Sylvania 6719DE Tv Vcr Combo Owner`s manual

OWNER’S

MANUAL

COLOR TV/VCR/DVD TRIPLE COMBO

6719DE

(19 inch)

SUPPLIED ACCESSORIES

ACCESSORIES

Remote Control Unit

Batteries

Owner’s Manual

PART NO.

NE222UD

2 AA Batteries

1EMN20246

INSTRUCCIONES EN ESPAÑOL INCLUIDAS.

As an E NERGY S TAR

Partner, our company has determined that this product meets the E NERGY S TAR guidelines for energy efficiency. E NERGY S TAR is a U.S. registered mark.

If you need additional operating assistance after reading this owner’s manual or to order replacement accessories, please call

TOLL FREE : 1-800-968-3429.

Or visit our WEB SITE at http://www.funai-corp.com

Please read before using this equipment

WARNING :

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLI-

ANCE TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER SERVIC-

ING TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DAN-

GEROUS VOLTAGE CONSTITUTING A

RISK OF ELECTRIC SHOCK IS PRESENT

WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE

ARE IMPORTANT OPERATING AND

MAINTENANCE INSTRUCTIONS IN THE

LITERATURE ACCOMPANYING THE

APPLIANCE.

The caution marking is located on the rear of the cabinet.

IMPORTANT SAFEGUARDS

1.Read instructionsAll the safety and operating instructions should be read before the appliance is operated.

2.Retain InstructionsThe safety and operating instructions should be retained for future reference.

3.Heed Warnings -All warnings on the appliance and in the operating instructions should be adhered to.

4.Follow InstructionsAll operating and use instructions should be followed.

5.CleaningUnplug the unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5.

6.AttachmentsDo not use attachments not recommended by the unit manufacturer as they may cause hazards.

7.Water and MoistureDo not use this unit near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.

8.AccessoriesDo not place this unit on an unstable cart, stand, tripod, bracket, or table. The unit may fall, causing serious injury to someone, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the unit.

Any mounting of the appliance

PORTABLE CART WARNING should follow the manufacturer’s instructions and should use a mounting accessory recommended by the manufacturer. An appliance and cart combination should be moved with care.Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

S3126A

AMEUBLESCet appareil ne doit être placé que sur un meuble (avec ou sans roulettes) recommandé par le fabricant.

Si vous l’installez sur un meuble à roulettes, déplacez les

SYMBOLE D'AVERTISSEMENT POUR

LES COMPOSANTES

APPAREIL ET MEUBLE A ROULETTES deux ensembles avec précaution. Un arrêt brusque, l’utilisation d’une force excessive et

S3126A des surfaces irrégulières risquent de déstabiliser l’ensemble et de le renverser.

9.VentilationSlots and openings in the cabinet and the back or bottom are provided for ventilation and to ensure reliable operation of the unit and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat register. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

10.Power SourcesThis unit should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For units intended to operate from battery power, or other sources, refer to the operating instructions.

11.Grounding or PolarizationThis unit is equipped with a polarized alternating-current line plug(a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

12.Power-Cord Protection -Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

- 2 EN

1B15

F IGUR E A

EXAMPLE OF ANTENNA GROUNDING AS PER

NA TIONA L ELECT RIC AL CODE

GROUN D

C L A M P

AN TE NN A

L E A D I N

W I R E

E L E CT RI C

S E RV I CE

E Q U I P M E N T

S 2 8 9 8 A

NE C - NA TI O NAL EL E CTRI CAL CO DE

A NTEN NA

DI S CHA RG E UN I T

(NEC SE CTI ON 8 10 -2 0)

G RO UNDI NG CO NDUCT ORS

(NEC SE CTI ON 8 10 -2 1)

G RO UND CL AM PS

P OWE R S E RVI C E G RO UNDI NG

E L E C TR O DE S Y S T E M

(NEC A RT 2 50 , P ART H)

13.Outdoor Antenna groundingIf an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges.

Article 810 of the National Electrical Code, ANSI/NFPA

No. 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A)

14.LightningFor added protection for this unit receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power-line surges.

15.Power LinesAn outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

16.OverloadingDo not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

17.Object and Liquid EntryNever push objects of any kind into this unit through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the unit.

18.ServicingDo not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19.Damage Requiring ServiceUnplug this unit from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged or frayed.

b. If liquid has been spilled, or objects have fallen into the unit.

c. If the unit has been exposed to rain or water.

d. If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation.

e. If the unit has been dropped or damaged in any way.

f. When the unit exhibits a distinct change in performancethis indicates a need for service.

20.Replacement PartsWhen replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, injury to persons or other hazards.

21.Safety CheckUpon completion of any service or repairs to this unit, ask the service technician to perform routine safety checks to determine that the unit is in proper operating condition.

22.HeatThis TV/VCR/DVD product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

- 3 EN

1B15

PRECAUTIONS

IMPORTANT COPYRIGHT INFORMATION

Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by

Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

RADIO-TV INTERFERENCE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment and receiver.

3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4) Consult the dealer or an experienced radio/TV technician for help.

LASER SAFETY

This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury.

CAUTION: USE OF CONTROLS OR ADJUST-

MENTS OR PERFORMANCE OF PROCE-

DURES OTHER THAN THOSE SPECIFIED

HEREIN MAY RESULT IN HAZARDOUS

RADIATION EXPOSURE.

CAUTION: VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN AND INTERLOCK

DEFEATED. DO NOT STARE INTO BEAM.

LOCATION: INSIDE, NEAR THE DECK

MECHANISM.

This Class B digital apparatus complies with

Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE

SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOCS

ÉLECTRIQUES, INTRODUIRE LA LAME LA

PLUS LARGE DE LA FICHE DANS LA

BORNE CORRESPONDANTE DE LA PRISE

ET POUSSER JUSQU’AU FOND.

A NOTE ABOUT RECYCLING

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.

- 4 EN

1B15

LOCATION

For safe operation and satisfactory performance of your TV/VCR/DVD, keep the following in mind when selecting a place for its installation:

• Shield it from direct sunlight and keep it away from sources of intense heat.

• Avoid dusty or humid places.

• Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the top and bottom of the unit. Do not place the unit on a carpet because this will block the ventilation holes.

• Install unit in a horizontal position.

• Avoid locations subject to strong vibration.

• Do not place the unit near strong magnetic fields.

• Avoid moving the unit to locations where temperature differences are extreme.

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

• Do not handle the power cord with wet hands.

• Do not pull on the power cord when disconnecting it from an AC wall outlet. Grasp it by the plug.

• If, by accident, water is spilled on your unit, unplug the power cord immediately and take the unit to our

Authorized Service Center for servicing.

• Do not put your fingers or objects into the disc loading tray of the unit.

• Do not place anything directly on top of the unit.

WARNING

Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, or after heating a cold room or under conditions of high humidity. If a DVD is played in a unit which has moisture, it may damage the DVD and unit.

Therefore when the condensation occurs inside the unit, turn the unit on and allow at least 2 hours for the unit to dry out.

SYMBOLS USED IN THIS MANUAL

The following symbols below appear in some headings and notes in this manual, with the following meanings

TV/VCR

: Description refers to TV/VCR operation

(in the TV/VCR mode).

DVD-V

: Description refers to playback of DVD video discs

(in the DVD mode).

CD

: Description refers to playback of Audio CDs

(in the DVD mode).

MP3

: Description refers to playback of MP3 discs

(in the DVD mode).

QUICK

: Description refers to the items to be set by the

QUICK mode (in the DVD mode).

The serial number of this product may be found on the back of the unit. No other TV/VCR/DVD has the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

- 5 EN

1C29

C IMPORTANT SAFEGUARDS . . .2, 3

C PRECAUTIONS . . . . . . . . . . . . . . . .4

LOCATION . . . . . . . . . . . . . . . . . . .5

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE .5

WARNING . . . . . . . . . . . . . . . . . . . .5

SYMBOLS USED IN THIS

MANUAL . . . . . . . . . . . . . . . . . . . . .5

C TABLE OF CONTENTS . . . . . . . . . .6

C FEATURES . . . . . . . . . . . . . . . . . . . .7

C OPERATING CONTROLS AND

FUNCTIONS . . . . . . . . . . . . . . . .9, 10

C PREPARATION FOR USE . . . . . . .11

ANTENNA/CABLE

CONNECTION . . . . . . . . . . . . . . . .11

CONNECTING TO EXTERNAL

INPUT JACKS . . . . . . . . . . . . . . . .12

INSTALLING THE BATTERIES . .12

EXTERNAL INPUT MODE . . . . . .12

CONNECTING TO A STEREO

AMPLIFIER EQUIPPED WITH DIGI-

TAL INPUT JACKS (for DVD) . . .13

CONNECTING TO A DOLBY

DIGITAL DECODER (for DVD) . .14

TV/VCR SECTION

C SET UP FOR USE . . . . . . . . . . . . .15

SELECTING THE LANGUAGE . .15

CLOCK SET UP

(AUTO / MANUAL) . . . . . . . . .15, 16

DAYLIGHT-SAVING TIME . . . . . .17

CHANNEL SET UP . . . . . . . . . . . .18

DELETING (OR ADDING)

CHANNEL . . . . . . . . . . . . . . . . . . .18

C TV OPERATION . . . . . . . . . . . . . . .19

WATCHING A TV PROGRAM . . .19

DEGAUSSING . . . . . . . . . . . . . . . .19

PICTURE CONTROL . . . . . . . . . . .19

CLOSED CAPTION SYSTEM . . . .20

V-CHIP SET UP . . . . . . . . . . . . . . .21

C MTS (Multi-Channel Television sound) SYSTEM . . . . . . . . . . . . . . .23

CHECKING THE SELECTED

MTS MODE . . . . . . . . . . . . . . . . . .23

MTS RECORDING/MONITOR

MODE . . . . . . . . . . . . . . . . . . . . . .23

SELECTING THE MTS SYSTEM .24

C

VIDEO CASSETTE . . . . . . . . . . . . .25

C PLAYBACK . . . . . . . . . . . . . . . . . . .26

NORMAL PLAYBACK . . . . . . . . .26

TRACKING ADJUSTMENT . . . . .26

SLOW MOTION . . . . . . . . . . . . . .26

STILL PICTURE . . . . . . . . . . . . . .26

VERTICAL HOLD CONTROL . . .26

C SPECIAL PLAYBACK . . . . . . . . . .27

RENTAL PLAYBACK . . . . . . . . . .27

AUTO REPEAT PLAYBACK . . . . .27

C SEARCH . . . . . . . . . . . . . . . . . . . . .28

ZERO RETURN . . . . . . . . . . . . . . .28

PICTURE SEARCH . . . . . . . . . . . .28

TIME SEARCH . . . . . . . . . . . . . . .28

INDEX SEARCH . . . . . . . . . . . . . .29

C SPECIAL FEATURES . . . . . . . . . .29

REAL TIME TAPE COUNTER . . .29

AUTO REWIND-EJECT . . . . . . . .29

C RECORDING . . . . . . . . . . . . . . . . .30

NORMAL RECORDING . . . . . . . .30

SKIPPING UNWANTED SCENES

DURING

RECORDING . . . . . . . . . . . . . . . . .30

OTR (One Touch Recording) . . . . . .31

COPYING A VIDEO CASSETTE

(Requires a VCR or camcorder) . . .31

C TIMER RECORDING . . . . . . . . . . .32

AUTOMATIC

TIMER RECORDING . . . . . . . . . .32

TIMER PROGRAM EXTENSION .33

HINTS FOR AUTOMATIC TIMER

RECORDING . . . . . . . . . . . . . . . . .34

AUTO RETURN . . . . . . . . . . . . . . .34

SLEEP TIMER . . . . . . . . . . . . . . . .34

C ON SCREEN DISPLAY . . . . . . . . .35

C CABLE CHANNEL

DESIGNATIONS . . . . . . . . . . . . . .35

DVD SECTION

C ABOUT THE DISCS . . . . . . . . . . . .36

PLAYABLE DISCS . . . . . . . . . . . .36

DISC TYPES . . . . . . . . . . . . . . . . .36

C PLAYING A DISC . . . . . . . . . . . . . .37

BASIC PLAYBACK . . . . . . . . . . . .37

GENERAL FEATURES . . . . . . . . .37

DISC MENU . . . . . . . . . . . . . . . . .37

TITLE MENU . . . . . . . . . . . . . . . . .37

TABLE OF CONTENTS

RESUME . . . . . . . . . . . . . . . . . . . .38

PAUSE . . . . . . . . . . . . . . . . . . . . . .38

STEP BY STEP PLAYBACK . . . . .38

FAST FORWARD / FAST

REVERSE . . . . . . . . . . . . . . . . . . . .38

SLOW FORWARD / SLOW

REVERSE . . . . . . . . . . . . . . . . . . . .38

C SEARCH FUNCTION . . . . . . . . . . .39

TRACK SEARCH . . . . . . . . . . . . .39

TITLE / CHAPTER SEARCH . . . .39

TIME SEARCH . . . . . . . . . . . . . . .39

MARKER SETUP SCREEN . . . . . .39

C SPECIAL PLAYBACK FUNCTION . . .40

REPEAT . . . . . . . . . . . . . . . . . . . . .40

PROGRAM . . . . . . . . . . . . . . . . . . .40

RANDOM PLAYBACK . . . . . . . . .40

C PLAYING A MP3 DISC . . . . . . . . . .41

MP3 PLAYBACK . . . . . . . . . . . . . .41

REPEAT . . . . . . . . . . . . . . . . . . . . .41

PROGRAM . . . . . . . . . . . . . . . . . . .41

RANDOM PLAYBACK . . . . . . . . .41

C CHANGING THE SETTINGS . . . .42

SUBTITLE LANGUAGE . . . . . . . .42

AUDIO LANGUAGE . . . . . . . . . . .42

STEREO SOUND MODE . . . . . . . .42

CAMERA ANGLE . . . . . . . . . . . . .42

BLACK LEVEL SETTING . . . . . . .42

VIRTUAL SURROUND . . . . . . . . .42

C THE ON-SCREEN INFORMATION . . .43

C CHANGING THE DVD SETUP

ITEMS . . . . . . . . . . . . . . . . . . . . . . .44

LANGUAGE SETTING . . . . . . . . .44

DISPLAY SETTING . . . . . . . . . . . .45

AUDIO SETTINGS . . . . . . . . . . . .45

PARENTAL CONTROL . . . . . . . . .46

INITIALIZE . . . . . . . . . . . . . . . . . .46

C TROUBLESHOOTING GUIDE . . .47

C MAINTENANCE . . . . . . . . . . . . . . .50

DISC HANDLING . . . . . . . . . . . . .50

C SPECIFICATIONS . . . . . . . . . . . . .51

C ESPAÑOL . . . . . . . . . . . . . . . . . . . .52

C WARRANTY . . . . . . . . . . .Back Cover

- 6 EN

1C29

FEATURES

TV/VCR Mode

•

Hi-Fi system– The Hi-Fi stereo recording system offers you excellent sound quality with a dynamic range of 80dB, frequency response from 20Hz to

20kHz, and 0.005% wow and flutter.

• Rotary 4-head Record/Playback System– Four heads ensure excellent picture quality and special effects playback.

• Index Search– Fast-forwards to start of next recording.

• Slow Motion– View recorded program at slower than normal speed.

• Infrared remote control

• Trilingual on screen TV/VCR setup display selectable in English or Spanish or French

• Real time counter– This shows the elapsed recording or playback time in hours, minutes, and seconds. The “–” indication will appear when the tape is rewound further than the tape counter position

“0:00:00”.

• 181 channel capability PLL frequency synthesizer tuner with direct station call– (A converter may be necessary to view scrambled cable channels.)

• Auto Clock Setting– Allows you to set the clock function from a PBS broadcast station.

• Closed caption system– You may view specially labeled (cc) TV programs, movies, news, prerecorded tapes, etc. with either a dialogue caption or text display added to the program.

• Auto power on and off system– Automatically turns on the unit when you insert the cassette, turns off after auto-rewind, and ejects when the beginning of the tape is reached.

•

Auto rewind when the end of a tape is reached– This function doesn’t occur when using timer recording.

• Smooth mode change– TV/VCR mode, DVD mode automatically changes without control.

•

2 Step picture search operation– You can view a video program at a high speed or super high speed in either a forward or reverse direction in LP and

SLP mode. For SP mode only high speed.

• Three different playback tape speeds : SP/LP/SLP

• Two different recording tape speeds : SP/SLP

• Auto Head Cleaner– Automatically cleans video heads as you insert or remove a cassette.

• Zero Return– The tape returns to counter of

0:00:00 by rewinding or fast forwarding.

• Still– “Freeze” the picture at any time, for close viewing of a particular scene.

• Digital Auto Tracking (DTR)– Automatically adjusts the tracking for each tape you play.

• Rental play mode– Improves playback picture quality from worn tapes, such as rental tapes.

•

Auto repeat– Allows you to repeat the playing of a tape indefinitely without pressing the PLAY button.

• Time search– Let you set the unit to advance the tape by entering the desired playback time you want to skip.

• OTR (One Touch Recording)– Instant timed recording from 30 to 480 minutes is possible at the push of the REC/OTR button.

• 1 Year, 8 events (including Daily and Weekly)

Timer Recording– The built-in timer allows you to record up to 8 programs at different times on different channels up to 1 year in advance. The Daily timer allows recordings to be made of daily broadcasts, and the Weekly timer allows recording to be made once a week up to the end of the tape.

•

Auto return– After timer recording is finished, the unit can return to the beginning of the recording.

• Sleep timer– Allows you to have the unit automatically turn off at a desired time.

• Timer Program Extension– Allow you to shift the time schedule for automatic timer recording.

• V-CHIP– Enables parents to prevent their children from watching inappropriate material on TV.

