advertisement
User’s manual for
EccoPC Notebook 15
2
Preface
Notice
The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated, trans- mitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered trade- marks of their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer.
©June 2017
Trademarks
Intel and Intel Core are trademarks/registered trademarks of Intel Corporation.
Preface
R&TTE Directive
This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Direc- tive 1999/5/EC.
This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Lux- embourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland,
United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slov- enia.
ErP Off Mode Power Consumption Statement:
The figures below note the power consumption of this computer in compliance with European Commission (EC) regulations on power consumption in off mode:
• Off Mode < 0.5W
I
Preface
CE Marking
This device has been tested to and conforms to the regulatory requirements of the European Union and has at- tained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market.
This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE
Marking. A notified body has determined that this device has properly demonstrated that the requirements of the directive have been met and has issued a favorable certificate of expert opinion. As such the device will bear the notified body number 0560 after the CE mark.
The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a product.
Secondly, CE Marking is mandatory for the product it applies to, whereas most quality markings are voluntary.
3
Preface
FCC Statement
(Federal Communications Commission)
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in- stalled and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Re orient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the service representative or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
1. This device may not cause interference.
And
2. This device must accept any interference, including interference that may cause undesired operation of the device.
4
Preface
FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not ex- pressly approved by the manufacturer for compliance with the above standards could void your authority to operate the equipment.
5
Preface
IMPORTANT SAFETY INSTRUCTIONS
Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment:
1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There may be a remote risk of electrical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.
5. This product is intended to be supplied by a Listed Power Unit:
• Full Range AC/DC Adapter – AC in 100 - 240V, 50 - 60Hz DC Output 19V, 4.74A ( 65/90 Watts ) minimum
This Com puter’s Optical Device is a Laser Class 1 Product
6
Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
Do not expose the computer to any shock or vibration.
Do not place it on an unstable surface.
Do not place anything heavy on the computer.
2. Keep it dry, and do n’t overheat it. Keep the computer and power supply away from any kind of heating ele- ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly dam- aged.
Do not expose it to excessive heat or direct sunlight.
Do not leave it in a place where foreign matter or moisture may affect the system.
Don’t use or store the computer in a humid environment.
Do not place the computer on any surface that will block the
Vents/Fan Intakes.
7
Preface
3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data.
4. Follow the proper working procedures for the computer. Shut the computer down properly and don ’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.
Do not turn off the power until you properly shut down all pro- grams.
Do not turn off any peripheral devices when the computer is on.
Do not disassemble the com- puter by yourself.
Perform routine maintenance on your computer.
5. Take care when using peripheral devices .
Use only approved brands of peripherals.
Unplug the power cord before attaching peripheral devices.
8
Preface
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and may expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply. Then refer servicing to qualified service personnel under any of the following conditions:
•
When the power cord or AC/DC adapter is damaged or frayed.
• If the computer has been exposed to rain or other liquids.
• If the computer does not work normally when you follow the operating instructions.
•
If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
•
If there is an unusual odor, heat or smoke coming from your computer.
Bottom Cover Removal Warning
Users should not remove any cover(s) and /or screw(s) for the purposes of device upgrade as this may violate the terms of your warranty. If you need to replace/remove the hard disk/RAM/optical device etc., for any reason, please contact your dis- tributor/supplier for further information.
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and screw(s) before restoring power to the system.
Also note the following when the cover is removed:
• Hazardous moving parts.
• Keep away from moving fan blades.
9
Preface
Power Safety
The computer has specific power requirements:
•
•
Power Safety Warning
Before you undertake any upgrade proce- dures, make sure that you have turned off the power, and disconnect- ed all peripherals and cables (including tele- phone lines and power cord).
•
•
•
•
Only use a power adapter approved for use with this computer.
Your AC/DC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifica- tions, consult your service representative or local power company.
The power adapter may have either a 2-prong or a 3-prong grounded plug. The third prong is an important safety feature; do not defeat its purpose. If you do not have access to a compatible outlet, have a qualified electrician install one.
When you want to unplug the power cord, be sure to disconnect it by the plug head, not by its wire.
Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices.
Before cleaning the computer, make sure it is disconnected from any external power supplies (i.e. AC/DC adapter or car adapter).
You must also remove your battery in order to prevent accidentally turning the machine on.
Before removing the battery disconnect the
AC/DC adapter from the computer.
Do not plug in the power cord if you are wet.
Do not use the power cord if it is broken.
Do not place heavy objects on the power cord.
1
0
Preface
Polymer/Lithium-Ion Battery Precautions
Note the following information which is specific to Polymer/Lithium-Ion batteries only, and where applicable, this overrides the general battery precaution information overleaf.
• Polymer/Lithium-Ion batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mechanism and is not a cause for concern.
• Use proper handling procedures when using Polymer/Lithium-Ion batteries. Do not use Polymer/Lithium-Ion batteries in high ambient temperature environments, and do not store unused batteries for extended periods.
• If you are working in areas of low temperature use the AC/DC adapter to power the computer.
See also the general battery precautionary information overleaf for further information.
11
Preface
General Battery Precautions
• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
• Do not remove any batteries from the computer while it is powered on.
• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
• If you do not use the battery for an extended period, then remove the battery from the computer for storage.
• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
•
Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative or qual- ified service personnel.
• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries may explode or leak if exposed to fire, or improperly handled or discarded.
•
Keep the battery away from metal appliances.
• Affix tape to the battery contacts before disposing of the battery.
• Do not touch the battery contacts with your hands or metal objects.
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacture r’s instructions.
12
Preface
Cleaning
Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Travel Considerations
As you get ready for your trip, run through this list to make sure the system is ready to go:
1. Check that the battery pack and any spares are fully charged.
2. Power off the computer and peripherals.
3. Close the display panel and make sure it ’s latched.
4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
5. The AC/DC adapter uses voltages from 100 to 240 volts so you wo n’t need a second voltage adapter. However, check with your travel agent to see if you need any socket adapters.
6. Put the notebook in its carrying bag and secure it with the bag ’s straps.
7. If yo u’re taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters and/or cables.
8. Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership for both hard- ware and software. Make sure your “papers” are handy.
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intakes while the computer is in use.
13
Preface
Packing
As you get ready for your trip, run through this list to make sure the system is ready to go:
1. Check that the battery pack and any spares are fully charged.
2. Power off the computer and peripherals.
3. Close the display panel and make sure it ’s latched.
4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
5. The AC/DC adapter uses voltages from 100 to 240 volts so you wo n’t need a second voltage adapter. However, check with your travel agent to see if you need any socket adapters.
6. Put the notebook in its carrying bag and secure it with the bag ’s straps.
7. If yo u’re taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters and/or cables.
8. Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership for both hard- ware and software. Make sure your documents are prepared.
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a notebook which is powered on in a travel bag may cause the vent(s)/fan intake(s)/outlet(s) to be blocked. To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s)/outlet(s) while the computer is in use.
14
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind:
Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knock- ing the computer against hard objects.
Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the com- puter, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note :
Some airports also scan luggage with these devices.
Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight.
These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies) charged.
Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer.
Wait a few minutes before turning it on so that any moisture can evaporate.
15
Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in front of the computer for long periods of time.
Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain:
• Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
•
Your knees should be slightly higher than your hips. Place your feet flat on the floor or on a footrest if necessary.
• Use a chair with a back and adjust it to support your lower back comfortably.
•
Sit straight so that your knees, hips and elbows form approximately 90-degree angles when you are working.
• Take periodic breaks if you are using the computer for long periods of time.
Remember to:
• Alter your posture frequently.
•
Stretch and exercise your body several times a day.
•
Take periodic breaks when you work at the computer for long periods of time. Frequent and short breaks are better than fewer and longer breaks.
16
Preface
Lighting
Proper lighting and a comfortable viewing angle can reduce eye strain and shoulder and neck muscle fatigue.
•
Position the display to avoid glare or reflections from overhead lighting or outside sources of light.
• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.
• Position the display directly in front of you at a comfortable viewing distance.
• Adjust the display-viewing angle to find the best position.
LCD Screen Care
To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for an extended period of time) take the following precautions:
• Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time.
•
Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).
•
Rotate desktop background images every few days.
• Turn the monitor off when the system is not in use.
LCD Electro-Plated Logos
Note that in computers featuring a raised LCD electro-plated logo, the logo is covered by a protective adhesive.
Due to general wear and tear, this adhesive may deteriorate over time and the exposed logo may develop sharp edges. Be careful when handling the computer in this case, and avoid touching the raised LCD electro-plated logo. Avoid placing any other items in the carrying bag which may rub against the top of the computer during transport. If any such wear and tear develops contact your distributor/supplier.
17
Preface
18
Preface
Contents
Quick Start Guide
19
Preface
Storage Devices, Mouse, & Audio
20
Preface
Power Management
21
Preface
Drivers & Utilities
22
Preface
BIOS Utilities
23
Preface
24
Preface
Modules
25
Preface
Troubleshooting
Interface (Ports & Jacks)
26
Preface
Control Center
Overview ................................................................................................................................................... B-1
Power Modes ............................................................................................................................................ B-2
Control Center Menus ...............................................................................................................................B-3
Power Status (System Program) ............................................................................................................. B-4
CPU Temperature (System Program) ...................................................................................................... B-4
Brightness (System Program) ..................................................................................................................B-4
Volume (System Program) .......................................................................................................................B-4
Fan Speed (System Program) ...................................................................................................................B-4
This system supports Energy Star power ............................................................................................. B-5
Sleep Button (System Program) .............................................................................................................. B-5
Display Switch (System Program) ........................................................................................................... B-5
Time Zone (System Program) .................................................................................................................B-5
27
Preface
Desktop Background (System Program) ................................................................................................. B-6
Backlight Keyboard (Device) ...................................................................................................................B-6
TouchPad/PC Camera (Device) ............................................................................................................... B-6
Caps Lock/Scroll Lock/ Number Lock/Airplane Mode ...........................................................................B-6
Video Driver Controls
Specifications
28
Preface
29
Preface
30
Quick Start Guide
Chapter 1: Quick Start Guide
Overview
This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following:
• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices ( hard disk and card reader ) , TouchPad & Mouse and Audio Features .
•
•
Chapter 3 The computer’s power management options.
Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems.
•
•
Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).
Chapter 6 A quick guide to the computer’s PC Camera, Wireless LAN, Bluetooth & WLAN Combo,
Sound Blaster Audio and Intel modules (some of which may be optional depending on your pur- chase configuration).
•
•
Chapter 7 A troubleshooting guide.
Appendix A Definitions of the interface , ports / jacks which allow your computer to communicate with external devices.
•
•
•
Appendix B Information on the Control Center .
Appendix C Information on the Video driver controls.
Appendix D The computer’s specification .
1
Overview 1 - 1
1
Quick Start Guide
Advanced Users
If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
to refer to “Drivers & Utilities” on page 4 - 1
and “BIOS Utilities” on page 5 - 1 in the User’s Manual. You
may also find the notes marked with a
of interest to you.
Notes
Check the light colored boxes with the mark above to find detailed information about the computer
’s features.
Beginners and Not-So-Advanced Users
If you are new to computers (or do not have an advanced knowledge of them) then the information contained in this Quick Start Guide should be enough to get you up and running. Eventually you should try to look through all the documentation (more detailed descriptions of the functions, setup and system controls are covered in the remainder of the User’s Manual), but do not worry if you do not understand every- thing the first time. Keep this manual nearby and refer to it to learn as you go. You may find it useful to refer to the notes marked with a as indicated in the margin.
For a more detailed description of any of the interface ports and jacks see
(Ports & Jacks)” on page A - 1 .
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the
symbol. Also please note the safety and handling instructions as indicated in the Preface .
1 - 2 Overview
Quick Start Guide
Not Included
Operating Systems (e.g. Windows 10 ) and applications (e.g. word processing, spreadsheet and database pro- grams) have their own manuals, so please consult the appropriate manuals.
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the appropriate drivers. Drivers are programs which act as an interface between the computer and a hardware component
system hasn
” on page 4 - 1 for installation instructions.
Ports and Jacks
puter to communicate with external devices, connect to the internet etc.
1
Overview 1 - 3
1
Quick Start Guide
System Software
Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 10 (64-bit) operating system is supported.
Windows OS
Note that the information included on the following pages is for Windows 10 only .
In order to run Windows 10 (64-bit) your computer requires a minimum 2GB of system memory (RAM).
1 - 4 Overview
Quick Start Guide
System Startup
1. Remove all packing materials, and place the computer on a stable surface, and securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.
2. When first setting up the computer use the following procedure (as to safeguard the computer during shipping, the battery will be locked to not power the system until first connected to the AC/DC adapter and initially set up as below):
• Attach the AC/DC adapter cord to the DC-In jack on the right of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter and leave it there for 6 seconds or longer .
• Remove the adapter cord from the computer’s DC-In jack, and then plug it back in again; the battery will now be unlocked.
3. Use one hand to raise the lid/LCD to a comfortable viewing angle (it is preferable not to exceed 135 degrees); use the other hand to support the base of the computer ( Note : Never lift the computer by the lid/LCD).
4. Press the power button on the top of the computer for about 2 - 3 seconds to turn the computer “ on ” (note that the power LED on the front of the computer will turn from orange to green when the computer powers on).
135
°
Shutdown
Figure 1 - 1 - AC/DC Adapter In / Opening the Lid/LCD
Note that you should al- ways shut your comput- er down by choosing the
Shut Down command in Windows (see page
prevent hard disk or system problems.
1
System Startup 1 - 5
1
Quick Start Guide
Figure 1 - 2
LCD Panel Open
1. Built-In PC Camera
2. PC Camera LED
3. Built-In Array
Microphone
4. LCD
5. Power Button
6. Keyboard
7. TouchPad & Buttons
LCD Panel Open
3 2
1
4
5
6
Note that the Touchpad/
Clickpad and Buttons has a valid operational area indi- cated within the dotted lines above.
7
3
1 - 6 LCD Panel Open
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission de- vices (e.g. WLAN, Blue- tooth or 3G/4G) aboard aircraft is usually prohibited.
Make sure any wireless modules are OFF (i.e. the system is in Airplane
Mode ) if you are using the computer aboard aircraft.
Use Fn + F11 Airplane
Mode key combination to toggle Airplane Mode On/
Off, and check the LED indi- cator for the power status.
Quick Start Guide
LED Indicators
The LED indicators at the front of the computer display helpful information about the current status of the sys- tem.
Icon Color Description
Orange
Blinking Orange
Green
Orange
Green
Blinking Green
Green
Green
The Battery is Charging
The Battery has Reached Critically Low Power Status
The Battery is Fully Charged
AC/DC Power is Plugged In
The Computer is On
The Computer is in Sleep Mode
HDD Activity
Airplane Mode is ON (the WLAN, Bluetooth & 3G/4G Modules are OFF)
Table 1 - 1 - LED Indicators
1
LCD Panel Open 1 - 7
1
Quick Start Guide
Other Keyboards
If your keyboard is dam- aged or you just want to make a change, you can use any standard USB detect and enable it auto- matically. However spe- cial functions/hot-keys unique to the system’s regular keyboard may not work.
Scr Lk
Hold down the Fn Key and Scr Lk to enable scroll lock and check the
LED indicator for status.
Keyboard
The keyboard (or the factory option white illuminated LED keyboard) has an embed- ded numerical keypad for easy numeric data input, and features function keys to al-
low you to change operational features instantly. See Table 1 - 3, on page 1 - 12 for
full function key combination details.
Function Keys
Play/Pause Key
ScrLk &
NumLk Keys
Numerical
Keypad
Fn Key
Windows Logo Key Menu/Application Key
Figure 1 - 3 - Keyboard
Special Characters
Some software applications allow the number-keys to be used with Alt to produce special characters.
These special characters can only be produced by using the numeric keypad. Regular number keys (in the upper row of the keyboard) will not work. Make sure that NumLk is on.
1 - 8 Keyboard
Quick Start Guide
Keyboard Application Settings
( Illuminated Keyboard Option )
If your computer includes an illuminated keyboard (factory option), you will need to install the keyboard Con- trol Center
as appropriate for your model’s configuration (you can only select keyboards supported by your system). After the driver has been installed, and the system restarts, the control panel below will pop-up to allow you to select the illuminated white keyboard for your system. Click Save to retain the setting chosen.
If you wish to change the setting at any time then right-click on the Control Center icon and select Key- board Settings to return to the keyboard select control panel.
1
Right-click and select Keyboard Settings .
Figure 1 - 4 - Keyboard Settings for Illuminated Keyboard Option
Keyboard Application Settings 1 - 9
1
Quick Start Guide
Control Center
When in the Windows Desktop application (not in the Start screen) press the Fn + Esc key combination, or double-click the icon in the notification area of the taskbar to toggle the Control Center on/off. The Con- trol Center gives quick access to frequently used controls and enables you to quickly turn the camera/touch pad
on/off (see Appendix B for full details).
Control Center Access
To run the
Control Cen- ter press the
Fn + Esc key combination, or double- click the icon in the noti- fication area of the taskbar.
Close the Control Center by clicking the close icon in the top right of the panel (move the cursor onto the top right corner of the panel to highlight it).
Figure 1 - 5 - Control Center
1 - 10 Control Center
Keyboard Shortcuts
The following Windows Logo Key (Winkey) keyboard shortcuts are useful for navi- gation/operation in Windows 10 .
Windows Logo
Key +
Description
Tap Winkey
A
Toggle the
Open the
Start menu
Action Center
B Select the Taskbar Notification Area
Launch Cortana (in listening mode) C
D Toggle the Desktop
Launch File Explorer (Quick Access tab) E
+ Number (1, 2, etc) Launch an application from the taskbar (numbered from left to right)
Table 1 - 2 - Keyboard Shortcuts
Quick Start Guide
Windows Logo
Keyboard Shortcut
Use the Windows logo key + D key com- bination to switch be- tween the Start screen and Windows Desktop.
Menu/Application
Keyboard Shortcut
When the Desktop app is running you can use the Menu/Application key on the key- board to display the context menu as per a mouse right-click.
1
Control Center 1 - 11
1
Quick Start Guide
Function Keys & Visual Indicators
The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down.
Keys Function/Visual Indicators Keys Function/Visual Indicators
Fn +
Fan Control Toggle
Automatic / Full
Power
Fn +
Control Center Toggle
Play/Pause (in Audio/Video Programs) Display Toggle
Fn + Fn +
Touchpad Toggle Brightness Decrease/Increase
Fn + Fn +
Turn LCD Backlight Off
(Press a key to or use Touchpad to turn on)
PC Camera
Power Toggle
Fn +
Fn +
Fn +
Fn +
Fn +
Mute Toggle
For Backlight
Keyboards Only Toggle
Off/High/Low
Volume Decrease/Increase
Fn +
Fn +
Airplane
Mode Toggle
Sleep Toggle
Table 1 - 3 - Function Keys & Visual Indicators
1 - 12 Control Center
Front & Rear Views
1
2
2
3
Multi-in-1 Card Reader
The card reader allows you to use the most popular digital storage card formats:
MMC (MultiMedia Card) / RSMMC
SD (Secure Digital) / Mini SD / SDHC / SDXC
Quick Start Guide
Figure 1 - 6
Front & Rear Views
1. Multi-In-1 Card
Reader
2. LED Indicators
3. Battery
1
Front & Rear Views 1 - 13
1
Quick Start Guide
Figure 1 - 7
Right & Left Views
1. S/PDIF-Out Jack
2. Microphone Jack
3. Headphone Jack
4. 1 * USB 2.0 Port
5. Optical Device Drive
Bay (for DVD Device)
6. DC-In Jack
7. Security Lock Slot
8. HDMI-Out Port
9. RJ-45 LAN Jack
10. External Monitor Port
11. Vent/Fan Intake
12. 1 * USB 3.0 Port (USB
3.1 Gen 1 - Type C )
13. 2 * USB 3.0 Ports (USB
3.1 Gen 1 - Type A )
OR
12. 1 * USB 3.1 Port (USB
3.1 Gen 2 - Type C ) &
13a. 1 * USB 3.1 Port
(USB
3.1 Gen 2 - Type A )
( Factory Option )
13b. 1 * USB 3.0 Port (USB
3.1 Gen 1 - Type A )
Right & Left Views
Right
1 2 3 4
Left
11
5
12 13a 13b
6
7
8
9
10
USB 3.0 / 3.1 Port OR USB 2.0 Port
This model includes 2 * USB 3.0 ports (USB 3.1 Gen 1 Type A ), 1 * USB 3.0 port (USB 3.1
Gen 1 Type C ) and 1 * USB 2.0 port.
Note : 1 * USB 3.1 (Gen 2 Type C)
12 and 1 * USB 3.1 (Gen 2 Type A)
13a ports are available as a factory option for this computer model series. The USB 3.1 ports are shared with the USB 3.0 ports in this option.
USB 3.1 Port Speed
Note that when a single USB device is plugged in to a USB 3.1 (Gen 2) port the data transfer speed will be 10Gbps, however when two devices are plugged in to both USB 3.1 (Gen 2) ports, this band- width will be shared between the ports..
1 - 14 Right & Left Views
Disk Eject Warning
Don’t try to eject a CD/DVD while the system is ac- cessing it. This may cause the system to
“crash”. Stop the disk first then eject it, or press the stop button twice.
CD/DVD Emergency Eject
If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. Do not use a sharpened pencil or any ob- ject that may break and become lodged in the hole.
D on’t try to remove a floppy disk/CD/DVD while the system is accessing it. This may cause the system to
“crash”.
Quick Start Guide
1
Changing DVD Regional Codes
Go to the Control Panel and double-click Device Man- ager (Hardware and Sound), then click the + next to
DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialog box, and se- lect the DVD Region (tab) to bring up the control pan- el to allow you to adjust the regional code).
DVD region detection is device dependent, not OS- dependent. You can select your module
’s region code 5 times. The fifth selection is permanent. This cannot be altered even if you change your operating system or you use the module in another computer
(see “DVD Regional Codes” on page 2 - 5 ).
Right & Left Views 1 - 15
1
Quick Start Guide
USIM Card
Orientation
Note that the USIM card’s readable side
(with the gold-colored contacts) should face downwards as illustrat- ed.
Figure 1 - 8
USIM Card Insertion
3G/4G Module USIM Card Installation
“Removing the Battery” on page 1 - 18
USIM card 1 as illustrated below (pay careful attention to the orientation of the card as the gold contact side of the card should face downwards) until it clicks fully into position. To eject the card simply press it until it ejects, but do not attempt to eject the card while connected to a 3G/4G network (see below).
1
USIM Card Ejection
Simply press on the USIM card to eject it, however do not do this while a connection is in progress. If you do eject the card while a 3G/4G connection is ongoing, you will need to shut down the system, re- insert the USIM card, restart the system and then reestablish the 3G/4G connection.
If you wish to change USIM cards then you will need to shut the system down, reinsert the USIM card, restart the system and then reestablish the 3G/4G connection.
1 - 16 Right & Left Views
Bottom View
2
1
1
3
1
1
2
Battery Information
Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharg- es.
Overheating
To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s) while the computer is in use.
Bottom Cover Removal
Warning
Do not remove any cover(s) and /or screw(s) for the purposes of device upgrade as this may vio- late the terms of your warranty.
If you need to replace/remove the hard disk/
RAM/optical device etc., for any reason, please contact your distributor/ supplier for further infor- mation.
Quick Start Guide
Figure 1 - 9
Bottom View
1. Fan Outlet/Intake
2. Speakers
3. Component Bay
Cover
1
Bottom View 1 - 17
1
Quick Start Guide
Removing the Battery
It is possible to remove the battery from the computer, however we recommend that you do not remove the bat- tery yourself. If you do need to remove the battery for any reason (e.g. long term storage) see below.
1. Turn the computer off , and turn it over.
2. Slide the latch
3. Slide the latch
1
2 in the direction of the arrow. in the direction of the arrow, and hold it in place.
4. Slide the battery out in the direction of the arrow 3 .
5. Reinsert the battery as illustrated below 4 .
6. Make sure the latches are returned to the lock position 5 .
1
4
2
5
3
5
Bottom Cover Removal
Warning
Do not remove any cover(s) and /or screw(s) for the pur- poses of device upgrade as this may violate the terms of your warranty.
If you need to replace/remove the hard disk/RAM/optical device etc., for any reason, please contact your distributor/supplier for further information.
Figure 1 - 10 - Battery Removal & Insertion
1 - 18 Removing the Battery
Quick Start Guide
Windows 10 Start Menu
Most of the apps, control panels, utilities and programs within Windows 10 can be accessed from the Start
Menu by clicking the icon in the taskbar in the lower left corner of the screen (or by pressing the Windows
Logo Key on the keyboard).
Windows Screens
Note that the Win- dows screens on the following pages are included as a basic guide and introduc- tion to navigating around Windows 10 .
However note that these screens are al- ways subject to change, upgrade and redesign. Check the
Microsoft website for details.
Desktop
Figure 1 - 11 - Windows Start Menu
1
Windows 10 Start Menu 1 - 19
1
Quick Start Guide
Right-Clicking the Windows Logo In Start Menu
Right-click the Start Menu icon (or use the Windows Logo Key + X key combination) to bring up an advanced Context Menu of useful features such as Apps and Features, Power Options, Task Manager, Search,
File Explorer, Device Manager, Computer Management and Network Connections etc.
Right-Click Icon
Figure 1 - 12 - Right-Click Windows Logo in Start Menu
1 - 20 Windows 10 Start Menu
Quick Start Guide
Start Menu Apps & Tiles
The Windows 10 Start Menu will contain a number of apps, and many more will be installed as you add more applications etc. Not all of these apps can fit on the screen so may need click and drag the handles at the edge of the screen to expand the menu in order to view all the apps (you can use the scroll bar to move up and down the screen).
1
Figure 1 - 13 - Expanding the Start Menu
Windows 10 Start Menu 1 - 21
1
Quick Start Guide
Pining/Unpinning Apps & Programs to/from the Start Menu
To make things easy to find you can add and remove tiles for apps and programs to the Start Menu. Right-Click on a program’s icon and select Pin to Start from the drop-down menu. To remove an app or program from the
Start Menu right-click the icon and select Unpin from Start . You can use the same method to pin apps/pro- grams to/from the taskbar (select pin to taskbar/unpin this program from the taskbar).
Figure 1 - 14 - Pin to Start/Unpin from Start
1 - 22 Windows 10 Start Menu
Quick Start Guide
Windows 10 Control Panel
In many instances throughout this manual you will see an instruction to open the Control Panel . The Control
Panel can be accessed in a number of ways in Windows 10 .
• Select
Control Panel
under the Windows
System item in the
Start Menu .
•
Type
Control Panel
into the
Search
box in the taskbar and click on the icon when it pops up.
•
You can pin the
Con- trol Panel
tile to
Start
or
taskbar.
Figure 1 - 15 - Windows 10 Control Panel Access
Windows 10 Control Panel 1 - 23
1
1
Quick Start Guide
Settings
The Settings item in the Start Menu (and also as an App) gives you quick access to a number of system settings control panels allowing you to adjust settings for System, Devices, Network & internet, Personalization, Apps,
Accounts, Time & language, Gaming, Ease of Access, Privacy and Update & security.
1 - 24 Windows 10 Control Panel
Figure 1 - 16 - Settings
Quick Start Guide
Windows 10 Taskbar
In many instances throughout this manual you will see an instruction to access the notification area of the task- bar . The notification area of the taskbar in the bottom right of the screen. Some of the Control Panels and appli- cations referred to throughout the course of this manual can be accessed from here.
1
Taskbar
Taskbar - Pinned Programs and Apps Notification Area
Figure 1 - 17 - Taskbar
You can pin/unpin apps to/from the taskbar in much the same way as you can to the Start screen (see “Pining/
Unpinning Apps & Programs to/from the Start Menu” on page 1 - 22 ).
Windows 10 Control Panel 1 - 25
1
Quick Start Guide
Action Center
The Action Center appears as a vertical panel on the right side of the screen when you swipe in from the right or click the button in the notification tray. This gives you access to commonly needed functions like Network,
All Settings, Airplane Mode, and Project etc.
Figure 1 - 18 - Action Center
1 - 26 Windows 10 Control Panel
Quick Start Guide
Video Features
You can switch display devices, and configure display options, from the Display settings (click the Start Menu and click Settings > System or right-click the desktop and select Display settings ) control panel. In Windows
10 it is possible to quickly configure external displays from the Project menu ( press the Windows logo key on your keyboard and the P key or Fn + F7 ).
To Configure Displays using Project
1. Attach your display to the appropriate port, and turn it on.
2. Press the + P key combination.
3. Click on any one of the options from the menu to select PC screen only ,
Duplicate , Extend or Second screen only .
4. You can also click Connect to a wireless display at the bottom of the
Project screen and follow the steps to connect to any wireless enabled display.
Figure 1 - 19 - Project (Devices)
1
Video Features 1 - 27
1
Quick Start Guide
To access the Display Settings:
1. You can quickly adjust the display by right-clicking the desktop and selecting Display Settings .
2. Adjust the settings for Brightness and color , Scale and layout , Resolution and Orientation from the menus.
3. When and external display is attached you can arrange the display configuration from the Multiple Displays menu, and arrange the configuration from Select and rearrange displays .
4. Click Apply to save any changes made.
Figure 1 - 20 - Display Settings
1 - 28 Video Features
Quick Start Guide
To access the Intel(R) HD Graphics Control Panel :
1. Right-click the desktop and select Intel(R) Graphics Settings from the menu.
OR
2. Click the icon in the notification area of the Desktop taskbar and select Intel(R) Graphics Settings from the menu.
1
Figure 1 - 21 - Intel Graphics Control Panel
Video Features 1 - 29
1
Quick Start Guide
Minimum Screen Resolution Settings
1. Windows 10 has minimum screen resolution requirements.
2. Right-click a blank area of the Desktop and select Display Settings .
3. Adjust the Resolution to make sure that it is at least 1024 * 768, although preferably 1366 * 768 or above.
Figure 1 - 22 - Display (Resolution)
1 - 30 Video Features
Quick Start Guide
Power Options
Power Options (Hardware and Sound) can be accessed from the Control Panel. The Power button item in
Start Menu (or the context menu) may be used to Shut down or Restart (you can also add Hibernate/Sleep to the menu - see page 1 - 32 ). To fully control all the power options (including Hibernate mode) go to the Power
Options control panel and configure the power button, sleep button and lid to perform the function selected.
Using the Power Button
1. Go to the Start Menu .
2. Click the Power button .
3. Select the power state required from the menu.
Figure 1 - 23 - Shut Down/Restart
Power Options 1 - 31
1
1
Quick Start Guide
You can also use the context menu (right-click the Start Menu icon or press the Windows logo + X key combination) to Sign out, Sleep , Hibernate , Shut down , and Restart .
Adding Hibernate/Sleep to the Power Men
1. Go to the Power Options ( Hardware and Sound ) control panel (or go to Windows Settings > Power & sleep >
Additional power settings ).
2. Click Choose what the power buttons do .
3. Cli ck “ Change settings that are currently unavailable ”
.
4. Click to put a check in the Hibernate/Sleep box under
Shutdown settings .
5. Click Save Changes and close the control panel.
Figure 1 - 24 - Context Menu Shut Down or sign out
Ctrl + Alt + Delete Key Combination
You can use the CTRL + ALT + DEL key combination to bring up a full-screen displaying Lock , Sign out ,
Change a password, Task Manager and Switch User . If you click the Power icon in the lower right corner of the screen a power management option menu appears to display Sleep , Hibernate , Shut down , and Restart .
1 - 32 Power Options
Storage Devices, Mouse, & Audio
Chapter 2: Storage Devices, Mouse, & Audio
Overview
Read this chapter to learn more about the following main features and components of the computer:
•
Hard Disk Drive/Solid State Drive
•
•
•
•
2
Overview 2 -
33
2
Storage Devices, Mouse, & Audio
Hard Disk Drive/Solid State Drive
Bottom Cover
Removal Warning
Do not remove any cov- er(s) and /or screw(s) for the purposes of device upgrade as this may vio- late the terms of your warranty.
The hard disk drive (HDD) and/or solid state drive (SSD) is used to store your data in the computer. The hard disk can be taken out to accommodate other serial (SATA)
“Storage” on page D - 2 for specification information), how-
ever you will need to contact your distributor/supplier to do this in order to avoid violating the terms of your warranty.
If you need to replace/ remove the hard disk for any reason, please con- tact your distributor/sup- plier for further information.
2 - 2 Hard Disk Drive/Solid State Drive
Storage Devices, Mouse, & Audio
Optical (CD/DVD) Device
There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual de-
vice will depend on the module you purchased (see
optical device is usually labeled “ Drive D:
” and may be used as a boot device if properly set in the BIOS
(see “Boot Menu” on page 5 - 15 ).
Sound Volume
Adjustment
How high the sound vol- ume can be set depends on the setting of the vol-
Loading Discs
ume control within Win-
To insert a CD/DVD, press the open button 1 and carefully place a CD/DVD onto dows . Click the Volume the disc tray with label-side facing up (use just enough force for the disc to click onto icon on the taskbar to the tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks” and you check the setting (see
are ready to start. The busy indicator 2 will light up while data is being accessed,
or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupt- ed, insert an object such as a straightened paper clip into the emergency eject hole
3 to open the tray.
