LiftMaster LA400 1PKGDC, DC, DCS Gate Opener Installation Manual

Below you will find brief information for Gate Opener LA400 LA4001PKGDC, Gate Opener LA400 LA400DC, Gate Opener LA400 LA400DCS. These LiftMaster gate openers are designed for residential use, offering a convenient and secure way to control your vehicular gates. The LA4001PKGDC is a single-arm package ideal for single gates, while the LA400DC and LA400DCS can be used for single or dual gate applications respectively. Each model boasts a 24 VDC actuator arm for smooth operation, compatibility with MyQ® and Security+ 2.0™ accessories.

PDF

Document

TABLE OF CONTENTS

SAFETY 1

SAFETY SYMBOL AND SIGNAL WORD REVIEW .....................................1

USAGE CLASS ..........................................................................................2

UL325 ENTRAPMENT PROTECTION REQUIREMENTS .............................2

SAFETY INSTALLATION INFORMATION ...................................................3

GATE CONSTRUCTION INFORMATION .....................................................4

INTRODUCTION 5

CARTON INVENTORY ...............................................................................5

SPECIFICATIONS ......................................................................................6

SITE PREPARATION .................................................................................7

CHECK YOUR GATE ..................................................................................7

OVERVIEW OF TYPICAL INSTALLATION ..................................................8

INSTALLATION 9

IMPORTANT SAFETY INFORMATION .......................................................9

INSTALLATION TIPS .................................................................................9

ATTACH BRACKETS TO OPERATOR .......................................................10

DETERMINE MOUNTING LOCATION ......................................................11

POSITION THE OPERATOR .....................................................................12

SECURE THE BRACKETS ........................................................................13

INSTALL THE CONTROL BOX .................................................................14

EARTH GROUND ROD ............................................................................16

WIRE THE OPERATOR ARM TO THE CONTROL BOARD ........................16

DUAL GATES ONLY ................................................................................17

INSTALL ENTRAPMENT PROTECTION ...................................................20

POWER WIRING .....................................................................................22

FINISH INSTALL .....................................................................................23

ADJUSTMENT 23

LIMIT AND FORCE ADJUSTMENT ..........................................................23

OBSTRUCTION TEST ..............................................................................25

PROGRAMMING 26

REMOTE CONTROLS (NOT PROVIDED) .................................................26

LIFTMASTER INTERNET GATEWAY

(NOT PROVIDED) ....................................................................................27

ERASE ALL CODES .................................................................................27

ERASE LIMITS ........................................................................................27

TO REMOVE AND ERASE MONITORED ENTRAPMENT PROTECTION

DEVICES .................................................................................................27

OPERATION 28

CONTROL BOARD OVERVIEW ................................................................28

MANUAL RELEASE .................................................................................29

RESET BUTTON ......................................................................................29

PARTY MODE .........................................................................................29

OPERATOR ALARM ...............................................................................30

REMOTE CONTROL ................................................................................30

ACCESSORY WIRING 31

EXTERNAL CONTROL DEVICES ..............................................................31

VEHICLE DETECTION DEVICES ..............................................................31

LOCKS ....................................................................................................32

MISCELLANEOUS WIRING .....................................................................32

MAINTENANCE 33

IMPORTANT SAFETY INFORMATION .....................................................33

MAINTENANCE CHART ...........................................................................33

BATTERIES .............................................................................................33

TROUBLESHOOTING 34

ERROR CODES .......................................................................................34

CONTROL BOARD LEDS .........................................................................37

TROUBLESHOOTING CHART ..................................................................38

APPENDIX 41

BRACKET TYPES ....................................................................................41

SOLAR PANEL(S) ...................................................................................42

LIMIT SETUP WITH A REMOTE CONTROL .............................................47

REPAIR PARTS 48

CONTROL BOX ........................................................................................48

GATE OPERATOR ARM ...........................................................................48

WIRING DIAGRAM 49

STANDARD CONTROL BOX ....................................................................49

ACCESSORIES 50

WARRANTY 51

TEMPLATE FOR POST BRACKET MOUNTING 52

SAFETY

SAFETY SYMBOL AND SIGNAL WORD REVIEW

When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of Serious Injury or Death if you do not comply with the warnings that accompany them. The hazard may come from something mechanical or from electric shock.

Read the warnings carefully.

When you see this Signal Word on the following pages, it will alert you to the possibility of damage to your gate and/or the gate operator if you do not comply with the cautionary statements that accompany it. Read them carefully.

IMPORTANT NOTE:

• BEFORE attempting to install, operate or maintain the operator, you must read and fully understand this manual and follow all safety instructions.

• DO NOT attempt repair or service of your gate operator unless you are an Authorized

Service Technician.

MECHANICAL

ELECTRICAL

SAFETY

USAGE CLASS

CLASS I – RESIDENTIAL VEHICULAR GATE

OPERATOR

A vehicular gate operator (or system) intended for use in garages or parking areas associated with a residence of one-to four single families.

CLASS II – COMMERCIAL/GENERAL ACCESS

VEHICULAR GATE OPERATOR

A vehicular gate operator (or system) intended for use in a commercial location or building such as a multi-family housing unit (five or more single family units), hotel, garages, retail store, or other buildings accessible by or servicing the general public.

CLASS III – INDUSTRIAL/LIMITED ACCESS

VEHICULAR GATE OPERATOR

A vehicular gate operator (or system) intended for use in an industrial location or building such as a factory or loading dock area or other locations not accessible by or intended to service the general public.

CLASS IV– RESTRICTED ACCESS VEHICULAR GATE

OPERATOR

A vehicular gate operator (or system) intended for use in a guarded industrial location or building such as an airport security area or other restricted access locations not servicing the general public, in which unauthorized access is prevented via supervision by security personnel.

I

III

II

IV

UL325 ENTRAPMENT PROTECTION REQUIREMENTS

This vehicular gate operator must be installed with at least two independent entrapment protection means as specified in the table below.

IMPORTANT SAFETY INFORMATION

HORIZONTAL SLIDE AND SWING GATE OPERATOR

Type A

GATE OPERATOR ENTRAPMENT PROTECTION TYPES

Inherent (built into the operator) entrapment protection system

Type B1

Type B2

Non-contact sensors such as photoelectric sensors

Contact sensors such as edge sensors

The same type of device shall not be used for both entrapment protection means. Use of a single device to cover both the opening and closing directions is in accordance with the requirement; however, a single device is not required to cover both directions.

This operator is provided with Type A. The installer is required to install additional entrapment protection devices in each entrapment zone.

To reduce the risk of INJURY or DEATH:

• READ AND FOLLOW ALL INSTRUCTIONS.

• NEVER let children operate or play with gate controls. Keep the remote control away from children.

• ALWAYS keep people and objects away from the gate. NO ONE

SHOULD CROSS THE PATH OF THE MOVING GATE.

• Test the gate operator monthly. The gate MUST reverse on contact with a rigid object or reverse when an object activates the noncontact sensors. After adjusting the force or the limit of travel, retest the gate operator. Failure to adjust and retest the gate operator properly can increase the risk of INJURY or DEATH.

• Use the emergency release ONLY when the gate is not moving.

• KEEP GATES PROPERLY MAINTAINED. Read the owner’s manual.

Have a qualified service person make repairs to gate hardware.

• The entrance is for vehicles ONLY. Pedestrians MUST use separate entrance.

• SAVE THESE INSTRUCTIONS.

SAFETY

SAFETY INSTALLATION INFORMATION

1. Vehicular gate systems provide convenience and security. Gate systems are comprised of many component parts. The gate operator is only one component. Each gate system is specifically designed for an individual application.

2. Gate operating system designers, installers and users must take into account the possible hazards associated with each individual application. Improperly designed, installed or maintained systems can create risks for the user as well as the bystander. Gate systems design and installation must reduce public exposure to potential hazards.

3. A gate operator can create high levels of force in its function as a component part of a gate system. Therefore, safety features must be incorporated into every design. Specific safety features include:

• Edges Sensors (contact) • Guards for Exposed Rollers

• Photoelectric Sensors • Screen Mesh

• Vertical Posts • Instructional and Precautionary Signage

4. Install the gate operator only when: a. The operator is appropriate for the construction and the usage class of the gate.

b. All openings of a horizontal slide gate are guarded or screened from the bottom of the gate to a minimum of 6 feet (1.8 m) above the ground to prevent a 2-1/4 inches (6 cm) diameter sphere from passing through the openings anywhere in the gate, and in that portion of the adjacent fence that the gate covers in the open position.

c. All exposed pinch points are eliminated or guarded, and guarding is supplied for exposed rollers.

5. The operator is intended for installation only on gates used for vehicles. Pedestrians must be supplied with a separate access opening. The pedestrian access opening shall be designed to promote pedestrian usage. Locate the gate such that persons will not come in contact with the vehicular gate during the entire path of travel of the vehicular gate.

6. The gate must be installed in a location so that enough clearance is supplied between the gate and adjacent structures when opening and closing to reduce the risk of entrapment. Swinging gates shall not open into public access areas.

7. The gate must be properly installed and work freely in both directions prior to the installation of the gate operator.

8. Controls intended for user activation must be located at least 6 feet

(1.8 m) away from any moving part of the gate and where the user is prevented from reaching over, under, around or through the gate to operate the controls. Outdoor or easily accessible controls shall have a security feature to prevent unauthorized use.

Exception: Emergency access controls only accessible by authorized personnel (e.g. fire, police) may be placed at any location in the line-of-sight of the gate.

9. The Stop and/or Reset (if provided separately) must be located in the line-of-sight of the gate. Activation of the reset control shall not cause the operator to start.

10. A minimum of two (2) WARNING SIGNS shall be installed, one on each side of the gate where easily visible.

11. For a gate operator utilizing a non-contact sensor: a. Reference owner’s manual regarding placement of non-contact sensor for each type of application. See Install Entrapment

Protection section.

b. Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle trips the sensor while the gate is still moving.

c. One or more non-contact sensors shall be located where the risk of entrapment or obstruction exists, such as the perimeter reachable by a moving gate or barrier.

12. For a gate operator utilizing a contact sensor such as an edge sensor: a. One or more contact sensors shall be located where the risk of entrapment or obstruction exists, such as at the leading edge, trailing edge and post mounted both inside and outside of a vehicular horizontal slide gate.

b. A hard wired contact sensor shall be located and its wiring arranged so the communication between the sensor and the gate operator is not subject to mechanical damage.

c. A wireless device such as one that transmits radio frequency (RF) signals to the gate operator for entrapment protection functions shall be located where the transmission of the signals are not obstructed or impeded by building structures, natural landscaping or similar obstruction. A wireless device shall function under the intended end-use conditions.

d. One or more contact sensors shall be located on the inside and outside leading edge of a swing gate. Additionally, if the bottom edge of a swing gate is greater than 6 inches (152 mm) above the ground at any point in its arc of travel, one or more contact sensors shall be located on the bottom edge.

e. One or more contact sensors shall be located at the bottom edge of a vertical barrier (arm).

SAFETY

GATE CONSTRUCTION INFORMATION

Vehicular gates should be installed in accordance with ASTM F2200: Standard Specification for Automated Vehicular Gate Construction. For a copy, contact ASTM directly at 610-832-9585 or www.astm.org.

1. GENERAL REQUIREMENTS

1.1 Gates shall be constructed in accordance with the provisions given for the appropriate gate type listed, refer to ASTM F2200 for additional gate types.

1.2 Gates shall be designed, constructed and installed to not fall over more than 45 degrees from the vertical plane, when a gate is detached from the supporting hardware.

1.3 Gates shall have smooth bottom edges, with vertical bottom edged protrusions not exceeding 0.50 inches (12.7 mm) when other than the exceptions listed in ASTM F2200.

1.4 The minimum height for barbed tape shall not be less than 8 feet

(2.44 m) above grade and for barbed wire shall not be less than 6 feet (1.83 m) above grade.

1.5 An existing gate latch shall be disabled when a manually operated gate is retrofitted with a powered gate operator.

1.6 A gate latch shall not be installed on an automatically operated gate.

1.7 Protrusions shall not be permitted on any gate, refer to ASTM

F2200 for Exceptions.

1.8 Gates shall be designed, constructed and installed such that their movement shall not be initiated by gravity when an automatic operator is disconnected, in accordance with the following.

1.8.1 Vehicular horizontal slide gate. Shall not result in continuous, unimpeded movement in either lineal direction of its travel.

1.8.2 Vehicular horizontal swing gate. Shall not result in continuous, unimpeded movement in either direction along the arc of its path of travel.

1.9 For pedestrian access in the vicinity of an automated vehicular gate, a separate pedestrian gate shall be provided. The pedestrian gate shall be installed in a location such that a pedestrian shall not come in contact with a moving vehicular access gate. A pedestrian gate shall not be incorporated into an automated vehicular gate panel.

2. SPECIFIC APPLICATIONS

2.1 Any non-automated gate that is to be automated shall be upgraded to conform to the provisions of this specification.

2.2 This specification shall not apply to gates generally used for pedestrian access and to vehicular gates not to be automated.

2.3 Any existing automated gate, when the operator requires replacement, shall be upgraded to conform to the provisions of this specification in effect at that time.

