advertisement
Wireless
Bluetooth Headset
User Manual
Table of Contents
1 Introduction 1
Package Contents 1
Features 2
Putting On the Headset
2 Using the Wireless Headset
Charging the Battery
Turning the Headset On/Off
Pairing the Headset
Handling Calls
Connecting to a Computer
Connecting to Other Devices 9
3 Troubleshooting 11
Notices 13
Regulatory Compliance Notices 13
Modifications 13
Limited Warranty 15
7
8
5
6
2
5
5 i
Action tec Wireless Bluetooth Headset User Manual ii
Introduction
1
Thank you for purchasing the Action tec Wireless Bluetooth Headset. The Headset allows the user to communicate between various Bluetooth devices, including cellular phones, personal digital assistants, and laptop computers, using advanced voice-recognition technology.
Important! Please read this entire chapter. It contains important safety information.
Package Contents
Action tec Wireless Bluetooth Headset
Power Adapter
Installation mini-CD (include User Manual)
Earpads
Quick Start Guide
Accessory bag
1
Action tec Wireless Bluetooth Headset User Manual
Features
The Headset features two buttons (Large and Small), which have various functions, as well as two lights (LEDs), red and blue.
Putting On the Headset
You can wear the Wireless Bluetooth Headset on either ear. The ear brace is detachable from the earpiece section of the Headset. Simply remove it from the
Headset and set it in the appropriate direction to fit your ear.
2
Chapter 1 Introduction
Technical Support
Action tec Electronics prides itself on making durable, high-quality, high-performance products. If you need assistance, the Action tec Technical Support Department is available 24 hours a day, seven days a week, to provide professional support.
Action tec Electronics, Inc.
760 N. Mary Avenue
Sunnyvale, CA 94085
Technical Support
Phone: 1-888-436-0657
E-mail: http://support.actiontec.com/email_support/support_form.php
Internet: www.actiontec.com/support
3
Action tec Wireless Bluetooth Headset User Manual
4
Using the Wireless
Headset
2
This chapter contains instructions on how to use the Headset, including charging the Battery and connecting to a Bluetooth-enabled cellular phone.
Charging the Battery
The rechargeable battery included with the Headset is not fully charged when new, and must be recharged before using. Recharging the first time takes approximately
4 hours; afterwards, each full battery recharge will take approximately 2 hours. A fully charged battery will provide approximately 3 to 4.5 hours of talk time, and
100+ hours of standby time. To recharge the battery:
1.
Plug the battery charger into a wall outlet. The green light on the charger will illuminate.
2.
Connect the other end of the battery charger into power port on the bottom of the Headset. A click is heard when the charger is properly inserted in the power port, and the red light on the charger will illuminate.
3.
When the battery is full, the red light will turn off.
Turning the Headset On/Off
Turning On
To turn the Headset on, press and hold the Large Button for three seconds. Two short, high-pitched tones will sound, then the blue light on the Headset will illuminate. The Headset is now turned on.
☞
Note : If the Headset’s rechargeable batter is low, the red light on the Headset will flash.
5
Action tec Wireless Bluetooth Headset User Manual
Turning Off
To turn the Headset off, press and hold the Large Button for three seconds. Two short, low-pitched tones will sound, then the red light will flash. When it stops flashing, the Headset is turned off.
Pairing the Headset
To use the Headset with a cellular phone, it must be paired with the phone. To do this:
1.
Press the Large Button for 5 seconds. Two high-pitched tones will sound, followed by two more tones, and then the red and blue lights will flash.
2.
Initiate the pairing procedure on the Bluetooth-enable cellular phone to pair with the Headset. Make sure the cellular phone is in discovery mode.
3.
Place the Headset one to three feet from the cellular phone.
4.
When the cellular phone requests a passkey, enter 1234 (the default PIN of the Headset). When pairing is successful, the red light will turn off, and the blue light will illuminate.
If the pairing fails, the Headset will turn off automatically after two minutes.
