advertisement
USER'S MANUAL
1. TABLE OF CONTENTS
1. TABLE OF CONTENTS............................................................................................... 1
2. WARNINGS AND LABELS ......................................................................................... 2
2.1.
INSTRUCTIONS FOR MAINTENANCE, ADJUSTMENT AND SAFETY OF PEOPLE ..........................3
3. SYMBOLS ON THE MACHINE (DEPENDING ON THE MACHINE MODEL)............. 4
4. OPERATING INSTRUCTIONS .................................................................................... 6
4.1.
BEFORE WASHING................................................................................................................................6
4.2.
PROGRAM SELECTION.........................................................................................................................7
4.3.
WASH PROGRAMS OVERVIEW ...........................................................................................................8
4.4.
ADD DETERGENTS................................................................................................................................9
4.5.
START THE WASHER EXTRACTOR.....................................................................................................9
4.6.
END OF WASH CYCLE ........................................................................................................................10
4.7.
UNLOADING THE LINEN - CLEAN SIDE.............................................................................................10
4.8.
HOW TO OPEN DOOR WHEN FAILURE OCCURS............................................................................10
5. FIRST SERVICE AT TECHNICAL PROBLEM.......................................................... 11
1
2. WARNINGS AND LABELS
TO MINIMIZE THE RISK OF FIRE, INJURY BY ELECTRIC SHOCK OR SERIOUS INJURIES TO PEOPLE
OR PROPERTY DAMAGE, PLEASE READ AND FOLLOW THE FOLLOWING INSTRUCTIONS:
– This English version is original language version. Without this original version, these instructions are incomplete.
– Before installation, operation and maintenance of the machine read carefully the complete instructions, i.e. this „Installation, maintenance and user's manual“, „Programming manual“ and „Spare parts manual“.
The Programming manual and Spare parts manual are not delivered with a machine by default. You shall ask the supplier / manufacturer to obtain Programming manual and Spare parts manual.
– Follow the instruction written in manuals and keep the manuals in a proper place by the machine for later use.
– The washer extractor is designed for fabrics washing only, other objects can damage the machine and can cause damage or injuries.
– The manufacturer is not responsible for the damage to the fabrics that are washed by an inappropriate washing method.
– Always follow instructions and/or warnings that are stated on the fabrics, washing products or cleaning products mentioned by the manufacturer.
– If the machine is used for special applications follow the instructions and warning to avoid person injury.
– Keep the washer extractor surface and surrounding clean and free of flammable materials.
– Do not put fabrics treated with flammable products in the washer extractor. Such fabrics must first be washed by hand and air dried.
– Store laundry aids, dry-cleaning solvents and disinfectants out of the reach of children, preferably in a locked cabinet.
– Do not tamper the washer-extractor controls and follow the safety instructions and the warnings.
– Do not remove warning signs placed on the machine. Follow instructions on signs and labels to avoid personal injuries.
– Do not use some means on the soap dispenser lid to hold it open by filling or when the machine operates.
The discharge or splashing of hazardous liquid can cause serious scalding and burning.
– The use of hypochlorite will cause corrosion which may cause component failure under certain circumstances.
– The warranty of the machine cannot be accepted in case corrosion was caused by chlorine and chlorine compounds impact.
– Do not operate the washer extractor when parts are broken or missing or when covers are open.
The machine must not be operated until the fixed guards are put correctly in place.
– The washer extractor is not designed for work which may create an explosive atmosphere inside the machine and will not be used for this purpose.
– In case of steam escaping anywhere in the machine, shut off the main steam supply valve and call for maintenance.
– Under certain conditions, hydrogen gas may be created in the hot water system that has not been used for two or more weeks. Hydrogen gas is explosive. If the hot water system has not been used for such period, open all hot water taps and let the water run out for few minutes. This will release any accumulated gas.
As this gas is flammable, do not smoke or use open flames during this time.
– In case of danger turn off the main switch or other emergency disconnection devices.
– Turn off the main water supply at the end of each operating day.
– Only qualified service personnel can execute service on the washer extractor.
– Follow all valid and basic safety rules and laws.
– It is obvious that it is impossible to mention each possible risk in this manual. It is up to the user to proceed as careful as possible.
– The manufacturer reserves the right to change the manuals without previous notice.
– If a problem should arise, contact your dealer for assistance.
!
WARNING!
IF THE INSTALLED APPLIANCE OPERATE WITH COIN, TOKEN OR SIMILAR OPERATION FOR USE
IN SELF-SERVICE SITUATIONS, THEN THE OWNER-INSTALLER MUST PROVIDE A REMOTE-LOCATED
EMERGENCY STOP DEVICE. THIS DEVICE MUST BE PLACED IN SUCH A WAY THAT IT IS EASY
AND SAFELY ACCESSIBLE FOR THE USERS. THE EMERGENCY STOP DEVICE TAKES CARE
THAT AT LEAST THE CONTROL CIRCUIT OF THE APPLIANCE IS INTERRUPTED.
!
WARNING!
DO NOT TOUCH THE DOORGLASS UNTIL CYCLE HAS BEEN COMPLETED. DO NOT OPEN DOOR
UNTIL CYLINDER REMAINS STOPPED AND WATER HAS BEEN DRAINED FROM CYLINDER.
DO NOT PUT ARTICLES SOILED WITH EXPLOSIF SOLVENTS AND/OR DANGEROUS CHEMICAL
PRODUCTS IN THE MACHINE. THIS MACHINE SHOULD NOT BE USED BY CHILDREN.
DO NOT LET CHILDREN PLAY IN, ON, OR AROUND THE MACHINE. BEFORE TURNING THE MACHINE
„ON“, MAKE SURE THAT THERE ARE NO PEOPLE OR ANIMALS PRESENT IN OR AROUND THE MACHINE.
WARNING!
Always disconnect the washer from the electrical supply before attempting any service. The washer extractor is out of tension if the main plug is taken out or when the main supply is disconnected.
When the main switch is turned off the inlet terminals of the machine main switch are still under current!
CAUTION!
Extreme hot conditions can arise in the surroundings of this air.
Watch out for vapor that escapes from the washer extractor venting!
CAUTION!
Do not cover the washer extractor venting. It serves as a vapor outlet to prevent pressure building in the washer extractor.
!
WARNING!
ORIGINAL OR IDENTICAL PARTS MUST BE USED FOR REPLACEMENT IN THIS MACHINE.
AFTER SERVICING REPLACE AND SECURE ALL PANELS IN THE ORIGINAL WAY. TAKE THESE
MEASURES FOR CONTINUED PROTECTION AGAINST ELECTRICAL SHOCK, INJURY, FIRE
AND/OR PROPERTY DAMAGE.
!
WARNING!
SAFETY LABELS APPEAR AT CRUCIAL LOCATIONS ON THE MACHINE. FAILURE TO MAINTAIN
LEGIBLE SAFETY LABELS COULD RESULT IN INJURY TO THE OPERATOR OR SERVICE TECHNICIAN.
2.1. INSTRUCTIONS FOR MAINTENANCE, ADJUSTMENT AND SAFETY OF PEOPLE
Some important information for the usage of the machine are not (or only partly) mentioned in this „User’s manual“.
Missing information is possible to find in „Installation and maintenance manual“ according to the following references.
1. Manipulation, transportation, storage
2. Putting the machine into service
3. Technical specification
4. Putting the machine out of service
5. Description of the safe work system when maintenance is performed, adjustment, and when eliminating defects
6. Procedures on searching for defects, cleaning, maintenance
7. Heat risks
8. Description of qualities for ventilation
9. Loss of stability
10. Electric risks
11. Minimal water level
12. Sight holes
13. Water supply
3
3. SYMBOLS ON THE MACHINE
(DEPENDING ON THE MACHINE MODEL)
Caution, dangerous electrical tension, electrical devices
Caution, other danger, read and follow written instructions
Caution - Increased temperature
The machine is switched over to programming regime
Machine in operation
Press to unblock the door
Press to unblock the door
Transfer of heat in general
Do not close or cover
Do not put your hands on the marked area
Button of door locking
The machine hot air outlet
Signal of machine running (+ operating air pressure)
Button of activation of loading side
In case of emergency press the emergency button to stop the machine
Button of drum positioning
Signal of loading
The holes to be drilled not punched
Warm water inlet
(red color of the label)
Steam
Soft cold water inlet
(light blue color of the label)
Hard cold water inlet
(dark blue of the label)
Fig. 3.A Symbols on the machine
GRAPHITRONIC MICROPROCESSOR
START (advancing program)
STOP (interrupting program)
YES SELECTION
NO SELECTION
INCREASING SEQUENCE TIME
DECREASING SEQUENCE TIME
INFO (overview available wash programs and wash sequence functions)
SERVIS (shows actual water temperature and level, number of fulfilled cycles and actual states)
ACTIVATES THE TIME DELAY FUNCTION (delay time will be started by pressing start)
OPENING THE INLET VALVES
ACTIVATE HEATING
OPEN DRAIN VALVE
SPEED ADJUST
ENTER - SELECTION OR CONFIRMATION
Fig.3.B Symbols on the programmer keyboard
5
4. OPERATING INSTRUCTIONS
4.1. BEFORE WASHING
Sort the linen according to temperature and instructions determined by fabric manufacturer. Check if there aren‘t any strange objects between the linen like nails, screws, needles, etc. to prevent the washer-extractor or linen damage. Turn sleeves of shirts, blouses, etc. inside out. To get a better washing result mix the bigger and smaller pieces of linen and put them into the washer separately.
