Viewsonic X2 PROJECTOR User Guide
Annons
Annons
X1/X2
Projector
User Guide
IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this
User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http://www.viewsonic.com in English, or in specific languages using the Regional selection box in the upper right corner of our website. “Antes de operar su equipo lea cu idadosamente las instrucciones en este manual”
Model No. VS18969 / VS19041
Model Name: X1/X2
Thank you for choosing ViewSonic®
As a world-leading provider of visual solutions, ViewSonic® is dedicated to exceeding the world’s expectations for technological evolution, innovation, and simplicity.
At ViewSonic®, we believe that our products have the potential to make a positive impact in the world, and we are confident that the ViewSonic® product you have chosen will serve you well.
Once again, thank you for choosing ViewSonic®!
ii
Safety Precautions
P lease read the follo wing Safety Precautions before you start using the projector.
• Keep this user guide in a safe place for later reference.
• Read all warnings and follow all instructions.
• Allow at least 20“ (50 cm) clearance around the projector to ensure proper ventilation.
• Place the projector in a well-ventilated area. Do not place anything on the projector that prevents heat dissipation.
• Do not place the projector on an uneven or unstable surface. The projector may fall over, causing personal injury or projector malfunction.
• Do not look straight at the projector lens during operation. The intense light beam may damage your eyes.
• Always open the lens shutter or remove the lens cap when the projector lamp is on.
• Do not block the projection lens with any objects when the projector is under operation as this could cause objects to become heated and deformed or even cause a fire.
• The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement.
• Do not use lamps beyond the rated lamp life. Excessive use of lamps beyond the rated life could cause them to break on rare occasions.
• Never replace the lamp assembly or any electronic component unless the projector is unplugged.
• Do not attempt to disassemble the projector. There are dangerous high voltages inside which may cause death if you should come into contact with live parts.
• When moving the projector, be careful not to drop or bump the projector on anything.
• Do not place any heavy objects on the projector or connection cables.
• Do not stand the projector on end vertically. Doing so may cause the projector to fall over, causing personal injury or projector malfunction.
• Avoid exposing the projector to direct sunlight or other sources of sustained heat. Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including amplifiers) that may increase the temperature of the projector to dangerous levels.
iii
• Do not place liquids near or on the projector. Liquids spilled into the projector may cause it to fail. If the projector does become wet, disconnect it from the power supply and call your local service center to have the projector serviced.
• When the projector is under operation, you may sense some heated air and odor from its ventilation grill. It is a normal operation and not a defect.
• Do not attempt to circumvent the safety provisions of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide and third blade are provided for your safety. If the plug does not fit into your outlet, obtain an adapter and do not attempt to force the plug into the outlet.
• When connecting to a power outlet, DO NOT remove the grounding prong.
Please ensure grounding prongs are NEVER REMOVED.
• Protect the power cord from being treaded upon or pinched, particularly at the plug, and at the point where it emerges from the projector.
• In some countries, the voltage is NOT stable. This projector is designed to operate safely within a voltage between 100 to 240 volts AC, but could fail if power cuts or surges of ±10 volts occur. In areas where voltage may fluctuate or cut out, it is recommended that you connect your projector through a power stabilizer, surge protector, or uninterruptable power supply (UPS).
• If smoke, an abnormal noise, or a strange odor is present, immediately switch the projector off and call your dealer or ViewSonic®. It is dangerous to continue using the projector.
• Use only attachments/accessories specified by the manufacturer.
• Disconnect the power cord from the AC outlet if the projector is not being used for a long period of time.
• Refer all servicing to qualified service personnel.
CAUTION: Possibly hazardous optical radiation is emitted from this product. As with any bright light source, do not stare into the beam, RG2 IEC 62471-
5:2015 iv
Safety Precautions - Ceiling Mounting
Please read the following Safety Precautions before you start using the projector.
If you intend to mount the projector on the ceiling, it is strongly recommended that you use a proper fitting projector ceiling mount kit and that you ensure it is securely and safely installed.
If you use an inappropriate projector ceiling mount kit, there is a safety risk that the projector may fall from the ceiling due to an improper attachment through the use of the wrong gauge or length screws.
You can purchase a projector ceiling mount kit from the place you purchased your projector. v
Contents
Introduction ................................................................ 5
Package Contents ...................................................................................................5
Product Overview ...................................................................................................6
Projector .................................................................................................................. 6
Controls and Functions ................................................................................................. 6
Connection Ports ........................................................................................................... 7
Remote Control ....................................................................................................... 8
Controls and Functions ................................................................................................. 8
Remote Control Effective Range ................................................................................... 9
Replacing the Remote Control Batteries ..................................................................... 10
Initial Setup ............................................................... 11
Choosing a Location ..............................................................................................11
Projection Dimensions ..........................................................................................12
16:9 Image on a 16:9 Screen ....................................................................................... 12
X1 ................................................................................................................................ 12
X2 ................................................................................................................................ 13
16:9 Image on a 4:3 Screen ......................................................................................... 13
X1 ................................................................................................................................ 13
X2 ................................................................................................................................ 14
Mounting the Projector ........................................................................................15
Preventing Unauthorized Use ...............................................................................16
Using the Security Slot .......................................................................................... 16
Using the Password Function ................................................................................ 17
Setting a Password ...................................................................................................... 17
Changing the Password ............................................................................................... 18
Disabling the Password Function ................................................................................ 18
Forgetting the Password ............................................................................................. 19
Password Recall Procedure ......................................................................................... 19
Locking the Control Keys ....................................................................................... 20
Making Connections .................................................. 21
Connecting to Power ............................................................................................21
Connecting to Video/Computer Sources ..............................................................22
HDMI Connection .................................................................................................. 22
USB C Connection .................................................................................................. 22
Connecting to Audio .............................................................................................22
vi
Operation .................................................................. 24
Turning the Projector On/Off ...............................................................................24
Starting Up the Projector ...................................................................................... 24
First Time Activation ................................................................................................... 24
Shutting Down the Projector ................................................................................. 25
Selecting an Input Source .....................................................................................26
Adjusting the Projected Image .............................................................................27
Adjusting the Projector's Height and Projection Angle ............................................... 27
Fine-Tuning the Image Size and Clarity ................................................................. 27
Correcting Keystone .............................................................................................. 28
Adjusting 4 corners ............................................................................................... 29
Hiding the Image ..................................................................................................29
Menu Functions ........................................................ 30
General On-Screen Display (OSD) Menu Operation .............................................30
On-Screen Display (OSD) Menu Tree ....................................................................31
DISPLAY Menu ......................................................................................................36
IMAGE Menu ........................................................................................................39
POWER MANAGEMENT Menu .............................................................................42
BASIC Menu ..........................................................................................................45
ADVANCED Menu .................................................................................................48
SYSTEM Menu .......................................................................................................52
INFORMATION Menu ...........................................................................................54
Smart System ............................................................ 55
Home Screen ........................................................................................................55
Menu Operations .................................................................................................56
Media control bar buttons ...................................................................................61
Supported file formats .........................................................................................61
Firmware upgrade ................................................................................................62
System related settings ........................................................................................67
vii
Appendix ................................................................... 70
Specifications ........................................................................................................70
Projector Dimensions ............................................................................................ 71
Timing Chart .........................................................................................................71
Troubleshooting ...................................................................................................74
Common Problems ................................................................................................ 74
LED Indicator ......................................................................................................... 75
Maintenance.........................................................................................................76
General Precautions .............................................................................................. 76
Cleaning the Lens .................................................................................................. 76
Cleaning the Case .................................................................................................. 76
Storing the Projector ............................................................................................. 76
Disclaimer .............................................................................................................. 76
Light Source Information ......................................................................................77
Light Source Hour .................................................................................................. 77
Extending Light Source Life ................................................................................... 77
Regulatory and Service Information .......................... 78
Compliance Information .......................................................................................78
FCC Compliance Statement ................................................................................... 78
FCC Radiation Exposure Statement ....................................................................... 79
Industry Canada Statement ................................................................................... 79
IC Warning Statement ........................................................................................... 79
Country Code Statement ....................................................................................... 79
IC Radiation Exposure Statement .......................................................................... 80
CE Conformity for European Countries ................................................................. 80
Declaration of RoHS2 Compliance ......................................................................... 81
Indian Restriction of Hazardous Substances ......................................................... 82
Product Disposal at End of Product Life ................................................................ 82
Copyright Information ..........................................................................................83
Customer Service .................................................................................................. 84
Limited Warranty .................................................................................................. 85
Mexico Limited Warranty ...................................................................................... 88 viii
Introduction
Package Contents
NOTE: The power cord and video cables included in your package may vary depending on your country. Please contact your local reseller for more information.
5
Product Overview
Projector
MENU
EXIT
BLANK
SOURCE
?
ENTER
COLOR
MODE
Vent (heated air exhaust)
Indicator Light
Vent (cold air intake)
X1
Lens shift (up/down)
*The lens shift function is only available on specific model.
Vent (cold air intake)
Focus Ring
Zoom Ring
Projection Lens
Controls and Functions
X2
Key
[ ] Power
MENU
EXIT
[ / / / ]
Left/Right/Up/Down
SOURCE
BLANK
ENTER
COLOR MODE
Description
Toggles the projector between standby mode and Power On.
• Turns on or off the On-Screen Display (OSD) Menu.
• Goes back to previous OSD menu, exits and saves menu settings.
When the input source is SMART SYSTEM
Moves through the menu items or toggle through the available options.
When the input source is not SMART SYSTEM
• Manually corrects distorted images resulting from an angled projection.
• Selects the desired menu items and makes adjustments when the On-Screen Display (OSD) Menu is activated.
• Displays the input source selection bar.
• Displays the HELP menu by a long press for 3 seconds.
Hides the screen picture.
When the input source is SMART SYSTEM
Confirms the selected menu item.
When the input source is not SMART SYSTEM
• Displays the Corner Adj. menu.
• Enacts the selected On-Screen Display (OSD) Menu item when the OSD Menu is activated.
Displays the color mode selection bar.
