Giant Alarm System JJ-PKM-C01 User Manual

GIANT ALARM SYSTEM CO.,LTD
CO.,LTD..
SWING GATE OPENER
JJ-PKM-C01 USER MANUAL
TEL NO.:86-595-22499516
FAX NO.:86-595-22492516
www.giantautogate.com
WEBSITE
WEBSITE：www.giantautogate.com
1
CAUTION: This product must be installed by well-trained skilled
professionals in compliance with the regulations concerning the field
swing gates opener device. Unqualified personnels or those who do
not know the standards applicable in this field should not carry out
the installation under any circumstances.
Every time must cut off power supply before starting installation,
operation or maintenance.
Please read the manual carefully before installation. Incorrect
installtion or misuse of product may cause seriously hurt on people or
damage on other objectives.
If the supplied wires damaged or broken, it must be replaced by
the manufacturer, its service agent or qualified persons in order to
avoid any hazard.
Keep the wireless control system (push-button, transmitters etc)
out of the reach of children.
Not allow children or other persons to stand near the motor
while in operation.
Not allow to use transmitters to control the gate when it is out
of sight.
Not allow to install the products at the place where is corrosive,
inflammable,and explosive.
The manually released part of front motor can not be installed
to the place where passerby could touch when gate closed.
Please keep this instruction for further reference.
2
1． PRODUCT DESPRICTION
2.SWING GATE OPENER TECHNICAL PARAMETERS
Input Voltage:
24VDC 40W
Rotational Speed：250RPM
Rod's Running Speed：1.6cm/s
Rod's Max Travel：300mm
Continue running time: 5min
Max Single-leaf Length：2.5m*2
Travel Max Single-leaf Weight：200KG
Environment Temperature：-20°C~+50°C
Protection Calss：IP55
3
3.SPEC SIZE
Fig.3
4
5.INSTALLATION DESCRIPTION
5.1 Required tools for installation
Fig.4
5.2 Installation diagram
Fig.5
Fig.6
5
5.3 Installation size
Fig.7
5.4 Description of installation
Fig.8
Different connecting method for front and rear bracket.
6
Using different installation method according to different
material and environment for front bracket.
Connection for rear bracket and motor
The height difference for installing the front and rear bracket.
Installation for front bracket
7
Open the gate manually:Release by spanner then lift it.
8
Swing gate opener cnotrol panel
Manual for Control Panel
1. Technical Parameters:
1. Control Panel Voltage Input: 220VAC
2. Motor’s Voltage: 12VDC/24VDC
3. Encoder For transmitter: Our own customed rolling code.
4. Support remote control:Can memorize 20PCS transmitters at most
5. Range of application: Suit for all double arms swing gate opener
9
2. Wiring diagram for control panel:
3. Functions and testing:
1. Indicator LED light: It’s always on once the system electrified. LED indicator
for “auto-closing”flashes every 1second. It turns off when enter into the learning code
state or removing code state; it flashes twice after successfully learning code or
removing code.
2. Transmitter : using our company own customed rolling code. Singe-leaf button
controls opening and closing of MOTOR2, double-leaf button simultaneously controls
opening and closing of MOTOR1 & MOTOR2. The control panel can memorize 20
transmitters at most.
3. Code-learning: press and hold learning button for 1second then release, LED
turns off and press any button of transmitter, then LED flashes twice, now the codes
has been learnt to the panel. If there is no any signals received within 5seconds, the
10
LED will light and then exit code-learning state .
4. Code-removing: press and hold learning button (once you press learning
button,LED is off), 5seconds later LED lights up, now the codes has been removed.
5, Instructions for all terminals:
This terminal is same as “double-leaves button” of transmitter.
2 SIDE
It controls the dual doors as Open-Stop-Close-Stop-Open
cyclically
This terminal is same as “Single-leaf button” of transmitter.
1SIDE
It controls the single door as Open-Stop-Close-Stop-Open
cyclically
COM
Common terminal for connecting ground
Wiring of motor1: should connect wires of the motor which opens
MOTO 1
first.Or connecting the wires of motor installed at the side of door
with thrust plate.
Wiring of motor2: should connect wires of the motor which you
MOTO2(DELAY)
could use single-leaf button to control.
Supply AC 12V*2 (switch high-speed running to low-speed
running)Supply DC 12V ( Motor only runs in low-speed, Need to
24V/12V-12V/0V-0V/12V
adjust HSPEED TIME trimmer to the minimum position)
Supply DC 24V &12V together (switch high-speed running to
low-speed running)
External 12V storage battery, the storage battery can be charged.
When there is no power supply, the UPS will start working
UPS+/-
automatically. The standby current of UPS when it is working is
20mA, the current is around 1.5A when the motor is
running.(specific current depends on the actual usage)
LOCK12+/-
Ternimal for Electric lock.
Swipe card to open two gates, active low, auto-closing is enabled
SWIPE CARD
after the door opened.
11
Terminal for photocells, active low, when the obstacle sensed by
INFRARED
photocell while the door is closing, the door will stop and then
rebound to open.
COM
Common terminal for connecting ground
12-28V output voltage; supply the power for photocells or other
VCC
saftey devices; current ≤200mA.
6. Motor running speed: Soft start when open and close the door, 700ms later
then switch to high-speed running. (Time adjusting: 0~33 seconds high speed time
can be adjusted by HSPEED TIME trimmer). When high-speed running time ends, it
switches into low-speed running till the motor stops running. When the motor stops in
the halfway for the first time during it runs from open limit position or close limit
position, then high-speed running time will adjust automatically based on previous
running time.
7. High-speed running time adjustment: Adjusting 0~30s high speed running
time through HSPEED TIME trimmer. When the trimmer turns to the minimum, it’s
0s, the high-speed running disabled, the motor keeps running in low-speed. Only
when both motors working, then high-speed running timing enabled.
8. Limit & obstacle sensitivity adjustment: During the opening and closing, the
motor stops running once the limit & obstacle sensitivity signals sensed. Sensitivity of
the two motors are set seperately. Adjusting the sensitivity of motor1 through
MOTOR1 trimmer, while MOTOR2 trimmer control sensitivity of motor2. Notice:
Arm-type motors only have the funcion of obstacle sensitivity, no functions of limit.
9. MOTOR1&2 opening/closing delay time adjustment: When opening the door,
motor2 opens first then motor1 opens later; while closing the door, motor1 closes first
then motor2 closes. And opening/closing delay time can be adjusted 0~30s.
10. Auto closing time adjustment: Auto closing funtion enabled when opening
the door by swiping the card which should have card-reader installed. Auto closing
time can be set for 0 second,5seconds and 10 seconds by using jumper. The auto
12
closing is disabled when you set 0 second. No jumper connected means 0 second.
When jumper 1 connect with jumper 2 it means 10 seconds. When jumper 2 connects
with jumper 3 it means 5 seconds. The LED indicator for auto closing time count
down flashes every 1second.
11. Motor delay time protection: As soon as the motor running continuously
more than 60s, the motor will automaticlly stop working to protect the motor.
12. Motor direction indentification:When one side of door installed thrust plate
or the contoller has function of setting order of opening & closing, or functions of
swiping card, make sure all the wiring connections of 2 motors are correct. When the
motor is running, if motor direction LED indicator is blue, now the motor should be in
“opening”operation, if no, please exchange the wiring connections of 2 motors; when
the motor direction LED indicator is RED, the motor should be in the
“closing”operation. If no, please exchage the wiring connections. Otherwise can not
open and close the door normally.
13