Rand McNally TND Tablet 1050 User manual

User Manual

FCC Compliance Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and may cause harmful interference to radio communications if not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet that is on a different circuit from the GPS unit.

• Consult the dealer or an experienced radio/TV technician for help.

When using the device, ensure that the antenna of the device is at least

20 cm away from all persons.

IC Compliance Statement

This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003.

IC Caution

Intentional or unintentional changes or modifications to the equipment not expressly approved by Rand McNally could void the user’s authority to operate the equipment.

IC attestation de conformité

Ce dispositif est conforme à la norme FCC Partie 15 et aux norme(s)

RSS permis-exempte(s) d’Industrie Canada. L’opération est soumise aux deux conditions suivantes:

3. Ce dispositif ne peut pas provoquer d’interférence nocive et

4. Ce dispositif doit accepter toute interference reçue, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositif.

Cet appareil numérique de la classe B est conforme à la norme

NMB-003 du Canada.

Attention

Les changements ou modifications à l’équipement, que ce soient intentionnelles ou non, non expressément approuvés par Rand McNally pourraient annuler l’autorisation de l’utilisateur à utiliser cet équipement.

IC: 10199A-10011A

TND™ Tablet 1050 User Manual i

TND™ Tablet 1050 User Manual

About GPS

The Global Positioning System (GPS) is a constellation of satellites that a GPS receiver uses to calculate geographical positions. To determine a position, data from at least three satellites is required. To determine elevation, the data from four or more satellites is required. Accuracy of the positioning varies from 10 feet to several hundred feet, depending on vehicle placement and the surrounding environment.

Geographical terrain (such as mountains), man-made structures (such as highway overpasses, bridges, and tall buildings), as well as weather can interfere with the GPS signal. For best GPS reception, position the device and mount with a clear line of sight to the sky. Some vehicles may have a limited view of the sky due to metal sun shields or a metallized windshield coating.

Map data includes the geographical coordinates for address locations and points of interest (POIs). With GPS reception, your device calculates a route to your selected location.

Customer Support

Web: randmcnally.com/support

Call toll-free:

877-446-4863

Service hours:

Monday through Friday, 7 a.m. to 6 p.m. CT

(Except official holidays)

E-mail:

[email protected]

ii

Table of Contents

Table of Contents

1. Your Device ...................................................................................... 1

What’s Included .............................................................................. 2

Mounting the Tablet ....................................................................... 3

TND™ Tablet 1050 Hardware .......................................................... 5

2. Getting Started ................................................................................. 6

Connecting to Wi-Fi ........................................................................ 6

Registration .................................................................................... 6

Navigating Your TND Tablet 1050 .................................................... 7

TND Tablet 1050 Settings ................................................................ 9

Android Settings ........................................................................... 10

3. Rand Navigation 2.0 ....................................................................... 11

Home Screen ................................................................................ 11

Navigation Settings ....................................................................... 12

Destination Search .......................................................................... 16

Single-line Search ........................................................................... 17

Guided Search .............................................................................. 18

Guided Search: New Location Menu ............................................... 19

Guided Search: Entering a New Location ........................................ 20

My Trips .......................................................................................... 21

Multi-Stop Trips .............................................................................. 22

Trails ............................................................................................... 23

History ............................................................................................ 24

Address Book Menu ................................................................... 25

Address Book: Contacts .................................................................. 26

Address Book: Groups .................................................................... 27

POIs ................................................................................................ 28


Filter POIs ....................................................................................... 29

POIs ................................................................................................ 30

Home and Work Locations.............................................................. 31

History & Bookmarks ...................................................................... 32

Route Map Window ...................................................................... 33

Exits .............................................................................................. 34

Route Options .............................................................................. 35

Route Overview ............................................................................ 36

Detour/Avoid ................................................................................ 37

Weather........................................................................................ 39

Traffic ........................................................................................... 40

Fuel .............................................................................................. 42

Virtual Dashboard. ........................................................................ 43

Fuel Logs ...................................................................................... 44

Junction View ............................................................................... 45

Turn View ..................................................................................... 45

Truck Tools .................................................................................... 46

4. TripMaker ® ..................................................................................... 47

5. Motor Carriers’ Road Atlas .............................................................. 48

6. Cameras ......................................................................................... 49

7. DriverConnect ................................................................................. 50

8. More Information ........................................................................... 51

Note: Some screens may appear slightly different depending

on device model and software version.

iii

Caution: Important Safety Information

Navigation

• Use this device at your own risk.

• Use this device only when it is safe to do so.

• Look at the display only when it is safe to do so.

• Traffic regulations always have priority over any instructions from the navigation system.

• Follow navigation system instructions only when local regulations and road traffic allow you do so.

• Make sure that the mount is securely mounted and properly adjusted before each trip.

