advertisement
Specifications
XPA U 1002 Series
Audio
Voltage gain
XPA U 1002 ����������������������������� 23x (27 dB)
XPA U 1002-70V ��������������������� 57x (35 dB)
XPA U 1002-100V ������������������� 81x (38 dB)
CMRR �������������������������������������������� 75 dB @ 1 kHz (typical)
Audio Input
Number/signal type ����������������������� 2 balanced/unbalanced
Connectors ������������������������������������ (1) 3�5 mm captive screw connector, 5 pole
Impedance ������������������������������������ >10k ohms balanced/unbalanced, DC coupled
Nominal level ��������������������������������� +4 dBu, balanced
Maximum level ������������������������������ +20 dBu (7�75 Vrms), balanced
Input sensitivity ������������������������������ +4 dBu
Input signal detection threshold -65 dBu ±3 dB, balanced
NOTE: 0 dBu = 0�775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Audio Output
Number/signal type
XPA U 1002 ����������������������������� 2 channels, 4 or 8 ohms
XPA U 1002-70V ��������������������� 2 channels, 70V
XPA U 1002-100V ������������������� 2 channels, 100V
Connectors ������������������������������������ (1) 5 mm screw lock captive screw connector, 4-pole
NOTE: These connectors accept wires of 22 AWG to 12 AWG�
Load impedance
XPA U 1002 ����������������������������� 4 ohms minimum
XPA U 1002-70V ��������������������� 50 ohms minimum
XPA U 1002-100V ������������������� 100 ohms minimum
Amplifier type ��������������������������������� Class D
Output power
XPA U 1002 ����������������������������� 100 Watts per channel, 8 ohms, 1 kHz, 0�1% THD
100 Watts per channel, 4 ohms, 1 kHz, 0�1% THD
XPA U 1002-70V ��������������������� 100 watts per channel, 70V, 1 kHz, 0�1% THD
XPA U 1002-100V ������������������� 100 watts per channel, 100V, 1 kHz, 0�2% THD
Frequency response ���������������������� 20 Hz to 20 kHz, ±1 dB
THD + Noise ���������������������������������� 0�1% @ 1 kHz, at 3 dB below clipping
S/N ������������������������������������������������ 100 dB, 20 Hz - 20 kHz, unweighted
Damping factor
XPA U 1002 ����������������������������� >100 @ 8 ohms
XPA U 1002-70V ��������������������� >100 @ 50 ohms
XPA U 1002-100V ������������������� >100 @ 100 ohms
Extron XPA U 1002, XPA U 1002-70V, XPA U 1002-100V • Specifications 1
THIS TEXT WINDOW and its contents are for reference only� Delete this material before finishing and releasing the specs sheet� z
Styles are required for proper table placement/formatting (one for the entire specs table as placed within a page [specs table conteiner], two others [ Specs8_Note L1 table and Specs8_Note L2 table ] for the note/caution cells within the specs table)� z
Notes, cautions, and warnings boxes/tables within specs have to be hand inserted and merged and formatted� Use the existing table styles ( NOTE , Caution , and Warning1 ) for the table boxes� z z z
Apply the Specs8_Note L1 table or Specs8_Note L2 table paragraph style
(depending on the content to which the note, caution, or warning applies) to the nested note, caution, or warning table� Also apply the Specs8_Note cell insets cell style to the cell containing the note, caution, or warning nested table�
Apply the Specs8_Note or Specs8_Warning/Caution paragraph style to the text within the nested note, caution, or warning table�
Apply the Specs8_note cell inset cell style to the specs table cell containing the nested table�
Specifications • XPA U 1002 Series (Continued)
High pass filter
XPA U 1002-70V ��������������������� 80 Hz, 12 dB per octave rolloff, selectable via captive screw