6
Connection Ports
1 2 3
AUDIO IN
RS232
AUDIO OUT
4 5
SERVICE HDMI 1
HDCP 2.2
HDMI 2
HDCP 2.2
6
USB C
AC Power Cord Inlet
7
USB A
5V/1A
Reset button for SMART SYSTEM
Kensington Anti-theft Lock Slot
Remote IR sensor
Security Bar
Ceiling Mount Holes
Port
[1] AUDIO IN
[2] AUDIO OUT
[3] RS-232
[4] SERVICE
[5] HDMI 1, HDMI 2
[6] USB C
[7] USB A 5V/1A OUT
Adjuster Foot
Description
Audio signal input socket.
Audio signal output socket.
RS-232 control port.
For service personnel only.
HDMI ports.
USB Type-C port.
USB Type A port for power supply.
Remote Control
Controls and Functions
When the input source is SMART SYSTEM
Button
Power
Description
Toggles between standby mode and Power On.
Not available.
Left/ Right
Up/ Down
OK
Displays the source selection bar.
Displays the Bluetooth menu.
Selects the desired menu items and makes adjustments.
Confirms the selected menu item.
Turns on/off the On-
Screen Display (OSD)
Menu or goes back to previous OSD Menu.
Button Description
Returns to the previous menu, main settings menu or exit the app.
Goes to the homepage of the SMART SYSTEM.
Increases the projector volume.
Decreases the projector volume.
Mutes or unmutes the projector volume.
Plays or pauses the playback of a file.
Fast forwards the file or goes to the next one.
Rewinds the file or goes to the previous one.
When the input source is not SMART SYSTEM
Button
Power
Description
Toggles between standby mode and Power On.
Not available.
Displays the source selection bar.
Not available.
Left/ Right
Up/ Down
OK
• Manually corrects distorted images resulting from an angled projection.
• Selects the desired menu items and makes adjustments when the On-Screen
Display (OSD) Menu is activated.
Confirms the selected menu item.
Turns on/off the On-
Screen Display (OSD)
Menu or goes back to previous OSD Menu.
8
Button Description
Exits and saves menu settings.
Goes to the homepage of the SMART SYSTEM.
Increases the projector volume.
Decreases the projector volume.
Mutes or unmutes the projector volume.
Not available.
Remote Control Effective Range
To ensure proper function of the remote control follow the steps below:
1. The remote control must be held at an angle within 30° perpendicular to the projector’s IR remote control sensor(s).
2. The distance between the remote control and the sensor(s) should not exceed 8 m (26 ft.)
NOTE: Refer to the illustration for the location of the infrared (IR) remote control sensor(s).
USB C
USB A
5V/1A
9
Replacing the Remote Control Batteries
1. Remove the battery cover from the rear of the remote control by pressing the finger grip and sliding it down.
2. Remove any existing batteries (if necessary) and install two AAA batteries.
NOTE: Observe the battery’s polarities as indicated.
3. Replace the battery cover by aligning it with the base and pushing it back into position.
NOTE:
• Avoid leaving the remote control and batteries in excessive heat or a humid environment.
• Replace only with the same or equivalent type recommended by the battery manufacturer.
• Dispose of the used batteries according to the manufacturer’s instructions and local environment regulations for your region.
• If the batteries are drained or if you will not be using the remote control for an extended period of time, remove the batteries to avoid damage to the remote control.
10
Initial Setup
This section provides detailed instructions for setting up your projector.
Choosing a Location
Personal preference and room layout will decide the installation location. Consider the following:
• Size and Position of your screen.
• Location of a suitable power outlet.
• Location and Distance between the projector and other equipment.
The projector is designed to be installed in one of the following locations:
1. Front
The projector is placed near the floor in front of the screen.
2. Front Ceiling
The projector is suspeneded upsidedown from the ceiling in front of the screen.
3. Rear Ceiling
The projector is suspended upside-down from the ceiling behind the screen.
NOTE: A special rear projection screen is required.
4. Rear
The projector is placed near the floor behind the screen.
NOTE: A special rear projection screen is required.
11
Projection Dimensions
NOTE: See “Specifications” on page 63 for the native display resolution of this projector.
• 16:9 Image on a 16:9 Screen
Lens shift
(up/down)
• 16:9 Image on a 4:3 Screen
Lens shift
(up/down)
(a)
(e)
(f)
Lens shift
(up/down)
(c)
NOTE: (e) = Screen
(f) = Center of Lens
• 16:9 Image on a 16:9 Screen
Lens shift
(up/down)
(d)
(b)
X1
(a) Screen
Size
(b) Projection Distance minimum maximum
(c) Image
Height
(d) Vertical Offset minimum maximum inch mm inch mm inch mm inch mm inch mm inch mm
30 762 30 767 39 998 15 374 1 37 4.4
112
60 1524 60 1535 79 1995 29 747 3 75 8.8
224
70 1778 70 1791 92 2328 34 872 3 87 10.3 262
80 2032 81 2046 105 2660 39 996 4 100 11.8 299
90 2286 91 2302 118 2993 44 1121 4 112 13.2 336
100 2540 101 2558 131 3325 49 1245 5 125 14.7 374
110 2794 111 2814 144 3658 54 1370 5 137 16.2 411
120 3048 121 3069 157 3990 59 1494 6 149 17.6 448
130 3302 131 3325 170 4323 64 1619 6 162 19.1 486
140 3556 141 3581 183 4655 69 1743 7 174 20.6 523
150 3810 151 3837 196 4988 74 1868 7 187 22.1 560
200 5080 201 5116 262 6651 98 2491 10 249 29.4 747
250 6350 252 6395 327 8313 123 3113 12 311 36.8 934
300 7620 302 7674 393 9976 147 3736 15 374 44.1 1121
12
X2
(a) Screen
Size
(b) Projection Distance minimum maximum
(c) Image
Height
(d) Vertical Offset minimum maximum inch mm inch mm inch mm inch mm inch mm inch mm
30 762 18 455 21 546 15 374 1 19 0.7
19
60 1524 36 909 43 1091 29 747 1 37 1.5
37
70 1778 42 1061 50 1273 34 872 2 44 1.7
44
80 2032 48 1213 57 1455 39 996 2 50 2.0
50
90 2286 54 1364 64 1637 44 1121 2 56 2.2
56
100 2540 60 1516 72 1819 49 1245 2 62 2.5
62
110 2794 66 1667 79 2001 54 1370 3 68 2.7
68
120 3048 72 1819 86 2183 59 1494 3 75 2.9
75
130 3302 78 1971 93 2365 64 1619 3 81 3.2
81
140 3556 84 2122 100 2547 69 1743 3 87 3.4
87
150 3810 90 2274 107 2728 74 1868 4 93 3.7
93
200 5080 119 3032 143 3638 98 2491 5 125 4.9
125
250 6350 149 3789 179 4547 123 3113 6 156 6.1
156
300 7620 179 4547 215 5457 147 3736 7 187 7.4
187
• 16:9 Image on a 4:3 Screen
X1
(a) Screen
Size
(b) Projection Distance minimum maximum
(c) Image
Height
(d) Vertical Offset minimum maximum inch mm inch mm inch mm inch mm inch mm inch mm
30 762 28 704 36 916 14 343 1 34 1 34
60 1524 55 1409 72 1831 27 686 3 69 3 69
70 1778 65 1643 84 2137 32 800 3 80 3 80
80 2032 74 1878 96 2442 36 914 4 91 4 91
90 2286 83 2113 108 2747 41 1029 4 103 4 103
100 2540 92 2348 120 3052 45 1143 5 114 5 114
110 2794 102 2583 132 3357 50 1257 5 126 5 126
120 3048 111 2817 144 3663 54 1372 5 137 5 137
130 3302 120 3052 156 3968 59 1486 6 149 6 149
140 3556 129 3287 168 4273 63 1600 6 160 6 160
150 3810 139 3522 180 4578 68 1715 7 171 7 171
200 5080 185 4696 240 6104 90 2286 9 229 9 229
250 6350 231 5870 300 7630 113 2858 11 286 11 286
300 7620 277 7044 360 9157 135 3429 14 343 14 343
13
X2
(a) Screen
Size
(b) Projection Distance minimum maximum
(c) Image
Height
(d) Vertical Offset minimum maximum inch mm inch mm inch mm inch mm inch mm inch mm
30 762 16 417 20 501 14 343 1 17 1 17
60 1524 33 835 39 1002 27 686 1 34 1 34
70 1778 38 974 46 1169 32 800 2 40 2 40
80 2032 44 1113 53 1336 36 914 2 46 2 46
90 2286 49 1252 59 1503 41 1029 2 51 2 51
100 2540 55 1391 66 1670 45 1143 2 57 2 57
110 2794 60 1530 72 1837 50 1257 2 63 2 63
120 3048 66 1670 79 2003 54 1372 3 69 3 69
130 3302 71 1809 85 2170 59 1486 3 74 3 74
140 3556 77 1948 92 2337 63 1600 3 80 3 80
150 3810 82 2087 99 2504 68 1715 3 86 3 86
200 5080 110 2783 131 3339 90 2286 5 114 5 114
250 6350 137 3478 164 4174 113 2858 6 143 6 143
300 7620 164 4174 197 5009 135 3429 7 171 7 171
NOTE: It is recommended that if you intend to permanently install the projector, please physically test the projection size and distance using the actual projector in situ before you permanently install it.
14
Mounting the Projector
NOTE: If you buy a third-party mount, please use the correct screw size. Screw size can vary depending on the thickness of the mounting plate.
1. To ensure the most secure installation, please use a ViewSonic® wall or ceiling mount.
2. Ensure the screws used to attach a mount to the projector meet the following specifications:
• Screw type: M4 x 8
• Maximum Screw length: 8 mm
138
267.46
NOTE:
• Avoid installing the projector near a heat source.
• Keep at least a 10 cm gap between the ceiling and the bottom of the projector.
15
Preventing Unauthorized Use
The projector has several built-in security features to prevent theft, access, or accidental setting changes.
Using the Security Slot
To help prevent the projector from being stolen, use a security slot locking device to secure the projector to a fixed object.
Below is an example of setting up a security slot locking device:
NOTE: The security slot can also be used as a safety anchor if the projector is mounted to the ceiling.
16
Using the Password Function
To help prevent unauthorized access or use, the projector offers a password security option. The password can be set through the On-Screen Display (OSD)
Menu.
NOTE: Make note of your password, and keep it in a safe place.
Setting a Password
1. Press MENU or to open the OSD Menu and go to: SYSTEM > Security Settings and press ENTER/OK .
2. Highlight Power On Lock and select
On by pressing / .
