IMPORTANT! KEEP THIS MANUAL FOR FUTURE REFERENCE!

INSTRUCTION MANUAL FOR

USE OF CHILD RESTRAINT SYSTEM

„MY SIZE”

This child restraint system is manufactured in compliance with the requirements of Regulation No 129 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of enhanced Child Restraint Systems used on board of motor vehicles (ECRS), the provisions of the Product safety Directive 2001/95/EU of the European Parliament and The Council as well as the Consumer Protection

Law of Bulgarian Legislation.

Car seat “MY SIZE” is suitable for children with height 40-150 cm, age 0-12 years.

Position of car seat Child’s height

REARWARD facing

FORWARD facing

FORWARD facing

40-105 cm

76-105 cm

100-150 cm

Approx age of child Car seat installation

0-4 years

15 months - 4 years

3-12 years

ISOFIX

+

Top tether

+

Car seat safety belt for secure the child

ISOFIX

+

Top tether

+

Car seat safety belt for secure the child

ISOFIX

+

3-point vehicle belt

N O T I C E

Size range: 40-105 cm

This is an “i-Size” Child Restraint System. It is approved to Regulation No.129, for use in,

“i-Size compatible” vehicle seating positions as indicated by vehicle manufacturers in the vehicle users’ manual.

If in doubt, consult either the child restraint manufacturer or the retailer.

Size range: 100-135 cm

This is an “i-Size” Booster seat Child Restraint System. It is approved to Regulation No.129, for use primarily in, “i-Size seating positions” as indicated by vehicle manufacturers in the vehicle users’ manual.

If in doubt, consult either the child restraint manufacturer or the retailer.

Size range: 135-150 cm

This is an “i-Size” Booster seat Child Restraint System. It is approved to Regulation No.129, for use primarily in, “i-Size seating positions” as indicated by vehicle manufacturers in the vehicle users’ manual.

If in doubt, consult either the child restraint manufacturer or the retailer.

CAUTION!

The child restraint is suitable for use in vehicles, equipped with APPROVED 3-POINT

SAFETY BELTS WITH RETRACTOR in compliance with ECE R16 of (UN/ECE).

1

DO NOT FORGET THAT NO RESTRAINT SYSTEM CAN PROVIDE

ABSOLUTE PROTECTION IN CASE OF A CRASH OR ROAD ACCIDENT!

DRIVE WITH CARE WHEN THERE IS A CHILD IN YOUR VEHICLE!

IN ORDER TO ENSURE THE SAFETY OF YOUR CHILD,

FOLLOW EXACTLY THE INSTRUCTIONS AND SAFETY

RECOMMENDATIONS IN THIS MANUAL!

MISUSE OF THE CAR SEAT WILL CONTRIBUTE TO REDUCING ITS SECURITY

AND SAFETY FEATURES! FAILURE OF THE GUIDELINES OF THIS

INSTRUCTION INCREASES THE RISK OF SERIOUS INJURY OR DEATH!

CAUTION !

1. NEVER INSTALL THE CAR SEAT IN “FORWARD FACING” POSITION BEFORE THE

CHILD’S AGE EXCEEDS 15 MONTHS!

2. DO NOT PLACE THE RESTRAINT SYSTEM ON A VEHICLE SEAT EQUIPPED WITH AIR

BAG! THIS MAY RESULT IN DEATH OR SERIOUS! Review the instructions of the vehicle

for information about airbags and conditions of transportation of children.

3. DO NOT USE ANCHOR POINTS OTHER THAN THE ONES DESCRIBED IN THIS MANUAL

AND MARKED ON THE RESTRAINT SYSTEM!

1

2

!

NEVER INSTALL THE CAR SEAT IN

VEHICLE WITH 2-POINT BELT! INSTALL IT ONLY IN

VEHICLE WITH 3-POINT BELT!

1

2

DIAGONAL BELT

LAP BELT

Rearward facing installation of the car seat

Height of the child: 40-105 cm

2

Forward facing installation of the car seat

Height of the child: 76-150 cm

?

1

?

2

?

1

Do not install on seat, equipped with air bag.

?

2 Place the car seat ONLY on a vehicle seat with a 3-point seat safety belt.

CAUTION! WARNINGS!

 CAUTION!

NEVER LEAVE YOUR CHILD UNATTENDED!

 CAUTION!

DO NOT USE ANCHOR POINTS OTHER THAN THE ONES DESCRIBED IN THIS

MANUAL AND MARKED ON THE RESTRAINT SYSTEM.

 CAUTION!