3. VEHICULAR HORIZONTAL SLIDE GATES

3.1 The following provisions shall apply to Class I, Class II and Class

III vehicular horizontal slide gates:

3.1.1 All weight bearing exposed rollers 8 feet (2.44 m), or less, above grade shall be guarded or covered.

3.1.2 All openings shall be designed, guarded, or screened from the bottom of the gate to the top of the gate or a minimum of 72 in.

(1.83 m) above grade, whichever is less, to prevent a 2 1⁄4 in.

(57 mm) diameter sphere from passing through the openings anywhere in the gate, and in that portion of the adjacent fence that the gate covers in the open position. The gate panel shall include the entire section of the moving gate,including any back frame or counterbalance portion of the gate.

3.1.3 A gap, measured in the horizontal plane parallel to the roadway, between a fixed stationary object nearest the roadway, (such as a gate support post) and the gate frame when the gate is in either the fully open position or the fully closed position, shall not exceed 2 1/4 inches (57 mm), refer to ASTM F2200 for Exception.

3.1.4 Positive stops shall be required to limit travel to the designed fully open and fully closed positions. These stops shall be installed at either the top of the gate, or at the bottom of the gate where such stops shall horizontally or vertically project no more than is required to perform their intended function.

3.1.5 All gates shall be designed with sufficient lateral stability to assure that the gate will enter a receiver guide, refer to ASTM

F2200 for panel types.

3.2 The following provisions shall apply to Class IV vehicular horizontal slide gates:

3.2.1 All weight bearing exposed rollers 8 feet (2.44 m), or less, above grade shall be guarded or covered.

3.2.2 Positive stops shall be required to limit travel to the designed fully open and fully closed positions. These stops shall be installed at either the top of the gate, or at the bottom of the gate where such stops shall horizontally or vertically project no more than is required to perform their intended function.

4. VEHICULAR HORIZONTAL SWING GATES

4.1 The following provisions shall apply to Class 1, Class II and Class

III vehicular horizontal swing gates:

4.1.1 Gates shall be designed, constructed and installed so as not to create an entrapment area between the gate and the supporting structure or other fixed object when the gate moves toward the fully open position, subject to the provisions in 4.1.1.1 and

4.1.1.2.

4.1.1.1 The width of an object (such as a wall, pillar or column) covered by a swing gate when in the open position shall not exceed 4 inches (102 mm), measured from the center line of the pivot point of the gate, refer to ASTM F2200 for exception.

4.1.1.2 Except for the zone specified in Section 4.1.1.1, the distance between a fixed object such as a wall, pillar or column, and a swing gate when in the open position shall not be less than 16 inches (406 mm), refer to ASTM F2200 for exception.

4.2 Class IV vehicular horizontal swing gates shall be designed, constructed and installed in accordance with security related parameters specific to the application in question.

INTRODUCTION

CARTON INVENTORY

NOT SHOWN: Documentation packet

LA400DC

Pull-to-Open Bracket

Gate Bracket

Standard Control Box with 2 Batteries and hardware bag (watertight connector (4),

30 amp fuse (2), mounting bolt, washer (4), and wire nut (3))

Pull-to-Open Bracket

Gate Bracket

Plug-in Transformer

Post Bracket

Gate Operator

(with a 6 foot cable attached)

Warning Signs (2)

HARDWARE INVENTORY

NOTE: Hardware quantities shown below are for LA400DC. Quantities are doubled for LA400DCS.

Gate Operator

LA400DCS ONLY

Motor Cable

Six Conductor,

40 feet (12.2 m)

Post Bracket

Terminal Block

Junction Box

Connector

Flat Washer 5/16" (1) Hex Nut 5/16"-18 (1)

Keylock Cap

Lock Washer 5/16" (1)

Hex Bolt 5/16"-18 x 1-1/2" (1) Hex Bolt 3/8"-16 x 1-1/2" (1)

Hex Nut 3/8"-16 (3) Carriage Bolt 3/8" x 5-15/16" (2)

OPTIONAL ACCESSORIES (ORDERED SEPARATELY)

Push-to-Open Bracket (Model 50-19503)

If your application requires the gate to be pushed open, a push-to-open bracket is required (refer to accessories).

Expansion Board (Model K1D8080-1CC)

Large Metal Control Box for Solar Applications

(Model XLSOLARCONTDC)

Required for solar installations (batteries not included). Requires two

33AH batteries, battery tray, and solar battery harness (refer to accessories).

Key (2)

Pin (2)

Flat Washer 3/8" (3)

Hairpin Clip (2)

Lock Washer 3/8" (3)

INTRODUCTION

SPECIFICATIONS

This model is intended for use in vehicular swing gate applications:

Usage Classification

Main AC Supply

System Operating Voltage

Class I, II, & III

120 Vac, .5 Amps (6.5 Amps including Accessory Outlets)

24 Vdc Battery Run / Direct Plug-in Transformer Charge

Accessory Power

Solar Power Max

Maximum Gate Weight/Length

90 Degree Travel Time*

Maximum Travel Range*

Maximum Daily Cycle Rate

Maximum Duty Cycle

24 Vdc, 500mA max. for ON + SW (switched)

24 Vdc at 60 watts max.

850 lbs. (385.6 kg) / 10 ft (3.0 m)

750 lbs. (340.2 kg) / 12 ft (3.7 m)

650 lbs. (294.8 kg) / 14 ft (4.3 m)

550 lbs. (249.5 kg) / 16 ft (4.9 m)

15-18 seconds

115 degrees

100 cycles / day

4 min on

Operating Temperature

Expansion Board

Inherent Entrapment Protection (Type A)

-20°C to 60°C (-4°F to 140°F)

Optional

Dual - RPM and Current Sense

External Entrapment Protection (Type B1 and/or Type B2) 3 inputs per board - any combination of up to 3 photoelectric sensors and up to 2 edge sensors

*Travel time and range are affected by A and B mounting dimensions

Standard Control Box Large Metal Control Box

4-1/2"

(11.2 cm)

(10.2 cm)

1/4"

(0.635 cm)

Weight: 13.2 lbs. (6 kg.)

36-5/16"

(92.2 cm)

1/2" DIA.

(1.3 cm DIA.)

37-3/8"

(94.9 cm)

53-1/2"

(136 cm)

16-7/16"

(41.8 cm)

14-3/8"

(36.5 cm)

6-9/16"

(16.7 cm)

20-3/4"

(52.7 cm)

17-3/16"

(43.7 cm)

6-3/16"

(15.7 cm)

INTRODUCTION

SITE PREPARATION

Check the national and local building codes BEFORE installation.

TRENCH

Trench and install conduit. Before trenching, contact underground utility locating companies. Conduit must be UL approved for low and high voltage.

LOOPS

Loops allow the gate to stay open when vehicles are obstructing the gate path. Suggested for vehicles 14 feet (4.27 m) or longer. Loops are not required but are recommended.

Conduit

SAFETY

Entrapment protection devices are required to protect against any entrapment or safety conditions encountered in your gate application (refer to pages 19-20 for more details). Install warning signs on both sides of the gate.

(Inside Property)

GATE

Gate must be constructed and installed according to ASTM F2200 standards (refer to page 4). Gate must fit specifications of operator

(refer to specifications).

Warning Signs

Entrapment Danger

CHECK YOUR GATE

Gate MUST be level. Gate and gate post MUST be plumb. Gate MUST have a smooth bottom edge, no protrusions should exist.

Remove ANY/ALL wheels from the bottom of gate.

Gate MUST NOT hit or drag across ground.

Gate MUST swing freely and be supported entirely by its hinges.

INTRODUCTION

OVERVIEW OF TYPICAL INSTALLATION

Identify your installation type (refer to the Appendix in the back of the manual for more information). All the illustrations on the following pages display a typical Left-Hand Gate installation with a pull-to-open bracket. For Push-to-Open applications refer to the Appendix.

SINGLE GATE

Control Box

Warning Sign

Operator

Photoelectric

Sensors

NOTE: One or more non-contact sensors shall be located where the risk of entrapment or obstruction exists at either the opening or closing direction. Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle, trips the sensor while the gate is still moving.

Photoelectric

Sensors

Edge Sensors

Water Tight Conduit (Not provided)

NOTE: Power and control wiring

MUST be run in separate conduits.

Earth Ground Rod

Check national and local codes for proper depth

DUAL GATE

Photoelectric

Sensors

Warning Sign

Edge Sensor

Secondary Operator

Junction

Box

Control Box

Primary Operator

Warning Sign

Photoelectric Sensors

Photoelectric

Sensors

Water Tight Conduit (Not provided)

NOTE: Power and control wiring

MUST be run in separate conduits.

Earth Ground Rod

Check national and local codes for proper depth

Edge Sensor

Photoelectric Sensors

INSTALLATION

IMPORTANT SAFETY INFORMATION

To prevent SERIOUS INJURY or DEATH from a moving gate:

• Pinch points must be guarded at all times. Install enclosed-style gate tracks and roller guards.

• Place screen mesh 6 feet (1.8 m) high on the gate to prevent access through openings anywhere the gate may travel.

• Mount controls at least 6 feet (1.8 m) from the gate or ANY moving part of the gate.

• Install Warning signs on EACH side of gate in PLAIN VIEW.

Permanently secure each Warning sign in a suitable manner using fastening holes.

• This operator is intended for vehicular use only. To prevent INJURY to pedestrians, a separate pedestrian access should be supplied, visible from the gate. Locate the pedestrian access where there is not a chance of INJURY at any point during full movement of the gate.

• Contact sensors MUST be located at the leading and trailing edges, and post mounted both inside and outside a horizontal swing gate.

Non-contact sensors such as photoelectric sensors MUST be mounted across the gate opening and operate during BOTH the open and close cycles.

• Entrapment protection devices MUST be installed to protect anyone who may come near a moving gate.

• Locate entrapment protection devices to protect in BOTH the open and close gate cycles.

• Locate entrapment protection devices to protect between moving gate and RIGID objects, such as posts or walls.

• Too much force on gate will interfere with proper operation of safety reversal system.

• NEVER increase force beyond minimum amount required to move gate.

• NEVER use force adjustments to compensate for a binding or sticking gate.

• If one control (force or travel limits) is adjusted, the other control may also need adjustment.

• After ANY adjustments are made, the safety reversal system MUST be tested. Gate MUST reverse on contact with a rigid object.

• To AVOID damaging gas, power or other underground utility lines, contact underground utility locating companies BEFORE digging more than 18 inches (46 cm) deep.

• ALWAYS wear protective gloves and eye protection when changing the battery or working around the battery compartment.

INSTALLATION TIPS

DO's

• Weld a horizontal bar across entire gate on any installation for strength. Make sure that the operator is mounted level or it will not function properly.

• Make sure there is slack in the operator cable.

• The operator can be mounted on top of the gate frame.

• The operator must be installed at least 12 inches from the ground.

Operator Cable

DON'Ts

• DO NOT install upside down.

• DO NOT install next to sprinklers or any area that may expose the bottom of operator to water.

• DO NOT install on uphill or downhill gates.

• DO NOT install on ANY pedestrian passageways, doorways, or gates.

• DO NOT over-bend the operator cable. Doing this will cause the wires to eventually break.

• DO NOT weld the crossbar on just a few pickets, or they could bend.

INSTALLATION

STEP 1

ATTACH BRACKETS TO OPERATOR

1. Insert the key into the lock on the release lever and turn it 180° counterclockwise.

2. Turn the release lever 180° counterclockwise. The operator is now in manual mode.

3. Assemble gate post bracket by placing pull-to-open bracket on top of post bracket.

4. Insert the bolt through both brackets and secure with washer, lock washer and nut.

5. Attach post bracket assembly to operator using pins and hairpin clips.

6. Attach gate bracket to operator using pins and hairpin clips.

Hex Bolt 3/8"

Extension

Bracket

Post Bracket

Washer

Lock Washer

Nut

Release Lever

Post Bracket Assembly

Hairpin Clip

Gate Bracket

INSTALLATION

STEP 2

DETERMINE MOUNTING LOCATION

MEASURING AND MARKING FOR THE GATE BRACKET

Before proceeding, begin with the gate in the fully closed position. There are two methods for determining the proper location of the post brackets:

• Paper template (Located on the back page of this manual. Must be cut out.)

Either method will work depending on preference.

NOTE: There should only be a maximum of 4" (10.2 cm) from the center of the hinge to the edge of the post or column. If the distance is greater than

4" (10.2 cm) entrapment protection for this area is required.

TEMPLATE METHOD

1. Close the gate.

2. Place the template (provided on the back page of this manual) under the center of the gate hinge point.

3. Use a screwdriver or dowel rod to temporarily mark the location in front of the gate post.

TEMPLATE METHOD

TOP VIEW

Gate Post

Gate Hinge Point

4" (10.2 cm) maximum

Gate

TAPE MEASURE METHOD

1. Close the gate.

2. Place the measuring tape under the center of the gate hinge point and measure out 7 inches (17.8 cm).

3. Use a screwdriver or dowel rod to temporarily mark the location of the first measurement.

4. Measure 7 inches (17.8 cm) from the previous mark.

5. Use the screwdriver or dowel rod to mark the location of the second measurement.

ALTERNATE DIMENSIONS

The ideal installation measurements are A = 7" (17.8 cm) and B = 7"

(17.8 cm). If different measurements are used, the sum of A and B cannot be greater than 15" (38.1 cm).