Figure 2 - 1
Optical Device
2
1
3
2
Optical (CD/DVD) Device 2 -
35
2
Storage Devices, Mouse, & Audio
CD Emergency Eject
If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharp- ened pencil or similar object that may break and become lodged in the hole.
Handling CDs or DVDs
Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.
Note the following:
•
Hold the CD or DVD by the edges; do not touch the surface of the disc.
•
Use a clean, soft, dry cloth to remove dust or fingerprints.
•
Do not write on the surface with a pen.
• Do not attach paper or other materials to the surface of the disc.
• Do not store or place the CD or DVD in high-temperature areas.
•
Do not use benzene, thinner, or other cleaners to clean the CD or DVD.
•
Do not bend the CD or DVD.
•
Do not drop or subject the CD or DVD to shock.
Disk Eject Warning
Don’t try to remove a
CD/DVD while the sys- tem is accessing it. This may cause the system to
“crash”.
2 - 4 Optical (CD/DVD) Device
DVD Regional Codes
To change the DVD regional codes:
Storage Devices, Mouse, & Audio
DVD Region Note
1. Go to the Control Panel
2. Double-click Device Manager (Hardware and Sound) , then click the + next to
DVD/CD-ROM drives .
3. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code.
•
Region 1 - USA & Canada
• Region 2 - Western Europe, Japan,
South Africa, Middle East & Egypt
•
Region 3 - South-East Asia, Taiwan,
South Korea, The Philippines, Indo- nesia, Hong Kong
DVD region detection is device dependent, not
OS-dependent. You can select your mo dule’s re- gion code 5 times. The fifth selection is perma- nent. This cannot be al- tered even if you change your operating system or you use the module in another computer.
• Region 4 - South & Central Amer- ica, Mexico, Australia, New Zealand
• Region 5 - N Korea, Russia, Eastern
Europe, India & Most of Africa
• Region 6 - China
Figure 2 - 2
DVD Region Codes
2
Optical (CD/DVD) Device 2 -
37
2
Storage Devices, Mouse, & Audio
Multi-in-1 Card Reader
Push-Push Card
Reader
The card reader fea- tures a push-in/push-out card insertion and ejec- tion mechanism. Simply push the card to insert and eject it, however Ms
Duo cards require an adapter.
The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the Card Reader driver
(see “Card Reader” on page 4 - 7 ).
•
MMC (MultiMedia Card) / RSMMC
•
SD (Secure Digital) / Mini SD / SDHC / SDXC
Note : Some of these cards require PC adapters that are usually supplied with the cards.
1
Figure 2 - 3
Front View
1. Card Reader
2 - 6 Multi-in-1 Card Reader
Audio Features
Storage Devices, Mouse, & Audio
You can configure the audio options on your computer from the Sound control panel in Windows , or from the Realtek HD Audio Manager icon in the taskbar notification area/control panel (right-click the taskbar notification area icon to bring up an audio menu). The volume may also be adjusted by means of the volume icon in the taskbar or the audio slider in the Settings menu (see sidebar) .
Volume Adjustment
The sound volume level can be clicking using the volume control icon in the notification area of the taskbar .
Right-click the icon to access the menu above.
Figure 2 - 4
Realtek Audio
Manager
“HDMI Audio Configuration” on page C - 20 for a description of the audio configuration
when connecting an HDMI supported display device.
Audio Features 2 -
39
2
2
Storage Devices, Mouse, & Audio
Setup for Audio Recording
Disabling Front Jack
Detection
To record audio sources on your computer at optimum quality follow the instruc- tions below:
It is recommended that you do not disable front panel jack detection in
Connector Settings .
1. Go to the Control Panel .
2. Click Realtek HD Audio Manager ( Hardware and Sound ), or right-click the taskbar icon and select Sound Manager .
3. Click Microphone Effects (tab) in Microphone (tab), and then click to select
Noise Suppression (button), or adjust the Recording Volume level to around 60 , to obtain the optimum recording quality.
4. Click OK to close the control panel and save the settings.
Disabling front panel jack detection may cause your internal microphone to become disabled, and audio may continue to play through the sys- tem’s internal speakers even when headphones are plugged-in to the headphone jack (see
Figure 2 - 5
Realtek Audio
Manager - Recording
Setup
2 - 8 Audio Features
Touchpad and Buttons/Mouse
Storage Devices, Mouse, & Audio
The Touchpad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The Touchpad buttons function in much the same way as a two-button mouse.
Touchpad Cleaning
In order to improve pad performance it is neces- sary to keep the surface clean and free of finger- prints and marks etc.
Use a soft dry cleaning cloth to keep the pad surface clean.
Disabling the Pad
Use the Fn + F1 or Con- trol Center button to dis- able the Touchpad.
2
Touchpad and Buttons/Mouse 2 -
41
2
Storage Devices, Mouse, & Audio
Touchpad Sensitivity
TouchPad Scrolling
This computer model se- ries may feature different
TouchPad versions.
These TouchPads may differ in their vertical scrolling function in most scrollable windows.
Some TouchPads require sliding the finger up and down on the right of the
TouchPad to scroll the window. Other versions require tapping/holding down the finger at the top right or bottom right of the
TouchPad to scroll the window.
The mouse button zones at the bottom of the pad measure about 15mm from the bottom of the pad, and the left and right buttons are divided roughly down the mid- dle as illustrated below. Press the left button zone for a left click, and right button zone for a right click action.
Mouse Driver
If you are using an external mouse your operating system may be able to auto-configure your mouse during its installa- tion or only enable its basic functions. Be sure to check the de vice’s user documenta- tion for details.
Figure 2 - 6
Touchpad
Sensitivity
2 - 10 Touchpad and Buttons/Mouse
Touchpad Configuration
Storage Devices, Mouse, & Audio
Once you have installed the TouchPad driver (see
can configure the functions from the Mouse control panel in Windows , or by double- clicking the TouchPad driver icon in the notification area of the taskbar in the
Desktop app. You may then configure the TouchPad tapping, buttons, scrolling, pointer motion and sensitivity options to your preferences. You will find further in- formation at www.synaptics.com.
TouchPad Scrolling
This computer model se- ries may feature different
TouchPad versions.
These TouchPads may differ in their vertical scrolling function in most scrollable windows.
Some TouchPads require sliding the finger up and down on the right of the
TouchPad to scroll the window. Other versions require tapping/holding down the finger at the top right or bottom right of the
TouchPad to scroll the window.
Figure 2 - 7
Mouse Properties
2
Touchpad Configuration 2 - 43
2
Storage Devices, Mouse, & Audio
Show Video
Gestures and Device Settings
The Synaptics Gestures Suite application allows you to use a specific gesture (ac- tion) on the surface of the Touchpad to perform specific actions to manipulate doc- uments, objects and applications.
You can get a clearer view of the gestures in- volved by clicking the
Show Video option for each gesture item.
You can configure the settings from the Device Settings tab in Mouse Properties :
1. Go to the Control Panel .
2. Click Mouse ( Hardware and Sound ).
3. Click Device Settings (tab) and click Settings .
4. Use the menu tree on the left to access the user configurable settings.
Select the gesture ( Pinch
Zoom, Rotating, Three
Fingers Down and
Three Finger Flick ) in the
Device Settings > Set- tings left tree menu and click the Show Video button to see the demon- stration video.
For more details on any of the gestures see the help in the lower part of the right menu window.
Figure 2 - 8
Mouse Properties -
Device Settings
2 - 12 Touchpad Configuration
Storage Devices, Mouse, & Audio
Disabling the Touchpad
If you need to disable the Touchpad for any reason (e.g. you may find that when us- ing the computer’s internal keyboard you accidentally trigger the Touchpad when resting your wrists or palms on it) you can do so by using Fn + F1 key combination.
You can also set the system to automatically disable the internal Touchpad when an external USB point device (e.g a USB mouse) is attached.
1. Go to the Mouse Properties control panel.
2. Click to select Device Settings (tab).
3. Click to place a check in the “ Disable internal pointing device when external
USB pointing device is attached ” check box.
4. Click OK to save the setting.
Figure 2 - 9
Mouse Properties
(Disable Touchpad)
2
Touchpad Configuration 2 - 13
2
Storage Devices, Mouse, & Audio
PalmChec k™
In order to improve
Clickpad/Touchpad scrolling responsive- ness when using one- finger scrolling, you can adjust the PalmChe ck™ slider towards “Mini- mum” as per your pref- erence.
PalmCheck
™
The PalmCheck™ feature ( Device Settings > Settings > Pointing > Sensitivity ) helps prevent operating the Clickpad/Touchpad by accident, by recognizing when your palm is resting on it or brushing its surface while you are typing.
However bear in mind that adjusting the slider too far toward s “Mini- mum” can turn off Palm-
Check™ altogether.
Figure 2 - 10
PalmCheck ™ Slider
2 - 14 Touchpad Configuration
Storage Devices, Mouse, & Audio
Scrolling
The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the
TouchPad surface and slide both fingers in the direction required (in a straight con- tinuous motion).
Zooming
The Pinch Zoom gesture can be used to perform the same function as a scroll wheel in Windows applications that support CTRL + scroll wheel zoom functionality.
Place two fingers on the TouchPad (for best results use the tips of the fingers) and slide them apart to zoom in, or closer together to zoom out.
Figure 2 - 11
Scrolling Gesture
Figure 2 - 12
Zooming Gesture
2
Touchpad Configuration 2 - 15
2
Storage Devices, Mouse, & Audio
Rotating
Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments.
Place a finger down on the left “target” zone and keep it stationary. Place another finger near the middle of the TouchPad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object.
Figure 2 - 13
Rotating Gesture
Three Finger-Flick/Three Fingers Down (Press)
The Three Finger-Flick gesture may be used to enhance navigation with a variety of applications such as browsing the Internet or scrolling through a photo viewer. The
Three Fingers Down gesture may be used to launch user-selectable applications.
Figure 2 - 14
Flick/Press
Gesture
2 - 16 Touchpad Configuration
Chapter 3: Power Management
Overview
To conserve power, especially when using the battery, your computer power man- agement conserves power by controlling individual components of the computer
(the monitor and hard disk drive) or the whole system. This chapter covers:
•
•
•
•
•
•
The computer uses enhanced power saving techniques to give the operating system
(OS) direct control over the power and thermal states of devices and processors. For example, this enables the OS to set devices into low-power states based on user set- tings and information from applications.
Power Management
OS Note
Power management functions will vary slight- ly depending on your operating system. For more information it is best to refer to the user’s manual of your operat- ing system.
3
Overview 3 - 1
3
Power Management
The Power Sources
Forced Off
If the system “hangs”, and the Ctrl + Alt + Del key combination do esn’t work, press the power button for 4 seconds , or longer, to force the sys- tem to turn itself off.
The computer can be powered by either an AC/DC adapter or a battery pack.
AC/DC Adapter
Use only the AC/DC adapter that comes with your computer. The wrong type of AC/
DC adapter will damage the computer and its components.
1. When first setting up the computer use the following procedure (as to safeguard the computer during shipping, the battery will be locked to not power the system until first connected to the AC/DC adapter and initially set up as below):
• Attach the AC/DC adapter cord to the DC-In jack on the right of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter and leave it there for 6 seconds or longer .
• Remove the adapter cord from the computer’s DC-In jack, and then plug it back in again; the bat- tery will now be unlocked.
2. Raise the lid/LCD to a comfortable viewing angle.
3. Press the power button to turn “On”.
Battery
The battery allows you to use your computer while you are on the road or when an electrical outlet is unavailable. Battery life varies depending on the applications and the configuration you're using. To increase battery life, let the battery discharge completely before recharging
We recommend that you do not remove the battery. For more information on the bat-
“Battery Information” on page 3 - 17
3 - 2 The Power Sources
Power Management
Turning On the Computer
Now you are ready to begin using your computer. To turn it on simply press the pow- er button on the front panel. 3
When the computer is on, you can use the power button as a Stand by/Hibernate/
Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use
Power Options ( Hardware and Sound ) in the Windows control panel to configure this feature.
Power Button as Stand by or Hibernate Button
You can use the OS’s “Power Options” control panel to set the power button to send the system into Stand by or Hibernate mode (see your OS
’s documentation, or “Configuring the Power Butto ns” on page 3 - 9 for details).
Turning On the Computer 3 - 3
3
Power Management
Shutting the Computer Down
Note that you should always shut your computer down by choosing the Shut down command as this will help prevent hard disk or system problems. Use the Power item in the Start Menu and select Shut down . If you want to add Hibernate/Sleep to the Power Menu see
“Adding Hibernate/Sleep to the Power Menu” on page 3 -
10 .
You can also use the context menu (right-click the Start Menu icon or press the
Windows logo + X key combination) to Sign out, Sleep , Hibernate , Shut down , and Restart .
Figure 3 - 1
Shut Down/Restart
3 - 4 Shutting the Computer Down
Power Plans
The computer can be configured to conserve power by means of power plans (Con- trol Panel > Power Options) . You can use (or modify) an existing power plan , or create a new one.
Power Management
Resuming
Operation
The settings may be adjusted to set the display to turn off after a specified time, and to send the computer into Sleep after a period of inactivity.
Click Change plan settings and then click Change advanced power settings to ac- cess further configuration options in Advanced Settings .
See Table 3 - 1, on page 3 - 11 for informa- tion on how to resume from a power-saving state.
Password
It is recommended that you enable a password on system resume in or- der to protect your data.
Figure 3 - 2
Power Plan
Advanced Settings
3
Power Plans 3 - 5
3
Power Management
Each Windows power plan will also adjust the processor performance of your ma- chine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power).
Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is pow- ered from an AC power source. Choose the Power saver (bear in mind that this scheme may slow down the overall performance of the computer in order to save power) for maximum power saving when the computer is battery (DC power) pow- ered.
Figure 3 - 3
Power Plans
Click to Show/Hide additional power plans
3 - 6 Power Plans
Power-Saving States
You can use power-saving states to stop the computer’s operation and restart where you left off. Windows 10 uses the Sleep, Hibernate and Shut Down power-saving states.
Sleep
In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.
The PC wakes from Sleep within seconds and will return you to where you last left off (what was on your desktop) without reopening the application(s) and file(s) you last used.
If your mobile PC in Sleep is running on battery power the system will use only a minimum amount of power. After an extended period the system will save all the information to the hard disk and shut the computer down before the battery becomes depleted.
To add Sleep to the Power Menu see
“Adding Hibernate/Sleep to the Power
Menu” on page 3 - 10
.
Power Management
Wake On LAN
Support
Wake-On-LAN is only supported from Sleep or
Hibernate states in
Windows .
If you require your com- puter to wake up from network activity in Win- dows then make sure that the computer is ei- ther in Sleep or Hiber- nate .
Wake-On-LAN is not supported from Shut- down states in Win- dows.
3
Power-Saving States 3 - 7
3
Power Management
Hibernate
Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hi- bernate will also return you to where you last left off within seconds. You should put your mobile PC into Hibernate if you will not use the computer for a period of time, and will not have the chance to charge the battery. To add Hibernate to the
Power Menu see “Adding Hibernate/Sleep to the Power Menu” on page 3 - 10 .
Shut down
You should Shut down the computer if you plan to install new hardware, plan to be away from the computer for several days, or you do not need it to wake up and run a scheduled task. Returning to full operation from Shut down takes longer than from
Sleep or Hibernate .
Figure 3 - 4
Power Button &
Start Menu Power
3 - 8 Power-Saving States
Configuring the Power Buttons
The power/sleep button ( Fn + F12 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu.
Power Management
Password
Protection
It is recommended that you enable a password on wake up in order to protect your data.
However you can dis- able this setting from the
Power Options menu by clicking Require a password on wakeup in the left menu, and se- lecting the options (click
Change settings that are currently unavail- able ).
Figure 3 - 5
Power Options
Define Power
Buttons
3
Configuring the Power Buttons 3 - 9
3
Power Management
Adding Hibernate/Sleep to the Power Menu
Add Hibernate/Sleep to the Power Menu as follows.
1. Go to the Power Options ( Hardware and Sound ) control panel.
2. Click “ Change settings that are currently unavailable ”
3. Click Choose what the power buttons do .
4. Click to put a check in the Hibernate/Sleep box under Shutdown settings .
5. Click Save Changes and close the control panel.
.
Figure 3 - 6
Power Options
Define Power
Buttons - Shutdown
Settings
3 - 10 Configuring the Power Buttons
Resuming Operation
You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button ( Fn + F12 key combo).