3. As pictured to the right, the four arrow keys ( , , , ) represent
4 digits (1, 2, 3, 4). Press the arrow keys to enter a six digit password.
5. Confirm the new password by re-entering the new password. Once the password is set, the OSD Menu will return to the Security Settings page.
6. Press EXIT or to leave the OSD Menu.
NOTE: Once set, the correct password must be entered every time the projector is started.
17
Changing the Password
1. Press MENU or to open the OSD Menu and go to: SYSTEM > Security Settings
> Change Password .
2. Press ENTER/OK , the message, ‘INPUT CURRENT PASSWORD’ will appear.
3. Enter the old password.
ͫ If the password is correct, the message, ‘INPUT NEW PASSWORD’ will appear.
ͫ If the password is incorrect, a password error message will appear for 5 seconds followed by the message, ‘INPUT CURRENT PASSWORD’. You can try again or press EXIT or to cancel.
4. Enter a new password.
5. Confirm the new password by re-entering the new password.
6. To leave the OSD Menu, press EXIT or .
NOTE: The digits being input will display as asterisks(*).
Disabling the Password Function
1. Press MENU or to open the OSD Menu and go to: SYSTEM > Security Settings
> Power On Lock .
2. Press / to select Off .
3. The message, “Input Password” will appear. Enter the current password.
ͫ If the password is correct, the OSD Menu returns to the Password page with
“ Off ” shown in the row of Power On Lock .
ͫ If the password is incorrect, a password error message will appear for 5 seconds followed by the message, ‘INPUT CURRENT PASSWORD’. You can try again or press EXIT or to cancel.
NOTE: Please keep the old password, as you will need it to reactivate the password function.
18
Forgetting the Password
If the password function is activated, you will be asked to enter the six-digit password every time you turn on the projector. If you enter the wrong password, the password error message, as pictured to the right, will appear for 5 seconds, and the message ‘INPUT PASSWORD’ follows.
You can retry or if you do not remember, you can use the “Password Recall
Procedure”.
NOTE: If you enter an incorrect password 5 times in succession, the projector will automatically shut down for a short time.
Password Recall Procedure
1. When the message ‘INPUT CURRENT
PASSWORD’ appears, press and hold
ENTER/OK for 3 seconds. The projector will display a coded number on the screen.
2. Write down the number and turn off your projector.
3. Seek help from the local service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector.
19
Locking the Control Keys
With the control keys on the projector locked, you can prevent your settings from being changed accidentally (by children, for example).
NOTE: When the Panel Key Lock is On, no control keys on the projector will operate except Power .
1. Press MENU or to open the OSD Menu and go to: SYSTEM > Panel Key Lock .
2. Press / to select On .
3. Select Yes and press ENTER/OK to confirm.
4. To release panel key lock, press and hold on the projector for 3 seconds.
NOTE: You can also use the remote control to enter the SYSTEM > Panel Key Lock menu and select Off .
20
Making Connections
This section guides you on how to connect the projector with other equipment.
Connecting to Power
1. Connect the power cord to the AC IN jack at the rear of the projector.
2. Plug the power cord into a power outlet.
NOTE: When installing the projector, incorporate a readily accessible disconnect device in the fixed wiring, or connect the power plug to an easily accessible outlet near the unit. If a fault should occur during operation of the projector, use the disconnect device to switch off the power supply, or disconnect the power plug.
21
Connecting to Video/Computer Sources
HDMI Connection
Connect one end of an HDMI cable to the HDMI port of your video/computer device. Then connect the other end of the cable to the HDMI port of your projector.
USB C Connection
Connect one end of an USB C cable to the USB C port of your video/computer device. Then connect the other end of the cable to the USB C port of your projector.
Connecting to Audio
The projector is equipped with speakers, however, you can also connect external speakers to the AUDIO OUT port of the projector.
NOTE:
• The audio output is controlled by the remote control and the projector’s
Volume and Mute settings.
• The AUDIO IN port only works when the input signal is in the DVI-D format.
22
The connection illustrations below are for reference only. The connecting jacks available on the projector vary with each projector model. Some cables may not be included with the projector. They are commercially available from electronics stores.
AUDIO IN
AUDIO OUT
RS232
SERVICE HDMI 1
HDCP 2.2
HDMI 2
HDCP 2.2
USB C
USB A
5V/1A
23
Operation
Turning the Projector On/Off
Starting Up the Projector
1. Press the Power button to turn on the projector.
2. The light source will light up, and a “Power On/Off Ring Tone” will play.
3. The Power Indicator Light stays green when the projector is On.
NOTE:
• If the projector is still hot from previous use, it will run the cooling fan for 90 seconds before activating the light source.
• To maintain light source life, once you turn the projector On, wait at least five (5) minutes before turning it off.
4. Turn on all of the connected equipment, i.e. notebook, and the projector will start to search for an input source.
NOTE: If the projector detects an input source, the Source Selection Bar will appear. If an input source is not detected, the message, ‘No Signal’ will appear.
First Time Activation
If the projector is activated for the first time, select the projector position, WiFi settings and OSD language following the on-screen instructions.
24
Shutting Down the Projector
1. Press the Power or Off button and a confirmation message will appear to prompt you to press the Power or Off button a second time. Additionally you can press any other button to cancel.
NOTE: If you do not respond in a few seconds after the first press, the message will disappear.
2. Once the cooling process finishes, a “Power On/Off Ring Tone” will play.
3. Disconnect the power cord from the power outlet if the projector will not be used for an extended period of time.
NOTE:
• To protect the light source, the projector will not respond to commands during the cooling process.
• Do not unplug the power cord before the projector completely shuts down.
25
Selecting an Input Source
The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time.
If you want the projector to automatically search for the input source, ensure the
Quick Auto Search function in the SYSTEM menu is On .
NOTE: If no input source is detected, the projector will go to SMART SYSTEM .
To manually select the input source do the following:
1. Press SOURCE or , and a source selection menu will appear.
2. Press / until your desired signal is selected and press ENTER/OK .
3. Once detected, the selected source information will be displayed on the screen for a few seconds.
NOTE: If there are multiple devices connected to the projector, repeat steps 1-2 to search for another source.
26
Adjusting the Projected Image
Adjusting the Projector's Height and Projection Angle
The projector is equipped with one (1) adjuster foot. Adjusting the foot will change the projector’s height and the vertical projection angle. Carefully adjust the foot to fine tune the projected image’s position.
Fine-Tuning the Image Size and Clarity
To adjust the projected image to the size that you need, rotate the Zoom Ring.
To improve the clarity of the image, rotate the Focus Ring.
27
Correcting Keystone
Keystoning refers to the situation where the projected image becomes a trapezoid due to angled projection.
To correct this, besides adjusting the height of the projector, you may also:
1. Use the Left/ Right/ Up/ Down keys on the projector or remote control to display the keystone page (when the input source is not SMART SYSTEM ).
2. After the keystone page is displayed, press Down to correct keystoning at the top of the image. Press Up to correct keystoning at the bottom of the image. Press to correct keystoning at the bottom of the image. Press
Right to correct keystoning at the right side of the image. Press Left to correct keystoning at the left side of the image.
MENU
EXIT
SOURCE
?
ENTER
BLANK
COLOR
MODE
28
Adjusting 4 corners
You can manually adjusts the shape and size of an image that is unevenly rectangular on all sides.
1. To display the Corner Adj.
page, you can do one of the followings:
• Press ENTER/OK .
• Open the OSD menu and go to the
DISPLAY > Corner Adj.
menu and press
Enter . The Corner Adj.
page is displayed.
2. Use / / / to select the corner you wish to adjust and press ENTER/OK .
3. Use / to select an adjustment method that suits your need and press ENTER/OK .
Indicates the corner you seleted.
4. As indicated on the screen ( / for a 45-degree angle adjustment and / / / for a 90-degree angle adjustment), press / / / to adjust its shape and size. You can press Exit or to go back to a previous step. A long press for 2 seconds on
ENTER/OK you chose.
will reset the settings on the corner that
NOTE:
• Adjusting keystone will reset the Corner Adj.
settings.
• After the Corner Adj.
settings have been modified, some aspect ratios or timings are not available. When that happens, reset the settings on all 4 corners.
Hiding the Image
In order to draw the audience’s full attention to the presenter, you can press
BLANK on the projector to hide the screen image. Press any key on the projector or remote control to restore the image.
CAUTION: Do not block the projection lens as this could cause the blocking object to become heated and deformed or even cause a fire.
29
Menu Functions
This section will introduce the On-Screen Display (OSD) Menu and its options.
General On-Screen Display (OSD) Menu Operation
NOTE: The OSD screenshots in this manual are for reference only and may differ from the actual design. Some of the following OSD settings may not be available.
Please refer to the actual OSD of your projector.
The projector is equipped with an On-Screen Display (OSD) Menu for making various adjustments. It can be accessed by pressing MENU or on the projector or remote control.
1. Press / to select a main menu. Then press ENTER/OK or use / to access the sub-menu list.
2. Press / to select the menu option. Then press ENTER/OK to display its submenu, or press / to adjust/select the setting.
NOTE: Some sub-menu options may have another sub-menu. To enter the respective sub-menu, press ENTER/OK . Use / or / to adjust/select the setting.
30
On-Screen Display (OSD) Menu Tree
Main Menu
DISPLAY
Sub-menu
Aspect Ratio
Menu Option
Auto
4:3
Keystone
Corner Adj.
Zoom
OverScan
3X Fast Input
16:9
16:10
2.35:1
Native
Auto V Keystone
Vertical
Horizontal
Top-Right
Top-Left
Bottom-Right
Bottom-Left
0.8X ~2.0X
Off/1/2/3/4/5
Inactive
Active
Off/On
+40~-40
+40~-40
31
Main Menu
IMAGE
Sub-menu
Color Mode
Brightness
Contrast
Color Temp.
