advertisement
1. Package Contents
Thank you for purchasing PLANET IEEE 802.3at High
Power over Ethernet Injector, POE-163/POE-164.
Model LAN Port Speed PoE Standard PoE Budget
POE-163 10/100/1000Mbps 802.3at /
POE-164 10/100Mbps 802.3af
30 watts
“802.3at PoE Injector” used in this user’s manual refers to the POE-163/POE-164.
Unpack the box of the IEEE 802.3at High Power over Ethernet Injector carefully and the box should contain the following items:
The IEEE 802.3at High Power over Ethernet
Injector x 1
User’s Manual x 1
AC Power Cord x 1
If any of these are missing or damaged, please contact your dealer immediately. If possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.
IEEE 802.3af Power over Ethernet (802.3at
Type 1)
IEEE 802.3at Power over Ethernet (802.3at
Type 2)
FCC Part 15 Class B, CE
Note
PSE (Power Sourcing Equipment) is a device (switch, or hub for instance) that will provide power in a PoE setup.
The maximum continuous output power allowed for each IEEE 802.3at/IEEE
802.3af device is 30W/15.4W.
PDs (Powered Devices) like IP phones, network cameras and wireless access points, etc. are PoE-enabled terminals and thus they are power sourcing equipment (PSE).
- 3 -
Power Requirements 100-240V AC, 50/60Hz, 0.75A
Power Consumption
Number of devices that can be powered
30 Watts max.
1
Operating Temperature 0 ~ 50 degrees C
Storage Temperature -10 ~ 70 degrees C
Operating Humidity
Storage Humidity
5 ~ 95%, relative humidity, non-condensing
5 ~ 95%, relative humidity, non-condensing
Power over Ethernet
PoE Standard
IEEE 802.3at Power over
Ethernet Plus / Mid-span PSE
PoE Power Output DC 50-54V / 30 watts
PoE Power Supply Type Mid-span
Power Pin Assignment 4/5(+), 7/8(-)
Standards Conformance
Standards Compliance
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast
Ethernet
IEEE 802.3ab 1000BASE-T
Gigabit Ethernet (POE-163 only)
IEEE 802.3af Power over Ethernet
(802.3at Type 1)
IEEE 802.3at Power over
Ethernet (802.3at Type 2)
Regulatory Compliance FCC Part 15 Class B, CE
- 5 -
5. Hardware Installation
The following section describes the hardware features of the 802.3at PoE Injector. Before connecting any network device to the 802.3at PoE Injector, read this chapter carefully.
This POE-163 provides three different running speeds – 10Mbps / 100Mbps / 1000Mbps and the
POE-164 provides two different running speeds
– 10Mbps / 100Mbps in the same device for automatically distinguishes the speed of incoming connection. Please refer to following sections for detailed information about the IEEE 802.3at Power over Ethernet Injector.
5-1 Before Installation
Before your installation, it is recommended to check your network environment. If there is any IEEE
802.3at devices that need higher power to power on and work normally, the 802.3at PoE Injector can provide you with power for this Ethernet device easily. The 802.3at PoE Injector is equipped with an
AC power cord with 100-240V AC input and injects
DC 50-54V power into the pin of the twisted-pair cable (pair 4, 5 [+] and pair 7, 8 [-] ).
If a power socket for the AC-DC adapter of your non
IEEE 802.3at networked device is not available, the
802.3at PoE Injector and POE-162S can provide you with DC power for this Ethernet device easily.