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.

- 7 EN

1C29

DVD Mode

¡ Dolby Digital sound

This unit can handle Dolby Digital surround sound having 5.1 channels when connected to a Dolby

Digital decoder .

¡ Still / fast / slow / step playback

Various playback modes are available including still pictures, fast forward/reverse, slow motion and step frames.

¡ Random playback for Audio CD and MP3

This unit can shuffle the order of tracks to play them in random order.

¡ Program playback for Audio CD and MP3

You can program the order of tracks to play them in any desired order.

¡ DVD menus in a desired language

You can display DVD menus in a desired language, if available on a DVD.

¡ Screen saver/Auto power-off functions

The screen saver program starts when there is no input from the unit for 5 minutes in the stop mode.

After the screen saver program is activated for 15 minutes, the power is automatically turned off.

¡ Subtitles in a desired language

You can select a desired language for the display subtitles, if that language is available on a disc.

¡ Selecting a camera angle

You can select the desired camera angle, if a disc contains sequences recorded from different angles.

¡ Choices for audio language and sound mode

You can select the desired audio language and sound mode, if different languages and modes are available on a disc.

¡ Parental lock

You can set the control level to limit playback of discs which may not be suitable for children.

¡ Automatic detection of discs

This unit automatically detects if the loaded disc is

DVD, Audio CD or MP3 on disc.

¡ Playback MP3 disc

¡ On-screen display

Information about the current operation can be displayed on a TV screen, allowing you to confirm the currently active functions (such as program playback), on the TV screen using the remote control.

¡ Search

Chapter search / Title search / Track search / Time search

¡ Repeat

Chapter / Title / Track / Group / All / A-B

¡ Marker

The part designated by user can be called back.

¡ Resume Play

User can resume to playback from the part at which the play was stopped.

¡ Virtual Surround

¡ Bit rate indication

¡ DRC (Dynamic range control)

You can control the range of sound volume.

NOTE:

• We do not recommend the use of universal remote controls. Not all of the functions may be controlled with a universal remote control.

If you decide to use a universal remote control with this unit, please be aware that the code number given may not operate this unit. In this case, please call the manufacturer of the universal remote control.

- 8 EN

1C29

OPERATING CONTROLS AND FUNCTIONS

- FRONT PANEL - [Fig.1]

1

1

22

23

24

25

26

(DVD)

3

(TV/VCR)

14

4

13

27

28

29

30

31

32

33

2

- REMOTE CONTROL -

POWER PICTURE SLEEP SELECT

1

4

7

PAUSE

8

0

SPEED C.RESET

9

+100

+10

V.SURR

VOL.

MUTE

RECORD

DISPLAY

SETUP

CLEAR SEARCH MODE REPEAT

MODE

3

2

5

PLAY

STOP

TITLE

4

3

6

3

ENTER

CH.

DISC

MENU

A-B

AUDIO SUBTITLE ANGLE

5 6

[Fig. 2]

RETURN

45

44

11

2

43

42

3 (DVD)

15

(TV/VCR)

5

41

40

39

38

37

36

35

34

7 8 9 10

1.

POWER Button [TV/VCR P.15 / DVD P.37]

Press to turn the power on and off.

2.

VOLUME X / Y Buttons

Press to control the volume level for the DVD and TV.

3.

SKIP Buttons (for DVD) [P.38]

Press once to skip chapters or tracks to a desired point.

Press and hold to change forward or reverse playback speed.

4.

PLAY Button [TV/VCR P.26 / DVD P.37]

Starts playback of the disc or tape contents.

- 9 -

11 12 13 14 4 15 16 17 18 19 20 21

5.

STOP Button [TV/VCR P.26 / DVD P.37]

Stops operation of the disc. (or front panel)

Stops operation of the disc or tape contents.

(remote control)

6.

OPEN/CLOSE Button [DVD P.37]

Press to insert discs into or remove them from the tray.

7.

Disc loading tray

8.

DVD Indicator

Lights on during DVD mode.

9.

SELECT Button

Press to change to TV/VCR mode, external input mode or DVD mode.

10.

TV/VCR Indicator

Lights on during TV/VCR mode.

11.

CHANNEL K / L Buttons

Press to select memorized channel.

12.

Recording Indicator

Flashes during recording. Lights up in the Standby mode for Timer Recording.

13.

REC/OTR Button (Front Panel) [TV/VCR P.30, 31]

Press to start manual recording. Press repeatedly to start One Touch Recording (only during

TV/VCR mode).

RECORD Button (Remote Control) [TV/VCR P.30]

Press to start manual recording.

14.

REW Button (for TV/VCR) [TV/VCR P.26]

Press to rewind the tape, or to view the picture rapidly in reverse during playback mode. (Rewind

Search)

15.

F.FWD Button (for TV/VCR) [TV/VCR P.26]

Press to rapidly advance the tape, or to view the picture rapidly in forward during playback mode.

(Forward Search)

16.

STOP/EJECT Button [TV/VCR P.28]

Press to stop the tape motion. Press in the Stop mode to remove tape from the unit.

17.

Remote sensor window

18.

HEADPHONE Jack

To connect headphone (not supplied) for personal listening.

EN

1C29

- REAR PANEL - [Fig.3]

ANT.

AUDIO OUT

COAXIAL

46 47 48

19.

VIDEO input Jack

Connect to the video output jack of a video camera or VCR.

20.

AUDIO L/R input Jacks

Connect to the audio output jacks of a video camera or VCR.

21.

Cassette compartment

22.

PICTURE Button

Press to adjust the picture.

23.

Number Buttons

TV/VCR Mode: [P.15]

Press two digits to directly access the desired channel.

Remember to press "0" before a single digit channel.

+100 Button–

Press to select cable channels which are equal or greater than number 100.

DVD Mode:

Press to enter the desired number.

+10 Button–

Press to enter the desired numbers which are equal or greater than number 10.

24.

PAUSE Button [TV/VCR P.26 / DVD P.38]

Pauses the current disc or tape operation.

25.

SPEED Button [TV/VCR P.30]

Press to choose the desired recording speed:

SP/SLP.

26.

C.RESET Button [TV/VCR P.28]

Press to reset counter to 0:00:00.

Press to cancel a setting of timer program. (See page 33.)

27.

DISPLAY Button

TV/VCR Mode:

Display the counter or the current channel number and current time on the TV screen.

DVD Mode: [P.43]

Displays the current status on the TV screen.

28.

SETUP Button [TV/VCR P.15] [DVD P.44-46]

Press to enter or exit the TV menu or DVD setup mode.

29.

TITLE Button [DVD P.37]

Displays the title menu.

30.

CLEAR Button

Resets a setting.

31.

MODE Button [DVD P.41]

Activates program playback or random playback mode.

32.

SEARCH MODE Button [DVD P.39]

Press to locate a desired point.

33.

AUDIO Button [DVD P.42]

Press to select a desired audio language or sound mode.

34.

SUBTITLE Button [DVD P.42]

Press to select a desired subtitle language.

35.

REPEAT Button [DVD P.42]

Repeats playback of the current disc, title, chapter or track.

36.

ANGLE Button (DVD mode) [DVD P.42]

Press to change the camera angle to see the sequence being played back from a different angle.

37.

A-B REPEAT Button [DVD P.40]

Repeats playback of a selected section.

38.

RETURN Button

Returns to the previous operation in the DVD setup mode.

39.

ENTER Button

Press to accept a setting.

40.

Arrow Buttons

TV/VCR Mode:

Press to select a setting mode from the menu on the TV screen.

Press to select or adjust from a particular menu.

DVD Mode:

Use when making settings while watching the display on a TV screen.

41.

DISC MENU Button [DVD P.37]

Displays the DVD menus.

Calls up the file list in MP3 disc.

42.

V. SURR (VIRTUAL SURROUND) Button [DVD P.42]

Sets virtual surround on/off.

43.

MUTE Button

Mutes the sound. Press it again to resume sound.

44.

SLEEP Button [TV/VCR P.34]

Sets the Sleep Timer.

- 10 EN

1C29

45.

SELECT Button

Press to switch TV/VCR and DVD mode. You can see the mode (TV/VCR or DVD) on the front panel indicator.

46.

ANT. in Jack

Connect to an antenna, cable system, or satellite system.

47.

Power cord

Connect to a standard AC outlet (120V/60Hz).

NOTE: Remove the power cord from the hook to avoid breaking a wire before you connect to a standard AC outlet.

48.

COAXIAL digital audio out Jack

Connect to the digital input of an external amplifier or decoder (for DVD audio only).

Satellite Box or

Cable Box (Not supplied)

OUT

IN

PREPARATION FOR USE

ANTENNA/CABLE CONNECTION

From Cable System or

Satellite Dish

VHF/UHF Antenna

(Not supplied)

VHF Antenna (Not supplied)

From Cable

System

75-ohm

Coaxial

Cable

(Not supplied)

ANT.

75-ohm Coaxial

Cable (Not supplied) or

AUDIO OUT

COAXIAL

ANT.

or

UHF Antenna

(Not supplied)

VHF/UHF

Combiner

(Not supplied)

Flat twin-lead cable

[Fig. 4] or

VHF/UHF SEPARATE ANTENNAS

In some areas it will be necessary to use an outdoor antenna.

CABLE WITHOUT CONVERTER/

DESCRAMBLER BOX

Use this connection if your cable system connects directly to your unit without a converter box.

By using this connection you can:

1) Use the unit’s remote to select channels.

2) Program one or more unscrambled channels for

Automatic Timer Recording.

NOTE: This unit will ONLY record and view the same channel.

CABLE WITH CONVERTER/

DESCRAMBLER BOX OR SATELLITE

BOX

If your cable service supplies you with a converter box or if you use a satellite system, you can use the basic connection shown in the illustration.

By using this connection you can also record scrambled channels. However, channel selection must be made with the converter box or satellite box. This means that channels cannot be changed using the unit’s remote control. Unattended timer recording is limited to one channel at a time.

Antenna/Cable Connections

Continued on the Next Page.

- 11 EN

1C29

TO RECORD A SCRAMBLED/UNSCRAM-

BLED CHANNEL

1. Set the unit’s channel selector to the output channel of the Cable Converter Box or Satellite Box.

(Ex. CH3)

2.Select the channel to record from your Cable

Converter Box or Satellite Box.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the

NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.

CONNECTING TO EXTERNAL

INPUT JACKS

When you watch a program recorded on an another source (VCR or video camera), use the

AUDIO/VIDEO input jacks on the front of this unit.

Connect the audio/video output jacks of another source to the AUDIO L/R and VIDEO jacks on the front panel.

Then press the CHANNEL button K or L until

“AUX” appears on the screen.

NOTE:

• When you connect a monaural VCR (another source) to this unit, connect the Audio output jack of the monaural VCR (another source) to the

AUDIO L jack of this unit. The audio will output in both L and R channel equally.

To the audio output jacks

[Another source]

INSTALLING THE BATTERIES

1)Open the battery compartment cover by pressing the cover on the remote unit in the direction of the arrow.

2)Insert 2 “AA” penlight batteries into the battery compartment in the direction indicated by the polarity (+/-) markings.

3)Replace the cover.

EXTERNAL INPUT MODE

When using an external input signal (another VCR or video camera), connect the player’s Audio/Video output cables to the AUDIO L/R IN/

VIDEO IN jacks of this unit. Then

AUX press the CHANNEL button K or

L until “AUX” appears on the screen.

etc.

To the video output jack

Audio/Video cable

(not supplied)

HEADPHONE VIDEO L-AUDIO-R

[Front of the unit]

[Fig. 5]

- 12 EN

1C29

CONNECTING TO A STEREO AMPLIFIER

EQUIPPED WITH DIGITAL INPUT JACKS (for DVD)

Use an audio coaxial digital cable available at retail for the audio connections.

Connecting to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.

ANT.

AUDIO OUT

COAXIAL

Amplifier equipped with digital input jacks, MD deck,

DAT deck, etc.

To COAXIAL DIGITAL

AUDIO INPUT jack

To DIGITAL AUDIO OUT

(PCM/BITSTREAM)

COAXIAL jack

(Only DVD AUDIO OUT)

[Fig. 6]

NOTES:

• The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital sound by an MD or DAT deck.

• Be sure to turn off the power to all components in the system before connecting another component.

• Refer to the Owner's Manuals for the components to be connected to the unit.

• Set Dolby Digital to OFF for audio output in the setup mode. Playing a unit using incorrect settings may generate noise distortion, and may also damage the speakers.

- 13 EN

1C29

CONNECTING TO A DOLBY DIGITAL DECODER (for DVD)

If using this unit to play a DVD disc in a 5.1 channel Dolby Digital surround format, the unit outputs a

DOLBY DIGITAL Data stream from its COAXIAL digital audio out jack. By hooking the unit up to a Dolby

Digital decoder, you can enjoy a more convincing, realistic ambience with powerful and high-quality surround sound as enjoyed in movie theaters.

Use audio coaxial digital cables available at retail for the audio connections.

Front speaker

(left)

Center speaker

Front speaker

(right)

ANT.

AUDIO OUT

COAXIAL

Surround speaker

(left)

Dolby Digital decoder

Surround speaker

(right)

To COAXIAL DIGITAL

AUDIO INPUT jack

Subwoofer

To DIGITAL AUDIO OUT

(PCM/BITSTREAM)

COAXIAL jack

(Only DVD AUDIO OUT)

[Fig. 7]

NOTES:

• Be sure to turn off the power to all components in the system before connecting another component.

• Refer to the Owner's Manuals for the components to be connected to the unit.

• If connected to a Dolby Digital decoder, set DOLBY DIGITAL to ON for audio output in the setup mode.

(See page 45 to set DOLBY DIGITAL to ON.)

• Unless connected to a Dolby Digital decoder, set DOLBY DIGITAL to OFF for audio output in the setup mode. Playing a unit using incorrect settings may generate noise distortion, and may also damage the speakers.

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

- 14 EN

1C29

TV/VCR SECTION

SET UP FOR USE

SELECTING THE LANGUAGE

TV/VCR

1

Plug in theu nit’s power cord

Plug the unit’s power cord into a standard

AC outlet.

NOTE:

• If any digits appear in the corner of the screen, press the POWER button without unplugging the power cord.

Make sure ...

• Press the SELECT button to select TV/VCR mode, or make sure TV/VCR lights on.

• Press the POWER button to turn on the unit.

NOTE: This function effects only the language on the screen menu and not the audio source.

CLOCK SET UP

(AUTO / MANUAL)

TV/VCR

The unit’s clock must be set correctly before VCR timer recording is possible. It is suggested that the clock be set manually when first setting up the unit.

Then, set to [ON] the auto clock setting which will periodically correct the setting if necessary.

NOTE: If you cannot receive a station with time signals, auto clock setting cannot be performed. Use manual setting only.

MANUAL CLOCK SETTING

Make sure ...

• The unit is turned on.

In the example below, the clock is to be set to:

DATE May 5th, 2005

SETTING TIME 5:40PM

2

Select “LANGUAGE”

Press the SETUP button on the remote control.

Press the Arrow button K or L to point to “LANGUAGE”.

B

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

3

Select “ENGLISH”, “ESPAÑOL” or “FRANÇAIS”

Select “ENGLISH”, “ESPAÑOL”= Spanish or

“FRANÇAIS”= French using the ENTER button.

4

Exit the Language mode

Press the SETUP button on the remote control to return to TV mode.

NOTE: If for some reason the menu is in Spanish or

French, press the SETUP button on the remote control, press the Arrow button K or L to point to “IDIOMA

[ESPAÑOL]” or “LANGAGE [FRANÇAIS]”, then press the ENTER button, then press the SETUP button on the remote control.

1

Select “SETTING CLOCK”


Press the Arrow button K or L to point to “SETTING CLOCK”.

Then press the ENTER button.

- TV/VCR SETUP -

TIMER PROGRAMMING

B SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

2

Select “MANUAL CLOCK SET”

Press the Arrow button K or L to point to “MANUAL CLOCK

SET”.

AUTO CLOCK [ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

B MANUAL CLOCK SET

[ 02 ]

D.S.T.

[OFF]


– SETTING CLOCK –

3

Select the month

Press the Arrow button K or L until your desired month appears.

(Example: May → 05)

Then, press the Arrow button B .

(Or press the Arrow button { to go back one step.)

– MANUAL CLOCK SET –

MONTH DAY YEAR

0 5 / – – – – – – – – –

HOUR MINUTE

– – : – – – –

4

Select the day

Press the Arrow button K or L until your desired day appears.

(Example: 5th → 05)



MONTH DAY YEAR

0 5 / 0 5 – – – – – – –

HOUR MINUTE

– – : – – – –

- 15 EN

1C29

5

Select the year

Press the Arrow button K or L until your desired year appears.

(Example: 2005)

Then press the Arrow button B .

6

Select the hour

Press the Arrow button K or L until your desired hour appears.

(Example: 5, PM)


7

Select the minute

Press the Arrow button K or L until the desired minute appears.

(Example: 40)


MONTH DAY YEAR

0 5 / 0 5 THU 2 0 0 5

HOUR MINUTE

– – : – – – –


MONTH DAY YEAR

0 5 / 0 5 THU 2 0 0 5

HOUR MINUTE

0 5 : – – PM


MONTH DAY YEAR

0 5 / 0 5 THU 2 0 0 5

HOUR MINUTE

0 5 : 4 0 PM

AUTOMATIC CLOCK SETTING

Make sure ...


• Confirm the unit is receiving a RF (Radio

Frequency) signal from either an antenna or cable system connection using the ANT. terminal on the rear of the unit.

NOTE:

• If a cable converter box is being used, make sure it is powered on.

• You must use the unit’s remote control to perform the clock setting procedure.

