advertisement
1. Package Contents
Thank you for purchasing PLANET 1-Port 10/100/1000BASE-T to 2-Port 100/1000BASE-X Media Converter, GT-1205A.
Open the box of the GT-1205A and carefully unpack it. The box should contain the following items:
Gigabit Media Converter x 1 User's Manual x 1
AC-DC Adapter (Output: 5V DC, 2A max.) x 1
If any item is missing or damaged, please consult the dealer from whom you purchased your GT-1205A.
Note
The GT-1205A comes with one vacant SFP module slot. The mini GBIC SFP module is not bundled with in the package.
- 1 -
Compact in size, easy installation
Co-works with PLANET’s 10”/19” Media Converter Chassis
(MC-700/MC-1500/MC-1500R/MC-1500R48)
Wall mounting and DIN-rail installation supported
Standard
Complies with IEEE 802.3 10BASE-T
Complies with IEEE 802.3u 100BASE-TX/100BASE-FX
Complies with IEEE 802.3ab 1000BASE-T
Complies with IEEE 802.3z 1000BASE-SX/LX
IEEE 802.3x full-duplex flow control; back pressure for half duplex to prevent packet loss
3. Hardware Introduction
3.1 Front Panel and LED Indicators
GT-1205A Front Panel
The GT-1205A consists of two 100/1000BASE-X SFP slots and one auto-sensing 10/100/1000Mbps Ethernet RJ45 port. Figure
1 shows the front panel of the GT-1205A.
3
2
1
1 2
PWR
GT-1205A
1000
Figure 1: GT-1205A Front Panel
- 3 -
LNK/
ACT
3.2 Rear Panel
The rear panel of the GT-1205A has one DC jack, which accepts an input power of 5V DC with 2A. The brand-new DIP switch designed for 1000BASE-X SFP module or 100BASE-FX
SFP module supports on dual SFP slots. The default DIP switch mode is 1000BASE-X.
5V DC
SFP Speed
1000BASE-X 100BASE-FX
Figure 2: GT-1205A Rear Panel
Caution
Please power off and power on the GT-1205A after adjusting the DIP switch setting.
Power Information
The center pin diameter of the GT-1205A’s power jack is
2.5mm and the power jack allows an input power of 5V DC.
It conforms to the bundled AC-DC adapter and PLANET’s media chassis. Should you have any issue about the power connection, please contact your local sales representative.
Please keep the AC-DC adapter as a spare part when your
GT-1205A is installed to a Media Chassis.
- 5 -
4. Redundancy Overview
The GT-1205A provides rapid fiber redundancy of link for highly critical Ethernet applications. The redundant mode supports auto-recover function. If the destination port of a packet is linked down, it will forward the packet to the other port of the backup pair. The following figure shows the redundant function.
Figure 4: Redundancy Behavior Topology
Link status auto detection and redundancy of dual ports with the same connector type.
Only the Primary Port is active at a time, the Backup Port is blocked.
- 7 -
2. Product Features
Interface
Dual 100/1000BASE-X SFP fiber-optic slots
One 10/100/1000BASE-T copper port with auto MDI/MDIX function
Auto-negotiation for 10/100/1000BASE-T; half-duplex or fullduplex for 10Mbps and 100Mbps, full-duplex for 1000Mbps
Supports maximum frame size up to 10K jumbo packet size
IEEE 802.1Q tagged VLAN transparent, multicast passthrough
Redundancy
Link status auto-detection and redundancy of dual ports with the same connector type
Allows only the Primary Port or the Backup Port to activate at a time
- When Primary Port link failure occurs, the traffic swaps to Backup Port automatically
- Once the Primary Port link regains, the traffic swaps from the Backup Port to the Primary Port
- Redundant hardware fiber port
Mechanical
External 5V DC, 2.5A power supply
LED indicators for easy network diagnostics
DIP switch for 100FX or 1000X SFP module supports on dual SFP slots
DIP switch for 3-port operation in Gigabit switch mode or redundant mode
- 2 -
GT-1205A LED Indication
System
LED Color Function
PWR Green Lit when +5V DC power is detected.