APPLICATED SYMBOLS
„A“ – valid for machines with capacity 70 kg / 160 lbs, 2 - chamber washing drum
„B“ – valid for machines with capacity 70 kg / 160 lbs, 3 - chamber washing drum
„C“ – valid for machines with capacity 90 kg / 200 lbs, 2 - chamber washing drum
„D“ – valid for machines with capacity 90 kg / 200 lbs, 3 - chamber washing drum
„E“ – valid for machines with capacity 110 kg / 245 lbs, 2 - chamber washing drum
„F“ – valid for machines with capacity 110 kg / 245 lbs, 3 - chamber washing drum
„G“ – valid for machines with capacity 140 kg / 310 lbs, 2 - chamber washing drum
„H“ – valid for machines with capacity 140 kg / 310 lbs, 3 - chamber washing drum
„I“ – valid for machines with capacity 180 kg / 400 lbs, 2 - chamber washing drum
„J“ – valid for machines with capacity 180 kg / 400 lbs, 3 - chamber washing drum
LOADING THE LINEN - DIRTY SIDE
Sort out the linen and weigh it according to following table:
CAPACITY
RATE 1:10 kg lb
2x35 3x23,3 2x45 3x30 2x55 3x36,6 2x70 3x46 2x90 3x60
2x77 3x51 2x99 3x66 2x121 3x80 2x154 3x101 2x198 3x132
KAPACITA
POMĚR 1:11 kg lb
2x31,8 3x21 2x40,9 3x27,2 2x50 3x33,3 2x63,6 2x41,8 2x81,8 3x54,5
2x70 3x46 2x90 3x60 2x110 3x73 2x140 3x91,8 2x180 3x120
Tab. 4.1.
516222A
Fig. 4.1.A, Machine
„I“, „J“
The following instructions are applicable for all machines
„A“, „B“, „C“, „D“, „E“, „F“, „G“, „H“, „I“, „J“:
1. Open an air supply.
2. Turn on the main switch, or possibly release the centralstop buttons.
On the loading side the following symbols will light up:
– operation pilot-light and instruction „Select Process“ occurs on the programmer display
– button for automatic turn of the washing drum
– button for opening the outer door
The following symbol will not light up:
– button for closing the outer door
The pilot lights of
loading are on at the unloading side.
3. Push the button for automatic turn of the washing drum. The washing drum is turned into the correct position and it is braked.
4. Push the button for opening the outer door. By this hook closure of the outer door is opened.
5. Open the outer door, the gas spring will lift the door up to the upper extreme position.
6. Opening the door of the washing drum, fig. 4.1.B:
– tilt the safety element, pos.2
– turn the segment lever, pos.1 to its extreme position outwards. This lever is moving approximately 90° outwards
– release the safety element, pos.2, the torsion spring will put it back to its original position
– now it is possible to open the washing drum door manually
7. Fill the washing drum chamber with appropriate quantity of linen according to table 4.1.
8. Closing the washing drum door, fig. 4.1.B:
– close the washing drum door manually
– tilt the safety element, pos.2
– turn the segment lever, pos.1, inwards to its extreme position
– release the safety element, pos.2, the torsion spring will put it back to safety position. Always care for the precise clamping the safety element, pos.2, by the stop, pos. 3. Then the washing drum door is closed correctly
9. Segment lever at the same time prevents the situation when the outer door drum is closed without shifting this lever back to closing position.
Fig.4.1.B
!
WARNING!
ALWAYS CARE FOR THE CORRECT CLOSING OF THE WASHING DRUM DOOR AND ESPECIALLY
FOR THE PRECISE CLAMPING OF THE SAFETY ELEMENT BEHIND THE SAFETY SHEET!
WARNING!
THE MACHINE MUST NOT BE PUT IN OPERATION UNLESS THE LOCK OF THE WASHING DRUM
DOOR AND SAFETY ELEMENT ARE NOT IN A GOOD CONDITION! NON-PERFORMANCE OF THE
SAFETY MEASURES CAN CAUSE THE MOST SERIOUS DAMAGES!
10. Close the outer door by pulling downwards, the gas spring will push the door to an extreme position inwards.
11. Push the button for closing the outer door. By this hook closure of the the outer door is locked.
!
WARNING!
ALWAYS CARE FOR THE CORRECT LOADING ALL CHAMBERS OF THE WASHING DRUM!
QUANTITY OF LINEN MUST NOT EXCEED THE MACHINE CAPACITY!
OVERLOADING CAN CAUSE POOR WASHING RESULT!
SMALL QUANTITY OF LINEN CAN CAUSE WRONG FUNCTION OF THE MACHINE!
4.2. PROGRAM SELECTION
Choose one of the available wash programs, best corresponding to the quality of linen and allowed wash temperature in the wash load. Selection of the program determines temperature and time for washing and rinsing.
Note: To change factory settings and/ or washing programs and for other settings options - see Programming manual.
7
4.3. WASH PROGRAMS OVERVIEW
Wash program 1:
Wash program 2:
Wash program 3:
Wash program 4:
Wash program 5:
Wash program 6:
Wash program 7:
Wash program 8:
Wash program 9:
Wash program 10:
Wash program 11:
Wash program 12:
Wash program 13:
Wash program 14:
Wash program 15:
Hot wash
Warm wash
90°C
60°C
Coloured wash 40°C
Bright coloured wash 30°C
Woollens
Hot wash
Warm wash
Coloured wash
15°C
90°C
60°C
40°C
ECONOMY level
ECONOMY level
ECONOMY level
Bright coloured wash 30°C ECONOMY level
Hot wash 90°C SUPER ECONOMY level
Warm wash
Coloured wash
60°C
40°C
SUPER ECONOMY level
SUPER ECONOMY level
Bright coloured wash 30°C SUPER ECONOMY level
Extraction low speed
Extraction high speed
LAYOUT OF WASH PROGRAM FOR MACHINE WITH RECYCLING TANKS AND FOR
SET WITH RECYCLING PROCESS
WASH PROGRAM 20: HOT WASH 90°C
Sequence Supply Inlet
Temp.
Level Wash action Time RPM
Top
Front
Top Front Top
Front
Step 1
Prewash Wash
Spin Spin
R=3“ min W
- - - - - - - 1 L
Wash Wash
Step 2
Drain Drain
- - - - - - - 30 D
Step 3
Step 4
Rinse 1
Spin
Rinse 2
Spin
Rinse 1
Spin
Spin
Rinse 2
2 W
- - - - - - L min
- - 2-5-6 1 - NH A=12“ R=3“ 2 min W
- - - - - -
L min
Step 5
Final
Rinse
Spin
Rinse 3 C D=30“ 1(+6) 1 - NL A=12“ R=3“ 3 min W
Spin - - - - - - - 6 H
Slowdown
- - - - - - - 1 -
Tumble
Note: If you want to drain the water to the recycling tank, select the drain valve DV2 in the drain step.
!
WARNING!
FOR TEMPERATURE HIGHER THEN 60°C, IS NOT POSSIBLE SET DRAINING TO RECYCLING TANK DV2.
!
WARNING!
IN CASE OF USING RECYCLING TANKS THE FUNCTION "TEMPERATURE BALANCE" MUST BE
ABORTED IN THE INSTALLATION MENU.
4.4. ADD DETERGENTS
Fill the soap dispenser at the side of the washer extractor depending of the chosen program.
Dispenser A: 1 st Wash
Dispenser B: 2 nd Wash
Dispenser D: Last Rinse
Add the detergents before the start of the wash cycle. The machine „
I“, „J“ has two bodies of soap hopper, see fig. 4.1.A. Always fill both hoppers with soap.
For washing machines connected to liquid soap supply system.
Check if the liquid soap supply system is in operation and if there is sufficient quantity of liquid soap.
Standard wash programs versus custom made wash programs.
This explanation is only valid for standard wash programs. For custom made programs, it is possible that other dispensers have been selected. (See „Programming manual“).
Remark
:
It is advisable to use only detergents with „reduced foaming“ which can easily be found in retail shops. The dosage of soap to use is generally mentioned on the packing. An overdose of detergent can lead to poor wash results and „suds“ overflow which can damage the machine. When contaminated laundry is washed, the effectiveness of germicide process depends on the type of laundry, degree of dirtiness, type of soap and structure of washing cycle. Take care that the lid of the soap dispenser is closed when the machine starts.
4.5. START THE WASHER EXTRACTOR
GRAPHITRONIC MICROPROCESSOR
After selecting the desired wash program number, by pressing the
START button the wash cycle will be started.
If there is no washing program available for the selected program number,
INVALID will be displayed.
Program
Number
Wash/Spin
Sequence
Wash Cycle
Name
Wash Cycle
Step
Units
Progression
Bar
Remaining Time
Wash Cycle
Door State
ATTENTION!
The program can only be started when the key switch is in Run Mode.
!
WARNING!
IF "NOT READY/DOOR" IS DISPLAYED, IT IS NOT POSSIBLE TO START WASHING CYCLE.
CHECK WHETHER:
- THE DRUM DOOR IS CLOSED
- THE PRESSURE OF COMPRESSED AIR SUPPLY IS IN PRESCRIBED RANGE.
CHECK ON THE MACHINE PRESSURE METER.
9
4.6. END OF WASH CYCLE
!
WHEN THE POWER SUPPLY HAS BEEN CUT, THE DOOR WILL BE AUTOMATICALLY BLOCKED
AGAINST OPENING. AFTER COOLING DOWN THE WASHING BATH, THE DOOR CAN BE OPENED
ACCORDING TO THE INSTALLATION AND MAINTENANCE MANUAL.
At the end of the wash cycle, when the remaining program time reaches „0“,
PROGRAM END is displayed.
When
UNLOAD appears on the display, the machine clean side is activated and you can unload the linen.