• Note: If you do not understand the spoken instructions or are unsure of what to do next, refer to the navigation map on your navigation device.

Installation

• Make sure that the mount does not impair the driver’s visibility.

• Do not attach the mount within the airbag deployment zone.

• When installing the mount, make sure that it does not pose a risk in the event of an accident.

• Do not run cables directly next to safety-relevant devices and power supplies.

• After installation, check all safety-relevant equipment.

• Connect the wall charger to a 120V or 240V outlet only.

• Connect the vehicle charger to a 12V outlet only.

1. Your Device

Device

• Do not use sharp-edged objects on the device touch screen.

• The device is not waterproof and is not protected against water damage.

• Protect the device from extreme temperatures. Operating temperature for the device is between 32 degrees F and 120 degrees F.

• Do not open the navigation device casing.

• Do not attempt to replace the battery. Contact Rand McNally

Customer Support with questions about the battery.

• Always follow local regulations when disposing of this device.

• Note: Make sure that there are no kinks in the cable and that it will not be damaged by any sharp objects.

• Note: Use only a moist cloth to clean the navigation device.

• Note: Do not pull the cable to unplug the unit.

TND™ Tablet 1050 User Manual 1

1. Your Device

What’s Included

1 10-inch truck navigation device with camera

2

Powered magnetic mount connector

Three mounts:

3

4

Screw down mount

Suction cup mount

5 Ball mount bracket

6

Removable guard

7

Vehicle charger (5V/5A)

8

USB-C cable

9

Anti-glare screen protector

10

Quick Start Guide

9

1

3

5

4

2

6 7 8

10


1. Your Device

Mounting the TND™ Tablet 1050

Option 1: Screw Down Mount

Notes:

• Rand McNally recommends professional installation for this mounting option and is not responsible for any damages or consequences arising from the installation.

• Avoid gauges, HVAC, air bags, air bag covers and other items when drilling holes and attaching the mount to the vehicle.

• You need to furnish your own screws.

• This mount also includes an adhesive option.

1. Select an area with a line of sight to the sky and GPS satellites.

2. Clean and dry the mounting area.

3. Using the mount as a template, mark the three screw locations.

4. Drill pilot holes (optional).

5. Secure the mount in place with screws that you furnish.

6. Adjust the angle of the mount.

7. Plug the power cord into the mount and the vehicle’s 12-volt power source.

8. Snap the tablet onto the mount (using built-in magnet).

Option 2: Suction Cup Mount

Note: Follow all local regulations governing the placement of the mount.

1. Select an area with a line of sight to the sky and GPS satellites.

2. Clean and dry the mounting area.

3. Remove the suction cup protective film.

4. Adjust the angle of the mount.

5. Pull the suction cup lever up to release suction.

6. Plug the power cord into the mount and the vehicle’s 12-volt power source.

7. Place and hold the mount suction cup against the mounting surface.

8. Press the suction cup lever down until it snaps into place.

9. Snap the tablet onto the mount (using built-in magnet).


Mounting the TND™ Tablet 1050

Option 3: Ball Mount Bracket

The 1050 includes a ball mount that is compatible with third party mounting solutions.

1. Secure the ball mount to the magnetic mount using the screws included in the package. Note that the screws in the package might look slightly different than the screws in these images.

2. Snap the tablet on the mount (using built-in magnet).

1. Your Device


TND™ Tablet 1050 Hardware

Antenna Port

(antenna sold separately)

Power

Home

Volume

Down Up

USB-C

Micro HDMI

Audio out microSD card slot

Reset

1. Your Device

Camera



2. Getting Started

Powering Up

Charge the device before using it on battery power.

Note: GPS navigation will work right out of the box even if you do not have internet access.

Connecting to Wi-Fi

When you first turn on your tablet, you’ll be asked to select a Wi-Fi network to connect to the internet. A Wi-Fi connection is required to browse the web, download apps, and use internet- enabled features such as weather and traffic. Choose your wireless access point or hotspot from the list and type in your password. You can come back to this step later if you are in a place without internet access.

Warning: When using the magnetic mount in your vehicle, only use the mount's DC IN port for charging. Do not attempt to simultaneously charge the tablet from the magnetic mount and the tablet's USB port.

Registration

In the next step, you’ll be prompted to register your tablet with Rand McNally.

Your registration ensures that you have access to the latest information and updates, as well as Customer Support.

6

Navigating Your TND Tablet 1050

1

2

3

4

Android User Interface

1

Bluetooth

®

2

Wi-Fi

3

Battery Meter and Charging Indicator

4

Current time

5

Back

6

Return to home screen

7

View open apps


Note: You can swipe down from the top of the screen to view the Android quick settings menu.

