advertisement
Parts Manual
PL31-15LN250
12/27/2013
15LN250-62
Right Angle Drill
For additional product information visit our website at http://www.apextoolgroup.com
October 31, 1994
DOTCO
Ò
15LN250--62
01--2505
Inlet Adapter
(1/4” NPT)
01--2506
Exhaust Plug
2965 O--Ring
3036 O--Ring
1042
Pin
01--2519
Valve
Spring 01--2518
Valve
01--2504
Valve Seat
Motor Housing Assembly
01--1020 Lever
01--2517 Push Rod
01--2584 Motor Housing
· 4293
Filter Disc
·
part. Order one (1) or one set for every 6--10 tools. Small, easily lost or low cost parts should also be ordered on the basis of 3--4 per 10 tools.
01--2581
Filter Retainer
· 01--2061
Muffler
01--2596
Muffler Housing
14--0851
12 pt. Housing
Wrench
01--1169
O--Ring
Page 2
October 31, 1994
90 ° Compact Angle Head
Part #1025409
1006205 Retaining Nut
· 1009087 Ball Bearing
1009643 Spindle Extension
1”--20
LH Thread
· 1019559 Ball Bearing
= · 1019555 Bevel Gear
1008748 Shim — 0.002”
1013224 Shim — 0.005”
As
Required
1019556 Angle Head
(Includes #1008992 Grease Fitting)
1”--20
LH Thread
As Required
1006265 Shim (0.002”)
1006266 Shim (0.003”)
1006267 Shim (0.005”)
( = ) NOTE: ALWAYS replace Bevel
Gear and Output Spindle IN PAIRS since both should wear equally.
· 1019559 Ball Bearing
1019759 Spanner Wrench (service wrench not supplied with angle head assembly).
Fits #1019569 Bearing Cap
3/8” Hex
LUBRICATION
Only Molykote is recommended for use in this angle head.
Wipe on only a small amount and remove any excess.
REASSEMBLY (With new components)
1. Start with only one 0.002” shim (part #1006265) above work spindle in bearing pocket. Assemble all output spindle components, applying Molykote, and tighten bearing cap to 15 inch--pounds torque.
This is for end play only. With too much play, take out the
0.003” shim. A slight back--and--forth amount of play is acceptable and necessary.
2. Assemble all remaining components and check gear
“shake”. This is for gear mesh which should be no more than
0.005”.
3. Be sure to apply Molykote before assembly.
· 1019560 Ball Bearing
·
=
· 1019551
Output Spindle
(1/4”--28 Internal Thread)
1019569 Bearing Cap
(LH Thread)
Tighten to 15
Inch Pounds torque.
or one set for every five (5) tools, or two sets for 6--10 tools. Small, easily lost or low cost parts should also be ordered on the basis of 3--4 per 10 tools.
Page 4
Detroit, Michigan
Apex Tool Group
Sales & Service Center
2630 Superior Court
Auburn Hills, MI 48326
Tel: (248) 393-5640
Fax: (248) 391-6295
Houston, Texas
Apex Tool Group
Sales & Service Center
6550 West Sam Houston
Parkway North, Suite 200
Houston, TX 77041
Tel: (713) 849-2364
Fax: (713) 849-2047
Lexington, South Carolina
Apex Tool Group
670 Industrial Drive
Lexington, SC 29072
Tel: (800) 845-5629
Tel: (803) 951-7544
Fax: (803) 358-7681
Los Angeles, California
Apex Tool Group
Sales & Service Center
6881 Stanton Avenue
Unit B
Buena Park, CA 90621
Tel: (714) 994-1491
Fax: (714) 994-9576
Seattle, Washington
Apex Tool Group
Sales & Service Center
2865 152nd Avenue N.E
Redmond, WA 98052
Tel: (425) 497-0476
Fax: (425) 497-0496
Sales & Service Centers
Note: All locations may not service all products. Please contact the nearest Sales & Service Center for the appropriate facility to handle your service requirements.
York, Pennsylvania
Apex Tool Group
Sales & Service Center
3990 East Market Street
York, PA 17402
Tel: (717) 755-2933
Fax: (717) 757-5063
Brazil
Apex Tool Group
Sales & Service Center
Av. Liberdade, 4055
Zona Industrial - Iporanga
18087-170 Sorocaba
SP Brazil
Tel: +55 15 2383929
Fax: +55 15 2383260
Canada
Apex Tool Group
Sales & Service Center
7631 Bath Road
Mississauga
Ontario L4T 3T1
Canada
Tel: (866) 691-6212
Tel: (905) 673-4400
China
Apex Power Tool Trading
(Shanghai) Co., Ltd
Building A8, No. 38
Dongsheng Road
Pudong, Shanghai
China 201201
Tel: +86-21-60880320
Fax: +86-21-60880313
England
Apex Tool Group
GmbH & Co. OHG
C/O Spline Gauges
Piccadilly, Tamworth
Staffordshire B78 2ER
United Kingdom
Tel: +44 1827 8741 28
Fax: +44 1827 8741 28
France
Apex Tool Group S.N.C.
25 rue Maurice Chevalier
B.P. 28
77831 Ozoir-La-Ferrière
Cedex, France
Tel: +33 1 64 43 22 00
Fax: +33 1 64 43 17 17
Germany
Apex Tool Group
GmbH & Co. OHG
Industriestraße 1
73463 Westhausen
Germany
Tel: +49 (0) 73 63 81 0
Fax: +49 (0) 73 63 81 222
Hungary
Apex Tool Group
Hungaria Kft
Platànfa u.2
9027 Györ
Hungary
Tel: +36 96 66 1383
Fax: +36 96 66 1135
India
Apex Power Tools India
Private Limited
Gala No. 1, Plot No. 5
S. No. 234, 235 & 245
Indialand Global
Industrial Park
Taluka-Mulsi, Phase I
Hinjawadi, Pune 411057
Maharashtra, India
Tel: +91 20 66761111
Mexico
Apex Tool Group México
S. de R.L. de C.V.
Vialidad El Pueblito #103
Parque Industrial Querétaro
Querétaro, QRO 76220
Mexico
Tel: +52 (442) 211-3800
Fax: +52 (442) 103-0443
Apex Tool Group, LLC
1000 Lufkin Road
Apex, NC 27539
Phone: 919-387-0099
Fax: 919-387-2614 www.apextoolgroup.com
PL31-15LN250/Printed in USA 12/2013/Copyright © Apex Tool Group, LLC
advertisement
Related manuals
advertisement