Genebre 1081 Manual

CMY

K

MY

CY

Y

CM

C

M

Cara manual 1081 (angles).pdf 1 18/6/20 12:26

Important information for correct disposal of the product

At the end of its useful life, the product cannot be disposed of as urban waste. It must be taken to a waste collection point, established by the competent authority or by suppliers specialized in this service. Recycling an electrical or electronic product in an adequate way avoids the negative consequences for the environment and for health derived from incorrect recycling and allows the raw materials that constitute it to be recycled, saving on natural resources and energy. As a reminder of the need to recycle electrical and electronic products properly, the product is marked with a crossed out container.

NON-CONTACT INFRARED THERMOMETER

Ref.: 1081

Scope of application

Used by families and medical departments when measuring body temperature. It can also be used to measure the surface temperature of objects.

Product features

• Strong environmental temperature adaptability, which can still be used normally in complex environment.

• New control probe structure to ensure more accurate measurement.

• Two measurement modes of body temperature and object temperature, one button mode switching operation is convenient and practical.

• Fever alarm prompt, backlight color prompt.

• Automatically save 16 sets of temperature measurement values.

• Large size LCD screen, high brightness three color backlight, clear and soft display.

• Two temperature units of Celsius and Fahrenheit can be selected.

• Automatic shutdown saves power and energy.

• Simple and clear operation mode.

Precautions

Please read this manual carefully before use, and make sure the battery is installed.

It is forbidden to immerse the forehead temperature gun in any liquid, and it is forbidden to use it in an excessively high or low temperature environment for a long time. It is forbidden to collide, fall, mix with sharp objects, and dismantle by yourself

Do not use in strong electromagnetic interference environment

Put the forehead temperature gun out of the reach of children.

The measurement results can't replace the doctor's diagnosis.

7

6 ey. tion is simple ared er e of ade is ernal pow e the body

3

1

4

5

, signal s the measurement k otection gr

, etc...

ture sensor empera ttery

. The user only needs ate

. Its opera y collecting the infr tely measur cura ture b t and accur ehead and pres he EU is classified as IIB.

, belonging to the int

CD display, ba ared t vice ement is fas orehead and hair empera ous oxide and other gases, and it is a t the for er, L

2 or wn ed detect over ttery c ch

.

7. Ba

6. Swit

5. Set button

4. Button up

3. Button do

2. LCD

1. Infrar oduct is mainly composed of infr y, buzz , ke essor ation equipment. T tion from the human f ector head a oduct is a class II medical de oduct measures the body t e atur common equipment (IP20). It can not be used under the mixtur

This pr temper to point the det rec

The pr continuous oper

This pr thermal radia

In one second, the user can quickly and ac eiving proc and sanitary, and its measur flammable anesthetic gas, nitr

Installation and use instructions supply equipment, type B application part, and the pr

F) o

0,4

F)

± o

F o onditions onditions) ement ement down with no action in 30 sec.

omatic shut

F) o

C) o e ( atur ture ( enheit temper empera ements ery warning w batt ery) A batt

C (0,54

F) e

~ 107,6 o o o o

0,3

C

±

C (0,4

C (95

0,3 o o

0,2 o

±

C:

C:

F) e measurement atur o ± al atur o

0,2 ±

C: o

F) ture measur empera o

F) ture measur

108,5 empera

F) o

85% (Under non-condensing c

85% (under non-condensing c

212,0

F) o

,6 ˜ ace t

7,6 e temper o o C

± 0.54

5 ~ 42

F o a corpor

5 ~ 42 ango 35 ~ 42

F) o

5 ~ 42 atur

C (14 ~ 131 o

C (32 ~ 10 o

≤

≤

~ 107,6

C (1,8

C (32 ˜

C (89 o o

100

42,5

5 cm.

o o

± 1

(95

Fuera del r

En rango 3

In range 3

T emper

0 ~

For Object surf

32 ~

For human body t

3 ~

Object surfac

0 ~ 42

RH

-10 ~ 55

RH

Human body temper

Out of range 3

DC1.5 V*2 (2 pcs AA

Lo

Memorize 16 measur

Fahr

Celsius t

Aut

149 x 77 x 43 mm (length x width x height)

104 g.

1 User Manual e acy ements down ting ambient tus e atur e atur age ambient ery sta wer Supply Po

Batt temper

Stor temper

Opera omatic shut

Product Measur

Aut

Weight

Annex

Display Unit

Memory function

Measuring Accur

Measuring distanc

Measuring range

Mean features. Technical parameters

Mean features. Technical parameters

Measuring distance

Measuring range

Measuring Accuracy

Operating ambient temperature

Storage ambient temperature

Power Supply

Battery status

Memory function

Display Unit

Automatic shutdown

Product Measurements

Weight

Annex

3 ~ 5 cm.