4.7. UNLOADING THE LINEN - CLEAN SIDE
1. On the machine clean side the following symbols will light up:
– button for automatic turn of the washing drum
– button for opening the outer door
Following symbols will not light up:
– button for closing the outer door
– signal light for loading
Perform procedure for positioning the washing drum and opening the door according to the chapters
4.1. points 3 to 6.
2. Unload a particular chamber of the washing drum.
Perform procedure for closing the door according to the chapters 4.1., points 8 to 11.
After unloading push the button for the
loading side activation . Doing this you activate the door on loading side. The signal light for loading is ON.
4.8. HOW TO OPEN DOOR WHEN FAILURE OCCURS
See Installation and maintenance manual.
5. FIRST SERVICE AT TECHNICAL PROBLEM
N°
Failure message Failure
Action
E1
No Drain Co
E2
No Drain
Drain failure Cooldown Full Stop + tumble
Drain failure Full Stop + tumble
E3
E4
E5
Tilt Fault
Imbalance
Tilt High Sp
Out of balance : Before spin
Out of balance : Normal spin
Out of balance : high spin
Full stop + tumble
Skip + continue
Full stop + safety time
E6
Door Coil
Door switch failure Full stop + safety time
E7
E8
E9
Door Switch
Door Start
Door Unload
Door solenoid switch failure
Door lock check at start failure
Door lock switch closed failure
Full stop + safety time
Don’t start
Don’t start
E10
Bimetal/Spring
Bimetal/Spring Continue
E11
No Fill
Fill failure
Full stop + request for
Continue
E12
Overfill
E13
No Heating
Overfill failure
Heating failure
Full stop + tumble
Full stop + tumble
E14
Heat Time
Heating time failure
Full stop + request for
Continue
E15
Too Hot
E21
Overflow
E22
Flush fault
E24
Level Sens
Too Hot
Overflow failure
Flush failure
Full stop + tumble
Full stop + tumble
Full stop + tumble
Defective level sensor Continue + Don’t start
E25
E26
Temp Sensor
Mitsub code
Defective temperature sensor
Undefined frequency inverter error code
Continue + Don’t start
Full stop + tumble
E27
Comm fault
Communication fault inverter
Full stop + safety time
E28
THT time / E.OL
THT Time out / E.OL Full stop + safety time
E29
OV3 time / E.OP
OV3 Time out / E.OP Full stop + safety time
E31
Load Parr
Initialization fault inverter
Don’t start
E32
E33
E35
E37
E38
E39
E40
E41
E42
E43
E44
E45
Verify Parr
Stall prev
Wrong Softw
No Drain Sp
No Recycle
Out of Soap
No Fill Rec
Service Due
Connection
Voltage Par
Model type
No Speed Sensor
Signal
Verification fault inverter
Stall prevention function active
Don’t start
Continue
Wrong software version Don’t start
Drain failure at the
Spray Sequence
Full stop + tumble
The Tank with recycle water is empty
Warning at the End.
Front soap dispenser
Mach. only
The Soap Supplies are running Out of Soap
For Info only
Fill failure due to an empty water recycle
Tank
Service Due Warning
Full stop + Request for
Continue
Top soap dispenser Mach. only
For Info only
Open door = reset
No Network
Connection
Wrong Voltage Range
Selection
Wrong Inverter Model
Type
No Speed pulses when drum turns.
For Info only
Make correct selection
Make correct selection
Continue + Warning
E46
Brake Closed
Brake Stays Closed Full stop + safety time
Fault occurrence
Draining sequence Cooldown
Draining sequence
Start spin
After 10 x tilt
>500 or 750 RPM
Whole cycle
Whole cycle
At start up
End cycle
2 min 30 sec after start cycle
While filling
While filling
While heating
While heating
While heating
Wash step
Flush step
Before start up
Before start up
Whole cycle
Whole cycle
At spin sequence
At spin sequence
At initialization
At loading parameters
At spin sequence
New software version
Spray Sequence
Wash step
Wash step
Wash step
End cycle
Data Transfer Networking
Configuration menu
Configuration menu
At spin sequence
(FS120 only)
At spin sequence
(FS120 only)
11
E47
Brake Wear Out
Friction blocks brake are wear-out
Brake Stays Open
Full stop + safety time
E48
Brake Open
Continue + Warning
E49
E50
E51
E52
E53
E57
E58
E59
E60
UnBalance Switch
At Wash
No Second
Acceleration Ramp
No Third
Acceleration Ramp
Board Memory
Board Data
Lock System
No Free Run
Run Free Run
No reset Drive
Air suspension without compressed air
Missing wire bridge inverter / wrong inverter parameters
Missing wire bridge inverter / wrong inverter parameters
PCB-EEPRROM CRC failure
PCB-EEPROM Data out of range failure
Door Lock Switch stays closed when the outer door is open.
Deceleration end of spin while brake is closed.
Run Status inverter =1 while brake is closed.
No detection motor speed signal at wash
E61
Continue spin
Motor doesn't stop spinning anymore
E62
Extended speed
Motor spins too fast
E63-
E67
Motor Drive
Reset Motor Drive for
E60, E61 & E62
E68
E69
No Sign Spin
RS Unbalance
No detection motor speed signal at spin
Unbalance input should not be high on R machines
E70
E71
E72
E73
E74
E75
E78
E79
E80
E81
RS7 Select
RS10 Select
KEB ST LOW
KEB ST HIGH
CFIStuck
KEB code
Lock Active
Lock Start
Time Out Input16
No Reheat
RS7 selected in case of
RS10
RS10 selected in case of
RS7
No wire bridge terminals
16-20
No KEB parameters loaded in inverter
Inverter not switched off at end of cycle.
Undefined frequency inverter error code
At standby door lock is locked nevertheless door is open.
After pressing Start door lock is locked nevertheless door is open.
On Hold Signal Failure
Soap Dispensing
System
Heating Failure
E82
E83
E84
No Refill
Cycle Fail
No Store PC
Refill failure
No successful wash cycle termination
Communication failure with PC
Full stop + safety time
Continue
Continue
Don't start
Don't Start
Don’t Start
Full stop + safety time
Full stop + safety time
Full stop + safety time
Full stop + safety time
Full stop + safety time
Reset Motor Drive
Full stop + tumble
Don't Start
Full stop + tumble
Don't Start
Don't Start
Don't Start
Full stop + safety time
For Info only
Full stop + tumble
Don't Start
Don't Start
Full stop + tumble.
Full stop + tumble.
Full stop + request for
Continue
Info that the wash cycle has to be repeated.
For Info only.
At Start Cycle
Whole cycle
Wash Step
(MB only)
Wash Step
(MB only)
Abnormal Cycle Termination
(MB only)
End cycle
(MB only)
Any time
(FS120 only)
At spin sequence
(FS120 only)
Wash action
(FS120 only)
At spin sequence
(FS120 only)
At spin sequence
(FS120 only)
At Power Up
At Power Up
At locking sequence
(MB70-90-110-140-180 only)
At spin sequence
(FS120 only)
At spin sequence
(FS120 only)
Wash Sequence
Whole cycle
Whole cycle
Wash Sequence
Spin Sequence
Start Spin sequence
Whole cycle
Start Cycle
Start Cycle
Start cycle
Start cycle
End of cycle
Whole cycle
At Standby
E85
RTC Low Batt
E86
No RTC Comm
E100 Weigh No Comm
Real Time Clock, No
Battery or battery low power
Real Time Clock is not available
Communication fault weighing system
For Info only.
For Info only.
Full Stop Tumble
E101 Weigh Low
E102 Weigh High
E103 Weigh Balance
E104 Weigh Overload
E105
Weigh Airbags
E300-
E353
E400-
E441
MITS ERR
KEB ERR
E500-
E515
MEMORY ERR
E550
DAQ VERSION
ERR
E551
E552
E553
DAQ WRITE
ERR
DAQ FULL
ERR
STORE
DAQ>PC
E600-
E628
SOFTW ERR
Weight machine is too low
Weight machine is too high
Weight is not balanced over 4 load cell's.
Weight on individual load cell exceeds max.
