AutoSeal

®

FD 2006/FD 2036

FE 2006/FE 2036

FI / FJ Series

8/2018

OPERATOR MANUAL

FIRST EDITION

TABLE OF CONTENTS

SUBJECT

DESCRIPTION

SPECIFICATIONS

UNPACKING

Components

Optional Conveyor Components

CONTROL PANELS

SETUP

Installing Fold Plates & Power Cord

Installing Optional Conveyor

OPERATION

DETERMING FOLD TYPE

SETTING CUSTOM FOLDS

OPERATOR MAINTENANCE

ERROR SCREENS

TROUBLE-SHOOTING

PAGE

3

4 - 5

4

5

6

8

9

10-11

12

13

2

2

1

1

2

DESCRIPTION

Paper Side Guides

Feed Table

Top Cover

Control Panel

Lower Fold Plate

Upper Fold Plate

Operator Side Cover

Optional 18” Conveyor

FUNCTION

The 2006 / 2036 pressure sealer folds and seals pressure sensitive forms with pre-applied glue lines into mail ready pieces. Numerous folds using several different paper sizes can be processed to meet your needs. For configurations and paper sizes see specifications.

SPECIFICATIONS

Speed 2006 / 2036: Up to 8,000 / 11,000 forms per hour, depending on fold type

Hopper Capacity 2006 / 2036: Up to 250 / 350 sheets of 24# (90gsm) pre-glued forms

Paper size:

Pre-Marked fold types:

Min: 3.5” X 5” (88.9 W x 127 L mm)

Max: 12.25” X 18” (311 W x 457 L mm)

Letter , Zig-Zag , Half

Pre-Marked Paper Sizes:

Dimensions:

Dimensions w/ Conveyor:

Weight:

Power:

Safety Certifications:

FD Model: 11”, 14”

FE Model: A4

25.75” L x 16.5” W x 14.25” H (65 L x 42 W x 36 H cm)

46” L x 22” W x 14.25” H (117 L x 56 W x 36 H cm)

90 lbs (40 kg)

FD Model: 120 volts A.C., 50/60 Hz, 2.5 amps.

FE Model: 220 volts A.C., 50/60 Hz, 2.5 amps

UL Approved & CE Applied for

1

UNPACKING

1.

Check package for shipping damage. If there is shipping damage, do not discard the box.

2.

Remove the machine and packed components from the box. Upper and lower fold plates, jam Clearing Handle

(located under the top cover) and power cord.

CAUTION: Two people must lift the machine from the box.

3.

Place the Pressure Sealer on a solid stand.

COMPONENTS

1

3

4

1

2

3

2006/2036

Catch Tray

Upper Fold Plate

OPTIONAL CONVEYOR COMPONENTS

2

4

5

6

5

Power Cord

Lower Fold Plate

Jam Clearing Tool (ships installed)

6

5

6

1

1

2

3

Conveyor

Extension Tray

Mounting Shoulder Bolts

2 3 4

4 Extension Tray Mounting Screws

5 Power Cord

6 Out-feed Wheel Assembly

2

CONTROL PANELS

Counter

Counter reset

Start icon

NAME

Start Icon

Stop Icon

Jog Icon

Reset Icon

Counter

Jog icon

FUNCTION

Press to start

Press to stop / Press

Allows one form to feed at a time. Used to set fold plates accurately

Resets the counter

Shows the number of documents processed

Stop icon

Optional Conveyor Controls

Runout button Power switch

NAME

Runout Button

Power Switch

FUNCTION

Push to advance forms on the conveyor.

Turns the power on. When the power is on the green light is illuminated. The conveyor advances using a photo-eye.

3

SETUP

Installing Upper and Lower Fold Plates, and

Power Cord

1.

Be sure the plate sets firmly on the locating pins

(Fig 1a & 1b). Lift the top cover and slide the upper fold plate under the top cover pins onto the fold plate pins. Push down on the fold plate to lock it in position.