A

DIMENSION CHART

B

7" (17.8 cm)

8" (20.3 cm)

7-1/2" (19.1 cm)

6-1/2" (16.5 cm)

6" (15.2 cm)

7" (17.8 cm)

6" (15.2 cm)

7-1/2" (19.1 cm)

6-1/2" (16.5 cm)

6" (15.2 cm)

TAPE MEASURE METHOD

TOP VIEW

Gate Post

4" (10.2 cm) maximum

Gate Hinge Point

Gate

7" (17.8 cm)

ALTERNATE DIMENSIONS

Gate Hinge Point

Gate Post Gate

(A)

(B)

INSTALLATION

STEP 3

POSITION THE OPERATOR

NOTE: The post bracket assembly can be mounted several places on the gate post.

1. Open the gate to desired open position (no greater than 100°) and hold operator against gate.

2. Place the operator arm against gate post at the desired position.

Temporarily secure gate post bracket with clamp. The gate operator

(arm) must be level.

3. Mark mounting holes on gate for reference. Temporarily secure the gate bracket using a clamp.

4. Align the pull-to-open bracket to a position as CLOSE AS POSSIBLE above the screwdriver or dowel rod.

5. Insert hex bolt through pull-to-open bracket and post bracket and secure with washer, lock washer and nut.

Screwdriver

TEST GATE TRAVEL

NOTE: If gate does not open and close completely adjust the position of the gate bracket and mark new mounting holes.

1. Manually open and close the gate.

2. Ensure that the operator does not bind against the pull-to-open bracket.

3. Ensure that the piston does not bottom out.

1/2" (1.3 cm)

Do not allow piston to fully extend or fully retract.

1/2" (1.3 cm)

INSTALLATION

STEP 4

SECURE THE BRACKETS

POST BRACKET

The gate operator (arm) must be level.

1. Mark holes for the post bracket. Remove the clamp and the operator, set aside.

2. Drill adequate holes in the gate post.

3. Secure the post bracket to the gate post using hardware.

GATE BRACKET

The gate operator (arm) must be level.

Some installations may require additional reinforcement be installed on the gate.

1. Drill holes in gate (or reinforcement, if necessary) that are large enough for the gate bracket mounting hardware.

2. Secure the gate operator to the gate using hardware (not provided).

3. Manually move the gate to verify that it opens and closes fully.

Welder (Optional)

Hex Nuts

Lock

Washers

Flat Washers

Post Bracket

Carriage Bolts

Hex Bolt

Gate Bracket

Reinforcement Area

Flat Bar

Hex Nut

Lock Washer

Flat Washer

Welder (Optional)

Angle

Iron

Wood

INSTALLATION

STEP 5

INSTALL THE CONTROL BOX

For Large Metal Control Box installation, refer to the following page.

STANDARD CONTROL BOX

The control box MUST be mounted within 5 feet (1.52 m) of the gate operator. Mount the control box as high as possible for best radio reception. Make sure the control box is level.

1. Remove the screws and open the control box.

2. Select the mounting holes (according to your application) and remove the knockouts using a screwdriver and hammer.

3. Secure the control box to mounting surface.

A. Wall or Column: Use the provided screws (4).

B. Post: Use U-bolts and rubber washers (not provided) to ensure a watertight seal. Make sure the U-bolts do not protrude more than

3/4 inch from the control box because this can short the control board.

WALL OR COLUMN MOUNT

9 1/8"

13 3/4"

POST MOUNT

6 3/8"

4 3/8"

3 7/8"

5 7/8"

4 7/8"

2 7/8"

12 1/16"

INSTALLATION

STEP 5 continued...

INSTALL THE CONTROL BOX

LARGE METAL CONTROL BOX (XLSOLARCONTDC)

The control box MUST be mounted within 5 feet (1.52 m) of the gate operator. Mount the control box as high as possible for best radio reception. Make sure the control box is level.

WALL OR COLUMN MOUNT

1. Open the control box. The control box door may be removed by opening the door 90°. Lift the door from the hinges and set aside until the installation is complete.

2. Use knock outs located at the 4 corners of the control box and knock out using a screwdriver and hammer.

3. Secure the control box to mounting surface using the provided screws (4).

WALL OR COLUMN MOUNT

POST MOUNT

POST MOUNT

NOTE: The post mount option is not recommended for the 33AH battery application.

1. Open the control box. The control box door may be removed by opening the door 90°. Lift the door from the hinges and set aside until the installation is complete.

2. The control box can be mounted to a post with 'U' bolts (refer to chart). The knock out will accommodate a 3/8" diameter 'U' bolt.

Select center mounting holes (top and bottom) and knock out using a screwdriver and hammer.

3. Secure the control box to mounting surface with U-bolts and rubber washers (not provided) to ensure a watertight seal.

TYPE AND SIZE

Standard 3" Round Pipe

Standard 4" Square Post

Standard 6" Square Post

'U' BOLT OPENING

3-1/2"

INSTALLATION

To reduce the risk of SEVERE INJURY or DEATH:

• ANY maintenance to the operator or in the area near the operator

MUST NOT be performed until disconnecting the electrical power (AC or solar and battery) and locking-out the power via the operator power switch. Upon completion of maintenance the area MUST be cleared and secured, at that time the unit may be returned to service.

• Disconnect power at the fuse box BEFORE proceeding. Operator

MUST be properly grounded and connected in accordance with national and local electrical codes. NOTE: The operator should be on a separate fused line of adequate capacity.

• ALL electrical connections MUST be made by a qualified individual.

• DO NOT install ANY wiring or attempt to run the operator without consulting the wiring diagram. We recommend that you install an edge sensor BEFORE proceeding with the control station installation.

• ALL power wiring should be on a dedicated circuit and well protected. The location of the power disconnect should be visible and clearly labeled.

• ALL power and control wiring MUST be run in separate conduit.

STEP 6

EARTH GROUND ROD

Use the proper earth ground rod for your local area. The ground wire must be a single, whole piece of wire. Never splice two wires for the ground wire. If you should cut the ground wire too short, break it, or destroy its integrity, replace it with a single wire length.

1. Install the earth ground rod within 3 feet of the control box.

2. Run wire from the earth ground rod to the control box. The earth ground wire will be connected in a later step.

NOTE: If the operator is not grounded properly the range of the remote controls will be reduced.

Control Box

12 Gauge Wire

Check national and local codes for proper depth

Earth Ground Rod (Within 3'

(0.9 m) of control box)

STEP 7

WIRE THE OPERATOR ARM TO THE

CONTROL BOARD

1. Choose a knockout in the bottom of the control box.

2. Insert the operator cable through the provided watertight connector.

3. Insert the operator cable and watertight connector into the knockout.

4. Slide the connector nut onto the operator cable.

5. Connect the operator cable wires to the connector according to the colored label on the connector (white to white, red to red, etc.).

6 Plug the connector into the GATE 1 terminal on the control board as shown.

If installing one operator, proceed to page 19. If installing two operators, go to the following page.

(control board)

Connector

Operator Cable

Watertight

Connector

Nut

INSTALLATION

STEP 8

DUAL GATES ONLY

There are two options for dual gate communication: wired or wireless. Follow the directions according to your application. Do not use wired and

wireless communication simultaneously. Wired dual gate applications will have a longer battery standby time than wireless applications. Wireless dual gates will require the installation of two control boxes, one for each operator arm.

WIRELESS DUAL GATES

INSTALL A SECOND OPERATOR ARM AND CONTROL

BOX

Install a second operator arm and control box by following installation steps 1-7.

TO ACTIVATE THE WIRELESS FEATURE

1. Choose a control box to be the network primary operator. All wireless accessories will need to be programmed to the primary control board.

NOTE: We recommend that all accessories and board configurations are set on the primary control board.

2. Press and release the LEARN button on the primary control board.

The green XMITTER LED will light.

3. Press and release the LEARN button again on the primary control board. The yellow NETWORK LED will light.

4. Press and release the OPEN test button to assign this operator as network primary.

5. Press and release the LEARN button on the secondary control board.

The green XMITTER LED will light.

6. Press and release the LEARN button again on the secondary control board. The yellow NETWORK LED will light.

7. Press and release the CLOSE test button to assign this operator as network secondary.

Both operators will beep and the yellow NETWORK LEDs will turn off indicating programming is successful.

TO DEACTIVATE THE WIRELESS FEATURE:

1. Press and release the LEARN button on either control board. The green XMITTER LED will light.

2. Press and release the LEARN button again on the same control board.

The yellow NETWORK LED will light.

3. Press and hold the LEARN button for 5 seconds. The yellow

NETWORK LED will blink (operator will beep) then turn off indicating successful deactivation.

Repeat the steps for the other control board.

Inju ry or Death

Moving Gate Can Cause

Gate may move at any

KEEP CLEAR! time without prior warning.

Do not let chi play in the gate a

This entrance is for vehicles only

Pedestria ns must use separate entrance

LEARN T

BUT

XMITTER

NETWORK

REVERSAL

FORCE

XMITTER

NETWORK

RSAL

RCE

TEST

BUTTONS move at any

Injury or Death

Gate may

KEEP CLEAR! time without prior warning.

Do not let children operate the gate or play in the gate area.

This entrance is for vehicles only

Pedestrians must use separate entrance

MAX

INSTALLATION

STEP 8 continued...

DUAL GATES ONLY

WIRED DUAL GATES

INSTALL A SECOND OPERATOR ARM

Install a second operator arm by following installation steps 1-4.

INSTALL THE EXTENSION CABLE AND JUNCTION

BOX

Before digging, contact local underground utility locating companies.

1. Trench across driveway to bury the extension cable. Use PVC conduit to prevent damage to cables.

2. Open the junction box by removing screws (4) and set aside.

3. Select holes to be used for mounting and knock out using a screwdriver and hammer. Drill two holes in the bottom of the junction box large enough for the watertight connectors.

4. Mount the junction box within 3 feet (0.9 m) of second operator.

5. Route operator cable and extension cable through watertight connector nut and watertight connector.

6. Insert the cables and watertight connectors into the holes in the bottom of the junction box.

7. Slide the connector nut onto the operator cable and extension cable.

8. Connect the wires from extension cable and operator cable to the terminal block connector as shown (like-colored wires must face each other).

9. Put wires inside of junction box.

10. Secure operator and extension cables by tightening the connector nut.

11. Reinstall cover.

Operator

Cable

Connector Nut

Watertight

Connector

Connector Nut

Mounting Slot

Brown

Green

White

Yellow

Blue

Red

Terminal Block

Brown

Green

White

Yellow

Blue

Red

Operator

Cable Extension

Cable

Within 3' (0.9 m)

Extension

Cable

Injury or Death or

Gate may move at any

KEEP CLEAR! rea.

This entrance is for ve

Pede hicles only

Do not let children operate the gate play in the gate a strians must use separate entrance ath

Injury or De

Gate may move at any

KEEP CLEAR! tim hicles only

This entrance is for ve

Pedestrian e separate entrance play in the gate area.

s must us

PVC Conduit

INSTALLATION

STEP 8 continued...

DUAL GATES ONLY

WIRED DUAL GATES

WIRE THE SECONDARY OPERATOR ARM TO THE

CONTROL BOARD

1. Choose a knockout in the bottom of the control box.

2. Insert the extension cable through the watertight connector.

3. Insert the extension cable and watertight connector into the knockout.

4. Slide the connector nut onto the operator cable.

5. Connect the extension cable wires to the connector according to the colored label on the connector (white to white, red to red, etc.).

6. Plug the connector into the GATE 2 terminal on the control board as shown.

Watertight

Connector

Extension

Cable

Connector Nut

(Control Board)

Connector

Mo vin

KE time

This

EP not

in t

entr g Ga

Inju

AR t pr he g area e is for

Ped estr mu te m

! Ga te C an r De ay m arni ren ope

veh se s ath ove ng.

Cau se

the gate s on icle

at a

entr

or anc

CLE AR

KE EP

Do play

This

Ped vin with not

in t estr g G

Inj ury out he g

mu ians

! Gat ate is fo

Ca n C aus

De e m r veh ath s on icle at an parat e en e or ren ope

the gat tran st u se se

Primary Operator

Secondary Operator

SET THE BIPART DELAY (SINGLE CONTROL BOX)

Occasionally in dual gate installations, one gate will need to open first and close second. This would happen if there was an ornamental overhang on one gate or if using a solenoid lock, for example. This gate is called the

Primary gate and needs to be connected to Gate 1 connections on the control board. Thus, it is preferred that the control box be installed on the same side as this gate. If there is no appropriate location on that side for the control box, then mount the control box on the opposite side, but connect the operator closest to the control box to the Gate 2 connector and the operator on the opposite side to the Gate 1 connector.

1. The BIPART DELAY switch on the control board needs to be set to the ON position.

The following illustration shows a dual gate configuration with a decorative overlapping piece on the outside of the gate.