No functional air pressure system
Specific Mitsubishi
Inverter Alarm
Specific KEB Inverter
Alarm
Don't Start
Don't Start
Don't Start
Full Stop Tumble
Don't Start
Full stop + safety time
Full stop + safety time
Memory Error
Full stop + safety time
Wrong DAQ Memory version
Problem writing DAQ
Memory
DAQ Traceability
Memory is Full
DAQ Traceability
Memory is almost Full
Software Error
For Info only
For Info only
For Info only
For Info only
Full stop + safety time
End cycle
(MB only)
End cycle
(MB only)
Before Start (MB16-MB180)
Whole Cycle (MB16-MB66)
(MB & FS23-55 only)
Before Start
(MB & FS23-55 only)
Before Start
(MB & FS23-55 only)
Before Start
(MB & FS23-55 only)
Whole Cycle
(MB16-66 & FS23-55 only)
Before Start
(MB70-180 only)
Whole cycle
Whole cycle
Any time
Installation new softw
Traceability function, whole cycle
Traceability function, whole cycle
Traceability function, whole cycle
Any time
13
INSTALLATION AND MAINTENANCE MANUAL
1. CONTENTS
1. CONTENTS..................................................................................................................... 1
2. IMPORTANT SAFETY INSTRUCTIONS ........................................................................ 2
2.1. SYMBOLS ON THE MACHINE ...............................................................................................................4
2.2. IMPORTANT INFORMATION BEFORE INSTALLATION.......................................................................4
3. TECHNICAL SPECIFICATION ....................................................................................... 5
3.1. WASHERS 70 kg / 160 lb, 90 kg / 200 lb, 110 kg / 245 lb ...............................................................................5
3.2. WASHERS 140 kg / 310 lb, 180 kg / 400 lb..............................................................................................7
3.3. DIMENSIONS AND COMPONENTS OF THE MACHINE..........................................................................9
4. INSTALLATION ............................................................................................................ 10
4.1. HANDLING, TRANSPORT AND STORAGE.........................................................................................10
4.2. SPACE REQUIREMENTS.....................................................................................................................12
4.3. MACHINE POSITIONING......................................................................................................................12
4.4. CONNECTIONS ....................................................................................................................................15
4.5. PUTTING THE MACHINE IN OPERATION ..........................................................................................22
5. MAINTENANCE ............................................................................................................ 24
5.1. INTRODUCTION ...................................................................................................................................24
5.2. DAILY.....................................................................................................................................................24
5.3. ONCE A MONTH OR AFTER 200 OPERATION HOURS ....................................................................24
5.4. EVERY 3 MONTHS OR AFTER 500 OPERATION HOURS ................................................................24
5.5. EVERY 6 MONTHS OR AFTER 1000 OPERATION HOURS ..............................................................25
5.6. SAFETY VIBRATION SWITCH .............................................................................................................25
5.7. TIGHTENING MOMENTS .....................................................................................................................26
5.8. LUBRICATION.......................................................................................................................................26
5.9. DRIVING MECHANISM .........................................................................................................................27
5.10. WATER AND STEAM FILTERS ..........................................................................................................28
5.11. SEALING OF MAIN BEARINGS - DRIP PANS...................................................................................28
5.12. BRAKE.................................................................................................................................................28
5.13. REPLACEMENT WASHER FUSES ....................................................................................................29
5.14. EARTH LEAKAGE TRIPS OF THE LAUNDRY...................................................................................29
5.15. MAGNETIC SENSORS - ARRESTING OF OUTER DOOR, SECURITY SWITCH...........................................29
5.16. SECURITY SAFETY EQUIPMENT FOR THE OUTER DOOR...........................................................30
5.17. SENSOR FOR SETTING THE AUTOMATIC POSITION OF THE INNER DOOR..................................30
6. TROUBLE SHOOTING AIDS........................................................................................ 31
6.1. DOOR BLOCKING.................................................................................................................................31
6.2. ERROR INDICATION SHOWN ON DISPLAY.......................................................................................31
7. LIST OF RECOMMENDED SPARE PARTS................................................................. 32
8. PUTTING THE MACHINE OUT OF SERVICE.............................................................. 33
8.1. DISCONNECTING THE MACHINE.......................................................................................................33
8.2. MACHINE DISPOSAL ...........................................................................................................................33
513289_D_PUB_DATE_1_DEC_2011.DOC INSTALLATION AND MAINTENANCE MANUAL 1
2
2. IMPORTANT SAFETY INSTRUCTIONS
WARNING - SAVE THESE INSTRUCTIONS FOR LATER USE.
Failure to comply with the instructions may lead to incorrect use of the appliance, and may result in risk of fire, bodily injuries or death and/or damage to the laundry and/or the appliance.
WARNING - Read the IMPORTANT SAFETY INSTRUCTIONS in this manual carefully before operating the appliance. Improper use of the appliance may cause risk of fire, electrical shock or serious body injuries or death as well as serious damage to the appliance.
This English version is the original version of this manual. Without this version, the instructions are incomplete.
Before installation, operation and maintenance of the machine read carefully the complete instructions, i.e. this „Installation, maintenance and user's manual“, „Programming manual“ and „Spare parts manual“.
The Programming manual and Spare parts manual are not delivered with a machine by default.
You shall ask the supplier / manufacturer to obtain Programming manual and Spare parts manual.
Follow the instruction written in manuals and keep the manuals in a proper place by the machine for later use.
Safety instructions included in manuals for personnel operating the appliance must be printed and posted on a visible place near the machine in the laundry room.
The washer extractor is designed for fabrics washing only, other objects can damage the washer and can cause damage or injuries.
The manufacturer is not responsible for the damage to the fabrics that are washed by an inappropriate washing method.
Always follow the instructions and/or warnings that are stated on the fabrics, washing products or cleaning products mentioned by the manufacturer.
The washer must be set up in accordance with the instructions. All drain, inlet, electrical connections, ventilation, groundings and other connections must be done in according to the installation manual, in compliance with the local standards done by qualified technicians with proper authorization.
The valid standards for connecting to the local power network (TT,TN,IT,..) must be followed.
In the standard execution, the appliance may not be suitable for connecting to an IT supply system.
Contact your commercial distributor for assistance.
All appliances are produced according the EMC-directive (Electro-Magnetic-Compatibility). They can be used in restricted surroundings only (comply minimally with class A requirements). For safety reasons there must be kept the necessary precaution distances with sensitive electrical or electronic device(s).
Do not change the parameters of the frequency inverter. This can cause serious injury, fire, washer damage, etc.
During transportation and storage never use excessive forces on the packing because components can be damaged protruding the contour line of the appliance.
Use copper conductors only. This appliance must be connected to a supply circuit to which no lighting units or general-purpose receptacles are connected.
Any changes concerning the installation which are not described in this Installation Manual must be approved by the supplier or manufacturer. Otherwise, the supplier and manufacturer are not responsible for potential injuries to operators or for any damages. Interventions in the appliance execution or functions are not allowed, and the manufacturer refuses any responsibility in such cases.
The washer extractor must be installed on level. If not, the washer may become unbalanced during extraction and, although fitted with an unbalance safety, the washer may become seriously damaged what may result in bodily injuries.
Never put the washer in operation when the transporting braces are not removed. The washer should always be tested before use.
It is possible that there are residues of products used during the production process in the new washer.
These residues could cause stains on your laundry. Therefore, you must first run at least 1 hot wash with old rags before using for your normal laundry.
Keep the appliance top and surface and the area around clean and clear of combustible or flammable products.
Do not store flammable materials around the appliances. Define the dangerous areas in the laundry room and obstruct an admission to them during appliances operating.
Do not wash articles that have been previously cleaned in, wash in soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances as they give off vapors that could ignite or explode.
Do not add gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water.
These substances give off vapors that could ignite or explode.
Under certain conditions, hydrogen gas may be created in the hot water system that has not been used for two or more weeks. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such period open all hot water taps and let the water run out for few minutes. This will release any accumulated gas. As this gas is flammable, do not smoke or use open flames during this time.
INSTALLATION AND MAINTENANCE MANUAL 513289_D_PUB_DATE_1_DEC_2011.DOC
TEMPERATURE IN WASHING MACHINE TUB: The electronic controller uses the temperature sensor in the tub to control the temperature of the washing bath. There are a lot of things that have influence on the temperature measurement. Therefore the temperature control of the washing bath is not very precise.
Always strictly comply with the instructions that are written on the laundry chemicals-, laundry aids-, dry-cleaning solvents- and disinfectants packaging to avoid personal injury. Keep these agents out of the reach of children, preferably in a locked cabinet.
Do not tamper the washer-extractor controls and do not bypass the safety instructions and the warnings.
Do not use some means on the soap dispenser lid to hold it open by filling or when the machine operates.
The discharge or splashing of hazardous liquid can cause serious scalding and burning.
Do not operate the appliance when parts are broken or missing or when covers are open. The appliance must not be operated until the fixed guards are put correctly in place.
The appliance must not be stored, installed or exposed to the weather, extreme low or high temperature and humidity levels. Do not hose down the washer. NEVER allow the appliance to get wet.
Check the functioning of the door lock mechanism on regular base. NEVER bypass the doorlock mechanism.
Disconnect the power and close all water and steam supply before cleaning, servicing and at the end of each operating day.
Out of the venting on the upper part of the washer can escape warm vapor or and hot air. Do not cover the vent but protect it sufficiently. It serves air gap and as a vapor outlet to prevent pressure building in the washer.
Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in the service manual or published user-repair instructions that you understand and have the skills to carry out.
Only qualified service personnel may open the appliance to carry out servicing.
Information contained in this manual is intended for use by a qualified service technician familiar with proper and safe procedures to be followed when repairing an electrical appliance. All tests and repairs should be performed by a qualified service technician equipped with proper tools and measuring devices. All component replacements should be made by a qualified service technician using only factory approved replacement parts.
Improper assembly or adjustment may occur if service or repair is attempted by persons other then qualified service technicians or if parts other then approved replacement parts are used. Improper assembly or adjustment can create hazardous conditions.
There can be a risk of injury or electrical shock while performing services or repairs. Injury or electrical shock can be serious or even fatal. Consequently, extreme caution should be taken while performing voltage checks on individual components or a product. PLEASE NOTE: Except as necessary to perform a particular in servicing a product, the electrical power supply should ALWAYS be disconnected when servicing a product.
All industrial (OPL - On Premise Laundry) washers are designed for use in Laundry with professionally trained attendants.
Before the appliance is removed from service or discarded, remove the door.
Any Water or Steam Leaks Must Be Repaired Immediately. Closed supply immediately.
If any problems or failures should arise, immediately contact your dealer, serviceman or manufacturer.
The manufacturer reserves the right to change the manuals without previous notice.
!
WARNING -- CAUTION
This appliance must be connected to a grounded metal, permanent wiring system, and additionally an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance.
!
WARNING -- CAUTION
In order to minimize the risk of fire, electrical shock and injury, THIS WASHER MUST BE PROPERLY
GROUNDED. Never plug in or direct-wire an appliance unless it is properly grounded in accordance with all local and national codes.
If more appliances in the same location, mutual grounding must be applied where possible.
!
WARNING -- CAUTION
The washer extractor is intended to be permanently connected, it MUST be secured mounted to a NON-COMBUSTIBLE, adequate floor structure. A concrete foundation is required. Metal reinforced wood floors are NOT allowed due to the risk of fire and excessive vibrations.