Upper Fold Plate Pins Top Cover Pins

Fig. 1a

2. Lift the In-feed extension tray and lock it into place.

Then slide the bottom fold plate up and in until it meets the rear locating pins then push down to set in place.

Lower Fold Plate Pins

Locating Pins

In-feed extension tray

3.

Plug the power cord into the left receptacle on the back side of the machine (Fig 1c).

Fig. 1b

Locating Pins

4

Fig. 1c

Installing Optional Conveyor

1.

Assemble the conveyor. Attach the extension tray to the end of the conveyor using the three extension tray screws (Fig 2a).

2. Insert power cord to receptacle on the underside of the conveyor (Fig 2b)

Fig. 2a

Mounting Screws

Fig. 2b

3.

Remove catch tray and install the mounting shoulder screws into the two screw holes (Fig 2c).

4.

Open the top cover of the sealer and remove the top fold plate. Then slide the conveyor into position aligning the keyholes on the back of the conveyor with the shoulder screws, slide in and down to lock into position.

5.

Install the out-feed nip wheels into the two holes located at the out-feed of the sealer (Fig 2d). Insert the side of the rod with the spring first, push in and then insert the other side. Reinstall the top fold plate and close the top cover.

Fig. 2c

Fig. 2d

6.

Plug the conveyor into the right receptacle on the back of the pressure sealer (Fig 3).

5

Fig. 3

Spring

Shoulder screws

OPERATION

1.

Place power switch in the “ON” position.

2.

After determining the fold type (see pg 6

“Determining Fold Type”) set the Upper and Lower fold plates.

To set the fold stop position, squeeze the fold stop lever and slide it to the desired location on the upper and lower fold plates (Fig 4). Align the pointed part of the stop plate with the desired marks on the decal and release the lever. Fine adjustments can be made with the adjustment knob at the end of the plate (Fig 5).

NOTE: When setting a “Half” fold, remove the bottom fold plate, turn it 180 degrees and insert with the fold deflector leading (Fig 6). The plate must be firmly reinstalled on the locating pins.

Fig. 4

Fig. 5

Fig. 6 Fold Deflector

5a. Set the catch tray (See step 5b if using a conveyor).

Slide the catch tray in or out to align the appropriate fold/form setting on the “Fold/form size decal” with the alignment decal located on the non-operator side frame

(Fig 7a).

5b. Set the conveyor out feed wheels. Align the center of the out-feed stacker wheels with the appropriate fold/ form setting on the “Fold/form size decal” (Fig 7b).

Fig. 7a Alignment Decal Fold/Form Size Decal

6

Fig. 7b

Fold/Form Size Decal

5.

Set the paper side guides for the forms being used and lock in position (Fig 8a).

Place a form between the side guides. Adjust the side guides by loosening knobs on top, then sliding them toward or away from each other so that the form is snug but still lies flat .

Leave equal spacing between the guides and side frame on both sides to help ensure that the forms feed squarely into the pressure sealer (Fig 8b).

Fig. 8a

Paper Side Guides

Fig. 8b

Equal spacing between side frame and guides on both sides

6.

Lift the in-feed tray lever, then neatly stack paper on the in-feed tray under the feed tires and release the tray lever (Fig 9).

7.

Press the “ ” icon on the control panel to test the folds. Adjust as needed.

8.

If the fold is skewed use the skew adjustment knob to make corrections (Fig.10).

9.

When you’re satisfied with the test folds, press the

“ ” icon to operate the machine.

Fig. 9

In-feed Tray Lever

7

Fig. 10 Skew Adjuster

DETERMINING FOLD TYPE

Two Standard Folds 11” “Z” & 11” “C”

Leading glue edge

Glue

11” “Z” Fold

Glue

11” “Z” Fold

Leading glue edge

Glue

Glue

11” “C” Fold

11” “C” Fold

8

SETTING CUSTOM FOLDS

Example 1: Uneven “Z”

1.

Measure the length of panel “A”

2.