5 6 7


1

3

Navigating Your TND Tablet 1050

6 7 8

4

2

5

Main Menu

1

Rand Navigation

2

Driver Apps (HOS/ELD)

3

Truck Tools

4

Cameras

5

Gallery

6

Guided search

7

Settings

8

App tray





TND Tablet 1050 Settings

• Wi-Fi – Connect to a wireless network.

• Connect to Car Stereo – Connect your headphone output to a

vehicle aux input.

• Android Settings– Opens the Android device settings screen.

• System Updates – Update your 1050.

• Data Repair – Fix missing or out-of-date files for your navigation system.

• About – View information about your device.

• Registration – Register your device.

9



Android Settings

• Network & Internet – Options for Wi-Fi, data usage, tethering,

VPN, and Airplane mode.

• Connected devices – Options for Bluetooth, Cast, printing, and USB.

• Apps & notifications – Options for notifications, app permissions, default apps, and access.

• Battery – Displays battery life and power options.

• Display – Options for brightness, wallpaper, sleep timers, and size.

• Sound – Options for media, alarm, and notification volume, do not disturb, and default sounds.

• Storage – Options for managing storage used by files and apps.

• Security & location – Options for setting screen lock preferences, location services, and other security settings.

• Users & accounts – Options for adding and managing user accounts and data synchronization.

• Accessibility – Options for screen readers, font sizes, magnification, and other ease-of-use settings.

• System – Options for language, time, and gesture settings, system information, and factory reset.

10

1

7 8


2

9 10 11

6

4

5

3

3. Rand Navigation 2.0

Rand Navigation

1 Single-line Search

Tap to enter a destination, address, or Point of Interest.

You can access any destination from the single-line search.

2 Battery Meter

Displays battery power status and charging indicator.

3 Map View Mode

Tap to switch the map view between 3D map, North up, or Heading up.

4 Wi-Fi Connected Services

Tap to show fuel prices, weather and traffic on the map.

5 Zoom

Tap + or - to zoom in or out on the map.

6 Return to current location

If viewing another map area, tap this icon to return focus to your current location.

7 Virtual Dashboard

Tap to view a variety of information concerning your current trip.

8 Street/Intersection/Location

Tap to toggle between the current street name, the upcoming intersection, or your current location.

9 Local Time/Elevation

Tap to toggle between displaying local time or elevation.

10 Navigation Settings

Tap to access settings such as: General, Truck Info, Route, Map, and Warnings.

11 Full Screen

Tap to change the view to full screen.

11

Navigation Settings

To access navigation settings, tap the gear icon in the bottom-right of the Rand Navigation Home Screen.

After adjusting any settings, tap the B ack icon in the upper-left to return to navigation.

General Options

Language English

Español

Français

For the screen and spoken instructions.

Units Automatic

Metric

U.S. Standard

Clock 12-hour format

24-hour format

Note: Some tools and settings may not be available in car mode.

Yard Time Zone Hawaii-Aleutian time

Alaska time

Pacific time

Arizona

Mountain time

Central time

Eastern time

Indiana (East)

Atlantic (Canada) time

Newfoundland time

Vehicle Type Truck

Bus

Car/Light truck

Controls how routes are calculated.



General Options

Load Prompt Enabled

Always loaded

When enabled, the system will ask if the truck is loaded or not every time you start a trip or a new leg.

Mileage Log Truck & bus

Car only

Truck & car

Disabled

Custom POIs Tap to display the list of custom

Points of Interest and control if they appear on the map.

Touch Sound

System Settings

Data Repair

Display Android System sound settings.

Tap to display Android System settings.

Tap to fix missing or out-of-date files for your navigation system. An internet connection is required.

System Update

Tutorial

Contact & About

Legal Notices

Tap to perform system update.

View getting started tutorial.

Tap to show version information and customer support contact information.

End user responsibilities and credits.

12

Truck Info

Hazmat Type

Weight (Empty)

Weight (Loaded)

Height

Width

Trailers

Number of Axles

Options

None

Explosives

Gases

Flammable Liquids

Flammable Solids

Oxidizers

Poison

Radioactive

Corrosives

PIH

Other

Click the pencil icon to enter a

numeric value.

Click the pencil icon to enter a

numeric value.

See Load Prompt in General preferences.

Click the pencil icon, and use the dials

to select your vehicle’s height.

Click the pencil icon, and use the dials

to select your vehicle’s width.

Straight

48'

53'

Double

Triple

Use the dial to select the number of axles.


Route Options

Traffic On/Off slider (requires Wi-Fi connection)

Recalculation Auto

Manual

Preferred Route

ETA Adjustment

Fastest route

Shortest route

ETA ok

Increase ETA some

Increase ETA more

Decrease ETA some

Decrease ETA more

Set adjustments to your ETA due to weather or traffic conditions. You can add (increase) time to make the trip take longer or subtract (decrease) time to make the trip take less time.