Primary Gate OUTSIDE PROPERTY

SET THE BIPART DELAY (DUAL CONTROL BOX)

BIPART DELAY/SYNCHRONIZED CLOSE

The LOCK/BIPART DELAY switch is used with dual control box applications and serves two functions:

• BIPART DELAY: The BIPART DELAY is used in applications where a mag-lock, solenoid lock, or decorative overlay would require one gate to close before the other. The control box with the LOCK/BIPART

DELAY switch ON will delay from the close limit when opening and be the first to close from the open limit.

• SYNCHRONIZED CLOSE: The BIPART DELAY is also used in applications where one gate travels a longer distance than the other.

To synchronize the closing of the gates, set the LOCK/BIPART DELAY switch to ON for both control boxes.

Primary Gate - Connect to Gate 1 Connector on Control Board.

INSTALLATION

To prevent SERIOUS INJURY or DEATH from a moving gate:

• Entrapment protection devices MUST be installed to protect anyone who may come near a moving gate.

• Locate entrapment protection devices to protect in BOTH the open and close gate cycles.

• Locate entrapment protection devices to protect between moving gate and RIGID objects, such as posts or walls.

STEP 9

INSTALL ENTRAPMENT PROTECTION

At least one external monitored entrapment protection device is required prior to gate movement (effective January of 2016). A monitored device sends a pulsed signal to the operator so the operator is aware of the device. If the operator does not receive the signal from the device it will not run.

An entrapment zone is every location or point of contact where a person can become entrapped between a moving gate and a stationary object. All gate operator systems REQUIRE two independent entrapment protection systems for each entrapment zone. This operator contains an inherent

(internal) entrapment protection system and REQUIRES the addition of an external entrapment protection system (non-contact photoelectric sensor or contact edge sensor) for EACH entrapment zone.

Your application may contain one or many entrapment zones. Property owners are obligated to test entrapment protection devices monthly.

NON-CONTACT SENSORS

If the photoelectric sensor beam gets blocked while the gate is moving, the gate will stop and reverse for 4 seconds. The gate will not be able to travel in that direction until the obstruction is cleared. CPS-UN4 or CPS-RPEN4GM monitored photoelectric sensors MUST be used. If a monitored photoelectric sensor is not working or loses power or the beam is blocked, then ALL gate operation in that direction will stop.

Monitored Photoelectric Sensors

(Outside Property)

Sensors for Open Cycle

NOTE: If the distance between the open gate and the wall is less than

16" (40.6 cm) entrapment protection for this area is required.

(Inside Property)

Sensors for Close Cycle

INSTALLATION

STEP 9 continued...

INSTALL ENTRAPMENT PROTECTION

There are three options for wiring the entrapment protection devices depending on the specific device and how the device will function. Refer to the wiring diagram or the specific entrapment protection device manual for more information. These entrapment protection device inputs are for monitored devices, which include pulsed photoelectric sensors, resistive edge sensors, and pulsed edge sensors. NOTE: Only one monitored entrapment protection device may be wired to each input.

CLOSE EYES/INTERRUPT

(2 Terminals)

The CLOSE EYES/INTERRUPT input is for photoelectric sensor entrapment protection for the close direction. When an obstruction is sensed during gate closing the gate will open to the full open position and resets the Timer-to-Close. This input will be disregarded during gate opening.

CLOSE EDGE

(2 Terminals)

The CLOSE EDGE input is for edge sensor entrapment protection for the close direction. When an obstruction is sensed during gate closing the gate will reverse for 4 seconds then stop, disengaging the Timer-to-Close.

This input will be disregarded during gate opening.

OPEN EYES/EDGE

(2 Terminals)

The OPEN EYES/EDGE input is for photoelectric sensor or edge sensor entrapment protection for the open direction. When an obstruction is sensed during gate opening the gate will reverse for 4 seconds then stop.

This input will be disregarded during gate closing.

Close Photoelectric Sensors

Close Edge

Open Photoelectric Sensors OR Open Edge

INSTALLATION

STEP 10

POWER WIRING

SOLAR APPLICATIONS: For solar applications refer to Solar Panels section in the Appendix, pages 42-46. Follow the directions according to your application.

NOTE: All power wiring should be on a dedicated circuit, calculated using

NEC guidelines. Local codes and conditions must be reviewed for suitability of wire installation.

1. Turn off the AC power from the main power source circuit breaker.

2. Run the AC power wires to the control box.

3. Remove the junction box cover.

4. Connect the green wire to the earth ground rod wire using a wire nut.

5. Connect the white wire to NEUTRAL using a wire nut.

6. Connect the black wire to HOT using a wire nut.

7. Replace the junction box cover. Ensure the wires are not pinched.

8. Plug the J15 plug into the control board. The control board will power up. NOTE: You may see a small spark when plugging the J15 plug into the board.

9. Turn ON AC power to the operator.

OPERATOR POWER SOURCE

DIRECT PLUG-IN TRANSFORMER (120 VAC)

Wire Gauge 14 350 feet (107 m)

Wire Gauge 12

Wire Gauge 10

525 feet (160 m)

850 feet (259 m)

EXTERNAL PLUG-IN TRANSFORMER (24 VAC)

Wire Gauge 18 150 feet (46 m)

Wire Gauge 16

Wire Gauge 14

Wire Gauge 12

Wire Gauge 10

250 feet (76 m)

400 feet (122 m)

600 feet (183 m)

1,000 feet (305 m)

NOTE: Use copper conductors ONLY.

STANDARD CONTROL BOX

J15 Plug

Junction Box Cover

EXTERNAL PLUG-IN TRANSFORMER

Control Box

Transformer

INSTALLATION

STEP 11

FINISH INSTALL

1. Turn the release lever clockwise 180° back to the engaged position.

This engages the motor. The illustration shows the release lever in the engaged position.

2. Turn the key clockwise 180°. This locks the release lever. The operator is now engaged.

3. Fasten warning signs to the gate with cable ties. Warning signs

MUST be installed on both sides of the gate and in plain view.

Release Lever

Key

LIMIT AND FORCE ADJUSTMENT

ADJUSTMENT

To reduce the risk of SEVERE INJURY or DEATH:

• Without a properly installed safety reversal system, persons

(particularly small children) could be SERIOUSLY INJURED or

KILLED by a moving gate.

• Too much force on gate will interfere with proper operation of safety reversal system.

• NEVER increase force beyond minimum amount required to move gate.

• NEVER use force adjustments to compensate for a binding or sticking gate.

• If one control (force or travel limits) is adjusted, the other control may also need adjustment.

• After ANY adjustments are made, the safety reversal system MUST be tested. Gate MUST reverse on contact with a rigid object.

INTRODUCTION

Your operator is designed with electronic controls to make travel limit and force adjustments easy. The adjustments allow you to program where the gate will stop in the open and close position. The electronic controls sense the amount of force required to open and close the gate. The force is adjusted automatically when you program the limits but should be fine tuned using the REVERSAL FORCE dial on the control board (refer to Fine Tune the Force section) to compensate for environmental changes.

The limits can be set using the control board (following page) or a remote control (refer to Limit Setup with a Remote Control in the Appendix).

Setting the limits with a remote control requires a 3-button remote control programmed to OPEN, CLOSE, and STOP.

NOTE: The Test Buttons on the control board will not work until the limits have been set.

ADJUSTMENT

LIMIT AND FORCE ADJUSTMENT continued...

For dual gate applications the limits will have to be set for each operator. The gate MUST be attached to the operator before setting the limits and force.

INITIAL LIMITS AND FORCE ADJUSTMENT

If a mistake is made while programming the limits press the reset button to start over.

1. Set the GATE switch to the 1 position.

2. Press and release the SET OPEN and SET CLOSE buttons simultaneously to enter limit setting mode.

3. Press and hold the MOVE GATE buttons to move the gate to the open or close limit.

4. Press and release the SET CLOSE or SET OPEN button depending on which limit is being set.

5. Press and hold the MOVE GATE button to move the gate to the other limit.

6. Press and release the SET CLOSE or SET OPEN button depending on which limit is being set. The operator will exit limit setting mode.*

7. Cycle the gate open and close using the TEST BUTTONS. This automatically sets the force.

8. For dual gates set the Gate switch to the 2 position and repeat steps

2-7.

When limits are set properly the operator will automatically exit limit setting mode.

* Dual Gates ONLY: When the limits are set on the secondary gate first the control board will not exit the limit setting mode until the limits are set on the primary gate.

CLOSE Limit

RELEASE

TO BEGIN

LIMIT

SETUP

GATE

OFF

TIMER

TO CLOS

(SECONDS)

SET OPEN SET CLOSE

OFF

RELEASE

TO BEGIN

LIMIT

SETUP

MOVE

GATE

OPEN Limit

SET OPEN SET CLOSE

PRESS &

RELEASE

TO BEGIN

LIMIT

SETUP

MOVE

GATE

(SE

RELEASE

TO BEGIN

LIMIT

SETUP

GATE

SET OPEN SET CLOSE

RELEASE

TO BEGIN

LIMIT

SETUP

PRESS &

TO BEGIN

LIMIT

SETUP

(SE

GATE

SET OPEN

LED

LIMIT SETUP LEDS

SET CLOSE

LED

OPERATOR MODE EXPLANATION

OFF OFF NORMAL MODE Limits are set.

BLINKING BLINKING LIMIT SETTING MODE Limits are not set.

BLINKING ON LIMIT SETTING MODE Open limit is not set.

BLINKING LIMIT SETTING MODE Close limit is not set.

ON LIMIT SETTING MODE Limits are set.

ADJUSTMENT

LIMIT AND FORCE ADJUSTMENT continued...

FINE TUNE THE FORCE

The REVERSAL FORCE DIAL on the control board is used for fine tuning the force in cases where wind or environmental changes may affect the gate travel.

Based on the length and weight of the gate it may be necessary to make additional force adjustments. The force setting should be high enough that the gate will not reverse by itself nor cause nuisance interruptions, but low enough to prevent serious injury to a person. The force setting is the same for both the open and close gate directions.

1. Open and close the gate with the test buttons.

2. If the gate stops or reverses before reaching the fully open or closed position, increase the force by turning the force control slightly clockwise.

3. Perform the “Obstruction Test” after every force setting adjustment

(see below).

XMITTER

NETWORK

RSAL

RCE

TEST

BUTTONS

NETWORK

REVERSAL

FORCE

180 MIN

BATT LOW

MAX

ACC PWR OVLD

DIAG

ADJUST THE LIMITS

After both limits are set and the operator is ready to run, one limit can be adjusted independently from the other by following steps 1-3 of the Initial

Limit and Force Adjustment section, on page 23.

SET OPEN SET CLOSE

PRESS &

RELEASE

OBSTRUCTION TEST

The operator is equipped with an automatic obstruction sensing feature.

If the gate encounters an obstruction during motion, the operator will automatically reverse direction of the gate for a short time and then stop the gate. After any adjustments are made, test the operator:

1. Open and close the gate with the test buttons, ensuring that the gate is stopping at the proper open and close limit positions.

2. Place a solid object between the open gate and a rigid structure.

Ensure that the gate, the solid object, and the rigid structure can withstand the forces generated during this obstruction test.

3. Run the gate in the close direction. The gate should stop and reverse upon contact with the solid object. If the gate does not reverse off the solid object, reduce the force setting by turning the force control slightly counter-clockwise. The gate should have enough force to reach both the open and close limits, but MUST reverse after contact with a solid object.

4. Repeat the test for the open direction.

XMITTER

NETWORK

RSAL

RCE

TEST

BUTTONS

CLOSE Limit

OPEN Limit

PROGRAMMING

REMOTE CONTROLS (NOT PROVIDED)

A total of 50 Security✚ 2.0™ remote controls and 2 keyless entries (1

PIN for each keyless entry) can be programmed to the operator. When programming a third keyless entry to the operator, the first keyless entry will be erased to allow the third keyless entry to be programmed. When the operator’s memory is full it will exit the programming mode and the remote control will not be programmed. The memory will need to be erased before programming any additional remote controls.

NOTE: If installing an 86LM to extend the range of the remote controls DO NOT straighten the antenna.

There are 3 different options for programming the remote control depending on how you would like the remote control to function.

Choose a programming option:

LEARN T

BUT

XMITTER

NETWORK

REVERSAL

FORCE

XMITTER

NETWORK

RSAL

RCE

TEST

BUTTONS

OPTION

Single button as OPEN only

Single button (SBC) as

OPEN, CLOSE, and

STOP

Three separate buttons as OPEN, CLOSE, and

STOP

DESCRIPTION

Program a single button on the remote control for open only. The

Timer-to-Close can be set to close the gate.

PROGRAMMING STEPS

1. Press and release the LEARN button (operator will beep and green XMITTER

LED will light).

Program one remote control button as an open, close, and stop.

3. Press the remote control button that you would like to program.

1. Press and release the LEARN button (operator will beep and green XMITTER

LED will light).

Program each remote control button as an open, close, and stop.

2. Press the remote control button that you would like to program.

1. Press and release the LEARN button (operator will beep and green XMITTER

LED will light).

2. Press the OPEN, CLOSE, or STOP button, depending on the desired function.

3. Press the remote control button that you would like to program.

The operator will automatically exit learn mode (operator will beep and green XMITTER LED will go out) if programming is successful. To program additional Security✚ 2.0™ remote controls or remote control buttons, repeat the programming steps above.