Adjust the upper fold plate so that the fold stop lines up with the measurements of the panel “A” i.e. if panel “A” is 5 1/4” long slide the stop plate up or down so that it lines up with the 5 1/4” mark on the fold plate.

3.

Measure the length of panel “B”

4.

Adjust the lower fold plate so that the stop plate lines up with the measurement of panel “B”

5.

Load forms and press test. If folds are too long or too short adjust accordingly.

Example 2: Uneven “C”

1.

Measure the length of panel “A” & “B”

2.

Adjust the upper fold plate so that the fold stop lines up with the measurements of panel “A” & “B”. i.e. if panel

“A” & “B” are 10 1/2” long slide the stop plate up or down so that it lines up with the 10 1/2” mark on the fold plate.

3.

Measure the length of panel “B”

4.

Adjust the lower fold plate so that the stop plate lines up with the measurement of panel “B

5.

Load forms and press test. If folds are too long or too short adjust accordingly.

Panel A

Panel B

Panel A

Panel B

9

OPERATOR MAINTENANCE

1. I t is recommended to let forms cool for one-half hour, from the laser printer, before folding. This allows toner to set on the forms and static electricity to discharge. A 402 Series Jogger is recommended for best results. The Jogger squares the forms and dissipates heat and static electricity created by laser printers.

2. If toner builds up on the metal sealer rollers clean them with a lint-free cloth dampened sparingly with a mild household cleaner.

3. Clean in-feed tires and fold rollers with dealer recommended roller cleaner & rejuvenator to remove paper dust and toner. A Cleaner Kit is available from your dealer. A damp cloth with water is the best alternative.

CAUTION: Do not use any chemicals other than the roller cleaner & rejuvenator or water.

METAL SEAL ROLLERS CLEANING PROCEDURE:

1. Make sure machine is turned off and unplugged. All folders have four (4) rubber rollers (Fig. 11).

2. Open the top cover and remove the upper fold plate to access the seal rollers.

3. Using a mild household cleaner, spray a new cotton cloth until the cloth is saturated. Wipe the wet cloth in a back and forth motion and rotate the rollers by hand making sure to clean the entire surface of the seal rollers. Next use a dry cloth and wipe off excess toner.

The cloth should be covered with black toner surplus from cleaning the rollers.

4. Run 10-15 sheets of blank copy paper through the folder/sealer to ensure all cleaner has been removed from the fold rollers. Running blank sheets will remove any excess residue of cleaner on the rollers.

IN-FEED TIRES AND FOLD ROLLERS

CLEANING PROCEDURE:

1. Make sure machine is turned off and unplugged. The sealers have three (3) feed tires and four (4) rubber rollers (Fig. 12a & 12b).

2. Open the top covers and remove the upper and lower fold plates to access the tires and rollers.

3. Using roller cleaner, spray a new cotton cloth until the cloth is saturated. Wipe the wet cloth in a back and forth motion and rotate the tires / rollers by hand making sure to clean the entire surface of the feed tire

/ fold rollers. Next use a dry cloth and wipe off excess toner. The cloth should be covered with black toner surplus from cleaning the tires / rollers.

Fig. 11

Fig. 12a

Seal Rollers

Feed Tires

4. Run 10-15 sheets of blank copy paper through the folder/sealer to ensure all cleaner has been removed from the fold rollers. Running blank sheets will remove any excess residue of cleaner on the rollers.

Fig. 12b

Fold Rollers

10

CLEARING PAPER JAMS:

WARNING: Turn off machine and unplug cord from its receptacle

1. If a jam occurs between the metal rollers remove any remaining forms from the hopper. Open the top cover and remove the upper fold plate. Remove the jam clearing handle (located under the upper fold table) apply the handle to the upper metal roller (Fig13) and turn clockwise until the paper jam is clear. NOTE: Do not turn the roller counter-clockwise to force the forms to exit: rollers may be damaged. Remove the damaged form, return tool to holder and reinstall upper fold plate.

2. Reinstall cover and press the black reset button

(Fig14).