Turn Announcements

Junction Views

Route Avoids

Permanent Avoids

Set three distances at which you want to be warned about an upcoming turn.

The first announcement will be the farthest from the turn and the third the closest to it.

Set the distance before an upcoming maneuver at which the highway junction view screen appears.

Select/de-select from the list of options:

Tollways, Freeways, Ferries, Tunnels,

Small roads, U-Turns, Cross country borders,

Dirt roads.

Tap to manage your list of areas and roads to permanently avoid.


Map Options

Day/Night Mode Automatic

Day

Night

Route Color Tap a color to select.

Map View Mode

Map Auto Zoom

Heading up

North up

3D view

On/Off slider

Auto scale

Street scale

City scale

State scale

Set to street/city/state scale to specify the maximum scale of the zoom.

Lane Guidance On/Off slider

When on, the map guides you to the correct lane in preparation for upcoming

turns.

POI Icons On/Off slider

Select categories of icons to display on map.

Select restaurants, banks, and other consumer POIs to display on the map.

Tap any category to fill in the square and display those icons.


Map

Truck POI Icons

Address B ook Icons

Truck Icon

B us Icon

Car/Light truck Icon

Options

On/Off slider

Select icons to display on map.

Select travel centers, service, weigh stations and truck POIs to display on the map. Tap any category to fill in the square and display those icons.

On/Off slider

Address book entries appear as pushpin icons unless they are assigned to a group.

Use the arrows to set the truck icon to display when using the truck setting.

Use the provided colors to set the truck icon color.

Use the arrows to set the bus icon to display when using the bus setting.

Use the provided colors to set the bus icon color.

Use the arrows to set the car icon to display when using the car setting.

Use the provided colors to set the car icon color.


Warnings Options

Warning Type None

Audio & visual

Visual only

Audio only

Auto Dismiss Warnings Never

After 2 seconds

After 10 seconds

After 30 seconds

Height and weight violations will not be auto dismissed.

Curve Warnings On/Off slider

Click the pencil to manually edit, or use the slider to set distance.

Hill Warnings On/Off slider


Engine B rake Warnings On/Off slider


Narrow Road Warnings On/Off slider


Construction Area On/Off slider



Warnings Options

Speed Limit

Speed Limit Change

On/Off slider

Set the amount over the posted limit at which the warning appears.

Set a user-defined maximum speed to be warned whenever the truck exceeds that speed, regardless of posted speed limits.

On/Off slider


Weigh Station On/Off slider


State/Province B order On/Off slider


Timezone Change

Toll B ooth Alert

Maintenance

On/Off slider

On/Off slider


On/Off slider


7 1

3

4 5

2

6


Destination Search

To access this window from the Rand Navigation Home Screen, tap Where to?

1

2

Single-line Search

Tap here to bring up a keyboard and start typing to search for a destination.

Guided Search

Tap to access the guided search options.

3 Points of Interest

Tap to search for a point of interest (POI), such as a travel center, restaurant, etc.

4 History

Tap to route to a recently entered location.

5

6

B ookmarks

Tap to view a list of saved locations.

Distance

Displays the distance to each destination in the list.

7

B ack

Tap to return to the navigation screen.


6

6

7

4

1

2

5

3


Single-line Search

To access the single-line search window from the Rand Navigation

Home Screen, tap Where to?

From this screen, you can tap in the search bar to bring up a keyboard and begin typing an address, point of interest, or any other destination type.

The single-line search will return matching results below.

1

2

Address/Text Search

Search for addresses, streets, cities and points of interest.

• Address searches should include either a city or postal code.

• Avoid using punctuations.

• Avoid using street prefixes and suffixes.

Matching Results

Destinations that match your search terms display here. The address, city, and state display to the left. The distance from your current location displays on the right. Tap a destination to begin navigation.

3 See on Map

Tap to view the listed destinations on a map in a split-screen view.

4 Selected Destination

Tap a destination from the list to select it. The address, coordinates, and Motor Carriers’ Road Atlas reference page are displayed.

5

6

Navigate

Tap to begin navigation to the selected destination.

B ack

Tap to return to the previous screen.

7 Go to Map



8 9

1

5

2

6

3

7

4


Guided Search

To access Guided Search, either tap Guided Search from the top-right of the Single-line Search screen, or tap the magnifying glass icon from the Main Menu.

1 New Location

Tap to route to a destination by address, city center, intersection, or latitude and longitude coordinates.

2 My Trips

Tap to review your saved trips.

3 History

Tap to review your recent destinations.

4 Address B ook

Tap to select a destination from your Address Book.

5 POIs

Tap to begin a point of interest search.

6 Add Home

Tap to route to your stored Home location.

