Graco 3A0292C, Xtreme Sprayer Air Control Retrofit Kits Instructions

Instructions-Parts

Xtreme Sprayer Air

Control Retrofit Kits

3A0292C

EN

For replacing the integrated air control module on light and heavy duty Xtreme Sprayer carts. For professional use only.

262230

Air Controls for Light Duty Xtreme Package Carts

262231

Air Controls for Heavy Duty Xtreme Package Carts

100 psi (0.7 MPa, 7 bar) Maximum Working Pressure

Important Safety Instructions

Read all warnings and instructions in this manual.

See your Xtreme Sprayer manual 311164 for complete warnings and instructions. Save these instructions.

262230 on a Light Duty Xtreme Sprayer Cart r_x25dh1_x45dl1_311164_1f

2

Pressure Relief Procedure

Pressure Relief Procedure

4.

Hold gun firmly against a grounded metal pail. Trigger the gun.

1.

Engage gun trigger lock.

TI8252a

TI5049a

2.

Close bleed type master air valve (B).

5.

Engage gun trigger lock.

B

TI8789a

3.

Disengage gun trigger lock.

NOTE: If using an AA gun, turn gun air regulator counter-clockwise to relieve pressure.

TI5049a

6.

Drain fluid. To drain fluid, slowly open all fluid drain valves, including drain/purge valve (J), in system into a waste pail. If there is a return tube, open return line ball valve.

TI5048a

+

J

TI8417a

7.

If you suspect the spray tip or hose is completely clogged, or that pressure has not been fully relieved after following the previous steps, very slowly loosen the tip guard retaining nut or hose end coupling and relieve pressure gradually; then loosen completely. With tip removed, trigger gun into bucket.

3A0292C

Installation

Installation

Remove Integrated Air Control

Module

1.

Relieve pressure. See Pressure Relief Procedure, page 2.

Install 262230 Light Duty Air

Controls

)

)

F ti28466a

F IG . 1: Integrated Air Control Module

2.

Remove safety relief valve (F) and install on the new air control retrofit kit (262230 or 262231).

F IG . 2: Installation

WLD

3A0292C 3

Installation

Install 262231 Heavy Duty Air Controls

1

F

262231

1.1

(28

1 in

.2 m

.

m)

10.4

5 in

. (2

65.4

m m) ti28468a

Drill

0.5 in. (4x)

(12.7 mm)

F

IG

. 3: Installation

2

0.8 in.

(20.3 mm)

0.8

(20

in. m)

F IG . 4: Hose Routing r_x25dh1_x45dl1_3a0292a_5a2

4 3A0292C

Installation

3A0292C 5

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by

Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT

LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy

(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT

MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information

For the latest information about Graco products, visit

www.graco.com

.

For patent information, see

www.graco.com/patents .

TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.

Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

Original instructions. This manual contains English. MM 3A0292

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA

Copyright 2010, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.

www.graco.com

Revision C, February 2016