For human body temperature measurement

32 ~ 42,5 o C (89,6 ˜ 108,5 o F)

For Object surface temperature measurement

0 ~ 100 o C (32 ˜ 212,0 o F)

Temperatura corporal o

Out of range 35 ~ 42

(95 o ~ 107,6 o F ± 0.54

0,2 o C: o F) o o

± 0,3 o o

0,3 o o

F) o F

C (0,54 o

± 0,4

F) o F)

Object surface temperature

± 1 o C (1,8 o F)

0 ~ 42 o C (32 ~ 107,6 o F)

RH ≤ 85% (under non-condensing conditions)

-10 ~ 55 o C (14 ~ 131 o F)

RH ≤ 85% (Under non-condensing conditions

DC1.5 V*2 (2 pcs AAA battery)

Low battery warning

Memorize 16 measurements

Celsius temperature ( o C)

Fahrenheit temperature ( o F)

Automatic shutdown with no action in 30 sec.

149 x 77 x 43 mm (length x width x height)

104 g.

1 User Manual

This product measures the body temperature by collecting the infrared thermal radiation from the human forehead and hair. Its operation is simple and sanitary, and its measurement is fast and accurate. The user only needs to point the detector head at the forehead and press the measurement key.

In one second, the user can quickly and accurately measure the body temperature

This product is a class II medical device, belonging to the internal power supply equipment, type B application part, and the protection grade is common equipment (IP20). It can not be used under the mixture of flammable anesthetic gas, nitrous oxide and other gases, and it is a continuous operation equipment. The EU is classified as IIB.

The product is mainly composed of infrared temperature sensor, signal receiving processor, key, buzzer, LCD display, battery, etc...

Installation and use instructions

1. Infrared detector

2. LCD

3. Button down

4. Button up

5. Set button

6. Switch

.

7. Battery cover

2

5

4

1

3

6

7

MY

CM

Y

M

C

CY

CMY

K

atu till be used

, ture ement.

e of objects.

ttery is vironment empera amilies and medical departments when measuring body temper ed.

actical. e gun in any liquid, and it or's diagnosis.

ture en each of children. e sure the ba empera vironment atur ence en atur ement values.

te measur cura gy.

ee color backlight, clear and soft ture and object t ompt.

onvenient and pr ture measur empera e more ac ahrenheit can be select erfer e use, and mak e adaptability, which can s e temper e the surfac

, fall, mix with sharp objects, and ely high or low t ehead temper een, high brightness thr empera eplace the doct efully befor tion mode.

ompt, backlight color pr wer and ener o collide essiv ation is c onment.

atur e to ensur o immerse the for e units of Celsius and F ture gun out of the r o use it in an exc ong electromagnetic int ves po onmental temper empera ement results can't r orehead t ourself

. It is forbidden t x envir

. It can also be used to measur witching oper obe structur down sa ve 16 sets of t atur o measurement modes of body t e LCD scr ontrol pr ong envir omatically sa omatic shut o temper ver alarm pr

•

• Aut

• Fe

Large siz

• Aut

• Tw display.

• Tw

• New c one button mode s

• Str re

Used by f normally in comple

Product features

Scope of application

• Simple and clear opera

Precautions

Please read this manual car for a long time is forbidden t

It is forbidden t installed.

dismantle by y

Do not use in str

The measur

Put the f

Ref.: 1081

NON-CONTACT INFRARED THERMOMETER cle ect ecy tive ycling an y the ycled,

. Rec om incorr ed with a o be rec eminder of the need to r oduct cannot be disposed of as urban ed in this service or health derived fr ollection point, established b voids the nega ay a titute it t

, the product is mark oduct in an adequate w t cons gy. As a r oducts properly terials tha aste c e, the pr en to a w aw ma vironment and f esources and ener

. ws the r tural r es for the en ent authority or by suppliers specializ sed out container

. It must be tak te ycling and allo rec consequenc saving on na was

At the end of its useful lif compet cros electrical or electronic pr electrical and electronic pr

Important information for correct disposal of the product

Cara manual 1081 (angles).pdf 1 18/6/20 12:26

Mean features. Technical parameters

Measuring distance

Measuring range

Measuring Accuracy

Operating ambient temperature

Storage ambient temperature

Power Supply

Battery status

Memory function

Display Unit

Automatic shutdown

Product Measurements

Weight

Annex

3 ~ 5 cm.

For human body temperature measurement

32 ~ 42,5 o C (89,6 ˜ 108,5 o F)

For Object surface temperature measurement

0 ~ 100 o C (32 ˜ 212,0 o F)

Temperatura corporal o

Out of range 35 ~ 42

(95 o ~ 107,6 o F ± 0.54

0,2 o C: o F) o o

± 0,3 o o

0,3 o o

F) o F

C (0,54 o

± 0,4

F) o F)

Object surface temperature

± 1 o C (1,8 o F)

0 ~ 42 o C (32 ~ 107,6 o F)

RH ≤ 85% (under non-condensing conditions)

-10 ~ 55 o C (14 ~ 131 o F)

RH ≤ 85% (Under non-condensing conditions

DC1.5 V*2 (2 pcs AAA battery)

Low battery warning

Memorize 16 measurements

Celsius temperature ( o C)

Fahrenheit temperature ( o F)

Automatic shutdown with no action in 30 sec.

149 x 77 x 43 mm (length x width x height)

104 g.