Advanced
Menu Option
Brightest
TV
Gaming
Movie
User 1
User 2
0~100
-50~50
9300K/7500K/6500K
Red Gain
Green Gain
Blue Gain
Red Offset
Green Offset
Blue Offset
Color
Sharpness
Gamma
Color Management
0~100
0~100
0~100
-50~+50
-50~+50
-50~+50
-50~50
0~31
1.8/2.0/2.2/2.35/
2.5/Cubic/sRGB
Primary Color
Hue
Saturation
Gain
Reset Color Settings Reset
Cancel
32
Main Menu
POWER
MANAGEMENT
BASIC
Sub-menu
Auto Power On
Smart Energy
Menu Option
Signal
CEC
Direct Power On
Auto Power Off
Disable/HDMI
Disable/Enable
Disable/Enable
Disable/10 min/20 min/30 min
Standby Settings
Audio Settings
Sleep Timer
Power Saving
Audio Pass Through
Audio Mode
Mute
Audio Volume
Disable/30 min/1 hr/2hr/3 hr/4 hr/ 8 hr/12 hr
Disable/Enable
Off/On
Music/Speech/Movie
Off/On
0~20
Power On/Off Ring Tone Off/On
Presentation Timer Timer Period 1~240 m
Timer Display
Timer Position
Always/1 min/2 min/3 min/Never
Top-Left/Bottom-Left/
Top-Right/Bottom-Right
Pattern
Blank Timer
Message
Splash Screen
Timer Counting Direction Count Down/Count Up
Sound Reminder
Start Counting/Off
Off/On
Off
Test Card
Disable/5 min/10 min/15 min/20 min/25 min/30 min
Off
On
Black
Blue
ViewSonic
33
Main Menu
ADVANCED
Sub-menu
HDR
3D Settings
Menu Option
HDR
EOTF
3D Format
Auto/SDR
Low/Mid/High
Auto
Off
Frame Sequential
Frame Packing
Top-Bottom
HDMI Settings
3D Sync Invert
Save 3D Settings
HDMI Format
HDMI Range
Light Source Settings Light Source Mode
Side-by-Side
Disable/Invert
Yes/No
Auto/RGB/YUV
Auto/Enhanced/
Normal
Normal/Eco/
Dynamic Black 1/
Dynamic Black 2/Custom
20%~100% Light Source Power
Reset Light Source Hours Reset/Cancel
Light Source Hours Information Light Source Usage Time
Normal
Eco
Dynamic Black 1
Dynamic Black 2
Custom
Restart Smart System Reset
Reset Settings
Cancel
Reset
Cancel
34
Main Menu
SYSTEM
Sub-menu
Language
Menu Option
Multi-Language OSD Selection
Projector Position Front Table
Rear Table
Menu Settings
Rear Ceiling
Front Ceiling
Menu Display Time
Menu Position
5 sec/10 sec/15 sec/20 sec/25 sec/30 sec
Center/Top-Left/
Top-Right/
Bottom-Left/
Bottom-Right
High Altitude Mode Off
On
Quick Auto Search Off
Security Settings
Panel Key Lock
Control Method
Baud Rate
On
Change Password
Power On Lock
Off
On
Off/On
RS-232
USB
2400/4800/9600/14400/19200/
38400/57600/115200
INFORMATION Source
Color Mode
Resolution
Color System
Firmware Version
3X Fast Input
S/N
35
DISPLAY Menu
1. Press the MENU or button to display the On-Screen Display (OSD) Menu.
2. Press / to select the DISPLAY menu. Then press ENTER/OK or use / to access the DISPLAY menu.
3. Press / to select the menu option. Then press ENTER/OK to display its submenu, or press / to adjust/select the setting.
NOTE: Some sub-menu options may have another sub-menu. To enter the respective sub-menu, press ENTER/OK . Use / or / to adjust/select the setting.
36
Menu Option
Aspect Ratio
Keystone
Corner Adj.
Zoom
OverScan
Description
Auto
Scales an image proportionally to fit the projector’s native resolution in its horizontal width. This is suitable for the incoming image which is neither in 4:3 nor 16:9 and you want to make most use of the screen without altering the image’s aspect ratio.
4:3
Scales an image so that it is displayed in the center of the screen with a 4:3 aspect ratio. This is most suitable for 4:3 images like computer monitors, standard definition TV, and
4:3 aspect DVD movies, as it displays them without aspect alteration.
16:9
Scales an image so that it is displayed in the center of the screen with a 16:9 aspect ratio. This is most suitable for images which are already in a 16:9 aspect, like high definition TV, as it displays them without aspect alteration.
16:10
Scales an image so that it is displayed in the center of the screen with a 16:10 aspect ratio. This is most suitable for images which are already in a 16:10 aspect, as it displays them without aspect alteration.
2.35:1
Scales an image so that it is displayed in the center of the screen with a 2.35:1 aspect ratio without aspect alteration.
Native
Projects an image as its original resolution and resizes it to fit within the display area. For input signals with lower resolutions, the projected image will be displayed in its original size.
Adjusts the keystoning situation where the projected image becomes a trapezoid due to angled projection.
Adjusts the shape and size of an image that is unevenly rectangular on all sides.
Magnifies the projected image and allows you to navigate the image.
Adjusts the overscan rate from 0 to 5.
37
Menu Option
3X Fast Input
Description
This function is favorable to frame rate reducing. Quick response time in native timing can be achieved. When enabled, the following settings (if applicable) will return to factory preset values: Aspect Ratio, Zoom, OverScan.
NOTE: This function is only available when a native timing input signal is selected.
38
IMAGE Menu
1. Press the MENU or button to display the On-Screen Display (OSD) Menu.
2. Press / to select the IMAGE menu. Then press ENTER/OK or use / to access the IMAGE menu.
3. Press / to select the menu option. Then press ENTER/OK to display its submenu, or press / to adjust/select the setting.
NOTE: Some sub-menu options may have another sub-menu. To enter the respective sub-menu, press ENTER/OK . Use / or / to adjust/select the setting.
39
Menu Option
Color Mode
Brightness
Contrast
Color Temp.
Description
Brightest
Maximizes the brightness of the projected image. This mode is suitable for environments where extra-high brightness is required, such as using the projector in well lit rooms.
TV
Optimized for viewing sports in well-lit environments.
Gaming
Suitable for playing video games in a bright living room.
Movie
For playing colorful movies, video clips from digital cameras or
DVs through the PC input for best viewing in a blackened (little light) environment.
User 1/User 2
Recalls the customized settings. After User 1/User 2 is selected, some of the sub-menus under the IMAGE menu can be adjusted, according to your selected input source.
The higher the value, the brighter the image. Adjust this option so the black areas of the image appear just as black and details in the dark area are more visible.
Use this to set the peak white level after you have previously adjusted the Brightness setting.
There are several preset color temperature settings (9300K,
7500K, 6500K) available. The available settings may vary according to the personal preferences.
To set a custom color temperature, you can further adjust the following items:
Red Gain/Green Gain/Blue Gain
Adjusts the Contrast levels of Red, Green, and Blue.
Red Offset/Green Offset/Blue Offset
Adjusts the Brightness levels of Red, Green, and Blue.
40
Menu Option Description
Advanced Color
A lower setting produces less saturated colors. If the setting is too high, colors will be overpowering and may appear unrealistic.
Sharpness
A higher value will sharpen the image, while a lower value will soften the image.
Gamma
Gamma refers to the brightness level of the projector’s grayscale levels.
Color Management
Only in permanent installations with controlled lighting levels such as boardrooms, lecture theaters, or home theaters, should color management be considered. Color management provides fine color control adjustment to allow for more accurate color reproduction. Select Primary Color first and adjust its range/values in Hue, Saturation and Gain.
Reset Color Settings Returns current image settings to the factory preset values.
41
POWER MANAGEMENT Menu
1. Press the MENU or button to display the On-Screen Display (OSD) Menu.
2. Press / to select the POWER MANAGEMENT menu. Then press ENTER/OK or use / to access the POWER MANAGEMENT menu.
3. Press / to select the menu option. Then press ENTER/OK to display its submenu, or press / to adjust/select the setting.
NOTE: Some sub-menu options may have another sub-menu. To enter the respective sub-menu, press ENTER/OK . Use / or / to adjust/select the setting.
42
Menu Option
Auto Power On
Smart Energy
Description
Signal
Selecting HDMI allows the projector to turn on automatically once the HDMI/USB C signal is fed through the HDMI/USB C cable.
CEC
This projector supports CEC (Consumer Electronics Control) function for synchronized power on/off operation via HDMI connection. That is, if a device that also supports CEC function is connected to the HDMI input of the projector, when the projector’s power is turned off, the power of the connected device will also be turned off automatically. When the power of the connected device is turned on, the projector’s power will be turned on automatically.
NOTE:
• In order for the CEC function to work properly, make sure that the device is correctly connected to the HDMI input of the projector via an HDMI cable, and its CEC function is turned on.
• Depending on the connected device, the CEC function may not work.
Direct Power On
Allows the projector to turn on automatically once power is fed through the power cord.
Auto Power Off
Allows the projector to turn off automatically after a set period of time once no input source is detected to prevent unnecessary waste of light source life.
Sleep Timer
Allows the projector to turn off automatically after a set period of time to prevent unnecessary waste of light source life.
Power Saving
Lowers power consumption if no input source is detected.
When Enable is selected, the projector light source mode will change to Eco mode after no signal is detected for five (5) minutes. This will also help prevent any unnecessary waste of light source life.
43
Menu Option
Standby Settings
Description
The functions below are available in standby mode (plugged in, but not turned on).
Audio Pass Through
When selecting On , the projector outputs an audio signal when the Audio In and Audio Out sockets are correctly connected to a proper device.
44
BASIC Menu
1. Press the MENU or button to display the On-Screen Display (OSD) Menu.
2. Press / to select the BASIC menu. Then press ENTER/OK or use / to access the BASIC menu.
3. Press / to select the menu option. Then press ENTER/OK to display its submenu, or press / to adjust/select the setting.
NOTE: Some sub-menu options may have another sub-menu. To enter the respective sub-menu, press ENTER/OK . Use / or / to adjust/select the setting.
45
Menu Option Description
Audio Settings Audio Mode
Select a prefereed audio mode to suit your audio content.
Mute
Select On to temporarily turn off the projector’s internal speaker or the volume being output from the audio output jack.
Audio Volume
Adjusts the volume level of the projector’s internal speaker or the volume being output from the audio output jack.
Power On/Off Ring Tone
Turns on/off the ring tone during the starting up and shutting down process.
Presentation Timer Presentation timer can indicate the presentation time on the screen to help you achieve better time management when giving presentations.