100/1000BASE-X SFP Slots
LED Color
Lit
Function
Indicates that the fiber optical port is linked up.
1 Green
Off
Lit
Indicates that the fiber optical port is linked down.
Indicates that the fiber optical port is linked up.
2 Green
Off
Indicates that the fiber optical port is linked down.
10/100/1000BASE-T Port
LED Color
Lit
Function
Indicates that the copper port is linked up.
LNK/
ACT
Orange
Off
1000 Green
Lit
Off
Indicates that the copper port is linked down.
Indicates that the copper port is operating at 1000Mbps .
Indicates that the copper port is linked down or 10/100Mbps .
- 4 -
2.5mm
DC Receptacle 2.5mm
+5V for each slot
DC receptacle is 2.5mm wide that conforms to the GT-
1205A’s 2.5mm DC jack's central post. Do not install any improper unit.
The device is a power-required device, meaning it will not work till it is powered. If your networks should be active all the time, please consider using UPS (uninterrupted power supply) for your device. It will prevent you from network data loss or network downtime.
In some areas, installing a surge suppression device may also help to protect the GT-1205A from being damaged by unregulated surge or current.
3.3 Side View
The side panel of the GT-1205A has a DIP switch for setting to the 3-port switch mode or the 2-port redundant mode. When
“ON” , it is in the 2-port redundant mode. And when “OFF” , it is in the 3-port switch mode.
3-Port Switch OFF
2-Port Redundant ON
OFF
Redundant
ON
Figure 3: GT-1205A Side Panel
- 6 -
When the Primary Port’s link failure occurs, the traffic will swap to Backup Port automatically.
Once the link of the Primary Port is back, the traffic will swap from Backup Port to Primary Port.
5. Installing The Converter
The GT-1205A can be connected over fiber optic cabling at a distance extended from 550 meters to 2km (multi-mode fiber) to 10/20/40/60/80/120 kilometers (single-mode fiber or WDM fiber), using the 100/1000BASE-X SFP modules. The SFP modules are hot-pluggable and hot-swappable. You can plug in and out the SFP modules to and from any SFP port without having to power down the GT-1205A.
To install GT1205A, please follow these steps to install the
GT-1205A:
Ethernet Installation
Step 1: Turn off the power of the device/station in a network to which the GT-1205A will be attached.
Step 2: Ensure that there is no activity in the network.
Step 3: Slide in the 100/1000BASE-X SFP module. Make sure both sides of the SFP modules are with the same media type, for example, 100BASE-FX/2km multimode to 100BASE-FX/2km multi-mode, 1000BASE-
SX/550m multi-mode to 1000BASE-SX/550m multi-mode or 1000BASE-LX/10km single mode to
1000BASE-LX/10km single mode.
- 8 -
100/1000BASE-X
SFP Module
10/100/1000BASE-T
UTP
5V DC power
100/1000BASE-X
LC Fiber
100/1000BASE-X
LC Fiber
Figure 5: GT-1205A Gigabit Media Converter Standalone Installation
Step 4: Connect the fiber cable. Attach the duplex LC connector on the network cable to the SFP modules.
Step 5: Attach fiber cable from the GT-1205A to the fiber network. TX, RX must be paired at both ends.
Step 6: Connect the 5V DC power adapter to the GT-1205A and verify that the Power LED lights up.
Step 7: Turn on the power of the device/station; the LINK
LED should light up when all cables are well attached.
Note
1. It is recommended to use PLANET MFB/MGB series SFP modules for the GT-1205A. If you insert an SFP module that is not supported, the
GT-1205A will not recognize it. Please check appendix or go visit our Web site for detailed specification. http://www.planet.com.tw
check both the wires and transmitter before powering on the converter.
- 9 -
6 Cable Connection Parameter
The wiring details are shown below:
Duplex
Twisted Pair
Connection Limitation (max.)