7 Add Work

Tap to route to your stored Work location.

8 Back

Tap to return to the previous screen.

9 Go to Map



1 2 3 4


New Location Menu

1

2

Address

Navigate to an address by entering the city (or postal code), street, and house number.

City Center

Navigate to a city center.

3 Intersection

Navigate to the intersection of two roads within a specified city.

4 Coordinates

Navigate to a location by entering its numeric latitude and longitude.

5 Navigate

Once you select your destination through the guided search, click the Navigate button to begin navigation.

5



3

2

1

4

5


Entering a New Location

The Guided Search Keyboard helps you quickly locate your destination.

1

2

Auto-Complete Keyboard

As you key in characters, the keyboard only displays next possible letters or numbers. Letters and numbers that cannot be entered in sequence are disabled. Search results are displayed as you key in characters.

Destination Entry

The top bar displays the current search entry.

3 Guided Search: City/Postal Code

Displays the available city/postal code selections based on the information you entered. Tap a result to advance.

4 Guided Search: Street

Displays the available street name selections based on the city you selected, and the information you entered. If the next letter in the street name cannot be selected on the keyboard, tap Expand Search to search a larger area. Tap a result to advance.

5 Guided Search: House Number

Displays the available house numbers based on the city and street selected, and the information you entered. Tap a result to advance.

20


1 2


My Trips

1

2

Multi-Stop Trips

Tap to view a list of saved multi-stop trips or to create a new one.

Trails

Use Trails to record a “bread-crumb” path where your truck travels.

21

2

1


Multi-Stop Trips

Displays a list of recent destinations.

1

2

Tap to review and edit a saved trip.

Tap + NEW TRIP to create a new multi-stop trip.

3 Trip details:

Displays the stops along your trip.

Tap the X to remove a stop.

Tap + Add a Location to add a new stop.

3

5 4

6


7

8

4 Tap to view Route avoids, Route details, and Overview.

Also tap to Save to My trips.

5

6

Tap to Reverse or Reorder your stops (manually or automatically).

Displays the travel time, traffic delays (if any), and estimated toll

costs for the first leg of your trip.

7 Tap to compare and select alternate routes.

8 Tap to begin navigation.

22

2

1

3


Trails

Use Trails to record a “bread-crumb” path where your truck travels.

The Trails feature is beneficial when traveling in areas where there is no marked road network.

1

2

3

Tap to open an existing trail.

Tap to record a new trail.

Tap to edit or delete a trail.

4


5

7

6

4 Tap to stop recording.

5 View details about the trail.

6 Tap to begin navigation. Routing to an existing trail will take you to the start of the trail. You can then follow the rest of the trail to your

destination.

7 Tap to edit or delete the trail.

23


1

3

2


History

Displays a list of recent destinations.

1 Recent Destinations

Tap an entry in the list to navigate to the destination.

2 Distance

Displays the distance to each destination from your current

location.

3 Options

Tap to access additional options:

• Edit: Allows you to select and delete an entry from the history list.

• Clear History: Deletes all entries.

24

5


1 2 3

7

4


Address Book Menu

Displays your saved bookmarks, contacts, and groups.

1

2

Bookmarks

Navigate to a saved address.

Contacts

Navigate to a stored address from a saved contact.

Note: Contacts are stored in the Contacts app. You can add contacts manually or import them.

3 Groups

Organize your bookmarks and contacts in groups.

6

Address Book: Bookmarks

4 Destinations

Tap a bookmark to navigate to the destination.

5

6

Alphabetic Organization

Tap a letter group to view bookmarks alphabetically. This is useful if you have a lot of bookmarks and they are difficult to find.

Options

Tap to search, sort, edit, add or delete bookmarks.

7 New bookmark

Tap to add a new bookmark.

25


3

4

1

2


Address B ook: Contacts

In order to use contacts for navigation, you first need to set them up in the

Rand Navigation 2.0 app. You can add contacts manually or import them.

1

2

Add a New Contact

Tap to manually create a new contact.

Search

Tap to search for an existing contact.

3 Contacts

Tap a contact’s name to view and edit information about that

contact.

4 Create New Contact screen

Enter information about the contact.

Tap Save to save and return to the previous screen.

26

1


Address B ook: Groups

Use Groups to organize your contacts and destinations into categories for easier searching.

1

2

Groups

Displays groups you have created.

New Group

Tap to create a new group.

2


3

5

4

3 Group Destinations

Displays the destinations stored in the selected group.

Tap a destination to begin navigation.

4 Group Options

Tap in the corner to edit or delete destinations in a group.

5 Add Location

Tap to add a new location to the group.

You can add a new address or select from your history, bookmarks, or POIs.