NOTICE: To comply with FCC and/or Industry Canada (IC) rules, adjustment or modifications of this transceiver are prohibited. THERE ARE NO USER SERVICEABLE PARTS. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules and IC RSS-210. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

PROGRAMMING

LIFTMASTER INTERNET GATEWAY

(NOT PROVIDED)

USING THE RESET BUTTON ON THE OPERATOR

1. Connect the ethernet cable to the LiftMaster Internet Gateway and the router.

2. Connect power to the LiftMaster Internet Gateway.

3. Create an online account by visiting www.myliftmaster.com.

4. Register the LiftMaster Internet Gateway.

5. Use an internet enabled computer or smartphone to add devices. The

LiftMaster Internet Gateway will stay in learn mode for three minutes.

6. Ensure gate is closed.

7. Give the operator an OPEN command.

8. Within 30 seconds, when the gate is at the open limit press and release the reset button 3 times (on primary gate) to put primary operator into High Band Learn Mode (the operator will beep as it enters learn mode). The LiftMaster Internet Gateway will pair to the operator if it is within range and the operator will beep if programming is successful.

The status as shown by the LiftMaster Internet Gateway app will be either

“open” or “closed”. The gate operator can then be controlled through the

LiftMaster Internet Gateway app.

ERASE ALL CODES

To program the operator to the LiftMaster Internet Gateway:

USING THE LEARN BUTTON ON THE OPERATOR’S

CONTROL BOARD

1. Connect the ethernet cable to the LiftMaster Internet Gateway and the router.

2. Connect power to the LiftMaster Internet Gateway.

3. Create an online account by visiting www.myliftmaster.com.

4. Register the LiftMaster Internet Gateway.

5. Use an internet enabled computer or smartphone to add devices. The

LiftMaster Internet Gateway will stay in learn mode for three minutes.

6. Press the Learn button twice on the primary operator (the operator will beep as it enters learn mode). The LiftMaster Internet Gateway will pair to the operator if it is within range and the operator will beep if programming is successful.

OR

1. Press and release the LEARN button (operator will beep and green

XMITTER LED will light).

2. Press and hold the LEARN button again until the green XMITTER LED flashes and then release the button (approximately 6 seconds). All remote control codes are now erased.

ERASE LIMITS

1. To erase the limits, press and hold the SET OPEN and SET CLOSE buttons simultaneously (5 seconds) until both the SET OPEN and

SET CLOSE LEDs blink rapidly and the operator beeps.

2. Release the buttons and the SET OPEN and SET CLOSE LEDs will blink slowly indicating the limits will need to be set.

TO REMOVE AND ERASE MONITORED

ENTRAPMENT PROTECTION DEVICES

1. Remove the entrapment protection device wires from the terminal block.

2. Press and release the SET OPEN and SET CLOSE buttons simultaneously. The SET OPEN and SET CLOSE LEDs will turn on

(entering learn limit mode).

3. Press and release both SET OPEN and SET CLOSE buttons again to turn off the SET OPEN and SET CLOSE LEDs (exiting learn limit mode).

OPERATION

CONTROL BOARD OVERVIEW

1 SET OPEN Button: The SET OPEN button sets the OPEN limit. See Adjust Limits section.

2 SET CLOSE Button: The SET CLOSE button sets the CLOSE limit. See Adjust Limits section.

3 MOVE GATE Buttons: The MOVE GATE buttons will either open or close the gate when the operator is in Limit setting mode. See Adjust Limits section.

• When AC power is OFF and battery voltage is critically low the gate will latch at a limit until AC power is restored or batteries voltage increases.

• Option select switch set to OPEN forces gate to automatically open and then latch at the OPEN limit until AC power is restored or battery voltage increases.

• Option select switch set to CLOSE forces gate to latch at CLOSE limit if at CLOSE limit or on next CLOSE command until AC power restored or battery voltage increases.

• Constant pressure on a hard command input overrides to open or close the gate.

• Critically low battery is less than 23 V

5 BIPART DELAY Switch: The LOCK/BIPART DELAY switch is used only for dual gates. See Bipart Delay section.

set to OFF. If the TTC is set to the OFF position, then the gate will remain open until the operator receives another command from a control. Rotate the

TIMER-TO-CLOSE dial to the desired setting. The range is 0 to 180 seconds, 0 seconds is OFF.

NOTE: Any radio command, single button control, or CLOSE command on the control board prior to the TTC expiring will close the gate. The TTC is reset by any signals from the open controls, loops, close edges, and close photoelectric sensors (IR’s).

8 REVERSAL FORCE dial: The REVERSAL FORCE dial adjusts the force. See Force Adjustment section.

11 Error Code Display: The error code display will show the operator type, firmware version, and error codes. The operator type will display as "LA" followed by a "40" which indicates the operator type as LA400DC. The firmware version will show after the operator type, example "1.2".

1 2 4 5 6 9

OPERATION

MANUAL RELEASE

In case of a power failure, the operator can be disengaged from the gate.

With an operator, the release action may sometimes feel stiff/jerky, which is normal and has no effect on function. NOTE: It is normal for the operator to run slow right after a disconnect or complete loss of AC/ battery power (the operator will need to run a complete open and close cycle).

RELEASE

1. Insert the key into the lock.

2. Turn the key counter-clockwise 180°.

3. Turn the release lever counter-clockwise 180°.

Operator is in manual mode and the gate can be opened and closed manually.

ENGAGE

1. Turn the release lever clockwise 180°. This engages the motor.

2. Turn the key clockwise 180°. This locks the release lever.

3. Remove the key and store in a safe place. The operator is now engaged.

RESET BUTTON

The reset button is located on the side of the control box and serves several functions:

• Press the reset button to stop a moving gate during a normal open/ close cycle, like a stop button.

• Press the reset button once while the gate is in open position to disable the Timer-to-Close. The gate will stay in the open position. To restart the Timer-to-Close either press the reset button or activate the gate with a programmed remote control.

• Press the reset button to shut off the alarm and reset the operator.

PARTY MODE

Press the reset button once while the gate is in open position to disable the Timer-to-Close. The gate will stay in the open position. To restart the

Timer-to-Close either press the reset button or activate the gate with a programmed remote control.

Reset Button

OPERATION

OPERATOR ALARM

If a contact sensor detects an obstruction twice consecutively the alarm will sound (up to 5 minutes) and the operator will need to be reset.

When the inherent force of the operator (RPM/current sensor) detects the following (twice consecutively) the alarm will sound (up to 5 minutes) and the operator will need to be reset:

A. The operator arm or gate is incorrectly installed.

B. The gate does not meet specifications.

C. Gate hinges are too tight or broken and the gate is not moving freely.

D. The gate is moving and a car pushes the gate.

E. A foreign object is on the gate frame while the gate is moving.

F. The gate hits the driveway, curb or other, and gets stuck or bent in an awkward position.

Remove any obstructions. Press the reset button to shut off the alarm and reset the operator. After the operator is reset, normal functions will resume.

The operator alarm will beep 3 times with a command if the battery is low.

REMOTE CONTROL

SINGLE BUTTON CONTROL (SBC) FUNCTIONALITY

Once the remote control has been programmed the operator will operate as follows:

When gate is in the closed position, activation of the remote control button will open the gate. During the open cycle another activation of the remote control will stop the gate and the next activation of the remote control will close the gate.

When the gate is in the open position, activation of the remote control button will close the gate. If the remote control is activated while the gate is closing, the gate will stop and the next activation will open the gate.

ACCESSORY WIRING

EXTERNAL CONTROL DEVICES

EXIT

(2 Terminals)

This input is a soft open command (maintained switch does not override external safeties and does not reset alarm condition). Used for exit probe, telephone entry, external exit loop detector, or any device that would command the gate to open.

• Opens a closing gate and holds open an open gate, if maintained, pauses Timer-to-Close at OPEN limit.

SHADOW

(2 Terminals)

This input is used for external shadow loop detector when loop is positioned under the swing of the gate.

• Holds open gate at open limit

• Only active when the gate is at the OPEN limit, disregarded at all other times

• Pauses Timer-to-Close at OPEN limit

INTERRUPT

(2 Terminals)

This input is used for photoelectric sensors and external interrupt loop detector when loop is on the outside of the gate.

• Holds open gate at open limit

• Stops and reverses a closing gate to open limit

• Pauses Timer-to-Close at OPEN limit, activates quick close and anti-tailgate features when enabled on the expansion board

(control board)

Exit

Com

Shadow

Com

Interrupt

Com

Exit Loop

Interrupt Loop

Shadow Loop

VEHICLE DETECTION DEVICES

The same accessory inputs used for vehicle detection devices are also used for entrapment protection devices (refer to step 9 of Installation).

The vehicle detection devices may be monitored or non-monitored, but only ONE monitored device may be connected to each input, inclusive of entrapment protection devices. Multiple non-monitored devices can be wired to the same input. A monitored device sends a pulsed signal to the operator so the operator is aware of the device. If the operator does not receive the signal from the device indicating it is working properly, it will not run in that direction.

CLOSE EYES/INTERRUPT

(2 Terminals)

The CLOSE EYES/INTERRUPT input is for photoelectric sensor vehicle detection for the close direction. When an obstruction is sensed during gate closing the gate will open to the full open position. This input will be disregarded during gate opening and resets the Timer-to-Close.

CLOSE EDGE

(2 Terminals)

The CLOSE EDGE input is for edge sensor vehicle detection for the close direction. When an obstruction is sensed during gate closing the gate will reverse for 4 seconds then stop, disengaging the Timer-to-Close. This input will be disregarded during gate opening.

OPEN EYES/EDGE

(2 Terminals)

The OPEN EYES/EDGE input is for photoelectric sensor or edge sensor vehicle detection for the open direction. When an obstruction is sensed during gate opening the gate will reverse for 4 seconds then stop. This input will be disregarded during gate closing.

Close Photoelectric Sensors

Close Edge

Open Photoelectric Sensors OR Open Edge

ACCESSORY WIRING

LOCKS

MAGLOCK

(2 Terminals, N.C. and COM)

Relay contact output, Normally - closed (N.C.) output for maglocks.

Relay activates prior to motor activation and during motor run. Relay is off when motor is off.

NOTE: For AC power install a Siemens S10K30 MOV (Metal Oxide

Varistor) or equivalent. For DC power install a 1N4005 diode or equivalent.

(control board)

SOLENOID

(2 Terminals, N.O. and COM)

Normally - open (N.O.) output for solenoid locks

Relay activates prior to motor activation and during motor run. Relay is off when motor is off.

NOTE: For AC power install a Siemens S10K30 MOV (Metal Oxide

Varistor) or equivalent. For DC power install a 1N4005 diode or equivalent.

Maglock

(control board)

1N4005 diode or equivalent.

Siemens S10K30 MOV

(Metal Oxide Varistor) or equivalent.

Solenoid Lock

(not provided)

1N4005 diode or equivalent.

(not provided)

MISCELLANEOUS WIRING

SINGLE BUTTON CONTROL (SBC)

(2 Terminals)

Gate command sequence - Open, Stop, Close, Stop,...

Soft open (maintained switch does not override external safeties and does not reset alarm condition).

FIRE DEPARTMENT OPEN INPUT

(2 Terminals)

Acts as hard open.

Maintained input overrides (ignores) external safeties (photoelectric sensor and edge), pauses Timer-to-Close momentary input logic as single button control and safeties remain active, re-enables Timer-to-Close.

(main control board)

Single Button Control Station

SBC

Com

Fire Dept

Com

Fire Department

ACCESSORY POWER 24 VDC, MAX 500 mA

(4 Terminals)

• SWITCHED: Switched ON with gate motion (stays on 5 seconds after motion).

• UNSWITCHED: 24 Vdc voltage out to power accessories, always ON.

(main control board)

Accessory Power Switched

Com (-)

Acc Power +24 Vdc

Com (-)

Acc Power +24 Vdc

Accessory Power Unswitched

MAINTENANCE

IMPORTANT SAFETY INFORMATION

To reduce the risk of SEVERE INJURY or DEATH:

• READ AND FOLLOW ALL INSTRUCTIONS.

• ANY maintenance to the operator or in the area near the operator

• Disconnect power at the fuse box BEFORE proceeding. Operator

MUST be properly grounded and connected in accordance with national and local electrical codes. NOTE: The operator should be on a separate fused line of adequate capacity.

• NEVER let children operate or play with gate controls. Keep the remote control away from children.

• ALWAYS keep people and objects away from the gate. NO ONE

SHOULD CROSS THE PATH OF THE MOVING GATE.

• The entrance is for vehicles ONLY. Pedestrians MUST use separate entrance.

• Use the manual disconnect release ONLY when the gate is not moving.

• KEEP GATES PROPERLY MAINTAINED. Read the owner’s manual.

Have a qualified service person make repairs to gate hardware.

• ALL maintenance MUST be performed by a LiftMaster professional.

• Activate gate ONLY when it can be seen clearly, is properly adjusted and there are no obstructions to gate travel.

• To reduce the risk of FIRE or INJURY to persons use ONLY

LiftMaster part 29-NP712 for replacement batteries.

• SAVE THESE INSTRUCTIONS.

