- Computers & electronics
- Audio & home theatre
- Video converters
- A-Neuvideo
- ANI-1201HD
- Instruction manual
A-Neuvideo ANI-1201HD Instruction Manual
Add to my manuals
16 Pages
A-Neuvideo ANI-1201HD is a 12-channel presentation scaler switcher supporting various input types like HDMI, VGA, YPbPr, C-Video, and S-Video. It allows seamless switching and scaling of input signals to HDMI and VGA outputs with resolutions up to 1080p. The device offers advanced features like video gain compensation, adjustable aspect ratios, image zooming, and microphone inputs with level control. With its user-friendly interface and remote control, ANI-1201HD is perfect for multi-source video presentations, conferencing, and home theater setups.
advertisement
ANI-1201HD
12 Input Multi Format Video Switcher With
HDBaseT™, VGA and HDMI Outputs
A-NeuVideo.com
Frisco, Texas 75034
(317) 456-2461 V2.0
AUDIO / VIDEO MANUFACTURER
SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to qualified service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original factory packing.
19. Service Information Equipment should be serviced by qualifier service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL
A NEU VIDEO
TABLE OF CONTENTS
CONTENTS
CONTENTS ...................................................................................1
FEATURES .................................................................................... 2
SPECIFICATION ........................................................................... 3
FRONT & REAL PANEL .................................................................4
VIDEO/AUDIO DESCRIPTION .....................................................5
OSD OPERATION (ON-SCREEN-DISPLAY) ................................ 7
IR REMOTE DESCRIPTION ........................................................8
RS-232 CABLE PINS USED ....................................................9
RS-232 CONTROL COMMAND INTRODUCTION ......................10
TCP/IP CONTROLLING ..............................................................12
FIRMWARE UPDATING / SYSTEM DIAGRAM............................13
Dear Customer
Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this equipment:
• Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit.
PACKAGE CONTENTS
Before attempting to use this unit, please check the packaging and make sure the following items are contained in the shipping carton:
• ANI-1201HD Switch
• IR Remote Control
• IR Extender
• HDBaseT™ Receiver
• Rack Mounts
• RS-232 driver CD (All Windows Operating Systems)
• Users Guide
• AC Power Cord (North America)
DISCLAIMERS
The information in this manual has been carefully checked and is believed to be accurate. We assume no responsibility for any infringements of patents or other rights of third parties which may result from its use.
We assume no responsibility for any inaccuracies that may be contained in this document. We make no commitment to update or to keep current the information contained in this document.
We reserve the right to make improvements to this document and/ or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual, or otherwise — without the express written permission and consent.
© Copyright 2015. All Rights Reserved.
Version 2.0 MAY 2015
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be trademarks of the companies with which they are associated.
1
A NEU VIDEO
FEATURES
FEATURES
ANI-1201HD is a presentation scaler switcher with digital amplifier, it is designed for multi-signal processing, signals of C-Video, S-Video,
YPbPr, VGA and HDMI can be scaled to high-resolution HDMI & VGA format. It supports firmware updating via USB
• 12 channels video inputs: 4x HDMI, 4x VGA, 1x YPbPr (Component Video), 2x C-Video (Composite Video), 1x S-Video. All of these inputs will be scaled/switched to HDBaseT™, HDMI & VGA outputs