WHEN YOU INSTALL THE CAR SEAT IN POSITION „REARWARD FACING“, NEVER

PLACE IT ON PASSENGER SEAT, EQUIPPED WITH AIRBAG! THIS MAY LEAD TO SERIOUS

INJURY OR DEATH!

 CAUTION!

NEVER INSTALL THE CAR SEAT IN DIRECTION OF NORMAL MOVEMENT OF THE

VEHICLE AND POSITION OF THE CHILD "FORWARD FACING" BEFORE THE CHILD EXCEEDS

15 MONTHS OLD!

 CAUTION!

THE VEHICLE SAFETY BELTS WHICH HOLD THE CAR SEAT TO THE PASSENGER

SEAT MUST BE TIGHTENED AND FIXED!

 CAUTION!

THE CAR SEAT SAFETY BELTS MUST BE PROPERLY ADJUSTED ACCORDING TO

CHILD’S HEIGHT, NOT TWISTED AND SNUG WELL AGAINST BABY’S BODY.

 THE LAP BELT MUST BE PLACED LOW DOWN, SO THAT THE PELVIS IS FIRMLY ENGAGED

WITHOUT PRESSING!

 CAUTION!

DO NOT MAKE CHANGES, ADDITIONS OR MODIFICATIONS ON THE CAR SEAT

WITHOUT THE APPROVAL OF THE NOTIFYING AUTHORITY ! IT IS DANGEROUS NOT TO

KEEP STRICTLY THE INSTRUCTIONS GIVEN BY THE MANUAFACTURER!

 CAUTION!

KEEP AWAY FROM FIRE!

 Installation in the vehicle and securing the child in the car seat to be done only by adult!

 The hard parts and the parts of the child restraint made of plastic should be located and installed

so that when the vehicle is in normal use, they can not be trapped by a sliding seat or in a door of

the vehicle.

 Do not allow the safety belts of the car seat and the vehicle to be twisted, frayed or torn, latches and

locks (buckles) must be always in good order and firmly fixed.

 If you find uncertainty or defect in the structure, latches, straps or locking mechanisms of the car

seat or ISOFIX attachments , discontinue usage until removal of the damaged parts and

replacement with new ones.

 After a violent impact the car seat and belts may be damaged, therefore, it is recommended to

replace the car seat with a new one.

 Never use a second hand child restraint. It may have suffered structural damage, which may make

the child restraint extremely dangerous.

3

 Do not use this car seat without its seat cover and do not replace it with a new one, unless supplied

by the manufacturer. The fabric parts are integral parts of the restraint system and its safety

features!

 Any luggage or other objects that could cause injury in the event of a collision must be well secured.

Remove or secure at a safe distance from the seat and child any luggage that may cause injury in

the event of a sudden stop or accident while driving.

 Always check that the seat is firmly attached to the vehicle seat, even when you are not placing a

child in it. A loose car seat, even without a child in it, can cause injury in the event of a collision.

 Do not put additional pads except the ones supplied from the manufacturer!

 Do not use spare parts and other components not supplied by the manufacturer. The manufacturer

assumes no responsibility for safety in the event that are used spare parts other than original.

 Keep the instructions for use in the space provided in the car seat or in the vehicle in which you are

going to use the car seat.

 Do not expose the car seat to direct sunlight to prevent the child from burning, deforming the car seat

and especially the plastic parts.

 The car seat does not replace the child's cot or bed. When a child needs a sleep, you have to place

him/her in a suitable baby stroller, baby crib or bed.

 Do not attach objects with long cords or strings on the car seat in order to avoid danger of

suffocation!

 Never place the car seat on beds, couches or similar soft surfaces!

 Do not allow children to play with the product!

 Do not remove stickers and warnings – they contain important information!

 The packaging of the product must be kept out of the reach of children at the time of and after

unpacking in order to avoid the risk of strangulation!

PRODUCT FEATURES

 This is I-Size child restraint system, suitable for children with height 40-150 cm, age 0-12 years.

 The child restraint rotates 360 degrees on the base;

 Backrest recline;

 Headrest height adjustment;

 5-point safety harness on the restraint;

 Additional soft pads;

4

MAIN PARTS

Fabric cover

Soft pad

5-point safety belt

Strap for belt’s length adjustment

Level to rotate the seat

Handle to adjust the head support’s height

Adjustable head support

Shoulder belts

Button to adjust the belt’s length

Top tether

Cover’s lock

Cover

ISOFIX attachment anchors

Side protection

ISOFIX button

INSTRUCTIONS FOR USE OF THE CHILD RESTRAINT SYSTEM

IMPORTANT!

• Follow exactly the instructions and sequence of installation steps and use of the product described

in the text and figures of this manual.

• Check the security of fixing after each operation!