• ALWAYS wear protective gloves and eye protection when changing the battery or working around the battery compartment.

MAINTENANCE CHART

Disconnect all power (AC and battery) to the operator before servicing. The operator's AC Power switch ONLY turns off AC power to the control board and DOES NOT turn off battery power. ALWAYS disconnect the batteries to service the operator.

DESCRIPTION

Entrapment Protection Devices

Warning Signs

Manual Release

Gate

Accessories

Electrical

Mounting Hardware

Operator

Batteries

TASK

Check and test for proper operation

Make sure they are present

Check and test for proper operation

Inspect for wear or damage

Check all for proper operation

Inspect all wire connections

Check for tightness

Inspect for wear or damage

Replace

MONTH

CHECK AT LEAST ONCE EVERY

6 MONTHS 3 YEARS

NOTES:

• Severe or high cycle usage will require more frequent maintenance checks.

• It is suggested that while at the site voltage readings be taken at the operator. Using a digital voltmeter, verify that the incoming voltage to the operator is within ten percent of the operator’s rating.

BATTERIES

Batteries will degrade over time depending on temperature and usage.

The operator alarm will beep 3 times with a command if the battery is low. Batteries do not perform well in extremely cold temperatures. For best performance, the batteries should be replaced every 3 years. Use only LiftMaster part 29-NP712 for replacement batteries. The standard control box comes with two 7AH batteries.

TROUBLESHOOTING

To protect against fire and electrocution:

• DISCONNECT power (AC or solar and battery) BEFORE installing or servicing operator.

For continued protection against fire:

• Replace ONLY with fuse of same type and rating.

ERROR CODES

NOTE: When cycling or disconnecting power (ac/dc) to the control board, it is recommended that you unplug the J15 plug.

TO VIEW THE ERROR CODES

The error codes are shown on the error code display.

...then press and hold the

OPEN button until “Er” shows ...then press and hold the

CLOSE button...

Press and hold the

STOP button...

The operator will show the error sequence number followed by the error code number:

ERROR SEQUENCE NUMBER

The first number shown is the most recent error (example: "01" shown below). The display will show the sequence of errors that occurred starting with "01" and going up to error

"20".

A SECOND

LATER....

ERROR CODE NUMBER

The second number shown after the error sequence number is the error code itself (31-99, example" "31" shown below). Refer to the chart on the following page for an explanation of each error code.

ERROR CODE DISPLAY

OPEN, CLOSE, & STOP BUTTONS

TO SCROLL THROUGH THE SAVED ERROR CODES

TO EXIT ERROR CODE DISPLAY

Press and release the STOP button to exit. The error code display will also time out after two minutes of inactivity.

Press the OPEN button to cycle to the most recent errors ("01").

Press the CLOSE button to cycle to the oldest error (up to "20").

The operator will only keep track of up to 20 errors, then will start saving over the oldest errors as new errors occur.

TO RESET THE ERROR CODE HISTORY

1. Press and hold the STOP button for six seconds. The display will show "Er" then "CL" alternately for six seconds.

2. Release the STOP button. The error history has now been reset and the display will show "- -" until a new error occurs.

3. Press and release the STOP button to exit.

TROUBLESHOOTING

ERROR CODES continued...

Some errors are saved in the error code history and some are not. If an error is not saved it will briefly appear on the error code display as it occurs, then disappear.

Code Error Meaning

Solution

Control board has experienced an internal failure.

Disconnect all power, wait 15 seconds, then reconnect power (reboot).

If issue continues, replace control board.

Linear Drive Disengaged (Arm 1) Disengage then re-engage arm, check wiring and connections.

Linear Drive Disengaged (Arm 2)

Absolute Position Encoder Error, not getting position information from encoder

Disengage then re-engage arm, check wiring and connections.

Check the operator cable connections, then reprogram the limits.

Max-Run-Time Exceeded Error

Product ID Error

Product ID Failure

Check for an obstruction, then reprogram the limits.

Was the control board just replaced? If so, erase limits, enter limit setup mode and set limits. If not, disconnect all power, wait 15 seconds, then reconnect power before changing product ID harness.

Unplug product ID harness then plug back in. Disconnect all power, wait 15 seconds, then reconnect power before replacing product ID harness.

Hard Stop Limit (Arm 1)

Hard Stop Limit (Arm 2)

Battery overvoltage

Battery overcurrent

No battery at boot up

Loop Error - Failure or missing exit loop (SHORT or OPEN - LiftMaster Plug-in Loop Detector only)

Loop Error - Failure or missing shadow loop

(SHORT or OPEN - LiftMaster Plug-in Loop

Detector only)

Loop Error - Failure or missing interrupt loop

(SHORT or OPEN - LiftMaster Plug-in Loop

Detector only)

Wireless edge battery low

Pass-point not detected (Arm 1)

Limit may be set too tightly against a non-resilient hard stop (re-adjust limit). Operator may be at end of travel (re-adjust mounting).

Too much voltage on the battery. Check harness. Make sure you do

NOT have a 24V battery on a 12V system.

Possible short of the battery charge harness. Check harness. Make sure you do NOT have a 12V battery on a 24V system.

Check battery connections and installation. Replace batteries if depleted to less than 20V on a 24V system. Make sure you do NOT have a single 12V battery on a 24V system.

Check loop wiring throughout connection. May be a short in the loop, or an open connection in the loop.

Pass-point not detected (Arm 2)

Brownout occurred

Wireless Second Operator Communication Error

Replace batteries in wireless edge.

Check yellow pass-point wiring. If limits are not accurate, reprogram.

Rarely, may be standard operation.

Check yellow pass-point wiring. If limits are not accurate, reprogram.

Rarely, may be standard operation.

AC/DC board supply dipped below allowable level. Review power supply and wiring. If rebooting, ensure enough time for discharge of power to force a fresh boot.

Check the second operator for power. If OFF, restore power and try to run the system. If powered, deactivate the wireless feature and then re-learn the second operator.

Review monitored entrapment protection device connections.

Minimum number of monitored entrapment protection devices (one) not installed.

CLOSE EYE/INTERRUPT held more than 3 minutes

(main board)

CLOSE EDGE held more than 3 minutes (main board)

OPEN EYE/EDGE held more than 3 minutes (main board)

Check CLOSE EYE/INTERRUPT input on main board; check for alignment or obstruction.

Check CLOSE EDGE input on main board; check for alignment or obstruction.

Check OPEN EYE/EDGE input on main board; check for alignment or obstruction.

Saved

YES

TROUBLESHOOTING

ERROR CODES continued...

Some errors are saved in the error code history and some are not. If an error is not saved it will briefly appear on the error code display as it occurs, then disappear.

Code Error Meaning

Wireless edge triggered more than 3 minutes

Wireless edge loss of monitoring

Wireless edge triggered

CLOSE EYE/INTERRUPT triggered, causing reversal, preventing close, or resetting TTC (main board)

CLOSE EDGE triggered, causing reversal, preventing close, or cancelling TTC (main board)

OPEN EYE/EDGE triggered, causing reversal or preventing opening (main board)

CLOSE EYE/INTERRUPT triggered, causing reversal, preventing close, or resetting TTC

(expansion board)

Close input (EYE/EDGE) communication fault

(secondary control box)

Open input (EYE/EDGE) communication fault

(secondary control box)

Force reversal (Arm 1)

Force reversal (Arm 2)

RPM / STALL Reversal (Arm 1)

RPM / STALL Reversal (Arm 2)

Normal Operation

Solution

Check wired input for wiring issue or obstruction.

Check wireless edge inputs.

IF an obstruction occurred, no action required. If an obstruction did

NOT occur, check inputs and wiring.

IF an obstruction occurred, no action required. If an obstruction did

NOT occur, check alignment, inputs, and wiring.

IF an obstruction occurred, no action required. If an obstruction did

NOT occur, check alignment, inputs, and wiring.

IF an obstruction occurred, no action required. If an obstruction did

NOT occur, check alignment, inputs, and wiring.

IF an obstruction occurred, no action required. If an obstruction did

NOT occur, check alignment, inputs, and wiring.

Check the connections between the main board and the secondary operator

Check the connections between the main board and the secondary operator.

Check for obstruction. If no obstruction, check that the operator arm is engaged and free to move. Refer to Limit and Force Adjustment section, and Obstruction Test.

Check for obstruction. If no obstruction, check the operator cable wiring and that the operator arm is engaged and free to move. Replace the operator arm if necessary.

No action required

Saved

YES

TROUBLESHOOTING

CONTROL BOARD LEDS

INPUT

POWER

OFF

STATUS LEDS

BATT

CHARGING

TIMER

GATE

MOVING

OFF

MEDIUM BLINK (1 blink per second)

FAST BLINK (2 blinks per second)

FASTEST BLINK (8 blinks per second)

OFF

MEDIUM BLINK (1 blink per second)

FASTEST BLINK (8 blinks per second)

BATT LOW OFF

ACC PWR

OVLD

BLINK (1 blink per second)

OFF

OFF state

AC charger or Solar power available

Not charging

Three stage battery charging

The timer is disabled

The timer is enabled

The timer is running

The timer is paused

The timer is cancelled

The gate is stopped

The gate is opening or closing

Operator is in E1 (single entrapment)

The operator is in E2 (double entrapment)

No battery error

Battery low

Battery critically low

OFF state

Accessory overload protector opened

SBC INPUT

FIRE DEPT

INPUT

EXIT

SHADOW

CLOSE EYES/

INTERRUPT

CLOSE EDGE

OPEN EYES/

EDGE

LOCK

BLINK

OFF

BLINK

OFF

BLINK

OFF

BLINK

OFF

BLINK

OFF

BLINK

OFF

BLINK

OFF

INPUT LEDS

Input inactive

Input active

Input active on other operator

Input inactive

Input active

Input active on other operator

Input inactive

Input active

Input active on other operator

Input inactive

Input active

Input active on other operator

Input inactive

Input active

Input active on other operator

Input inactive

Input active

Input active on other operator

Input inactive

Input active

Input active on other operator

Input inactive

Input active

BLINK Input active on other operator

STATUS LEDS INPUT LEDS

TROUBLESHOOTING

TROUBLESHOOTING CHART

SYMPTOM

Operator does not run and error code display not on.

Control board powers up, but motor does not run.

Arm moves, but cannot set correct limits.

POSSIBLE CAUSES

a) No power to control board b) Open fuse c) If on battery power only, low or dead batteries d) Defective control board a) Reset button is stuck b) Stop button active or jumper not in place for stop circuit c) If on battery power only, low or dead batteries d) Open or Close input active e) Entrapment Protection Device active f) Vehicle loop detector or probe active g) Defective control board a) Arm does not extend or retract enough during travel b) Arm is interfering with mounting bracket c) Gate is too difficult to move

Gate does not fully open or fully close when setting limits.

a) Arm does not extend or retract enough during travel b) Arm is interfering with mounting bracket c) Gate is too difficult to move

Operator does not respond to a wired control/command

(example: Open,

Close, SBC, etc.)

Operator does not respond to a wireless control or transmitter a) Check Open and Close command input LEDs b) Stop button is active c) Reset button is stuck d) If on battery power only, low or dead batteries e) Entrapment Protection Device active f) Vehicle loop detector or vehicle probe active a) Check XMITTER LED when wireless control is active b) Stop button is active c) Reset button is stuck d) Poor radio reception

Gate stops during travel and reverses immediately.

a) Control (Open, Close) becoming active b) Vehicle loop detector active c) Low battery voltage

SOLUTIONS

a) Check AC and battery power b) Check fuses c) Charge batteries by AC or solar power or replace batteries d) Replace defective control board a) Check Reset button b) Check Stop button is not “stuck on”, or verify that the stop button is a normally closed circuit, or put a jumper on the stop circuit. c) Charges batteries by AC or solar power or replace batteries d) Check all Open and Close inputs for a “stuck on” input e) Check all Entrapment Protection Device inputs for a “stuck on” sensor f) Check all vehicle detector inputs for a “stuck on” detector g) Replace defective control board a) Disengage the arm and ensure arm moves freely b) Examine the hinge point where the arm mounts to the gate post. Make sure that the arm housing does not hit or interfere with the gate post or mounting bracket. Correct as necessary.

c) Disconnect arm from gate and move gate manually. Gate must move easily and freely through its entire range, limit-to-limit. Repair gate as needed.

a) Disengage the arm and ensure arm moves freely b) Examine the hinge point where the arm mounts to the gate post. Make sure that the arm housing does not hit or interfere with the gate post or mounting bracket. Correct as necessary.

c) Remove arm from gate and move gate manually. Gate must move easily and freely through its entire range, limit-to-limit. Repair gate as needed.

a) Check all Open and Close inputs for a “stuck on” input b) Check Stop button is not “stuck on” c) Check Reset button d) Charges batteries by AC or solar power or replace batteries e) Check all Entrapment Protection Device inputs for a “stuck on” sensor f) Check all vehicle detector inputs for a “stuck on” detector a) Activate wireless control and check XMITTER LED is on. Re-learn wireless control/transmitter to control board. Replace wireless control as needed.

b) Check Stop button is not “stuck on” c) Check Reset button d) Check if similar wired control operates correctly. Check if wireless controls works properly when within a few feet of operator. Check operator’s antenna and antenna wire. Check other wireless controls or devices.

a) Check all Open and Close inputs for an active input b) Check all vehicle detector inputs for an active detector c) Battery voltage must be 23.0 Vdc or higher. Charge batteries by AC or solar power or replace batteries

Gate opens, but will not close with transmitter or

Timer-to-Close.

a) Open control active b) Vehicle loop detector active c) Loss of AC power with AC FAIL set to

OPEN d) Low battery with LOW BATT set to OPEN e Fire Dept input active f) Timer-to-Close not set g) Close Entrapment Protection Device active a) Check all Open inputs for an active input b) Check all vehicle detector inputs for an active detector c) Check AC power and AC Fail option setting d) Check if AC power is available. If no AC power, then running on batteries and battery voltage must be 23.0 Vdc or higher. Charge batteries by AC or solar power or replace batteries.

e) Check Fire Dept input f) Check Timer-to-Close (TTC) setting g) Check all Entrapment Protection Device inputs for an active sensor

TROUBLESHOOTING

TROUBLESHOOTING CHART continued...