• Supports VESA standard, including: 640x480, 800x600, 1024x768, 1280x1024, 1280x768, 1360x768/60Hz & 1920x1080, supporting the DDC2/B plug and play
• Video signal formats include NTSC, PAL, SECAM. It is auto-adjustable
• Video gain-compensation technology, 10Bit processing
• Component (YPbPr) supports interlaced scanning and progressive scanning, from 480i to 1080p with its built in 1080i up-scaling function
• Clear graphical user interface, easy for operation
• Adjustable aspect ratio, zoom in/out the output image, special mode for computer with HDMI
• Brightness, Contrast, Sharpness and Color Temperature can be adjusted
• The HDMI input supports 1920x1080 full-digital signal, supporting Bit Synchronous Digital audio decoding
• VGA input can be adjusted, including phase, clock, H position and V position
• USB port for firmware updates
• (2) MIC inputs with level control, MIC with pre-amplification, line for direct connection. Volume of both MICs can be adjusted at the same time
• Power-fail memory function. When power restored, last know state will restore
• Advanced picture adjust, including DNR, CTI, Flesh Tone and Adaptive Luma Control
• Freeze Picture feature
• HDMI output resolution supports XGA (1024×768), 720p(1280x720), WXGA(1280×800), HD(1360×768), 1080p(1920×1080)
• TCP/IP control
2
A NEU VIDEO
SPECIFICATIONS
SPECIFICATIONS
• Video Input: 4x HDMI, 4x VGA , 1x YPbPr, 2x C-Video, 1x S-Video
• Input Connector:
• HDMI female connector
• VGA (15 pin HD), female connector
• RCA female connector
• 4 pin mini DIN connector
• Video Input Signal: HDMI 1.3, RGBHV, RGBs, RGsB, RsBsGs, NTSC 3.58, NTSC 4.42,PAL, SECAM
• Video Output: 1x HDMI, 1x VGA, 1x HDMI TP
• Output Connector:
• HDMI female connector
• VGA (15 pin HD), female connector
• RJ-45 connector
• Video Output Signal: 1x HDMI 1.3, 1x VGA, 1x HDMI TP
• Resolution Range:
• 1080p: 1920x1080
• HD: 1360x768
• 720p: 1280x720
• WXGA: 1280x800
• XGA: 1024x768
• Bandwidth:
• HDMI: 4.95Gbps (1.65Gbps per color)
• C-Video/S-Video: 150MHz
• YPbPr: 170MHz
• VGA: 375MH
• Maximum Pixel Clock: 145MHz
• Video Impedance: 75Ω
• Gain: 0dB
• Input / Output Level: 0.5V~2.0Vp-p
• HDCP Management: Compliant with High-bandwidth Digital Content Protection (HDCP) with DVI & HDMI 1.3 standards
• Audio Input: 6x Stereo Audio for line audio, 2x MIC audio
• Audio Output : Stereo audio for line audio, 2x 10W@8Ω amplifier
• Audio Input Connector:
• 4x RCA female connector for YPbPr C-Video & S-Video audio
• 4x 3.5mm jack for VGA audio
• HDMI for HDMI embedded audio
• Audio Output Connector: RCA connector, Amplifier connector
• Audio Input Impedance: >10kΩ
• Audio Output Impedance: 50Ω
• Stereo Channel Separation: >80dB @1KHz
• CMRR: >90dB @20Hz to 20K Hz
• Frequency Response: 20Hz~20K Hz
• Control/Remote: IR remote, Buttons & RS-232, TCP/IP
• Pin Configurations: 2 = TX, 3 = RX, 5 = GND
• Temperature: -20°C ~ +70°C
• Humidity: 10% ~ 90%
• Power Supply: 100VAC ~ 240VAC, 50/60Hz
• Power Consumption: 65W
• Case Dimension (WxHxD): 19 x 1.75 x 9.25 in
• Product Weight: 7 lb
As product improvements are continuous, specifications are subject to change without notice.
3
A NEU VIDEO
FRONT PANEL
q e t
FRONT AND REAR PANEL
y u i w r q Power indicator LED. It will display red when the unit is connected to power. w IR receive sensor for IR remote control.
e Input Signal source type LED status.
r Video signal source type selection buttons. VIDEO source type (HDMI, VGA, Component Composite and or S-Video.) t Signal source channel selection buttons.
y Resolution selection buttons. 1024x768, 1280x720p, 1280x800, 1360x768, 1920x1080p.
u MIC volume control buttons. “ MUTE ” for mute MIC volume, “▲” for MIC volume up, “▼” for MIC volume down, loop controlling.
i Line volume control buttons. “ MUTE ” for mute line volume, “▲” for line volume up, “▼” for line volume down, loop controlling.
