MODEL:ALPHA

New born-7 years old

04301347

Headrest locator / shoulder strap height locator

9. Always make sure that any straps holding the seat restraint to the vehicle shall be tight , any straps restraining the child should be adjusted according to the child’s body, and check that the straps shall not be twisted.

10. Ensure that any lap strap is worn low down , so that the pelvis is firmly engaged, shall be stressed.

11. Do not use any load bearing contact points other than those described in the instructions and marked in the child restraint.

12. Any luggage or other objects liable to cause injuries in the event of a collision shall be properly secured.

13. The rigid items and plastic parts of a child restraint must be so located and installed that they are not liable , during everyday use of the vehicle to become trapped by a moveable seat or in a door of the vehicle.

14. To prevent from the risk of fall, your child should always be fastened.

15. It is dangerous to make any alteration or additions to the device without the approval of the competent authority, and a danger of not following closely the installation instructions provided by the child restraint manufacturer.

16.This child seat is designed for children from birth up to 25kg.Never overload the child seat more than one child or with other loads.

17. The child restraint must not be used without the cover.

18.The seat cover should not be replaced with any other than the one recommended by the manufacturer, because the cover constitutes an integral part of the restraint performance.

19. Before you adjust any movable or adjustable parts of your child seat

,you must remove your baby from the child seat.

20. The child seat should be kept away from sunlight if the seat is not provided with a textile, otherwise it may be too hot for the child’s skin.

21 .

Never use a second-hand product , as you can never be certain what was happened to it.

3

.

Usage

3.1 Install position of the child seat in vehicle

Correct fitting/suitable Incorrect fitting/not suitable

iagonal belt

and Lap belt

This child seat is suitable for conventional use in all cars equipped with three- point seat belts that are fitted in accordance with Euroapean standard(ECE 44 or equivalent standard)

Important:

The child seat must only be installed using a lap and diagonal seat belt.

Not to use them in seating positions where an active frontal airbag installed .

Only use on this seat if a lap and diagonal seat belt is fitted.

3.2 Checking the shoulder strap height

3

NO-Too low NO-Too high YES-Correct

Always check that the shoulder straps are at the correct height for your child. The child’s shoulders should always be thread through the slots in the cover and seat shell that are closest to the top of your child’s shoulders.

4

Steps to buckle the harness

Engage the buckle connecter until it clicks.

Press the red recline adjustment handle, and adjust the child restraint to the proper position.

There is one recline angle for baby mode (recline angle number 4), it is marked as blue triangles. There are three recline angles 1-3 for toddler mode, they are marked as red triangles. There are three recline angles 1-3 for junior mode, they are marked as red triangles.

3.6 Adjust the shoulder strap height and the headrest 3.7

4

4

Notice: be sure to loosen the harness before adjust the headrest locator/shoulder strap height locator ,see 3.4

Pull out the headrest locator, then you can adjust the height of the headrest up and down to ensure that the position of the headrest fits the child's shoulder height, and at the same time, the height of the shoulder strap will also be changed accordingly.

3

4

4

Step 3: Fasten the belts in the rearward blue safety-belt slots at the back of the body. Shoulder belt must pass through the rearward safety-belt slot. Fasten the belt.

Step 4: Open the lock-off device and insert the safety belt through it. While pressing the child seat, pull the belts to fasten the child seat tightly and securely. Lastly, slip the belt in to the hook.

18

Step 3: Open the lock-off device and insert the safety belt through it.

While pressing the child seat, pull the belts to fasten the child seat tightly and securely.

Step 2: Fasten the belts in the forward red safety-belt slots at the back of the body. Shoulder belt must pass through the safety-belt slot. Fasten the belt.

4

Step 3: Position shoulder belt through shoulder belt guide, pass waist belt through seat slots.

Fasten buckle and pull the vehicle belt to tighten

5

5

5.2 Washing instruction

Never use any solvant, chemical detergent or lubricant on any part of your child seat.

30 ℃

Hand wash, water temperature below 30 ℃

Do not bleach

P

Dryclean, any solvent except trichloroethylene.

Do not tumble dry Do not iron

6.3 Remove and assemble the fabric cover

1. Firstly, remove the crotch pad and buckle of the child seat (see 3 .

7 of page 8 , ) , and then remove the shoulder straps and comfortable cushion .

2. Remove the fabric cover of the child seat.To install the fabric cover, please operate follow the above instructions in reverse order.

7. The main technical parameters

Length ： 510mm

Width ： 610mm

Height ： 468mm

Weight ： 5.5

kg

13