Half/Full
Node to Node
Node to Switch/Hub
100 meters
Fiber Optic Cables:
Standard
(Wavelength)
Fiber Type
& Cable
Specifications
100BASE-FX
(1310nm)
1000BASE-SX
(850nm)
Multi-mode
50/125μm or
62.5/125μm
Single-mode 9/125μm
1000BASE-LX
(1310nm)
7. Product Specifications
Model GT-1205A
Interface Specifications
Hardware Version 4
Ports
Copper
Fiber
1 x 10/100/1000BASE-T port
2 x 100/1000BASE-X SFP slots
- 11 -
Note
3. To remove the SFP module, please remove the fiber connectors in advance and push the belt or latch of the module. Pull out the module with force may damage the module and the GT-
1205A.
Media Converter Chassis Installation
To install the GT-1205A in a 10-inch or 19-inch standard rack, follow the instructions described below.
Step 1: Place your GT-1205A on a hard flat surface, with the front panel positioned towards your front side.
Step 2: Carefully slide in the module until it is fully and firmly fitted into the slot of the chassis; the Power LED of the GT-1205A will turn ON.
Figure 6: Inserting GT-1205A into an available slot
Caution
1. Never push the converter into the slot with force; it could damage the chassis .
2. The Media Converter Chassis supports hot-swap; there is no need to turn off the whole chassis before sliding in the new converter.
- 10 -
Twistedpair
10BASE-T: 2-pair UTP Cat 3, 4, 5, up to
100 meters
100BASE-TX: 2-pair UTP Cat 5, 5e up to
100 meters
1000BASE-T: 4-pair UTP Cat 5e, 6 up to
100 meters
Cable
Fiberoptic
Cable
1000BASE-SX:
50/125μm or 62.5/125μm multi-mode fiber cable, from 220 and 550 meters to 2km.
1000BASE-LX:
9/125μm single-mode cable, with distance of 10/20/40/80/120km (vary on SFP module)
100BASE-FX:
50/125μm or 62.5/125μm multi-mode fiber cable, up to 2km (vary on SFP module)
9/125μm single-mode cable, with distance for 20/40/60m (vary on SFP module)
Hardware Specifications
Switch
Architecture
Store and Forward
Flow Control
Back pressure for half duplex.
IEEE 802.3x pause frame for full duplex
6Gbps Fabric
Throughput
(packet per second)
4.4Mpps
Maximum Packet
Size
10K bytes
- 12 -
LED Display
Dimensions
(W x D x H)
Weight
Power
Requirement
Power
Consumption
Environment
Operating environment
Storage environment
Operating
Humidity
System: One Power LED (Green)
Fiber Port : Two LNK/ACT LEDs (Green)
TP Port : One Speed LED (Green),
One LNK/ACT LED (Orange)
94 x 70 x 26mm
180g (device only)
5V DC, 2A max.
2.8 watts/9.5BTU per hour (max.)
0 ~ 50 degrees C
-10 ~ 70 degrees C
5 ~ 95%, relative humidity
(non-condensing)
Standard Conformance
EMI Safety FCC Class B, CE
Standard
Compliance
IEEE 802.3
IEEE 802.3u
IEEE 802.3ab
IEEE 802.3z
IEEE 802.3x
10BASE-T
100BASE-TX/100BASE-FX
1000BASE-T
1000BASE-SX/LX
Flow Control
- 13 -
EC Declaration of Conformity
For the following equipment:
*Type of Product : 10/100/1000BASE-T to Dual 1000BASE-X SFP Media Converter
*Model Number : GT-1205A
* Produced by:
Manufacturer‘s Name : Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan R.O.C.
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on 2014/30/EU.
For the evaluation regarding the EMC, the following standards were applied:
EN 55032
EN 61000-3-2
EN 61000-3-3
EN 55024
(2015)
(2014)
(2013)
(2010 + A1: 2015)
Responsible for marking this declaration if the:
Manufacturer Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan R.O.C.
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Director
Taiwan
Place
Aug. 23, 2019
Date Legal Signature
PLANET TECHNOLOGY CORPORATION e-mail: [email protected] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528
advertisement
Related manuals
advertisement