REAR PANEL
q w t y i a e r u o q (2) RCA connectors for stereo audio output, one VGA output, one HDMI output with audio embedded, one HDBaseT™ for HDMI
extending (works with ANI-402R) included.
w (4) VGA connectors for VGA inputs.
e (4) HDMI connectors for HDMI inputs.
r (4) 3.5mm stereo audio connectors for VGA audio inputs.
t (1) Component video input (Y/Pb/Pr), (2) composite video inputs, (1) S-Video input, and (2) sets stereo analog audio input.
y (1) RS-232 port for series control, (1) USB port for firmware update. u (2) MIC connectors: MIC with pre-amplification, LINE for audio direct input. (1) TCP/IP port for network control.
i Amplifier with 2x 10W@8Ω output.
o Connector for POWER.
a Grounding connection.
4
A NEU VIDEO
Video/Audio Description
Below are the detailed descriptions of inputs and outputs.
Composite Video and S-Video input
Supports PAL/SECAM/NTSC
Changeable aspect ratio. (Full-screen, wide screen, 4:3)
Color RGB adjustable
Component input
INPUT
RESOLUTION
720x480i
720x480p
720x576i
720x576p
1280x720p
1280x720p
1920x1080i
1920x1080i
1920x1080i
1920x1080p
Frame
Frequency
2:1
1:1
2:1
1:1
1:1
1:1
2:1
2:1
2:1
1:1
1920x1080p 1:1
The bandwidth is up to 170MHz.
525
525
625
625
750
750
1125
1125
1250
1250
1250
DISPLAy PARAMETER
Frame
Frequency
15.75
31.5
15.625
31.25
45
37.50
28.125
33.75
31.25
62.5
67.5
Changeable aspect ratio. (Full-screen, wide screen, 4:3, auto-adjust)
Supports HDTV input.
60
60
50
50
60
50
50
60
50
50
50
VGA input
The VGA resolution is VESA standard, supporting:
NO. RESOLUTION
1 720x400@70 Hz
NO. RESOLUTION
8 1024x768@70 Hz
2 640x480@60 Hz
3 640x480@72 Hz
9
10
1024x768@75 Hz
1280x768
4
5
6
800x600@60 Hz
800x600@72 Hz
800x600@75 Hz
7 1024x768@60 Hz
11 1280x1024@75 Hz
12 1360x768@60 Hz
13 1920x1080
Bandwidth up to 375MHz.
Adjustable Audio bass & treble
Changeable aspect ratio. (Full-screen, 4:3)
5
Frame
Frequency
4:3
4:3
4:3
4:3
16:9
16:9
16:9
16:9
16:9
16:9
16:9
A NEU VIDEO
Video/Audio Description
HDMI input
HDMI resolution support:
NO. RESOLUTION
1 640x480@60 Hz
2 640x480@72 Hz
3 640x480@75 Hz
4 800x600@56 Hz
5 800x600@60 Hz
6 800x600@72 Hz
7 800x600@75 Hz
8 1024x768@60 Hz
NO. RESOLUTION
9 1024x768@70 Hz
10 1024x768@75 Hz
11 1280x1024@75 Hz
12 1280x720p
13 1360x768
14 1920x540
15 1920x1080i
16 1920x1080p
Digital embedded audio decoding.
Changeable aspect ratio. (Full-screen, wide screen, 4:3, auto-adjust)
Supports HDCP 1.3, compatible with DVI signal
Audio input/output
• 2x Pairs of Left & Right stereo analog audio input
• 4x VGA audio inputs
• 2x MIC audio inputs
• 2x 10W@8Ω amplifier output
• Left & Right stereo audio output
• HDMI embedded audio.
• Volume/Bass/Treble adjustable
• Audio status presets, changeable scene mode
6
A NEU VIDEO
OSD Operation (On-Screen-Display)
The ANI-1201HD provides a nice OSD operation menu, with various functions and language. The operation introduction is:
Picture Setting
The first icon from left of OSD menu is to set the picture parameters. It includes the pictures mode preset, color temperature, contrast, brightness, hue, saturation, sharpness, scale, VGA setting and Advance picture adjust.