27


1 2 3 4


POIs

Displays Points of Interest (POIs) near your current location, near a specific location, along your intended travel route, or near your destination.

1

2

My Truck

Tap to display POIs near your current location.

A city

Tap to display POIs near a specific city.

3 My route

Tap to display POIs along your route if you have one set.

4 My destination

Tap to display POIs near your destination if you have one set.

5

5

6

POI Categories

Tap to select the POI category.

Note: Some categories may have multiple subcategories.

Custom POI

Tap to display custom POIs from an import.

7 Quick Stops

Displays a list of commonly-searched POI categories.

6 7

28

7

1

4 3

2

5


Filter POIs

Truck-related points of interest such as Travel Centers and Truck Services can include several amenities. To review only the locations with particular amenities you can filter your search results.

1

2

Nearby Places

Lists destinations near your location that match the selected category.

Map

Displays destinations near your location.

3 Filter

Search for points of interest by available services.

4 Search

Search for points of interest by name.

5

6

7

Tap a checkbox for a subcategory to include it in your search.

Tap to clear the filters.

Tap to go back and view the filtered POI list.

Note: Filter selections will remain active until you clear them.

6


1

2

4


5

3


POIs

When you select a POI category, the system will display suggestions provided by Yelp (if available) and other nearby places.

Note: A Wi-Fi connection is required in order to display Yelp information.

1

2

Yelp Suggestions

Displays top-rated suggestions from Yelp. Tap a destination to view additional information and begin navigation.

Nearby, Along route or My destination

Displays matching POIs near the location specified along with the distance to each destination. Tap a destination to view additional information and begin navigation.

3 Map

Displays POIs near your truck, a city, your route, or your destination.

4 More information

Displays additional information about the POI, including Yelp review information, address and phone number.

Tap the Reviews link to view reviews on yelp.com.

5 POI Destination

Displays the selected POI on the map, along with the locations of other nearby places.

6 Navigate

Tap to begin navigation to the selected POI.

6

30

5


1

2

4

3


Home and Work Locations

You can set bookmarks for a Home and a Work location. This is useful so you can quickly navigate to these destinations.

Tap Add Work or Add Home to set these locations.

1

2

Select Location

Tap New Location, History, or POIs to set a Home or Work destination from among these options.

Choose on Map

Tap to set your Home or Work location by selecting a point on the map.

3 Use Current Location

Tap to set your Home or Work location to your current location.

4 Create/Remove ookmark

Use this button to create or remove a bookmark.

5

6

Home/Work Information

Displays information about your Home or Work location.

Navigate

Tap to navigate to Home or Work.

6

31


History & B ookmarks

1 History

Displays previous destinations. Tap a destination to begin navigation.

1


2

2

B ookmarks

Displays your saved locations. Tap a location to begin navigation.

32


Route Map Window

17

1

18

19

2

5

3

7

8

9

10

11

4

6

16 15

1 Next Maneuver

Instructions for your next maneuver.

14 13 12

2 Road Name

Next maneuver street name or highway sign.

3 Exits

Check upcoming exits for food, gas, hotels and other places.

4 Route Options

Tap to display additional options, including adding a stop, detours, and ending navigation.

5 Current time and time zone

6 Map View Mode

Tap to switch the map view: 3D map, North up, or Heading up.

7 Battery power status and charging indicator

8 Wi-Fi Connected Services

Tap to enable fuel prices, weather and traffic on the map.

Note: These options require a Wi-Fi connection.


9 Zoom In/Zoom Out

10 Announcements

11 Distance remaining to your destination

Displays a progress bar indicating the distance remaining to your destination.

12 Expanded Map Display

Tap to remove additional options from the map screen.

13 Settings

Tap to open the Navigation Settings screens.

14 ETA/Time/Distance

Tap to toggle between displaying ETA, Yard ETA, Remaining Time,

Yard Time, and Elevation.

15 Location View

Tap to toggle between displaying the current location by city, street name, or next cross street.

16 Virtual Dashboard

Tap to view information about your current location, route, trips, and more.

17 Current Speed

Displays your current speed and turns red for speed warnings.

18 Speed Limit

Posted speed limit for your vehicle setting.

Tap to open a screen to submit a speed limit correction.

19 Map

Displays the map, your current route, and your vehicle’s current location.

17

33


1

2

3


Exits

Slide out to show points of interest at upcoming exits.

The list displays the distance to the next exit, exit name and number, and a count of available amenities.

1 Tap on an exit to display a list of POIs at the exit.

2 Tap the icon to display locations by category.

3 Tap on any item in the list to view additional information or to route to the POI.

34

1

3

5

Trip Summary (for multi-stop trips)

7


8

2

4

6

Route Options

1 Route Overview

Displays the directions, highways, and summary of your trip.

2 Save Trip

Tap to save a new trip with different color settings and a note field.