1 User Manual

This product measures the body temperature by collecting the infrared thermal radiation from the human forehead and hair. Its operation is simple and sanitary, and its measurement is fast and accurate. The user only needs to point the detector head at the forehead and press the measurement key.

In one second, the user can quickly and accurately measure the body temperature

This product is a class II medical device, belonging to the internal power supply equipment, type B application part, and the protection grade is common equipment (IP20). It can not be used under the mixture of flammable anesthetic gas, nitrous oxide and other gases, and it is a continuous operation equipment. The EU is classified as IIB.

The product is mainly composed of infrared temperature sensor, signal receiving processor, key, buzzer, LCD display, battery, etc...

Installation and use instructions

1. Infrared detector

2. LCD

3. Button down

4. Button up

5. Set button

6. Switch

.

7. Battery cover

2

5

4

1

3

6

7

MY

CM

Y

M

C

CY

CMY

K

atu till be used

, ture ement.

e of objects.

ttery is vironment empera amilies and medical departments when measuring body temper ed.

actical. e gun in any liquid, and it or's diagnosis.

ture en each of children. e sure the ba empera vironment atur ence en atur ement values.

te measur cura gy.

ee color backlight, clear and soft ture and object t ompt.

onvenient and pr ture measur empera e more ac ahrenheit can be select erfer e use, and mak e adaptability, which can s e temper e the surfac

, fall, mix with sharp objects, and ely high or low t ehead temper een, high brightness thr empera eplace the doct efully befor tion mode.

ompt, backlight color pr wer and ener o collide essiv ation is c onment.

atur e to ensur o immerse the for e units of Celsius and F ture gun out of the r o use it in an exc ong electromagnetic int ves po onmental temper empera ement results can't r orehead t ourself

. It is forbidden t x envir

. It can also be used to measur witching oper obe structur down sa ve 16 sets of t atur o measurement modes of body t e LCD scr ontrol pr ong envir omatically sa omatic shut o temper ver alarm pr

•

• Aut

• Fe

Large siz

• Aut

• Tw display.

• Tw

• New c one button mode s

• Str re

Used by f normally in comple

Product features

Scope of application

• Simple and clear opera

Precautions

Please read this manual car for a long time is forbidden t

It is forbidden t installed.

dismantle by y

Do not use in str

The measur

Put the f

Ref.: 1081

NON-CONTACT INFRARED THERMOMETER cle ect ecy tive ycling an y the ycled,

. Rec om incorr ed with a o be rec eminder of the need to r oduct cannot be disposed of as urban ed in this service or health derived fr ollection point, established b voids the nega ay a titute it t

, the product is mark oduct in an adequate w t cons gy. As a r oducts properly terials tha aste c e, the pr en to a w aw ma vironment and f esources and ener

. ws the r tural r es for the en ent authority or by suppliers specializ sed out container

. It must be tak te ycling and allo rec consequenc saving on na was

At the end of its useful lif compet cros electrical or electronic pr electrical and electronic pr

Important information for correct disposal of the product

Cara manual 1081 (angles).pdf 1 18/6/20 12:26

Dors manual 1081 (angles).pdf 1 18/6/20 12:12

CMY

K

MY

CY

Y

CM

C

M

Instructions for use

Display icon definition

Icon definition

Icon

Electricity indication

Tone

Temperature measurement mode

Display Unit

Display value

Memory symbol o o

C

F

M

State description

Display

Display and flashing

The battery power is low and can only work for a short time. Please replace the battery.

The battery is too low to work properly. Please replace the battery immediately

No display

Display

No display

Full charged

Buzzer sound on, with prompt sound

Buzzer sound off, no prompt sound

Body temperature measuring mold.

Object Surface temperature measuring mold.

Celsius temperature.

Fahrenheit temperature.

It will show the measured temperatur

information.

Display value is memory value and group number.

16 sets of body temperature memory data queries

On the boot state, press the "up" or "down" button, LCD display the first memory value; each click the "+" or "-" button, display the memory number plus 1 or minus 1, a total of 16 groups of memory data.

Setting of tone switch

• In the power on state, press and hold "set" for 2 seconds, and the screen displays

F1,Press the "set" key 1 time it will show

F2.then press the "+" or "-" key to switch between prompt tone on and prompt tone off.

Temperature unit conversion settings

• In the power on state, press and hold "set" for 2 seconds, and the screen displays

F1,Press "set" key 2 times, it will show F3, then press the "+" or "-" key to switch between °C and °F

M

M o C o C

M

M o C o F

Safety instructions

Human body temperature measurement

After the batteries are installed, press the power on key for 1 second, and the power on is completed after the full display self check.

• Confirm that the measurement mode above the screen is body temperature mode (non object temperature mode)

• A lign the forehead temperature gun probe with the middle of the forehead and keep it vertical, with a distance of about 3-5cm. Press the measurement key to start the measurement. After about 1 second, the screen displays the measurement value. Press the measurement key for 5 seconds to shut down when no measurement is made, or shut down automatically after 30 seconds.