Some parameters are only available on certain inputs. For example: VGA setting can be set only with VGA input.
The Advance Picture Adjust can set the Digital Noise Reduction, dynamic color, skin tone and Adaptive Luma adjustment function on or off. DNR is recommended to be set to ON as it makes the output image clear and smooth.
Figure 1: OSD Display
Audio Setting
The Second icon from left of OSD menu is to set the audio/sound parameters. It includes the sound effect preset, bass, treble, balance, scene mode, surround and smart volume setting. Some parameters are only available depending on the input type.
Figure 2: OSD Sound Effect
System Setting
The Third icon from left of OSD menu is the System Setting. It includes the OSD language setting, audio listen only, and freeze output picture etc.
Figure 3: OSD System Setting
7
A NEU VIDEO
Remote operation
Menu/Volume
MUTE for line and MIC audio mute.
Output Resolution
720p: 1280x720
1080p: 1920x1080
XGA: 1024x768
WXGA: 1280x800
HD: 1360x768
IR Remote Description
Source Select
12 Input Channels:
4x HDMI
4x VGA
2x Composite Video
1x S-Video
1x Component
Line Volume
Active when not in MENU
Direction and OK, these buttons are available only in MENU mode.
MIC Volume
Active when not in MENU
8
A NEU VIDEO
RS-232 Cable Pins Used
1. Transmission Rate: 9600 bps
2. Data Format: 8 data bits, No parity , 1 start bit, and 1 stop bit
3. Flowing Control: None
Also known as 9600,8,n,1
9
A NEU VIDEO
RS-232 Control Command Introduction
Note:
1: The letter inside the bracket [ ] is the variable code, which is changeable.
2: The bracket [ ] is not part of the command.
3: Any dot “.” after the letters is part of the command.
Example 1: Switch the Input 2 to the line out. RS-232 command: [2A1.]
Example 2: Turn up the volume on line audio. RS-232 command: [603%]
Example 3: Preset the MIC volume to “21” degree. RS-232 command: [521%]
Example 4: Check the status of Zoom function [0608%]
To cycle thru the Zoom functions, send the command repeatedly [0608%][0608%]
Communication protocol
COMMAND
(ASCII)
0600%
0611%
0612%
0613%
0614%
0615%
0616%
0617%
0618%
0626%
0627%
0628%
0629%
0630%
0631%
0601%
0602%
0603%
0604%
0605%
01xx%
02xx%
03xx%
04xx%
05xx%
0606%
0607%
0608%
0609%
0610%
FUNCTION DESCRIPTION
MUTE Line
UnMute Line
Audio turn up
Audio turn down
Lock the front panel button
Unlock the front panel button
Preset the volume. The XX is ranging from 00 to 99
Preset the brightness. The XX is ranging from 00 to 99
Preset the contrast. The XX is ranging from 00 to 99
Preset the saturation. The XX is ranging from 00 to 99
Preset the sharpness. The XX is ranging from 00 to 07
Auto-adjust the input parameter(VGA only)
Auto-adjust the color temperature
ZOOM the image, set the aspect ratio
OK, for OSD selection
Left of OSD
Right of OSD
Up of OSD
Down of OSD
Set the picture mode
Sound Mode
MENU of OSD
Command to reset to factory defaults
Change the resolution to 1360x768 HD
Change the resolution to 1024x768 XGA
Change the resolution to 1280x720 720p
Change the resolution to 1280x800 WXGA
Change the resolution to 1920x1080 1080p
Check the volume level
Check the input source
10
FEED BACk
(ExAMPLE) (ASCII)
LINE Mute On
LINE Mute Off
LINE Volume: XX
LINE Volume: XX
Panel Locked
Panel UnLocked
Volume: XX
Brightness: XX
Contrast: XX