Power Status Icon Color To Resume
Power Off Off Press the Power Button
Sleep
Hibernate
Display Turned Off
Blinking White
Off (battery)
Orange (AC/DC adapter)
White
Press the Power Button
Press the Sleep Button (Fn + F12 Key
Combo)
Press the Power Button
Press a Key or Move the Mouse/Touchpad
Power Button
When the computer is on, you can use the power button as a Sleep/Hibernate/Shut Down hot key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will force the computer to shut down).
Power Management
Table 3 - 1
Resuming
Operation
Closing the Lid
If you have chosen to send the computer to
Sleep when the lid is closed, raising the lid will wake the system up.
3
Configuring the Power Buttons 3 - 11
3
Power Management
Power Conservation
Modes
The Power Saving set- ting will result in maxi- mum power saving, but with the possible loss of some performance.
Power Conservation Modes
This system supports Power Saving power management features that place comput- ers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period of inactivity. Adjust Power Conservation Modes from the Control Center :
1. Press the Fn + Esc key combination to toggle the Control Center on/off.
2. Click either the Performance , Balanced or Power Saving button.
Setting the mode to Bal- ance will give power saving matched with performance.
Performance will give optimum computer per- formance but with less power conservation.
Note that the Energy
Star setting will put the display into sleep after no more than 15 min- utes of user inactivity.
Figure 3 - 7
Control Center
3 - 12 Configuring the Power Buttons
Ctrl + Alt + Delete Key Combination
You can use the CTRL + ALT + DEL key combination from almost any of the Win- dows 10 interfaces/Apps to bring up a full-screen displaying Lock , Switch User ,
Sign out, Change a password and Task Manager options. If you click the Power icon in the lower right corner of the screen a power management option menu ap- pears to display Sleep , Shut down , and Restart .
Power Management
3
Figure 3 - 8
Ctrl + Alt + Delete
Menu
To fully control all the power options (including Hibernate mode) go to the Power
Options control panel and configure the power button, sleep button and lid to per- form the function selected.
Configuring the Power Buttons 3 - 13
3
Power Management
Settings Menu Power Controls
The Settings item in the Start Menu (or via the Action Center ) gives you access to a number of power settings control panels which enable you to quickly adjust power options. Click System to access the menu including the power option settings.
Figure 3 - 9
Settings
3 - 14 Settings Menu Power Controls
Battery Saver
Battery in Settings will display the battery level, and by clicking Battery usage by app you can see the current state of battery usage by application etc. The Battery saver can be level can be adjusted to be turned on if the battery level falls below a certain level to limit background activity and push notifications.
Power Management
Figure 3 - 10
Settings > Battery >
Battery Saver
3
Settings Menu Power Controls 3 - 15
3
Power Management
Power & Sleep
Power & sleep gives you quick access to Screen and Sleep settings. Click Addi- tional power settings to go to the main power options control panel.
Figure 3 - 11
Settings > Power &
Sleep
3 - 16 Settings Menu Power Controls
Battery Information
Follow these simple guidelines to get the best use out of your battery.
Battery Power
Your computer’s battery power is dependent upon many factors, including the pro- grams you are running, and peripheral devices attached. You can set actions to be taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from power plan Change plan settings > Change advanced power settings (see Figure
3 - 3 on page 3 - 6 ).
Click the battery icon in the notification area to see the current battery level and charge status (you can also click Power & sleep settings to access the Settings menu to quickly adjust power settings).
Power Management
Low Battery
Warning
When the battery is criti- cally low, immediately connect the AC/DC adapter to the computer or save your work, oth- erwise, the unsaved data will be lost when the power is depleted.
Figure 3 - 12
Battery Icon
(Notification Area) &
Battery Advanced
Settings
3
Battery Information 3 - 17
3
Power Management
Windows Mobility
Center
The Windows Mobility
Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc.
Conserving Battery Power
• Use a power plan that conserves power (e.g Power saver ), however note that this may have an affect on computer performance.
•
Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter.
• Reduce the amount of time before the display is turned off.
•
Close wireless, Bluetooth, modem or communication applications when they are not being used.
•
Disconnect/remove any unnecessary external devices e.g. USB devices,
ExpressCards etc.
Figure 3 - 13
Windows Mobility
Center
(Control Panel)
3 - 18 Battery Information
Battery Life
Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days .
Power Management
Battery Removal
We should not remove the built-in battery yourself (see sidebar).
Note that the built-in battery is not user re- movable . Removing the battery will violate the terms of your warranty.
New Battery
Recharging the Battery with the AC/DC Adapter
If you need to remove the battery for any rea- son, please contact your distributor/supplier for further information.
The battery pack automatically recharges when the AC/DC adapter is attached and plugged into an electrical outlet. If the computer is powered on, and in use, it will take several hours to fully recharge the battery. When the computer is turned off but
plugged into an electrical outlet, battery charge time is less. Refer to
“LED Indica- tors” on page 1 - 7
for information on the battery charge status, and to
FAQ” on page 3 - 21 for more information on how to maintain and properly re-
charge the battery pack.
3
Battery Information 3 - 19
3
Power Management
Caution
Danger of explosion if battery is incorrectly re- placed.
Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacture r’s in- structions.
Proper handling of the Battery Pack
• DO NOT disassemble the battery pack under any circumstances
•
DO NOT expose the battery to fire or high temperatures, it may explode
•
DO NOT connect the metal terminals (+, -) to each other
Damaged Battery Warning
Should you notice any physical defects (e.g. the battery is bent out of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your distributor/supplier. If the battery has been dropped we do not recommend using it any further, as even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire. It is recommended that you replace your computer battery every two years.
3 - 20 Battery Information
Battery FAQ
How do I completely discharge the battery?
Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own.
1. Save and close all files and applications.
2. Create a power plan for discharging the battery and set all the options to Never .
Power Management
Figure 3 - 14
Power Plan Create
3
Battery Information 3 - 21
3
Power Management
3. Click Change plan settings (after creating it) and click Change plan settings >
Change advanced power settings .
Figure 3 - 15
Change Plan
Settings / Change
Advanced Power
Settings
3 - 22 Battery Information
4. Scroll down to Battery and click + to expand the battery options.
5. Choose the options below (click Yes if a warning appears):
Power Management
Figure 3 - 16
Power Options
Advanced Settings -
Battery
3
•
Low battery levels = 0%
•
Critical battery Levels = 1%
• Low battery action = Do Nothing
•
Critical battery action (On battery) = Shut Down
•
Critical battery action (Plugged in) = Do Nothing
Battery Information 3 - 23
3
Power Management
How do I fully charge the battery?
When charging the battery, don’t stop until the LED charging indicator light changes from orange to green.
How do I maintain the battery?
Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
3 - 24 Battery Information
Removing the Battery
It is possible to remove the battery from the computer, however we recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason (e.g. long term storage) see below.
1. Turn the computer off , and turn it over.
2. Slide the latch
3. Slide the latch
1
2 in the direction of the arrow. in the direction of the arrow, and hold it in place.
4. Slide the battery out in the direction of the arrow 3 .
5. Reinsert the battery as illustrated below 4 .
6. Make sure the latches are returned to the lock position 5 .
1
2 3
Power Management
Bottom Cover
Removal Warning
Do not remove any cov- er(s) and /or screw(s) for the purposes of device upgrade as this may violate the terms of your warranty.
If you need to replace/ remove the hard disk/
RAM/optical device etc., for any reason, please contact your distributor/ supplier for further infor- mation.
4
5
Figure 3 - 17
Battery Removal and Insertion
5
3
Removing the Battery 3 - 25
3
Power Management
3 - 26
Chapter 4: Drivers & Utilities
This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available op- erating systems haven’t built in drivers and utilities. Thus, some of the system com- ponents won’t be auto-configured with an appropriate driver or utility during operating system installation. Instead, you need to manually install some system-re- quired drivers and utilities.
What to Install
The
Device Drivers & Utilities + User’s Manual
disc contains the drivers and util- ities necessary for the proper operation of the computer. Table 4 - 1, on page 4 - 4 lists what you need to install and it is very important that the drivers are installed by the method outlined in this chapter, and in the order indicated . Note that the information on the following pages is for Windows 10 (64-bit) only .
Module Driver Installation
The procedures for installing drivers for the Wireless LAN , Bluetooth & WLAN
Combo, Intel Technology and 4G
modules are provided in “Modules” on page 6 -
Drivers & Utilities
Driver Installation &
Power
When installing driv- ers make sure your
4 computer is powered by the AC/DC adapter connected to a work- ing power source .
Some drivers draw a significant amount of power during the instal- lation procedure, and if the remaining battery capacity is not adequate this may cause the sys- tem to shut down and cause system problems
(note that there is no safety issue involved here, and the battery will be rechargeable within 1 minute).
What to Install 4 - 1
4
Drivers & Utilities
Driver Installation
1. Insert the Device Drivers & Utilities + User ’s Manual disc into the DVD drive.
2. Click the message “ Tap to choose what happens with this disc .”
3. Click Run autorun.exe
.
4. Click Install Drivers (button), or Option Drivers (button) to access the Optional driver menu.
Figure 4 - 1 - Drivers Installer Screen 1
4 - 2 Driver Installation
Drivers & Utilities
5. Check the driver installation order from Table 4 - 1, on page 4 - 4 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below.
6. Click to select the driver you wish to install, (you should note down the drivers as you install them).
7. Follow the instructions for each individual driver installation procedure as listed on the following pages.
Figure 4 - 2 - Install Drivers
4
Driver Installation 4 - 3
4
Drivers & Utilities
Win 10 (64-bit) Driver
Page #
Win 10 (64-bit) - Optional Items
Intel® Rapid Storage Technology
PC Camera (no driver installation required)
Trusted Platform Module (no driver installation required)
3G/4G Module (no driver installation required)
Page #
All drivers provided are for the Windows 10 (64-bit) operating system.
Table 4 - 1 - Driver Installation
Note that you need to install both the WLAN & Bluetooth drivers for the WLAN & Bluetooth Combo modules.
4 - 4 Driver Installation
Drivers & Utilities
Manual Driver Installation
Updating/Reinstalling Individual Drivers
Click Browse CD/DVD (button) in the Drivers Install- er application and browse to the executable file in the appropriate driver folder.
If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do
Windows Update this go to the Control Panel in the Windows OS and double-click the Programs icon ( Programs > Uninstall a program ). Click to select the driver (if it is not listed see below) and click Uninstall , and then follow
4
After installing all the drivers make sure you enable
Check for updates ( Settings > Update & security >
Check for updates ) in order to get all the latest secu- rity updates etc. (all updates will include the latest hot- fixes from Microsoft). See
“Windows Update” on page 4 - 9 for instructions. the on screen prompts (it may be necessary to restart the computer). Reinstall the driver as outlined in this chapter.
If the driver is not listed in the Programs and Fea- tures menu:
1. Go to the Control Panel ).
2. Double-click Device Manager ( Hardware and
Sound > Devices and Printers > Device
Manager ).
3. Double-click the device you wish to update/reinstall the driver for (you may need to click “+” to expand the selection).
4. Click Driver (tab) and click the Update Driver or
Uninstall button and follow the on screen prompts.
Driver Installation 4 - 5
4
Drivers & Utilities
User Account Control
If a User Account Control prompt appears as part of the driver installation procedure, click Continue or
Allow , and follow the installation procedure as direct- ed.
Windows Security Message
If you receive a Windows security message as part of the driver installation process. Just click “Install this driver software anyway” or
“Install” to continue the installation procedure.
You will receive this message in cases where the driv- er has been released after the version of Windows you are currently using. All the drivers provided will have already received certification for Windows .
New Hardware Found
If you see the message “ New Hardware Found ” dur- ing the installation procedure ( other than when out- lined in the driver install procedure ), click Cancel to close the window, and follow the installation proce- dure.
Driver Installation General Guidelines
The driver installation procedure outlined in this Chapter
(and in Chapter 7 Options & Modules ), are accurate at the time of going to press.
Drivers are always subject to upgrade and revision so the exact procedure for certain drivers may differ slight- ly. As a general guide follow the default on screen in- structions for each driver (e.g. Next > Next > Finish ) unless you are an advanced user. In many cases a re- start is required to install the driver.
Make sure any modules (e.g. WLAN or Bluetooth) are
ON (i.e. the system is not in Airplane Mode) before installing the appropriate driver.
4 - 6 Driver Installation
Driver Installation Procedure
Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button).
Chipset
1.
Click 1.Install Chipset Driver > Yes .
2.
Click Next > Accept > Install .
3.
Click Restart Now to restart the computer.
Video (VGA)
1.
Click 2.Install VGA Driver > Yes .
2.
Click Next > Yes > Next > Next .
3.
Click Finish to restart the computer.
Drivers & Utilities
LAN
Note: If the computer enters a deep sleep mode during installation, you will be prompted to plug in a network cable, and click OK , to continue installation. If a net- work cable is not available, restart the system and reinstall the LAN driver.
4
1.
Click 3.Install LAN Driver > Yes .
2.
Click Next > Install .
3.
Click Finish .
Card Reader
1.
Click 4.Install Cardreader Driver > Yes .
2.
Click Finish .
Touchpad
1.
Click 5.Install Touchpad Driver > Yes .
2.
Click Next .
3.
Click the button to accept the license, and then click Next .
4.
Click Finish > Restart Now to restart the com- puter.
Driver Installation 4 - 7
4
Drivers & Utilities
Control Center
1.
Click 6.Install Control Center AP > Yes .
2.
Click Next > Install .
3.
Click Finish to restart your computer (see
Appendix B
after restart you will be required to save your keyboard type ) .
Airplane
Note: Do not use Update Driver in Device Manager to install the Airplane Mode driver.
1.
Click 7.Install Airplane Driver > Yes .
2.
Click Next > Install .
3.
Click Finish to restart the computer.
MEI Driver
1.
Click 8.Install MEI Driver > Yes .
2.
Click Next .
3.
Click the check box to accept the license and then click Next .
4.
Click Next .
5.
Click Finish .
Audio
1.
Click 10.Install Audio Driver > Yes .
2.
Click Next .
3.
Click Finish to restart the computer.
Note that after installing the audio driver the system will not return to the Drivers Installer screen. To in- stall any of the optional drivers listed overleaf, eject the Device Drivers & Utilities + User’s Manual disc and then reinsert it (or double-click the disc icon in My
Computer ), and click Option Drivers (button) to ac- cess the optional driver menu.
It is recommended that you install the Intel Rapid
Storage Technology
driver (see “Intel® Rapid Stor- age Technology” on page 6 - 13 ).
4 - 8 Driver Installation
Windows Update
After installing all the drivers make sure you enable Win- dows Update in order to get all the latest security up- dates etc (all updates will include the latest hotfixes from Microsoft).
To enable Windows Update make sure you are con- nected to the internet :
1. Go to the Control Panel .
2. Click Windows Update (System and Security/
Security).
3. Click Check for updates (button).
4. The computer will now check for updates (you need to be connected to the internet).
5. Click Install now (button) to begin checking for the updates.
6. Click Install updates (button) to install the updates.
Drivers & Utilities
Optional Drivers
See the pages indicated in Table 4 - 1, on page 4 - 4 for the driver installation procedures for any modules included in your purchase option.
4
Figure 4 - 3 - Optional Drivers Installer Screen
Note that you need to install both the WLAN & Blue- tooth drivers for the WLAN & Bluetooth Combo modules.
Driver Installation 4 - 9
4
Drivers & Utilities
4 - 10
Chapter 5: BIOS Utilities
Overview
This chapter gives a brief introduction to the computer’s built-in software:
Diagnostics: The POST (Power-On Self Test)
Configuration: The Setup utility
If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup . Even if you are a beginner, keep a record of the set- tings you find and any changes you make. This information could be useful if your system ever needs servicing.
There is one general rule: Don’t make any changes unless you are sure of what you are doing . Many of the settings are required by the system, and changing them could cause it to become unstable or worse. If you have any doubts, consult your service representative.
BIOS Utilities
BIOS Screens
Note that the BIOS screens pictured on these pages are intend- ed for guidance in setting up your s ystem’s 5
BIOS.
BIOS versions are sub- ject to constant change and revision, therefore your comp uter’s actual screens may appear slightly different from those pictured on these pages.
Overview 5 - 1
5
BIOS Utilities
BIOS Settings
Warning
Incorrect settings can cause your system to malfunction. To correct mistakes, return to Setup and restore the Optimized Defaults with
<F3> .
UEFI Boot & POST
The Power-On Self Test (POST)
If you enable the Boot-time Diagnostic Screen in the Setup Utility, each time you turn on the computer the system takes a few seconds to conduct a POST , including a quick test of the on-board RAM (memory).