• ALWAYS CHECK THE SECURITY OF FIXING OF THE SAFETY BELTS!

• After each installation make sure that the seat belts are not twisted and they are in the correct

position.

5

CHILD’S HEIGHT 40-105 cm

INSTALLATION OF THE CAR SEAT IN “REARWARD FACING” POSITION

ISOFIX + TOP TETHER + 5-POINT BELT OF CAR SEAT attachmnet point

ISOFIX guide click

6

7

“щрак”

1. Pull the handle to adjust the recline.

2. Set in required position – 1, 2, 3, 4.

3. Pull the level and adjust the seat in REARWARD facing position (fig. 4).

4. Select the lying position correcponding with REARWARD facing (fig 4).

ATTENTION!

Make sure that your vehicle is equipped with ISOFIX attachment points!

5. Install the ISOFIX guide to the ISOFIX attachmnet point of vehicle.

6. Release the ISOFIX anchors and set them maximum out.

7. Insert ISOFIX anchors of car seat to ISOFIX attachment point of vehicle.

8. You must hear click sound by fixing.

9. CAUTION!

ISOFIX anchors are fixed when both of them are fully green.

Note: If indicators are red, do the installation again following the above described sequence of

actions.

10. Press the car seat until it reaches the backrest of vehicle’s seat.

11. and 12 Try to pull the car seat to assure that ISOFIC anchors are fixed to ISOFIX attchment point of

vehicle.

PLACES AND WAYS TO ATTACH THE TOP TETHER TO VEHICLE

A

D

B C

Places to attach to top tether to different vehicles can be located at one of the shown in figure – A,

B, C or D. Before installing the car seat, you must check this in instruction manual of the vehicle.

13. Press the button of buckle for adjustment of top tether’s length and pull it at maximum.

14. Thread the top tether belt through the one of the side guides of car seat.

15. Attach the hook of top tether to the attachmnet point of your vehicle. Note: Belt must not be twisted.

16. Tighten the top tether.

17. After tightning indicator of top tether belt must be fully green.

Note: If indicator is red, do the installation again following the above described sequence of actions.

18. Make sure that car seat is stable fixed.

19, 20 Press the button for belts adjustment and at the same time pull the shoulder belts towards you.

21, 22 Press the button at central buckle to release the belts and place the child in car seat.

23, 24 Pull the handle for head rest adjustment and set the head support in suitable position (see the figure - correct height).

25, 26 Join the shoulder belts into the central buckle. Pull the strap that adjusts the length of belts so that

the belts hold will the body of child without bringing pressure and discomfort to the child.

Recommened space between child’s body and belts is 1-2 cm.

8

!

ATTENTION!

Soft pad

For child’s height:

• 40 up to 75 cm use soft pad of the seat and

3D pillow of the waist.

• 76 up to 80 cm use only the soft pad of the

seat.

3D pillow for the waist

CHILD’S HEIGHT 76-105 cm

INSTALLATION OF THE CAR SEAT IN “FORWARD FACING” POSITION

ISOFIX + TOP TETHER + 5-POINT BELT OF CAR SEAT attachmnet point

ISOFIX guide ISOFIX button click

9

10

Soft pad

1. ATTENTION!

Make sure that your vehicle is equipped with ISOFIX attachment points!

Install the ISOFIX guide to the ISOFIX attachmnet point of vehicle.

2. Release the ISOFIX anchors by pressing the ISOFIX buttons . Set them maximum out.

3. Insert ISOFIX anchors of car seat to ISOFIX attachment point of vehicle.

4. You must hear click sound by fixing.

5. CAUTION!

ISOFIX anchors are fixed when both of them are fully green.

Note: If indicators are red, do the installation again following the above described sequence of

actions.

Adjust the recline in position 1, 2, 3 or 4.

6. Press the car seat until it reaches the backrest of vehicle’s seat.

7. and 8 Try to pull the car seat to assure that ISOFIX anchors are fixed to ISOFIX attchment point of

vehicle.

9. Press the button of buckle for adjustment of top tether’s length and pull it at maximum.

10. Attach the hook of top tether to the attachmnet point of your vehicle. Note: Belt must not be twisted.

11. Tighten the top tether.

12. After tightning indicator of top tether belt must be fully green.

Note: If indicator is red, do the installation again following the above described sequence of actions.

13. Make sure that car seat is stable fixed.

14, 15. Press the button for belts adjustment and at the same time pull the shoulder belts towards you.

16, 17 Press the button at central buckle to release the belts and place the child in car seat.

18, 19, 20 Pull the handle for head rest adjustment and set the head support in suitable position

(see the figure - correct height).