When 34 o C ≤ T ≤ 37,3 o

When 37,4 o C ≤ T ≤ 38 o

C, bright green backlight.

C, bright yellow backlight.

When 38,1 o C ≤ T ≤ 42,9 o

When T < 34 o

C, bright red backlight.

C,bright green backlight, display "LO"."

When T > 42,9 o C, bright red backlight, display "HI"."

Warm Tips:

1. Before and after use, please keep the sensor and probe cavity clean.

2. Please place the forehead temperature gun in a temperature stable environment for use. When ambient temperature changes greatly (e.g. from indoor to outdoor).

3. Do not begin to measure body temperature immediately after measuring the temperature of an object at very high or very low temperature. Please place it for ten minutes.

4. When the measurement object comes from a place that is quite different

Function Key Description o C

LCD Dispaly

Function setting key

M

+

-

Function key

SET

Function description

Enter / Exit the menu and switch the setup items

Select the confirmation item to look up the measured value

Select the confirmation item to look down the measured value

Setting up guidance

This product provides three function settings: measurement mode, tone switch, temperature unit, etc.The comparison table of setting menu is as follows:

Menu Function

F1

F2

Test mode

Test mode

“SET”Key

Press once

Press again

“+” Key

Object

Temperature

Model

Tips

“-” Key With prompt sound

Human

Temperature

Model

Human

Temperature

Model

No hint Tips

F3 Temperature unit

Press again o C o F

Body temperature setting / Object temperature

• Shortcut switch mode: in the boot state, short press "SET" key can realize the quick switch of human temperature and object temperature.

• In the power on state, press and hold "set" for 2 seconds, and F1 will be displayed on the screen, then press the "+" or "-" button to switch between "body temperature measurement" / "object temperature measurement".

M o C o C

M o C from the measured ambient temperature, it should stay in the test environment for at least five minutes.

5. Try not to measure in the forehead blowing, drenching water, sweating, coating, smear cosmetics, etc. Do not take body temperature within 30 minutes after exercise, bath, meal.

When the forehead temperature gun is out of working temperature, the screen will prompt: after the boot complete self-test, the screen will show the ambient temperature. When the working environment temperature is lower than 0 o C the screen will display “Err 1”, backlight red, when the ambient temperature is higher than 42 o C , the screen will display “Err 2”, backlight red.

Object temperature measurement

• Select object temperature mode.

• Aim the thermometer probe at the measuring target and keep it vertical, the distance is about 3-5 cm press the measuring key, display the temperature after about 1 second, when not measuring often press the measuring key for 5 seconds to shut down, or turn off automatically after 30 seconds.

Warm Tips:

1. The range of measurement of the temperature measurement mode of the object 0 o C - 100 o C

2. This function measures the object surface temperature and does not represent the object core temperature.

3. The emissivity of different materials may be different (refer to the emissivity of materials), and the measured temperature will deviate slightly from the actual temperature.

4. When the measured value is less than 0 o C , bright red backlight, display

"LO".. 5.When the measurement is higher than 100 o C , bright red backlight, display "HI".

Product maintenance and maintenance methods

Because the product is a reusable device, please pay attention to the cleaning process after use.

Please keep the inner cavity of sensor and probe clean, otherwise it will affect the measurement accuracy. Surface cleaning: wipe dirt with clean soft cloth or cotton stick with a little medical spray.

Clean the inner cavity of the sensor and probe: gently wipe the inner cavity of the head or the top of the sensor with a clean soft cloth or cotton stick with a little medical sprinkler. When the alcohol is completely volatile.

Storage conditions, methods

Products must be kept clean and kept in a dry place. Don't put the electronic forehead temperature gun in a place with electric shock. do not store the electronic forehead temperature gun in an extreme temperature environment above 55 o C or below -10 o C and humidity above 85%.

Dors manual 1081 (angles).pdf 1 18/6/20 12:12

CMY

K

MY

CY

Y

CM

C

M

Instructions for use

Display icon definition

Icon definition

Icon

Electricity indication

Tone

Temperature measurement mode

Display Unit

Display value

Memory symbol o o

C

F

M

State description

Display

Display and flashing

The battery power is low and can only work for a short time. Please replace the battery.

The battery is too low to work properly. Please replace the battery immediately

No display

Display

No display

Full charged

Buzzer sound on, with prompt sound

Buzzer sound off, no prompt sound

Body temperature measuring mold.

Object Surface temperature measuring mold.

Celsius temperature.

Fahrenheit temperature.

It will show the measured temperatur

information.

Display value is memory value and group number.

16 sets of body temperature memory data queries

On the boot state, press the "up" or "down" button, LCD display the first memory value; each click the "+" or "-" button, display the memory number plus 1 or minus 1, a total of 16 groups of memory data.

Setting of tone switch

• In the power on state, press and hold "set" for 2 seconds, and the screen displays

F1,Press the "set" key 1 time it will show

F2.then press the "+" or "-" key to switch between prompt tone on and prompt tone off.

