A10 Harmony Controller 2000 Installation Manual

PDF

Documento

Anuncio

1 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

Information in this document is subject to change without notice.

Patent Protection

A10 Networks products are protected by patents in the U.S. and elsewhere. The following website is provided to satisfy the virtual patent marking provisions of various jurisdictions including the virtual patent marking provisions of the America Invents Act. A10 Networks' products, including all Thunder Series products, are protected by one or more of U.S. patents and patents pending listed at: https://www.a10networks.com/company/legal-notices/a10-virtual-patent-marking .

Trademarks

The A10 logo, A10 Harmony, A10 Lightning, A10 Networks, A10 Thunder, aCloud, ACOS, Affinity, aFleX, aFlow, aGalaxy, aGAPI, aVCS, AX, aXAPI, IDsentrie, IP-to-ID, SSL Insight, SSLi, Thunder, Thunder TPS, UASG, and vThunder are trademarks or registered trademarks of A10 Networks, Inc. in the United States and other countries. All other trademarks are property of their respective owners.

Confidentiality

This document contains confidential materials proprietary to A10 Networks, Inc. This document and information and ideas herein may not be disclosed, copied, rep ro duced or distributed to anyone outside A10 Networks, Inc. without prior written consent of A10 Networks, Inc.

A10 Networks Inc. Software License and End User Agreement

Software for all A10 Networks products contains trade secrets of A10 Networks and its subsidiaries and Customer agrees to treat Software as confidential information.

Anyone who uses the Software does so only in compliance with the terms of the End User License Agreement

(EULA), provided later in this document or available separately. Customer shall not:

reverse engineer, reverse compile, reverse de-assemble or otherwise translate the Software by any means

sublicense, rent or lease the Software.

Disclaimer

This document does not create any express or implied warranty about A10 Networks or about its products or services, including but not limited to fitness for a particular use and non-infringement. A10 Networks has made reasonable efforts to verify that the information contained herein is accurate, but A10 Networks assumes no responsibility for its use. All information is provided "as-is." The product specifications and features described in this publication are based on the latest information available; however, specifications are subject to change without notice, and certain features may not be available upon initial product release. Contact A10 Networks for current information regarding its products o r services. A10 Networks’ products and services are subject to A10 Networks’ standard terms and conditions.

Environmental Considerations

Some electronic components may possibly contain dangerous substances. For information on specific component types, please contact the manufacturer of that component. Always consult local authorities for regulations regarding proper disposal of electronic components in your area.

Further Information

For additional information about A10 products, terms and conditions of delivery, and pricing, contact your nearest

A10 Networks location, which can be found by visiting www.a10networks.com

2 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

Getting Started

..................................................................................................... 5

Inspection

................................................................................................................................. 5

Interface Connections

............................................................................................................. 6

Harmony Controller 2000 Interfaces

.................................................................................... 7

Using the Interface Connections

........................................................................................... 7

LED Locations and Status Indicators

................................................................................... 7

Installation

................................................................................................................................ 8

Power-On

.................................................................................................................................. 9

Power Supply Unit Installation

......................................................................... 10

Overview

.................................................................................................................................. 11

DC Power Supply Installation

............................................................................................... 12

Power Supply Hot Swap

....................................................................................................... 13

Removing a Power Supply

................................................................................................... 13

Inserting a Power Supply

...................................................................................................... 14

Fan Hot Swap

..................................................................................................... 16

Fan Module Location and Fan Numbers

............................................................................ 16

Removing a Fan Module

....................................................................................................... 16

Inserting a Fan Module

......................................................................................................... 18

Rack Mount Kit Installation

.............................................................................. 20

Ear Bracket Installation

......................................................................................................... 20

Front Mount Installation

....................................................................................................... 20

Power Supply Product Specifications

............................................................ 24

750W AC Power Supply Specifications

.............................................................................. 24

750W DC Power Supply Specifications

.............................................................................. 24

3 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

4 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

Getting Started

This guide describes how to physically install the A10 Harmony

This chapter contains the following topics:

Controller 2000, and how to configure the management (MGMT) interface for network access to the Command-Line Interface (CLI).

• Inspection

• Interface Connections

• LED Locations and Status Indicators

• Installation

• Power-On

Inspection

Inspect the box carefully before opening it. If the box is damaged, contact the shipper for instructions on filing a claim. Opening a damaged box before inspection by the shipper will void any potential shipping claims.