SYMPTOM

Gate closes, but will not open.

POSSIBLE CAUSES

a) Vehicle loop detector active b) Low battery with LOW BATT option set to CLOSE

Exit loop activation does not cause gate to open.

a) Exit vehicle detector setup incorrectly b) Defective Exit loop detector c) Low battery with LOW BATT option set to CLOSE

SOLUTIONS

a) Check all vehicle detector inputs for an active detector b) Check if AC power is available. If no AC power, then running on batteries and battery voltage must be 23.0 Vdc or higher. Charge batteries by AC or solar power or replace batteries a) Review Exit loop detector settings. Adjust settings as needed.

b) Replace defective Exit loop detector.

c) Check if AC power is available. If no AC power, then running on batteries and battery voltage must be 23.0 Vdc or higher. Charge batteries by AC or solar power or replace batteries.

a) Review Interrupt loop detector settings. Adjust settings as needed.

b) Replace defective Interrupt loop detector.

Interrupt loop does not cause gate to stop and reverse.

Shadow loop does not keep gate at open limit.

a) Vehicle detector setup incorrectly b) Defective vehicle loop detector a) Vehicle detector setup incorrectly b) Defective vehicle loop detector

Obstruction in gate's path does not cause gate to stop and reverse a) Force adjustment needed

Photoelectric sensor does not stop or reverse gate.

a) Incorrect photoelectric sensor wiring b) Defective photoelectric sensor

Edge Sensor does not stop or reverse gate.

a) Incorrect edge sensor wiring b) Defective edge sensor a) Review Shadow loop detector settings. Adjust settings as needed.

b) Replace defective Shadow loop detector.

a) Refer to the Adjustment section to conduct the obstruction test and perform the proper force adjustment that is needed.

a) Check photoelectric sensor wiring. Retest that obstructing photoelectric sensor causes moving gate to stop, and may reverse direction.

b) Replace defective photoelectric sensor. Retest that obstructing photoelectric sensor causes moving gate to stop, and may reverse direction.

a) Check edge sensor wiring. Retest that activating edge sensor causes moving gate to stop and reverse direction.

b) Replace defective edge sensor. Retest that activating edge sensor causes moving gate to stop and reverse direction.

a) Check for cause of entrapment (obstruction) detection and correct. Press the reset button to shut off alarm and reset the operator.

Alarm sounds for 5 minutes or alarm sounds with a command.

Alarm beeps three times with a command.

a) Double entrapment occurred (two obstructions within a single activation) a) Low battery a) Check if AC power is available. If no AC power, then running on batteries and battery voltage must be 23.0 Vdc or higher. Charge batteries by AC or solar power or replace batteries

On dual-gate system, incorrect gate opens first or closes first.

Alarm beeps when running.

a) Incorrect Bipart switch setting a) Expansion board setting b) Constant pressure to open or close is given

Expansion board function not controlling gate.

a) Defective main board to expansion board wiring b) Incorrect input wiring to expansion board c) Defective expansion board or defective main board a) Change setting of both operator’s Bipart switch settings. One operator should have Bipart switch ON (operator that opens second) and the other operator should have Bipart switch OFF (operator that opens first) a) Pre-warning is set to "ON" b) Constant pressure to open or closed is given a) Check main board to expansion board wiring. If required, replace wire cable.

b) Check wiring to all inputs on expansion board. c) Replace defective expansion board or defective main board

TROUBLESHOOTING

TROUBLESHOOTING CHART continued...

SYMPTOM

Maglock not working correctly.

POSSIBLE CAUSES

a) Maglock wired incorrectly

Solenoid lock not working correctly.

a) Solenoid wired incorrectly

SOLUTIONS

a) Check that Maglock is wired to N.C. and COM terminals. Check that

Maglock has power (do not power maglock from control board accessory power terminals). If shorting lock’s NO and COM wires does not activate Maglock, then replace Maglock or Maglock wiring

(refer to Wiring Diagrams). a) Check that Solenoid is wired to N.O. and COM terminals. Check that

Solenoid has power (do not power solenoid from control board accessory power terminals). If shorting lock’s NC and COM wires does not activate Solenoid, then replace Solenoid lock or Solenoid wiring (refer to Wiring Diagrams).

a) Learn the limits a) Move accessory to accessory power "ON"

Switched (SW) Accessory power remaining on.

a) In limit setup mode

Accessories connected to

Switch (SW) Accessory power not working correctly, turning off, or resetting.

a) Normal behavior

Accessories connected to

Accessory power not working correctly, turning off, or resetting.

a) Accessory power protector active b) Defective control board

Quick Close not working correctly.

a) Quick Close setting incorrect b) Interrupt loop detector c) Defective Expansion board

Anti-Tailgating not working correctly.

a) Anti-Tail setting incorrect b) Interrupt loop detector c) Defective Expansion board

AUX Relay not working correctly.

a) AUX Relay setting incorrect b) AUX Relay wiring incorrect c) Defective Expansion board a) Disconnect all accessory powered devices and measure accessory power voltage (should be 23 – 30 Vdc). If voltage is correct, connect accessories one at a time, measuring accessory voltage after every new connection.

b) Replace defective control board a) Check that Quick Close setting is ON b) Check operation of Interrupt Loop detector c) Replace defective Expansion board a) Check that Anti-Tail setting is ON b) Check operation of Interrupt Loop detector c) Replace defective Expansion board a) Check AUX Relay switches settings b) Check that wiring is connected to either N.O. and COM or to N.C. and COM.

c) Set AUX Relay to another setting and test. Replace defective expansion board.

BRACKET TYPES

PULL-TO-OPEN

Left-Hand Gate

APPENDIX

Right-Hand Gate

PUSH-TO-OPEN

Left-Hand Gate Right-Hand Gate

APPENDIX

STEP 10

SOLAR PANEL(S)

SOLAR PANELS ARE NOT PROVIDED. SEE ACCESSORIES.

33AH Battery Requirements:

• Large Metal Control Box for Solar Applications

(Model XLSOLARCONTDC)

• A minimum of two 10W solar panels in series

(Model SOLPNL10W12V)

• A maximum of six 10W solar panels (Model SOLPNL10W12V).

Configuration of three sets of two 10W paralleled panels put in series.

• Two 33AH Batteries (Model A12330SGLPK)

• Solar Battery Harness (Model K94-37236)

7AH Battery Requirements:

• Standard Control Box for Solar Applications (Model LA400CONTDC)

• A minimum of two 10W solar panels in series (Model

SOLPNL10W12V)

• A maximum of six 10W solar panels (Model SOLPNL10W12V).

Configuration of three sets of two 10W paralleled panels put in series.

• Two 7AH batteries (29-NP712)

• Solar Battery Harness (Model K94-37236)

• Battery Tray (Model K10-36183)

Disconnect the expansion board if it is not in use to improve performance. We recommend LiftMaster low power draw accessories to minimize power draw, refer to accessory page. Use the tables below to see performance trade-offs. NOTE: Input solar power is 24 Vdc at 60 watts maximum.

The solar panel(s) must be located in an open area clear of obstructions and shading for the entire day. The gate operator is not supported in northern climates where temperatures reach below -4˚F. This is due to cold weather and a reduced number of hours of sunlight during the winter months. Cycle rate may vary from solar chart for areas that reach below 32˚F. Solar panels should be cleaned on a regular basis for best performance to ensure proper operation.

SOLAR USAGE GUIDE

The LA400DC has best in class solar performance due to highly efficient electronics that draw very little power while the gate is not in use (standby).

Typical System Standby Battery Current Consumption (mA) System Configuration

2.7 mA Main control board draw with no remote controls programmed

+1 mA

+2.4 mA

Low band radio receiver active (one or more wireless transmitters learned)

High band radio active (MyQ device programmed)

+11.1 mA

+3.8 mA

Expansion board

Per loop detector (up to 3 loop detectors can be plugged into the expansion board)

This low current draw drastically increases the number of days the operator can remain in standby. To determine your system’s performance, reference the above table and determine how many milliamps (mA) your system will draw from the batteries.

EXAMPLE 1: A system with only a main control board and one or more hand held remote controls programmed will draw 3.7 mA from the batteries while the system is in standby (2.7 mA + 1 mA = 3.7 mA).

EXAMPLE 2: A system with only a main control board, one or more hand held remote controls programmed, and 20 mA of external accessories connected to the main control board's accessory power output will draw 23.7 mA from the batteries while the system is in standby

(2.7 mA + 1 mA + 20 mA = 23.7 mA).

EXAMPLE 3: A system with a main control board, expansion board, two loop detectors, and one or more hand held remote controls programmed will draw 18 mA from the batteries while the system is in standby (2.7 mA + 11.1 mA + 3.8 mA*2 +1 = 18.6 mA).

Operator performance with no sun or loss of AC power

BATTERY

CURRENT

DRAW (mA)

2.7

3.7

6.1

14.8

SYSTEM CONFIGURATION main control board only remote controls programmed remote controls and MyQ programmed remote controls and expansion board remote controls, expansion board, and one loop detector remote controls, expansion board, and three loop detectors

18.6

26.2

100

200

300

500

All numbers are estimates. Actual results may vary.

DAYS OF STANDBY

7AH batteries

133

33AH batteries

180

105

SINGLE GATE CYCLES ON BATTERY

7AH batteries

400

33AH batteries

3623

3622

3621

3620

3619

3618

3615

3610

3596

3583

3557

DUAL GATE CYCLES ON BATTERY

7AH batteries

330

329

328

326

322

318

311

330

33AH batteries

1752

1751

1750

1749

1746

1740

1734

1721

STEP 10 continued...

SOLAR PANEL(S)

SOLAR USAGE GUIDE

APPENDIX

SOLAR ZONES

NOT AVAILABLE

BATTERY

CURRENT

DRAW (mA)

SOLAR GATE CYCLES PER DAY (SINGLE GATE)

ZONE 1

(6 Hrs sunlight/day)

7AH batteries 33AH batteries

ZONE 2

(4 Hrs Sunlight/day)

7AH batteries 33AH batteries

10W SOLAR PANEL

20W SOLAR PANEL

40W SOLAR PANEL

60W SOLAR PANEL

100

200

100

250

BATTERY

CURRENT

DRAW (mA)

10W SOLAR PANEL

20W SOLAR PANEL

40W SOLAR PANEL

60W SOLAR PANEL

100

200

100

250

All numbers are estimates. Actual results may vary.

100

16 n/a

100

43 n/a

100

47 n/a

100

65 n/a

100

100 n/a

30 n/a

SOLAR GATE CYCLES PER DAY (DUAL GATE) n/a

100

63 n/a

100

ZONE 1

(6 Hrs sunlight/day)

7AH batteries 33AH batteries

ZONE 2

(4 Hrs Sunlight/day)

7AH batteries 33AH batteries

18 n/a

100

13 n/a n/a

20 n/a

28 n/a

100

45 n/a

14 n/a n/a

27 n/a

100

58 n/a

100

ZONE 3

(2 Hrs Sunlight/day)

7AH batteries 33AH batteries n/a

25 n/a n/a

63 n/a n/a

100

83 n/a n/a

18 n/a n/a n/a n/a

33 n/a n/a

100

97 n/a n/a

100

55 n/a

19 n/a n/a n/a

ZONE 3

(2 Hrs Sunlight/day)

7AH batteries 33AH batteries n/a n/a n/a n/a n/a

11 n/a n/a

27 n/a n/a

36 n/a n/a n/a n/a n/a n/a n/a

14 n/a n/a

42 n/a n/a

24 n/a

APPENDIX

LIMIT SETUP WITH A REMOTE CONTROL

To set the limits using a remote control, first you will need a 3-button remote control that has been programmed for OPEN, CLOSE, and STOP. Refer to the Programming section.

INITIAL LIMITS AND FORCE ADJUSTMENT

For dual gate applications the limits will have to be set for each operator. The gate MUST be attached to the operator before setting the limits and force.

Ensure the gate is closed.

1. Press and release the SET OPEN and SET CLOSE buttons simultaneously to enter limit setting mode.

2. Press and hold the OPEN or CLOSE button on the remote control until the gate reaches the desired open position. The gate can be jogged back and forth using the OPEN and CLOSE buttons on the remote control.