Timer Period
Sets the time period. If the timer is already on, the timer will restart whenever the Timer Period is reset.
Timer Display
Allows you to decide if you want the timer to show up on the screen for one of the following time periods:
ͫ Always: Displays the timer on screen throughout the presentation time.
ͫ 1 min/2 min/3 min: Displays the timer on screen in the last 1/2/3 minute(s).
ͫ Never: Hides the timer throughout the presentation time.
Timer Position
Sets the timer position.
Timer Counting Direction
Sets your desired counting direction between:
ͫ Count Down: Decreases from the preset time to 0.
ͫ Count Up: Increases from 0 to the preset time.
Sound Reminder
Allows you to decide if you want to activate a sound reminder.
Once enabled, a double beep sound will be heard at the last 30 seconds of counting down/up, and a triple beep sound will be produced when the timer is up.
Start Counting/Off
Select Start Counting to activate the timer. Select Off to cancel it.
46
Menu Option
Pattern
Blank Timer
Message
Splash Screen
Description
Helps adjust the image size and focus, and checks for distortion in the projected image.
Allows the projector to return the image automatically after a period of time when there is no action taken on the blank screen. To display the blank screen, press Blank on the projector or remote control.
NOTE: Do not block the projection lens as this could cause the blocking object to become heated and deformed or even cause a fire.
Sets reminder messages On or Off.
Selects which logo screen will appear during projector start-up.
47
ADVANCED Menu
1. Press the MENU or button to display the On-Screen Display (OSD) Menu.
2. Press / to select the ADVANCED menu. Then press ENTER/OK or use / to access the ADVANCED menu.
3. Press / to select the menu option. Then press ENTER/OK to display its submenu, or press / to adjust/select the setting.
NOTE: Some sub-menu options may have another sub-menu. To enter the respective sub-menu, press ENTER/OK . Use / or / to adjust/select the setting.
48
Menu Option
HDR
3D Settings
Description
HDR
The projector supports HDR imaging sources. It can automatically detect the dynamic range of the source, and optimize image gamma and color settings to reproduce contents under wide range of light conditions. You also select
SDR.
EOTF
The projector can automatically adjust the brightness levels of your image according to the input source. Normally, the default setting “Mid” is recommended. If the brightness of the projected image is dark, please use “Low”. When giving priority to gradation property, please use “High”.
This projector features a 3D function which enables you to enjoy 3D movies, videos, and sporting events in a more realistic way by presenting the depth of the images. You need to wear a pair of 3D glasses to view 3D images.
3D Format
The default setting is Auto and the projector automatically chooses an appropriate 3D format when detecting 3D contents. If the projector cannot recognize the 3D format, choose a 3D mode.
3D Sync Invert
When you discover the inversion of the image depth, enable this function to correct the problem.
Save 3D Settings
Saves current 3D settings. 3D settings will automatically be applied if the same resolution and input source are selected.
NOTE: When the 3D Sync function is on:
• The brightness level of the projected image will decrease.
• The Color Mode, Light Source Mode, Zoom, and OverScan cannot be adjusted.
49
Menu Option
HDMI Settings
Description
HDMI Format
Select a suitable color space according to the color space setting of the output device connected.
ͫ Auto: Sets the projector to detect the color space setting of the input signal automatically.
ͫ RGB: Sets the color space as RGB.
ͫ YUV: Sets the color space as YUV.
HDMI Range
Select a suitable HDMI color range according to the color range setting of the output device connected.
ͫ Auto: Sets the projector to detect the HDMI range of the input signal automatically.
ͫ Enhanced: Sets the HDMI color range as 0 - 255.
ͫ Normal: Sets the HDMI color range as 16 - 235.
Light Source Settings Light Source Mode
ͫ Normal: Provides full light source brightness.
ͫ Eco: Reduces light source power consumption by 20% and lowers brightness to extend the light source life and decreases the fan noise.
ͫ Dynamic Black 1: Reduces light source power consumption by up to 70% depending on the content brightness level.
ͫ Dynamic Black 2 : Reduces light source power consumption by up to 50% depending on the content brightness level.
ͫ Custom: Allows you to adjust the light source power.
Light Source Power
Only available when Light Source Mode is Custom .
Reset Light Source Hours
Resets the light source timer after a new light source is installed. For changing the light source, please contact qualified service personnel.
Light Source Hours Information
ͫ Light Source Usage Time: Displays the number of hours the light source has been used.
Restart Smart System Restarts the Smart System immediately after selecting Reset.
50
Menu Option
Reset Settings
Description
Returns all settings to the factory preset values. When using
Reset Settings, the following settings will still remain: Zoom,
Keystone, Language, Projector Position, High Altitude Mode,
Security Settings, Control Method, and Baud Rate.
51
SYSTEM Menu
1. Press the MENU or button to display the On-Screen Display (OSD) Menu.
2. Press / to select the SYSTEM menu. Then press ENTER/OK or use / to access the SYSTEM menu.
3. Press / to select the menu option. Then press ENTER/OK to display its submenu, or press / to adjust/select the setting.
NOTE: Some sub-menu options may have another sub-menu. To enter the respective sub-menu, press ENTER/OK . Use / or / to adjust/select the setting.
52
Menu Option Description
Language
Projector Position
Menu Settings
Sets the language for the On-Screen Display (OSD) Menu.
Selects a proper position for the projector.
Menu Display Time
Sets the length of time the OSD Menu will remain active after your last interaction.
Menu Position
Sets the OSD Menu’s position.
High Altitude Mode We recommend you use the High Altitude Mode when your environment is between 1,500 m to 3,000 m above sea level, and ambient temperature is between 0°C–30°C.
NOTE:
• Do not use High Altitude Mode if your environment is between 0 to 1,499 m, and the temperature is between
0°C to 35°C. If used, the projector will become over cooled.
• Using “High Altitude Mode” may cause more operating noise, as the fan speed will be increased to improve cooling and performance.
Quick Auto Search Allows the projector to automatically search for the signals.
Security Settings See “Using the Password Function” on page 17.
Panel Key Lock
Control Method
Locks the control keys on the projector.
Allows you to select a preferred control port: through the RS-
232 port or the USB port (Service).
Baud Rate Selects a baud rate that is identical with your computer’s so that you can connect the projector using a suitable RS-232 cable and control the projector with RS-232 commands
53
INFORMATION Menu
1. Press the MENU or button to display the On-Screen Display (OSD) Menu.
2. Press / to select the INFORMATION menu and display its contents.
Menu Option
Source
Color Mode
Resolution
Color System
Firmware Version
3X Fast Input
S/N
Description
Shows the current input source.
Shows the selected mode in the IMAGE menu.
Shows the native resolution of the input source.
Shows input system format.
Shows the current firmware version.
Shows whether the function is activated or not.
Shows the serial number for this projector.
54
Smart System
This section will introduce the SMART SYSTEM .
Home Screen
NOTE: The screenshots in this manual are for reference only and may differ from the actual design. Some of the following settings may not be available. Please refer to the actual design of your projector.
The Home Screen is displayed when the input source is SMART SYSTEM.
To navigate the Home Screen, simply use the directional buttons. You can return to the main Home Screen at any time by pressing on the remote control, regardless of what page you are on.
1. Press / to select a main menu. Then press ENTER/OK or use press to access the sub-menu list.
2. Press / / / to select the menu option. Then press ENTER/OK to display its sub-menu, or press / to adjust/select the setting.
NOTE: Some sub-menu options may have another sub-menu. To enter the respective sub-menu, press ENTER/OK . Use / or / to adjust/select the setting.
55
Menu Operations
Player
The projector automatically scans the video files in the external storage device.
When you click Player , the scanned video can be played in a loop.
Some functions are available when Player is highlighted. Press and then use /
to select.
• Bluetooth
The projector is equipped with Bluetooth that allows the user to connect their device wirelessly for audio playback.
To connect and pair your device:
1. Go to: Home Screen > Bluetooth.
2. Use the / to select Bluetooth Speaker or Bluetooth Pairing . Then press
ENTER/OK .
3. A dialogue box appears, select Connect and press ENTER/OK to enter
Bluetooth mode.
4. A sound effect will be audible upon entering pairing mode.
5. Upon successful connection, another sound effect will be audible.
NOTE: The projector’s name will be labeled as “ViewSonic Projector”. Once paired, if both the projector and your device are powered on they will automatically connect via Bluetooth in Bluetooth Speaker mode. When connected please note that only the Power, Exit and the buttons can exit Bluetooth mode.
6. The projector will search for nearby Bluetooth devices. Select your device from the list and press ENTER/OK .
56
You can also connect the projector to external headphones or speakers that support Bluetooth:
1. Go to: Home Screen > Bluetooth.
2. Use the / to select Bluetooth Out . Then press ENTER/OK .
NOTE: Once paired, if both the projector and your device are powered on they will automatically connect via Bluetooth.
• Screen Mirroring
Screen Mirroring provides a 5GHz Wi-Fi connection for users to mirror the screen on their personal device.
NOTE: Ensure your device is connected to the same network as the projector.
57
For iOS:
1. Access the drop down control menu.
2. Select the “Screen Mirroring” icon.
3. Choose “ViewSonic PJ-XXXX”.
For Android:
1. Download and install the “Google Home” application and open it.
2. Pull-to-refresh the app and wait for 30 seconds.
3. “ViewSonic PJ-XXXX” will now be visible, select it.
NOTE: Some Android devices support direct “Casting”. If your device does, go to the Casting feature and choose “ViewSonic PJ-XXX” from the list of available devices. You can also scan the FAQ QR code and follow the steps to directly cast your Android device.
• FileBrowser
You can browse your files here.
• Source
Displays the input source selection bar. You can switch the input source .
My Apps
Displays your favorite Apps.
To remove an application from My Apps page:
1. After entering the My Apps page, all your favorite applications are displayed.
2. Long press on the selected APP to remove it.
58
3. Once removed, below dialogue box will appear.
Application
Access and view all the applications you have installed.
To add an application to My Apps page or uninstall it:
1. After entering the Application page, all your applications are displayed.
2. Long press on the selected APP to add to My Apps page or uninstalled it.
59
3. Once succeeded, below dialogue box will appear and the application will be displayed with an asterisk.
Applications that have been added to My Apps page will be displayed under My Apps page from the homepage.