• If the unit is connected directly to a cable converter box or satellite box, the local PBS station must be selected on the cable box itself, and the unit must be set to the output channel of the cable converter box or satellite box (usually channel 3 or 4), to be able to set up or correct the clock automatically.

8

Start the clock


Although seconds are not displayed, they begin counting from 00 when you press the SETUP button on the remote control. Use this feature to synchronize the clock with the correct time.

5:40 PM

NOTE:

When unplugging the AC cord or if there is a power failure for more than 3 seconds, you may have to reset the clock.

1



Press the Arrow button K or L to select “SETTING CLOCK”.

Press the ENTER button to enter

“SETTING CLOCK” menu.

2

Set “AUTO CLOCK” to [ON]

Press the Arrow button B until

“AUTO CLOCK [ON]” appears.

B

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH


B AUTO CLOCK [ON]


AUTO CLOCK CH [ 02 ]

MANUAL CLOCK SET

D.S.T.

[OFF]

TO CHANGE CLOCK SETTING

If you want to change the clock,

1) Follow steps [1] and [2].

2) Select where you want to change using the Arrow button B .

3) Enter correct numbers using the Arrow button K or L .

4) Press the SETUP button on the remote control to start the clock.

PLEASE NOTE:

If there is no local PBS station in your area or on your cable system, select “AUTO CLOCK” and press the ENTER button to turn [OFF] this function.

Then you can manually adjust the clock.

- 16 -

3

Begin “AUTO CLOCK CH SEARCH”

Press the Arrow button L to select

“AUTO CLOCK CH SEARCH”.


Press the ENTER button.

• The unit begins to search for the stations which contain the auto

AUTO CLOCK [ON]

B AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

[ 02 ]

D.S.T.

[OFF] clock set signal. The search for a signal may take up to 20 seconds per channel.

• When the search has ended,“_ _” appears at the lower left of the

– AUTO CLOCK CH SEARCH –

08 10 13 screen.

• Write down the number(s) that appear on the screen. These are the auto clock station(s) in your

_ _ area. See step [4] on page 17.

• If no number(s) appear on the TV screen, there are no stations in your area which contain the Auto

Clock signal. Auto Clock Setting is not possible.

Please use Manual Clock Setting on page 17.

Press the SETUP button to exit the screen.

NOTE: During Auto Clock CH Search, the picture may be distorted. This is normal.

EN

1C29

4

Enter the channel number that contains the

Automatic Clock Setting Signal


Press the Arrow button K or L to select “SETTING CLOCK”.

Press the ENTER button to enter

“SETTING CLOCK” menu.

Press the Arrow button K or L to select “AUTO CLOCK CH”.

B

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH


Press the ENTER button or the

Arrow button { or B until you locate auto clock station number which you wrote down in step [3] on page 16.

AUTO CLOCK [ON]

B


AUTO CLOCK CH

MANUAL CLOCK SET

[ 45]

D.S.T.

[OFF]

Press the SETUP button to exit the screen.

DAYLIGHT-SAVING TIME

TV/VCR

Select this feature and the unit’s clock automatically will advance one hour in April, then reverse one hour in October.

When Daylight-Saving Time is ON, the clock will change automatically as follows:

•

First Sunday of April : At 2 AM the clock immediately changes to 3 AM. Any timer programming you have set to occur between 2 AM and 3 AM will not record.

•

Last Sunday of October : At 2 AM the clock immediately changes to 1 AM.

Make sure ...


5

Turn off the unit

Once the unit is turned off , it will periodically check and set the correct date and time.

1



Press the Arrow button K or L to point to “SETTING CLOCK”.

Then, press the ENTER button.

- TV/VCR SETUP -

TIMER PROGRAMMING

B SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

2

Set “D.S.T.” (Daylight-Saving Time) to [ON]

Press the Arrow button K or L to point to “D.S.T.”.


Then, press the ENTER button until

[ON] appears.

AUTO CLOCK [ON]


AUTO CLOCK CH

MANUAL CLOCK SET

B D.S.T.

[ 02 ]

[ON]

3

Exit the Daylight-Saving Time mode


TO CANCEL THE DAYLIGHT-SAVING

TIME

Repeat steps [1] to [2], and select [OFF] using the

ENTER button.

- 17 EN

1C29

CHANNEL SET UP

TV/VCR

You can program the tuner to scan all the channels you receive in your area.

NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just select the unit’s channel selector to the output channel of the cable box or satellite box (Ex

CH3). Then select the channel to be viewed on the

Cable Box or Satellite Box.

Make sure ...


1

Select “CHANNEL SET UP”


Press the Arrow button K or L to point to “CHANNEL SET UP”.


- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

B CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

2

Begin auto ch programming

Press the Arrow button K or L to point to “AUTO CH PROGRAM-

MING”.


The tuner scans and memorizes all the active channels in your area.

– CHANNEL SET UP –

ADD / DELETE CH (CATV)

B AUTO CH PROGRAMMING

3

After scanning

The tuner stops on the lowest memorized channel.

• When AUTO CH PROGRAMMING is activated where there is no TV signal input, “NO TV SIG-

NALS” will appear on the display after the completion of the channel scanning.

• The unit may recognize CATV channels to be TV channels by the receiving conditions. In this case, try auto ch programming again in the fine receiving conditions.

DELETING (OR ADDING)

CHANNEL

TV/VCR

The channels you no longer receive or seldom watch can be deleted from the memory. (Of course, you can add the deleted channel into the memory again.)

1

Select “CHANNEL SET UP”


Press the Arrow button K or L to point to “CHANNEL SET UP”.


- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

B CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

2

Select “ADD/DELETE CH”

Press the Arrow button K or L to point to “ADD/DELETE CH”.

Press the ENTER button.

– CHANNEL SET UP –

B ADD / DELETE CH (CATV)

AUTO CH PROGRAMMING

3

Enter the desired channel number

Press the Arrow button K or L until your desired channel number appears. (You can also use the number buttons or the CHANNEL button K or L to enter it)

ADD / DELETE

08

(Example: CH8)

• When selecting cable channels which are higher than 99, press the +100 button first, then, press the last two digits. (Example: to select channel 125, first press the +100 button then press “2” and “5”).

• You must proceed single-digit channel numbers with a zero (Example: 02 ... 09).

4

Delete (or add) it from (into) memory

Press the ENTER button. The channel number changes to light red. The channel is deleted from memory.

• To delete another channel, repeat steps [3] and [4].

• If you press the ENTER button again, the channel is memorized again.

Added channel: Light blue.

Deleted channel: Light red.

5

Exit the channel setup mode

Press the SETUP button on the remote control to returns to TV mode.

NOTE: To confirm that channel(s) has been deleted or added, press the CHANNEL button K or L .

- 18 EN

1C29

TV OPERATION

WATCHING A TV PROGRAM

1

Turn on the unit

Press the POWER button to turn on the unit.

2

Select the channel number

Press the CHANNEL button K or L to select your desired channel number or press the number on the remote control.

Note for using the Number button on the remote control:

¡ When selecting cable channels which are higher than 99, press +100 first, then press the last two digits. (Example: to select channel 125, first press

“+100” then press “2” and “5”).

¡ You must preced single-digit channel numbers with a zero (For example: 02, 03, 04 and so on).

Remember: If the unit is connected to a cable box or satellite box, the unit must be on CH3 or CH4, then the channel to be viewed must be selected on the cable box or satellite box.

3

Adjust sound

Press the VOLUME button X or Y to adjust the volume.

VOLUME 20

C C C C C

C C C C C C C

NOTES:

• If you press the CHANNEL button K or L in the

DVD mode, you can change the TV channels.

Even if you turn off the unit in the DVD mode, when you turn it on again, it will go into the

TV/VCR mode.

DEGAUSSING

TV/VCR

TV/VCR

Magnetism from nearby appliances and speakers might affect the color of the TV picture.

If this happens, move this unit away from the appliance. If the color is still not correct, unplug the power cord, then plug it in again 30 minutes later or so.

2

PICTURE CONTROL

Select item you want to adjust

BRIGHT

CONTRAST

COLOR

TINT

SHARPNESS

– P

TV/VCR

The unit’s picture controls – BRIGHT, CON-

TRAST, COLOR, TINT and SHARPNESS – are preset to factory specifications. Although they are usually the best, you may need to make some further adjustments for a natural looking image.

NOTES:

• Procedures must be followed within 5 seconds or the Picture Control mode will be cancelled.

• When setting the Picture Control, the Game mode will be cancelled.

Make sure ...


1

Select “PICTURE CONTROL”

Press the PICTURE button on the remote control.

Press the Arrow button K or L until desired control is displayed.

BRIGHT

3

Adjust the picture control

Press the Arrow button s or B to adjust to your desired level.

BRIGHT

Arrow Button { to decrease brightness

Arrow Button B to increase brightness

CONTRAST to decrease contrast to increase contrast

COLOR

TINT

SHAPNESS to pale to purple to soft to brilliant to green to clear

• Even if there is a power failure of any kind, the unit will retain its memory for this feature.

P +

- 19 EN

1C29

CLOSED CAPTION SYSTEM

TV/VCR

You can view specially labeled (cc) TV programs, movies, news, pre-recorded tapes with either a dialogue caption or text display.

CAPTION mode: By choosing the caption mode, you can watch dramas, movies and news while captioning the dialogues and the contents of news.

TEXT mode: By choosing the text mode, you can watch half screen text information if you want.

1-2: You may get these captions or text information by selecting either “1” or “2”. Caption “2” is used, usually for a second language if available.

Make sure ...


1

Select “CAPTION”


Press the Arrow button K or L to point to “CAPTION”.

B

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

2

Select your desired caption menu

Press the ENTER button until your desired caption menu appears.

([CAPTION1], [CAPTION2],

[TEXT1] or [TEXT2])

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

B CAPTION [CAPTION1]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

NOTE:

Not all programs are broadcast with closed captions.

This unit is designed to provide error free closed captions from high quality antenna, cable and VCR signals. Conversely, poor quality signals are likely to result in caption errors or no captions at all. Common signal conditions which may cause captions errors are listed below:

• Automobile ignition noise

• Electric motor brush noise

• Weak snowy reception on TV screen

• Multiplex signal reception displaying picture ghosts or airplane flutter.

• Playback of poorly recorded or worn VCR tapes.

NOTE:

If the unit displays a black box on the TV screen, this means that the unit is set to the TEXT mode. To clear screen, select [CAPTION1],

[CAPTION2] or [OFF].

3

Exit the caption setting mode


TO CANCEL THE CLOSED CAPTION

SYSTEM

Repeat steps [1] and [2], and select [OFF] using the

ENTER button. Press the SETUP button on the remote control to return to TV mode.

WHEN THE CLOSED CAPTION MODE

IS ON

The On-Screen Display will disappear after 5 seconds.

• It will also disappear when the MUTE button is pressed, and when the PAUSE button is pressed while recording.

• Even if there is a power failure of any kind, the unit will retain its memory for this feature.

- 20 EN

1C29

V-CHIP SET UP

TV/VCR

V-CHIP SET UP

Make sure ...


1

Select “V-CHIP SET UP”


Press the Arrow button K or L to select “V-CHIP SET UP”.


2

Enter Access code

Use the number buttons on the remote control to enter the access code.

• For the first time set-up or in the event the unit has lost power, enter the default code of 0000.

3

Select “TV RATING”

Press the Arrow button K or L to select “TV RATING”.


- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

B V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

ACCESS CODE

_ _ _ _

– V-CHIP SET UP –

B TV RATING

MPAA RATING

CHANGE CODE

V-CHIP SET UP SUB RATINGS

When you select the ratings of TV-Y7,TV-PG,TV-14 or TV-MA, you will have the option of selecting sub rating categories.

1



Press the Arrow button K or L to select “V-CHIP SET UP”. Then press the ENTER button.

B

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

2


Use the number buttons on the remote control to enter the access code. (Default code is 0000.)

ACCESS CODE

_ _ _ _

3

Select “TV RATING”

Press the Arrow button K or L to select “TV RATING”.



B TV RATING

MPAA RATING

CHANGE CODE

4

Blocking TV programs

Press the Arrow button K or L to select “TV rating” that you wish to block.

Press the ENTER button to set it

B TV–Y

TV–Y7 (

TV–G

TV–PG (

TV–14 (

TV–MA (

)

)

)

)

[VIEW]

[VIEW]

[VIEW]

[VIEW]

[VIEW]

[VIEW]

[BLOCK].

• When you select the rating category and set it [BLOCK], the higher rating will change to [BLOCK] automatically. Also, the lower rating will change to [VIEW] automatically.

• When you set “TV-Y” to [VIEW], all ratings will change to [VIEW] automatically.

Selection

TV-Y

Rating Category Explanations

Appropriate for all children

TV-Y7 Appropriate for children seven and older

TV-G General Audience

TV-PG Parental Guidance suggested.

TV-14 Unsuitable for children under 14

TV-MA Mature audience only

4

Selecting Sub-Ratings

Press the Arrow button L to select the sub-rating you wish to block. Then, press the ENTER button twice.

• When you select [TV-Y7]:

Press the Arrow button L or K to

TV–Y7 [BLOCK] select “FV” (Fantasy Violence).

Then press the ENTER button to select [BLOCK] or [VIEW].

B FV [BLOCK]

• When you select [TV-PG], [TV-14] or [TV-MA]:

Press the Arrow button L or K to select “D”(Suggestive Dialog),

TV–PG [BLOCK]

“L”(Coarse Language),

“S”(Sexual Situation), or

B D

L

S

V

[BLOCK]

[BLOCK]

[BLOCK]

[BLOCK]

“V”(Violence). Then press the

ENTER button to select

[BLOCK] or [VIEW].

Note: When you select [TV-MA], “D” does not appear on the TV screen.

• The sub-ratings which set to

[BLOCK] appears next to the rating category in the TV rating menu.

TV–Y

TV–Y7 (

TV–G

)

B TV–PG (DLSV )

TV–14 (DLSV )

TV–MA ( LSV )

[VIEW]

[VIEW]

[VIEW]

[BLOCK]

[BLOCK]

[BLOCK]

5

Exit the V-Chip setting mode

Press the SETUP button on the remote control to enter the setting and exit the screen.

5


Press the SETUP button on the remote control to exit the screen.

- 21 EN

1C29

CHANGING V-CHIP BLOCKED PRO-

GRAMMING

Note: To change the rating, the TV must be turned to a station that is not protected. If the (PROTECTED) appears on the screen, please change the channel to a station that is not protected.

1)Follow steps [1] and [2].

2)Press the Arrow button K or L to select “TV RAT-

ING”. Then press the ENTER button. Select a TV rating to be unblocked by pressing the Arrow button K or L .

Then press the ENTER button to unblock the rating.

3)Press the SETUP button on the remote control to exit the screen.

MPAA RATING SET UP

1



Press the Arrow button K or L to select “V-CHIP SET UP”. Then press the ENTER button.

2



B

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

ACCESS CODE

_ _ _ _

• When you set “G” to [VIEW], all ratings will change to [VIEW] automatically.

5



CHANGE ACCESS CODE

To change access code, follow the steps below.

1



Press the Arrow button K or L to select “V-CHIP

SET UP”.


2



The default code is 0000.

3

Select “CHANGE CODE”

Press the Arrow button K or L to select "CHANGE CODE". Then press the ENTER button.

ACCESS CODE

_ _ _ _


TV RATING

MPAA RATING

B CHANGE CODE

3

Select “MPAA RATING”

Press the Arrow button K or L to point to “MPAA RATING”.



TV RATING

B MPAA RATING

CHANGE CODE

4

Enter New code

Use the number buttons to enter your desired access code in the

NEW CODE space. Then enter the same code in the CONFIRM

CODE space. V-CHIP SET UP screen appear on the screen.

• If you enter wrong code, repeat step [4], making sure you enter the same new code exactly in the confirm code space.

NEW CODE

X X X X

CONFIRM CODE

_ _ _ _

4

Select your desired item

Press the Arrow button K or L to point to your desired item.

Then press the ENTER button to select [BLOCK] or [VIEW].

G

PG

PG–13

B R

NC–17

X

[VIEW]

[VIEW]

[VIEW]

[BLOCK]

[BLOCK]

[BLOCK]

Selection

G

Rating Category Explanations

General Audience

PG Parental Guidance suggested.

PG-13 Unsuitable for children under 13

R Restricted; under 17 requires accompanying parent or adult guardian

NC-17 No one under 17 admitted

X Mature audience only

• When you select the rating category and set it

[BLOCK], the higher rating will change to

[BLOCK] automatically. Also, the lower rating will change to [VIEW] automatically.

- 22 -

5



Note: If you unplug the power cord or power failure occurs, the changed access code will be lost and will return to default (0000). Change your access code again as necessary.

EN

1C29

MTS (Multi-Channel Television sound) SYSTEM

You can record or listen to a program in MTS stereo.

4)

PLAY B

HIFI

CHECKING THE SELECTED MTS MODE

When you play a VHS tape, or receive a broadcast on the unit’s tuner channel you are watching, the status shown below will appear when you press the

DISPLAY button on the remote control.

12:00AM

CH 123

STEREO/SAP

SP COUNT 0:00:00

3)

2)

1)

SAP

Second Audio Program, which means your program, can also be received in a second language or sometimes a radio station.

HIFI

High Fidelity which produces better sound than standard stereo TV/VCR/DVDs.

TV/VCR

1) When a program is broadcast in stereo,

“STEREO” appears on the TV screen.

2) When a program is broadcast in second audio,

“SAP” appears on the TV screen.

3) When a program broadcast both in stereo and second audio, “STEREO” and “SAP” appear on the

TV screen.

NOTE: Although a program may be broadcast in both stereo and second audio, you cannot record in both stereo and second audio at the same time.