Temperature unit conversion settings

• In the power on state, press and hold "set" for 2 seconds, and the screen displays

F1,Press "set" key 2 times, it will show F3, then press the "+" or "-" key to switch between °C and °F

M

M o C o C

M

M o C o F

Safety instructions

Human body temperature measurement

After the batteries are installed, press the power on key for 1 second, and the power on is completed after the full display self check.

• Confirm that the measurement mode above the screen is body temperature mode (non object temperature mode)

• A lign the forehead temperature gun probe with the middle of the forehead and keep it vertical, with a distance of about 3-5cm. Press the measurement key to start the measurement. After about 1 second, the screen displays the measurement value. Press the measurement key for 5 seconds to shut down when no measurement is made, or shut down automatically after 30 seconds.

When 34 o C ≤ T ≤ 37,3 o

When 37,4 o C ≤ T ≤ 38 o

C, bright green backlight.

C, bright yellow backlight.

When 38,1 o C ≤ T ≤ 42,9 o

When T < 34 o

C, bright red backlight.

C,bright green backlight, display "LO"."

When T > 42,9 o C, bright red backlight, display "HI"."

Warm Tips:

1. Before and after use, please keep the sensor and probe cavity clean.

2. Please place the forehead temperature gun in a temperature stable environment for use. When ambient temperature changes greatly (e.g. from indoor to outdoor).

3. Do not begin to measure body temperature immediately after measuring the temperature of an object at very high or very low temperature. Please place it for ten minutes.

4. When the measurement object comes from a place that is quite different

Function Key Description o C

LCD Dispaly

Function setting key

M

+

-

Function key

SET

Function description

Enter / Exit the menu and switch the setup items

Select the confirmation item to look up the measured value

Select the confirmation item to look down the measured value

Setting up guidance

This product provides three function settings: measurement mode, tone switch, temperature unit, etc.The comparison table of setting menu is as follows:

Menu Function

F1

F2

Test mode

Test mode

“SET”Key

Press once

Press again

“+” Key

Object

Temperature

Model

Tips

“-” Key With prompt sound

Human

Temperature

Model

Human

Temperature

Model

No hint Tips

F3 Temperature unit

Press again o C o F

Body temperature setting / Object temperature

• Shortcut switch mode: in the boot state, short press "SET" key can realize the quick switch of human temperature and object temperature.

• In the power on state, press and hold "set" for 2 seconds, and F1 will be displayed on the screen, then press the "+" or "-" button to switch between "body temperature measurement" / "object temperature measurement".

M o C o C

M o C from the measured ambient temperature, it should stay in the test environment for at least five minutes.

5. Try not to measure in the forehead blowing, drenching water, sweating, coating, smear cosmetics, etc. Do not take body temperature within 30 minutes after exercise, bath, meal.

When the forehead temperature gun is out of working temperature, the screen will prompt: after the boot complete self-test, the screen will show the ambient temperature. When the working environment temperature is lower than 0 o C the screen will display “Err 1”, backlight red, when the ambient temperature is higher than 42 o C , the screen will display “Err 2”, backlight red.

Object temperature measurement

• Select object temperature mode.

• Aim the thermometer probe at the measuring target and keep it vertical, the distance is about 3-5 cm press the measuring key, display the temperature after about 1 second, when not measuring often press the measuring key for 5 seconds to shut down, or turn off automatically after 30 seconds.

Warm Tips:

1. The range of measurement of the temperature measurement mode of the object 0 o C - 100 o C

2. This function measures the object surface temperature and does not represent the object core temperature.

3. The emissivity of different materials may be different (refer to the emissivity of materials), and the measured temperature will deviate slightly from the actual temperature.

4. When the measured value is less than 0 o C , bright red backlight, display

"LO".. 5.When the measurement is higher than 100 o C , bright red backlight, display "HI".

Product maintenance and maintenance methods

Because the product is a reusable device, please pay attention to the cleaning process after use.

Please keep the inner cavity of sensor and probe clean, otherwise it will affect the measurement accuracy. Surface cleaning: wipe dirt with clean soft cloth or cotton stick with a little medical spray.

Clean the inner cavity of the sensor and probe: gently wipe the inner cavity of the head or the top of the sensor with a clean soft cloth or cotton stick with a little medical sprinkler. When the alcohol is completely volatile.

Storage conditions, methods

Products must be kept clean and kept in a dry place. Don't put the electronic forehead temperature gun in a place with electric shock. do not store the electronic forehead temperature gun in an extreme temperature environment above 55 o C or below -10 o C and humidity above 85%.

Dors manual 1081 (angles).pdf 1 18/6/20 12:12

CMY

K

MY

CY

Y

CM

C

M

Instructions for use

Display icon definition

Icon definition

Icon

Electricity indication

Tone

Temperature measurement mode

Display Unit

Display value

Memory symbol o o

C

F

M

State description

Display

Display and flashing

The battery power is low and can only work for a short time. Please replace the battery.

The battery is too low to work properly. Please replace the battery immediately

No display

Display

No display

Full charged

Buzzer sound on, with prompt sound

Buzzer sound off, no prompt sound

Body temperature measuring mold.

Object Surface temperature measuring mold.

Celsius temperature.

Fahrenheit temperature.