To install an application:
1. Go to Application > App Store from homepage.
2. Use the directional buttons to navigate the menu options. When you find your preferred application, press OK to enter the details and select the INSTALL button to install it.
3. A progress bar will display while downloading.
4. After the application is installed, you can open, upgrade or uninstall the application.
NOTE:
• You can install third-party applications by .apk file in File Management. However, some third-party applications may have compatibility issues.
• Applications not preloaded may not be compatible or work properly.
• Some of the applications (including preloaded and manually installed applications)
60
may require a keyboard or mouse to use.
• Some applicaitons may be region-specific.
Wallpaper
Use / to select a wallpaper and press ENTER/OK to set it as the wallpaper on the
Home Screen.
Media control bar buttons
The media control bar buttons will appear on screen if a video or music file is played.
Video Music
Back Previous
Rewind Play
Play
Pause
Fast forward
Pause
Next
Next
Previous
3D
More
NOTE: When using a USB storage device, note the following:
ͫ Some USB storage devices may not be compatible.
ͫ If you are suing a USB extension cable, the USB device may not be recongnized.
ͫ You may experience longer loading time when handling larger files.
ͫ Data on the USB storage device may be damaged or lost. Back up important files beforehand.
Supported file formats
Multimedia formats
Extension
.xvid
.avi
.mp4
.m4v
.mov
Type
Video
Audio
Video
Codec
Xvid, H.264
MP3
H.264/MPEG-4
61
Extension
.mkv
.ts
.trp
.tp
.mts
.m2ts
Type
Video
Video
Audio
Codec
H.264
H.264, MPEG-2
MP3
.vob
.mpg
Office formats
Audio
Video
Audio
MPEG-1, MPEG-2
DVD-LPCM
MPEG-1
Document viewing function
Items doc/docx xls/xlsx ppt/pptx
Indicators
Able to open and read documents in doc/docx
Able to open and read documents in xls/xlsx
Able to open and read documents in ppt/pptx
Able to open and read documents in PDF
Photo formats
Format
.jpg/.jpeg
.bmp
.png/.gif
Type
Progressive JPEG
Baseline JPEG
Comment
Max. resolution: 1024 x 768
Max. resolution: 15360 x 8640
Max. resolution: 9600 x 6400
Max. resolution: 5120 x 2880
Supported external connected device formats
Device
NTFS format FAT32 format exFAT
Read Write Read Write Read Write
USB memory stick
USB HDD -
NOTE:
• Windows 10 built-in format tool only supports FAT32 format up to 32GB.
• Only FAT32 format is supported for firmware upgrade.
Firmware upgrade
You can update the firmware online, or by USB device and check the version number.
NOTE: Do not unplug the power cord, USB device or disconnect from the Internet during the upgrade process.
62
1. Make sure that the projector is connected to the Internet.
2. Go to Application > UPDATE from homepage.
Firmware update online
1. Go to Application > UPDATE > Online update .
NOTE: Auto download is enabled by default for online upgrade. When enabled, if the system detects a newer version, it will automatically download the software in the background.
2. Select Online update and press ENTER/OK.
3. The system will check the ViewSonic website (OTA) and display below dialog message if there is a newer firmware.
4. After selecting Download , a progress bar will appear as the download process begins.
63
5. Upon reaching 100%, the following message will appear. Select Update Right
Now .
6. The Strat OTA update dialog message will appear.
7. Select Update and the projector will restart the screen will turn black for a few minutes. The update process takes about 5 to 10 minutes. When finished, it will take a few minutes to restart the projector.
64
Firmware update via a USB device
1. Download the latest firmware version form the ViewSonic website and copy the file to a USB device.
2. Plug the USB device into the projector.
3. Go to Application > UPDATE > UpdateLocale .
4. Click Select and press ENTER/OK .
5. The system will detect the firmware and display the following information. Select the firmware file.
6. The selected firmware will show up. Click Update .
7. The Local update dialog message is displayed, select Update .
65
8. Select Update and the projector will restart the screen will turn black for a few minutes. The update process takes about 5 to 10 minutes. When finished, it will take a few minutes to restart the projector.
66
System related settings
More settings are available on the bottom list of the Home Screen.
Settings
NOTE: Some functions may not be supported. The settings will be grayed out and cannot be operated.
Menu Option Description
Network & internet
Wi-Fi
Portable hotspot
VPN
Prvate DNS
Apps & notifications
Storage
Security & location
Device storage
Device admin apps
Sets the Wifi settings and AP hotspot.
You can browse the Apps, set App permissions and notifications.
You can check the storage status here.
67
Menu Option
System About device
Languages
& input
Date & time
Reset options
Update
IP address
Wi-Fi MAC address
Bluetooth address
Build number
Languages
Virtual keyboard
Physical keyboard
Automatic date&time
Set Date
Set Time
Set time zone
Automatic 24hour format
Use 24-hour format
Displays the Bluetooth address.
Displays the version number of the system.
You can set the language and input method here.
The projector automatically synchronize with an internet time server.
Available when Autmatic date&time is disabled. You can set the date/time/ time zone.
Shows the time in the 24-hour format
Available when Autmatic 24-hour format is disabled. When disabled, the projector shows the time in the 12hour format.
You can reset the network settings,
App preferences or erase all data here.
Reset Wi-
Fi mobile
&Buletooth
Reset app preferences
Erase all data
(factory reset)
Online update
Description
Displays the IP address of the projector.
DIsplays the Wi-Fi MAC address.
UpdateLocale
Ensure that the projector is connected to the Internet.
Download new firmware file in the
USB device and connect it to the USB A port.
68
Network
Directly goes to the Wi-Fi page in the Settings .
Storage cleaner
Click this item to delete the log and apk files in the local storage and release the local storage space.
Accelerator
Click this item to terminate the processes that are not system’s. This operation can be performed when there are many APPs running in the back ground and the system response speed is slow.
69
Appendix
Specifications
Item
Projector
Input signal
Category
Type 0.65” LED
X1
Specifications
X2
Display Size
Throw Ratio
30”~300”
1.15~1.5
(95”±3%@2.43m)
Lens
Optical Zoom
F = 2.59 – 2.87
1.3x
Light Source Type RGB LED
Display System 1-CHIP DMD
HDMI
0.69~0.83
(95”±3%@1.44m)
F = 2.60 – 2.78
1.2x
f h
: 15K~129KHz, f v
:23~120Hz,
Pixel rate: 170MHz
Resolution Native
Power adapter 1 Input Voltage
Operating conditions
Temperature
Storage conditions
Dimensions
1920 x 1080
AC 100-240V, 50/60 Hz (auto switch)
0°C to 40°C (32°F to 104°F)
Humidity
Altitude
Temperature
Humidity
0% to 90% (non-condensing)
0 to 1,499 m at 0°C to 35°C
1,500 to 3,000 m at 0°C to 30°C
-20°C to 60°C (non-condensing)
0% to 90% (non-condensing)
Altitude 0 to 12,200 m at 30°C
Physical (W x H x D) 355 x 121 x 244 mm
(14” x 4.8” x 9.6”)
355 x 121 x 251 mm
(14” x 4.8” x 9.9”)
Weight
Power consumption
Physical
On 2
Off
3.6 kg (7.94 lb)
218 W (Typical)
< 0.5W (Standby)
1 Please use the power adapter from ViewSonic® or an authorized source only.
2 The test condition follows EEI standards.
70
Projector Dimensions
X1
MENU
EXIT
SOURCE
?
ENTER
BLANK
COLOR
MODE
244 mm
355 mm
121 mm
X2
MENU
EXIT
SOURCE
?
ENTER
BLANK
COLOR
MODE
251 mm
Timing Chart
Signal
VGA
SVGA
XGA
WXGA
Quad-VGA
SXGA
SXGA+
WXGA+
WSXGA+
HDMI / USB-C
Resolution (dots)
640 x 480
Aspect ratio
04:03
800 x 600
1024 x 768
1152 x 864
1280 x 768
1280 x 800
1360 x 768
1366 x 768
1280 x 960
1280 x 1024
1400 x 1050
1440 x 900
1680 x 1050
04:03
04:03
04:03
15:09
16:10
16:09
16:09
04:03
05:04
04:03
16:10
16:10
71
Refresh rate (Hz)
60/70/75/85/120
60/70/75/85/120
60/70/75/85/120
75
60
60/75/85
60
60
60/85
60/75/85
60
60
60
Signal
UXGA
WUXGA
MAC 13"
MAC 16"
MAC 19"
MAC 21"
HDTV (1080p)
HDTV (1080i)
HDTV (720p)
SDTV (480p)
SDTV (576p)
SDTV (480i)
SDTV (576i)
4k/24P
4k/25P
4k/30P
4k/50P
4k/60P
Signal
1080p
720p
1080i
1080p
720p
Signal
Signal
SVGA
XGA
HDMI / USB-C
Resolution (dots) Aspect ratio
1600 x 1200
1920 x 1200
04:03
16:10
640 x 480
832 x 624
1024 x 768
1152 x 870
1920 x 1080
1920 x 1080
1280 x 720
720 x 480
720 x 576
720 x 480
720 x 576
3840 x 2160
3840 x 2160
3840 x 2160
3840 x 2160
3840 x 2160
04:03
04:03
04:03
04:03
16:09
16:09
16:09
4:3 / 16:9
4:3 / 16:9
4:3 / 16:9
4:3 / 16:9
16:09
16:09
16:09
16:09
16:09
HDMI 3D
Resolution (dots) Aspect ratio
In Frame Packing format
1920 x 1080 16:09
1280 x 720 16:09
In Side-by-Side format
1920 x 1080 16:09
In Top-Bottom format
1920 x 1080 16:09
1280 x 720 16:09
3D (HDMI signal included)
Resolution (dots) Aspect ratio
Resolution (dots)
800 x 600
Aspect Ratio
04:03
1024 x 768 04:03
72
Refresh rate (Hz)
60
60
67
75
75
75
50 / 60
50 / 60
50 / 60
60
50
30
50
60
60
50
24
25
Refresh rate (Hz)
23.98/24
50/59.94/60
50/59.94/60
23.98/24
50/59.94/60
Refresh rate (Hz)
Refresh Rate (Hz)
60* / 120**
60* / 120**
Signal
HD
WXGA
HDTV (1080p)
3D (HDMI signal included)
Resolution (dots) Aspect ratio
1280 x 720
1280 x 800
16:09
16:09
1920 x 1080 for Video Signal
16:09
Refresh rate (Hz)
60* / 120**
60* / 120**
60
SDTV (480i)***
NOTE:
720 x 480 4:3 / 16:9 60
*60Hz signals are supported for Side-by-Side, Top-Bottom, and
Frame Sequential formats.
