Traceable 5027 Instruction

Traceable 5027 is a multi-purpose digital timer that can be used for a variety of timing applications. It is a versatile device that can be used for a variety of applications, including count up/stopwatch timing, countdown alarm timing, and time-of-day clock. It has a large, easy-to-read LCD display measures 3 x 2½ x 1-inch and weighs only 2½ oz. making it easy to read from a distance. It is also accurate to 0.01% and has a resolution of 1 second, making it ideal for precise timing applications.

PDF

Document

TRACEABLE

SPECIFICATIONS

Display: ¾” high 5-digit LCD

Timing capacity: 9 hr, 59 min, 59 sec

TRIPLE-PURPOSE TIMER INSTRUCTIONS

ALL OPERATIONAL DIFFICULTIES

If this timer does not function properly for any reason, please replace the battery with a new high quality battery (see Battery Replacement section).

Resolution:

Accuracy:

1 sec

0.01%

Low battery power can occasionally cause any number of “apparent” operational difficulties. Replacing the battery with a new fresh battery will

Alarm:

Size/Weight:

1 min audible/visible

3 x 2½ x 1-inch, 2½ oz solve most difficulties.

Features: Count up/stopwatch timing, countdown alarm timing, time-of-day clock, 12/24 hour formats

BATTERY REPLACEMENT

A faint display, incorrect display, erratic display or no display are all indicators that the battery must be replaced. On back of unit, slide open the

CLEARING THE DISPLAY TO ZERO

Press CLEAR button to reset display to zero. In Timing mode CLEAR operates only if the timer is stopped. If the unit is timing, press START/STOP button to stop the timer before clearing display. battery cover. Remove the exhausted battery and replace with a new AAA alkaline battery. For proper placement, see drawing located inside battery compartment. Replace battery cover. Equivalent replacement battery:

Control No. 1105.

CLOCK SETTING

1. Press and hold CLOCK button for 3 seconds. Bottom left cursor blinks.

2. Press AM-PM button to select the proper setting.

3. Enter correct time (all six digits) using 0–9 buttons. Example: If time is

4:46:18, press 0, 4, 4, 6, 1, 8. Clock is set once the last digit is entered.

If an incorrect time is entered, press CLEAR button to clear the display.

4. Choose AM / PM or military time by pressing 12HR-24HR button located on back of unit.

COUNT-UP TIMING

1. Press COUNT-UP button (COUNT-UP appears on display).

2. Press START/STOP button to begin count up.

3. Press START/STOP button again to stop count up (see Time-Out section).

4. With count up stopped, press CLEAR button to return the display to

0:00:00.

WARRANTY, SERVICE OR RECALIBRATION

For warranty, service or recalibration contact:

CONTROL COMPANY

4455 Rex Road

Friendswood, Texas 77546 USA

Ph. 281-482-1714

Fax 281-482-9448

E-mail [email protected] www.control3.com

Control Company is ISO 9001 Quality-Certified by

DNV and ISO 17025 accredited as a Calibration

Laboratory by A2LA.

COUNTDOWN TIMING

1. Press TIMER button (TIMER appears on display).

2. If necessary, CLEAR the display.

3. Enter desired countdown time using buttons 0–9.

4. Press START/STOP button to begin countdown.

5. Press START/STOP button again to stop timing (see Time-Out section).

6. When timer reaches 0:00:00, it alarms, the display flashes and begins counting up to track elapsed time since alarming.

7. When the alarm sounds, pressing the START/STOP button silences the alarm, stops the count up, and returns the display to the previously programmed time. (Must be in Timer mode to halt count up and to return display to the preset time.) NOTE: Alarm sounds for 1 minute then stops automatically unless turned off manually. The count up continues until turned off.

TIME-OUT

If a pause in the countdown or count-up timing operation is required, press the start/stop button to “freeze” the display at the current reading (time-out).

To resume timing at the point it was stopped, press the start/stop button again. An unlimited number of time-outs may be performed.

Control Company Cat. No. 5027

Traceable ® is a registered trademark of Control Company

Hello! I am an AI chatbot specifically trained to assist you with the Traceable 5027 Operating instructions. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant is out of keyboard. Please, try again later.

Key features

Count up/stopwatch timing
Countdown alarm timing
Time-of-day clock
12/24 hour formats
Large, easy-to-read LCD display
Accurate to 0.01%
Resolution of 1 second
1 minute audible/visible alarm
Unlimited number of time-outs
Battery powered (AAA alkaline battery)

Frequently asked questions

Press the CLEAR button to reset the display to zero.

Press and hold the CLOCK button for 3 seconds. Bottom left cursor blinks. Enter correct time (all six digits) using 0–9 buttons.

Press the COUNT-UP button (COUNT-UP appears on display). Press START/STOP button to begin count up.

Press the TIMER button (TIMER appears on display). If necessary, CLEAR the display. Enter desired countdown time using buttons 0–9. Press START/STOP button to begin countdown.

When the timer reaches 0:00:00, it alarms, the display flashes and begins counting up to track elapsed time since alarming.

When the alarm sounds, pressing the START/STOP button silences the alarm, stops the count up, and returns the display to the previously programmed time.

If a pause in the countdown or count-up timing operation is required, press the start/stop button to “freeze” the display at the current reading (time-out).