Saturation: XX
Sharpness: XX
Adjustment
Color Temp: XX
Aspect Ratio: XX
OK
Left
Right
Up
Down
Picture Mode : XX
Sound Mode: XX
MENU
Factory reset
Resolution: HD 1360x768
Resolution: XGA 1024x768
Resolution: 720p 1280x720
Resolution: WXGA 1280x800
Resolution: 1080p 1920x1080
LINE Volume: XX/MIC Volume: XX
Source: XXXXXX
A NEU VIDEO
RS-232 Control Command Introduction
COMMAND
(ASCII)
0632%
0704%
0705%
0706%
0707%
0708%
0709%
0710%
0711%
0652%
0655%
0656%
0698%
0699%
0701%
0702%
0703%
0712%
0720%
0721%
0722%
0723%
0724%
0725%
08xx%
0633%
0634%
0635%
0636%
0637%
0638%
0639%
0640%
0644%
0646%
0647%
0648%
0649%
0650%
0651%
FUNCTION DESCRIPTION
Check the output resolution
Check the image mode
Check the audio mode
Check the image aspec ratio
Check the brightness
Check the contrast
Check the saturation
Check the sharpness
Check the color temperature
OSD CHANNEL display enabled
Volume Bar display enabled
Volume Bar display disabled
Digital audio (HDMI and SPDIF) output enabled
Shield digital audio (HDMI and SPDIF) output
Check OSD CHANNEL display status
Check Volume Bar display status
Check Digital audio output status
Freeze output image
Cancel the freezing of output image
Firmware update
Check Current Firmware Version
Switching to HDMI1 input
Switching to HDMI2 input
Switching to HDMI3 input
Switching to HDMI4 input
Switching to VGA1 input
Switching to VGA2 input
Switching to VGA3 input
Switching to VGA4 input
Switching to composite video AV1 input
Switching to YPbPr input
Switching to S-Video input
Switching to composite video AV2 input
Mute Line and MIC
UnMute Line and MIC
MUTE MIC
UnMute MIC
MIC volume turn up
MIC volume turn down
Preset MIC volume. The XX is ranging from 00 to 99
11
FEED BACk
(ExAMPLE) (ASCII)
Resolution: XXXXXXXX
Picture Mode : XX
Sound Mode: XX
Aspect Ratio: XX
Brightness: XX
Contrast: XX
Saturation: XX
Sharpness: XX
Color Temp: XX
OSD Source: Display
Volume Bar: Display
Volume Bar: No Display
Digital Sound Ouput: Enabled
Digital Sound Ouput: Disable
OSD Source: Display
Volume Bar: Display
Digital Sound Ouput: Enabled
Freeze: Enabled
Freeze: Disable
Source: HDMI 1
Source: HDMI 2
Source: HDMI 3
Source: HDMI 4
Source: VGA1
Source: VGA2
Source: VGA3
Source: VGA4
Source: CVIDEO1
Source: YPbPr
Source: SVIDEO
Source: CVIDEO2
LINE Mute On/MIC Mute On
LINE Mute Off/MIC Mute Off
MIC Mute On
MIC Mute Off
MIC Volume: XX
MIC Volume: XX
MIC Volume: XX
A NEU VIDEO
TCP/IP Controlling
The TP port of ANI-1201HD is used for TCP/IP control. Below is the introduction of TCP/IP control. The ANI-1201HD does not have a build-in webserver for control. The TCP/IP connection requires you either send comments manually or from a third-party controller.
IP Configuration
1. Connect a computer to the TP port, set its IP to the same IP section as the default IP of
ANI-1201HD (192.168.0.178).
Same IP section but cannot be 192.168.0.178
Figure 4: TCP/IP Setup
2. Enter 192.168.0.178 in your web browser, you should see the LOGIN page.
Figure 5: TCP/IP Login Screen
3. Enter the password “88888”, you will be presented with “IPort Configuration Web Server” page. From this page, you can manage system settings like IP address, IP reset, PW reset etc. See Figure 6: TCP/IP IPort Configuration Web Server
Note: Serial configuration is fixed and cannot be changed.