**120 Hz signals are supported for Frame Sequential format only.
***Video signal (SDTV 480i) is supported for Frame Sequential format only.
73
Troubleshooting
Common Problems
This section describes some common problems that you may experience when using the projector.
Problem Possible Solutions
The projector does not turn on • Ensure the power cord is properly attached to the projector and to the power outlet.
There is no picture
• If the cooling process has not completed, please wait until it has finished then try to turn on the projector again.
• If the above does not work, try another power outlet or another electrical device with the same power outlet.
• Ensure the video source cable is connected properly, and that the video source is turned on.
• If the input source is not selected automatically, select the correct source with the Source key on either the projector or the remote control.
The image is blurred
The remote control does not work
The image abnormal
Bluetooth connection fails
• Adjusting the Focus Ring will help correctly focus the projection lens.
• Ensure the projector and screen are aligned properly.
If necessary, adjust the height of the projector as well as the projection angle and direction.
• Ensure there are no obstacles between the remote control and projector; and that they are within 8 m
(26 ft) of each other.
• The batteries may be out of power, please check and replace if necessary.
• Ensure the video source cable is connected properly, and that the video source is turned on.
• If the above does not work, check the air intake or exhaust not block.
• Perform Reset Wi-Fi mobile &Buletooth in the
Settings > System > Reset options menu when the input source is SMART SYSTEM.
74
LED Indicator
Light
Orange
Green Flashing
Status and Description
Stand-by mode
Powering up
Green
Red
Normal operation
Downloading
Orange Flashing
Red Flashing once per second
Burn in off
Fan error
Red Flashing once per 3 seconds Thermal and temperature error
Green & Red Flashing alternately Light source error
75
Maintenance
General Precautions
• Make sure the Projector is turned off and the power cable is unplugged from the power outlet.
• Never remove any parts from the Projector. Contact ViewSonic® or a reseller when any part of the Projector needs replacing.
• Never spray or pour any liquid directly onto the case.
• Handle the Projector with care, as a darker-colored projector, if scuffed, may show marks more clearly than a lighter-colored projector.
Cleaning the Lens
• Use a canister of compressed air to remove dust.
• If the lens is still not clean, use lens-cleaning paper or moisten a soft cloth with lens cleaner and gently wipe the surface.
CAUTION: Never rub the lens with abrasive materials.
Cleaning the Case
• Use a soft, lint-free, dry cloth to remove dirt or dust.
• If the case is still not clean, apply a small amount of non-ammonia, non-alcohol based, mild non-abrasive detergent onto a clean, soft, lint-free cloth, then wipe the surface.
CAUTION: Never use wax, alcohol, benzene, thinner, or other chemical detergents.
Storing the Projector
If you intend to store the Projector for an extended period of time:
• Ensure the temperature and humidity of the storage area are within the recommend range.
• Retract the adjuster foot completely.
• Remove the batteries from the Remote Control.
• Pack the Projector in its original packaging or equivalent.
Disclaimer
• ViewSonic® does not recommend the use of any ammonia or alcohol-based cleaners on the lens or case. Some chemical cleaners have been reported to damage the lens and/or case of the projector.
• ViewSonic® will not be liable for damage resulting from use of any ammonia or alcohol-based cleaners.
76
Light Source Information
This section will provided a better understanding of your projector’s light source.
Light Source Hour
When the projector is being used, the duration (in hours) of light source usage is automatically calculated by the built-in timer.
To obtain the light source hour information:
1. Press Menu to open the OSD Menu and go to: Advanced > Light Source Settings
> Light Source Hours Information.
2. Press Enter and the Light Source Hours Information page will appear.
3. Press Exit to leave the menu.
Extending Light Source Life
To prolong light source life, you can adjust the following settings in the OSD Menu.
Setting Light Source Mode
Setting the projector in any mode other than Normal reduces system noise, power consumption, and extends the light sources operational life.
Light Source Mode Description
Normal Provides full light source brightness.
Eco Reduces light source power consumption by 20% and lowers brightness, and decreases fan noise.
Dynamic Black 1 Reduces light source power consumption by up to 70% depending on the content's brightness level.
Dynamic Black 2 Reduces light source power consumption by up to 50% depending on the content's brightness level.
Custom Allows you to adjust the light source power to extend the light source life and decreases the fan noise.
To set the Light Source Mode, open the OSD Menu and go to: Advanced >
Light Source Settings > Light Source Mode and press / to select and press
Enter .
Setting Auto Power Off
This allows the projector to turn off automatically after a set period of time once no input source is detected.
Open the OSD Menu and go to: POWER MANAGEMENT > Smart Energy >
Auto Power Off and press / to disable or adjust the time.
77
Regulatory and Service Information
Compliance Information
This section addresses all connected requirements and statements regarding regulations. Confirmed corresponding applications shall refer to nameplate labels and relevant markings on the unit.
FCC Compliance Statement
This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
78
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Industry Canada Statement
CAN ICES-003(B) / NMB-003(B)
IC Warning Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, méme si le brouillage est susceptible d’en compromettre le fonctionnement.
Country Code Statement
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.
Pour les produits disponibles aux États-Unis/Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection d’autres canaux n’est pas possible.
79
IC Radiation Exposure Statement
This equipment complied with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. The device for the band 5150-5825 MHz is only for indoor usage to reduce potential for harmful interference to co-channel mobile satellite systems.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC
établies pour un environnement non contrôlê. Cet équipement doit être installé et utilize avec un minimum de 20cm de distance entre la source de rayonnement et votre corps. les dispositifs fonctionnant dans la bande 5150-5825 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage.
Operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
La bande 5 150-5 250 MHz est réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage pré judiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.
CE Conformity for European Countries
The device complies with the EMC Directive 2014/30/EU and Low Voltage
Directive 2014/35/EU. Ecodesign Directive 2009/125/EC and Radio
Equipment Directive 2014/53/EU.
Frequency Range: 2400-2483.5MHz, 5150-5250MHz
Max Output Power: under 20dBm
The following information is only for EU-member states:
The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2012/19/EU (WEEE). The mark indicates the requirement NOT to dispose of the equipment as unsorted municipal waste, but use the return and collection systems according to local law.
80
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Directive
2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2
Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below:
Substance
Lead (Pb)
Mercury (Hg)
Cadmium (Cd)
Hexavalent Chromium (Cr6⁺)
Polybrominated biphenyls (PBB)
Polybrominated diphenyl ethers
(PBDE)
Bis(2-Ethylhexyl) phthalate
(DEHP)
Benzyl butyl phthalate (BBP)
Dibutyl phthalate (DBP)
Diisobutyl phthalate (DIBP)
Proposed Maximum
Concentration
0.1%
0.1%
0.01%
0.1%
0.1%
0.1%
0.1%
0.1%
0.1%
0.1%
Actual Concentration
< 0.1%
< 0.1%
< 0.01%
< 0.1%
< 0.1%
< 0.1%
< 0.1%
< 0.1%
< 0.1%
< 0.1%
Certain components of products as stated above are exempted under the Annex
III of the RoHS2 Directives as noted below. Examples of exempted components are:
• Mercury in cold cathode fluorescent lamps and external electrode fluorescent lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):
ͫ Short length (500 mm): maximum 3.5 mg per lamp.
ͫ Medium length (> 500 mm and 1,500 mm): maximum 5 mg per lamp.
ͫ Long length (> 1,500 mm): maximum 13 mg per lamp.
• Lead in glass of cathode ray tubes.
• Lead in glass of fluorescent tubes not exceeding 0.2% by weight.
• Lead as an alloying element in aluminum containing up to 0.4% lead by weight.
• Copper alloy containing up to 4% lead by weight.
• Lead in high melting temperature type solders (i.e. lead-based alloys containing
85% by weight or more lead).
• Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic matrix compound.
81
Indian Restriction of Hazardous Substances
Restriction on Hazardous Substances statement (India). This product complies with the “India E-waste Rule 2011” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule.
Product Disposal at End of Product Life
ViewSonic® respects the environment and is committed to working and living green. Thank you for being part of Smarter, Greener Computing. Please visit the
ViewSonic® website to learn more.
USA & Canada: https://www.viewsonic.com/us/company/green/go-green-with-viewsonic/#recycle-program
Europe: http://www.viewsoniceurope.com/eu/support/call-desk/
Taiwan: https://recycle.epa.gov.tw/
82
Copyright Information
Copyright© ViewSonic® Corporation, 2022. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft
Corporation in the United States and other countries.
ViewSonic®, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic® Corporation.
VESA is a registered trademark of the Video Electronics Standards Association.
DPMS, DisplayPort, and DDC are trademarks of VESA.
ENERGY STAR® is a registered trademark of the U.S. Environmental Protection
Agency (EPA).
As an ENERGY STAR® partner, ViewSonic® Corporation has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.
Disclaimer: ViewSonic® Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic® Corporation reserves the right to change product specifications without notice. Information in this document may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without prior written permission from ViewSonic® Corporation.
X1_X2_UG_ENG_1a_20220331
83
Customer Service
For technical support or product service, see the table below or contact your reseller.
NOTE: You will need the product’s serial number.