As the POST proceeds, the computer will tell you if there is anything wrong. If there is a problem that prevents the system from booting, it will display a system summary and prompt you to run Setup .
If there are no problems, the Setup prompt will disappear and the system will load the operating system. Once that starts, you can’t get into Setup without rebooting.
When UEFI Boot is en- abled, then the prompts to press F2 or F7 will not appear . However you can still press F2 to enter the setup, or F7 to choose the preferred boot device, if you press the key immediately the system boots up.
5 - 2 The Power-On Self Test (POST)
BIOS Utilities
Failing the POST
Errors can be detected during the POST . There are two categories, “fatal” and “non- fatal”.
Fatal Errors
These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized distributor/supplier as soon as possible.
5
Non-Fatal Errors
This kind of error still allows you to boot. You will get a message identifying the problem (make a note of this message!) and you can then press F7 (the F7 on screen will be highlighted to illustrate that the system is processing the request) for boot op- tions.
Press F2 (give the system a few seconds to enter Setup ; the F2 on screen will be highlighted to illustrate that the system is processing the request) to run the Setup program and try to correct the problem. If you still get an error message after you change the setting, or if the “cure” seems even worse, call for help.
The Power-On Self Test (POST) 5 - 3
BIOS Utilities
BIOS Settings
Warning
Incorrect settings can cause your system to malfunction. To correct
5 mistakes, return to Setup and restore the Optimized Defaults with
<F3> .
The Setup Utility
The Aptio Setup Utility tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration).
Entering Setup
To enter Setup , turn on the computer and press F2 (give the system a few seconds to enter Setup ; the F2 on screen will be highlighted to illustrate that the system is processing the request) during the POST (or press F7 for boot options). If you get a
“Keyboard Error”, (usually because you pressed
F2 too quickly) just press F2 again.
If the computer is already on, reboot using the Ctrl + Alt + Delete combination and then hold down F2 when prompted. The Setup main menu will appear.
To see the boot options press F7.
5 - 4 The Setup Utility
Setup Screens
The following pages contain additional advice on portions of the Setup . Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make chang- es to Setup .
Instructions on how to navigate each screen are in the box at the bottom right side of the screen.
BIOS Utilities
Setup Menus
The Setup menus shown in this section are for reference only. Your computer’s menus will indicate the configura-
5 tion appropriate for your model and options.
Figure 5 - 1
Navigation Menu
If these tools are confusing, press F1 to call up a General Help screen, and then use the arrow keys to scroll up or down the page.
The Item Specific Help on the upper right side of each screen explains the highlight- ed item and has useful messages about its options.
If you see an arrow next to an item, press Enter to go to a sub-menu on that sub- ject. The sub-menu screen that appears has a similar layout, but the Enter key may execute a command.
The Setup Utility 5 - 5
5
BIOS Utilities
Figure 5 - 2
Main Menu
Main Menu
5 - 6 Main Menu
System Time & Date (Main Menu)
The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes.
SATA Port # (Main Menu)
Pressing Enter opens the sub-menu to show the configuration of a optical Device/
HDD on the computer’s SATA Ports.
OffBoard SATA/NVme Controller Configuration (Main Menu)
Pressing Enter opens the sub-menu to show the configuration of any devices on the off board SATA/NVme Controller if applicable.
CPU/ ME FW Version / System/ Extended Memory: (Main Menu)
This item contains information on the CPU type and system memory, and is not user configurable. The system will auto detect the amount of memory installed.
MB Series / BIOS Revision / KBC/EC firmware Revision / Mac Address (Main
Menu)
This item contains information on the BIOS version etc., and is not user configu- rable.
BIOS Utilities
5
Main Menu 5 - 7
5
BIOS Utilities
Figure 5 - 3
Advanced Menu
Advanced Menu
Advanced Chipset Control (Advanced Menu)
The sub-menu here allows you to enable/disable FlexiCharger .
5 - 18 Advanced Menu
FlexiCharger (Advanced Menu > Advanced Chipset Control)
The sub-menu here allows you to enable/disable the FlexiCharger . The FlexiCharg- er may be set to automatically start charging your battery when the battery reaches a certain capacity level (e.g. you could start the battery charge level at 40%).
See the sidebar warning for information on running the FlexiCharger for an ex- tended period as this is not recommended .
BIOS Utilities
FlexiCharger
Warning
If you leave the FlexiCh- arger continuously " En- abled
” for a period of three months or more, the battery meter's read-
5 ing accuracy will deteri- orate.
To reset this, set the
FlexiCharger to " Dis- abled ", and then allow the battery to completely
before enabling the function again.
Figure 5 - 4
Advanced Chipset
Control >
FlexiCharger
Advanced Menu 5 - 9
5
BIOS Utilities
SATA Mode (Advanced Menu)
The SATA (Serial ATA) controller operates in AHCI (Advanced Host Controller
Interface) mode. Install the Intel Rapid Storage Technology driver to support your
drive in AHCI mode (see “Intel® Rapid Storage Technology” on page 6 - 13 ).
Boot Logo (Advanced Menu)
Use this menu item to enable/disable the Boot Logo screen at system startup if you have not enabled UEFI Boot . If you disable the Boot Logo you will not see the F2
Enter Setup or F7 Boot Options prompts on the screen, however you can still press these keys, while the boot screen is displayed, to perform the Enter Setup or Boot
Option functions.
Power On Boot Beep (Advanced Menu)
Use this menu item to enable/disable the beep as the computer starts up.
Battery Low Alarm Beep (Advanced Menu)
Use this menu item to enable/disable the battery low alarm beep.
5 - 20 Advanced Menu
Security Menu
BIOS Utilities
Security Menu
The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on.
5
These settings do not affect your machine or network passwords which will be set in your software OS.
Figure 5 - 5
Security Menu
Set Supervisor Password (Security Menu)
You can set a password for access to the Aptio Setup Utility . This will not affect access to the computer OS (only the Aptio Setup Utility ).
Security Menu 5 - 11
5
BIOS Utilities
Password Warning
If you set a boot pass- word (Password on boot is “Enabled“), NEVER forget your password.
The consequences of this could be serious. If you cannot remember your boot password you must contact your ven- dor and you may lose all of the information on your hard disk.
Note : To clear existing passwords press Enter and type the existing password, then press Enter for the new password (without typing any password entry) and Enter again to confirm the password clearance.
Note : You can only set the user password after you have set the supervisor pass- word.
Set User Password (Security Menu)
You can set a password for user mode access to the Aptio Setup Utility . This will not affect access to the computer OS, (only the Setup utility) unless you choose to set a Password on Boot (see below). Many menu items in the Aptio Setup Utility cannot be modified in user mode.
Note : You can only set the user password after you have set the supervisor pass- word.
Password on boot: (Security Menu)
Specify whether or not a password should be entered to boot the computer ( you may only set a password on boot if a supervisor password is enabled ). If “ Enabled ” is selected, only users who enter a correct password can boot the system ( see the warning in the sidebar ). The default setting is “ Disabled
”.
5 - 12 Security Menu
Secure Boot Control (Security Menu)
Secure Boot Control prevents unauthorized operating systems and software from loading during the startup process. Secure Boot is available as a menu option if you have enabled UEFI Boot
(see “Boot Menu” on page 5 - 15 ). Enabling Secure Boot
will bring up the Secure Boot Mode menu to enable you to configure Secure Boot as Standard (with a fixed secure boot policy), or Custom (which enables you to make changes to the Key Management database).
BIOS Utilities
Figure 5 - 6
Security -
Secure Boot
(Key Management)
5
Security Menu 5 - 13
5
BIOS Utilities
Figure 5 - 7
Security Device
Support
TPM Configuration (Security Menu)
This sub-menu will allow you to enable/disable Trusted Platform Module (TPM) support, and to configure the TPM State. Select TPM Configuration and press En- ter to access the sub-menu. Press Enter to access the Security Device Support menu and select Enable to support TPM. You can select Pending operation , and then se- lect TPM clear to clear existing TPM information in order to reset the TPM (see
“Trusted Platform Module” on page 6 - 20 for details).
5 - 14 Security Menu
Boot Menu
When you turn the computer on it will look for an operating system (e.g. Windows
7 ) from the devices listed in this menu, and in this priority order . If it cannot find the operating system on that device, it will try to load it from the next device in the order specified in the Boot Option Priorities .
BIOS Utilities
Figure 5 - 8
Boot Menu
BIOS Screens
Note that the BIOS screens pictured on these pages are intend- ed for guidance in set- ting up your s ystem’s
BIOS.
BIOS versions are sub- ject to constant change and revision, therefore your comp uter’s actual screens may appear slightly different from those pictured on these pages.
5
Boot Menu 5 - 15
BIOS Utilities
UEFI Boot
UEFI Boot is “ Enabled ” for your system by de- fault.
5
It is recommended that you keep UEFI Boot en- abled for the Windows
10/ Windows 8.1/ Win- dows 8 operating sys- tems, however if you are running the Windows 7
OS then you should set
UEFI Boot to
“
Disabled
”
(for other operating sys- tems please check the
OS’s documentation).
Boot Option Priorities (Boot Menu)
Press Enter to select the Boot Option # and use the arrow keys to select any device in order to move its boot priority up and down the list (the selected device will be highlighted in white).
UEFI Boot (Boot Menu)
Enable/disable UEFI Boot from this menu. The Unified Extensible Firmware Inter- face (UEFI) specification provides a clean interface between operating systems and platform firmware at boot time. In contrast to BIOS, UEFI defines a set of standard boot and runtime services. The Network Stack item will be enabled as an option un- der UEFI Boot.
UEFI Boot is enabled for your system by default. It is recommended that you keep UEFI Boot enabled for the Windows operating system.
5 - 16 Boot Menu
Exit Menu
BIOS Utilities
Figure 5 - 9
Exit Menu
5
Click Save Changes and Reset to save all changes made. Choosing to Discard
Changes , or Exit Discarding Changes , will wipe out any changes you have made to the Setup . You can also choose to restore the original Setup defaults that will re- turn the Setup to its original state, and erase any previous changes you have made in a previous session.
Exit Menu 5 - 17
5
BIOS Utilities
5 - 18
Modules
Chapter 6: Modules
Overview
This chapter contains the information on the various modules (some of which are optional ) which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative.
The chapter includes information on the following:
•
•
•
Intel® Rapid Storage Technology
•
•
•
Overview 6 -
19
Modules
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Make sure the WLAN &
6
Bluetooth module(s) are OFF if you are using the computer aboard aircraft by putting the system in to Airplane
Mode
(see Table 1 - 3, on page 1 - 12 ).
Wireless LAN Module
If you have included an Intel ® or 3rd Party 802.11b/g/n (Combo) module is on
(i.e. the system is not in Airplane Mode ) before installing the driver.
Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 4 .
Note that you need to install both the WLAN & Bluetooth drivers for the WLAN
& Bluetooth Combo modules.
See the appropriate driver installation instructions on the page indicated below:
•
“3rd Party 802.11b/g/n Driver Installation” on page 6 - 3
•
“Intel® WLAN Driver Installation” on page 6 - 3
6 - 2 Wireless LAN Module
3rd Party 802.11b/g/n Driver Installation
1.
Make sure the system is not in Airplane Mode , and then insert the
Device
Drivers & Utilities + User’s Manual
disc into the DVD drive.
2.
Click Option Drivers (button).
3.
Click 1.Install WLAN Driver > Yes .
4.
Click Next .
5.
Click Finish to restart the computer.
6.
The operating system is the default setting for Wireless LAN control in
Windows
6 - 4
Intel® WLAN Driver Installation
1.
Make sure the system is not in Airplane Mode , and then insert the
Device
Drivers & Utilities + User’s Manual
disc into the DVD drive.
2.
Click Option Drivers (button).
3.
Click 1.Install WLAN Driver > Yes .
4.
Click in the check box to agree to the End User License Agreement and click
Install .
5.
Click Finish .
6.
The operating system is the default setting for Wireless LAN control in
Windows
6 - 4
Modules
Wireless LAN Module 6 - 3
6
Modules
6
Figure 6 - 1
WiFi & Network
Connections
WLAN Configuration in Windows
You can configure a wireless connection using one of the following options, how- ever make sure the Wireless LAN module is turned on (and not in Airplane Mode) before configuration begins.
1. Click the Wireless icon in the notification area of the taskbar.
2. Make sure that Airplane mode is off (the Airplane mode icon should be gray).
3. A list of available access points will appear.
4. Double-click an access point to connect to it (or click it and click Connect ).
6 - 4 Wireless LAN Module
5. Enter a network security key (password) if required, and click Next .
6. You can choose to share or connect to devices or not.
7. When you are connected to the network access point it will display Connected status .
8. Select any connected network and click Disconnect from a connected access point.
to disconnect
Wireless Device
Operation Aboard Aircraft
The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Make sure the module is either OFF or in Airplane mode if you are using the computer aboard aircraft.
Modules
Figure 6 - 2
Network Connected
(Click Disconnect)
6
Wireless LAN Module 6 - 5
6
Modules
Figure 6 - 3
Network & Internet
Settings
9. You can click the Airplane Mode button to turn the mode On or Off.
10. You need to either use Airplane Mode , or turn the WLAN module off aboard aircraft.
11. Network & Internet in Windows Settings will bring up a more comprehensive list of network and internet settings including Wi-Fi (can be turned on/off), Airplane mode (Airplane mode and Wireless devices can be turned on/off) VPN , Dial-up ,
Ethernet and Proxy .
6 - 6 Wireless LAN Module
Bluetooth & WLAN Combo Module
If your purchase option includes the Combination Wireless LAN & Bluetooth module (either
Intel® or 3rd Party module
) then install the driver as instructed on the following pages.
Make sure that the module is on (i.e. the system is not in Airplane Mode ) before in- stalling the driver.
Bluetooth Data Transfer
Note that the transfer of data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not supported). Therefore if you are copying a file from your computer to a Bluetooth enabled device, you will not be able to copy a file from the Bluetooth enabled device to your computer until the file transfer process from the computer has been completed.
Note that you need to install both the WLAN & Bluetooth drivers for the WLAN
& Bluetooth Combo modules.
Modules
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Make sure the WLAN &
Bluetooth module(s) are OFF if you are using the computer aboard aircraft by putting the system in to Airplane
Mode
(see Table 1 - 3, on page 1 - 12 ).
6
Bluetooth & WLAN Combo Module 6 - 7
Modules
6
3rd Party Bluetooth (V4.0) Combo Driver Installation
1.
Make sure the system is not in Airplane Mode , and then insert the
Device
Drivers & Utilities + User’s Manual
disc into the DVD drive.
2.
Click Option Drivers (button).
3.
Click 2.Install Combo BT Driver > Yes .
4.
Click Next .
5.
Click Finish to restart the computer.
6.
“Bluetooth Configuration in Windows” on page 6 - 9
tion instructions.
Intel Bluetooth Combo Driver Installation
1.
Make sure the system is not in Airplane Mode , and then insert the
Device
Drivers & Utilities + User’s Manual
disc into the DVD drive.
2.
Click Option Drivers (button).
3.
Click 2.Install Combo BT Driver > Yes .
4.
Click Next > Next .
5.
Click in the check box to accept the license and click Next .
6.
Select the setup type ( Typical is recommended) and click Install .
7.
Click Finish .
8.
“Bluetooth Configuration in Windows” on page 6 - 9
tion instructions.
6 - 8 Bluetooth & WLAN Combo Module
Bluetooth Configuration in Windows
1. Go to the Settings control panel and click Devices (or click the Bluetooth icon in the taskbar and click Add a Bluetooth Device ).
2. Click Bluetooth & other devices and make sure Bluetooth is On.
3. Click Add Bluetooth or other device > Bluetooth (Add a device) and a list of discovered devices will appear.
Modules
Figure 6 - 4
Settings > Bluetooth
& Other Devices
(Add a Bluetooth
Device)
Figure 6 - 5
Add a Device
6
Bluetooth & WLAN Combo Module 6 - 9
Modules
6
Figure 6 - 6
Bluetooth Connect
4. Double-click the device you want to pair with the computer and click Connect, if the PIN matches that on the device to which you wish to connect (you may need to click paid on the device) .
6 - 10 Bluetooth & WLAN Combo Module
5. Select a device and click Remove Device any device (click Yes to confirm). to disconnect from
Modules
Figure 6 - 7
Bluetooth Remove
Device
6
Bluetooth & WLAN Combo Module 6 - 11
Modules
6
Figure 6 - 8
Bluetooth Settings
To Make your Computer Discoverable to Bluetooth Devices
1. Go to the Settings control panel and click Devices (or click the Bluetooth icon in the taskbar and click Open Settings ).