CAUTION: Do not attempt to install or operate damaged equipment. As with any electrical equipment, personal injury or damage to other equipment can result from commissioning damaged electrical equipment.

Lithium-Ion Battery Warning

CAUTION: There is a danger of explosion if a lithium battery is replaced with an incorrect type. Ensure that your replacement battery is of the same or equivalent type recommended by the manufacturer. Follow manufacturer’s instructions for disposal of used batteries.

Regulations

Follow all applicable regulations for installation of electrical equipment.

Unpacking

Carefully unpack your Harmony Controller Appliance and included items from the box.

5 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

Check the Contents

Confirm that the following items are included with the Harmony Controller Appliance:

• Cables: two power cables, one Serial to RJ-45 console cable, 1x Cat5e Ethernet cable

• Hardware: bracket ears for rack mount installation

Specifications for the equipment rack are listed in Table 2 .

Rack-mount installation instructions are available in “ Rack Mount Kit Installation” .

Other Requirements

Other equipment needed for installation:

• Notebook or workstation PC (Windows, Linux, Mac) with compatible Ethernet connectivity

• Supported Web browser

• Terminal Emulation Software (PuTTy, HyperTerminal, or similar)

Interface Connections

This section contains the following:

• Harmony Controller 2000 Interfaces

• Using the Interface Connections

6 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

Harmony Controller 2000 Interfaces

The Harmony Controller 2000 model provides the following interfaces:

• Management Interfaces

• 1 serial console interface ( Console )

• 1 Ethernet interface ( Mgmt ) for remotely managing the device over the network

FIGURE 1 Harmony Controller 2000 Interface Locations and Numbers

Using the Interface Connections

To begin using these interface connections:

Connect the serial cable to the serial console interface.

Connect an Ethernet cable to the MGMT interface.

LED Locations and Status Indicators

Figure 4 summarizes the locations of the LEDs on your system.

7 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

FIGURE 2 LED Locations

Table 1 describes the LED status indicators.

TABLE 1 LED Status Indicator Descriptions

LED Color

POWER Green

STATUS

HDD

Amber

Green

Status

Off

Description

Power is switched ON

Power Off

System Initializing

System under access

No power access

HDD under access

No Data access

Installation

Table 2 describes the minimum requirements for your equipment rack. Verify these specifications against your equipment prior to installing the chassis.

TABLE 2 Equipment Rack Specifications and Part Numbers

Item Rack Mount Kit

Part Number ASK-RACKMOUNT-011

Item Description 2 or 4-Post Rack Mount Kit

2-Post Installation Yes

4-Post Installation Yes

4-Post Depth N/A

Mounting Thread No

Double 4-Post

Default Bundle

Notes

Yes

Included in accessory box

8 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

Power-On

The device automatically boots when the power plug is connected to an electrical outlet. If the unit does not boot automatically, it can be manually booted by quickly flipping the power switch .

NOTE: Power OFF – To perform a graceful shutdown, use the shutdown command in the CLI. If you made any changes to the device configuration, you will be prompted to save your configuration information before the device powers down.

Force Power OFF – If the system stops working and requires a forced shutdown, press and hold the power switch for four seconds. Keep in mind that this forced shutdown will cause a loss of configuration information that has not be manually saved.

9 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

Power Supply Unit Installation

This guide describes how to connect the power supply unit to an applicable AC or DC power source.

The following topics are covered:

• Overview

• DC Power Supply Installation

• Power Supply Hot Swap

NOTE: Follow all applicable regulations for installation of electrical equipment; for example, in the United States of America, the National Electrical Code.

For devices with multiple power supplies, it is recommended that all power supplies be plugged-in.

10 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

Overview

AC or DC power connections are made using standard connections. AC or DC power is connected to each module separately.

Power connections are made using a hot-swap power cable, which enables quick and easy installation of the power supplies without the need to disturb the terminal blocks. For models with multiple power supply units, power is connected to each module separately.

Before extracting a power supply from the chassis, you must disconnect it from the power source. This is required regardless of whether the power supply is in standby mode or powered on mode. Likewise, when installing a power supply, insert the power supply into the chassis first, before connecting the power supply to the power source.

• Insertion: Input and Output power are connected simultaneously, in either standby mode or powered on mode, when the power supply is inserted into the chassis.

• Extraction: Input and Output power are disconnected simultaneously, in either standby mode or powered on mode, when the power supply is extracted from the chassis.

No damage or arcing to Input or Output contacts occurs.