Country/ Region Website Country/ Region
Asia Pacific & Africa
Website
Australia www.viewsonic.com/au/ Bangladesh www.viewsonic.com/bd/
中国 (China)
Hong Kong (English)
Indonesia
日本 (Japan)
Malaysia
Myanmar
New Zealand
Philippines
臺灣 (Taiwan)
Việt Nam
United States
Latin America
Europe
Deutschland
Россия
Türkiye
United Kingdom www.viewsonic.com.cn
www.viewsonic.com/hk-en/ www.viewsonic.com/id/ www.viewsonic.com/jp/ www.viewsonic.com/my/ www.viewsonic.com/mm/ www.viewsonic.com/nz/ www.viewsonic.com/ph/
香港 (繁體中文)
India
Israel
Korea
Middle East
Nepal
Pakistan
Singapore www.viewsonic.com/tw/ www.viewsonic.com/vn/
ประเทศไทย
South Africa & Mauritius
Americas www.viewsonic.com/us Canada www.viewsonic.com/la
Europe www.viewsonic.com/eu/ www.viewsonic.com/de/
France
Қ аза қ стан www.viewsonic.com/ru/ www.viewsonic.com/tr/ www.viewsonic.com/uk/
España
Україна www.viewsonic.com/hk/ www.viewsonic.com/in/ www.viewsonic.com/il/ www.viewsonic.com/kr/ www.viewsonic.com/me/ www.viewsonic.com/np/ www.viewsonic.com/pk/ www.viewsonic.com/sg/ www.viewsonic.com/th/ www.viewsonic.com/za/ www.viewsonic.com/us www.viewsonic.com/fr/ www.viewsonic.com/kz/ www.viewsonic.com/es/ www.viewsonic.com/ua/
84
Limited Warranty
ViewSonic® Projector
What the warranty covers:
ViewSonic® warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period,
ViewSonic® will, at its sole option, repair or replace the product with a like product.
Replacement product or parts may include remanufactured or refurbished parts or components.
Limited Three (3) year General Warranty:
Subject to the more limited one (1) year warranty set out below, North and South
America: Three (3) years warranty for all parts excluding the lamp, three (3) years for labor, and one (1) year for the original lamp from the date of the first consumer purchase.
Other regions or countries: Please check with your local dealer or local ViewSonic® office for the warranty information.
Limited One (1) year Heavy Usage Warranty:
Under heavy usage settings, where a projector’s use includes more than fourteen
(14) hours average daily usage, North and South America: One (1) year warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90) days for the original lamp from the date of the first consumer purchase; Europe: One (1) year warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90) days for the original lamp from the date of the first consumer purchase. Other regions or countries: Please check with your local dealer or local ViewSonic® office for the warranty information. Lamp warranty subject to terms and conditions, verification and approval. Applies to manufacturer’s installed lamp only. All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified, or removed.
2. Damage, deterioration, or malfunction resulting from:
85
ͫ Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product.
ͫ Operation outside of product specifications.
ͫ Operation of the product for other than the normal intended use or not under normal conditions.
ͫ Repair or attempted repair by anyone not authorized by ViewSonic®.
ͫ Any damage of the product due to shipment.
ͫ Removal or installation of the product.
ͫ Causes external to the product, such as electric power fluctuations or failure.
ͫ Use of supplies or parts not meeting Viewsonic’s specifications.
ͫ Normal wear and tear.
ͫ Any other cause which does not relate to a product defect.
3. Removal, installation, and set-up service charges.
How to get service:
1. For information about receiving service under warranty, contact ViewSonic®
Customer Support (Please refer to the “Customer Support” page). You will need to provide your product’s serial number.
2. To obtain warranted service, you will be required to provide: (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.
3. Take or ship the product, freight prepaid, in the original container to an authorized ViewSonic® service center or ViewSonic®.
4. For additional information or the name of the nearest ViewSonic® service center, contact ViewSonic®.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein including the implied warranty of merchantability and fitness for a particular purpose.
86
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product.
ViewSonic® shall not be liable for:
1. Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business relationships, or other commercial loss, even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
Effect of state law:
This warranty gives you specific legal rights, and you may also have other rights which vary from local authority. Some local governments do not allow limitations on implied warranties and/or do not allow the exclusion of incidental or consequential damages, so the above limitations and exclusions may not apply to you.
Sales outside the U.S.A. and Canada:
For warranty information and service on ViewSonic® products sold outside of the
U.S.A. and Canada, contact ViewSonic® or your local ViewSonic® dealer.
The warranty period for this product in mainland China (Hong Kong, Macao, and Taiwan Excluded) is subject to the terms and conditions of the Maintenance
Guarantee Card.
For users in Europe and Russia, full details of warranty provided can be found at: http://www.viewsonic.com/eu/ under “Support/Warranty Information”.
Projector Warranty Term Template In UG
VSC_TEMP_2005
87
Mexico Limited Warranty
ViewSonic® Projector
What the warranty covers:
ViewSonic® warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period,
ViewSonic® will, at its sole option, repair or replace the product with a like product.
Replacement product or parts may include remanufactured or refurbished parts or components & accessories.
How long the warranty is effective:
3 years for all parts excluding the lamp, 3 years for labor, 1 year for the original lamp from the date of the first consumer purchase.
Lamp warranty subject to terms and conditions, verification and approval. Applies to manufacturer’s installed lamp only.
All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty excludes and does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration, or malfunction resulting from:
ͫ Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, unauthorized attempted repair, or failure to follow instructions supplied with the product.
ͫ Any damage of the product due to shipment.
ͫ Causes external to the product, such as electrical power fluctuations or failure.
ͫ Use of supplies or parts not meeting ViewSonic®’s specifications.
ͫ Normal wear and tear.
ͫ Any other cause which does not relate to a product defect.
3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static image is displayed on the product for an extended period of time.
4. Removal, installation, insurance, and set-up service charges.
88
How to get service:
For information about receiving service under warranty, contact ViewSonic®
Customer Support (Please refer to the attached “Customer Service” page). You will need to provide your product’s serial number, so please record the product information in the space provided below on your purchase for your future use.
Please retain your receipt of proof of purchase to support your warranty claim.
For Your Records
Product Name:
Document Number:
Purchase Date:
If so, what date does warranty expire?
Model Number:
Serial Number:
Extended Warranty Purchase?
(Y/N)
1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and
(e) the serial number of the product.
2. Take or ship the product, in the original container packaging, to an authorized
ViewSonic® service center.
3. Round trip transportation costs for in-warranty products will be paid by
ViewSonic®.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein including the implied warranty of merchantability and fitness for a particular purpose.
Exclusion of damages:
ViewSonic®’s liability is limited to the cost of repair or replacement of the product.
ViewSonic® shall not be liable for:
1. Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business relationships, or other commercial loss, even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic®.
89
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:
Name, address, of manufacturer and importers:
México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas,
Col. San Fernando Huixquilucan, Estado de México
Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo:
Distribuciones y Servicios Computacionales SA de CV.
Calle Juarez 284 local 2
Col. Bugambilias C.P: 83140
Tel: 01-66-22-14-9005
E-Mail: [email protected]
Villahermosa:
Compumantenimietnos Garantizados, S.A. de C.V.
AV. GREGORIO MENDEZ #1504
COL, FLORIDA C.P. 86040
Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09
E-Mail: [email protected]
Puebla, Pue. (Matriz):
RENTA Y DATOS, S.A. DE C.V. Domicilio:
29 SUR 721 COL. LA PAZ
72160 PUEBLA, PUE.
Tel: 01(52).222.891.55.77 CON 10 LINEAS
E-Mail: [email protected]
Chihuahua:
Soluciones Globales en Computación
C. Magisterio # 3321 Col. Magisterial
Chihuahua, Chih.
Tel: 4136954
E-Mail: [email protected]
Distrito Federal:
QPLUS, S.A. de C.V.
Av. Coyoacán 931
Col. Del Valle 03100, México, D.F.
Tel: 01(52)55-50-00-27-35
E-Mail : [email protected]
Guerrero Acapulco:
GS Computación (Grupo Sesicomp)
Progreso #6-A, Colo Centro
39300 Acapulco, Guerrero
Tel: 744-48-32627
Veracruz, Ver.:
CONEXION Y DESARROLLO, S.A DE C.V. Av.
Americas # 419
ENTRE PINZÓN Y ALVARADO
Fracc. Reforma C.P. 91919
Tel: 01-22-91-00-31-67
E-Mail: [email protected]
Cuernavaca:
Compusupport de Cuernavaca SA de CV
Francisco Leyva # 178 Col. Miguel Hidalgo
C.P. 62040, Cuernavaca Morelos
Tel: 01 777 3180579 / 01 777 3124014
E-Mail: [email protected]
Guadalajara, Jal.:
SERVICRECE, S.A. de C.V.
Av. Niños Héroes # 2281
Col. Arcos Sur, Sector Juárez
44170, Guadalajara, Jalisco
Tel: 01(52)33-36-15-15-43
E-Mail: [email protected]
Monterrey:
Global Product Services
Mar Caribe # 1987, Esquina con Golfo Pérsico
Fracc. Bernardo Reyes, CP 64280
Monterrey N.L. México
Tel: 8129-5103
E-Mail: [email protected]
MERIDA:
ELECTROSER
Av Reforma No. 403Gx39 y 41
Mérida, Yucatán, México CP97000
Tel: (52) 999-925-1916
E-Mail: [email protected]
Tijuana:
STD
Av Ferrocarril Sonora #3780 L-C
Col 20 de Noviembr
Tijuana, Mexico
Oaxaca, Oax.:
CENTRO DE DISTRIBUCION Y
SERVICIO, S.A. de C.V.
Murguía # 708 P.A., Col. Centro, 68000, Oaxaca
Tel: 01(52)95-15-15-22-22
Fax: 01(52)95-15-13-67-00
E-Mail. [email protected]
FOR USA SUPPORT:
ViewSonic ® Corporation
381 Brea Canyon Road, Walnut, CA. 91789 USA
Tel: 800-688-6688
E-Mail: http://www.viewsonic.com
Projector Mexico Warranty Term Template In UG
VSC_TEMP_2006
90
Process Color C0 M91 Y72 K24
Process Color C0 M0 Y0 K100
Process Color C0 M91 Y72 K24
Spot Color
Spot Color
Pantone Black C
Pantone 187 C
Spot Color
Or Spot Color
Pantone Black C
Pantone 187 C
Ladda ner
Offentlig länk uppdaterad
Den offentliga länken till din chatt har uppdaterats. You may view and manage your chat links after registration here.
Offentlig länk till dokument
Annons
Huvudfunktioner
3rd generation LED technology with a 30,000-hour lifespan
3,100 LED Lumens for bright and clear images in any environment
Cinema SuperColor+™ Technology with 125% Rec.709 wide color gamut
Custom-built speakers by Harman Kardon
Smart connectivity via Wi-Fi, Bluetooth, and USB-C
V lens shift, H/V keystone, and 1.3x zoom for easy setup