4) While the unit is set in HIFI stereo mode and playback mode. “HIFI” appears on the TV screen.

While the unit is set in monaural (MONO) mode,

“HIFI” disappears from the TV screen.

NOTE: If you play non-HIFI tapes while the unit is set in “HIFI”, “HIFI” will disappear from the

TV screen and the unit will play automatically in monaural.

MTS RECORDING/MONITOR MODE

Type of broadcast Display on STEREO/SAP

Regular the TV screen SELECTION

-None-Invalid-

(monaural audio)

Stereo broadcast

Bilingual broadcast

STEREO

SAP

-Invalid-

STEREO*

TV/VCR

Hi-Fi audio track (2-channel) Normal audio

L-channel

Mono

R-channel

Mono track

Mono

Stereo & Bilingual STEREO broadcast SAP

SAP*

STEREO*

SAP*

L

Main audio program

Sub audio program

L sub audio program

R

Main audio program

Sub audio program

R sub audio program

L+R

Main audio program

Sub audio program

L+R sub audio program

* You must select the recording mode in TV AUDIO [STEREO] or [SAP] when you record a broadcast.

- 23 EN

1C29

Make sure ...


TO SELECT HIFI MODE

1

Select “USER’S SET UP”


Press the Arrow button K or L to point to “USER’S SET UP”. Then press the ENTER button.

2

Select“VCR AUDIO”

Press the Arrow button K or L to point to“VCR AUDIO”.

3

Select [HIFI]

Press the ENTER button until

[HIFI] appears.

SELECTING THE MTS SYSTEM

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

B USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

– USER’S SET UP –

RENTAL

REPEAT PLAY

AUTO RETURN

B VCR AUDIO

TV AUDIO

[OFF]

[OFF]

[OFF]

[HIFI]

[STEREO]


RENTAL

REPEAT PLAY

AUTO RETURN

B VCR AUDIO

TV AUDIO

[OFF]

[OFF]

[OFF]

[HIFI]

[STEREO]

TV/VCR

TO SELECT MONO MODE

You can change the selection to “MONO” if you want to listen to HIFI tapes in normal audio playback.

1) Press the SETUP button on the remote control.

Press the Arrow button K or L to point to “USER’S

SET UP”. Then press the ENTER button.

2) Press the Arrow button K or L to point to

“VCR AUDIO”.

3) Press the ENTER button until [MONO] appears.

4) Press the SETUP button on the remote control to return to TV mode.

TO SELECT STEREO, SAP, OR MONO

1



Press the Arrow button K or L to point to “USER’S SET UP”.

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

B USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

2

Select “TV AUDIO”

Press the Arrow button K or L to point to“TV AUDIO”.

4

To return to TV mode



RENTAL

REPEAT PLAY

AUTO RETURN

VCR AUDIO

B TV AUDIO

[OFF]

[OFF]

[OFF]

[HIFI]

[STEREO]

NOTES:

•

Normally, “HIFI” should be selected for playback with HIFI sound.

• When you play non-HIFI tapes, the unit will play automatically in the monaural mode.

•

The unit records automatically MTS broadcasts in

HIFI stereo sound unless you select SAP mode recording before you begin recording.

3

Select [STEREO], [SAP], or [MONO]

Press the ENTER button until [STEREO], [SAP] or

[MONO] appears.

4

To return to TV mode


NOTES:

•

You must select the recording mode,either TV

AUDIO [STEREO] or [SAP] when you record a broadcast.

Refer to “MTS RECORDING/MONITOR

MODE”.

•

If you select [SAP] when second audio is not available, the unit will record normal audio.

• The unit records automatically MTS broadcasts in

HIFI stereo sound unless you select SAP mode recording before you begin recording.

- 24 EN

1C29

VIDEO CASSETTE

This unit will operate with any cassette that has the mark. For best results, we recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.

PRECAUTIONS

• Avoid moisture. Moisture condensation may occur on the tape if it is moved from a cold place to a warm place or visa versa. Before using a tape with these conditions, to avoid damage of the tape and your unit, wait until the tape has warmed to room temperature and the moisture has evaporated.

• Avoid extreme heat, high humidity and magnetic fields.

• Do not tamper with the cassette mechanism.

• Do not touch the tape with your fingers.

INSERTING A CASSETTE

Insert the cassette in the direction as shown. Push in gently, but continuously, on the center-back of the cassette until it is drawn into the unit. The unit will automatically be turned on.

Window

CORRECT WRONG

TWO DIFFERENT TAPE SPEEDS

Before recording, select the tape speed from : SP mode (Standard Play) or SLP mode (Super Long

Play).

The table below shows the maximum recording/playback time using T60, T120 or T160 tapes in each mode.

Tape Speed Recording/Playback Time

Type of tape T60 T120 T160

SP mode

SLP mode

1 hour

3 hours

2 hours

6 hours

2-2/3 hours

8 hours

Note: You can play back a tape recorded in LP mode

(Long Play).

REMOVING A CASSETTE

1)In the Stop mode, press the STOP/EJECT button on the front panel. The cassette will be ejected.

2)Pull the cassette out of the cassette compartment.

3)Store the cassette in its case as shown.

ERASE PREVENTION

You can prevent accidental erasing of recording by breaking off the tab on the back edge of the cassette.

Tab

If you decide to record on the tape again, cover the hole with plastic tape.

- 25 -

Transparent Tape

NOTE:

• In DVD mode, Whether the cassette is with tab or without tab you insert, it doesn’t start playing until you press the PLAY button.

In TV/VCR mode, if th cassette without tab is inserted, playback will automatically start.

EN

1C29

PLAYBACK

NORMAL PLAYBACK

TV/VCR

Make sure ...


1

Insert a prerecorded tape

If the erase-protection tab has been removed, the unit will start playback automatically.

2

To begin playback

Press the PLAY button.

PLAY B

SLOW MOTION

TV/VCR

Press the PAUSE button, then press the F.FWD button to start the playback in slow motion. The unit mutes the sound during slow motion. Press the PLAY button to return to normal playback.

NOTE: If it is left in the Slow mode for more than 5 minutes, the unit will automatically go into the Stop mode.

3

To stop playback

Press the STOP button when playback is completed.

STOP

NOTES:

•

If you press the PLAY button (of the TV/VCR side) in the DVD mode, you can start the VCR playback.

•

If you press the SELECT button during the VCR playback, it will stop and the mode will change to the DVD mode. In addition, the same function operates with the DVD side PLAY button or the

OPEN/CLOSE button.

TRACKING ADJUSTMENT

TV/VCR

• Tracking adjustment will be set automatically

(Digital Tracking function) when you start playback.

• However when playing pre-recorded tapes or tapes recorded on other VCR, noise lines (black and white streaks) may appear on the playback picture.

If this occurs, you can adjust the tracking control manually by pressing the CHANNEL button K or

L until the streaks disappear. To return to the DTR function, stop the tape once and start playback again.

• You can reduce the noise lines by pressing the

CHANNEL button K or L in slow mode, too.

Tracking adjustment in Slow mode will not be set automatically.

STILL PICTURE

TV/VCR

You can view a still picture on the TV screen during playback (the Still mode). Press the PAUSE button during playback. Only tapes recorded in the SLP mode will show the least amount of lines.Press the

PLAY button to return to playback.

NOTES:

• You can advance the picture one frame at a time by pressing the PAUSE button during the Still mode.

• If it is left in the Pause mode for more than five minutes, the TV/VCR/DVD will automatically switch to the Stop mode.

VERTICAL HOLD CONTROL

TV/VCR

In the Pause/Still mode only, when the picture begins to vibrate vertically, stabilize the picture by pressing the CHANNEL button K or L .

NOTE:

If there are video noise lines on the screen, see

TRACKING ADJUSTMENT section on this page.

- 26 EN

1C29

Make sure ...


• Insert a prerecorded tape.

RENTAL PLAYBACK

TV/VCR

This function enables you to improve the picture quality when playing back worn cassettes such as rented tapes.

1





SPECIAL PLAYBACK

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

B USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

AUTO REPEAT PLAYBACK

TV/VCR

This unit has the auto repeat function that allows you to repeat a tape indefinitely without touching the

PLAY button.

ALL REPEAT: Repeat playback from the beginning to the end of the tape.

BLANK REPEAT : Repeat playback from the beginning to a blank part, which is blank for more than

10 seconds.

1





- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

B USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

2

Set “RENTAL” to [ON]

Press the Arrow button K or L to point to “RENTAL”.

Press the ENTER button until [ON] appears.


B RENTAL

REPEAT PLAY

AUTO RETURN

VCR AUDIO

TV AUDIO

[ON]

[OFF]

[OFF]

[HIFI]

[STEREO]

3

Exit the Rental setting

Press the SETUP button on the remote control to return to the TV mode.

2

Select “ALL” or “BLANK”

Press the Arrow button K or L to point to “REPEAT PLAY”.

Press the ENTER button repeatedly until your desired selection [ALL] or [BLANK] appears.


RENTAL

B REPEAT PLAY

AUTO RETURN

VCR AUDIO

TV AUDIO

[OFF]

[ALL]

[OFF]

[HIFI]

[STEREO]

3

Exit the Repeat Play setting

Press the SETUP button on the remote control to return to the TV mode.

4

Start playback

Press the PLAY button to start playback. “RENTAL

PLAY B ” appears.

• Once you select the Rental mode, it stays in effect even after you turn off the unit.

TO CANCEL THE RENTAL MODE

Repeat steps [1] and [2] and select [OFF] using the

ENTER button on the remote control. Press the

SETUP button on the remote control to return to TV mode.

Even if there is a power failure of any kind, the unit will retain its memory for this feature.

4

Start playback

Press the PLAY button to start the Repeat Play.

“REPEAT PLAY B ” appears.

• Once you select the Repeat Play mode, it stays in effect even after you turn off the unit.

• If the Rental mode is set [ON], the “RENTAL

PLAY B ” display has priority.

TO CANCEL THE REPEAT PLAY MODE

Repeat steps [1] and [2] and select [OFF] using the

ENTER button on the remote control. Press the

SETUP button on the remote control to return to TV mode.


- 27 EN

1C29

SEARCH

Make sure ...


• Insert a tape.

ZERO RETURN

TV/VCR

This function allows you to search easily a beginning point that you want to review by rewinding or fast forwarding.

NOTE:

Zero Return WILL NOT work on a blank tape or a blank portion of a tape.

1

Stop a tape at your desired point

Rewind or fast forward the tape to the beginning point at which you want to review.

TIME SEARCH

TV/VCR

The Time Search function makes it possible to quickly advance the tape to your desired position simply by entering the exact amount of playback time you want to skip.

NOTES:

• Time Search can be set up to a maximum of 9 hours 50 minutes (9:50) by 10 minutes at a time.

• This function will not operate in recording mode.

• This function is not operative when a cassette tape is not inserted in the unit.

In the example below: To watch a program before/ after 2 hour 50 minutes from the present position, in either direction.

2

Reset the counter to 0:00:00

Press the C.RESET button repeatedly.

3

Begin recording or playback

Press the RECORD or PLAY button.

Press the STOP button when recording or playback is completed.

1

Select “TIME SEARCH” mode


Press the Arrow button K or L to point to “TIME SEARCH”.


- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

B TIME SEARCH

INDEX SEARCH

4

To activate “ZERO RETURN” mode


Press the Arrow button K or point to “ZERO RETURN”.

L to

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

B ZERO RETURN

TIME SEARCH

INDEX SEARCH Then, press the ENTER button.

The counter will appear on the TV screen.

The tape will automatically stop when the counter returns to 0:00:00.

2

Enter your desired time

Press the Arrow button K or L until your desired time appears.

(Example: “2:50” stands for 2 hours

50 minutes)

TIME SEARCH

2 : 50

If you wish to cancel the Time

Search at this point, press the SETUP button on the remote control.

PICTURE SEARCH

TV/VCR

This feature is very useful in finding or skipping over a particular scene on a tape. In this mode, the sound will be muted.

1)You may view a video tape at a high speed in either a forward or reverse direction by pressing the F.FWD or REW button during playback. (in the SP / LP / SLP modes)

NOTE:

• If you press the F.FWD or REW button on the front panel in the DVD mode, the VCR forward or reverse will start. Please press the STOP/EJECT button once to stop it, twice to eject it.

2)Press it again and the unit will begin to search in super high speed. (in the LP / SLP modes only)

NOTE:

• Tapes recorded in the SP or LP mode will display a noise bar on the TV screen and the picture may revert to Black and White. This is normal.

3)Press the PLAY button to return to normal speed.

- 28 -

3

Begin Time Search

By pressing the Arrow button s or B , the unit will rewind or fast forward to the specified point.

The time counts down as the searching progresses.

When 0:00 is reached, the tape will start playback automatically.

TO CANCEL THE TIME SEARCH

Press the STOP/EJECT button on the front panel or the STOP button on the remote control. This will delete the selected time.

EN

1C29

INDEX SEARCH

TV/VCR

This feature provides a method of indexing the starting point so that it can be easily returned to in either fast forward or rewind mode.

• The index mark will be made automatically when the REC button is pressed. It will also be marked at the starting point of Timer recording and OTR.

• The index mark will not be recorded if the PAUSE button is pressed and released during recording.

• The time gap between making the index marks on the tape should be greater than 1 minute for SP recording, 2 minutes for LP recording and 3 minutes for SLP recording.

• In some cases, the index mark at the beginning of video tape cannot be detected.

Example: You are watching program number 4 and want to fast forward to program number 7. You must skip three programs.

1

Select “INDEX SEARCH”


Press the Arrow button K or L to point to “INDEX SEARCH”. Then press the ENTER button.

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

B INDEX SEARCH

2

Enter your desired number

Press the Arrow button K or L until the number of programs that you want to skip appears.

(Example: “03” for 3 programs)

INDEX SEARCH

0 3

• The Index Search mode will be canceled if the procedures are not activated in 30 seconds.

3

Begin Index Search

Press the Arrow button s or B . The unit begins rewinding or fast forwarding to the beginning of desired program.

NOTE: Every time an index signal is skipped, the number in the program indicator decreases by one.

CURRENT PLAYBACK PROGRAM

Beginning of tape End of tape

4

Pro.1

Pro.2

Pro.3

Pro.4

Pro.5

Pro.6

Pro.7

3 2 1 1 2 3

INDEX MARK

4

After Index Search

When the preset program is reached, the unit will start playback automatically.

• The number of Index Searches can be set up to 20.

• This function will not operate in the recording mode.

• When you want to cancel the Index Search while in progress, press the STOP button.

SPECIAL FEATURES

REAL TIME TAPE COUNTER

TV/VCR

This shows the elapsed recording or playback time in hours, minutes, and seconds. (The displayed time will not change on a blank tape or blank portions on the tape.)The “–” indication will appear when the tape has rewound further than “0:00:00” on the tape counter.

AUTO REWIND-EJECT

TV/VCR

• When the end of a tape is reached during recording, playback, or fast-forward, the tape will automatically rewind to the beginning. After rewinding finishes, the unit will eject the tape and turn itself off.

• This function is available when Repeat Play is set to [OFF].

• The tape will not auto-rewind during timer recording or One Touch Recording.

- 29 EN

1C29

RECORDING

Make sure ...


• Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording.)

NOTES:

• This unit will ONLY record and view the same channel.

• This unit cannot record the contents from the built-in DVD.

NORMAL RECORDING

TV/VCR

You can ONLY watch the same TV program that is being recorded.

1

Select the channel to be recorded

Press the number buttons on the remote control or the CHANNEL button K or L .

CH 10

NOTE: If the unit is connected to a cable box or satellite box, the unit must be on CH3 or CH4, then the channel to be recorded must be selected on the cable box or satellite box.

2

Select the tape speed

Press the SPEED button to select the desired tape speed (SP/ SLP).

SP

SKIPPING UNWANTED

SCENES DURING RECORDING

TV/VCR

Press the PAUSE button to temporarily stop recording.

Press the PAUSE or RECORD button to resume recording.

PAUSE

NOTES:

SP

• After five minutes, the unit will automatically switch to the Recording mode to prevent tape damage.

• If “CLOSED CAPTION (ON)” is selected, the On-

Screen Display will appear for 5 seconds, then disappear.

3

Begin recording

Press the RECORD button.

REC

SP

4

Stop recording

Press the STOP button when recording is completed.

- 30 EN

1C29

OTR (One Touch Recording)

TV/VCR

This function enables you to set a recording length simply by pressing the REC/OTR button on the front panel.

Make sure ...



NOTES:

• You CANNOT start OTR with the remote control.

• Recording starts immediately when the REC/OTR button is pressed.

• When the REC/OTR button is pressed 18 times, the unit returns to the Normal Recording mode.

• To stop the OTR operation, press the STOP button.

• To show the remaining time, press the DISPLAY button on the remote control so that “OTR” appears on the TV screen. (It will show up momentarily then disappear.)

• Recording stops when 0:00 is reached.

• Please note that in the SLP mode maximum recording time, assuming the tape is started at the beginning, is 8 hours using T-160 (or 6 hours using T-120).

• If the tape runs out before the end time, the unit will switch to the Stop mode immediately, ejects the tape and turns itself off.

• If you press the POWER button during OTR, the unit continues recording.

1

Select the channel to be recorded

Press the number buttons on the remote control or the CHANNEL button K or L .

NOTE: If the unit is connected to a cable box or satellite box, the unit must be on CH3 or CH4, then the channel to be recorded is selected on the cable box or satellite box.

2

Select the tape speed

Press the SPEED button to select the desired tape speed (SP/ SLP).

3

Begin OTR

Press the REC/OTR button on the front panel as many times as needed. The recording length will be

OTR(2 : 30) determined by the number of times you press the REC/OTR button.