NEVER install the washer on an upper floor or over a basement without a load support designed by a structural engineer.
!
WARNING - Although the appliance may be in the „off“ position, there is still electrical power to the switch supply terminals.
!
WARNING - When power supply has been switched off wait for at least 10 minutes before starting inspection or servicing the washer. Before starting inspection of frequency inverter, check for residual voltage across main circuit terminals + and -. This voltage must be below 30 VDC before you can access the inverter for inspection.
513289_D_PUB_DATE_1_DEC_2011.DOC INSTALLATION AND MAINTENANCE MANUAL 3
!
WARNING - Do not allow children to play on, in or around the appliance at any time. Close supervision of children is necessary when the appliance is used near children. Never permit children to operate the appliance.
!
WARNING - Do not open door until cylinder remains stopped and water has been drained completely.
If the door safety lock does not work, do not use washer until the door lock mechanism is repaired.
!
CAUTION
! -
Follow all valid basic safety rules and laws. The instructions in this manual cannot account for every possible dangerous situation. They must be generally understood. Caution and care are factors which can not included in the design of the appliance and all persons who install, operate or maintain the appliance must be qualified and familiar with the operating instructions. It is up to the user to take proper care when operating the appliance.
!
CAUTION
! -
Do not remove warning signs placed on the appliance. Observe signs and labels to avoid personal injuries. Safety labels appear at crucial locations on the appliance. Failure to maintain legible safety labels could result in injury to the operator or service technician.
CAUTION
! -
If the installed appliance operate with coin, token or similar operation for use in self-service situations, then the owner-installer must provide a remote-located emergency stop device. This device must be placed in such a way that it is easy and safely accessible for the users. The emergency stop device takes care that at least the control circuit of the appliance is interrupted.
2.1. SYMBOLS ON THE MACHINE
Warning, read and keep written instructions
Dangerous electric current, electric appliance
Direction of the drum rotation during prewash + wash
Direction of the drum rotation during spin and moving round a slight amount
Press the emergency button in danger
4
2.2. IMPORTANT INFORMATION BEFORE INSTALLATION
FOR TRANSPORTATION AND STORAGE
IN CASE OF TRANSPORTATION AND STORAGE, WATCH COMPONENTS PROTRUDING FROM THE
CONTOUR LINE OF MACHINE (DOOR LOCKS ETC.), TO AVOID INJURIES.
– Never push, pull or exert pressure on components protruding from the machine contour line (controls, door locks etc.).
– Make sure that these components are secured so as to avoid damages during machine manipulation and installation.
– In case of the machine transportation by the customer, follow the manufacturer's instructions for transportation, handling and storage of the product. In case of transportation of machine by the customer the manufacturer is not responsible for possible damage of machine in the course of transportation. In case of storage the machine in a free area it must be protected against mechanical damage and weather condition factors.
FOR INSTALLATION
ALL CONNECTION, AND IN SPECIAL PROTECTING EARTH, MUST BE PERFORMED BY QUALIFIED
PERSONNEL WITH A PROPER AUTHORIZATION ACCORDING THE INSTALLATION MANUAL IN COMPLIANCE
WITH LOCAL STANDARDS.
– The washer must not be installed or stored in an area where it will be exposed to water and/or weather.
Avoid damp conditions where water or moisture could run down the walls and covers of the washer or cover the floor around the washer. Do not install the washer above an open gutter. Close any nearby gutters so that waste water steam cannot collect near/inside the washer.
– Any changes in the machine installations must be approved by manufacturer. Otherwise the manufacturer is not responsible for possible injuries or damages. Interference and changes in the machine construction are not allowed and the manufacturer refuses any responsibilities in such cases.
– Define dangerous areas in the laundry room and do not allow people to enter if the machine is in operation.
MACHINE INFORMATION
– This manual contains information for the barrier or non barrier spring-mounted machine with load of dry linen 70kg / 160lb,
90 kg / 200 lb, 110kg / 245lb, 140 kg / 310 lb, 180 kg / 400 lb.
– Verify the machine model according to your order and the data plate located, on the cover of the machine, near the filling door and find corresponding information in the manual.
– The machine is controlled by an electronic control. Find the programming instructions in the programming manual.
– Additional heating can be provided by electrical heating elements or by steam from an external steam supply.
– Water inlets can use warm, cold soft and cold hard water. A machine can be equipped with a recycled discharging, extend the quantity of dosing pumps and the soap hopper.
– The machine has 5 hoppers, (10 hoppers, valid for 180 kg / 400 lb) filled from the side part of the washing machine, fig. 3.3., pos.26.
INSTALLATION AND MAINTENANCE MANUAL 513289_D_PUB_DATE_1_DEC_2011.DOC
3. TECHNICAL SPECIFICATION
3.1. WASHERS 70 kg / 160 lb, 90 kg / 200 lb, 110 kg / 245 lb
DRY LOAD CAPACITY:
loading ratio 1/10 loading ratio 1/11 kg / lb kg / lb
70 / 154
63 / 139
90 / 198
83 / 183
110 / 242
100 / 220
MACHINE DIMENSIONS
(1)
Width
Depth
Height mm / inch mm / inch mm / inch
2025 / 79,72
1615 / 63,58
1805 / 71,06
2275 / 89,56
1615 / 63,58
1805 / 71,06
2325 / 91,53
1615 / 63,58
1855 / 73,03
PACKING DIMENSIONS
Width
Depth
Height
Transportation volume mm / inch mm / inch mm / inch m³ / ft³
2100 / 82,67
1740 / 68,50
1985 / 78,14
7,3 / 258
2355 / 92,71
1740 / 68,50
1985 / 78,14
8,1 / 286
2400 / 94,48
1740 / 68,50
2080 / 81,88
8,7 / 307
INNER DRUM DIMENSIONS
Type
Number of chambers
Diameter
Depth
Drum volume
Door opening mm / inch mm / inch dm³ / gal mm / inch dividing Y / Pullman
2 / 3
1000 / 39,36
900 / 35,43
700 / 184 dividing Y / Pullman
2 / 3
1000 mm / 39,36“
1150 mm / 45,27“
900 / 237
765 x 340 / 30,11 x 13,38 dividing Y / Pullman
2 / 3
1100 mm / 43,30“
1200 mm / 47,24“
1100 / 291
WEIGHT
Net
Gross kg / lb kg / lb
2600 / 5732
2760 / 6085
2810 / 6195
2970 / 6548
2990 / 6592
3150 / 6945
ELECTRICAL DATA
Power supply - deviations
Motor output
Power supply system capacity kW kVA
INPUT POWER
Electrical heating 54 kW
Electrical heating 72 kW
Electrical heating 96 kW
Steam or without heating
Rated heating input power
(electrical heating only) kW kW kW kW
SUPPLY PROTECTION DEVICE
Residual current device (RCD) mA
Steam or without electrical heating
200 - 240V 3AC
380 - 480V 3AC
A
A
El. heating 54 kW (380-480V 3AC) A
El. heating 72 kW (380-480V 3AC) A
El. heating 96 kW (380-480V 3AC) A
3x380-480V 50/60Hz
3x200-240V 50/60Hz
-6% do +10% of the voltage supply ±1 Hz
11 steam heating: 20 electrical heating 54kW: 70 electrical heating 72kW: 88
60
54kW, 72kW
15 steam heating: 28 el. heating 72kW: 93 el. heating 96kW: 120
-
78 85
- 109
11,5 15,5
72kW, 96kW
Use „slow“ type Protection devices (circuit breakers: curve D)
63
32
100
100, class B
160
-
WASHING FUNCTIONS
Washing RPM 36
Distribution RPM
Low extraction RPM
60
550
High extraction RPM 800
Tab.3.1.