It will show the measured temperatur

information.

Display value is memory value and group number.

16 sets of body temperature memory data queries

On the boot state, press the "up" or "down" button, LCD display the first memory value; each click the "+" or "-" button, display the memory number plus 1 or minus 1, a total of 16 groups of memory data.

Setting of tone switch

• In the power on state, press and hold "set" for 2 seconds, and the screen displays

F1,Press the "set" key 1 time it will show

F2.then press the "+" or "-" key to switch between prompt tone on and prompt tone off.

Temperature unit conversion settings

• In the power on state, press and hold "set" for 2 seconds, and the screen displays

F1,Press "set" key 2 times, it will show F3, then press the "+" or "-" key to switch between °C and °F

M

M o C o C

M

M o C o F

Safety instructions

Human body temperature measurement

After the batteries are installed, press the power on key for 1 second, and the power on is completed after the full display self check.

• Confirm that the measurement mode above the screen is body temperature mode (non object temperature mode)

• A lign the forehead temperature gun probe with the middle of the forehead and keep it vertical, with a distance of about 3-5cm. Press the measurement key to start the measurement. After about 1 second, the screen displays the measurement value. Press the measurement key for 5 seconds to shut down when no measurement is made, or shut down automatically after 30 seconds.

When 34 o C ≤ T ≤ 37,3 o

When 37,4 o C ≤ T ≤ 38 o

C, bright green backlight.

C, bright yellow backlight.

When 38,1 o C ≤ T ≤ 42,9 o

When T < 34 o

C, bright red backlight.

C,bright green backlight, display "LO"."

When T > 42,9 o C, bright red backlight, display "HI"."

Warm Tips:

1. Before and after use, please keep the sensor and probe cavity clean.

2. Please place the forehead temperature gun in a temperature stable environment for use. When ambient temperature changes greatly (e.g. from indoor to outdoor).

3. Do not begin to measure body temperature immediately after measuring the temperature of an object at very high or very low temperature. Please place it for ten minutes.

4. When the measurement object comes from a place that is quite different

Function Key Description o C

LCD Dispaly

Function setting key

M

+

-

Function key

SET

Function description

Enter / Exit the menu and switch the setup items

Select the confirmation item to look up the measured value

Select the confirmation item to look down the measured value

Setting up guidance

This product provides three function settings: measurement mode, tone switch, temperature unit, etc.The comparison table of setting menu is as follows:

Menu Function

F1

F2

Test mode

Test mode

“SET”Key

Press once

Press again

“+” Key

Object

Temperature

Model

Tips

“-” Key With prompt sound

Human

Temperature

Model

Human

Temperature

Model

No hint Tips

F3 Temperature unit

Press again o C o F

Body temperature setting / Object temperature

• Shortcut switch mode: in the boot state, short press "SET" key can realize the quick switch of human temperature and object temperature.

• In the power on state, press and hold "set" for 2 seconds, and F1 will be displayed on the screen, then press the "+" or "-" button to switch between "body temperature measurement" / "object temperature measurement".

M o C o C

M o C from the measured ambient temperature, it should stay in the test environment for at least five minutes.

5. Try not to measure in the forehead blowing, drenching water, sweating, coating, smear cosmetics, etc. Do not take body temperature within 30 minutes after exercise, bath, meal.

When the forehead temperature gun is out of working temperature, the screen will prompt: after the boot complete self-test, the screen will show the ambient temperature. When the working environment temperature is lower than 0 o C the screen will display “Err 1”, backlight red, when the ambient temperature is higher than 42 o C , the screen will display “Err 2”, backlight red.

Object temperature measurement

• Select object temperature mode.

• Aim the thermometer probe at the measuring target and keep it vertical, the distance is about 3-5 cm press the measuring key, display the temperature after about 1 second, when not measuring often press the measuring key for 5 seconds to shut down, or turn off automatically after 30 seconds.

Warm Tips:

1. The range of measurement of the temperature measurement mode of the object 0 o C - 100 o C

2. This function measures the object surface temperature and does not represent the object core temperature.

3. The emissivity of different materials may be different (refer to the emissivity of materials), and the measured temperature will deviate slightly from the actual temperature.

4. When the measured value is less than 0 o C , bright red backlight, display

"LO".. 5.When the measurement is higher than 100 o C , bright red backlight, display "HI".

Product maintenance and maintenance methods

Because the product is a reusable device, please pay attention to the cleaning process after use.

Please keep the inner cavity of sensor and probe clean, otherwise it will affect the measurement accuracy. Surface cleaning: wipe dirt with clean soft cloth or cotton stick with a little medical spray.

Clean the inner cavity of the sensor and probe: gently wipe the inner cavity of the head or the top of the sensor with a clean soft cloth or cotton stick with a little medical sprinkler. When the alcohol is completely volatile.

Storage conditions, methods

Products must be kept clean and kept in a dry place. Don't put the electronic forehead temperature gun in a place with electric shock. do not store the electronic forehead temperature gun in an extreme temperature environment above 55 o C or below -10 o C and humidity above 85%.