- 7 - 1 -
2. Product Features
Interface
2-port RJ45 interfaces
1-port Data + Power output
1-port Data input
1 AC 100-240V input power socket
Power over Ethernet
High Power over Ethernet Mid-span PSE
IEEE 802.3at PoE Plus compliant
Backward compatible with IEEE 802.3af PD device
Supports PoE Power up to 30 watts for PoE port
Auto-detects PoE IEEE 802.3at / 802.3af equipment and devices for preventing damage from incorrect installation
Remote power feeding up to 100m
Hardware
Plastic case
LED indicators for Power LED and Active LED
(PoE ready-in-use)
Standard Compliance
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab 1000BASE-T (POE-163 only)
- 2 -
3. Product Specifications
Product
Hardware Specifications
“Data” Input
Port
Interface
“PoE (Data
+ Power)”
Output Port
POE-163
1 x RJ45 STP
1 x RJ45 STP
POE-164
AC Input
Power Socket 1
LED Indicator
Network Cable
System: Power x 1 (Green)
PoE Port: Active, PoE ready / In
Use x 1 (Green)
10BASE-T: 2-pair UTP Cat. 3, 4,
5, up to 100m (328ft)
100BASE-TX: 2-pair UTP Cat. 3,
4, 5, up to 100m (328ft)
1000BASE-T: 2-pair UTP Cat. 5,
5e, 6 up to 100m (328ft)
(POE-163 only)
EIA/TIA-568 100-ohm STP
(100m)
10/100/1000Mbps 10/100Mbps Data Rate
Dimensions
(W x D x H)
Weight
Unit Output Voltage
115 x 62.5 x 31 mm
177g
DC 50-54V, 0.6A
- 4 -
4. Product Outlook
Figure 1: shows an overview of the 802.3at PoE
Injector.
Top Panel
Top Panel
Front Panel
Front Panel
Rear Panel
Rear Panel
Bottom
Bottom
Figure 1: POE-163 / POE-164 Outlook
LED Indicators
LED Color
POWER Green
ACTIVE Green
Function
Lights to indicate that the 802.3at PoE
Injector has power.
Lights off to indicate the port is not providing 50-54V in-line power.
Lights to indicate the port is providing
50-54V in-line power.
- 6 -
Note
The 802.3at PoE Injector and POE-162S can be installed in pair. However, the use of third-party device is allowed if the device complies with IEEE 802.3at
Power over Ethernet.
The 802.3at PoE Injector Installation
1. Connect the AC power cord to the “AC slot” of the 802.3at PoE Injector; the “POWER” LED will be steadily on.
2. Connect a standard network cable from a switch / workstation to the “LAN” port of the 802.3at PoE
Injector.
3. And connect the Injector to a remote device like a
PoE PTZ IP camera over the UTP cable.
** The 802.3at PoE Injector can directly connect with any IEEE 802.3at / 802.3af end-nodes, such as PTZ IP and speed dome cameras, color touchscreen Voice over IP (VoIP) telephones, multichannel wireless LAN access points, etc. The installation is shown in Figure 2 below.
- 8 -
100 meters
Switch
Data
AC
Power
802.3at PoE Injector
Data
PoE
Power
PoE
AC
PoE PTZ
IP Camera
1000BASE-T UTP
1000BASE-T UTP with PoE
Power Line (AC)
Figure 2: Connection to IEEE 802.3at / 802.3af Devices
When the ACTIVE LED blinks slowly, it indicates the port is not providing 50-54V DC in-line power. Once the 802.3at PoE Injector detects the existence of an IEEE 802.3at / 802.3af device, the ACTIVE LED indicator will be steadily on to show it is providing power.
Note
1. Since the 802.3at PoE Injector PoE port supports 50-54V DC PoE power output, please check and assure the powered device’s (PD) acceptable DC power range is 50-54V DC. Otherwise, it will damage the PD.
2. If the connected device is not fully complying with IEEE 802.3at /
802.3af Power over Ethernet or inline power device, the LED indicator of the 802.3at PoE Injector will not be steadily on.
- 9 -
Note
1. Owing to IEEE 802.3at / 802.3af
Power over Ethernet standards, the
802.3at PoE Injector will not inject power over the cable if not connected to IEEE 802.3at / 802.3af devices.
2. Please ensure the POE-162S output voltage is correct before applying power to remote devices.
The 802.3at PoE Injector and POE-E201 IEEE
802.3at PoE Extender Installation
1. Connect the AC power cord to the “AC slot” of the 802.3at PoE Injector; the “POWER” LED will be steadily on.
Connect a standard network cable from the
“POE” port of the 802.3at PoE Injector to the
“IN” port of the POE-E201.
3. The 802.3at PoE Injector delivers both Ethernet
Data and PoE power over UTP cable to the
POE-E201 and the “ACTIVE” LED of the 802.3at
PoE Injector and the “PoE IN” LED of the
POE-E201 will continue to be lit.