75
50
-
160
35
754
513289_D_PUB_DATE_1_DEC_2011.DOC INSTALLATION AND MAINTENANCE MANUAL 5
DRY LOAD CAPACITY:
loading ratio 1/10 loading ratio 1/11
G-factor:
Low extraction
High extraction
CONNECTION
Water inlet connection kg / lb kg / lb inch
Water pressure range MPa / bar / PSI
Maximal water temperature °C / °F
Drain diameter mm / inch
Drain flow rate dm³.min
-1
gal.min
-1
Drain connection - applicable for wash bath sample inch
Steam connection inch
Steam pressure MPa / bar / PSI
Press air connection mm / inch
Air pressure MPa / bar / PSI
Powder dispenser cups
Liquid soap signals
Number of liquid soap supply system connection points
Venting connection of outer drum mm / inch
CONSUMPTION
Steam
Average kg.hour
-1
/ lb.hour
ANCHORING
Anchoring bolt
(2)
-1
70 / 154
63 / 139
68 / 150
170
360
90 / 198
83 / 183
1 x ½“ - applicable for wash bath sample
G 1“
0,6 - 0,8 / 6 - 8 / 87 - 116 internal Ø10 / 0,4“
0,6 / 6 / 87
5 internal G½“
1 outer Ø115 / 4 ½“
82 / 181
4 pcs, M20x350
GENERAL DATA
Ambient temperature
Relative humidity
Height above sea level
Storage temperature
Emission: emitted heat
Dynamic force amplitudes during extraction
°C / °F m / ft
°C / °F kW
Max. static loading of the floor by weight of the machine and filler kN
Static load on floor during extraction kN kN
Frequency of dynamic load Hz
31,57
27,12
± 1,06
13,4
5 to 35 / 41 to 95
30% to 90% without condensation up 1000 / 3280
1 to 55 / 34 to 131
7
35,67
29,54
± 1,24
13,4
SOUNDS LEVELS
(3)
L
Aeq extraction seq. db 76
Tab.3.1.continuation
(1)
maximum dimensions including protruding parts
(2)
depend on related wash parameters
(3)
ISO 3744
110 / 242
100 / 220
186
350
BSP 3 x 1,5“ / 1 x ¾“
0,3 - 0,6 / 3 - 6 / 43 - 87
90 / 194
1 x Ø126 / 5 (standard) - to the drain
+ 1 x Ø126 / 5 (according to the request) - to the recycling tank
600
158
102 / 225
39,47
31,66
± 1,41
12,6
85
6 INSTALLATION AND MAINTENANCE MANUAL 513289_D_PUB_DATE_1_DEC_2011.DOC
3.2. WASHERS 140 kg / 310 lb, 180 kg / 400 lb
DRY LOAD CAPACITY:
loading ratio 1/10 loading ratio 1/11 kg / lb kg / lb
MACHINE DIMENSIONS
(1)
Width mm / inch
Depth
Height mm / inch mm / inch
PACKING DIMENSIONS
Width mm / inch
Depth mm / inch
Height
Transportation volume mm / inch m³ / ft³
INNER DRUM DIMENSIONS
Type
Number of chambers
Diameter
Depth
Drum volume
Door opening mm / inch mm / inch dm³ / gal mm / inch
WEIGHT
Net
Gross kg / lb kg / lb
ELECTRICAL DATA
Power supply - deviations
Motor output kW
Power supply system capacity kVA
INPUT POWER
Electrical heating 72 kW
Electrical heating 96 kW
Steam or without heating
Rated heating input power
(electrical heating only) kW kW kW
SUPPLY PROTECTION DEVICE
Residual current device (RCD) mA
Steam or without electrical heating
200 - 240V 3AC
380 - 480V 3AC
A
A
El. heating 72 kW (380-480V 3AC) A
El. heating 96 kW (380-480V 3AC) A
WASHING FUNCTIONS
Distribution RPM
Low extraction RPM
High extraction RPM
140 / 308
127 / 280
2435 / 95,86
1805 / 71,06
2075 / 81,69
2485 / 97,83
1940 / 76,37
2250 / 88,58
10,8 / 381
180 / 396
163 / 360
2585 / 101,77
1905 / 75
2165 / 85,23
2665 / 104,92
2040 / 80,31
2265 / 89,17
12,3 / 434 dividing Y / Pullman
2 / 3
1200 / 47,24 dividing Y
3
1300 / 51,18
1250 / 49,21
1400 / 369,8
765 x 440 / 30,11 x 17,32
1400 / 55,11
1800 / 475,5
3550 / 7826
3760 / 8289
4990 / 11001
5310 / 11707
3x380-480V 50/60Hz
3x200-240V 50/60Hz
-6% do +10% of the voltage supply ±1 Hz
18,5 22 steam heating: 34 electrical heating 72kW: 100 electrical heating 96kW: 125 steam heating: 41
-
-
91 -
115 -
19 22,5
72kW, 96kW -
Use „slow“ type Protection devices (circuit breakers: curve D)
100, class B
100
63
160
200
100
75
-
-
720
Tab.3.2.
36
60 55
550
695
513289_D_PUB_DATE_1_DEC_2011.DOC INSTALLATION AND MAINTENANCE MANUAL 7
DRY LOAD CAPACITY:
loading ratio 1/10 loading ratio 1/11 kg / lb kg / lb
140 / 308
127 / 280
180 / 396
163 / 360
WASHING FUNCTIONS
G-factor:
Low extraction
High extraction
CONNECTION
Water inlet connection inch
Water pressure range MPa / bar / PSI
Maximal water temperature
Drain diameter
°C / °F mm / inch
Drain flow rate dm³.min
gal.min
-1
-1
Drain connection - applicable for wash bath sample
Steam connection inch inch
Steam pressure
Press air connection
MPa / bar / PSI mm / inch
Air pressure MPa / bar / PSI
Powder dispenser cups
Liquid soap signals
Number of liquid soap supply system connection points
Venting connection of outer drum mm / inch
220
5
350
1 x Ø126 / 5 (standard) - to the drain
+ 1 x Ø126 / 5 (according to the request) - to the recycling tank
600
158
1 x ½“ - applicable for wash bath sample
G 1“
0,6 - 0,8 / 6 - 8 / 87 - 116 internal Ø10 / 0,4“
0,6 / 6 / 87 internal G½“
1 outer Ø115 / 4 ½“
217
BSP 3 x 1,5“ / 1 x ¾“ BSP 3 x 1,5“ / 1 x 1“
0,3 - 0,6 / 3 - 6 / 43 - 87
90 / 194
10
CONSUMPTION
(2)
Steam
Average kg.hour
-1
/ lb.hour
-1
135 / 298 176 / 388
ANCHORING
Anchoring bolt
GENERAL DATA
Ambient temperature
Relative humidity
°C / °F
Height above sea level
Storage temperature
Static load on floor
(intermittent vibrations) m / ft
°C / °F
Emission: emitted heat kW
Max. static loading of the floor by weight of the machine and filler kN kN
Dynamic force amplitudes during extraction
Frequency of dynamic load kN
Hz
SOUNDS LEVELS
(3)
L
Aeq extraction seq. db
4 pcs, M20x350
5 to 35 / 41 to 95
30% to 90% without condensation
48,75
37,74
± 1,53 up 1000 / 3280
1 to 55 / 34 to 131
7
64
52,78
± 1,98
12 11,6
80
Tab.3.2.continuation
(1)
maximum dimensions including protruding parts
(2)
depend on related wash parameters
(3)
ISO 3744
8 INSTALLATION AND MAINTENANCE MANUAL 513289_D_PUB_DATE_1_DEC_2011.DOC
3.3. DIMENSIONS AND COMPONENTS OF THE MACHINE
1. Hard cold water inlet
15. Button of door unlocking
16. Button of drum positioning
2. Soft cold water inlet
3. Hot water inlet
17. Button of door locking
4. Steam inlet
18. Main switch
5. Supply of pressure air
6. Power supply
7. Main drainage valve
19. Door of unloading (clean size)
20. Signal of loading
21. Centralstop
8. Recycling drainage valve
22. Button of door locking
9. Venting of the machine
23. Button of activation of loading side
10. Door of loading (dirty side)
11. Programmer
24. Button of door unlocking
25. Button of drum positioning
12. Change-over switch
13. Signal of machine running (+ operating air pressure)
26. Soap hoppers
27. Soft cold water inlet into soap hoppers
28. Liquid detergent inlet
14. Centralstop
Fig.3.3. Placement of components on the machine (dimensions are given in mm)
513289_D_PUB_DATE_1_DEC_2011.DOC INSTALLATION AND MAINTENANCE MANUAL 9
4. INSTALLATION
4.1. HANDLING, TRANSPORT AND STORAGE
TRANSPORT AND STORAGE
!
WARNING!
FORKS OF HIGH LIFTING TRUCK MUST HAVE SUFFICIENT LENGTH (SEE FIG. 4.1.A).
For handling the machine in packing, use the fork lift truck or four (alternatively two) manual pallet trucks.
The machine pallet is designed for handling in both (mutually vertical) directions, see fig. 4.1.B. and 4.1.C.
– If possible, leave the machine in the transporting package or at least let it set on the transporting wooden skid until the time of final installation on the foundation according the chapter 4.3. of this manual.
Dimension „X“, see tab.3.1., 3.2
Machine width or depth - according to direction of handling.
Fig.4.1.A Minimum length „X“ of lift truck forks for machine model
2x MANUAL PALLET TRUCK
2x MANUAL PALLET TRUCK
Fig.4.1.B. Handling in direction of loading and unloading
Fig. 4.1.C. Handling in direction of the pulley side and inlet valves side
HANDLING DURING INSTALLATION
All activities can be done only by a worker, who knows all information about the machine. Machine is delivered to the customer in a wooden packing or wooden crate and protected with polyethylene film. The machine is attached to the skid by means of four bolts.
To remove the machine to its final position follow these precautions:
– All passages and spaces the machine has to be transported through at installation should be reasonably dimensioned to meet the height and width of the machine including the package.
– Never push, pull or press the components protruding from the contour line of machine (front part
of the machine, filling door, control elements, belt cover, water inlet and outlet pipes etc.).
MAKE SURE THAT THESE COMPONENTS ARE SECURED SO AS TO AVOID THEIR DAMAGE DURING
HANDLING AND INSTALLATION OF THE MACHINE.
10 INSTALLATION AND MAINTENANCE MANUAL 513289_D_PUB_DATE_1_DEC_2011.DOC
– Make sure that the filling door are secured to avoid its opening during the handling.
– Lift the machine up by the fork-lift truck or by pallet trucks using a transport skid to which the machine has been attached.
UNPACKING
After unpacking, check if the machine has not been damaged and if all the accessories are included according to your order. Verify the machine model according to your order and the data plate located, on the cover of the machine, near the filling door and find corresponding information in the manual. Manual and accessories are placed inside the drum which is possible to open according to chapter 6.1.
Before the machine is installed on the place, remove the packing, remove the frontal and side covers and remove four screws which fix the machine to the pallet. According to fig.4.1.D., use the lifting feet (4pcs), (1) and fix them using the bolts M12 (2) to the machine frame.
(Feet and bolts are being the part of delivery).
For fixing the feet it is possible to use the following combination of positions:
– loading side (dirty) + unloading side (clean)
– side of pulley + side of inlet valves
Lift the machine up carefully using the pallet trucks and remove the wooden skids. Now, install the machine on its final position carefully and remove the feet. Keep the feet for possible handling later on.
CLEAN SIDE
DIRTY SIDE
Fig.4.1.D. Lifting feet
HANDLING WITH HUNG MACHINE
In case of need and under certain conditions, it is possible to handle the machine in hanging position.