Figure 6: TCP/IP IPort Configuration Web Server
After configuration, reset the device, then you can use the new IP address for controlling.
a. Connection and Command Control
1. Connect a computer and ANI-1201HD to the same network. Open the NET software
(or any other TCP/IP communication software) and create a connection, enter the IP address and port of ANI-1201HD (default IP: 192.168.0.178, port:4001):
Figure 7: Connection and Command Control
2. After successful connection; you can enter commands to control the ANI-1201HD.
Figure 8: commands to control via TCP/IP
12
A NEU VIDEO
Firmware Updating / System Diagram
Firmware Updating
The ANI-1201HD supports firmware field-updating by USB flash disk.
Note: ANI-1201HDUpdateFile.bin” file is provided by A-NeuVideo engineering department and is not available as a public download.
The procedure is as follows:
1. Copy the file “ANI-1201HDUpdateFile.bin” to a USB flash disk.
2. Plug the USB flash disk into the USB port on the ANI-1201HD.
3. Pressing the button “HDMI” on the front panel for 6 seconds or sending RS-232 command 0698% for updating, then press the button “Ok” on the remote or send RS-232 command 0609% to confirm update. The ANI-1201HD will capture the new firmware from USB flash disk.
4. After updating finish, reboot and send the command “0617%” to reset to factory settings.
5. After reset, reboot again.
System Diagram
13
A NEU VIDEO
TERMS AND CONDITIONS OF USE
PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED
BY, THROUGH OR UNDER A-NeuVideo, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to A-NeuVideo, Inc. at the return address set forth on the Product’s packing label at your expense. A-NeuVideo, Inc. may modify these Terms and Conditions at anytime, without notice to you.
RESTRICTIONS ON USE OF THE PRODUCT
It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product.
You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be borne by you and you agree to indemnify and hold harmless A-NeuVideo, Inc. from and against any such damage.
The Product is protected by certain intellectual property rights owned by or licensed to A-NeuVideo. Any intellectual property rights pertaining to the Product are licensed to you by A-NeuVideo, Inc. and/or its affiliates, including any manufacturers or distributors of the Product (collectively, “A-NeuVideo”) for your personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.
The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by A-NeuVideo for your personal use only.
A-NeuVideo does not transfer either the title or the intellectual property rights to the Product and A-NeuVideo retains full and complete title to the intellectual property rights therein. All trademarks and logos are owned by A-NeuVideo or its licensors and providers of the Product, and you may not copy or use them in any manner without the prior written consent of A-NeuVideo, which consent may be withheld at the sole discretion of A-NeuVideo.
The functionality and usability of the Product is controlled by A-NeuVideo, Inc. from its offices within the State of Texas, United States of America. A-NeuVideo makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided with respect thereto. You are advised that the Product may be subject to U.S. export controls.
Disclaimers and Limitation of Liability
A-NeuVideo may change or modify the Product at any time, from time to time.
THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. A-NEUVIDEO DOES NOT WARRANT OR
MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY,
OR OTHERWISE.
A-NeuVideo has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should not be relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the Product.
TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, A-NEUVIDEO DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
A-NEUVIDEO DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT.
A-NEUVIDEO DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO
THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS.
A-NEUVIDEO WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU NOT
TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT A-NEUVIDEO) ASSUME THE ENTIRE COST OF ALL
NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING BY
A-NEUVIDEO.
UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL A-NEUVIDEO BE LIABLE FOR ANY SPECIAL OR CONSEQUENTIAL
DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS, EVEN IF
A-NEUVIDEO OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL A-NEUVIDEO’S TOTAL
LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE) EXCEED THE AMOUNT YOU
PAID TO A-NEUVIDEO, IF ANY, FOR THE PRODUCT.
END OF DOCUMENT
14
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- 12-channel video input support (HDMI, VGA, YPbPr, C-Video, S-Video)
- HDMI and VGA outputs with resolutions up to 1080p
- Video gain compensation and adjustable aspect ratios
- Image zooming and freeze picture feature
- Microphone inputs with level control
- User-friendly interface and remote control