3 Add Stop

Tap to add additional destinations to your route.

4 Detour/Avoid

Tap to manage locations to avoid on the route and automatically calculate detours around them.

5 Route Settings

Tap to open the Route tab of the Settings screen.

6 Skip to Next Stop

Tap to skip the next destination in your route and continue.

7 Stop Navigation

Tap to cancel the current route and return to the home screen.

8 Exit

Tap to close Route Options and resume navigation.


Directions Tab

1

Highways Tab

2

Summary Tab

3

Route Overview

1 Directions Tab


Displays the turn-by-turn directions for the current route.

2 Highways Tab

Displays only the highways along your route, with the number of miles to travel on each.

3 Summary Tab

Displays the total travel time and distance for your route, as well as summaries for each leg of the trip for multi-stop trips.




Detour/Avoid

From Route Options, tap Detour/Avoid. There are four options available to set up detours and permanent avoids:

1 Next miles allows you to detour a certain number of miles.

Use the slider to set the number of miles to detour/avoid.

2 A road allows you to avoid a specific road.

3 An area allows you to draw a polygon on the map to avoid.

4 Along the route allows you to select a step in your navigation to avoid.

When selecting next miles, use the slider to set the number of miles that are next along your route to avoid. Tap Detour to being using the new route.

37


1

2


Detour/Avoid

When selecting A road , zoom in and out on the map to center the target over the road to avoid. The road is highlighted in red. Tap Permanent

Avoid to always avoid it. Tap Detour to avoid it on this trip only.

When selecting An area , tap on the map to set points for an area to avoid. Tap Permanent Avoid to always avoid it. Tap Detour to avoid it on this trip only.

3

When selecting Along the route , select the step on the route you wish to avoid. Tap Detour to navigate around it.

38

3

4

2

1

6

5


Weather

When enabled, Weather displays current weather condition overlays on the map.

Notes:

• Requires a Wi-Fi connection.

• The refresh speed of the weather display is dependent on your connection speed. Weather information is updated every few minutes when a Wi-Fi connection is active.

• Weather display depends on active weather patterns and map zoom level.

To view current weather information and the three-day forecast for your location, tap the gear icon on the map screen and tap the Weather slider.

1 Tap to enable weather.

2 Tap to view details and enter settings.

3 Select to view weather at your current location or at your destination.

4 Current weather conditions at the selected location.

5 Three-day forecast for the selected location.

6 Tap to view and change weather overlay preferences such as layer opacity and weather type.



2 1


Traffic

To view traffic information, tap the gear icon on the map screen and then the Traffic slider. Traffic conditions will overlay on the map when traffic is enabled.

Note: Requires a Wi-Fi connection.

1

2

Tap to enable traffic.

Tap to view details and enter settings.

4

3

5

4

5

3 Select to view traffic flow, incidents, or all.

Current traffic conditions/incidents along your route.

Your distance to the traffic conditions/incidents.

40


Traffic Icons

Accident Danger Traffic Event Closure Carriageway Police

Exit

B

locked Entrance

B

locked Delay

Rain Snow

Spillage Road Work Road Weather

Rock Fall High Temperature Low Temperature Ice

Wind Thunderstorm Tornado Blizzard Avalanche Fog

Size Limit


Weight Limit Visibility

Heavy

Traffic

Moderate

Traffic

Traffic Standstill

41


2

1


Fuel

To view fuel price information, tap gear icon on the map screen and then the Fuel slider. Current fuel prices will overlay on the map at various stations when enabled and available.

Note: Requires a Wi-Fi connection.

1 Tap to enable fuel prices.

2 Tap to view details and enter settings.

3

4

6

5

7

3 Select to view fuel prices either nearby or along your route.

4 Displays the fuel stations based on the criteria you selected.

5 Displays the distance to each station.

6 Sort by distance or price.

7 View and change fuel preferences such as fuel types and

stations to display on the map.

42

13

7

2

6

4

9

3

10 11

5

12

1

8


Virtual Dashboard

1 Current location.

2

Current times at the yard, current location and destination, as well as estimated time of arrival.

3 Sunrise and sunset times based on vehicle location

(latitude/longitude) and time of day.

4 Current speed (above) and posted speed limit (below).

Note: Turns red when speed limit warning exceeded.

5 Elevation at current location.

6 Current leg progress.

7 Information for up to three trips. Includes odometer, time and speed information.

8 Nearest cross street.

9 Current day and date at your location.

10 Battery power status and charging indicator

11 Return to the route map.

12 Add fuel purchase information.

13 Distance to next maneuver.




Fuel Logs

1. From the Virtual Dashboard, tap Add Fuel .

2. Tap a field to enter information. You can edit the following fields:

Date, Taxable, Fuel quantity, Fuel price, Total cost, Location, Station,

Last odometer, and Current odometer. Distance, Current economy, and Average economy are calculated automatically based on your entries.