About Pairing
Pairing is the process of associating Bluetooth devices with each other. When two devices are paired, they establish a permanent, secure link with each other, enabling quick access to services provided without having to enter passwords every time either device is activated.
Paired devices remain paired even when one of the devices is not powered up, the service connection is stopped or interrupted, or one or both of the devices are rebooted.
6
Chapter 2 Using the Headset
Handling Calls
Once the Headset is successfully paired with a cellular phone, you can use it to make and receive calls. If your cellular phone suppors voice dialing, you can perform this with the Headset.
Making Calls
There are two ways to make a call, using the Headset: keying in the number on the cellular phone dial pad, or using voice dialing (if the cellular phone supports this feature).
Using the Dial Pad
To use the dial pad on the cellular phone, dial the phone number. Once the call is placed, the conversation will be carried by the Headset.
Using Voice Dialing
To use voice dialing, press the Large Buttone until a beep is heard. Say the name of the person to be called. The call is placed.
Answering/Ending Calls
When an incoming call is received, a beep is heard, and the blue light will flash quickly. To answer:
1.
Press the Large Button.
2.
If needed, adjust the volume. Press the Large Button to increase the volume; press the Small Button to decrease the volume.
3.
To end the call, press the Small Button for three seconds, or do nothing. After
10 seconds, the Headset will automatically disconnect.
If the Headset if powered off and an incoming call is received, press the Large
Button for three seconds to answer the call.
☞
Note : Due to the design of some cellular phones, the Headset may auto-disconnect even if it is powered on, and will not beep when receiving an incoming call. To reconnect the Headset to the cellular phone, press the Large Button for one second.
7
Action tec Wireless Bluetooth Headset User Manual
Connecting to a Computer
To connect the Headset to a computer, the computer must be Bluetooth-enabled
(i.e., support Bluetooth internally or have a Bluetooth adapter installed). The computer must support Audio Gateway Profiles.
1.
Press the Large Button for 5 seconds. Two high-pitched tones will sound, followed by two more tones, and then the red and blue lights will flash.
2.
On the computer, open the Bluetooth Configuration screen and doubleclick Find Bluetooth Devices .
☞
Note : The Bluetooth Configuration setup may differ based on the brand of the Bluetooth adapter you are using.
3.
Place the Headset firmly in either ear.
4.
On the computer, Right-click on the CSR-bc2 icon. From the menu that appears, select Pair Device .
8
Chapter 2 Using the Headset
5.
A new window appears, requesting a passkey to connect to the Headset. Enter
1234 , then press E nter .
6.
The Headset icon turns green. The Headset is successfully connected to the computer.
Connecting to Other Devices
To connect the Headset to another type of device (a PDA, for example), the device must support Audio Gateway Profiles. Refer to the user manual of the other device to set up the Headset.
9
Action tec Wireless Bluetooth Headset User Manual
10
Troubleshooting
This section details problems that may occur when using the Headset, and solutions for them.
3
The Red Light is flashing. What does this mean?
When only the Red light is flashing, the Headset’s rechargeable battery is running low. Plug the Headset into a wall outlet via the power adapter and recharge the battery. Full recharge takes approximately two hours.
I charged the Headset’s battery for 20 minutes, but it still doesn’t work.
What can I do?
The Headset’s rechargeable battery must be charged for at least 40 minutes before it can be used. It is recommended, however, that the battery be charged for the full two hours.
I plugged the Headset into an electrical socket, but it doesn’t appear to be recharging. What’s going on?
If the Headset hasn’t been used for a long time, or the battery is nearly empty, it may take a few minutes for the Red Light to flash and indicate that it is recharging.
I am getting no sound between the Headset and the device it’s connnected to. What should I do?
Check the following:
• Make sure the Headset and the device have been paired.
• Make sure the Headset is turned on.
• Make sure the Headset and the device are withn working range of each other.
• If connecting to a cellular phone, make sure it has good signal strength.
• Some cellular phones support only one Bluetooth headset at a time.