FIGURE 3 Example of AC Power Supply by itself, and with power cable connected.

11 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

DC Power Supply Installation

Refer to the following instructions and figures for this procedure. (Also see figures on previous page.)

Attach Green wire to ground for both ends.

Attach BLACK -48 volt wire to -48 volt pin on DC power source for both ends.

Attach RED return wire to return pin on DC power source for both ends.

FIGURE 5 DC Power Supply Cable.

12 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

Power Supply Hot Swap

Follow the directions in the following sections to remove and insert a power supply unit.

FIGURE 7 Power Supply Hot Swap

Removing a Power Supply

To remove a power supply:

Push and hold the panel to unlock the lock (A).

Hold the panel and pull out the power supply

13 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

Inserting a Power Supply

To insert a power supply:

Push the power supply into the slot.

Plug the power cable into the power supply.

14 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

15 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

Fan Hot Swap

This chapter provides fan hot swap instructions for the device.

The following topics are covered:

• Fan Module Location and Fan Numbers

• Removing a Fan Module

• Inserting a Fan Module

Fan Module Location and Fan Numbers

The location and number of each fan is shown in Figure 8 .

Removing a Fan Module

Follow the steps below in order to remove and replace a fan module ( Figure 9 and Figure 10 ).

Loosen the two screws on the back end of the chassis.

16 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

FIGURE 9 Removing the Top Panel to Access Fan Modules

Hold both screws, then pull them outward to slide the top panel out.

Lift to remove the top panel.

CAUTION : Operation on or for this device should only be done in a fixed location such as a lab or data center.

17 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

Remove the two screws of the appropriate fan module to remove it.

Remove the fan module.

Inserting a Fan Module

Follow the steps below in order to insert a fan module.

Insert the fan module into the appropriate location.

Tighten the two screws to secure the fan module.

Note : Top panel must be removed to access fan modules. See Removing a Fan Module for instructions on removing the top panel.

18 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

19 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

Rack Mount Kit Installation

This chapter describes how to use the rack-mount kit to install your Harmony Controller Appliance into an equipment rack. The kit supports front mounting.

• Ear Bracket Installation

Ear Bracket Installation

This section describes how to install the ear brackets used for rack-mount installation.

• Front Mount Installation

Front Mount Installation

This section provides instructions for a front-mount installation.

Align a bracket over the 5 screw holes that will be used to attach the bracket to the chassis. Make sure to use the correct bracket. Each bracket fits on only one of the chassis sides .

FIGURE 11 Alignment of Brackets

20 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

Align the bracket over the screw holes, and fasten the bracket using the provided screws. Make sure the fit is snug.

FIGURE 12 Alignment of Brackets Over Screw Holes

Repeat these steps to attach the other bracket.

Attach the device to the front of the rack. Make sure to fasten the brackets.

FIGURE 13 Attaching Device to Front of Rack

Check all the screws to verify that they are snug.

21 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

FIGURE 14 Verification of Screws

22 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

23 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

Power Supply Product Specifications

The A10 Harmony Controller 2000 devices are compatible with the power supply units described in this chapter:

•

750W AC Power Supply Specifications

750W DC Power Supply Specifications

750W AC Power Supply Specifications

Table 3 lists the specifications for the AC power supply.

TABLE 3 750W - AC Power Supply Product Specification

Item Specification

Part Number

Power Supply Output

AC Input Voltage Range

ASK-PS-040

750W 80 Plus Platinum

90~264 VAC

750W DC Power Supply Specifications

Table 4 lists the specifications for the DC power supply.

TABLE 4 750W - DC Power Supply Product Specification

Item Specification

Part Number

Power Supply Output

DC Input Voltage Range

ASK-PSDC-040

40~72 VDC

750W Operation

24 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

25 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

26 | P a g e A 1 0 H a r m o n y T M C o n t r o l l e r 2 0 0 0 I n s t a l l a t i o n G u i d e

¡Hola! Soy un chatbot de IA específicamente entrenado para ayudarte con el A10 Harmony Controller 2000 Manual de instalación. He revisado a fondo el documento y puedo ayudarte a localizar la información exacta que necesitas o explicar el contenido de forma clara y sencilla. Ya sea que busques orientación sobre funciones específicas, pasos para solucionar problemas o uso general, no dudes en hacer tus preguntas. Cuantos más detalles proporciones sobre tus inquietudes o necesidades, más preciso y eficaz será mi apoyo.