Cover

Pedal Axle

Slot

Pedal Axle Cover

5

Metal Tab

4

• Fit two pedal axle covers onto the pedal axle metal tabs. Make sure the metal tabs fit into the slot in each pedal axle cover.

• While holding the pedal axle covers on the pedal axle, insert the pedal axle into the hole in the center of the front wheel.

• Push the pedal axle covers into the center of the front wheel until they are flush with the surface of the front wheel.

• Repeat this procedure with the other two pedal axle covers on the other side of the front wheel assembly.

Fork Cover

Front Wheel Assembly

Fork Arms

Assembly

Groove

Knobbed End

Frame Opening

Footrest

Footrest

Knobbed End

6

Pedal Axle

• Place the front wheel assembly between the fork arms so that the pedal axle fits into the groove at the bottom of each fork arm.

• Place a fork cover over the pedal axle on one fork arm.

• Insert two #10 x ¾" (1,9 cm) screws into the fork cover and tighten.

• Repeat this procedure to attach the other fork cover to the other fork arm, using the #10 x ¾" (1,9 cm) screws.

8

TOP VIEW

• Insert the knobbed end of the footrest up through the opening in the underside, center of the frame .

• Rotate the footrest ¼ turn .

• Slide the footrest toward the handlebar as far as it will go until the top of the footrest is positioned over the opening’s rectangular cut-out.

• Lower the knobbed end of the footrest into the rectangular cut-out in the frame .

Frame Cover

Handlebar

Frame Neck

Fork Post

Fork Covers

FIRST, insert the screw so that ¾" (1,9 cm) is visible.

THEN, tighten the screw.

¾" (1,9 cm)

9

• Place the frame cover over the frame opening. Make sure the holes in the frame cover align with the holes on the frame.

• Insert three #10 x ¾" (1,9 cm) screws into the frame cover and tighten.

Seat

7

• Turn the frame upright.

• Insert the fork post up through the hole in the frame neck.

Make sure the fork is positioned so that the fork covers face the rear wheels.

• Place the handlebar over the fork post and push it down onto the frame. Make sure the handlebar is positioned so that the screw hole faces the rear wheels and aligns with the screw hole in the fork post.

• Insert the #8 x 3" (7,6 cm) screw through the hole in the handlebar and into the fork post so that part of the screw (about

¾" - 1,9 cm) is still visible. Tighten the screw.

Seat Mount

10 Seat Mount Adjustment Holes

• Place the seat on the seat mount.

• Adjust the seat for your child’s comfort by aligning the hole in the seat with one of the seat mount adjustment holes.

5

Assembly

Grooves Wheel Retainers

11 Seat Pin

• While pushing down on the seat, insert the seat pin through the hole in the seat and into a seat mount adjustment hole.

Handle Top

Base

14

Base/Handle

• Place the base/handle assembly on a flat surface so that the wheel retainers are upright.

• Fit the trike onto the base/handle assembly so that the rear frame rests in the grooves in the base and the front wheel fits between the wheel retainers in the base/handle.

Flared End

Handle Cover

Handle Bottom

12

• Fit the handle top and bottom to the end of the base, as shown.

13

• Insert 13 - #8 x ¾" (1,9 cm) screws into the handle top and tighten.

15

• Position the base/handle covers so that the flared end faces the front of the trike.

• Fit the base/handle covers onto the trike rear frame near the rear wheels.

• Insert two #10 x ¾" (1,9 cm) screws into each base/handle cover and tighten.

6

Ride-on Rocker

IMPORTANT! Be sure to adjust the seat in the most forward position for Ride-on Rocker mode.

Learn to Pedal Trike

Base/Handle Pin

Front Wheel

Wheel Retainer Wheel Retainer

• Insert the base/handle pin through one wheel retainer, a hole in the front wheel and into the other wheel retainer.

• Push the handle pin to “snap” it into place. Pull on the handle pin to be sure it is secure.

1

Wheel Retainer

Front Wheel

Handle Pin

Wheel Retainer

• If you are converting from the ride-on rocker mode, remove the handle pin from the wheel retainers and front wheel.

Base/Handle

Base/Handle

Handle Pin

7

2

• Rotate the base/handle to the upright position.

• Insert the handle pin through one side of the base/handle, through the holes in the back of the frame and out through the hole in the other side of the base/handle. Make sure the handle pin “snaps” into place.

• Pull on the handle pin to be sure it is secure.

Pedal Trike

Base/Handle

IMPORTANT! It is a good practice to start training children very young regarding the importance of helmet use.

When children are older and riding bicycles and faster vehicles, it is important that they use a helmet each and every time they ride. For this reason, even while riding a tricycle, it is a good idea to familiarize your child with helmet use, so that it becomes a habit for life. Choose a helmet that complies with requirements of the applicable certifying agency for bicycle helmets.

2

• Rotate the base/handle down, under the trike, to the ride-on rocker position.

Base/Handle Cover

3

Base/Handle

• Remove the screws from the base/handle covers.

• Remove the base/handle covers.

• Remove the base/handle.

1 Base/Handle

Handle Pin

• If you are converting from the learn to pedal trike mode, remove the handle pin from the base/handle and the back of the frame.

4

• Rotate the footrest up toward the rear wheels and snap it into the recess in the underside of the frame.

PRINTED IN MEXICO

Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052, U.S.A.

©2011 Mattel, Inc. All Rights Reserved. ® and TM designate U.S. trademarks of Mattel, Inc.

R6153a-0921