2. Click Bluetooth & other devices and click More Bluetooth options.
3. In Bluetooth Settings make sure that Allow Bluetooth devices to find this PC check box ( Discovery ) has a check inside it.
4. Make sure that the Alert me when a new Bluetooth device wants to connect check box ( Notifications ) has a check inside it, if you want to be notified when a
Bluetooth device wants to connect.
6 - 12 Bluetooth & WLAN Combo Module
Intel ® Rapid Storage Technology
The Intel Rapid Storage Technology application provides high-performance
SATA and SATA RAID capabilities. Install the Intel Rapid Storage Technology application (after installing all necessary drivers in the correct order) to support your RAID system in AHCI mode
in the BIOS (see “SATA Mode (Advanced
IRST Driver Installation
1.
Insert the
Device Drivers & Utilities + User’s Manual
disc into the DVD drive.
2.
Click Option Drivers (button).
3.
Click 3.Install IRST Driver > Yes .
4.
Click Next .
5.
Click the check box to accept the license and click Next.
6.
Click Next > Next > Next .
7.
Click Finish to restart the computer.
Modules
6
Intel® Rapid Storage Technology 6 - 13
Modules
6
PC Camera
Use the Fn + F10
key combination (see “Function Keys & Visual Indicators” on page 1 - 12 ) or
Control Center button to toggle power to the PC Camera module.
When the PC Camera is in use the LED indicator to the left of the camera will be illuminated (see
2 Figure 1 - 2 on page 1 - 6 ).
Note that you need to use the Camera app in Windows to take pictures and cap- ture video.
6 - 14 PC Camera
Camera App
1. Make sure the PC Camera is turned on by using the Fn + F10 key combination (or
Control Center button ).
2. Run the Camera app from the Start menu by clicking on the Camera app icon
(you can type “camera” into the search box to find the Camera app).
3. The interface displays two buttons on the right of the screen; one for photo and one for video.
Photo Video
4. Simply click on the appropriate button to switch to either photo or video modes.
5. You can use the buttons at the top of the screen to access the Settings and Auto/
Pro menus (for Self Timer or Exposure compensation ).
Modules
Figure 6 - 9
Camera App Mode
Icons
Figure 6 - 10
Camera Menu
Buttons
6
PC Camera 6 - 15
6
Modules
Figure 6 - 11
Camera Settings
6. Click Settings to access the camera settings menu to make adjustments for
Camera press and hold button , photo Aspect ratio, Framing grid , Time lapse, video recording frame rates and Flicker reduction .
Camera Settings
The Self Timer can be set to take Photos after 2 , 5 or 10 seconds and can also be set to continue taking pictures until the camera button is pressed again ( Photo Burst ).
The Aspect Ratio can be changed to those the system supports.
You can use a Framing grid to help you line up pictures.
Time lapse can be set to keep taking photos until the camera but- ton is pressed again.
The Video recording resolution and frame rate can be set to any supported by the system. Note that capturing high resolution vid- eo files requires a substantial amount of disk space for each file.
After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to File Explorer, right-click the hard disk, and select Prop- erties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
If you need to reduce any screen flicker, change the settings in
Flicker reduction to either e.g. 50Hz or 60Hz.
6 - 16 PC Camera
7. With the Pro menu expanded you can access the Exposure compensation button to adjust the brightness.
Modules
Figure 6 - 12
Camera Brightness
Adjustment
6
PC Camera 6 - 17
6
Modules
Figure 6 - 13
Video Camera
Recording in
Process
Taking Pictures/Capturing Video
1. Make sure the PC Camera is turned on by using the Fn + F10 key combination (or
Control Center button ).
2. Run the Camera app from the Start menu by clicking on the Camera app icon
(you can type “camera” into the search box to find the Camera app).
3. Click to select either photo or video modes.
4. Click the photo icon to take a picture.
5. Click on the video icon to start video capture (when video capture begins a timer will appear at the bottom of the screen).
6. To stop video capture click the stop button (you can also pause the video capture).
6 - 18 PC Camera
7. Captured photos and videos will be saved to the Photos app stored in the Start menu (type Photos into the search box if you cannot find the app) . You can also access the photos from the Camera roll icon at the bottom right of the Camera app screen.
Modules
Figure 6 - 14
Photos App (For
Captured Photos
& Videos)
&
Camera Roll in the
Camera App
6
PC Camera 6 - 19
6
Modules
Trusted Platform Module
( Optional )
The TPM security chip allows you to create and manage digital certificates for user and platform authentication. This type of security is usually administered within large enterprises and organizations, and therefore requires implementation by a sys- tem administrator before users can access security features.
Individual users can use the TPM as an authentication with the fingerprint reader.
Make sure you have administrator’s rights to your computer, and have a Windows password enabled for full security protection. In addition Make sure you prepare a removable media (e.g. a USB flash drive) to store passwords etc. before begin- ning the TPM initialization process .
Before setting up the TPM functions you must initialize the security platform.
6 - 20 Trusted Platform Module
Enabling & Managing TPM
1. Restart the computer.
2. Enter the Aptio Setup Utility pressing F2 during the POST/startup.
3. Use the arrow keys to select the Security menu.
4. Select TPM Configuration and press Enter to access the sub-menu.
5. Press Enter to access the Security Device Support menu and select Enable .
6. Press F4 to save the changes and restart the computer.
7. You can now manage the TPM from Windows .
Modules
Clearing TPM
Information
You can select Pend- ing operation , and then select TPM clear to clear existing TPM information in order to reset the TPM. 6
Figure 6 - 15
TPM State (Enable)
Trusted Platform Module 6 - 21
6
Modules
Figure 6 - 16
BitLocker Drive
Encryption
(TPM
Administration)
TPM Management in Windows
You can manage your TPM settings from within Windows :
1. Go to the Control Panel .
2. Click BitLocker Drive Encryption ( System and Security ).
3. Click TPM Administration .
6 - 22 Trusted Platform Module
4. The TPM Management window allows you to configure the TPM within Windows .
As TPM is usually administered within large enterprises and organizations, your system administrator will need to assist you in managing the information here.
Modules
Figure 6 - 17
Trusted Platform
Module (TPM)
Management on
Local Computer
Administration
6
Trusted Platform Module 6 - 23
Modules
6
Figure 6 - 18
TPM Actions Menu
TPM Actions
1. Click Prepare the TPM and follow the instructions in the Wizard to prepare the
TPM (this will probably require a restart of the computer and confirmation of the setting changes after restart by pressing the appropriate F key).
2. After the restart the TPM will be prepared and you can then use the Actions menu to Turn TPM off , Change Owner Password , Clear TPM or Reset TPM Lockout .
3. A wizard will help take you through any setup steps.
6 - 24 Trusted Platform Module
BitLocker
BitLocker Drive Encryption can be used in conjunction with the TPM to encrypt data on the disk. Access the Microsoft BitLocker Drive Encryption control panel applet from the Windows control panel ( System and Security ).
1. Click Turn on Bit Locker .
2. Follow the on-screen instructions to setup BitLocker, and make sure you have a removable media (e.g. a USB flash drive) to store saved recovery keys etc.
Modules
Figure 6 - 19
BitLocker Drive
Encryption
6
Trusted Platform Module 6 - 25
Modules
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Make sure the WLAN,
6
Bluetooth and 3G/4G module(s) are OFF (or the system is in Air- plane Mode ) if you are using the computer aboard aircraft (see
3G/4G Module
If you have included an optional UMTS/HSPA+ based 3G Module (Universal Mo- bile Telecommunications System or High Speed Packet Access) module or LTE
(Long Term Evolution) 4G module (see “Communication” on page D - 3 for spec-
ification details) in your purchase option, you do not require a driver/application installation for Windows 10 . Follow the instructions overleaf to install the USIM card (which will be provided by your service provider), and then use the Charms
Bar Wireless icon to access the 3G/4G network in the same manner as the WLAN.
Important Notice
If your purchase option includes both Wireless LAN and 3G/4G modules, then the appro- priate antennas will be installed. Note that In order to comply with FCC RF exposure com- pliance requirements, the antenna must not be co-located or operate in conjunction with any other antenna or transmitter.
Important Notice - 3G/4G & Bluetooth/Wireless LAN Modules
In order to comply with FCC regulations you should NOT operate the 3G/4G module and the Bluetooth/Wireless LAN modules at the same time as this may disrupt radio frequency, and cause interference. When the 3G/4G module is powered on, make sure that the Blue- tooth/Wireless LAN modules are powered off.
6 - 26 3G/4G Module
3G/4G Module USIM Card Installation
Remove the battery (see “Removing the Battery” on page 1 - 18 ) and insert the
USIM card 1 as illustrated below (pay careful attention to the orientation of the card as the gold contact side of the card should face downwards) until it clicks fully into position. To eject the card simply press it until it ejects, but do not attempt to eject the card while connected to a 3G/4G network (see below).
1
USIM Card Ejection
Simply press on the USIM card to eject it, however do not do this while a connection is in progress. If you do eject the card while a 3G/4G connection is ongoing, you will need to shut down the system, re- insert the USIM card, restart the system and then reestablish the 3G/4G connection.
If you wish to change USIM cards then you will need to shut the system down, reinsert the USIM card, restart the system and then reestablish the 3G/4G connection.
Modules
USIM Card
Orientation
Note that the USIM card’s readable side
(with the gold-colored contacts) should face downwards as illustrated.
6
Figure 6 - 20
USIM Card Insertion
3G/4G Module 6 - 27
6
Modules
Figure 6 - 21
Wi-Fi Menu with
Wi-Fi On & Off
Figure 6 - 22
Cellular Menu
(Disconnected)
3G/4G Configuration
You can configure a 3G/4G connection as below, however make sure the system is not in Airplane Mode before configuration begins and turn Wi-Fi Off in order to use your 3G/4G connection as priority . You can connect to a 3G/4G connection in much the same way as the WLAN connection except you use the Cellular menu.
1. Click the Wireless icon in the notification area of the taskbar and click on the Wi-Fi icon in order to turn it off (the Wi-Fi icon will be grayed out when off).
2. Make sure that Airplane mode is off (the Airplane mode icon should be gray).
3. Click the Cellular button to turn it On .
6 - 28 3G/4G Module
4. Click Connect to connect to the cellular network manually.
5. Once connected you can then access the internet, download e-mail etc. as per any internet connection.
6. Click Disconnect to drop the connection to the cellular network.
7. You will need to turn your Wi-Fi on again after disconnecting.
Modules
Power Saving States &
Cellular Connections
Note that if your system goes in to a power sav- ing state, you will need to reconnect to your cel- lular network when the system resumes.
Figure 6 - 23
Cellular Connection
6
3G/4G Module 6 - 29
6
Modules
Figure 6 - 24
Network & Internet
Settings > Cellular
8. Cellular in Network & Internet in Windows Settings will allow you to access some further cellular settings.
6 - 30 3G/4G Module
9. Click Advanced options to access more detailed menu options.
Modules
Figure 6 - 25
Cellular > Advanced
Options
6
3G/4G Module 6 - 31
6
Modules
6 - 32
Troubleshooting
Chapter 7: Troubleshooting
Overview
Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
If all else fails, talk to your service representative. You should also make a record of what happened and what remedies you tried.
Of course, if something goes wrong, it will happen at the most inconvenient time possible, so you should preview this section just in case. If, after you’ve tried everything, and the system still won’t cooperate, try turning it off for a few minutes and then rebooting. You will lose any unsaved data, but it may start working again. Then call your service representative.
7
Overview 7 - 1
7
Troubleshooting
Basic Hints and Tips
Many of the following may seem obvious but they are often the solution to a problem when your computer ap- pears not to be working.
•
Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip , make sure it is actually working. Check the LED Power Indicators
“LED Indicators” on page 1 - 7
to see the computer’s power status.
• Connections - Check all the cables to make sure that there are no loose connections anywhere.
• Power Savings - Make sure that the system is not in Hibernate or Sleep mode by pressing the keys config- ured in your P ower Options
“Configuring the Power Buttons” on page 3 - 9
Fn + F12 key com- bination, or power button to wake-up the system.
• Brightness - Check the brightness of the screen by pressing the Fn + F8 and F9 keys to adjust the bright-
ness (see Table , on page 1 - 12 ).
•
Display Choice - Press Fn + F7 to make sure the system is not set to “external only” display.
• Boot Drive - Make sure there are no optical media and/or USB storage devices in any connected drive.
7 - 2 Basic Hints and Tips
Troubleshooting
Backup and General Maintenance
• Always backup your important data, and keep copies of your OS and programs safe, but close to hand.
Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wal- let.
• Run maintenance programs on your hard disk and OS as often as you can. You may schedule these pro- grams to run at times when you are not using your computer. You can use those that are provided free with your OS, or buy the more powerful dedicated programs to do so.
• Write down your passwords and keep them safe (away from your computer). This is especially important if you choose to use a Boot
password for the SCU (see “Security Menu” on page 5 - 11 ).
•
Keep copies of vital settings files such as network, dialup settings, mail settings etc. (even if just brief notes).
Bottom Cover Removal Warning
Users should not remove any cover(s) and /or screw(s) for the purposes of device upgrade as this may violate the terms of your warranty. If you need to replace/remove the hard disk/RAM/optical device etc., for any reason, please contact your dis- tributor/supplier for further information.
7
Backup and General Maintenance 7 - 3
7
Troubleshooting
Viruses
• Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the defini- tions file updates are usually downloadable directly from the internet.
•
Be careful when opening e-mail from sources you don’t know. Viruses are often triggered from within e- mail attachments so take care when opening any attached file. You can configure most Anti-Virus pro- grams to check all e-mail attachments . Note : You should also beware of files from people you know as the virus may have infected an address book and been automatically forwarded without the person’s knowl- edge.
• Keep a “ Bootable CD-ROM/DVD-ROM/USB storage device ” (this CD/DVD/USB device provides basic information which allows you to startup your computer) handy. You may refer to your OS’s documentation for instructions on how to make one, and many Anti-Virus programs will also provide such a disk (or at least instructions on how to make one).
7 - 4 Viruses
Troubleshooting
Upgrading and Adding New Hardware/Software
•
Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system.
• Don’t open your computer or undertake any repair or upgrade work if as this may violate the terms of your warranty.
•
Read the documentation . We can assume, since you are reading this that you are looking at the computer’s manual, but what about any new peripheral devices you have just purchased? Many problems are caused by the installation of new hardware and/or software. Always refer to the documentation of any new hardware and/or software, and pay particular attention to files entitled “ READ ME
” or “
READ ME FIRST
”.
•
When installing a new device always make sure the device is powered on, and in many cases you will need to restart the computer. Always check that all the cables are correctly connected.
• Make sure you have installed the drivers for any new hardware you have installed (latest driver files are usually available to download from vendor’s websites).
•
Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs.
7
Upgrading and Adding New Hardware/Software 7 -
37
7
Troubleshooting
•
Don’t over complicate things. The less you have to deal with then the easier the source of the problem may be found; Example - if your computer has many devices plugged into its ports, and a number of programs running, then it will be difficult to determine the cause of a problem. Try disconnecting all of the devices and restarting the computer with all the peripheral devices unplugged. A process of elimination (adding and removing devices and restarting where necessary) will often find the source of a problem, although this may be time consuming.
7 - 6 Upgrading and Adding New Hardware/Software
Troubleshooting
Problems and Possible Solutions
Problem
You turned on the power but it doe sn’t work.
The battery LED power indicator blinking orange.
, is
Possible Cause - Solution
Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there
’s nothing interfering with the battery contacts.
Low Battery. Plug in the DC power source. If the computer do esn’t start up immediately, turn it off then on again.
You are losing battery power too quickly. The system is using too much power. If your OS has a Power Options scheme
(see “Power Plans” on page 3 - 5 ) check its settings. You may also be using a
peripheral device/USB device that is drawing a lot of power.
Actual battery operating time is shorter than expected.
The battery has not been fully discharged before being recharged. Make sure the battery is fully discharged and recharge it completely before reusing (see
“Battery Information” on page 3 - 17 ).
Power Options have been disabled. Go to the Control Panel in Windows and re-enable the options.
A peripheral device/USB device is consuming a lot of power. Turn off/remove the unused device to save power.
7
Problems and Possible Solutions 7 - 39
7
Troubleshooting
Problem Possible Cause - Solution
The computer feels too hot . Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn
’t cool it down, put the system into
Hibernate mode or turn it off for an hour. Make sure the computer i sn’t sitting on a thermal surface (see
’re using the correct adapter.
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a notebook which is powered on in a travel bag may cause the Vent/Fan intakes to be blocked.
The system will not wake up from a power saving state (Sleep/Hibernate) on network activity (Wake on LAN) even though I have plugged in the powered
AC/DC adapter .