All activities can be done only by a worker, who knows all information about the machine. Use four-point suspension with recommended length of arm 1700 - 1800 mm / 67 - 71“ for handling the machine in hanging position. Four-point suspension must have minimum load capacity 10000 kg / 22046 lb. Do not use any loops
(danger of the box damage and electric distributor damage). If the machine is handled in hanging position, it must be hung on all four lifting eyes, fig. 4.1.E., pos.1. The machines are equipped with lifting eyes or holes
Ø 30 mm / 1,18“ located on the front of the machine (according the machine model). During the handling with machine in suspension, transport braces must be attached to the machine.
513289_D_PUB_DATE_1_DEC_2011.DOC INSTALLATION AND MAINTENANCE MANUAL 11
Fig.4.1.E. Hanging eyes for the hook suspension
4.2. SPACE REQUIREMENTS
REQUIRED MACHINE WORKING CONDITIONS
See chapter „3. TECHNICAL SPECIFICATION“.
The washer must not be installed or stored in an area where it will be exposed to water and/or weather.
Avoid damp conditions where water or moisture could run down the walls and covers of the washer or cover the floor around the washer. Do not install the washer above an open gutter. Close any nearby gutters so that waste water steam cannot collect near/inside the washer.
SIZE OF A LAUNDRY ROOM
IGNORING THE REQUIREMENT FOR SPACES BETWEEN MACHINES AND WALLS CAN MAKE
SERVICE AND MAINTENANCE WORK DIFFICULT.
Total space requirements for the system installation are usually determinate by a detailed plan of the building.
The machine dimensions are stated in the chapter „3. Technical specification“. Leave min. 0,8 m / 31,49“ free space between the machine left side and the wall, where the machine stands for the maintenance access.
Also between the machine right side and the wall or another machine leave free space minimally 0,8 m / 31,49“, see fig. 4.3.B. The waste piping or outlet channel must be dimensioned to the discharged water quantity and a number of washing machines.
4.3. MACHINE POSITIONING
CARRYING CAPACITY OF THE FLOOR
!
WARNING!
IT IS RECOMMENDED TO CONSULT STATIC REQUIREMENTS WITH A STATIC ENGINEER TO MEET
THE REQUIREMENTS OF PERMISSIBLE LOADING, VIBRATIONS AND NOISE LEVEL IN THE BUILDING!
FASTENING THE MACHINE
!
WARNING!
THE MACHINE MUST ALWAYS BE FIXED TIGHTLY TO THE FLOOR AND MUST FIT RELIABLY
TO THE FLOOR IN ALL FOUR SPOTS INTENDED FOR FIXING THE MACHINE!
The machine is to be located on a levelled concrete floor to comply with static and dynamic stress of the machine.
Check the position of the machine base frame by a water level. The manufacturer is not responsible for consequences caused by a wrong installation. Find a location for the anchoring bolts for the fixation of the machine on the floor, see fig.4.3.A.
12 INSTALLATION AND MAINTENANCE MANUAL 513289_D_PUB_DATE_1_DEC_2011.DOC
Fig.4.3.A
!
WARNING!
THE NUTS OF THE ANCHORING BOLTS HAVE TO BE TIGHTENED BY MEANS OF A TORQUE,
SEE FIG.4.3.A. DO NOT TIGSHTEN NUTS OF ANCHORING BOLTS BEFORE THE CONCRETE BASE
AROUND THE BOLTS IS COMPLETELY HARDENED.
513289_D_PUB_DATE_1_DEC_2011.DOC INSTALLATION AND MAINTENANCE MANUAL 13
Fig.4.3.B Installation plan
***
14 INSTALLATION AND MAINTENANCE MANUAL 513289_D_PUB_DATE_1_DEC_2011.DOC
RECYCLING
DRAIN
VALVE
MAIN DRAIN
VALVE
Fig.4.3.C. Basement plan
4.4. CONNECTIONS
CONNECTION OF WATER SUPPLIES
The washer is equipped with 1,5“ BSP (British Standard Pipe Thread) hot and cold water inlet valves, indicated by a sticker next to the inlet. For connection dimensions see fig.3.3. Use the water inlet hoses that accompany the washer as they are properly adapted to the water valves and appliance. Machines with a dosing vessel have a separate supply of cold water into the soap hopper G ¾“, valid for machines 70 kg / 160lb, 90 kg / 200 lb, 110kg /
245lb, 140 kg / 310 lb. Machines 180 kg / 400 lb have a separate supply of cold water into the soap hopper G 1“.
NEVER use a rigid connection to the water supply.
The 1“ inlet hoses have on both side BSP thread. To connect them to a NPT installation, an adapter is available.
For best operation of the washer, it is necessary to keep the water pressure within the limits stated in the chapter „3. TECHNICAL SPECIFICATIONS“. Water pressure that is below minimum requirements can lengthen the wash cycle or/and not allow proper function of the washer.
It is also necessary to connect ALL available water inlets to a water supply. If a hard water supply is not present, connect it with soft cold water. If no hot water supply is present, contact your dealer for the proper required action.
513289_D_PUB_DATE_1_DEC_2011.DOC INSTALLATION AND MAINTENANCE MANUAL 15
TO INSTALL
Flush the water system in order to remove any particles that may be in the water system.
Install on the washer the filter device, normally delivered with the washer. Connect to this the inlet water hose with appropriated seal washer where necessary.
When connecting inlet hoses, be sure hose connections are not cross-threaded on the connection devices.
Tighten the hoses securely. DO NOT over tighten as this will damage threads on the device(s).
The water hardness can have an influence on the wash results. The soap supplier can help you with making the right decisions concerning hard water, soft water, washing programs, type of soap and other related items to give the best wash results.
HOT WATER
IMPORTANT -- TEMPERATURE IN WASHING TUB
The electronic controller uses the temperature sensor in the tub to control the temperature of the washing bath.
There are a lot of things that have influence on the temperature measurement. Therefore the temperature control of the washing bath is not very precise. In principle, the manufacturer strives that the real temperature inside the washer is never higher than the programmed temperature so that textile linen will not be damaged because of too high temperature. If for certain applications a very precise washing bath temperature is necessary, appropriate measures must be taken, see Programming manual.
The manufacturer will refuse any responsibility for all consequences because of inaccurate temperatures inside the washing machine tub.
The hot water supply needs to be large enough to provide the required hot water for the installed washers.
For good wash results we advise a hot water supply that is set between 140 - 160°F / 70 - 80°C. To determinate the boiler capacity you can use the data of the water amount in the tub depending on programmed water level stated for individual machine model in Programming manual. Please be aware that boiler capacity depends on boiler temperature, linen, program set up and washing program used.
WATER CONSUMPTION
The water consumption depends on the programmed values in the controller. These default values can be found in the programming manual. For a wash the low water level is used. The high water level is used for rinsing.
The programmed units correspond to an average amount of water. You can calculate the total water consumption in one washing program by counting up the amount of water by each washing step.
Be aware that the values received from this calculation is only an estimation of the real water consumption.
The deviation depends on many circumstances. In the wash cycle for example there will be taken a mix of warm water and cold water. The mix of the water depends on the temperature of both. The total amount of water consumed depends also on the loading, type of linen and the drum rotation.
COLD HARD - COLD SOFT - HOT WATER
COLD SOFT - HOT WATER
COLD SOFT WATER
INLET INTO SOAP
HOPPERS
COLD SOFT WATER
INLET INTO SOAP
HOPPERS
COLD HARD
COLD SOFT
HOT WATER
COLD SOFT WATER
INLET INTO SOAP
HOPPERS
COLD HARD
COLD SOFT
HOT WATER
COLD SOFT
HOT WATER
COLD SOFT WATER
INLET INTO SOAP
HOPPERS
COLD SOFT
HOT WATER
Fig. 4.4.A
1. Cold hard water
2. Cold soft water
3. Hot water
16 INSTALLATION AND MAINTENANCE MANUAL 513289_D_PUB_DATE_1_DEC_2011.DOC
WATER DRAIN CONNECTION
Washing machine is equipped with one drain valve (the second drain valve for recycle drain can be added per order) which must be connected to the waste sump. Position of drain valves, see on fig. 3.3., pos.7, 8.
The waste sump must be located lower than the drain pipes because the water discharges from the machines by gravity. Do not reduce the diameter of the machine drain pipes. To connect the machine drainage to a waste sump, you can use the flexible hose (part of delivery). Secure the flexible hose with a clamp.
Seal the connecting point of the drain pipe and flexible hose with silicon cement. In same way connect the flexible hose to waste sump throat, fig.4.3.C.
PRESSURE AIR CONNECTION
The distribution of the compressed air of the machine terminates on the air board, see fig.3.3., pos.5 at the connecting plastic coupling. Connect the pressure air supply from the laundry distribution system to this pipe. (After dismantling the plastic coupling, the compressed air can be connected to the inside thread
G1/4“.) Operator must install the manual stop-valve into the supply piping. The machine needs compressed air with pressure min. 6 bar to control the valves. Pressure 6 bar should be set on the inlet valve (with regulator and manometer). The pressure switch is set for 4 bar. Set the reduction valve of air springs to 5 bar, applicable for 70 kg / 160 lb, 90 kg / 200 lb, 110 kg / 245 lb, 140 kg / 310 lb. Set the reduction valve of air springs to 3,5 bar - applicable for 180 kg / 400 lb.
VERSION WITH WEIGHING SYSTEM:
In the case of a machine with a weighting system, the second pressure switch is set for 4,5 bar, valid for machines 70 kg/ / 160lb, 90 kg / 200 lb, 110kg / 245lb, 140 kg / 310 lb.
For machines 180 kg / 400 lb the second pressure switch is set for 3 bar.
STEAM CONNECTION
!
WARNING!