Dors manual 1081 (angles).pdf 1 18/6/20 12:12

CMY

K

MY

CY

Y

CM

C

M

Instructions for use

Display icon definition

Icon definition

Icon

Electricity indication

Tone

Temperature measurement mode

Display Unit

Display value

Memory symbol o o

C

F

M

State description

Display

Display and flashing

The battery power is low and can only work for a short time. Please replace the battery.

The battery is too low to work properly. Please replace the battery immediately

No display

Display

No display

Full charged

Buzzer sound on, with prompt sound

Buzzer sound off, no prompt sound

Body temperature measuring mold.

Object Surface temperature measuring mold.

Celsius temperature.

Fahrenheit temperature.

It will show the measured temperatur

information.

Display value is memory value and group number.

16 sets of body temperature memory data queries

On the boot state, press the "up" or "down" button, LCD display the first memory value; each click the "+" or "-" button, display the memory number plus 1 or minus 1, a total of 16 groups of memory data.

Setting of tone switch

• In the power on state, press and hold "set" for 2 seconds, and the screen displays

F1,Press the "set" key 1 time it will show

F2.then press the "+" or "-" key to switch between prompt tone on and prompt tone off.

Temperature unit conversion settings

• In the power on state, press and hold "set" for 2 seconds, and the screen displays

F1,Press "set" key 2 times, it will show F3, then press the "+" or "-" key to switch between °C and °F

M

M o C o C

M

M o C o F

Safety instructions

Human body temperature measurement

After the batteries are installed, press the power on key for 1 second, and the power on is completed after the full display self check.

• Confirm that the measurement mode above the screen is body temperature mode (non object temperature mode)

• A lign the forehead temperature gun probe with the middle of the forehead and keep it vertical, with a distance of about 3-5cm. Press the measurement key to start the measurement. After about 1 second, the screen displays the measurement value. Press the measurement key for 5 seconds to shut down when no measurement is made, or shut down automatically after 30 seconds.

When 34 o C ≤ T ≤ 37,3 o

When 37,4 o C ≤ T ≤ 38 o

C, bright green backlight.

C, bright yellow backlight.

When 38,1 o C ≤ T ≤ 42,9 o

When T < 34 o

C, bright red backlight.

C,bright green backlight, display "LO"."

When T > 42,9 o C, bright red backlight, display "HI"."

Warm Tips:

1. Before and after use, please keep the sensor and probe cavity clean.

2. Please place the forehead temperature gun in a temperature stable environment for use. When ambient temperature changes greatly (e.g. from indoor to outdoor).

3. Do not begin to measure body temperature immediately after measuring the temperature of an object at very high or very low temperature. Please place it for ten minutes.

4. When the measurement object comes from a place that is quite different

Function Key Description o C

LCD Dispaly

Function setting key

M

+

-

Function key

SET

Function description

Enter / Exit the menu and switch the setup items

Select the confirmation item to look up the measured value

Select the confirmation item to look down the measured value

Setting up guidance

This product provides three function settings: measurement mode, tone switch, temperature unit, etc.The comparison table of setting menu is as follows:

Menu Function

F1

F2

Test mode

Test mode

“SET”Key

Press once

Press again

“+” Key

Object

Temperature

Model

Tips

“-” Key With prompt sound

Human

Temperature

Model

Human

Temperature

Model

No hint Tips

F3 Temperature unit

Press again o C o F

Body temperature setting / Object temperature

• Shortcut switch mode: in the boot state, short press "SET" key can realize the quick switch of human temperature and object temperature.

• In the power on state, press and hold "set" for 2 seconds, and F1 will be displayed on the screen, then press the "+" or "-" button to switch between "body temperature measurement" / "object temperature measurement".

M o C o C

M o C from the measured ambient temperature, it should stay in the test environment for at least five minutes.

5. Try not to measure in the forehead blowing, drenching water, sweating, coating, smear cosmetics, etc. Do not take body temperature within 30 minutes after exercise, bath, meal.

When the forehead temperature gun is out of working temperature, the screen will prompt: after the boot complete self-test, the screen will show the ambient temperature. When the working environment temperature is lower than 0 o C the screen will display “Err 1”, backlight red, when the ambient temperature is higher than 42 o C , the screen will display “Err 2”, backlight red.

Object temperature measurement

• Select object temperature mode.

• Aim the thermometer probe at the measuring target and keep it vertical, the distance is about 3-5 cm press the measuring key, display the temperature after about 1 second, when not measuring often press the measuring key for 5 seconds to shut down, or turn off automatically after 30 seconds.

Warm Tips:

1. The range of measurement of the temperature measurement mode of the object 0 o C - 100 o C

2. This function measures the object surface temperature and does not represent the object core temperature.

3. The emissivity of different materials may be different (refer to the emissivity of materials), and the measured temperature will deviate slightly from the actual temperature.

4. When the measured value is less than 0 o C , bright red backlight, display

"LO".. 5.When the measurement is higher than 100 o C , bright red backlight, display "HI".

Product maintenance and maintenance methods

Because the product is a reusable device, please pay attention to the cleaning process after use.