Wake on LAN is supported in AC mode only .
When the system enters a power saving state the plugged in AC/DC adapter should be connected, and should remain connected, in order to allow the system to wake up on network activity. Unplugging the adapter, and then plugging it back in again, will not allow the system to wake up on network activity.
No image appears on the external monitor I have plugged in and powered on.
You haven ’t installed the video driver and configured it appropriately from the
Control Panel .
See Appendix C for instructions on installing and configuring
the video driver.
7 - 8 Problems and Possible Solutions
Problem
Nothing appears on screen.
Possible Cause - Solution
Troubleshooting
The system is in a power saving mode . Toggle the sleep/resume key combination, Fn + F12
(see “Configuring the Power Buttons” on page 3 - 9 ).
The screen controls need to be adjusted. Toggle the screen control key combinations Fn + F8/F9
. If you’re connected to an external monitor, make sure it
’s plugged in and turned on. You should also check the monitor’s own brightness and contrast controls.
The computer is set for a different display. Toggle the screen display key combination, Fn + F7 . If an external monitor is connected, turn it on.
The screen saver is activated. Press any key or touch the TouchPad .
You forget the boot password . If you forget the password, you may have to discharge the battery of the CMOS.
Contact your service representative for help.
Password Warning
If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
7
Problems and Possible Solutions 7 - 9
7
Troubleshooting
Problem Possible Cause - Solution
The sound cannot be heard or the volume is very low .
The volume might be set too low. Check the volume control in the Volume
Control Panel in the Windows notification area, or use the key combination Fn
+ F5 and F6
(see “Function Keys & Visual Indicators” on page 1 - 12 ) to
adjust.
Unwelcome numbers appear when typing. Num Lock is turned ON
(see “LED Indicators” on page 1 - 7 ).
Other Keyboards
If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work.
The system freezes or the screen goes dark.
The system ’s power saving features have timed-out . Use the AC/DC adapter, press the sleep ( Fn + F12 ) key combination, or press the power button if no
LEDs are lit.
The system never goes into a power saving mode .
Power Options features are not enabled. Go to the Windows Power Options menu and enable the features you prefer (see
“Power-Saving States” on page 3 - 7 ). Make sure you have enabled
Hibernate mode from the control panel.
7 - 10 Problems and Possible Solutions
Troubleshooting
Problem
The Wireless LAN/Bluetooth modules cannot be detected.
The PC Camera module cannot be detected.
The Wireless LAN/Bluetooth modules cannot be configured.
Possible Cause - Solution
The modules are off as the computer is in Airplane Mode . Check the LED indicator to see if it is in Airplane Mode
(see “LED Indicators” on page 1 -
Fn + F11 key combination to toggle Airplane Mode on/off (see
Table 1 - 3, on page 1 - 12 ).
The module is off. Press the Fn + F10 key combination in order to enable the
module (see “Function Keys & Visual Indicators” on page 1 - 12 ). Run the
camera application to view the camera picture.
The driver(s) for the module(s) have not been installed. Make sure you have installed the driver for the appropriate module (see the instructions for the
appropriate module in “Wireless LAN Module” on page 6 - 2 and/or
“Bluetooth & WLAN Combo Module” on page 6 - 7
A file cannot be copied to/from a connected Bluetooth device.
The transfer of data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not supported) . If you are copying a file from your computer to a Bluetooth enabled device, you will not be able to copy a file from the Bluetooth enabled device to your computer until the file transfer process has been completed
7
Problems and Possible Solutions 7 -
11
7
Troubleshooting
Problem Possible Cause - Solution
A file being copied to/from a connected
Bluetooth device appears to be transferring very slowly .
You may have the Bluetooth control panel (Settings > Devices > Bluetooth) open . When transferring data between the computer and a Bluetooth enabled device, make sure that the Bluetooth control panel is closed .
Bluetooth Control Panel
(Settings > Devices)
Close the Bluetooth control pan- el (pictured on the right) when transferring data between the com- puter and a Bluetooth enabled de- vice.
My internal microphone seems to be disabled and/or I can still hear sound from the speakers even though I have plugged headphones into the headphone jack.
You have disabled
“Front panel jack detection” in Connector Settings in the
Realtek HD Audio Manager control panel. Go to the Realtek HD Audio
Manager and click the Connector Settings icon and make sure that there is no tick along side “Front panel jack detection” and click OK.
No sound can be heard through an HDMI connected display.
You have not configured the HDMI audio output
Configuratio n” on page C - 20
7 - 12 Problems and Possible Solutions
Troubleshooting
Problem
When using a Bluetooth headset the audio appears to be mono and not stereo.
Possible Cause - Solution
This is a common issue with Bluetooth headsets. To resolve this issue do the following (you will need to repeat this procedure after every boot up , restart , or when the system resumes from hibernation ):
1. Go to the Devices & Printers control panel in Windows .
2. Double-click the Bluetooth headset.
3. Click Connect to complete the stereo connection.
OR
1. Go to the Sound control panel in Windows .
2. Right-click (in the Playback tab) the Bluetooth Stereo Audio device (the default device is Headset ).
3. Click Connect to complete the stereo connection.
7
Problems and Possible Solutions 7 -
13
7
Troubleshooting
Problem Possible Cause - Solution
I have used Update Driver in Device
Manager (Unknown device > Other
Devices) to try and install the Airplane
It is very important that the drivers are installed in the order indicated in Chapter
4 (which is the numbered installation order on the Device Drivers & Utilities +
User ’s Manual disc). This issue can occur when drivers are manually installed, and not in the correct order.
Mode driver. Windows encountered a problem in attempting to update the driver, and a yellow exclamation mark appears in Device Manager against the Unknown device.
If you have attempted to Update Driver from the Device Manager control panel and have encountered problems, then use the method below to correct this:
To correct this problem:
4. Go to the Programs and Features ( Programs ) control panel in
Windows .
5. Select any installed Airplane Mode driver item (e.g. Insyde Airplane
Mode HID Mini-Driver), and click Uninstall/Change to uninstall the current driver.
6. Restart the computer.
7. Insert the Device Drivers & Utilities + User ’s Manual disc and click
Install Drivers (button).
8. Double-click the Airplane Driver item in the menu.
9. Follow the instructions to install the correct driver (you will need to restart the computer as part of the installation process).
7 - 14 Problems and Possible Solutions
Troubleshooting
Resolving the
“Can’t connect to this network” issue with the 3G/4G Module
1. If you have issues connecting to the cellular network when you are attempting to use the 3G/4G network then you may need to manually connect to the Internet access point name (APN) .
2. Usually the Internet APN is set automatically, however if your cellular data connection isn't working, you should try manually entering a new Internet APN based on your location and mobile operator.
3. To find your APN settings contact your mobile operator directly (or of you can connect to a WiFi network on your
PC, or have a phone handy, try searching online to find the Internet APN settings for your mobile operator).
4. See http://windows.microsoft.com/en-us/windows-10/cellular-settings or search the Microsoft website for
" Windows 10 cellular settings ".
7
Problems and Possible Solutions 7 -
15
7
Troubleshooting
7 - 16
Interface (Ports & Jacks)
Appendix A: Interface (Ports & Jacks)
Overview
The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
A
Interface (Ports & Jacks) A -
17
A
Interface (Ports & Jacks)
Notebook Ports and Jacks
Item
Card Reader Port
DC-In Jack
External Monitor (VGA) Port
Description
The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device.
•
MMC (MultiMedia Card) / RSMMC
•
SD (Secure Digital) / Mini SD / SDHC / SDXC
Plug the supplied AC/DC adapter into this jack to power your computer.
This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or simultaneous display on the LCD and external monitor/FPD.
HDMI-Out Port
Headphone-Out Jack
The HDMI-Out ( High-Definition Multimedia Interface ) is an audio/video connector interface for transmitting un compressed digital streams. This allows you to connect an external monitor, TV or Flat Panel Display etc. as a display device by means of a HDMI cable. Note that HDMI carries both audio and video signals .
Headphones or speakers may be connected through this jack. Note : Set your system
’s volume to a reduced level before connecting to this jack.
Microphone-In Jack Plug an external microphone in to this jack to record on your computer.
A - 2 Interface (Ports & Jacks)
Item Description
Interface (Ports & Jacks)
RJ-45 LAN Jack This port supports LAN (Network) functions.
Note : Broadband (e.g. ADSL) modems usually connect to the LAN port.
Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store.
USB 2.0/1.1 Port
USB 3.0 Ports
(USB 3.1 Gen 1 - Type A or C)
USB 3.1 Ports
(USB 3.1 Gen 2 - Type A or C)
These USB 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc. Devices can be plugged into the computer, and unplugged from the computer, without the need to turn the system off (if the power rating of your USB device is 500mA or above, make sure you use the power supply which comes with the device).
USB 3.0 will transfer data much faster than USB 2.0, and is backwards-compatible with
USB 2.0.
Note: The maximum amount of current supplied by USB Type-C ports is 500 mA for USB2.0/900 mA for USB 3.1
The USB 3.0 ports capable of 5Gbps (SuperSpeed) are classified as USB 3.1 Gen 1.
There are two Type A USB 3.1 Gen 1 ports and one Type C USB 3.1 Gen 1 port on this computer model. Type A is the larger blue colored port and Type C is the smaller sized
black colored port. See “Right & Left Views” on page 1 - 14 .
Note: 2 * USB 3.1 (Gen 2 Type A or C) ports (are available as a factory option for this computer model series. USB 3.1 (Gen 2) ports are capable of 10Gbps SuperSpeed+ for a single device, or if two devices are plugged in to both USB 3.1 (Gen 2) ports, this bandwidth will be shared between the ports. The USB 3.1 ports are shared with the
USB 3.0 ports in this option. See
“Right & Left Views” on page 1 - 14
Interface (Ports & Jacks) A -
19
A
A
Interface (Ports & Jacks)
A - 4
Appendix B: Control Center
Overview
The following chapter will give a quick description of the functions of the Control Center . The Control Center gives quick access to frequently used controls, power management features and enables you to quickly turn mod- ules on/off. Click the Control Center icons to toggle the appropriate function, or hold the mouse button down and move the dial control where applicable. Certain functions will automatically be adjusted when a power mode is selected. The Control Center in Windows 10 works under the Desktop App and not under the Start screen.
Control Center Access
To run the Control Center press the Fn + Esc key com- bination, or double-click the icon in the notification area of the taskbar.
B
Close the Control Center by clicking the close icon in the top right of the panel
(move the cursor onto the top right corner of the panel to highlight it).
Figure B - 1 - Control Center
Overview B -
21
B
Power Modes
You can set a Power Mode by clicking the appropriate icon at the top of the Control Center . Each power mode will affect the Power Conservation Mode, Airplane Mode, Power Plan and PC camera power etc.
You can click a Control Center icon to set an overall power mode and then click individual icons in the
Control Center to power on/off the Touchpad and PC camera.
Modes Quiet Power Saving Performance Entertainment
Icon
Power Plan Balanced Power Saver High Performance Balanced
Balance Power Saving Performance Balance Power Conservation Mode
PC Camera
TouchPad
Airplane Mode
ON
ON
OFF
OFF
ON
ON
Table B - 1 - Power Modes
ON
ON
OFF
ON
ON
OFF
B - 2 Overview
Control Center Menus
The Control Center contains 2 menu headings ( System Program and Device ) under the Power Modes.
Click the menu headings and then click any of the buttons outlined on the following pages.
Figure B - 2 - Control Center Menus
B
Overview B - 3
Power Status (System Program)
The Power Status icon will show whether you are currently powered by the battery, or by the AC/DC adapter plugged in to a working power outlet. The power status bar will show the current battery charge state.
B
CPU Temperature (System Program)
The temperature icon will display the current CPU temperature. Click the icon to have the temperature dis- played in either degrees Celsius or Fahrenheit.
Brightness (System Program)
The Brightness icon will show the current screen brightness level. You can use the slider to adjust the screen brightness or the Fn + F8/F9 key combinations, or use the Fn+ F2 key combination to turn off the LED backlight
(press any key to turn it on again).
Volume (System Program)
The Volume icon will show the current volume level. You can use the slider to adjust the Volume or the Fn +
F5/F6 key combinations, or use the Fn+ F3 key combination to mute the volume.
Fan Speed (System Program)
You can set the fan speed to Maximum (full power) , Automatic or Custom from this menu item. The fan speed will adjust itself automatically to control the heat of the CPU. However you can adjust the setting to maximum if you prefer. Select Custom and click on the sliders to adjust the settings to your preference, however these set- tings can be overridden by the system, as a safety precaution, if it requires heavier use of the fan (see over).
B - 4 Overview
Custom Settings
Click Save to retain customized settings, or Reset to select default settings.
Power Conservation (System Program)
This system supports Energy Star power management features that place computers (CPU, hard drive, etc.) into a low-power sleep modes after a desig- nated period of inactivity (see
“Power Conservation Modes” on page 3 - 12
). Click either the Performance ,
Balanced or Power Saving button.
Sleep Button (System Program)
Click either the Hibernate or Sleep buttons to have the computer enter the selected power-saving mode when the Fn + F4 key combination is pressed (see
“Power-Saving States” on page 3 - 7
).
B
Display Switch (System Program)
Click the Display Switch button to access the menu (or use the + P key combination) and select the appro- priate attached display mode.
Time Zone (System Program)
Clicking the Time Zone button will access the Date and Time Windows control panel.
Overview B - 5
B
Desktop Background (System Program)
Clicking the Desktop Background button will allow you to change the desktop background picture.
Backlight Keyboard (Device)
Click the numbers under the Backlight Keyboard icon to adjust the brightness of the keyboard backlight LED.
TouchPad/PC Camera (Device)
Click either of these buttons to toggle the TouchPad or camera module’s power status. The icon will appear dimmed when it is off
.
Note that the power status of the camera module is also effected by the Power Mode selected (see Table B - 1, on page B - 2 ).
Caps Lock/Scroll Lock/ Number Lock/Airplane Mode
Click the button to toggle the appropriate lock mode and Airplane Mode.
B - 6 Overview
Appendix C: Video Driver Controls
The basic settings for configuring the LCD are outlined in
Video Driver Installation
Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 4 .
1.
Insert the Device Drivers & Utilities + User’s Manual disc and click
Install
Drivers
(button).
2.
Click 2.Install VGA Driver > Yes .
3.
Click Next > Yes > Next > Next .
4.
Click Finish to restart the computer.
Note : After installing the video driver go to the Display / Display Settings control panel to adjust the video settings to the highest resolution.
Dynamic Video Memory Technology
Intel
®
DVMT automatically and dynamically allocates as much system memory
(RAM) as needed to the integrated video system ( the video driver must be installed ). DVMT returns whatever memory is no longer needed to the operating sys- tem.
Video Driver Controls
Video Card Options
Note that card types, specifications and driv- ers are subject to contin- ual updates and changes. Check with your distributor/supplier for the latest details on video cards supported.
DVMT Notes
DVMT is not local video memory.
DVMT will not function in MS-DOS. DOS uses the legacy memory indi- cated.
C
Video Driver Installation C - 1
C
Video Driver Controls
Intel ® HD Graphics Control Panel
Advanced video configuration options are provided by the Intel ® HD Control Pan- el . To access the control panel see below and overleaf:
1. Right-click the Desktop and select Intel(R) Graphics Settings from the menu.
Figure C - 1
Right-Click Desktop
(Intel Graphics
Settings)
Figure C - 2
Taskbar Notification
Area Icon Menu
OR
2. Click the icon in the notification area of the Desktop taskbar and select Intel(R)
Graphics Settings from the menu.
C - 2
Intel® HD Graphics Control Panel
OR
3. Double-click the Intel(R) HD Graphics control panel in the Windows Control
Panel .
Video Driver Controls
Figure C - 3
Control Panel
Intel ® Graphics
Settings
C
Int el® HD Graphics Control Panel C - 3
Video Driver Controls
You may make changes to any of the graphics properties by clicking the appropriate menu panel and adjusting the settings from the menus.
Home
Click the Home button to return to the main menu screen in any of the sub- menu screens.
C
Figure C - 4
Intel® HD Graphics
Control Panel
C - 4 I ntel® HD Graphics Control Panel
Display
Click either Display Settings or Color Settings to make display adjustments, in- cluding configuration for any attached external displays.
Video Driver Controls
Multiple Display
At least one other dis- play must be attached in order to view multiple display selection op- tions.
Figure C - 5
Intel® HD Graphics
Control Panel
Display
C
Int el® HD Graphics Control Panel C - 5
C
Video Driver Controls
Multiple Display
Click the Display menu at the top of the screen to display the sub-menus. The Mul- tiple Displays menu allows you to configure the display mode of any attached dis-
plays (see “Attaching Other Displays” on page C - 16 ). Click
Apply to save any changes made.