INSTALL A STEAM SUPPLY DISCONNECTING DEVICE IN THE VINICITY OF EACH WASHER.
DISCONNECT THE STEAM SUPPLY ALWAYS BEFORE ANY SERVICE OR INTERVENTION, GIVING
SUFFICIENT TIME TO COOL DOWN THE PARTS TO AVOID INJUIRES.
!
WARNING!
BEFORE EVERY STEAM VALVE IT IS NECESSARY TO INSERT THE FILTER WITH PERMEABILITY
UP TO 300 MICROMETERS. POSSIBLE DIRT BIGGER THAN 300 MICROMETERS MIGHT DAMAGE
THE STEAM VALVE AND CAUSE ITS LEAKAGE.
!
WARNING!
IF THE STEAM SUPPLY IS EXECUTED FROM ABOVE, MOREOVER THERE MUST BE AUTOMATIC
DRAINAGE PLACED BEFORE THE STEAM VALVE!
For dimensions of steam connection information, see fig.3.3., and technical information table.
Use an inlet steam pressure hoses only, adapted to the steam valve with appropriate seal that is suitable for the applied working pressure.
Take care that by the installation and connection of the steam supply the necessary measure are taken that accidental contact is prevented, this for all persons. Due to the high temperature, direct injury will appear.
To enable a possible dismantling of the steam valve, equipped the attaching point with a connector.
Install the steam piping up to the machine steam valve with fall in direction of flow. This piping should be drained in its deepest spot.
VENTING
!
WARNING!
VAPOURS ESCAPE FROM THE MACHINE THROUGH THE AIR VENT OPENING!
(FIGURE 3.3., POSITION 9) DO NOT COVER.
The vent air opening is part of the back flow prevention water system. It also takes care that the tub can not be pressurized by water intake and vapor of the hot water. It allows also proper measuring of the water level.
For the safety of everyone make sure that unauthorized persons cannot reach the backside of the machine.
Notwithstanding the fact that it is not advised and if measures were taken, you can connect the machine venting pipe to the laundry central duct for exhausting the vapor out of the building. For placing of connection points see fig.3.3. The piping material must withstand a temperature of 80°C / 176°F and generated machine vibrations. The central duct for multiple venting must be dimensioned for the total cross section of venting pipes of all machines. Take care that this installation can not create any injury at anyway.
513289_D_PUB_DATE_1_DEC_2011.DOC INSTALLATION AND MAINTENANCE MANUAL 17
ELECTRICAL
CONNECTION
The machine has been designed for connecting to the power network according the specification of your order.
Before connection check the voltage values and the frequency stated in the machine label if they correspond to your power network. The data plate is located on the cover of the machine near the filling door. An individual branch circuit needs to be used for each machine. The way of the connection is described in fig.4.4.B. For electrical protection, there must be installed a residual current device (RCD) and a circuit breaker in the electrical installation of the building (laundry switchboard). For correct selection see below.
IMPORTANT:
- If the machine is not equipped with a main switch then supply disconnecting devices need to be provided in the installation for all electrical supplies connected to the machine, in accordance with EN 60204-1 standard, point 5.3.
- Make sure the supply voltage is always within the limits specified in the „3. Technical specification“ table in all circumstances. When you have long distances in the electrical installation, it may be necessary to use bigger cables to reduce the voltage drop.
- When the machine is connected near a large capacity power supply transformer (500kVA or more, wiring length
shorter than 10 m) or there is a power capacitor switch-over, a power supply improving reactor must
be installed. If you do not install this, the inverter may get damaged. Contact your sales office for more info.
!
WARNING!
GROUNDING: IN EVENT OF MALFUNCTION OR BREAKDOWN OR LEAKAGE CURRENT,
THE GROUNDING WILL REDUCE THE RISK OF ELECTRICAL SHOCK AND SERVE AS A PROTECTING
DEVICE, BY PROVIDING A PATH OF LEAST RESISTANCE OF ELECTRICAL CURRENT.
THEREFORE IT IS VERY IMPORTANT AND THE RESPONSIBILITY OF THE INSTALLER TO ASSURE
THE WASHER IS ADEQUATELY GROUNDED AT THE POINT OF INSTALLATION TAKING
INTO CONSIDERATIONS THE NATIONAL AND LOCAL CONDITIONS AND REQUIREMENTS.
1. Residual current device (RCD)
2. Laundry electrical switchboard
3. Supply protection device
4. Washing machine
5. Phase conductors
6. Protective conductor
7. Main switch inlet terminal switchboard
Fig.4.4.B. Machine connection to electrical network (with an earth leakage trip)
RESIDUAL CURRENT DEVICE (RCD)
In some countries an RCD is known as an „earth leakage trip“ or „Ground Fault Circuit Interrupter“ (GFCI) or an „Appliance Leakage Current Interrupter“ (ALCI) or „earth (ground) leakage current breaker“.
Specifications:
– Tripping current: 100mA (if locally not available/allowed use a 30mA trip current, preferably selective type with small time delay set)
– Install max. 2 machines on each RCD (for 30mA, only 1 machine)
– Type B. There are components inside the machine which make use of DC-voltages and therefor a „type B“
RCD is necessary. For information only: Type B is better preformance than type A, and type A is better than type AC.
18 INSTALLATION AND MAINTENANCE MANUAL 513289_D_PUB_DATE_1_DEC_2011.DOC
– When locally allowed, there must always be installed an RCD. In some power network earthing systems
(IT, TN-C,…), an RCD might not be allowed (see also IEC 60364).
– The machine control circuits are mostly supplied by a separating transformer. Therefore the RCD may not detect faults in the control circuits (but the fuse(s) of the separating transformer will).
SUPPLY PROTECTION DEVICE
A supply protection device basically protects the machine and wiring against overloads and short circuits.
As supply protection device, you can use either (glow-wire) fuses or (automatic) circuit breakers.
See the table „Technical specifications“ for the rating of the nominal current and other specifications of the supply protection device. In this table there is specified that the protection must be the „slow“ type, for circuit breakers this means curve D. Although not recommended, if for some reason you can not use a slow type, select the protection device with 1 step higher nominal current rating to avoid disconnecting during start-up.
SUPPLY CABLE
The supply cable is not delivered with the machine.
Specifications:
– Conductors with copper cores.
– Stranded conductors are strongly recommended (flexible wiring) to avoid conductor breaking because of vibration.
– THE CROSS SECTION DEPENDS ON THE USED SUPPLY PROTECTION DEVICE. SEE TABLE 4.4.A,
FOR THE MINIMAL CROSS SECTION.
– As short as possible, directly from the supply protection device to the machine without branching off.
– No plug or extension cords: The machine is intended to be permanently connected to the electrical network.
Connection:
– Insert the cable through the hole in the on the rear panel, insure a strain relief (turnbuckle) is used so that the supply cable can not move.
– Strip the conductor ends according fig.4.4.C.
– The protective conductor must be longer so that when the cable is pulled out accidentally, this conductor is disconnected the last one!
– With stranded conductors, use „wire end tubes“ with an insulated sleeve (6) for L1/U, (L2/V), (L3/W), (N) conductors. Make sure there can not be accidental contact, since the supply cable stays under voltage even when the main switch is off.
– Crimp a ring terminal (eyelet) to the protection conductor for good fixation to the PE terminal.
– Connect the supply cable conductors to the terminals (main switch (1)) marked with L1/U, (L2/V), (L3/W),
(N), and the terminal (copper screw) marked with PE, see fig 4.4.D.
– Provide a sag in the cable, in front of the cable strain relief. This will avoid ingress of condensed water into the machine, see fig 4.4.D.
Power supply protection device nominal current (US)
Min phase conductor section in mm² (AWG)
Min Protection conductor section in mm² (AWG)
Automatic circuit breakers
A
16 (15)
20 (20)
25 (-)
40 (40)
Fuses
A
10 (10)
16 (15)
20 (20)
32 (30)
1.5 (AWG 15)
2.5 (AWG 13)
4 (AWG 11)
6 (AWG 9)
63(-) 50 (50) 10 (AWG 7)
80 63 16
100 80 25
125 100 35
160 125 50
200 160 70
250 200 95
300 250 120
1.5 (AWG 15)
2.5 (AWG 13)
4 (AWG 11)
6 (AWG 9)
10 (AWG 7)
16
16
25
35
50
70
95
Tab.4.4.A Manufacturer's recommended minimal conductor section
513289_D_PUB_DATE_1_DEC_2011.DOC INSTALLATION AND MAINTENANCE MANUAL 19
MACHINE
70 kg / 160 lb
90 kg / 200 lb
110 kg / 245 lb
140 kg / 310 lb
180 kg / 400 lb
SUPPLY
VOLTAGE
MAX. CURRENT
HEATING TYPE
(A)
steam 29 electrical 54 kW 99
3AC 400V
electrical 72 kW 118
3AC 230V
steam 50
3AC 400V
steam 29 electrical 54 kW 99 electrical 72 kW 122
3AC 230V
steam 50 steam 40
3AC 400V
electrical 72 kW 122 electrical 96 kW 157
3AC 230V
steam 69 steam 49
3AC 400V
electrical 72 kW electrical 96 kW
130
168
3AC 230V
steam 85
3AC 400V
steam 59
3AC 230V
steam 95
Tab.4.4.B
1. Protection conductor
2. Phase conductor
3. Phase conductor
4. Phase conductor
5. Moulding tube
6. The stripped length of conductors
Fig.4.4.C Adaptation of conductor ends of supplying cable
1. Main switch
2. Turnbuckle
3. -
4. Sag of inlet cable
Fig.4.4.D Connection of main power inlet
20 INSTALLATION AND MAINTENANCE MANUAL 513289_D_PUB_DATE_1_DEC_2011.DOC
advertisement