SP

Each additional press will increase the recording time by 30 minutes up to 8 hours.

Push(es) Display

1 push

2 pushes

3 pushes

0:30

1:00

Recording length

(normal recording)

30 minutes

60 minutes

17 pushes 8:00 480 minutes

COPYING A VIDEO CASSETTE

(Requires a VCR or camcorder)

TV/VCR

You can make copies of video tapes made by friends or relatives for your enjoyment.

You can not copy a DVD to a videotape.

WARNING: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws.

Connect this unit and a source (playing) VCR using the following diagram.

[This unit] [Fig.8]

[Ex: Source (playing)

VCR or camcorder]

Audio/Video adapter cable

(not supplied)

AUDIO

L

OUT IN

R

VIDEO

OUT IN

1)Insert a pre-recorded video cassette into the source

VCR or camcorder.

2)Insert a blank video cassette, or one you want to record over, into the cassette compartment.of the unit.

3)Press the SPEED button on remote control for the unit to select the desired recording speed (SP/SLP).

4)Press the CHANNEL button K or L on the front panel until “AUX” appears on the screen.

5)Press the RECORD button on the unit.

6)Begin playback of the tape in the source VCR or camcorder.

NOTE: For best results during copying, use the front panel controls of the unit whenever possible. The remote control might affect the source VCR’s playback operation.

7)To stop copying, press the STOP/EJECT button on the unit, then stop the tape on the source VCR or camcorder.

- 31 EN

1C29

TIMER RECORDING

AUTOMATIC TIMER

RECORDING

TV/VCR

You may set the unit to start and end a recording while you are away. You can set 8 programs to record on specific days, daily or weekly within a 1 year period.

In the example below, the timer is being set to record:

DATE: July 10th, 2005

SETTING TIME: from 7:30PM to 8:50PM

CHANNEL: CH61

TAPE SPEED: SP

Make sure ...

• If a cable box or satellite box is connected to the unit, you will be limited to record only one channel. And the channel selector on the unit must be selected to the output channel of the boxes CH 3 or

CH 4 and then the actual channel to be recorded must be selected on the boxes.

• Clock must be set to the correct time and date before setting the timer.

• The unit must be turned on to program it.


• The channel you want to record is properly set in advance. (See page 16.)

Avoid over lap of programs ...

There is a chance that a program will not be recorded. when programs overlap;

• The program with an earlier start has priority.

• Once the earliest program finishes, the overlapping programs will begin recording in sequence.

• If the starting time is the same, the program in the highest position on the list has priority.

• The illustration below demonstrates the sequence of recordings.

Program 1

Program 2

Program 3

10:00AM - 11:00AM

9:00AM - 10:00AM

9:30AM - 12:00PM

Recording Sequence

Program 1

10:00AM-11:00AM

Program 2

9:00AM-10:00AM

Program 3

9:30AM-12:00PM

9:00AM 10:00AM 11:00AM

*Recording period is SHADED

12:00PM

1

Select “TIMER PROGRAMMING”


Confirm “TIMER PROGRAM-

MING” is pointed by pressing the

Arrow button K . And press the

ENTER button.

- TV/VCR SETUP -

B TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

• If you have not yet set the clock, “MANUAL

CLOCK SET” appears. If so, follow steps [3] to [8] on pages 15 and 16. Then set the timer recording.

2

Select your desired program position (1~8)

Press the Arrow button K or L to select the desired program position.


– TIMER PROGRAMMING –

CH DATE

B

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

BEGIN END

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

3

Set the channel number

Press the Arrow button K or L until the desired channel number


CH DATE BEGIN END appears. (Example: CH61)


B

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

61 -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - NOTE: If the unit is connected to a cable box or satellite box, the unit must be on CH3 or CH4, then the channel to be recorded is selected on the cable box or satellite box.

4

Select once, every day or weekly recording

For once recording :

Press the Arrow button K (up) until the desired date appears.

(Example: “7/10” for July 10th).



CH DATE BEGIN END

B

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

61 7/10 SUN -:- -

- -/- - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - For every day recording : To record a TV program at the same time on the same channel every day. (Example: Monday through

Sunday)


Press the Arrow button L (down)

CH DATE BEGIN END until “EVRY DAY” appears.


- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

B 61 EVRY DAY -:- -

- - -/- - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

For weekly recording : To record a TV program at the same time on the same channel every week.

(Example: every Monday)


Press the Arrow button L (down)

CH DATE BEGIN END until “EVRY” and your desired day of the week appear together.


B

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

61 EVRY MON -:- -

- - -/- - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

- 32 EN

1C29

5

Set beginning hour


Press the Arrow button K or L until the desired hour appears.

(Example: “ 7, PM” for 7 :30 PM )


CH DATE BEGIN END

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

P

M B 61 7/10 SUN 7:12

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

6

Set beginning minute



(Example: “30” for 7: 30 PM)

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

B 61 7/10 SUN 7:30

- -/- - - - -:- -

- -/- - - - -:- -

P

M

- -/- - - - -:- -

- -/- - - - -:- -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

-:- - - Then press the Arrow button B .

CH DATE BEGIN END

7

Set end hour


CH DATE BEGIN END Press the Arrow button K or L until the desired hour appears.

(Example: “8, PM” for 8 :50 PM )


B

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

61 7/10 SUN 7:30

P

M

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

-:- - - -

-:- - - -

-:- - - -

8:30 M - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -

8

Set end minute


(Example: “50” for 8: 50 PM)


9

Set the tape speed

Press the Arrow button K or L until the desired tape speed appears. (Example: SP)


CH DATE

B

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

61 7/10 SUN 7:30 P

M

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

BEGIN END

-:- - - -

-:- - - -

-:- - - -

8:50 P

M - -

-:- - - -

-:- - - -

-:- - - -

-:- - - -


CH DATE BEGIN END

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

B 61 7/10 SUN 7:30

- -/- - - - -:- -

P

M

- -/- - - - -:- -

- -/- - - - -:- -

- -/- - - - -:- -

-:- - - -

-:- - - -

-:- - - -

P

M 8:50 SP

-:- - - -

-:- - - -

-:- - - -

-:- - - -

TIMER PROGRAM EXTENSION

TV/VCR

To shift the time schedule of an automatic timer recording.

1)Press the POWER button.

2)Repeat step [1] on page 32.

3)Press the RECORD button and select the desired program using the Arrow button K or L .

4)Press the RECORD button again.

Each additional press will shift forward the begin/end time for recording by 10 minutes. When the recording is already in progress, each additional push will shift forward the end time only. If you want to cancel while setting, press the PAUSE button on the remote control. The recording time returns to the original time.

NOTE: When you shift forward the time schedule during recording, the recording speed will automatically be set to the SLP mode.

5)Press the ENTER or RETURN button to exit the setting menu. Then press the SETUP button on the remote control to return to original mode.

TO CORRECT A PROGRAM

• While setting a program; press the Arrow button s to go back one step and enter the correct numbers using the Arrow button K or L .

• After setting a program;


2)Repeat steps [1] to [2] on page 32.

3)Press the Arrow button B (or press the Arrow button s to go back one step) until the part you want to correct begins flashing, then make the changes pressing the Arrow button K or L .

4)Press the POWER button to set automatic timer recording.

10

Finish setting the program

Press the ENTER or RETURN button. The program is now completed.

• To set another program, repeat steps [2] to [10].

• Press the SETUP button on the remote control to return to original mode.

11

Set the timer

Press the POWER button to set automatic timer recording. The recording indicator lights up.

• You must turn off the unit to activate automatic timer recording.

If power is not turned off and you continue watching TV, “TIMER REC STANDBY” starts flashing on the TV screen 2 minutes before the programmed start time.

TO CANCEL AN AUTOMATIC TIMER

RECORDING

• After setting a program;


2)Repeat steps [1] to [2] on page 32 and select a program you want to cancel.

3)Press the C.RESET button.

4)Press the SETUP button on the remote control to return to TV mode.

• While recording is in progress;


2)Press the STOP/EJECT button on the front panel.

- 33 EN

1C29

TO CHECK THE BEGIN/END TIME

1)Press the POWER button so that the Recording indicator goes off.

2)Press the SETUP button on the remote control.

3)Confirm “TIMER PROGRAMMING” is pointed.

4)Press the ENTER button. The details of programs appear on the TV screen.

5)Press the SETUP button on the remote control to return to TV mode.

HINTS FOR AUTOMATIC

TIMER RECORDING

TV/VCR

• Make sure the channel you want to record is properly set in advance.

• It is not necessary to press the RECORD button for timer recording.

• Recording begins automatically at the Start time.

• The display will not be turned on when the programmed recording begins. To watch the currently recorded TV program or to play a DVD disc, press the POWER button to turn on the display and use the SELECT button to choose the TV/VCR mode or the DVD mode.

• The erase-prevention tab on the cassette must be in place (or you must put tape over the hole).

• If the erase-prevention tab is removed, the cassette will be ejected when the POWER button is pressed to off.

• If the tape runs out before the end time, the unit will switch to the Stop mode immediately, and the tape will be ejected.

AUTO RETURN

TV/VCR

With this feature, after timer recording is finished, the beginning of the recorded program(s) can be searched for automatically.

1





- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

B USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

2

Set “AUTO RETURN” to [ON]

Press the Arrow button K or L to point to “AUTO RETURN”.

Press the ENTER button until [ON] appears.


RENTAL

REPEAT PLAY

B AUTO RETURN

VCR AUDIO

TV AUDIO

[OFF]

[OFF]

[ON]

[HIFI]

[STEREO]

3

Auto Return will begin

When all the timer recordings are completed, the unit will rewind to the beginning of the recorded program(s).

NOTE:

• If you press the POWER button while tape is rewinding, the Auto Return will stop.

4

Watch the recorded program

Press the PLAY button.

TO CANCEL THE AUTO RETURN

MODE

Repeat steps [1] to [2] and select [OFF] using the

ENTER button.


SLEEP TIMER

TV/VCR

The Sleep Timer function turns off the unit without using the POWER button after a desired period of time.

NOTE:

• This function does not operate during Recording mode.

1

Select “SLEEP TIMER”

Press the SLEEP button on the remote control until

“SLEEP TIMER” appears.

2

Set sleep time

Press the SLEEP button until your desired sleep time appears.

Each additional push will increase the time by 30 minutes up to 120 minutes.

SLEEP 120 MINUTES

After 5 seconds, exit the Sleep Timer setting.

TO CANCEL THE SLEEP TIMER

Press the SLEEP button on the remote control until

“SLEEP TIMER” appears. Press the SLEEP button until “SLEEP 0 MINUTES” appears.

- 34 EN

1C29

ON SCREEN DISPLAY

To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:

When the Closed Caption mode is OFF:

• Counter mode: After 5 seconds, only the counter remains. To clear it, press the DISPLAY button.

• Clock mode: After 5 seconds, only the clock and the channel number remain. To clear them, press the DISPLAY button.

When the Closed Caption mode is ON:

• The On Screen Display disappear after 5 seconds.

• This is true even if the MUTE button is pressed, or the PAUSE button is pressed while recording.

OFF mode Counter mode

STOP

Clock mode

STOP 5:40PM

CH2

OFF mode Clock/Counter mode

STOP 5:40 PM

CH2

SP COUNT 0:12:34

After 5 seconds

SP

After 5 seconds

5:40PM

CH2

SP COUNT 0:12:34

COUNT 0:12:34

Counter remains

Clock & Channel remains

CABLE CHANNEL DESIGNATIONS

If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels with letters or letter-number combinations. Please check with your local cable company. The following is a chart of common cable channel designations.

CATV channel

TV Display

5A

1

2

2

3

3

4

4

5

5

6

6

7

7

8

8

9

9

10

10

11

11

12

12

13

13

A

14

B

15

CATV channel

TV Display

C

16

D

17

E

18

F

19

G

20

H

21

I

22

J

23

K

24

L

25

M

26

N

27

O

28

P

29

Q

30

CATV channel R S T U V W W+1 W+2 W+3 W+4 W+5 W+6 W+7 W+8 W+9

TV Display

CATV channel

31 32 33 34 35 36 37 38 39 40 41 42 43 44 45

W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24

TV Display 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

CATV channel W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39

TV Display

CATV channel

61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54

TV Display 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90

CATV channel

TV Display

W+55 W+56 W+57 W+58

91 92 93 94

A-5

95

A-4 A-3 A-2 A-1 W+59 W+60 W+61 W+62 W+63 W+64

96 97 98 99 100 101 102 103 104 105

CATV channel W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79

TV Display

CATV channel

TV Display

106 107 108 109 110

W+80 W+81 W+82 W+83 W+84

121 122 123 124 125

111 112 113 114 115 116 117 118 119 120

- 35 EN

1C29

DVD SECTION

ABOUT THE DISCS

PLAYABLE DISCS DISC TYPES

The following discs can be played back on this

TV/VCR/DVD.

¡ DVD video ¡ DVD-R/RW*

¡ DVD+R/RW* ¡ Audio CD

¡ CD-R/RW* ¡ MP3*

* Depending on the types or the writing method of the medium some discs can not be played.

• Some DVD-R/RW, DVD+R/RW, or CD-R/RW discs made on personal computers, or on DVD recorders may not be played back properly due to the factors such as scratches, dirt or special properties of the disc.

• Discs made on personal computers may not be played back properly due to the different environment or the settings of the application you use. We recommend always to use the standardized, rightly formatted discs.

(Please contact the sales agency for more detail).

[DVD]

Data on a DVD is divided into sections called “titles” and then into subsections called “chapters”, each of which is given a title or chapter number. Playback conditions are preset on some DVD video discs, and these playback conditions take priority over user operations on this unit. If a function you selected does not run as desired, refer to the manual accompanying the disc.

Example

Title 1 Title 2

Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2

This TV/VCR/DVD conforms to the NTSC color system.

You cannot play discs recorded in other color systems such as PAL or SECAM.

¡ Some discs include region codes as shown below.

[AUDIO CD]

Data on an Audio CD is divided into sections called

“tracks”, each of which is given a track number.

Example

Track 1 Track 2 Track 3 Track 4 Track 5 Track 6

¡ The number inside the symbol refers to a region of the world, and a disc encoded in a specific region format can only be played back on TV/VCR/DVD with the same region code.

The following discs cannot be played back on this

TV/VCR/DVD.

¡ DVD with region codes other than 1 or ALL

¡ DVD-ROM

¡ DVD-RAM (Never play back, otherwise malfunction may result.)

¡ CD-ROM

¡ VSD

¡ CDV (Only plays back the audio part.)

¡ CD-G (Only plays back the sound.)

¡ CD-I (Never play back, otherwise malfunction may result.)

¡ SACD

¡ Photo CD (Never play back, otherwise malfunction may result.)

¡ Video CD (Never play back, otherwise malfunction may result.)

Any other discs without compatibility indications

[MP3]

Data on an MP3 is divided into sections called “groups”, and then into subsections called “tracks”, each of which is given a group or track number.

Example

Group 1

Track 1 Track 2 Track 3 Track 4

Group 2

Track 5 Track 6

– 36 – EN

01A11

PLAYING A DISC

BASIC PLAYBACK

DVD-V CD MP3

GENERAL FEATURES

DVD-V

Getting started

¡ Turn on the power of amplifier and any other components, if necessary.

1 Press the POWER button.

¡ The power will turn on.

2 Press the OPEN/CLOSE button to open disc loading tray.

3 Place the chosen disc in the tray, with the label facing up.

DVD may contain menus to navigate the disc and access special features. Press the appropriate number buttons or use the Arrow button ( K / L / s

/

B

) to highlight your selection in the DVD main menu and press the ENTER button to confirm.

NOTES:

¡ Select DVD mode by pressing the SELECT button on the remote control. Then, operate the DVD functions.

¡ Unless stated, all operations described are based on remote control use. Some operations can be carried out using the menu bar on the TV screen.

DISC MENU

DVD-V

4 Press the PLAY button.

¡ The tray will close automatically and playback will then start from the first chapter or track of the disc.

If the playback does not start automatically, press the PLAY button.

¡ When you playback the DVD which a title menu is recorded, it may appear on the screen. In this case, refer to TITLE MENU section on this page.

1 Press the DISC MENU button.

¡ The DVD main menu will appear.

2 If the feature is not available, may appear on the TV screen.

symbol

3 If disc menu is available on the disc, audio language, subtitle options, chapters for the title and other options will appear for selection.

4

Press the Arrow button ( K / L / s

/

B ) to select an item, and the ENTER button to confirm selection.

5 Press the STOP button to stop playback.

TITLE MENU

NOTES

¡ When the DVD mode has been switched to the

TV/VCR mode, the DVD mode shuts down first and then TV picture and sound appears in about 4 seconds.

Similarly, when the POWER button is pressed to turn off in the DVD mode, this mode shuts down first and then the unit is turned off.

¡ A “prohibited icon” may appear at the top-right on the TV screen during operation, warning that a prohibited operation has been encountered by the DVD or the disc.

¡ With DVDs that use titles for playback program signals, playback may start from the second title, or it may skip these titles.

¡ During the playback of a two layered disc, pictures may stop for a moment. This happens when the 1st layer switches to the 2nd layer. This is not a malfunction.

1 Press the TITLE button.

¡ The title menu will appear.

2

If the feature is not available, may appear on the TV screen.

DVD-V symbol

3 Press the Arrow button ( K / L / s

/

B ) to select an item, and the ENTER button to confirm selection.

CALLING UP A MENU SCREEN

DURING PLAYBACK

¡ Press the DISC MENU button to call up the DVD menu.

¡ Press the TITLE button to call up the title menu.

NOTE:

¡ Contents of menus and corresponding menu operations may vary between discs. Refer to the manual accompanying the disc for details.

