CRX14-DEMO-UPGRADE
USER MANUAL
Using UpGrade CRX14 Application V3.3 for
Upgrading your Reader USB CRX14 Demonstration Software
The
UpGrade CRX14 Application V3.3
software was developed to upgrade the firmware in Sector-1 of the
ST72F623F2M1 of the
Reader USB CRX14 Demonstration
hardware.
The
UpGrade CRX14 Application V3.3
kit consists of:
– One CD-ROM
– Documentation.
With
UpGrade CRX14 Application V3.3
software, you can:
■
■
Choose the reader that you want to program
Program up to 2 readers at a time
Application Features
■ RAM: 16Mbit
■
■
■
Free space: 2Mbit
USB version 1.1
Run on the Windows98 SE Platform, Windows2000, Windows XP
November 2003 1/6
CRX14-DEMO-UPGRADE - USER MANUAL
GETTING STARTED
Installing the UpGrade CRX14 Application V3.3 Software
■ Browse around the CD, and find the UpGrade CRX14 Application V3.3 folder.
■ After opening the folder, run the
setup.exe
program.
■ Choose your destination location. The default folder is C:\STContactless\UpGrade Application of
CRX14 USB Interface version 3.3
Figure 1. Chose Destination Location Screen
2/6
CRX14-DEMO-UPGRADE - USER MANUAL
■ Select your Program Folder. When you click on the “Next” button, the setup program will install the
UpGrade CRX14 Application V3.3 software.
Figure 2. Select Program Folder Screen
After clicking the next button the setup program will install the UpGrade application program.
2.2 Launching the UpGrade CRX14 Application V3.3 Software
Connect the (one or two) reader(s) to your PC. If you have USB Hubs, or if you have many USB Ports on your PC, you will still be limited by bandwidth, to a maximum of two devices. Run
UpGrade CRX14
Application V3.3
to launch the program. The upgrade screen (Figure 3) is displayed.
3/6
CRX14-DEMO-UPGRADE - USER MANUAL
Figure 3. Upgrade Screen
If you want to program all the devices (up to two at a time) click on the
Program all devices
button and push the
Run
button to begin the sequence.
If you want to program just one device, click on the
Program the device you want
button. Double-click on the device you want to select from the
Double click on the wanted device
area. Push the
Run
button to begin the sequence.
All the commands of the sequence are listed in the
Command performed
area. You can clear this window by clicking on the
Clear
button.
For example, for programming only one device, the commands performed are:
■
■
■
■
■
■
■
■
■
■
■
■
Vpp On: set the programming voltage at 12V.
Unlock: Unlock the Flash memory.
Erase: Erase all of Sector-1 (FFh)
Verify Block: Read Sector-1 and compare all the data to FFh.
Reset Device: Reset the device (Off/On).
Vpp Off: Set the supply voltage to 5V
Vpp On
Unlock
Flash Memory: Write in Sector-1 of the application.
Reset Device
Verify Block: Read Sector-1 and compare all the data with the original application.
Vpp Off
4/6
CRX14-DEMO-UPGRADE - USER MANUAL
REVISION HISTORY
Table 1. Document Revision History
Date
16-Jul-2003
24-Nov-2003
Version
1.0
1.1
Revision Details
First Issue.
Support of Windows WP added. Because of bandwidth, the maximum number of readers is 2. Illustrations updated from screen captures of v3.3 software.
5/6
CRX14-DEMO-UPGRADE - USER MANUAL
For current information on Contactless Memory products, please consult our pages on the world wide web:
www.st.com/contactless
If you have any questions or suggestions concerning the matters raised in this document, please send them to the following electronic mail addresses:
(for application support)
(for
Please remember to include your name, company, location, telephone number and fax number.
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
The ST logo is registered trademark of STMicroelectronics
All other names are the property of their respective owners
© November 2003 STMicroelectronics - All Rights Reserved
STMicroelectronics group of companies
Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong -
India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States.
www.st.com
6/6