4. Connect an additional standard network cable that will be used to connect from the “OUT” port of the POE-E201 to a remote Powered Device
(PD).
5. The "OUT" port of the power injector transmits
DC voltage over the standard network cable and transfers data and power simultaneously between the 802.3at PoE Injector and the PD.
- 11 -
The 802.3at PoE Injector and POE-162S, the
IEEE 802.3at Injector Splitter Installation
1. Connect the AC power cord to “AC slot” of the
802.3at PoE Injector; the “POWER” LED will be steadily on.
Connect a standard network cable from the
“POE” port of the 802.3at PoE Injector to the
“PoE In” port of the POE-162S. The “ACTIVE”
LED of the 802.3at PoE Injector and PoE-in-use
LED of the POE-162S will continue to be lit.
3. Connect a standard network cable from a switch / workstation to the “LAN” port of the 802.3at PoE
Injector.
4. Connect the UTP cable in the package from the
“Ethernet” port of the POE-162S to the RJ45 port of a remote device.
5. Adjust the proper DC power output and connect the DC plug from the “DC OUT” of the POE-162S to a remote device.
6. Power on the remote device and its power LED indicator will remain on.
100 meters
Switch
Data Data
AC
Power
802.3at PoE Injector
PoE
Power
POE-162S
802.3at PoE
Splitter
Non-PoE PTZ
IP Camera
Data
DC
Power
Power 12V/24V
AC
DC
Power Line (AC)
Power Line (DC)
1000BASE-T UTP
1000BASE-T UTP with PoE
PoE
Figure 3: Connection architecture over 802.3at PoE
Injector / POE-162S
- 10 -
6. Once the POE-E201 detects the existence of an
IEEE 802.3at / 802.3af device, the “PoE OUT”
LED indicator will be steadily on to show it is providing power.
200 meters
Data
Power
Data + Power
PoE
100 meters
802.3at PoE Injector 802.3at
PoE Extender
Data + Power
PoE
100 meters
AC
PoE
PoE IP Camera
Power Line (AC)
1000BASE-T UTP
1000BASE-T UTP with PoE
Figure 4: Connection architecture over 802.3at PoE
Injector / POE-E201
Note
1. If the connected device is not fully complying with IEEE 802.3at /
802.3af standards or in-line power device, the PoE OUT LED indicator of the POE-E201 will not be steadily on.
2. Owing to IEEE 802.3at / 802.3af standards, the POE-E201 will not inject power over the cable if a standard IEEE 802.3at / 802.3af device is not connected.
- 12 -
Customer Support
Thank you for purchasing PLANET products. You can browse our online FAQ resource at the PLANET
Web site first to check if it could solve you issue. If you need more support information, please contact
PLANET switch support team.
PLANET online FAQ : http://www.planet.com.tw/en/support/faq.php?type=2
Switch support team mail address : [email protected]
Copyright © PLANET Technology Corp. 2015.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
- 13 -
EC Declaration of Conformity
For the following equipment:
*Type of Product : Single-Port 10/100/1000Mbps IEEE 802.3at PoE+ Injector (30Watts)
Single-Port 10/100Mbps IEEE 802.3at PoE+ Injector (30Watts)
*Model Number : POE-163, POE-164
* Produced by:
Manufacturer‘s Name : Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan (R.O.C.). is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on (2004/108/EC).
For the evaluation regarding the EMC, the following standards were applied:
EN55022
EN 61000-3-2
EN 61000-3-3
EN55024
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
(2006 + A1:2007 + A2:2010)
(2006 + A1:2009 + A2:2009)
(2008)
(2010)
(2008)
(2006+A1: 2007 + A2:2010)
(2004 + A1:2010)
(2005)
(200
8
)
(2009)
(2004)
Responsible for marking this declaration if the:
Manufacturer Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)
Person responsible for making this declaration
Name, Surname
Position / Title :
Kent Kang
Product Manager
Taiwan
Place
29 th March, 2013
Date Legal Signature
PLANET TECHNOLOGY CORPORATION e-mail: [email protected] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528
advertisement
Related manuals
advertisement