3. Once the gate is in the desired open position, press and release the

STOP button on the remote control.

4. Press and release the OPEN button on the remote control again to set the open limit.

5. Press and hold the CLOSE or OPEN button on the remote control until the gate reaches the desired close position. The gate can be jogged back and forth using the OPEN and CLOSE buttons on the remote control.

6. Once the gate is in the desired close position, press and release the

STOP button on the remote control.

7. Press and release the CLOSE button on the remote control again to set the close limit.

8. Cycle the gate open and close. This automatically sets the force.

When limits are set properly the operator will automatically exit limit setting mode.

ADJUST THE LIMITS

If the limits have already been set the operator will exit the limit setting mode after resetting each limit.

Set the Close Limit Only

1. Press and release the SET OPEN and SET CLOSE buttons simultaneously to enter limit setting mode.

2. Press and hold the CLOSE button on the remote control until the gate reaches the desired close position. The gate can be jogged back and forth using the OPEN and CLOSE buttons on the remote control.

3. Once the gate is in the desired close position, press and release the

STOP button on the remote control.

4. Press and release the CLOSE button on the remote control again to set the close limit.

When the close limit is set properly the operator will automatically exit limit setting mode.

Set the Open Limit Only

1. Press and release the SET OPEN and SET CLOSE buttons simultaneously to enter limit setting mode.

2. Press and hold the OPEN button on the remote control until the gate reaches the desired open position. The gate can be jogged back and forth using the OPEN and CLOSE buttons on the remote control.

3. Once the gate is in the desired open position, press and release the

STOP button on the remote control.

4. Press and release the OPEN button on the remote control again to set the open limit.

When the open limit is set properly the operator will automatically exit limit setting mode.

3-Button Remote Control programmed for OPEN, CLOSE, and

STOP

SET OPEN SET CLOSE

PRESS &

RELEASE

APPENDIX

LIMIT SETUP WITH A REMOTE CONTROL

To set the limits using a remote control, first you will need a 3-button remote control that has been programmed for OPEN, CLOSE, and STOP. Refer to the Programming section.

INITIAL LIMITS AND FORCE ADJUSTMENT

For dual gate applications the limits will have to be set for each operator. The gate MUST be attached to the operator before setting the limits and force.

Ensure the gate is closed.

1. Press and release the SET OPEN and SET CLOSE buttons simultaneously to enter limit setting mode.

3. Once the gate is in the desired open position, press and release the

STOP button on the remote control.

4. Press and release the OPEN button on the remote control again to set the open limit.

6. Once the gate is in the desired close position, press and release the

STOP button on the remote control.

7. Press and release the CLOSE button on the remote control again to set the close limit.

8. Cycle the gate open and close. This automatically sets the force.

When limits are set properly the operator will automatically exit limit setting mode.

ADJUST THE LIMITS

If the limits have already been set the operator will exit the limit setting mode after resetting each limit.

Set the Close Limit Only

1. Press and release the SET OPEN and SET CLOSE buttons simultaneously to enter limit setting mode.

3. Once the gate is in the desired close position, press and release the

STOP button on the remote control.

4. Press and release the CLOSE button on the remote control again to set the close limit.

When the close limit is set properly the operator will automatically exit limit setting mode.

Set the Open Limit Only

1. Press and release the SET OPEN and SET CLOSE buttons simultaneously to enter limit setting mode.

2. Press and hold the OPEN button on the remote control until the gate reaches the desired open position. The gate can be jogged back and forth using the OPEN and CLOSE buttons on the remote control.

3. Once the gate is in the desired open position, press and release the

STOP button on the remote control.

4. Press and release the OPEN button on the remote control again to set the open limit.

When the open limit is set properly the operator will automatically exit limit setting mode.

3-Button Remote Control programmed for OPEN, CLOSE, and

STOP

SET OPEN SET CLOSE

PRESS &

RELEASE

REPAIR PARTS

CONTROL BOX

ITEM PART DESCRIPTION

K74-36798-2

K94-36408-2

Standard Plastic Control Box Only

Reset Switch with Product ID

3 K94-36411 Piezo

4 K75-36635 Control Board Bracket

6 K76-36296-1 Outlet

7 APOW3 Transformer

8 K74-30762 Batteries

NOT SHOWN

K94-36274-1 7AH Battery Harness

LA400CONTDC

K74-30941

Standard Plastic Control Box (with control board)

ATC Fuse Kit Includes 20 Amp (1),

15 Amp (2)

GATE OPERATOR ARM

ITEM PART DESCRIPTION

1 LA400

3 41ASWG-438SA

5 41ASWG-489

NOT SHOWN

Motor with Limit Switch Harness

Cable 24 V with Connector

Complete with: Gate bracket, post bracket, pull-to-open bracket and hardware

WIRING DIAGRAM

STANDARD CONTROL BOX

To protect against fire and electrocution:

• DISCONNECT power and battery BEFORE installing or servicing

ECN: operator.

For continued protection against fire:

• Replace ONLY with fuse of same type and rating.

11/19/13

Coaxial Antenna Cable

Antenna

Red

12V 7AH Battery

Black

Two 12V Solar Panels in Series

To J15

Red

Blocking

Diode

Black

Attach to Metal Chassis

Accessory

Power Outlets

Primary Operator

Secondary Operator

GND

Transformer

(Optional)

Red

Black

Piezo Alarm

Reset Switch

Photoelectric Sensors

Attach to Outlet

Metal Chassis With a Single Screw

ACCESSORIES

ENTRAPMENT PROTECTION DEVICES

PHOTOELECTRIC SENSORS (MONITORED,

NON-CONTACT)

The photoelectric sensors are designed to detect an obstacle in the path of the electronic beam and stop the operator. Includes mounting brackets.

Models CPS-UN4 and CPS-RPEN4GM (LiftMaster low power accessory)

MISCELLANEOUS

REMOTE ANTENNA EXTENSION KIT

The remote antenna extension kit allows the antenna to be remotely installed.

Model 86LM

WIRELESS ACCESS CONTROL RECEIVER

Access control receiver for up to 450 remote controls.

Model STAR450-315

VEHICLE DETECTION DEVICES

PHOTOELECTRIC SENSORS (NON-MONITORED,

NON-CONTACT)

OPEN

The photoelectric sensors are designed to detect an obstacle in the path of the electronic beam and stop the operator. Includes mounting brackets.

Models AOMRON E3K-R10K4-NR (retro-reflective) and RETROAB 60-2728 (retro-reflective)

SENSING EDGE (2-WIRE, NON-MONITORED,

CONTACT)

Sensing edges can detect an obstacle upon contact and stop the operator.

Models G65MG0204, G65MG0205, G65MGR205, and G65MGS205

SENSING EDGE CHANNEL

Mounting channel for all MG020 type edges.

Model G65ME120C5

REMOTE CONTROLS

Chamberlain offers a variety of LiftMaster remote controls to satisfy your application needs. Single-button to 4-button, visor or key chain. The following remote controls are compatible with operators manufactured by

Chamberlain after 1993. Contact your authorized LiftMaster dealer for additional details and options.

3-BUTTON REMOTE CONTROL

The 3-button remote control can be programmed to control the operator. Includes visor clip.

Model 893MAX

3-BUTTON MINI-REMOTE CONTROL

The 3-button remote control can be programmed to control the operator. Includes key ring and fastening strip.

Model 890MAX

PLUG-IN LOOP DETECTOR

Low power. Conveniently plugs into existing control board.

Model LOOPDETLM

LOOP DETECTOR

Low power loop detectors mounted and wired separately inside control box. LiftMaster low power accessory.

Model LD7LP

VEHICLE SENSING PROBE

The vehicle sensing probe is buried in the ground and can detect a car as it approaches and will then open the gate.

Model CP3

PUSH-TO-OPEN BRACKET

Used to allow the gate operator to push the gate open.

Model 50-19503

SOLENOID GATE LOCK

The automatic gate lock is a solenoid-driven lock that automatically unlocks when the gate is open and locks when the gate is closed. Can be mounted onto a gate or post. Can be released in case of emergency.

Model GC824-12 (12/24 Vac/dc)

MAGNETIC GATE LOCK

Outdoor magnetic lock, transformer, junction box, mounting plate and hardware. Not for use with

Solar Applications. Must be powered separately.

Model MG1300 (12/24 Vdc)

TRANSFORMER

Model APOW3

KEYLESS ENTRY

Enables homeowner to operate gate operator from outside by entering a 4-digit code on a specially designed keypad.

Model 877MAX

SOLAR PANEL KIT - 10 WATT

This kit is to replace or add a solar panel to the operator application. Up to four solar panels can be connected to the operator. Requires a 33AH battery harness.

Model SOLPNL10W12V (requires 2 minimum)

EXPANSION BOARD

Model K1D8080-1CC

ACCESSORIES

BATTERIES

Gate access system batteries replace or upgrade the gate operator batteries. Two identical 12 Vdc batteries are required for each gate operator. Do not mix 7AH and 33AH batteries within a gate operator.

7AH BATTERIES

Standard 7 AMP-Hour Battery, 12 Vdc, to replace original batteries provided with operator. Reuse existing harnesses.

Model 29-NP712

33AH BATTERIES

Upgrade 33 AMP-Hour Battery, 12 Vdc. Ideal for solar applications and extended battery backup. For use with Large Metal Control Box ONLY.

Model A12330SGLPK

BATTERY TRAY

Required for 33AH applications.

Model K10-36183)

SOLAR BATTERY HARNESS

Required for 33AH applications.

Model K94-37236

WARRANTY

LIFTMASTER TWO YEAR LIMITED WARRANTY

The Chamberlain Group, Inc. warrants to the first purchaser of this product, for the structure in which this product is originally installed, that it is free from defect in materials and/or workmanship for a period of TWO years from the date of purchase. The proper operation of this product is dependent on your compliance with the instructions regarding installation, operation, maintenance and testing. Failure to comply strictly with those instructions will void this limited warranty in its entirety.

If, during the limited warranty period, this product appears to contain a defect covered by this limited warranty, call 1-800-528-2806, toll free, before dismantling this product. Then send this product, pre-paid and insured, to our service center for warranty repair. You will be advised of shipping instructions when you call. Please include a brief description of the problem and a dated proof-of purchase receipt with any product returned for warranty repair. Products returned to Seller for warranty repair, which upon receipt by Seller are confirmed to be defective and covered by this limited warranty, will be repaired or replaced (at Seller’s sole option) at no cost to you and returned pre-paid. Defective parts will be repaired or replaced with new or factory-rebuilt parts at Seller’s sole option.

ALL IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE TWO YEAR LIMITED WARRANTY PERIOD SET FORTH ABOVE, AND

NO IMPLIED WARRANTIES WILL EXIST OR APPLY AFTER SUCH PERIOD. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. THIS LIMITED WARRANTY DOES NOT COVER NON-DEFECT DAMAGE, DAMAGE CAUSED BY

IMPROPER INSTALLATION, OPERATION OR CARE (INCLUDING, BUT NOT LIMITED TO ABUSE, MISUSE, FAILURE TO PROVIDE REASONABLE AND

NECESSARY MAINTENANCE, UNAUTHORIZED REPAIRS OR ANY ALTERATIONS TO THIS PRODUCT), LABOR CHARGES FOR REINSTALLING A

REPAIRED OR REPLACED UNIT, OR REPLACEMENT OF BATTERIES.

THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH, OR RELATING TO, THE GATE OR GATE HARDWARE, INCLUDING BUT NOT

LIMITED TO THE GATE SPRINGS, GATE ROLLERS, GATE ALIGNMENT OR HINGES. THIS LIMITED WARRANTY ALSO DOES NOT COVER ANY

PROBLEMS CAUSED BY INTERFERENCE. ANY SERVICE CALL THAT DETERMINES THE PROBLEM HAS BEEN CAUSED BY ANY OF THESE ITEMS

COULD RESULT IN A FEE TO YOU.

UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES ARISING IN CONNECTION

WITH USE, OR INABILITY TO USE, THIS PRODUCT. IN NO EVENT SHALL SELLER’S LIABILITY FOR BREACH OF WARRANTY, BREACH OF

CONTRACT, NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST OF THE PRODUCT COVERED HEREBY. NO PERSON IS AUTHORIZED TO

ASSUME FOR US ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT.

Some states do not allow the exclusion or limitation of consequential, incidental or special damages, so the above limitation or exclusion may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

TEMPLATE FOR POST BRACKET MOUNTING

7 6 5 4 3 2 1

01-37070B

845 Larch Avenue

Elmhurst, Illinois 60126-1196 www.liftmaster.com

Key features

24 VDC actuator arm
Single or dual gate applications
Compatibility with MyQ® and Security+ 2.0™ accessories
Residential use
Convenient and secure operation

Frequently asked questions

This model is intended for use in Class I, II, and III vehicular swing gate applications.

There are three models: LA4001PKGDC, LA400DC, and LA400DCS. The LA4001PKGDC is a single-arm package, while the LA400DC and LA400DCS can be used for single or dual gate applications.

This model is for use on vehicular passage gates ONLY and not intended for use on pedestrian passage gates.

This gate operator is compatible with MyQ® and Security+ 2.0™ accessories.