– 37 – EN

01A11

RESUME

DVD-V CD MP3

FAST FORWARD/

FAST REVERSE

DVD-V CD MP3

1 During playback, press the STOP button.

¡ Resume message will appear on the TV screen.

2 Press the PLAY button, playback will resume from the point at which playback was stopped.

¡ To cancel resume, press the STOP button twice.

¡ If the unit is turned off, resume function will be cancelled.

¡ For MP3, playback will resume from the beginning of the track at which playback was stopped.

PAUSE

1 During playback, press and hold the F.FWD

g or REV h button for a few seconds.

¡ “ g 1” or “ h 1” appears on the screen.

2 To select another speed, repeat step1 until your required speed appears on the screen.

¡ For DVDs, fast forward/reverse search speed is different depending on the disc. Approximate speed is

1 ( × 2), 2 ( × 8), 3 ( × 50) and 4 ( × 100).

¡ For audio CDs, approximate speed is × 16.

¡ For MP3, approximate speed is × 8

¡ When you use buttons on the front panel, use the

SKIP G / SEARCH g or SKIP H / SEARCH h button.

DVD-V CD MP3

1 During playback, press the PAUSE button.

¡ Playback will pause and sound will be muted.

3 To return to normal playback, press the

PLAY button.

2

To continue playback, press the PLAY button.

SLOW FORWARD /

SLOW REVERSE

DVD-V

STEP BY STEP PLAYBACK

DVD-V


¡ Playback will pause and sound will be muted.

2 The disc goes forward by one frame each time the PAUSE button is pressed.

3 To exit step by step playback, press the

PLAY button.


2 Press and hold the F.FWD g or REV h button for a few seconds.

¡ “ 1” or “ 1” appears on the screen.

3 To select another speed, repeat step2 until your required speed appears on the screen.

¡ Slow forward or reverse speed varies with the disc.

Approximate speed is 1 (1/16), 2 (1/8) and 3 (1/2).

¡ When you use buttons on the front panel, use the

SKIP G / SEARCH g or SKIP H / SEARCH h button.

4 To return to normal playback, press the

PLAY button.

– 38 – EN

01A11

SEARCH FUNCTION

TRACK SEARCH

CD MP3

TIME SEARCH

DVD-V CD

There are three ways to begin playback on an Audio

CD and MP3 at a specific track.

Using the Number buttons on the remote control

1 Press the Number buttons to enter the desired Track number.

¡ Playback will start at the selected track.

¡ For single digit tracks (1-9), press a single number

(eg. track 3, press 3).

¡ To play track 26, press +10, 2, 6.

Using the SEARCH MODE button

1

Press the SEARCH MODE button.

¡ The track search display appears.

2

Within 30 seconds, select a desired track number using the Number buttons on the remote control.

¡ For single digits press 0 first if the total track of the disc is more than 10.

¡ Playback will start at the selected track.

Using the SKIP H / G buttons

During playback, press the SKIP G button to move the next track. Press it repeatedly to skip subsequent tracks. Press the SKIP H button to go back to beginning of the current track. Press it repeatedly to go to the previous tracks.

¡ If the SKIP button is pressed while the playback is paused, the playback will be paused again after skipping to the next track.

NOTE:

¡ The SKIP H / G buttons are not available when playback is stopped.

1 During playback, press the SEARCH MODE button three times (CD: twice) to display the

Time Search on the TV screen.

2 Within 30 seconds, enter a desired disc time using the Number buttons on the remote control.

¡ Playback will start at the specified time.

¡ Press the CLEAR button to erase the incorrect input.

¡ When there is no need to enter a number, “0” appears automatically. For example, “ 0 : 0 - : - -” appears in the Time Search display if the total time of the disc is less than 10 minutes.

MARKER SETUP SCREEN

DVD-V CD

Use markers to memorise your favorite places on a disc.

1 Press the SEARCH MODE button four times

(CD: three times) during playback.

¡ The display screen and Markers will appear on the

TV screen.

2 Press the Arrow button ( s / B ) to select 1, 2,

3, 4, 5, 6, 7, 8, 9, or 10 and ensure that “- - -

- : - - : - -” appears in the display.

3

When you reach the desired point, press the

ENTER button.

¡ The Title or Track and elapsed playing time will appear in the TV screen.

TITLE / CHAPTER SEARCH

1 Press the SEARCH MODE button once for the Chapter search, twice for the Title search during playback.

_ /2

DVD-V

2 Enter the desired chapter/title number using the Number buttons on the remote control.

¡ Playback will start at the selected Chapter or Track.

¡ Press the CLEAR button to erase the incorrect input.

¡ For single digits press 0 first if the total title or chapter is more than 10.

– 39 –

4

To return to the Marker later, press the

SEARCH MODE button four times (CD: three times) during playback and the Arrow button ( s / B ) to choose the desired marker, then press the ENTER button.

NOTES:

¡ Opening the disc tray or turning off the power or selecting AC at step 2 and pressing the ENTER button will erase all Markers.

¡ To clear a marker, using the Arrow button ( s / B ), position the cursor on to the marker number to be cleared and press the CLEAR button.

¡ You can mark up to 10 points.

5

Press the SEARCH MODE or RETURN button to exit.

EN

01A11

SPECIAL PLAYBACK FUNCTION

REPEAT

REPEAT is available only during playback.

REPEAT TITLE / CHAPTER

DVD-V

PROGRAM

CD

You may determine the order in which tracks will play.

To activate the repeat function, press the

REPEAT button during playback.

¡ The repeat mode changes as described below every time you press the button.

CHAPTER TITLE

( current chapter repeat) ( current title repeat)

OFF

(repeat off )




TRACK

( current track repeat)

ALL

( entire disc repeat)

OFF

(repeat off )

1

In stop mode, press the MODE button.

¡ The PROGRAM screen will appear.

2 Press the Arrow button ▲ or ▼ to select a track, then press the

ENTER button.

¡ Press the CLEAR button to erase the most recently entered program.

TOTAL

NOTES

¡ Repeat Title/Chapter is not available with some scenes.

¡ The REPEAT setting will be cleared when moving to other title or chapter.

REPEAT TRACK

CD

3 Repeat step [2] until you have selected all the tracks you want to play in the program.

4 Press the PLAY button to play the programmed tracks.

NOTES:

¡ While the program is being played back, the STOP works as follows.

¡ Press the STOP button once and then the PLAY button again, playback will restart from the point where the STOP button was pressed. (Program continued)

¡ Press the STOP button twice and then the PLAY button again, playback will restart from the track in the usual way. (Program cleared)

¡ Up to 99 tracks can be entered.

¡ To erase all tracks in the program at once, select

“ALL CLEAR” at the bottom of the list at Step [2].

¡ If you like to repeat the current track in the program, press the REPEAT button repeatedly until “

TRACK” appears during playback. If you like to repeat the entire program press the REPEAT button repeatedly until “ ALL” appears during playback.

NOTES

¡ Repeat setting will be cleared when moving to other track.

¡ Repeat playback does not function during repeat A-B playback.

REPEAT A-B

DVD-V CD

¡

1 Press the REPEAT A-B button at your chosen starting point.

A- appears briefly on the TV screen.

RANDOM PLAYBACK

CD

This shuffles the playing order of tracks instead of playback in the sequence.

2 Press the REPEAT A-B button again at your chosen end point.

¡ A-B appears briefly on the TV screen, and the repeat sequence begins.

1 In stop mode, press the MODE button twice.

¡ RANDOM screen appears.

RANDOM

CD-DA TOTAL 0:45:55

RANDOM PROGRAM

- - no indication - -

PLAY 3

To exit the sequence, press the REPEAT A-

B button.

NOTES

¡ The repeat A-B section can only be set within the current title (for DVDs), or current track (for audio CDs).

¡ Repeat A-B is not available with some scenes in DVD.

¡ To cancel the A point which was set, press the

CLEAR button.

¡ Repeat A-B playback does not function during title, chapter, track or all repeat playback.

2 Press the PLAY button to start random playback.

NOTE

¡ If you like to repeat the current track in the random selection, press the REPEAT button repeatedly until

“ TRACK” appears during playback. If you like to repeat the entire random selection press the

REPEAT button repeatedly until “ ALL” appears during playback.

– 40 – EN

01A11

PLAYING A MP3 DISC

MP3 PLAYBACK PROGRAM

MP3 MP3

When a CD with MP3 files is in the unit, press the

DISC MENU button to call up the file list.

This feature allows you to program an MP3 disc to play in a desired sequence.

1 In stop mode, press the Arrow button ( K / L ) to select the desired group or track.

¡ If a group is selected, press the Arrow button

B or the

ENTER button to go on to the track selection screen.

Press the Arrow button (

K

/

L

) folder name 1 folder name 2 folder name 3 folder name 4 folder name 5 folder name 6 to choose a track, then press the ENTER button.

¡ If a track is selected, press the ENTER button to start playing tracks. Starting from the one you’ve just chosen the subsequent tracks will be played.

¡ Press the TITLE button to return to the first item.

2 Press the STOP button to stop playback.

NOTES:

¡ Folders are known as Groups; files are known as

Tracks.

¡ MP3 files are accompanied by

3 icon.

¡ Maximum of 255 folders can be recognized.

¡ Maximum of 512 files can be recognized.

¡ Up to 8 hierarchies can be created.

This unit recommends the use of files recorded at the below specifications:

¡ Sampling frequency: 44.1kHz or 48kHz

¡ Constant bit rate: 112kbps ~ 320kbps.

1 In stop mode, press the MODE button.

¡ The PROGRAM screen will appear.

2 Select a desired track using the Arrow button ( K / L / s / B ). Then, press the ENTER button.

¡ Press the Arrow button

B when you want to go to the next hierarchy.

¡ Press the Arrow button s when you want to go back to the previous hierarchy.

¡ Press the CLEAR button to erase the most recently entered program.

3 Repeat step [2] until you have selected all the Tracks you want to play in the program.

4 Press the PLAY button to start programmed playback.

NOTES:

¡ While the program is being played back, the STOP button as follows.

¡ Press the STOP button once and then the PLAY button again, playback will restart from the point where the STOP button was pressed. (Program continued)

¡ Press the STOP button twice and then the PLAY button again, playback will restart from the track in the usual way. (Program cleared)

¡ To erase all tracks in the program at once, select

ALL CLEAR at the bottom of the list at Step [2].

REPEAT

REPEAT is available only during playback.

RANDOM PLAYBACK

MP3

MP3




1 In stop mode, press the MODE button twice.

¡ RANDOM screen appears.

2 Press the PLAY button to start random playback.

TRACK

( current track repeat)

GROUP

( current group repeat)

ALL

( entire disc repeat)

OFF

(repeat off )

NOTE:

¡ Repeat setting will be cleared when moving to other track.

– 41 – EN

01A11

CHANGING THE SETTINGS

SUBTITLE LANGUAGE CAMERA ANGLE

DVD-V

The unit allows you to select a language for subtitles during DVD playback (if available).

1 Press the SUBTITLE button during playback.

2 Press the SUBTITLE button repeatedly to select your desired subtitle language.

¡ The subtitle language will appear on the display bar at the top of the TV screen.

3

To turn off subtitles, press the SUBTITLE button repeatedly until “OFF” appears.

NOTES:

¡ Some discs allow audio language setting/subtitle language setting on the disc menu. (Operation varies between discs, so refer to the manual accompanying the disc.)

¡ If the desired language is not shown after pressing the SUBTITLE button several times, the disc does not have subtitles in that language.

¡ If you choose a Language that has a 3 letter language code, the code will be displayed every time you change the Subtitle language setting. If you choose any other languages, ‘---’ will be displayed instead.

(Refer to page 44.)

Some DVD discs contain scenes which have been shot simultaneously from various angles. You can change the camera angle when the ( ) icon appears on the screen.

1 Press the ANGLE button during playback.

¡ The selected angle will be displayed on the display bar at the top of the screen.

2 Press the ANGLE button repeatedly to select your desired angle.

BLACK LEVEL SETTING

OFF

DVD-V

DVD-V

Adjust the Black Level Settings to make the black parts of the picture brighter.

1 Press the MODE button during playback.

AUDIO LANGUAGE

2 Press the ENTER button to switch OFF.

ON: Makes the dark parts brighter.

OFF: Shows the original picture as recorded.

DVD-V

The unit allows you to select a language during DVD playback (if multi languages are available).

1 Press the AUDIO button during playback.

2 Press the AUDIO button repeatedly to select your desired language.

NOTE:

¡ Pressing the AUDIO button may not work on some

DVDs with multiple audio languages (e.g. DVDs which allow audio language setting on the disc menu).

3

Press the MODE button twice or the

RETURN button to exit.

NOTE:

¡ The setting will be saved even if the unit is turned off.

VIRTUAL SURROUND

DVD-V CD MP3

You can enjoy stereophonic visual space on your existing stereo system.

STEREO SOUND MODE

CD

1 Press the V.SURR button once or the MODE button twice (CD/MP3: once) during playback.

OFF

1 Press the AUDIO button repeatedly during playback to select between STEREO, L-CH or R-CH.

¡ STEREO - both right and left channels are active

L-CH - only left channel is active

R-CH - only right channel is active

NOTE:

¡ If the Virtual Surround setting is ON, the sound mode will be fixed to “STEREO” and can not be changed.

2 Press the ENTER button to set it 1 (Natural effect) or 2 (Emphasized effect) or OFF.

3 Press the V. SURR or RETURN button to exit.

NOTE (for CD play only):

¡ Virtual Surround will not be effective if the sound mode is set to something other than STEREO.

– 42 – EN

01A11

THE ON-SCREEN INFORMATION

DVD-V CD MP3

You can check the information about the current disc by pressing the DISPLAY button on the remote control.

For DVD-Vs

1 Press the DISPLAY button during playback to show current Chapter.

¡ The elapsed and remaining playing time of the current chapter will be displayed.

9/49 0:00:00 -0:03:30

For audio CDs

1 Press the DISPLAY button during playback to show the current Track.

¡ The elapsed and remaining playing time of the current track will be displayed.

2 Press the DISPLAY button again to show current Title.

¡ The elapsed and remaining playing time of the current title will be displayed.

2 Press the DISPLAY button again to show current Total Track.

¡ The elapsed and remaining playing time of the current track will be displayed.

3 Press the DISPLAY button again to exit the display.

3 Press the DISPLAY button again.

¡ The bit rate and the current repeat setting will be displayed.

¡ If you are playing a dual layered disc, the layer number will also be displayed (L0: Layer 0 is playing.

L1: Layer 1 is playing).

For MP3

1 Press the DISPLAY button during playback.

¡ The name of the file currently in play will be displayed.


2 Press the DISPLAY button again to show the track number, the elapsed time, the repeat status, and the playback status at the top of the screen.

¡ will be displayed when repeat play has been selected.

T - indicates Track repeat

G - indicates Group (folder) repeat

A - indicates Disc repeat


– 43 – EN

01A11

CHANGING THE DVD SETUP ITEMS

LANGUAGE SETTING

DVD-V

Language options are not available with some discs.

1 Press the SETUP button twice in STOP mode so that the DVD SETUP menu appears.

¡ If the menu does not appear, press the PLAY button, the STOP button, then the SETUP button twice.

SETUP

QUICK

CUSTOM

INITIALIZE

2 Press the Arrow button L to select CUS-

TOM, then press the ENTER button.

¡ CUSTOM mode will appear.

3 Press the Arrow button ( K / L ) to select

“LANGUAGE”, then press the ENTER button to confirm.

SETUP CUSTOM

LANGUAGE

DISPLAY

AUDIO

PARENTAL

4 Press the Arrow button ( K / L ) to select the next items, then press the ENTER button.

AUDIO: Sets the audio language.

SUBTITLE: Sets the subtitle language.

DISC MENU: Sets the language for DVD menu.

5 Press the Arrow button ( K / L ) to select a setting, then press the ENTER button.

¡ If “OTHER” is selected on the AUDIO, SUBTITLE or DISC MENU screen, press four-digit number to enter the code for the desired language. (Refer to the language code list.)

¡ Only the languages supported by the disc can be selected.

6 Press the SETUP button to exit.

NOTE:

¡ Language Setting for Audio and Subtitle is not available with some discs. Then use the AUDIO and the

SUBTITLE buttons. Details are on page 42.

TO CHANGE THE ON-SCREEN MENUS

You can access the TV/VCR SETUP menu by pressing the SETUP button from the DVD mode. Refer to

“SELECTING THE LANGUAGE” on page 15 to change the menu language.