Disconnection can occur if more than one Headset is being used.
11
Action tec Wireless Bluetooth Headset User Manual
12
Notices
Regulatory Compliance Notices
Class B Equipment
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by implementing one or more of the following measures:
Reorient or relocate the receiving antenna;
Increase the separation between the equipment and receiver;
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected;
Consult the dealer or an experienced radio or television technician for help.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by A ction tec Electronics, Inc., may void the user’s authority to operate the equipment.
Declaration of conformity for products marked with the FCC logo – United States only.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1 .
This device may not cause harmful interference;
13
Action tec Wireless Bluetooth Headset User Manual
2.
This device must accept any interference received, including interference that may cause unwanted operation.
☞
Note : To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
For questions regarding your product or the FCC declaration, contact:
Action tec Electronics, Inc.
760 North Mary Ave.
Sunnyvale, CA 94086
United States
Tel: (408) 752-7700
Fax: (408) 541-9005
14
Limited Warranty
Hardware : Action tec Electronics, Inc., warrants to the end user (“Customer”) that this hardware product will be free from defects in workmanship and materials, under normal use and service, for twelve (12) months from the date of purchase from Action tec Electronics or its authorized reseller.
Action tec Electronics’ sole obligation under this express warranty shall be, at
Action tec’s option and expense, to repair the defective product or part, deliver to
Customer an equivalent product or part to replace the defective item, or if neither of the two foregoing options is reasonably available, Action tec Electronics may, in its sole discretion, refund to Customer the purchase price paid for the defective product. All products that are replaced will become the property of Action tec Electronics,
Inc. Replacement products may be new or reconditioned.
Action tec Electronics warrants any replaced or repaired product or part for ninety (90) days from shipment, or the remainder of the initial warranty period, whichever is longer.
Software : Action tec Electronics warrants to Customer that each software program licensed from it will perform in substantial conformance to its program specifications, for a period of ninety (90) days from the date of purchase from Action tec
Electronics or its authorized reseller.
Action tec Electronics warrants the media containing software against failure during the warranty period. The only updates that will be provided are at the sole discretion of Action tec Electronics and will only be available for download at the Action tec Web site, www.actiontec.com.
Action tec
Electronics’ sole obligation under this express warranty shall be, at Action tec
Electronics’ option and expense, to refund the purchase price paid by Customer for any defective software product, or to replace any defective media with software which substantially conforms to applicable Action tec Electronics published specifications. Customer assumes responsibility for the selection of the appropriate applications program and associated reference materials.
Action tec Electronics makes no warranty or representation that its software products will meet Customer’s requirements or work in combination with any hardware or applications software products provided by third parties, that the operation of the software products will be uninterrupted or error free, or that all defects in the software products will be corrected. For any third-party products listed in the Action tec Electronics software product documentation or specifications as being compatible, Action tec
Electronics will make reasonable efforts to provide compatibility, except where the non-compatibility is caused by a “bug” or defect in the third party’s product or from use of the software product not in accordance with Action tec Electronics published specifications or user guide.
15
Action tec Wireless Bluetooth Headset User Manual
THIS ACTION TEC ELECTRONICS PRODUCT MAY INCLUDE OR BE BUNDLED
WITH THIRD-PARTY SOFTWARE, THE USE OF WHICH IS GOVERNED BY A SEPA-
RATE END-USER LICENSE AGREEMENT.
THIS ACTION TEC ELECTRONICS WARRANTY DOES NOT APPLY TO SUCH THIRD-
PARTY SOFTWARE. FOR THE APPLICABLE WARRANTY, PLEASE REFER TO THE
END-USER LICENSE AGREEMENT GOVERNING THE USE OF SUCH SOFTWARE.