At least one other dis- play must be attached in order to view multiple display selection op- tions.
Audio Settings
Any attached active dis- plays must have audio capacity to allow audio configuration.
Figure C - 6
Intel® HD Graphics
Control Panel
Display - Multiple
Displays
C - 6 I ntel® HD Graphics Control Panel
The Custom Resolutions sub-menu allows you to adjust the display (or any at- tached display) to any width, height, refresh rate, color depth and underscan percent- age of your choice. Note that incorrect settings can cause system instability and even possible component damage, so this is adjusted at your own risk.
Video Driver Controls
Figure C - 7
Intel® HD Graphics
Control Panel
Display Settings -
Custom
Resolutions
C
Int el® HD Graphics Control Panel C - 7
Video Driver Controls
3D
This menu allows you to choose how 3D images are displayed. Performance gives the smoothest motion of images , Quality displays the most detail, Balanced Mode provides better computer performance with good quality and Custom allows you to configure the Anisotropic Filtering and Vertical Sync and features to your prefer- ences. Click Apply to save changes.
C
Figure C - 8
Intel® HD Graphics
Control Panel 3D
C - 8 I ntel® HD Graphics Control Panel
Options and Support
Hot Key Manager in Options and Support allows you to create hot keys for open- ing the application, rotating the display, scaling etc. Click Apply to save changes.
Video Driver Controls
Figure C - 9
Intel® HD Graphics
Control Panel
Options and
Support
C
Int el® HD Graphics Control Panel C - 9
Video Driver Controls
Preferences
Click the Options menu at the top of the screen to display the sub-menus. The In- formation Center provides details on System Information , the Built-In Display and any attached displays .
Go to the Preferences sub-menu in Options to configure the preferences for the In tel® HD Graphics
Control Panel.
Make sure you click En- able under Tray Icon to display the Intel® HD
Graphics Control Panel icon in the notification area of the taskbar (as below).
C
Figure C - 10
Intel® HD Graphics
Control Panel
Options -
Information Center
C - 10 I ntel® HD Graphics Control
Panel
Video
The Video menu allows you to brighten or darken movies, or to switch to vivid col- ors. The Preview image will display a sample image using the current settings. You can Save Profile and name the Profile to recall the settings at any time. Click Apply to save changes (select Color Enhancement , Image Enhancement , Image Scaling or Gamut Mapping from the menu).
Video Driver Controls
Figure C - 11
Intel® HD Graphics
Control Panel -
Video
(Color
Enhancement)
C
Int el® HD Graphics Control Panel C - 11
C
Video Driver Controls
Click the Video menu at the top of the screen to display the sub-menus.The Image
Enhancement menu allows you to adjust the Sharpness , Skin Tone Enhancement in the Basic menu, and Noise Reduction, Contrast Enhancement and Film Mode
Detection in the Advanced menu. Click Apply to save changes.
Figure C - 12
Intel® HD Graphics
Control Panel - Video
(Image
Enhancement Basic)
C - 12
Intel® HD Graphics Control Panel
Enable Image Scaling to use the sliders to adjust the scaling.
Video Driver Controls
Figure C - 13
Intel® HD Graphics
Control Panel Video
Image Scaling
C
Int el® HD Graphics Control Panel C - 13
Video Driver Controls
Profiles
You can select one of the preset profiles ( Brighten Video , Darken Video and En- hance Video Colors ) from the menu on the left. Alternatively you can go through the menus to make adjustments to your preferences for Display , Color , Video , 3D ,
Options and Support and Power (tick any boxes for the settings required), and then
Save the settings to a profile (which may be imported or exported).
C
Figure C - 14
Intel® HD Graphics
Control Panel -
Profiles
C - 14
Intel® HD Graphics Control Panel
Display Devices & Options
Note that you can use external displays connected to the HDMI-Out port and/or ex- ternal monitor port. See your display device manual to see which formats are sup- ported.
Attaching Displays
Video Driver Controls
4K2K Videos on 4K2K
External Displays
Note you may experi- ence some video lag when playing 4K2K vid- eos on an attached
4K2K external display.
When you first attach an external display you may find that the desktop does not occupy the full screen area. Use either the disp lay’s auto adjust/configure controls, or the Intel(R)
HD Graphics Control Panel to configure the full screen display.
Table C - 1
Display Modes
Display Mode
Single Display
Description
One of the connected displays is used as the display device ( PC screen only or Second screen only ).
Clone/Duplicate
Both connected displays output the same view and may be configured independently
Extended / Extend
Both connected displays are treated as separate devices, and act as a virtual desktop
C
Display Devices & Options C - 15
Video Driver Controls
Attaching Other Displays
Multiple Display
At least one other dis- play must be attached in order to view Multiple
Display selection op- tions.
To Clone Displays:
1. Attach your external display to the HDMI-Out port/external monitor port, and turn it on.
2. Go to the Intel(R) HD Graphics Control Panel control panel and click Display >
Multiple Displays (sub-menu).
3. Click Clone from the Select Display Mode menu.
4. Click Apply , and OK to confirm the settings change.
5. Select the displays from the Select One or More Active Displays menu.
C
Figure C - 15
Display > Multiple
Displays (Clone)
C - 16 Attaching Other Displays
To Enable Extended Mode:
1. Attach your external display to the HDMI-Out port/external monitor port, and turn it on.
2. Go to the Intel(R) HD Graphics Control Panel control panel and click Display >
Multiple Displays (sub-menu).
3. Click Extended from the Select Display Mode menu.
4. Click Apply , and OK to confirm the settings change.
Video Driver Controls
Display Settings
Extended Desktop
You can have different
Colors, Screen Area and Monitor Refresh
Rates for each display device provided your monitor can support them .
You can drag the moni- tor icons to match the physical layout of your displays. Icons and pro- grams may also be dragged between the displays.
Figure C - 16
Display > Multiple
Click the appropriate monitor icon and drag it to match the physical arrange- ment you wish to use (e.g. the secondary display may be extended left/right/ above/below the primary display).
Displays (Extended)
C
Attaching Other Displays C - 17
C
Video Driver Controls
Configure Other Displays Using Project
You can configure attached displays from Project .
1. Attach your display to the appropriate port, and turn it on.
2. Press the + P key combination.
3. Click on any one of the options from the menu to select PC screen only ,
Duplicate , Extend or Second screen only .
4. You can also click Connect to a wireless display at the bottom of the Project screen and follow the steps to connect to any wireless enabled display.
Figure C - 17
Project
C - 18 Configure Other Displays Using Project
Configuring an External Display In Windows
The System Control Panel in Settings may also be used to configure displays.
1. Attach your external display to the appropriate port, and turn it on.
2. Click the Start Menu and click Settings > System (or right-click the desktop and select Display Settings ).
3. You can change Duplicate, Extend or choose to display on 1 screen only.
4. Click Apply to save any changes made.
5. Click Advanced display settings to access further options.
Video Driver Controls
Figure C - 18
System > Display
C
You can configure attached displays from Project. C - 19
Video Driver Controls
HDMI Audio Configuration
Volume Adjustment
HDMI (High-Definition Multimedia Interface) carries both audio and video signals.
In some cases it will be necessary to go to the Sound control panel and manually configure the HDMI audio output as per the instructions below.
The sound volume level can be clicking using the volume control icon in the notification area of the taskbar .
1. Go to the Sound control panel.
2. Click Playback (tab)
3. The playback device will be selected.
4. You may need to select the audio device and click Set Default (button).
5. Double-click the device to access the control panel tabs.
C
Figure C - 19
Sound - HDMI
Device (set Default)
C - 20 HDMI Audio Configuration
6. Adjust the HDMI settings from the control panel tabs.
7. Click OK to close the Sound control panel.
Video Driver Controls
Figure C - 20
HDMI Device
Properties
C
HDMI Audio Configuration C - 21
C
Video Driver Controls
Other Applications
If you are using a third party application to play
DVDs etc. from any at- tached DVD device, you will need to consult the applicatio n’s docu- mentation to see the appropriate audio con- figuration (the applica- tion must support digital to analog translation).
HDMI Notes
•
Connect a device with HDMI support to the HDMI-Out port BEFORE attempt- ing to play audio/video sources through the device.
• To play audio sources through your external display’s (TV or LCD) speakers you will need to go to the audio configuration control panel on the display and configure the audio input accordingly (see your display device manual).
HDMI Video Configuration
1. Connect an HDMI cable from the HDMI-Out port to your external display.
2. Configure your external display as per the instructions in “Attaching Other
3. Set up your external display (TV or LCD) for HDMI input (see your display device manual).
4. You can now play video/audio sources through your external display.
C - 22 HDMI Audio Configuration
Wireless Display
Wireless Display uses your Wireless LAN module/WLAN Bluetooth Combo mod- ule (you need to make sure that your video adapter/display device is compatible with your particular WLAN/Combo module) in conjunction with a compatible video adapter/display device (purchased separately) to allow you to display the contents of the notebook display on another display (e.g. HDTV), without the need to have cables stretching across a room.
You can use the wireless display to play games, browse the internet, display videos or photo slide shows on your TV/external display without using HDMI or A/V ca- bles.
Before configuring Wireless Display you will need to set up your compatible adapter with your display/speakers. Connect the adapter using an HDMI or A/V ca- ble and turn on the display (or in the case of speakers connect them to the wireless speaker adapter with the cables provided with the adapter), and then set the display to the appropriate input channel (see the documentation supplied with your compat- ible adapter/display for full details).
Note that no driver or application is required for wireless display in Windows 10 .
Video Driver Controls
Compatible
Adapters
For a list of compatible adapters check the vid- eo adapter/display de- vice documentation, or with your distributor/ supplier.
C
HDMI Audio Configuration C - 23
Video Driver Controls
Wireless Display Configuration
1. Note that no driver or application is required for wireless display in Windows 10 .
2. Press the + P key combination.
3. Click Connect to a wireless display at the bottom of the Project screen and follow the steps to connect to any wireless enabled display.
Figure C - 21
Add a Wireless
Display
C
4. The system will then search for compatible display devices ( this may take up to
60 seconds so allow time for this to complete).
5. Double-click any detected display device in the list.
C - 24 Wireless Display Configuration
6. You may then need to input a pin number for the device to which you are connecting and click Next .
7. The display will then connect (for specific settings for your display see the documentation supplied with your compatible adapter/display for full details).
8. Go to the Project menu and click Disconnect to temporarily disconnect from the wireless display.
9. To permanently disconnect from the display (you will need to go back through the connection process again) you can select it in Devices and click Remove Device
> Yes .
Video Driver Controls
C
Wireless Display Configuration C - 25
C
Video Driver Controls
C - 26
Specifications
Appendix D: Specifications
Latest Specification Information
The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your distributor/supplier for details.
Note that this computer model series may support a range of CPUs and/or video adapters.
To find out which CPU is installed on your system go to the Start menu and select Settings , and then select System and click About . This will also provide information on the amount of Installed RAM etc.
To get information on your system’s video adapter go to the Start menu and select Settings , and then select System and click Display> Advanced display settings > Display adapter properties.
D
Specifications D -
27
D
Specifications
Core Logic
Mobile Intel ® H170 Express Chipset
Display
15.6" (39.62cm) FHD (1920 * 1080) / HD
(1366 * 768), 3.8 mm, 16:9 Backlit Panel
Memory
Dual Channel DDR4
Two 260 Pin SO-DIMM Sockets
Supporting DDR4 2133 MHz Memory
Modules ( real operational frequency depends on the FSB of the processor )
Memory Expandable up to 32GB
(maximum), Compatible with 4GB/8GB/
16GB Modules
Storage
One Changeable 2.5" 7mm(h) Hard Disk
Drives (HDD) / Solid State Drives (SSD) with SATA Interface
One M.2 2280 SSD with SATA Interface
( Factory Option )
OR
One M.2 2280 SSD with PCIe Gen x3/x4
Interface ( Factory Option )
One Changeable Super Multi 9.5 mm (h)
Optical Device Drive (ODD) with SATA
Interface
One Changeable Caddy Bay for 9.5 mm
(h) Optical Device Drive (ODD), 2.5"
7 mm (h) HDD / SSD with SATA Interface
( Factory Option )
Audio
High Definition Audio
S/PDIF Digital Output
Built-In Microphone
Built-In Array Microphone ( Factory
Option )
2 Built-In 2W Speakers
Keyboard & Pointing Device
Full Size Keyboard with Numeric Pad
Full Size White LED Illuminated
Keyboard with Numeric Pad ( Factory
Option )
Built-In TouchPad (with Multi Gesture &
Scrolling Functionality)
Interface
Two USB 2.0 Ports
Two USB 3.0 (USB 3.1 Gen 1) Ports (Type-A)
One USB 3.0 (USB 3.1 Gen 1) Port (Type-C)
===============================
*Note: The maximum amount of current supplied by USB Type-C ports is 500 mA for USB2.0/900 mA for USB 3.1
===============================
One HDM I™ (High-Definition Multimedia
Interface) Out Port (with HDCP)
One External Monitor Port
One S/PDIF Coaxial Out Jack
One Headphone/Speaker-Out Jack
One Microphone-In Jack
One RJ-45 LAN Jack
One DC-In Jack
One USB 3.1 (Gen 2 - Type A) Port &
One USB 3.1 (Gen 2 - Type C) Port
( Factory Option shared with USB 3.0 ports) - 2 * USB 3.1 Gen 2 Ports with
10Gb Shared Bandwidth
D - 2 Specifications
Card Reader
Embedded Multi-In-1 Push-Push Card
Reader
- MMC / RSMMC
- SD / Mini SD / SDHC / SDXC
Card Reader Note: Some of the cards require PC adapters that are usually supplied with the cards.
Slots
Three M.2 Slots:
=======================================
Slot 1: for M.2 2230 WLAN Combo
Module Card with USB Interface (A Key)
Slot 2: for M.2 2280 SSD Card with SATA/
PCIe Gen x3/x4 Interface (M Key)
Slot 3: for LTE or UTMS/HSPA+ M.2 3042
3G or 4G Module Card with USB Interface
(B Key) - ( Factory Option )
Communication
Built-In 10/100/1000Mb Base-TX Ethernet
LAN
1.0M / 2.0M FHD PC Video Camera
Module
Intel ® Dual Band Wireless-AC 8260 (2*2
802.11 a/c) M.2 WLAN + Bluetooth Combo
M.2 2230 Module ( Factory Option )
Intel ® Dual Band Wireless-N 7265 (2*2
802.11 b/g/n) M.2 WLAN + Bluetooth Com- bo M.2 2230 Module ( Factory Option )
Intel ® Dual Band Wireless-AC 3165 (1*1
802.11 ac) WLAN + Bluetooth Combo M.2
2230 Module ( Factory Option )
3rd Party Combo WLAN (802.11b/g/n) and Bluetooth v4.0+LE Combo M.2 2230
Module ( Factory Option )
3G UTMS/HSPA+ M.2 3042 Card Module with USB Interface ( Factory Option )
4G LTE M.2 3042 Card Module with USB
Interface ( Factory Option )
Operating System
Features
Windows
®
10 (64-bit) - UEFI Only
Painted Style
FlexiCharger
Indicators
Specifications
LED Indicators - Power/Suspend, Battery,
HDD/ODD, Airplane Mode, Camera
Security
Security (Kensingto n® Type) Lock Slot
BIOS Password
Intel
®
PTT for Systems without TPM
Trusted Platform Module 2.0 ( Factory Option )
BIOS
One 64Mb SPI Flash ROM
AMI BIOS
Power Management
Supports Wake on LAN (AC Mode Only)
Supports Wake on USB
Supports Wake on RTC Alarm (AC Mode
Only)
Power
Full Range AC/DC Adapter
– AC in 100 -
240V, 50 - 60Hz DC Output 19V, 4.74A
( 65/90 Watts )
Specifications D - 3
D
D
Specifications
Removable 6 Cell Smart Lithium-Ion
Battery Pack 62.16WH ( Factory Option )
Removable 6 Cell Smart Lithium-Ion
Battery Pack 48.84WH ( Factory Option )
Environmental Spec
Temperature
Operating: 5
°
C - 35
°
C
Non-Operating: -2 0°C - 60°C
Relative Humidity
Operating: 20% - 80%
Non-Operating: 10% - 90%
Physical Dimensions & Weight
379mm (w) * 263.4mm (d) * 32.5mm(h)
2.50kg *Barebone System with 48.84WH
Battery
*A barebone system does not include the HDD, RAM, adapter, power cord and factory option modules
(weight tolerance within +/- 5%).
D - 4 Specifications
advertisement
Related manuals
advertisement