Please keep the inner cavity of sensor and probe clean, otherwise it will affect the measurement accuracy. Surface cleaning: wipe dirt with clean soft cloth or cotton stick with a little medical spray.

Clean the inner cavity of the sensor and probe: gently wipe the inner cavity of the head or the top of the sensor with a clean soft cloth or cotton stick with a little medical sprinkler. When the alcohol is completely volatile.

Storage conditions, methods

Products must be kept clean and kept in a dry place. Don't put the electronic forehead temperature gun in a place with electric shock. do not store the electronic forehead temperature gun in an extreme temperature environment above 55 o C or below -10 o C and humidity above 85%.

CMY

K

MY

CY

Y

CM

C

M

Cara manual 1081 (angles).pdf 1 18/6/20 12:26

Important information for correct disposal of the product

At the end of its useful life, the product cannot be disposed of as urban waste. It must be taken to a waste collection point, established by the competent authority or by suppliers specialized in this service. Recycling an electrical or electronic product in an adequate way avoids the negative consequences for the environment and for health derived from incorrect recycling and allows the raw materials that constitute it to be recycled, saving on natural resources and energy. As a reminder of the need to recycle electrical and electronic products properly, the product is marked with a crossed out container.

NON-CONTACT INFRARED THERMOMETER

Ref.: 1081

Scope of application

Used by families and medical departments when measuring body temperature. It can also be used to measure the surface temperature of objects.

Product features

• Strong environmental temperature adaptability, which can still be used normally in complex environment.

• New control probe structure to ensure more accurate measurement.

• Two measurement modes of body temperature and object temperature, one button mode switching operation is convenient and practical.

• Fever alarm prompt, backlight color prompt.

• Automatically save 16 sets of temperature measurement values.

• Large size LCD screen, high brightness three color backlight, clear and soft display.

• Two temperature units of Celsius and Fahrenheit can be selected.

• Automatic shutdown saves power and energy.

• Simple and clear operation mode.

Precautions

Please read this manual carefully before use, and make sure the battery is installed.

It is forbidden to immerse the forehead temperature gun in any liquid, and it is forbidden to use it in an excessively high or low temperature environment for a long time. It is forbidden to collide, fall, mix with sharp objects, and dismantle by yourself

Do not use in strong electromagnetic interference environment

Put the forehead temperature gun out of the reach of children.

The measurement results can't replace the doctor's diagnosis.

7

6 ey. tion is simple ared er e of ade is ernal pow e the body

3

1

4

5

, signal s the measurement k otection gr

, etc...

ture sensor empera ttery

. The user only needs ate

. Its opera y collecting the infr tely measur cura ture b t and accur ehead and pres he EU is classified as IIB.

, belonging to the int

CD display, ba ared t vice ement is fas orehead and hair empera ous oxide and other gases, and it is a t the for er, L

2 or wn ed detect over ttery c ch

.

7. Ba

6. Swit

5. Set button

4. Button up

3. Button do

2. LCD

1. Infrar oduct is mainly composed of infr y, buzz , ke essor ation equipment. T tion from the human f ector head a oduct is a class II medical de oduct measures the body t e atur common equipment (IP20). It can not be used under the mixtur

This pr temper to point the det rec

The pr continuous oper

This pr thermal radia

In one second, the user can quickly and ac eiving proc and sanitary, and its measur flammable anesthetic gas, nitr

Installation and use instructions supply equipment, type B application part, and the pr

F) o

0,4

F)

± o

F o onditions onditions) ement ement down with no action in 30 sec.

omatic shut

F) o

C) o e ( atur ture ( enheit temper empera ements ery warning w batt ery) A batt

C (0,54

F) e

~ 107,6 o o o o

0,3

C

±

C (0,4

C (95

0,3 o o

0,2 o

±

C:

C:

F) e measurement atur o ± al atur o

0,2 ±

C: o

F) ture measur empera o

F) ture measur

108,5 empera

F) o

85% (Under non-condensing c

85% (under non-condensing c

212,0

F) o

,6 ˜ ace t

7,6 e temper o o C

± 0.54

5 ~ 42

F o a corpor

5 ~ 42 ango 35 ~ 42

F) o

5 ~ 42 atur

C (14 ~ 131 o

C (32 ~ 10 o

≤

≤

~ 107,6

C (1,8

C (32 ˜

C (89 o o

100

42,5

5 cm.

o o

± 1

(95

Fuera del r

En rango 3

In range 3

T emper

0 ~

For Object surf

32 ~

For human body t

3 ~

Object surfac

0 ~ 42

RH

-10 ~ 55

RH

Human body temper

Out of range 3

DC1.5 V*2 (2 pcs AA

Lo

Memorize 16 measur

Fahr

Celsius t

Aut

149 x 77 x 43 mm (length x width x height)

104 g.

1 User Manual e acy ements down ting ambient tus e atur e atur age ambient ery sta wer Supply Po

Batt temper

Stor temper

Opera omatic shut

Product Measur

Aut

Weight

Annex

Display Unit

Memory function

Measuring Accur

Measuring distanc

Measuring range

Mean features. Technical parameters