21, 22 Join the shoulder belts into the central buckle. Pull the strap that adjusts the length of belts so that

the belts hold will the body of child without bringing pressure and discomfort to the child.

Recommened space between child’s body and belts is 1-2 cm.

!

ATTENTION!

Soft pad

For child’s height:

• 76 up to 80 cm use only soft pad of the seat

11

CHILD’S HEIGHT 100-150 cm

INSTALLATION OF THE CAR SEAT IN “FORWARD FACING” POSITION

3-POINT BELT OF VEHICLE

“click”

12 lap belt

click

1. Press the button at central buckle to release the belt.

2. Lift the upper part fo the seat cover as figure shows.

3. Press the button for belts adjustment and at the same time pull the shoulder belts towards you.

4. Unfasten the down part of the seat cover and place it down as figure shows.

5. Fix the belts and cover them with both parts of the seat cover.

6. Place the central buckle in car seat’s slot.

7. Remove the soft pad.

8. Place the child in car seat.

9. Pull the handle for head rest adjustment and set the head support in suitable position

(see the figure - correct height).

10. Thread the lap belt through the guide under the armrest of car seat and above the legs of the child.

Make sure the belt snugs will the child’s pelvis.

11. Thread the diagonal belt through the guide at the upper part of backrest.

12. Lock the 3-pont belt of vehicle into the buckle of vehicle’s seat.

CAUTION!

Make sure that belt is not twisted.

CHILD’S HEIGHT 100-150 cm

INSTALLATION OF THE CAR SEAT IN “FORWARD FACING” POSITION

3-POINT BELT OF VEHICLE + ISOFIX attachment point

ISOFIX guide click

ISOFIX button

13

click

ATTENTION!

Make sure that your vehicle is equipped with ISOFIX attachment points!

1. Hide the car seat belts and remove the soft pad.

2. Set the recline is position 1.

3. Install the ISOFIX guide (option) to the ISOFIX attachmnet point of vehicle.

4. Release the ISOFIX anchors by pressing the ISOFIX buttons . Set them maximum out.

5. Insert ISOFIX anchors of car seat to ISOFIX attachment point of vehicle.

6. You must hear click sound by fixing.

7. CAUTION!

ISOFIX anchors are fixed when both of them are fully green.

Note: If indicators are red, do the installation again following the above described sequence of

actions.

8. Press the car seat until it reaches the backrest of vehicle’s seat.

9. and 10 Try to pull the car seat to assure that ISOFIX anchors are fixed to ISOFIX attchment point of

vehicle.

11. Place the child in car seat.

12. Pull the handle for head rest adjustment and set the head support in suitable position

(see the figure - correct height).

13. Thread the lap belt through the guide under the armrest of car seat and above the legs of the child.

Make sure the belt snugs will the child’s pelvis.

14. Thread the diagonal belt through the guide at the upper part of backrest.

15. Lock the 3-pont belt of vehicle into the buckle of vehicle’s seat.

CAUTION!

Make sure that belt is not twisted.

14

REMOVING AND PLACING THE SEAT COVER

Soft pad

1. Hide the car seat belts and remove the soft pad.

2. Remove the fabric cover of head support.

3. Unfasten and remove the fabric cover under the head support.

4. Remove all the rest of seat fabric cover.

To place the cover back, do the same actions in opposite order.

CARE AND MAINTENANCE

 Clean the fabrics, plastic parts and metal parts with damp cotton cloth or sponge and mild soap

 Fabric cover and soft pads may be hand washed at 30 ̊С using mild detergent!

 Do not bleach! Do not tumble dry! Do not machine wash! Do not iron!

 Do not use abrasive, bleach or other aggressive detergents.

 Always after cleaning leave the car seat fully dry and after that use it or store it.

 Harnesses must be cleaned with damp cloth and mild soap!

 Do not wet or remove the stickers. They contain important information!

 Always store your car seat indoors – on dry and clean place. Do not expose to direct environment influence - sun, rain, moisture and high temperature intervals.

 Please, contact your authorized dealer for problems connected with the use or repair.

Fabric:

Outer: 100% polyester

Filling: 100% polyester

Materials used: plastic, metal, textile

STKMS022xxxx

15

List of vehicles that are suitable for installation of child restraint system “MY SIZE” as booster seat for specific vehicle.

Vehicle Model ISOFIX

3-point belt of the vehicle

16

Vehicle Model ISOFIX

3-point belt of the vehicle

17

Vehicle Model ISOFIX

3-point belt of the vehicle

18

Bulgaria, Plovdiv, Str. Golyamokonarsko shosse № 1 www.chipolino.com