Fig. 13

Fig. 14

Reset Button

11

ERROR SCREENS

Paper Mis-Feed / Paper Jam

FD 342 Touch Screen -Error Screens

Paper Jam Paper misfeed

A mis-feed has occurred. Reset the stack of paper in the in-feed and press the “ “ icon to resume operation. A Paper jam has occurred in one of the areas indicated. Turn the folder to the off position and unat any time. If the jam is not cleared the error screen will plug. Check the area indicated for paper and remove.

Replace the fold plates and plug the folder in and the

Cover Open

Paper Out

Error screen will appear with arrow pointing to empty infeed tray. Press return arrow to go back to the home screen.

* Paper Out screen will come on if start is pressed and the is no paper in the feed tray.

Error screen will apear with arrow pointing to open cover with indicator to close cover. Press return arrow to go back to the main screen.

Cover Open

FD 342 Touch Screen -Error Screens

Paper Jam Paper misfeed

FD 342 Touch Screen -Error Screens

Paper Jam Paper misfeed

There is no paper in the in-feed. Reload paper and press the “ “ icon to resume operation.

Error screen appears with arrows pointing to possible areas to check. Press the return arrow to go back to home screen at any time. If the jam is not cleared the error screen will appear again after pressing start or 1x.

Error screen will appear with arrow pointing to infeed.

Press return arrow to go back to the home screen.

Error screen appears with arrows pointing to possible areas to check. Press the return arrow to go back to home screen at any time. If the jam is not cleared the error screen will appear again after pressing start or 1x.

The top cover is open. Close the top cover and press the “ “ icon to resume operation.

Error screen will appear with arrow pointing to infeed.

Press return arrow to go back to the home screen.

Paper Out Cover Open Paper Out Cover Open

Error screen will appear with arrow pointing to empty infeed tray. Press return arrow to go back to the home screen.

* Paper Out screen will come on if start is pressed and the is no paper in the feed tray.

Error screen will apear with arrow pointing to open cover with indicator to close cover. Press return arrow to go back to the main screen.

Error screen will appear with arrow pointing to empty infeed tray. Press return arrow to go back to the home screen.

12

* Paper Out screen will come on if start is pressed and the is no paper in the feed tray.

Error screen will apear with arrow pointing to open cover with indicator to close cover. Press return arrow to go back to the main screen.

TROUBLESHOOTING

TROUBLE

Touchscreen control panel is not illuminated

POSSIBLE CAUSE

No power at the wall outlet.

REMEDY

Check wall outlet.

No power to the machine inlet.

Check power cord for frayed/broken wires.

Press the button on the circuit breaker.

No power to the control panel.

“Cover Open” screen displayed

Internal electrical failure

Cover open

“Paper Out” screen displayed

Magnetic switch is broken.

In-feed tray is empty.

“Fault detect” screen displayed

Paper misfeed

Black marks on the folded paper

Paper jammed at exit of folder.

In-feed tires, separator, fold rollers and/or sealer rollers are dirty.

Folds are misaligned Fold stop(s) need to be adjusted

Call for service

Close cover

Call for service

Place documents on the in-feed tray.

Reload paper and press the “Reset” icon.

Remove paper and press the “Reset” icon.

Clean the parts with approved roller cleaner and rejuvenator.

Adjust fold stop(s) and/or fine tuning knob

Fold is skewed

Documents are wrinkled or crunched

In-feed tray is out of adjustment.

Paper side guides need to be reset.

Fold plates are not inserted correctly.

Turn skew adjuster knob to remove the skew.

Loosen side guides reset and lock into position, side guides should be evenly spaced

Remove and reinstall fold plates. Be sure they’re properly positioned.

Piece of paper or other material is stuck in the fold plate.

Remove object from the fold plate.

In-feed tray lever does not work

Double feeding forms

Broken spring Call for service

Not feeding documents

Documents stuck together

Feed tire or separator worn

Feed tire dirty

Feed tire or separator worn

Jog forms to remove static electricity.

Call for service

Clean feed tire

Call for service

13