Language

A-B

Abkhazian

Afar

Afrikaans

Albanian

Amharic

Arabic

Armenian

Assamese

Aymara

Azerbaijani

Bashkir

Basque

Bengali;Bangla

Bhutani

Bihari

Bislama

Breton

Bulgarian

Burmese

Byelorussian

C-E

Cambodian

Catalan

Chinese [CHI]

Corsican

Croatian

Czech

Danish [DAN]

Dutch [DUT]

English [ENG]

Esperanto

Estonian

F-H

Faroese

Fiji

Finnish [FIN]

French [FRE]

Frisian

Galician

Georgian

German [GER]

Greek [GRE]

Greenlandic

Guarani

Gujarati

Hausa

Hebrew

Hindi

Hungarian [HUN]

I-K

Icelandic [ICE]

Indonesian

Interlingua

Interlingue

Inupiak

Irish [IRI]

Italian [ITA]

Japanese [JPN]

Javanese

Kannada

Kashmiri

Kazakh

Kinyarwanda

Kirghiz

Kirundi

Korean [KOR]

Kurdish

4748

4747

4752

6563

4759

4764

5471

4765

4771

4772

4847

5167

4860

5072

4854

4855

4864

4853

5971

4851

5759

4947

7254

4961

5464

4965

5047

6058

5160

5161

5166

5261

5256

5255

5264

5271

5358

5747

5051

5158

5758

5360

5367

5447

5569

5455

5467

5565

5560

5547

5551

5557

5347

5566

5647

5669

5760

5765

5757

6469

5771

6460

5761

5767

Code Language

L-N

Laothian

Latin

Latvian;Lettish

Serbian

Serbo-Croatian

Sesotho

Setswana

Shona

Sindhi

Singhalese

Siswat

Slovak

Slovenian

Somali

Spanish [SPA]

Sundanese

Swahili

Swedish [SWE]

T

Tagalog

Tajik

Tamil

Tatar

Telugu

Thai

Tibetan

Tigrinya

Tonga

Tsonga

Turkish [TUR]

Turkmen

Twi

U-Z

Ukrainian

Urdu

Uzbek

Vietnamese

Volapuk

Welsh

Wolof

Xhosa

Yiddish

Yoruba

Zulu

Lingala

Lithuanian

Macedonian

Malagasy

Malay

Malayalam

Maltese

Maori

Marathi

Moldavian

Mongolian

Nauru

Nepali

Norwegian [NOR]

O-R

Occitan

Oriya

Oromo(Afan)

Panjabi

Pashto;Pushto

Persian

Polish

Portuguese [POR]

Quechua

Rhaeto-Romance

Romanian [RUM]

Russian [RUS]

S

Samoan

Sangho

Sanskrit

Scots Gaelic

If you choose a Language that has a 3 letter language code, the code will be displayed every time you change the Audio or Subtitle language setting on page 42. If you choose any other languages, ‘---’ will be displayed instead. (3 letter language code is written in bracket.)

6757

6764

6772

6855

6861

4971

6961

7054

5655

7161

7267

6658

6653

6647

6666

6651

6654

4861

6655

6661

6665

6664

6657

6669

6559

6553

6547

5350

6564

6554

6566

6660

6560

6550

6555

6565

6557

6558

6561

5165

6567

6569

6568

6149

6164

6159

6247

6265

5247

6258

6266

6367

6459

6461

6467

Code

5861

5847

5868

5860

5866

5957

5953

5965

5958

5966

5955

5964

5961

5960

6047

6051

6061

– 44 – EN

01A11

DISPLAY SETTING AUDIO SETTINGS

DVD-V DVD-V

You can change certain aspects of the DVD display screens and on-screen messages on the TV screen.



SETUP

QUICK

CUSTOM

INITIALIZE

Choose the appropriate Audio settings for your equipment as it only affects during the playback of DVD.



SETUP

QUICK

CUSTOM

INITIALIZE

2 Press the Arrow button L to select “CUS-

TOM”, then press the ENTER button.


3 Press the Arrow button ( K / L ) to select “DIS-

PLAY”, then press the ENTER button to confirm.

SETUP

LANGUAGE

DISPLAY

AUDIO

PARENTAL

CUSTOM





“AUDIO”, then press the ENTER button to confirm.

SETUP CUSTOM

LANGUAGE

DISPLAY

AUDIO

PARENTAL

4 Press the Arrow button ( K / L ) to select the below items, then press the ENTER button.

TV MODE: QUICK

¡ Press the Arrow button ( K / L ) for an item selection,

¡ then press the ENTER button.

Select 4:3 LETTER BOX for black bars to appear on

¡ top and bottom of the screen.

Select 4:3 PAN & SCAN for a full height picture

¡ with both sides trimmed.

The default setting is 4:3 LETTER BOX.

STILL MODE:

¡ Press the Arrow button ( K / L ) for an item selection, then press the ENTER button.

¡ Select “AUTO” usually.

¡ If you select “FIELD”, the picture in the still mode will be stabilized.

¡ If you select “FRAME”, the picture in the still mode will be highly defined.

ANGLE ICON:

¡ Press the ENTER button repeatedly to turn Angle icon ON or OFF.

¡ The default setting is ON.

AUTO POWER OFF:

¡ Press the ENTER button repeatedly to turn Auto

Power off ON or OFF.

¡ The default setting is ON and it will turn the unit off automatically after 15 minutes of no use.

4 Press the Arrow button ( K / L ) to select the below items, then press the ENTER buttons.

DRC (Dynamic Range Control):

¡ To compress the range of soft to loud sound.


DOWN SAMPLING:

¡ Set to ON when outputting in 48 kHz.


When playing disc with copyright Protection

¡ If you select OFF, copyright protection will be activated and sound will be down sampled at 48kHz.

DOLBY DIGITAL: QUICK

Set to On when the unit is connected to a Dolby Digital

Decoder.

ON: Output a Dolby Digital signal

OFF: Convert the Dolby Digital to PCM

(2 channel stereo)


5

Press the SETUP button to exit.

5 Press the SETUP button to exit.

– 45 – EN

01A11

PARENTAL CONTROL

DVD-V

Parental Control limits the disc viewing that exceed your settings. (with a password or playback will stop.)

This feature allows you to prevent discs with alternative scenes from being played by your children.

PARENTAL LEVEL

Parental Level allows you to set the rating level of your DVD discs. Playback will stop if the disc’s ratings exceed the level you set.

1 Press the SETUP button twice in STOP mode so that the QUICK SETUP menu appears.




SETUP

QUICK

CUSTOM

INITIALIZE

CONTROL LEVELS

¡ ALL

All parental lock is cancelled.

¡ Level 8

DVD software of any grade (adult/general/children) can be played back.

¡ Levels 7 to 2

Only DVD software intended for general use and children can be played back.

¡ Level 1

Only DVD software intended for children can be played back, with those intended for adult and general use is prohibited.

IF YOU FORGET THE PASSWORD

1 Press the number buttons 4, 7, 3, 7 at step

[4]. Then enter your new password.

¡ Password will be cleared and parental level will be set to “ALL”.

2 Proceed the steps [5] to [7] again.


“PARENTAL”, then press the ENTER button.

SETUP

LANGUAGE

DISPLAY

AUDIO

PARENTAL

CUSTOM

4 Enter your four-digit password then press the ENTER button.


“PARENTAL LEVEL”, then press the ENTER button.

6 Press the Arrow button ( K / L ) to select the desired level, then press the ENTER button.

7 Press the SETUP button to exit

NOTES:

¡ When doing this for the first time, enter any 4 digits.

(except for 4737) That number will be used as the password.

¡ To change the password, press the Arrow button

( K / L ) to select “CHANGE” at step [5], then press the ENTER button. Enter the four-digit pass-word, then press the ENTER button.

¡ With some DVDs, it may be difficult to find if they are compatible with parental lock. Be sure to check if the parental lock function operates in the way that you have set.

¡ Record the password in case you forget it.

INITIALIZE

This allows you to return all selections of SETUP

(except for PARENTAL) to their default settings.

1 Press the SETUP button twice in STOP mode so that the INITIALIZE menu appears.

2

Press the Arrow button ( K / L ) to select “INI-

TIALIZE”, then press the ENTER button.

3 Select “YES”, then press the ENTER button twice. All the settings (except for

“PARENTAL”) will be cleared.

¡ To cancel the initialization, select “NO”.

4

Press the SETUP button to exit.

EN

01A11

TROUBLESHOOTING GUIDE

If the unit does not perform properly when operated as instructed in this Owner’s Manual, check the unit, consulting the following checklist.

No power

PROBLEM

The unit does not respond to the remote control

CORRECTIVE ACTION

• Make sure the power plug is connected to an AC outlet.

• Make sure the power is turned on.

• Check if the power plug is connected to an AC outlet.

• Check the batteries in the remote control.

• Aim the remote control directly at the remote sensor. If necessary, remove all the obstacles between the sensor and the remote.

• You have to be within 23 feet of the unit.

• Check if the correct mode is selected. If not switch the mode by pressing the SELECT button on the remote control,whichever you need.

TV/VCR Mode

Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked possibilities. Before arranging for service, check these items. It could save your time and money.

PROBLEM

No picture and sound

No picture or poor picture on the screen

No sound or poor sound

Bars On Screen

Picture Distorted or Blurred

Picture Rolls Vertically

Lines or Streaks in Picture

No Color

Poor Reception on Some Channels

Ghosts in Picture

Weak Picture

Sound OK, Picture Poor


• Make sure the AC cord is connected to an AC outlet.

• Check antenna connection.

• Press the SELECT button on the remote control to select TV mode.

Then try other TV feature.

• Let the unit program its tuner memory.

• Adjust direction or replace antenna.

• Adjust picture controls.

• Adjust volume control on remote control or main unit.

• Press the MUTE button to restore sound.

• If outside antenna is being used, check for broken wire.

• Check for local interference.

• Try a new channel, if OK, then possible station trouble.






• Is antenna connected to terminal on the back of the set?


• Adjust COLOR control.








• Adjust CONTRAST & BRIGHT control.





• Adjust CONTRAST & BRIGHT control.

– 47 – EN

01A11

PROBLEM

Picture OK, Sound Poor

Timer recording is not possible

Cannot go into Record mode

Playback picture is partially noisy

No picture but the audio is OK in playback

No operation by infrared Remote

Control

Video or color fades in and out when making a copy of a video tape

Different color marks on screen




• Make sure the timer recording is set correctly.

• Make sure the power is off.

• Make sure the unit’s clock is set correctly.

• Make sure the tape has an erase-prevention tab. If need, cover the

• hole with plastic tape.

•

Adjust tracking control for a better picture using the CHANNEL

• button K or L on the front panel.

•

Head cleaning may be necessary. Refer to “AUTO HEAD

•

CLEANING” on page 50.

•

Make sure the AC cord is connected to an AC outlet.

•

Check batteries in remote control.

•

You can not copy a copyrighted video tape. You are experiencing

• copy guard protection.

• Magnetism from nearby appliances and geomagnetism might affect the color of the TV picture. Move the unit away from the appliances, the unit can repair itself automatically. If you want to repair immediately, unplug the power cord, then plug it in again 30 minutes later or so.

CLOSED CAPTION PROBLEM

The unit is showing misspelled captions.

POSSIBLE REMEDY

• You are watching a live broadcast and spelling errors made by the

• closed captioning production company may pass through uncorrected.

• A prerecorded program will not show any misspelled words because

• of the normal time available for editing the captions.

The unit will not show the text dialogue in its entirety or there is a delay of what is being said.

• Captions that are delayed a few seconds behind the actual are common for live broadcast. Most captioning production

• companies can display a dialogue to a maximum of 220 words

• per minute. If a dialogue exceeds that rate, selective editing is used

• to insure that the captions remain up-to-date with the current

• TV screen dialogue.

The captions are scrambled with • Interference caused by building, power lines, thunderstorms, etc. white boxes on the TV screen.

• may cause scrambled or incomplete captions to appear.

The program guide listed a TV show • Broadcasters may at times use a time compression process to speed as being closed captioned but none • up the actual program so that additional advertising time can be of the captions were displayed.

• given. Since the decoder cannot read the compressed information,

• captions will be lost.

My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating show any captions. The tape box • company accidentally left out the captioning signals during the mentions it being closed captioned.

• copying process.

The TV screen shows a black box • You are in the TEXT mode. Select CAPTION [C1],[C2] or [OFF] on certain channels.

– 48 – EN

01A11

DVD Mode

No picture

PROBLEM

Disc cannot be played

No sound


• Insert a correct video disc that plays on this unit.

• Press the SELECT button on the remote control to select DVD mode.

Then try other DVD feature.

• Insert the disc.

• Clean the disc.

• Place the disc correctly, with the label side up.

• Cancel the parental lock or change the control level.

• Connect the audio cables firmly.

• Turn the power of the audio component on.

• Correct the audio output settings.

• Correct the input settings on the audio component.

No DTS audio is output

Distorted picture

• This unit does not support DTS audio. This is not a malfunction.

• There are some cases where pictures may be slightly distorted, which are not a sign of a malfunction.

Audio or subtitle language does not match the set up

• Although pictures may stop for a moment, this is not a malfunction.

• The selected language is not available for audio or subtitles on the DVD.

This is not a malfunction

The camera angle cannot be changed • The DVD does not contain sequences recorded from different camera angles. This is not a malfunction

Audio or subtitle language cannot be • The DVD does not contain audio source or subtitles in the selected changed language. This is not a malfunction.

“Prohibited icon” appears on the screen, prohibiting an operation

CD sound dropout

No CD reproduction

DVD picture dropout

DVD picture freeze

DVD picture in mosaic

No DVD reproduction

• That operation is prohibited by the player or the disc.

This is not a malfunction.

• Scratched disc. Replace the disc with unscratched one.

NOTES:

• Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Owner’s Manual for details on correct operations.

• Playback from a desired track and random playback are not available during program playback.

– 49 – EN

01A11

MAINTENANCE

CABINET CLEANING

• Wipe the front panel and other exterior surfaces of the unit with a soft cloth immersed in lukewarm water and wrung dry.

• Never use a solvent or alcohol. Do not spray insecticide liquid near the unit. Such chemicals may cause damage and discoloration to the exposed surfaces.

1. Please visit your local Audio/Video store and purchase a good quality VHS Video Head Cleaner.

2. If a Video Head Cleaner does not solve the problem, please call our help line at 1-800-968-3429, to locate an Authorized Service Center.

NOTES:

• Remember to read the instructions included with the video head cleaner before use.

• Clean video heads only when problems occur.

AUTO HEAD CLEANING

• Automatically cleans video heads as you insert or remove a cassette, so you can see a clear picture.

• Playback picture may become blurred of interrupted while the TV program reception is clear. Dirt accumulated on the video heads after long periods of use, or the usage of rental or worn tapes can cause this problem.

If a streaky or snowy picture appears during playback, the video heads in your unit may need to be cleaned.

SERVICING

• Should your unit become inoperative, do not try to correct the problem by yourself. There are no userserviceable parts inside. Turn off, unplug the power cord, and please call our help line at 1-800-968-

3429, to locate an Authorized Service Center.

IF THE LASER OPTICAL PICKUP UNIT IS DIRTY

• If the unit still does not perform properly when it is operated while referring to the relevant sections and to

“TROUBLESHOOTING GUIDE” in this Owner's Manual, the laser optical pickup unit may be dirty. Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.

Recordable

DISC HANDLING

• Use discs which have the following logos on them.

(Optical audio digital discs.) •

• To clean-off, use a soft cloth.

Do not use a hard cloth since this will mar the disc.

• Wipe the disc in a straight line from center to edge.

• Never wipe with a circular motion.

• Do not use detergent or abrasive cleaning agents.

• Handle the discs so that fingerprints and dust do not adhere to the surfaces of the discs.

• Always store the disc in its protective case when it is not used.

– 50 –

SPECIFICATIONS

GENERAL SPECIFICATIONS

TV/VCR

CRT 19 inch in-line gun,

90˚ deflection tube

Television system : NTSC-M

Closed caption system :§15.119/FCC

Video Heads : Rotary four-head

Tape width :

Tape speed

1/2 inch

SP :

LP :

SLP :

Tuner channel

33.40mm/sec.

16.67mm/sec.

11.12mm/sec.

TV VHF Low : #2~#6

TV VHF High : #7~#13

TV UHF :

CATV

#14~#69

VHF :

MID band :

SUPER band :

HYPER band :

5A

A5~A1, A~I

J~W

W+1~W+84

ELECTRICAL SPECIFICATIONS

Sound output: 2 speakers, 1W, 8 ohm

OTHER SPECIFICATIONS

Terminals

Antenna input:

Headphone:

Coaxial digital

VHF/UHF/CATV

75 ohm unbalanced (F-type)

Video input: RCA connector [ 1

Audio L/R input: RCA connector [ 2

1/8" stereo (3.5 mm) audio output:

Remote control:

One pin jack,

500m Vpp (75 ohm)

Digital encoded infrared light system

Operating temperature: 5°C to 40°C

(41°F~104°F)

Power requirements: AC 120V, 60Hz

Power consumption

(Maximum):

Picture tube:

Dimensions:

90W

19"

H:19-11/16" (500mm)

Weight:

W:21-7/8" (556mm)

D:18-3/4" (477mm)

45.2 lbs (20.5kg)

DVD

Product type: DVD Player

Discs: DVD video, Audio CD

Output signal format: NTSC color

• Designs and specifications are subject to change without notice.

• If there is a discrepancy between languages, the default language will be English.

– 51 – EN

01A11

INDICE

■

CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 52

PANEL FRONTAL DEL TELEVISOR/DVD. . . . . . . . . . 52

MANDO A DISTANCIA . . . . . . . . . . . . . . . . . . . . . . . . . 52

VISTA POSTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

■

PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 53

CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 53

CONEXIÓN A TOMAS DE ENTRADA EXTERNA. . . . 53

PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 54

MODO DE ENTRADA EXTERNA . . . . . . . . . . . . . . . . 54

CONEXIÓN A UN SISTEMA ESTÉREO . . . . . . . . . . . . 54

CONEXIÓN A UN AMPLIFICADOR ESTÉREO

EQUIPADO CON TOMAS DE ENTRADA DIGITAL

(Para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

CONEXIÓN A UN DECODIFICADOR DOLBY DIGITAL

(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

SECCIÓN DE TV/VCR

■

PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 54

SELECCI ÓN DE IDIOMA . . . . . . . . . . . . . . . . . . . . . . . 54

AJUSTE DE CANALES . . . . . . . . . . . . . . . . . . . . . . . . . 55

AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

SECCIÓN DE DVD

REPRODUCCIÓN BÁSICA . . . . . . . . . . . . . . . . . . . . . . 55

CONTROLES DE

OPERACIÓN Y FUNCIONES

PANEL FRONTAL

Consulte la figura 1 de la página 9

MANDO A DISTANCIA


VISTA POSTERIOR


1.

Botón POWER

Presione para conectar y desconectar la alimentación.

2.