XPA U 1002-100V ������������������� 80 Hz, 12 dB per octave rolloff, selectable via captive screw
Control/remote
Control port
XPA U 1002 ����������������������������� (1) 3�5 mm captive screw connector, 2-pole
XPA U 1002-70V ��������������������� (2) 3�5 mm captive screw connector, 2-pole
XPA U 1002-100V ������������������� (2) 3�5 mm captive screw connector, 2-pole
Pin configurations
Standby power control (contact closure) Pin 1 = GND, pin 2 = Standby
High pass filter (contact closure)
General
Pin 1 = GND, pin 2 = OFF
Power supply ��������������������������������� Internal
Input: 100-240 VAC, 50-60 Hz
Power consumption and thermal dissipation
XPA U 1002
AC Line
Current
A
115 VAC, 60Hz
AC Power
Consumed
W
Thermal
Dissipation
W BTU/hr
AC Line
Current
A
230 VAC, 50Hz
AC Power
Consumed
W
Thermal
Dissipation
W BTU/hr Condition
Active (1/8 power), all channels driven
8Ω
4Ω
Quiescent (idle)
Standby
XPA U 1002-70V
0�4
0�4
0�1
<0�1
34�2
35�9
5�3
<1
9�2 31
10�9 37
5�3
<1
18
<3
0�2
0�2
0�1
<0�1
33�5
35�0
5�1
<1
8�5
10�0
5�3
<1
29
34
18
<3
AC Line
Current
A
115 VAC, 60Hz
AC Power
Consumed
Thermal
Dissipation
W W BTU/hr
AC Line
Current
A
230 VAC, 50Hz
AC Power
Consumed
Thermal
Dissipation
W W BTU/hr Condition
Active (1/8 power), all channels driven
70V
Quiescent (idle)
Standby
0�4
0�1
<0�1
36�1
5�5
<1
11�1 38
5�5
<1
19
<3
0�2
0�1
<0�1
35�4
5�4
<1
10�4 35
5�4
<1
18
<3
Extron XPA U 1002, XPA U 1002-70V, XPA U 1002-100V • Specifications 2
Specifications • XPA U 1002 Series (Continued)
XPA U 1002-100V
Condition
Active (1/8 power), all channels driven
100V
AC Line
Current
A
0�4
115 VAC, 60Hz
AC Power
Consumed
W
35�6
Thermal
Dissipation
W
10�6
BTU/hr
36
AC Line
Current
A
0�2
230 VAC, 50Hz
AC Power
Consumed
W
34�9
Thermal
Dissipation
W
9�9
BTU/hr
34
Quiescent (idle) 0�1 5�4 5�4 18 0�1 5�2 5�2 18
Standby
Temperature/humidity
<0�1 <1 <1 <3 <0�1 <1 <1 <3
Storage ����������������������������������� −40 to +158°F (−40 to +70°C) / 10% to 90%, non-condensing
Operating �������������������������������� +32 to +122°F (0 to +50°C) / 10% to 90%, non-condensing
Cooling ������������������������������������ Convection, no vents
Protection �������������������������������������� Clip limiting, thermal, short circuit, DC output
Indication ��������������������������������������� Limiter/Protect LED indicates the onset of clip limiting, thermal cycling, or a short circuit�
Over Temp LED indicates when the amplifier exceeds the recommended operating temperature for optimal unit longevity�
Power LED indicates power state, DC output protection (see XPA Ultra Series
User Guide for details)�
Rack mount ����������������������������������� Yes, with included mounting brackets or optional rack shelf
Enclosure ��������������������������������������� Metal
Enclosure dimensions �������������������� 1�7" H x 8�7" W x 10�5" D (1U high, half rack wide)
43 mm H x 220 mm W x 267 mm D
Product weight ����������������������������� 3�4 lbs (1�5 kg)
Regulatory compliance ������������������� CE, CEC, CISPR 22 Class B, C-tick, CUL, ENERGY STAR®, European Code of
Conduct, FCC Class B, ICES, KC, RoHS, UL, UL 2043, VCCI Class B
Product warranty ��������������������������� 3 years parts and labor
Everlast power supply warranty ������ 7 years parts and labor
NOTE: All nominal levels are at ±10%�
NOTE: Specifications are subject to change without notice�
NOTE: Shipping weights and dimensions are available at www.extron.com
�
5545-D4
© 2022 Extron — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
3
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement