Lowrance Elite-5x & Elite-7x Operation Manual

PDF

Document

Elite-5x & Elite-7x

manual Operation manual

Lowrance® and Navico® are registered trademarks of Navico.

Navico may find it necessary to change or end our policies, regulations and special offers at any time.

We reserve the right to do so without notice. All features and specifications subject to change without notice.

Compliance Statements

Lowrance Elite-5x and Elite-7x

• meets the technical standards in accordance with Part 15.103 of the FCC rules

• complies with CE under RTTE directive 1999/5/EC

• complies with the requirements of level 2 devices of the Radiocommunications (Electromagnetic

Compatibility) standard 2008

For more information please refer to our website: www.lowrance.com.

Warning

The user is cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that of the receiver

• Consult the dealer or an experienced technician for help

Table of Contents | Elite-5x & Elite-7x PB

Introduction ...................................... 3

Unit Controls ............................................3

Conventional sonar and Downscan .........3

Basic Operation ............................... 4

Setup wizard ............................................4

Pages ......................................................4

Selecting Pages.......................................4

Page menus ............................................4

Fishing Modes .........................................7

Cursor ......................................................8

Advanced Mode ......................................8

Restore defaults ......................................9

Pages .............................................. 10

Sonar Page............................................10

Downscan page ....................................10

Combo pages ........................................ 11

Overlay Data..........................................12

Sonar Operation ............................ 14

Trackback ..............................................14

CHIRP ...................................................14

Sensitivity ..............................................16

Colorline ................................................16

Range ....................................................16

Frequency .............................................17

Ping Speed ............................................18

1 Table of Contents | Elite-5x & Elite-7x

Fish ID ..................................................19

Downscan options .................................20

Sonar Settings .......................................21

Installation .............................................22

DSI Operation ................................. 24

Trackback .............................................24

DSI menu...............................................24

Ping Speed ............................................26

Downscan options .................................26

Settings .......................................... 29

Settings menu........................................29

System...................................................29

Set Language ........................................30

Audio .....................................................30

Alarms ..................................................30

Units ......................................................31

NMEA 0183 ...........................................31

NMEA 2000 ...........................................31

Specifications ................................ 33

Index ............................................... 34

Table of Contents | Elite-5x & Elite-7x 2 PB Table of Contents | Elite-5x & Elite-7x

Introduction | Elite-5x & Elite-7x PB

Unit Controls

LiGhT/Power: controls backlight level and turns unit on/off

KeYPAD: controls cursor & selects items on menus

PAGeS view

: allows you to select a page to

MenU: opens settings, context and page menus

enTer: finalizes menu selections

ZooM Keys: used to zoom in/zoom out

Turn unit on/off

Getting Started

To turn on/off the unit, press and hold the LiGhT/Power key for three seconds.

Adjusting the backlight

This unit has 10 backlight levels.

Press the LiGhT/Power key to switch backlight levels.

Muting

Audio

Select Mute Audio from the

System menu and press enTer.

Conventional sonar and Downscan

This unit supports two types of sonar: Conventional and Downscan.

Refer to the Sonar Operation section for information about conventional sonar features and settings.

Downscan features and settings are covered in the

Downscan Operation section.

3 Introduction | Elite-5x & Elite-7x

Basic Operation

Setup wizard

The Setup wizard will appear when the unit is turned on for the first time. To choose your own settings, do not run the setup wizard. To restart the

Setup wizard, restore defaults.

Selecting Pages

To select a page, press the keypad in the direction of the desired page and press EntEr.

Pages

This unit has three pages: Downscan, Sonar and

Sonar/Downscan.

Page menus

The Downscan and Sonar pages have menus that can only be accessed when those pages are displayed.

Pages dialog

Basic Operation | Elite-5x & Elite-7x 4

Downscan page

Downscan menu

5 Basic Operation | Elite-5x & Elite-7x

Basic Operation | Elite-5x & Elite-7x 4

accessing the Settings menu

Sonar page

Sonar menu

Combo pages

Two-panel page

Horizontal panel

Press the PagES key twice to switch active panels.

The page menu for active page will be displayed when the MEnu key is pressed.

accessing menu items

The keypad and EntEr key are used to select menu items and open submenus. Use the keypad to highlight the desired item and press EntEr.

5 Basic Operation | Elite-5x & Elite-7x

Working with menus

There are several menu types used to make adjustments to options and settings, including scrollbars, on/off features and dropdown menus.

Scrollbars

Select the scrollbar and press the keypad left (decrease) or right

(increase).

nOtE: Press the MEnu key to Exit menus.

Dialogs

Dialogs are used for user input or for presenting information to the user. Depending on the type of entry, different methods are used to confirm, cancel or close the dialog.

On/Off features

Select an on/off menu item and press EntEr to turn it on/off.

Entering text

Some functions, like naming a waypoint, route or trail, will require you to input text.

Dropdown menus

Access the dropdown menu and press use the keypad to select the desired item and press EntEr.

Basic Operation | Elite-5x & Elite-7x 6 7 Basic Operation | Elite-5x & Elite-7x

Basic Operation | Elite-5x & Elite-7x 6

To input text:

1. Use the keypad to select the desired character and press EntEr.

2. Repeat Step 1 for each character.

3. When entry is completed, highlight OK and press EntEr.

Fishing Modes

(Conventional sonar only)

Fishing modes enhance the performance of your unit by providing preset packages of sonar settings geared to specific fishing conditions.

Switches letters to uppercase/ lowercase

Switches keyboard between Alpha and

QWERTY layout

7 Basic Operation | Elite-5x & Elite-7x

General Use

Shallow

Water

Fresh Water

Deep Water

Slow

Trolling

Fast

Trolling

Clear Water

Brackish

Water

Ice

Fishing Mode Options

1000ft or less Coastal

60ft or less

400ft or less

1000ft or more

400ft or less

Shallow weedy bottoms

Inland/Near coastal

Offshore

Inland/Coastal

Fresh-Saltwater mix

Ice fishing

Cursor

The keypad moves the cursor around the display, allowing you to scroll the map, select map items and review sonar history.

Press MEnu and select Return to vessel or Exit cur-

sor mode to clear the cursor.

advanced Mode

Enables advanced features and settings.

The following features are enabled when Advanced mode is turned on:

• Units (Enables distance, speed, depth, temperature, and bearings options)

• NMEA 0183 Output

NOTE: Use Fresh Water mode when fishing in less than 100 feet of water; otherwise your unit may not track bottom properly.

Basic Operation | Elite-5x & Elite-7x 8 9 Basic Operation | Elite-5x & Elite-7x

Basic Operation | Elite-5x & Elite-7x 8

Standby mode

Lowers power consumption by turning off sonar and the display.

Press the PWr/Light key to access the Backlight dialog.

Select Standby and press EntEr.

Press any key to resume normal operation.

restore defaults

Resets unit options and settings to defaults.

nOtE: Leaving your unit in Standby mode when your boat is not is use will run down your battery.

9 Basic Operation | Elite-5x & Elite-7x

Sonar Operation

Blue sonar history bar

This unit supports two types of sonar: Conventional and Downscan.

Trackback

You can review your recent sonar history by moving the cursor to the left until the screen starts to move in reverse.

Move the sonar history bar all the way to the right to resume normal sonar scrolling, or press Menu and select Exit cursor mode.

The features described in this section are for conventional sonar. Refer to the Dowscan operation section for information on Dowscan features.

CHIRP

A CHIRP (Compressed High Intensity Radar Pulse) transducer transmits a modulated pulse of all frequencies within the bandwidth of the selected transducer type.

Sonar Operation | Elite-5x & Elite-7x 14 15 Sonar Operation | Elite-5x & Elite-7x

Sonar Operation | Elite-5x & Elite-7x 14

This results in better image quality, better target separation and greater depth penetration.

This unit supports High CHIRP and Medium CHIRP frequencies. You can use CHIRP with Lowrance conventional sonar transducers.

• 50/200 kHz (Low/High CHIRP)

• 83/200 kHz (Medium/High CHIRP)

CHIRP Setup

1. Select a CHIRP transducer type from the Transducer type menu

2. Select the desired CHIRP frequency from the Frequency menu

Sonar Menu

Press Menu from any sonar page to access the Sonar menu.

(Options active with Downscan overlay turned on)

Adjust

Used to make adjustments to Sensitivity and Colorline/Grayscale.

15 Sonar Operation | Elite-5x & Elite-7x

Sensitivity

Controls the level of detail shown on the display.

Too much detail will clutter the screen. If Sensitivity is set too low, desired echoes may not be displayed.

NOTE: You can make minor (+/-4%) changes to sensitivity with Auto Sensitivity turned on. You will have to turn it off to make significant adjustments.

Colorline

Separates strong sonar echoes from weak sonar echoes. That makes it easier for you to distinguish fish or structure from the bottom. A hard return will be shown as a wide, bright yellow area, whereas a soft return will be a narrow reddishblue area.

Range

Selects the deepest range shown on the display. Range settings display the section of the water column from the water surface to the selected depth range.

If you select too shallow a depth range, the unit will not be able to lock onto the bottom.

Auto Sensitivity

Keeps sensitivity at a level that works well under most conditions, reducing the needs for adjustments. Auto Sensitivity is turned on by default.

Custom Range — Upper and Lower Limits

Used to select the upper limit and lower limit of a section of the water column. That allows you to view a section of the water column that does not include the water surface. Upper and lower limits must be at least 6.5 ft (2m) apart.

Sonar Operation | Elite-5x & Elite-7x 16 17 Sonar Operation | Elite-5x & Elite-7x

Sonar Operation | Elite-5x & Elite-7x 16

Custom range menu

nOTe: When using a custom range, you may not receive any digital depth readings, or you may receive incorrect depth information.

Frequency

Controls the transducer frequency used by the unit.

This unit supports the following frequencies: 50 kHz, 83 kHz, 200 kHz, Low CHIRP, Medium CHIRP and High CHIRP.

Only frequencies supported by your transducer will be shown on the Frequency menu.

50 kHz

83 kHz

200 kHz

Low CHIRP

High CHIRP

Sonar Frequencies

Best depth penetration with lower resolution

Medium CHIRP

Wider cone angle provides more bottom coverage

Highest sensitivity and best target separation in shallow water

Provides the best depth penetration with lower resolution

Better depth penetration than High CHIRP with minimal loss of target separation

Better resolution in shallow water than Medium CHIRP

17 Sonar Operation | Elite-5x & Elite-7x

Ping Speed

Controls the rate the transducer uses to send sonar waves into the water. Ping speed adjustments can help reduce interference from other transducers.

When using fishing modes, ping speed settings are optimized for the selected fishing conditions, so in most cases, adjustments are not necessary.

Sonar Options

Sonar Operation | Elite-5x & Elite-7x 18

Noise Rejection

Uses advanced signal processing to monitor the effects noise (boat pumps, water conditions, engine ignition systems, etc.) has on your display, and then filters out undesired signals.

19 Sonar Operation | Elite-5x & Elite-7x

Sonar Operation | Elite-5x & Elite-7x 18

Surface Clarity

Surface Clarity reduces surface clutter by decreasing the sensitivity of the receiver near the surface.

Surface Clutter

Color

Allows you to change the look of the display using palettes with varying degrees of color/brightness.

Amplitude Scope

Displays the amplitude of the most recent echo.

Amplitude scope

Split Zoom and Split Flasher

Switches the sonar display from full screen sonar to a split screen view.

Split Zoom Split Flasher

Fish ID

Displays fish echoes as fish symbols instead of fish arches.

Fish ID is not the most accurate method of fish detection since structure and suspended debris may be shown as a fish symbol on the display.

19 Sonar Operation | Elite-5x & Elite-7x

Downscan options

You can make adjustments to Downscan overlay settings from the sonar page. Downscan options are covered in more detail in the DSI section.

Stop Sonar

Pauses the unit’s sonar, allowing you to get a closer look at suspended targets.

Stop Sonar also can be used to prevent/stop interference between two sonar units running on the boat at the same time.

nOTe: Sonar history will not be

recorded when sonar is stopped.

Downscan options menu

nOTe: The Downscan options menu will only be available when Downscan overlay is enabled.

Overlay Data

Allows you to select data to be displayed on top of the

Sonar page.

Overlay data setup is covered in the Pages section. Overlay data

Sonar Operation | Elite-5x & Elite-7x 20 21 Sonar Operation | Elite-5x & Elite-7x

Sonar Operation | Elite-5x & Elite-7x 20

Sonar Settings

Restricts unit’s digital depth search capability

Turns on/off

Dowsncan overlay display

Sonar Settings Menu

Conventional settings/Downscan Settings

You can adjust settings for both Conventional sonar and Downscan sonar modes from the Sonar

Settings menu.

Only adjustments made to conventional sonar settings will be visible on the sonar page.

Manual Mode

Restricts digital depth capability, so the unit will only send sonar signals to the selected depth range. That allows the display to continue smooth scrolling if the bottom depth is out of transducer range.

WARnInG: Manual mode should only be used by advanced sonar users.

21 Sonar Operation | Elite-5x & Elite-7x

When the unit is in manual mode, you may not receive any depth readings, or you may receive incorrect depth information.

Installation

Fishing Mode

Enhances the performance of your unit by providing preset packages of sonar settings geared to specific fishing conditions. For more information about fishing modes, refer to the Basic

Operation section.

Reset Fishing Mode

Resets selected fishing mode to default settings.

That is useful when you want to clear settings adjustments made while using a fishing mode.

Installation menu

Keel Offset

All transducers measure water depth from the transducer to the bottom. As a result, water depth readings do not account for the distance from the transducer to the keel or from the transducer to the water surface. Before setting keel offset, measure

Sonar Operation | Elite-5x & Elite-7x 22

Transducer

Keel Offset (-3.5 feet)

Keel

23 Sonar Operation | Elite-5x & Elite-7x

Sonar Operation | Elite-5x & Elite-7x 22 the distance from the transducer to the lowest part of the keel. If, for example, the keel is 3.5 feet below the transducer, it will be input as –3.5 feet.

Reset water distance

Reset Water Distance to zero.

Water speed calibration

Calibrates a paddlewheel speed sensor with speed data from a GPS source.

Transducer Type

Selects the type of transducer model attached to your unit.

Temperature calibration

Calibrates data from the transducer temperature sensor with data from a known temperature source to ensure the accuracy of temperature information.

23 Sonar Operation | Elite-5x & Elite-7x

DSI Operation

Move the sonar history bar all the way to the right to resume normal sonar scrolling, or press Menu and select Exit cursor mode.

This unit supports two types of sonar: Conventional and Downscan.

The features described in this section are for

Dowscan sonar. Refer to the Sonar operation section for information on conventional sonar features.

DSI menu

Press Menu from the DSI page to view the DSI menu.

Trackback

You can review your sonar history by pressing the keypad to the left until the screen starts to move in reverse and the sonar history bar appears at the bottom of the screen.

DSI history bar

DSI Operation | Elite-5x & Elite-7x 24

Stops sonar transmission; pauses sonar scroll

25 DSI Operation | Elite-5x & Elite-7x

DSI Operation | Elite-5x & Elite-7x 24

Adjust

Accesses the Contrast adjustment scrollbar, allowing you to adjust contrast settings.

Range

Range settings display the section of the water column from the water surface to the selected depth range.

Contrast

Adjusts the brightness ratio between light and dark areas on the screen, making it easier to distinguish suspended objects from the background.

Custom Range — Upper and Lower Limits

Used to select the upper limit and lower limit of a section of the water column. That allows you to view a section of the water column that does not include the water surface.

Contrast set to 40

Contrast set to 60

Contrast set to 80

DSI units do not have a Sensitivity setting like traditional sonar units. Contrast functions as the sensitivity setting for DSI units.

Upper and lower limits must be at least 6.5 ft (2m) apart.

25 DSI Operation | Elite-5x & Elite-7x

nOTe: When using a custom range, you may not receive any digital depth readings, or you may receive incorrect depth information.

Downscan options

Frequency

Controls the transducer frequency used by the unit. 800 kHz offers the best resolution, while 455 kHz has greater depth coverage.

Downscan options

Ping Speed

Controls the rate the transducer uses to send sonar waves into the water. Ping speed adjustments can help reduce interference from other transducers.

Noise Rejection

Uses advanced signal processing to monitor the effects noise (boat pumps, water conditions, engine ignition systems, etc.) has on your display, and then filters out undesired signals.

DSI Operation | Elite-5x & Elite-7x 26 27 DSI Operation | Elite-5x & Elite-7x

DSI Operation | Elite-5x & Elite-7x 26

Surface Clarity Color

Surface Clarity reduces surface clutter by decreasing the sensitivity of the receiver near the surface.

Allows you to select a color palette best suited to your fishing conditions.

The white background palette works well for suspended targets. Purple is useful for viewing structure detail and determining bottom hardness.

Sepia is best for looking at bottom detail.

Surface Clarity set to Low.

Surface Clarity set to High.

Split Zoom

Changes the display to a split zoom view.

Stop Sonar

Stops sonar transmission and pauses the sonar chart, allowing you to get a better look at suspended targets and structure.

nOTe: Sonar history (Trackback) will

not be recorded when sonar is stopped.

27 DSI Operation | Elite-5x & Elite-7x

Overlay Data

Allows you to select data to be displayed on top of the

DSI page.

Overlay data setup is covered in the Pages section.

Overlay data

Settings

Accesses the Settings menu. Refer to “Sonar Settings” on page 21.

DSI Operation | Elite-5x & Elite-7x 28 PB DSI Operation | Elite-5x & Elite-7x

Settings | Elite-5x & Elite-7x PB

Settings

Settings menu

Accesses installation and configuration settings for your unit.

System

Adjusts unit settings like language, mute audio and advanced mode.

(Advanced mode only)

Settings menu

(Elite-7 units only)

Enables advanced features and settings

System menu

Displays software information

Restores settings and options to factory default settings

29 Settings | Elite-5x & Elite-7x

Set Language

Selects the language used on menus and text boxes.

Audio

Adjusts volume and turns on/off unit audio, like key beeps, alarm sounds, etc.

check the version of software your unit is using by accessing the About screen.

Lowrance periodically updates unit software to add features and improve functionality. To see the latest available software version go to www.

lowrance.com.

Alarms

Enables alarms and selects alarm thresholds.

Advanced Mode

Enables features and settings only available with unit in Advanced Mode.

Sounds alarm when

Fish ID symbol appears on display

Restore Defaults

Switches the unit back to default settings. Alarms menu

About

Displays software information about this unit.

Before attempting a software update, you can

Settings | Elite-5x & Elite-7x 30 31 Settings | Elite-5x & Elite-7x

Settings | Elite-5x & Elite-7x 30

Shallow

Fish

Alarms sounds alarm when vessel enters water shallower than the selected shallow threshold sounds alarm when a fish symbol (Fish ID) appears on the sonar screen

NMEA 0183

You can select the NMEA 0183 sentences the unit will use when connected to a VHF radio or other

NMEA 0183 device.

Units

Allows you to select the unit of measure used by the unit. Unit options vary depending on whether the unit is in basic or advanced mode.

You can also adjust the Baud rate, but the default setting works best under most conditions.

Basic Mode Advanced Mode

NMEA 2000 (Elite-7 units only)

With the unit connected to a NMEA 2000 network, you can select a GPS antenna on the network as your GPS source, and share newly created waypoints with other display units on the network.

31 Settings | Elite-5x & Elite-7x

You will not be able to share existing waypoints.

Only waypoints created while the unit is connected to a NMEA 2000 network can be shared, and only with units on that network.

Simulator

Simulates GPS and/or sonar activity. Simulations can be customized on the Simulator options menu.

Selecting a GPS source

Data sources (Elite-7 units only)

Allows you to select the source this unit will use for

GPS data.

Device list (Elite-7 units only)

Used to view data for devices connected to your

NMEA 2000 network.

Settings | Elite-5x & Elite-7x 32 PB Settings | Elite-5x & Elite-7x

Specifications | Elite-5x & Elite-7x PB

Case Size

Display

Waterproof standard

Backlight

Communications

Declaration of

Conformity

Elite -5x & Elite-7x

General

Elite 7x: 5.3” H (234mm) x 9.2” W

(136mm); 5.9” H (151mm) with bracket

Elite-5x: 5.4” H (136 mm) x 6.9” W (174 mm); 5.9” H (151 mm) with bracket

Elite-7x: (7” diagonal) 16-bit color Full

VGA Solar MAX™ 800x480 color TFT

Elite-5x: (5” diagonal) 16-bit color Full color VGA Solar MAX™ Plus TFT

IPX7

LED (11 levels)

Elite 7x: NMEA 2000, NMEA 0183

Output

Elite 5x: NMEA 0183 Ouput

Part 15.103 FCC rules & CE RTTE directive 1999/5/EC

Transmit Power

Power

Requirement

Voltage Input

Current drain

Fuse type

12V

Power

250W RMS; 30,000 PTP

10 to 17V

Typical: 1.1A

Max depth

Transducer

Frequency

3-amp Automotive

Sonar

300ft (91m) 455/800Khz

1000ft (305m) 83/200kHz

2500ft (762m) 50/200kHz

455/800kHz

50/83/200kHz

High/Medium/Low CHIRP

70mph Max speed

Transducer

HDI 50/200kHz (Low/High CHIRP)

HDI 83/200kHz (Medium/High CHIRP

83/200kHz (Medium/High CHIRP)

Transducer cable 20ft (6m)

33 Specifications | Elite-5x & Elite-7x

Index

A

About 30

Adjust menu 15

Advanced Mode 8

Alarms 30

Amplitude Scope 19

Auto Sensitivity 16

C

CHIRP 14

Color 19, 27

Colorline 16

Contrast 25

Cursor 8

Custom Range 16, 25

D

Depth Range 25

Index | Elite-5x & Elite-7x

Dialogs 6

Dropdown menus 6

DSI menu 24

F

Fish alarm 31

Fish ID 19

Fishing Mode 7

Fishing Modes

Reset 22

Frequency 17, 26

H

High CHIRP 17

I

Ice Mode 20

Installation menu 22

K

Keel Offset 22

L

Language 30

Low CHIRP 17

M

Manual Mode 21

Medium CHIRP 17

Mute Audio 30

N

NMEA 0183 31

NMEA 2000 31

Data sources 32

Noise Rejection 18, 26

O

On/Off features 6

Overlay Data 12, 28

Configure 12

Customizing 13

Show 12

P

Page menus 4

Page selection 4

Ping Speed 17

R

Range 25

Reset Fishing Mode 22

Reset water distance 23

35 Index | Elite-5x & Elite-7x

Index | Elite-5x & Elite-7x 34

S

Saving Screenshots 30

Scrollbars 6

Sensitivity 16

Setup wizard 4

Shallow alarm 31

Software Updates 30

Sonar Installation 22

Sonar Menu 15

Sonar Options menu

Sonar Page 10

Sonar settings 21

Split Flasher 19

Split Zoom 18

Standby mode 9

Stop Sonar 20, 27

Surface Clarity , 19

System settings 29

T

Temp calibration 23

Text entry 6

Trackback 24

Turn unit on/off 3

U

Unit Controls 3

Units 31

Upper & Lower Limits

16, 25

W

Working with menus 6

35 Index | Elite-5x & Elite-7x

Contact information

Customer Service:

1-800-628-4487

(8 a.m. to 5 p.m. Central Standard Time, M-F)

(Canada)

1-855-361-1564 [email protected]

(8 a.m. to 5 p.m. Eastern Standard Time, M-F)

Ordering Accessories

http://store.navico.com/

Visit our website

www.lowrance.com

Visit our website:

www.lowrance.com

*988-10652-001*

Hello! I am an AI chatbot specifically trained to assist you with the Lowrance Elite-5x & Elite-7x Operation manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant is out of keyboard. Please, try again later.

manual Operation manual

Compliance Statements

Warning

Table of contents

Introduction ...................................... 3

Basic Operation ............................... 4

Pages .............................................. 10

Sonar Operation ............................ 14

DSI Operation ................................. 24

Settings .......................................... 29

Specifications ................................ 33

Index ............................................... 34

Unit Controls

Getting Started

Conventional sonar and Downscan

Basic Operation

Setup wizard

Selecting Pages

Pages

Page menus

accessing the Settings menu

accessing menu items

Working with menus

Dialogs

Entering text

Fishing Modes

Cursor

advanced Mode

Standby mode

restore defaults

Pages

Sonar Page

Downscan page

Combo pages

Overlay Data

Sonar Operation

Trackback

CHIRP

Sonar Menu

Sonar Options

Downscan options

Sonar Settings

Installation

DSI Operation

DSI menu

Trackback

Downscan options

Settings

Settings menu

System

Alarms

Index

A

C

D

F

H

I

K

L

M

N

O

P

R

S

T

U

W

Contact information

1-800-628-4487

1-855-361-1564 [email protected]

Ordering Accessories

Visit our website

Visit our website:

www.lowrance.com

Related

Lowrance Elite-7x Operation Manual

Lowrance Elite X Series Operator Manual - Read Online

Lowrance Elite 5x, Mark 5x, Mark 5x Pro, & Elite 4x Installation & Operation Manual