Obtaining Warranty Service : Customer may contact Action tec Electronics
Technical Support Center within the applicable warranty period to obtain warranty service authorization. Dated proof of purchase from Action tec Electronics or its authorized reseller may be required. Products returned to Action tec Electronics must be pre-authorized by Action tec Electronics with a Return Merchandise
Authorization (RMA) number marked on the outside of the package, and sent prepaid and packaged appropriately for safe shipment, and it is recommended that they be insured or sent by a method that provides for tracking of the package. The repaired or replaced item will be shipped to Customer, at Action tec Electronics’ expense, not later than thirty (30) days after Action tec Electronics receives the defective product.
Return the product to:
(In the United States)
Action tec Electronics, Inc.
760 North Mary Avenue
Sunnyvale, CA 94085
Action tec Electronics shall not be responsible for any software, firmware, information, memory data, or Customer data contained in, stored on, or integrated with any products returned to Action tec Electronics for repair, whether under warranty or not.
WARRANTIES EXCLUSIVE : IF AN ACTION TEC ELECTRONICS’ PRODUCT DOES
NOT OPERATE AS WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY FOR
BREACH OF THAT WARRANTY SHALL BE REPAIR, REPLACEMENT, OR REFUND OF
THE PURCHASE PRICE PAID, AT ACTION TEC ELECTRONICS’ OPTION. TO THE
FULL EXTENT ALLOWED BY LAW, THE FOREGOING WARRANTIES AND REME-
DIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, TERMS OR
CONDITIONS, EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF
LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES, TERMS OR CONDI-
TIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, SATISFAC-
TORY QUALITY, CORRESPONDENCE WITH DESCRIPTION, AND NON-INFRINGE-
MENT, ALL OF WHICH ARE EXPRESSLY DISCLAIMED.
ACTION TEC ELECTRONICS
16
Limited Warranty
NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT
ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAIN-
TENANCE OR USE OF ITS PRODUCTS.
ACTION TEC ELECTRONICS SHALL NOT BE LIABLE UNDER THIS WARRANTY IF
ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT OR
MALFUNCTION IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUS-
TOMER’S OR ANY THIRD PERSON’S MISUSE, NEGLECT, IMPROPER INSTALLATION
OR TESTING, UNAUTHORIZED ATTEMPT TO OPEN, REPAIR OR MODIFY THE
PRODUCT, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE,
OR BY ACCIDENT, FIRE, LIGHTNING, OTHER HAZARDS, OR ACTS OF GOD.
LIMITATION OF LIABILITY : TO THE FULL EXTENT ALLOWED BY LAW, ACTION-
TEC ELECTRONICS ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABIL-
ITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR
INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF
ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF
INFORMATION OR DATA, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN
CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFOR-
MANCE, FAILURE, OR INTERRUPTION OF ITS PRODUCT, EVEN IF ACTION TEC
ELECTRONICS OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POS-
SIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACE-
MENT,OR REFUND OF THE PURCHASE PRICE PAID, AT ACTION TEC ELECTRON-
ICS’ OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE
AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL
PURPOSE.
Disclaimer : Some countries, states or provinces do not allow the exclusion or limitation of implied warranties or the limitation of incidental or consequential damages for certain products supplied to consumers, or the limitation of liability for personal injury, so the above limitations and exclusions may be limited in their application to you. When the implied warranties are not allowed to be excluded in their entirety, they will be limited to the duration of the applicable written warranty.
This warranty gives you specific legal rights which may vary depending on local law.
Dispute Resolution : The customer may contact the Director of Technical Support in the event the Customer is not satisfied with Action tec Electronics’ response to the complaint. In the event that the Customer is still not satisfied with the response of the Director of Technical Support, the Customer is instructed to contact the
Director of Marketing. In the event that the Customer is still not satisfied with the response of the Director of Marketing, the Customer is instructed to contact the
Chief Financial Officer and/or President.
17
Action tec Wireless Bluetooth Headset User Manual
Governing Law : This Limited Warranty shall be governed by the laws of the State of California, U.S.A., excluding its conflicts of laws and principles, and excluding the United Nations Convention on Contracts for the International Sale of Goods.
18
advertisement
Related manuals
advertisement