Com DCD13019 Instruction Booklet

Parts List

Item Components

A

Qty Item Components

1 F

Qty

4

B

C

D

1 G

2 H

2

Tools Needed (Not Included)

3/16 in. or 5 mm

Safety Hammer Wood Drill Bit Phillips Drill Stud Finder

Glasses Screwdriver

8

1

Note:

before assembly.

Wood Double Stud

16 in

40.64 cm

2

PLEASE CHOOSE BEST INSTALLATION OPTION BASED ON TV BACK PANEL HOLE SPACING:

OPTION 1:

2.95 in x 2.95 in / 75 mm x 75 mm or 3.94 in x 3.94 in / 100 mm x 100 mm

1 2

16”/406mm

Remove TV mounting plate (B) from wall bracket (A).

B

3

A

A

F

This mount is designed to be attached into wood studs.

DO NOT use wall anchors.

Using a stud pencil, mark the hole locations at the desired height, making sure you are level. Use wall bracket (A) as a template to mark the two remaining holes. Drill pilot holes at 4 pencil marks 2.5 in. (64mm) deep, using a

3/16 in. or 5 mm diameter drill bit.

Attach wall bracket (A) to the wall with 4 washers and screws (F).

4

B

Attach TV mounting plate (B) to the back of the TV, by selecting mounting hardware and then using instructions on page 5.

We strongly recommend two people, one on each side, hold the TV. Carefully position the TV over the wall bracket (A) until it locks in place. Tighten safety screws.

3

PLEASE CHOOSE BEST INSTALLATION OPTION BASED ON TV BACK PANEL

HOLES SPACING:

OPTION 2:

(7.87 to 23.6 ) in x 15.7 in / (200 to 600) mm x 400 mm

1

16”/406mm

This mount is designed to be attached into wood studs, DO NOT use wall anchors. using a studs. With a pencil, mark the hole location at the desired height, making sure you are level.

Use wall bracket(A) as a template to mark the two remaining holes. Drill pilot holes at 4 pencil marks 2.5 in. (64mm) deep, using a 3/16 in. or

5 mm diameter drill bit.

Attach wall bracket(A) to the wall with 4 washers and screws(F).

F

A

2

B

D

D

B wrench(H).

4

3

D

D

Figure 1

C

D

Slide TV mounts(C) along with TV horizontal bar(D). See Figure 1 .

Attach Figure 1 to the back of the TV e TV mount(C) and horizontal bar(D) with screws(G) and allen wrench(H).

Selecting mounting hardware and then using instructions on page 7.

4

A safety screws

We strongly recommend two people, one on each side, hold the TV. Carefully postion the TV over the wall bracket(A) until it locks in place. Tighten safety screws.

5

TV Wall Mount

OPTION 1

2.95 in x 2.95 in / 75 mm x 75 mm

3.94 in x 3.94 in / 100 mm x 100 mm

OPTION 2

(7.87 to 23.6) in x 15.7 in

(200 to 600) mm x 400 mm

TAKE EXTRA CARE AND PAY ATTENTION WHEN YOU FASTEN THE TV MOUNT(S) TO THE

BACK TV PANEL IN STEP 3 . MAKE SURE TO USE THE APPROPRIATE MOUNTING HARDWARE

FOR YOUR TV.

1. Select the correct Mounting Hardware according to the screw hole size on your TV. Discard any

remaining screws and spacers.

2. Carefully lay your TV face down on a non-abrasive surface, laying padding underneath it to protect

the screen.

3.

OPTION 1: Place the TV plate (B) in the appropriate position, making sure it is CENTERED on the

back of TV and LEVEL.

OPTION 2: Place the right and left TV mounts in their appropriate positions, making sure they are

CENTERED on the back of the TV and LEVEL with one another.

Mounting Hardware List Q’ty

I

J

K

L

M8 X 16MM

M6 X 12MM

M5 X 12 MM

M4 X 12MM

4

4

4

4

M M8 X 40 MM 4

N

O

M6 X 35MM

M5 X 30MM

4

4

P

M4 X 30MM 4

Q

R

S

Mounting Hardware List Q’ty

M4 / M

5 washer

M6 / M

8 washer

M8 / M6 spacer

4

4

4

T M4 / M5 spacer 4

6

HDMI Cable

Information:

This Kit includes 1 HDMI™ cable

Each HDMI cable measures 6 feet (1828.8 mm) in length.

1.4 Version

Supports Ethernet and 3D

O.D.: 6.0mm

Single molding

7

Distributed by Wal-Mart Stores, Inc.,

Bentonville, AR 72716