3. Tap Save to record a fuel purchase.

44


1

4

2

3


Junction View

When on a route, Junction View displays when you have an upcoming maneuver. Set distance in Settings > Route . Once past the maneuver,

Junction View closes and the previous window displays.

1 Signs to follow for the next maneuver. Includes exit number and highway name/number if applicable.

2 Distance to the upcoming maneuver. Distance decreases as you approach.

3 Lane assist arrow.

4 Return to previous window.

Turn View

Displays for upcoming turns. Set distance in Settings > Route .

45


1

4

2

5

3

6

9

12

7 8

10 11


Truck Tools

To access, tap Truck Tools from the Main Menu.

1 Status, Mileage & Fuel

View driving information, mileage logs, and fuel purchase

information.

2 Quick Planner

Quickly calculate the distance, driving time, and cost to travel between any two cities or towns.

3 Tell Rand

Compose a message to send to Rand McNally.

4 Import Data & Export Data

Transfer address books, custom POIs, and saved trips from your old

TND device or to a new one.

5 Rand Motor Carrier’s Road Info

View Rand McNally’s index of helpful roadside emergency contact information and truck regulations.

6 Rand Motor Carrier’s Road Atlas

A digital version of Rand McNally’s Motor Carriers’ Road Atlas.

7 BackUp

8 Get Apps

Install third-party Android app stores (requires Wi-Fi).

9 Notes

10 Calendar

11 Calculator

12 Unit Converter

Quickly convert distance, weight, temperature, and many more.

46


4. TripMaker

®

TripMaker

To access TripMaker, tap the App Tray icon on the home screen.

TripMaker is a trip planning app that allows you to easily browse the map and set up a multi-stop trip. Add via points and send your trip to the Rand

Navigation 2.0 app for truck-friendly routing.

Please note that TripMaker does not provide truck routing.

View Help in the TripMaker app to learn more.

47


5. Motor Carriers’ Road Atlas

Motor Carriers’ Road Atlas

A digital version of Rand McNally’s Motor Carriers’ Road Atlas.

Tap Maps at the top right to select pages by state.

Tap Legend at the left to view the map legend.

Swipe with one finger to move the center of the map.

Use two fingers to zoom in and out.

48

5

6

4

2

1

7

3

Cameras

Use the camera app to take pictures and videos, such as for inspection reports.

1 Take a photo.

2 Start or stop recording a video.

3 Adjust camera settings.

4 Adjust image settings.

5 Panoramic photo mode.

6 Gallery.

7 Turn on/off HDR capture for photos.

6. Cameras


4

3

1

2

7. DriverConnect

DriverConnect

The DriverConnect app provides a fully-compliant electronic logbook solution. DriverConnect lets you track and log Hours of Services, Driver-

Vehicle Inspection Reports, Fuel purchases, and more. Reports can be generated for roadside inspections.

The DriverConnect app connects to a Rand McNally Electronic Logging

Device (ELD) over a Bluetooth connection. The app automatically syncs driving data from the ELD with the Rand McNally DriverConnect portal via a Wi-Fi or cellular transmission.

Visit randmcnally.com/category/e-logs for up-to-date information on compatible ELDs.

Sign Up or Log In

To use DriverConnect, you must log in with an existing account or create a new account. If you are part of a fleet, your Fleet Manager will provide login information for you.

Visit driverconnect.randmcnally.com

to access the DriverConnect portal.



For more information

• Rand McNally Website randmcnally.com/trucking

• Support randmcnally.com/support

• GPS accessories store.randmcnally.com

• Facebook facebook.com/randtrucking

8. More Information

51


Trademarks

Rand McNally, the Rand McNally logo, the globe logo, and IntelliRoute are registered trademarks and TND is a trademark of RM Acquisition LLC, d/b/a Rand McNally.

Travel center data provided by DC Book Co.

TruckDown is a registered trademark of TruckDown Info International, Inc.

Wi-Fi is a registered trademark of the Wi-Fi Alliance.

Weather data provided by VAISALA.

Fuel prices provided by OPIS.

Traffic information provided by INRIX, Inc.

© 2022 Rand McNally. © 2022 HERE. All rights reserved.

Rand McNally follows a continuous improvement process and reserves the right to provide enhancements that may not be reflected in the pictures and specifications in this manual.

The information contained herein may be changed at any time without prior notification. Neither this manual nor any parts thereof may be reproduced for any purpose whatsoever without the express written consent of Rand McNally, Inc., nor may it be transmitted in any form either electronically or mechanically, including photocopying, and recording. All technical specifications, drawings, etc. are subject to copyright law.

52

No results