Botones VOLUME X / Y

Presione para controlar el nivel de volumen del DVD y el televisor.

3.

Botones SKIP (para DVD)

Presione el botón correspondiente una vez para omitir capítulos o pistas y desplazarse a un punto específico.

Mantenga el botón presionado para cambiar la velocidad de reproducción en avance o retroceso.

4.

Botón PLAY

Inicia la reproducción del contenido del disco o cinta.

5.

Botón STOP

Detiene la reproducción del disco o cinta.

6.

Botón OPEN/CLOSE

Presione para insertar discos en la bandeja o retirarlos de ella.

7.

Bandeja de carga del disco

8.

Indicador DVD

Se ilumina durante el modo DVD.

9.

Botón SELECT

Presione para cambiar al modo TV/VCR, modo de entrada externa o modo de DVD.

10.

Indicador TV/VCR

Se ilumina durante el modo TV/VCR.

11.

Botones CHANNEL K / L

Presione para seleccionar canales memorizados.

– 52 –

12.

Indicador de grabación

Parpadea durante la grabación. Se ilumina durante el modo de espera de grabación controlada por temporizador.

13.

Botón REC/OTR (Panel frontal)

Presione para empezar la grabación manual. Presione repetidamente para empezar la grabación instantánea

(OTR).

Botón RECORD (Mando a distancia)

Presione para empezar la grabación manual.

14.

Botón REW (para TV/VCR)

Presione para rebobinar la cinta o para ver la imagen rápidamente en dirección de retroceso durante el modo de reproducción. (Búsqueda en dirección de retroceso)

15.

Botón F.FWD (para TV/VCR)

Presione para adelantar rápidamente la cinta o para ver la imagen rápidamente en dirección de avance durante el modo de reproducción. (Búsqueda en dirección de avance)

16.

Botón STOP/EJECT

Presione para detener la cinta. Presiónelo en el modo de parada para retirar la cinta de la unidad.

17.

Ventanilla del sensor de mando a distancia

18.

Toma HEADPHONE

Para conectar auriculares (no suministrados) y escuchar en privado.

19.

Toma de entrada VIDEO

Conecte aquí la toma de salida de vídeo de una videocámara o de una videograbadora.

20.

Tomas de entrada AUDIO L/R

Conecte aquí las tomas de salida de audio de una videocámara o de una videograbadora.

21.

Compartimiento del cassette

22.

Botón PICTURE

Presione para ajustar la imagen.

23.

Botones numéricos

Modo TV/VCR:

Presione dos botones para acceder directamente al canal deseado.

No olvide presionar “0” antes de elegir un canal de un solo dígito.

Botón +100

Presione este botón para seleccionar canales de televisión por cable cuyo número sea igual o superior a 100.

Modo DVD:

Presione este botón para introducir el número deseado.

Botón +10

Presione este botón para introducir números iguales o mayores que 10.

24.

Botón PAUSE

Hace una pausa en la reproducción del disco o cinta.

25.

Botón SPEED

Presione para seleccionar la velocidad de grabación deseada: SP/SLP.

26.

Botón C.RESET

Presione para poner el contador en 0:00:00.

Presiónelo también para cancelar un ajuste de programa de temporizador.

27.

Botón DISPLAY

Modo TV/VCR:

Para visualizar el contador o el número del canal y la fecha actual en la pantalla del televisor.

Modo DVD:

Para visualizar el estado actual en la pantalla del televisor.

28.

Botón SETUP

Presione para activar o salir del modo de menús de televisor o configuración de DVD.

29.

Botón TITLE

Para visualizar el menú de títulos.

ES

0C28

30.

Botón CLEAR

Para cancelar ajustes.

31.

Botón MODE

Activa el modo de reproducción programada o el modo de reproducción aleatoria.

32.

Botón SEARCH MODE

Presione para localizar un punto deseado.

33.

Botón AUDIO

Presione para seleccionar un idioma de audio o el modo de sonido deseado.

34.

Botón SUBTITLE

Presione para seleccionar el idioma de subtítulos deseado.

35.

Botón REPEAT

Repite la reproducción del disco, título, capítulo o pista actual.

36.

Botón ANGLE (modo DVD)

Presione para cambiar el ángulo de la cámara y ver la secuencia que se está reproduciendo desde un ángulo diferente.

37.

Botón A-B REPEAT

Repite la reproducción de una sección seleccionada.

38.

Botón RETURN

Permite volver a la operación anterior en el modo de configuración de DVD.

39.

Botón ENTER

Presione para establecer un ajuste.

40.

Botones de flechas

Modo TV/VCR:

Presione para seleccionar un modo de ajuste en el menú que aparece en la pantalla del televisor.

Presiónelos también para seleccionar opciones o establecer ajustes en un menú en particular.

Modo DVD:

Presione para hacer ajustes mientras observa la imagen en la pantalla del televisor.

41.

Botón DISC MENU

Muestra los menús contenidos en el DVD.

42.

Botón V.SURR

Activar/desactivar el envolvente virtal.

43.

Botón MUTE

Suprime la salida de sonido. Presiónelo de nuevo para restablecer el sonido.

44.

Botón SLEEP

Presione para ajustar el temporizador de dormir.

45.

Botón SELECT

Presione para cambiar entre los modos TV/VCR y

DVD. El modo seleccionado (TV/VCR o DVD) se visualiza en el indicador del panel delantero.

46.

Toma de entrada ANT.

Conéctela a una antena, sistema de televisión por cable o sistema de satélite.

47.

Cable de alimentación

Conéctelo a una toma de CA estándar (120 V, /60 Hz).

NOTA: Antes de conectar el cable de alimentación a una toma de CA estándar, retírelo del gancho para evitar dañarlo.

48.

Toma de salida de audio digital COAXIAL

Conéctela solamente a la entrada digital de un amplificador externo o decodificador (de audio de DVD).

PREPARACIÓN PARA LA

UTILIZACIÓN

CONEXIONES DE ANTENA/CABLE


ANTENAS SEPARADAS DE VHF/UHF

En algunas zonas será necesario utilizar una antena exterior.

TELEVISIÓN POR CABLE SIN CAJA DE

CONVERTIDOR/DECODIFICADOR

Utilice esta conexión si su sistema de televisión por cable se conecta directamente a la unidad, sin una caja de convertidor.

Con esta conexión podrá:

1) Utilizar el mando a distancia de la undad para seleccionar canales.

2) Programar uno o más canales decodificados para grabación automática controlada por temporizador.

NOTA: Este unidad SÓLO puede grabar el canal que se está viendo.

TELEVISIÓN POR CABLE CON CAJA

DE CONVERTIDOR/DECODIFICADOR

O CAJA DE SATÉLITE

Si su compañía de televisión por cable le suministra una caja de convertidor o si utiliza un sistema de satélite, podrá utilizar la conexión básica que se muestra en la ilustración.

Al utilizar esta conexión, también podrá grabar canales codificados. Sin embargo, la selección de los canales deberá hacerse con la caja de convertidor o con la caja de satélite. Esto significa que no es posible cambiar de canal utilizando el mando a distancia de la unidad. La grabación en ausencia (controlada por temporizador) está limitada a un canal a la vez.

PARA GRABAR UN CANAL

CODIFICADO/DECODIFICADO

1. Ajuste el selector de canales del unidad al canal de salida de la caja de convertidor de televisión por cable o caja de satélite. (Ej., CH3)

2. Seleccione el canal que desea grabar en la caja de convertidor de televisión por cable o caja de satélite.

Nota para el instalador de sistemas CATV

Esta nota tiene la finalidad de llamar la atención del instalador de sistemas CATV para que tenga en cuenta el Artículo 820-40 de la NEC, que proporciona recomendaciones para hacer una conexión a tierra apropiada y, en particular, especifica que la tierra del cable debe conectarse al sistema de puesta a tierra del edificio, tan cerca del punto de entrada del cable como sea posible.

CONEXIÓN A TOMAS DE ENTRADA

EXTERNA

Cuando vea un programa grabado en otra fuente (videograbadora o videocámara), utilice las tomas de entrada de audio/vídeo de la parte delantera de la unidad.

Conecte las tomas de salida de audio/vídeo de otra fuente a las tomas AUDIO L/R y VIDEO de este televisor/ videograbadora/DVD. Luego, presione los botones CHAN-

NEL K / L hasta que aparezca “AUX” en la pantalla.

NOTA:

• Cuando conecte una videograbadora monofónica (otra fuente) a esta unidad, conecte la toma de salida de audio de la videograbadora monofónica (otra fuente) a la toma

AUDIO L de esta unidad. El audio saldrá igualmente por los canales izquierdo y derecho.


– 53 – ES

0C28

PARA INSERTAR LAS PILAS

1) Abra la cubierta del compartimiento de las pilas empujando la cubierta del mando a distancia en el sentido de la flecha.

2) Inserte 2 pilas “AA” en el compartimiento de las pilas, en el sentido indicado por las marcas de polaridad (+/-).

3) Vuelva a poner la cubierta.

MODO DE ENTRADA EXTERNA

Al usar una señal de entrada externa (otra videograbadora o una videocámara), conecte los cables de salida de audio/vídeo del equipo externo a las tomas AUDIO L/R

IN/ VIDEO IN de su televisor/videograbadora/DVD.

Luego, presione los botón CHANNEL K o L hasta que aparezca "AUX" en la pantalla.


NOTAS:

• Asegúrese de desconectar la alimentación de todos los componentes del sistema antes de conectar otro componente.

• Consulte los manuales de instrucciones de los componentes que va a conectar a la unidad.

• Si conecta un decodificador Dolby Digital, ajuste la función DOLBY DIGITAL a ON para salida de audio en el modo de configuración.

• A menos que se haga la conexión a un decodificador Dolby Digital, ajuste la función Dolby

Digital a OFF para salida de audio en el modo de configuración. La reproducción en una unidad utilizando ajustes incorrectos puede generar ruido y distorsión, y también puede causar daños a los altavoces.

Fabricado bajo licencia de Dolby

Laboratories. “Dolby” y el símbolo de la D doble son marcas de fábrica de Dolby

Laboratories.

CONEXIÓN A UN AMPLIFICADOR

ESTÉREO EQUIPADO CON TOMAS DE

ENTRADA DIGITAL (Para DVD)

Utilice un cable digital coaxial de audio de venta en el comercio especializado para hacer las conexiones de audio.

Conexión a un amplificador equipado con tomas de entrada digital, platina MD o platina DAT.


SECCIÓN DE TV/VCR

PREPARACIÓN PARA LA

UTILIZACIÓN

NOTAS:

•

La fuente de audio de un disco grabado en formato de sonido envolvente Dolby Digital de 5,1 canales no se puede grabar como sonido digital mediante una platina MD o DAT.

•

Asegúrese de desconectar la alimentación de todos los componentes del sistema antes de conectar otro componente.

•

Consulte los manuales de instrucciones de los componentes que va a conectar al televisor/videograbadora/DVD.

•

Ajuste la función Dolby Digital a OFF para salida de audio en el modo de configuración. La reproducción en una unidad utilizando ajustes incorrectos puede generar ruido y distorsión, y también puede causar daños a los altavoces.

SELECCIÓN DE IDIOMA

TV/VCR

1

Enchufe el cordón de alimentación de la unidad

Enchufe el cordón de alimentación de la unidad en una toma de CA estándar.

NOTA:

• Si aparecen algunas cifras en la esquina de la pantalla, pulse el botón POWER sin desenchufar el cordón de alimentación.

Asegúrese de que ...

• Pulse el botón POWER para encender el televisor/videograbadora/DVD.

NOTA: Esta función afecta sólo el idioma en el menú de la pantalla y no la fuente de audio.

CONEXIÓN A UN DECODIFICADOR

DOLBY DIGITAL (para DVD)

Si utiliza esta unidad para reproducir un disco DVD grabado en formato de sonido envolvente Dolby

Digital de 5,1 canales, el televisor/videograbadora/DVD emitirá un flujo de datos DOLBY DIGITAL desde su toma de salida de audio digital COAXIAL. Si conecta el reproductor a un decodificador Dolby Digital, podrá disfrutar de una tonalidad más convincente y real, con un sonido envolvente potente y de alta calidad similar al de los cines.

Utilice cables digitales coaxiales de audio disponibles en el comercio especializado para hacer las conexiones de audio.

– 54 –

2

Seleccione “LANGUAGE”

Pulse el botón SETUP en el mando a distancia.

Pulse el botón K o L para señalar “LANGUAGE”.

3

Seleccione “ENGLISH”, “ESPAÑOL” o

“FRANÇAIS”

Seleccione “ENGLISH”, “ESPAÑOL” o “FRANÇAIS” con el botón ENTER.

4

Salga del modo de idioma

Pulse el botón SETUP en el mando a distancia para volver al modo del televisor.

ES

0C28

NOTA: Si, por alguna razón, el menú está en francés, pulse el botón SETUP en el mando a distancia, pulse el botón K o L para señalar el “LANGAGE [FRANÇAIS]”, a continuación, pulse el botón ENTER y pulse el botón

SETUP en el mando a distancia.

AJUSTE DE CANAL

TV/VCR

Puede programar el sintonizador para buscar todos los canales que recibe en su localidad.

NOTA: El canal preparado NO es necesario cuando esté conectado a una caja de cable o caja de satélite.

Sólo tiene que seleccionar con el selector de canal de la unidad al canal de salida de la caja de cabe o caja de satélite (por ejemplo el canal CH3). Seleccione el canal a ver en la caja de cable o caja de satélite.

AJUSTE DEL RELOJ

TV/VCR

Cerciórese...

• La alimentación de la unidad deberá estar conectada.

En el ejemplo de abajo, el reloj va a ajustarse así:

FECHA: 5 de mayo de 2005

HORA: 5:40 PM

1) Pulse el botón SETUP en el mando a distancia.

Pulse el botón K o L para indicar “AJUSTE

RELOJ”.

Luego, pulse el botón ENTER.

2) Pulse el botón K o L para indicar “AJUSTE

MANUAL RELOJ”.

Luego, pulse el botón ENTER.

3) Pulse el botón K o L hasta que aparezca el mes deseado. (Ejemplo: Mayo - 05)

Luego, pulse el botón B .

4) Pulse el botón K o L hasta que aparezca el día del mes deseado. (Ejemplo: 5 - 05)


5) Pulse el botón K o L hasta que aparezca el año deseado. (Ejemplo: 2005)


6) Pulse el botón K o L hasta que aparezca la hora deseada. (Ejemplo: 5, PM)


7) Pulse el botón K o L hasta que aparezca el minuto deseado. (Ejemplo: 40)

8) Pulse el botón SETUP en el mando a distancia.

Aunque los segundos no se visualizan, éstos empiezan a contar desde 00 cuando se pulsa

SETUP en el mando a distancia. Utilice esta función para sincronizar el reloj con la hora correcta.

Asegúrese de que ...

• Pulse el botón POWER para encender el unidad.

1

Seleccione “AJUSTE DE CANAL”

Pulse el botón SETUP en el mando a distancia.

Pulse el botón K o L para señalar “AJUSTE DE

CANAL”.

A continuación, pulse el botón ENTER.

2

Empiece el prefijado automático

Pulse el botón K o L para señalar “AUTOPROGRA-

MACION DE CA”.

A continuación, pulse el botón ENTER.

El sintonizador busca y memoriza todos los canales activos en su localidad.

3

Después de buscar

El sintonizador se detiene en el canal memorizado más bajo.

• Cuando se activa AUTOPROGRAMACION DE

CA, donde no hay entrada de señal del televisor, aparecerá “NO HAY SEÑAL DE TV” en la pantalla después de terminar la búsqueda de canales.

• El unidad puede reconocer los canales de TV para que sean canales de TV de antena de cable con las condiciones de recepción. En este caso, pruebe nuevamente con el prefijado automático en las condiciones de recepción fina.

SECCIÓN DE DVD

REPRODUCCIÓN BÁSICA

DVD-V CD MP3

Para empezar

¡ Conecte la alimentación del amplificador y otros componentes, si es necesario.

1 Presione el botón POWER.

¡ La alimentación se conectará.

2 Presione el botón OPEN/CLOSE para abrir la bandeja de carga del disco.

3 Ponga el disco deseado en la bandeja, con la etiqueta hacia arriba.

4 Presione el botón PLAY.

¡ La bandeja se cerrará automáticamente y la reproducción comenzará desde el primer capítulo o pista del disco. Si la reproducción no comienza automáticamente, presione el botón PLAY.

¡ Cuando reproduzca un DVD que tenga grabado un menú de títulos, el menú podrá aparecer en la pantalla.

5 Presione el botón STOP para detener la reproducción.

– 55 – ES

0C28

LIMITED WARRANTY

FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or workmanship as follows:

DURATION:

PARTS: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this warranty.

LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original retail purchase.

LIMITS AND EXCLUSIONS:

THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE

RECEIPT OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH

THE PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY.

This warranty shall not be extended to any other person or transferee.

This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to any product not purchased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this product or damage which results from fire, flood, lightning or other acts of God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE

CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY

GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE

USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF

FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS

REPRESENTATIVES IN THE UNITED STATES.

ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED

SERVICE CENTER. THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO A FUNAI

AUTHORIZED SERVICE FACILITY.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS

THAT VARY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE

UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI

CORP.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT

WITHOUT PRIOR NOTICE.

To locate your nearest SYLVANIA Authorized Service Center or for general service procedure, please call 1-800-968-3429 or write to the following:

FUNAI CORPORATION, INC.

SERVICE CENTER

19900 Van Ness Avenue, Torrance, CA 90501

Tel :1-800-968-3429 http://www.funai-corp.com

Head Office: 100 North Street, Teterboro, NJ 07608

PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.

Printed in Malaysia 1EMN20246

T0051UB

★★★★★

No results