Sharp LC-60E77UN LCD Television Owner's Manual

SHARR

AQUOS

LC1::77

LC-65E77

LIQUID CRYSTAL TELEVISION

Ti_=Li'_VISEURACL

TELEVISOR CON PANTALLA

DE CRISTAL LiQUIDO

OPERATI(

MODE

MANI

NYCE

If]DOLBY

DIGITAL ]

1.41||11TM

HIGH-DEFINITION MULTIMEDIA INTERFACE

IMPORTANT • Please read this operation manual before starting operating the equipment.

IMPORTANT • Veuillez lire ce mode d'emploi avant de commencer b. utiliser I'appareil.

IMPORTANTE • Lea este manual de operaci6n antes de comenzar a operar el equipo.

U n m

LC-60E77U

LC-65E77U

LiQUiD CRYSTAL TELEViSiON

ENGLISH

OPERATION MANUAL

IMPORTANT:

To aid reporting in case of loss or theft, please record the

TV's model and serial numbers in the space provided. The numbers are located at the rear of the TV.

Model No.:

Serial No.:

iMPORTANT INFORMATION

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrow-head symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the product.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE

SLOT, FULLY INSERT.

(LC-60E77UN only)

Q-1

Q-2

iMPORTANT iNFORMATiON

WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment.

CAUTION:

This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment.

To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables and connectors for connections.

DECLARATION OF CONFORMITY:

SHARP MQUID CRYSTAL TELEVISION, MODEL LC-60E77UN/LC-65E77UM

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RESPONSIBLEPARTY:

SHARP ELECTRONICSCORPORATION

Sharp Plaza, Mahwah, New Jersey 07495-1163

TEL: 1-800-BE-SHARP

For Business Customers: URL http://www.sharpusa.com

INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be i i determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

"Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National

Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical."

This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury.

Disposal of these materials may be regulated due to environmental considerations.

For disposal or recycling information, please contact your local authorities, the Electronic Industries Alliance: www.eiae.org, the lamp recycling organization: www.lamprecycle.org

or Sharp at 1-800-BE-SHARP

(For U.S.A. only)

Trademarks

Manufactured under license from Dolby Laboratories.

"Dolby" and the double-D symbol are trademarks of Dolby

Laboratories.

"HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI

Licensing LLC."

Products that have earned the ENERGY STAR _>are designed to protect the environment through superior energy efficiency.

L C F_ _/I'-, L C F O N T, -T--)b_'--_ ;t _ t'- and LC logo mark are registered trademarks of SHARP Corporation.

This product is embedded with LC Font technology, which was developed by SHARP Corporation for clearly displaying easy-to-read characters on LCD screens.

However, other fonts are used for some screen pages, too.

DEAR SHARP CUSTOMER

Thank you for your purchase of the Sharp Liquid Crystal Television.

of trouble-free operation of your product, please read the important

using this product.

To ensure safety and many years

Safety instructions carefully before

iMPORTANT SAFETY iNSTRUCTiONS

Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety.

However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning the product.

To ensure your safety and prolong the service life of your Liquid Crystal Television, please read the following precautions carefully before using the product.

1)

2)

3)

4)

5)

6)

7)

8)

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings.

Install in accordance with the manufacturer's instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

9) lo)

11)

12)

amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

Only use attachments/accessories specified by the manufacturer.

Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus

13)

14)

combination to avoid injury from tip-over.

Unplug this apparatus during lightning storms or when unused for long periods of time.

Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Additional Safety Information

15) Power Sources-This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company.

For products intended to operate from battery power, or other sources, refer to the operating instructions.

16) OverloadingDo not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

17) Object and Liquid EntryNever push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the product.

18) Damage Requiring Service-Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) When the AC cord or plug is damaged, b) If liquid has been spilled, or objects have fallen into the product, c) If the product has been exposed to rain or water, d) If the product does not operate normally by following the operating instructions.

Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation, e) If the product has been dropped or damaged in any way, and f) When the product exhibits a distinct change in performance - this indicates a need for service.

19) Replacement Parts-When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock, or other hazards.

20) Safety Check-Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

21) Wall or ceiling mounting-When mounting the product on a wall or ceiling, be sure to install the product according to the method recommended by the manufacturer.

Q-3


Outdoor Antenna Grounding If an outside antenna is connected to the television equipment, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges.

Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE ANSI/NFPA 70

_ANTENNA

/"_ [1, _

LEADINWIRE

ANTENNA

DISCHARGE UNIT

7" IGRO ND,NG

7ONDUCTORS

@-4

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC -- NATIONAL ELECTRICAL CODE

• Water and Moisture -- Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

Stand -- Do not place the product on an unstable cart, stand, tripod or table. Placing the product on an unstable base can cause the product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart, stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting the product on a wall, be sure to follow the manufacturer's instructions.

Use only the mounting hardware recommended by the manufacturer.

Selecting the location -- Select a place with no direct sunlight and good ventilation.

Ventilation -- The vents and other openings in the cabinet are designed for ventilation.

Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the life of the product.

Do not place the product on a bed, sofa, rug or other similar surface, since they can block ventilation openings.

This product is not designed for built-in installation; do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the manufacturer's instructions are followed.

The Liquid Crystal panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the panel breaks.

Heat The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

The Liquid Crystal panel is a very high technology product with 2,073,600 pixels, giving you fine picture details.

Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red. Please note that this does not affect the performance of your product.

Lightning For added protection for this television equipment during a lightning store% or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to the equipment due to lightning and power-line surges.

Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

To prevent fire, never place any type of candle or flames on the top or near the TV set.

To prevent fire or shock hazard, do not place the AC cord under the TV set or other heavy items.

Do not display a still picture for a long time, as this could cause an afterimage to remain.

To prevent fire or shock hazard, do not expose this product to dripping or splashing.

No objects filled with liquids, such as vases, should be placed on the product.

Do not insert foreign objects into the product.

Inserting objects in the air vents or other openings may result in fire or electric shock. Exercise special caution when using the product around children.

Precautions when transporting the TV

• When transporting the TV, never carry it by holding or otherwise putting pressure onto the display. Be sure to always carry the TV by two people holding it with two hands one hand on each side of the TV.

J

Caring for the Cabinet

Use a soft cloth (cotton, flannel, etc.) and gently wipe the surface of the display panel.

Using a chemical cloth (wet/dry sheet type cloth, etc.) may deform the components of the main unit cabinet or cause cracking.

Wiping with a hard cloth or using strong force may scratch the panel surface.

If the cabinet is very dirty, wipe with a soft cloth (cotton, flannel, etc.) soaked in neutral detergent diluted with water and thoroughly wrung out, and then wipe with a soft dry cloth.

The cabinet is primarily made of plastic. Avoid using benzene, thinner, and other solvents, as these may deform the cabinet and cause the paint to peel off.

Do not apply insecticides or other volatile liquids.

Also, do not allow the cabinet to remain in contact with rubber or vinyl products for a long period of time. Plasticizers

-_ !nside !he p!ast!c may causethe cab!net !o defo!m and cause !he pa!ntto

late ! off: j


r

Caring for the Liquid Crystal panel

• Turn off the main power and unplug the AC cord from the wall outlet before handling.

Gently wipe the surface of the display panel with a soft cloth (cotton, flannel, etc.).

To protect the display panel, do not use a dirty cloth, liquid cleaners, or a chemical cloth (wet/ dry sheet type cloth, etc.). This may damage the panel surface.

Wiping with a hard cloth or using strong force may scratch the panel surface.

Use a soft damp cloth to gently wipe the panel when it is really dirty.

(It may scratch the panel surface when wiped strongly.)

If the panel is dusty, use an anti-static brush, which is commercially available, to clean it.

To avoid scratching the frame or screen, please use a soft, lint free cloth for cleaning. Approved cleaning cloths are available directly from Sharp in single (00Z-LCD-CLOTH) or triple (00Z-LCD-CLOTH-3) packs. Call 1-800-BE-SHARP for

_, ordering, orVISIT www.sharpusa.com/SharpDirect.

Congratulations on your purchase! As you enjoy your new product, please keep these safety tips in mind:

THE iSSUE o The home theater entertainment experience is a growing trend and larger flat panel displays are popular purchases.

However, flat panel displays are not always supported on the proper stands or installed according to the manufacturer's recommendations.

o Flat panel displays that are inappropriately situated on dressers, bookcases, shelves, desks, speakers, chests or carts may fall over and cause injury.

THIS MANUFACTURER CARES!

o The consumer electronics industry is committed to making home entertainment enjoyable and safe.

TUNE INTO SAFETY o One size does NOT fit all. Follow the manufacturer's recommendations for the safe installation and use of your flat panel display.

o Carefully read and understand all enclosed instructions for proper use of this product.

o Don't allow children to climb on or play with furniture and television sets.

o Don't place flat panel displays on furniture that can easily be used as steps, such as a chest of drawers.

o Remember that children can become excited while watching a program, especially on a

"larger than life" flat panel display. Care should be taken to place or install the display where it cannot be pushed, pulled over, or knocked down.

o Care should be taken to route all cords and cables connected to the flat panel display so that they cannot be pulled or grabbed by curious children.

WALL MOUNTING: IF YOU DECIDE TO WALL MOUNT YOUR FLAT PANEL DISPLAY, ALWAYS: o Use a mount that has been recommended by the display manufacturer and/or listed by an independent laboratory (such as UL, CSA, ETL).

o Follow all instructions supplied by the display and wall mount manufacturers.

o If you have any doubts about your ability to safely install your flat panel display, contact your retailer about professional installation.

o Make sure that the wall where you are mounting the display is appropriate.

Some wall mounts are not designed to be mounted to walls with steel studs or old cinder block construction.

If you are unsure, contact a professional installer.

o A minimum of two people are required for installation. Flat panel displays can be heavy.

Note: CEA is the preeminent trade association promoting growth in the $161 billion

CF_

Consumer Electro_ Association

._

U.S. consumer electronics industry. More than 2,200 companies enjoy the benefits of

CEA membership, including legislative advocacy, market research, technical training and

WWW, C[.Org/$afe|y education, industry promotion and the fostering of business and strategic relationships.

Q-5

Contents

iMPORTANT iNFORMATiON .....................

1

Trademarks .......................................

2

DEAR SHARP CUSTOMER .......................

iMPORTANT SAFETY iNSTRUCTiONS ........

3-5

3

Supplied Accessories ............................

6

QUICK REFERENCE

QUICK INSTALLATION TIPS ...................

Using the Remote Control Unit .................

Preparation

Antennas .......................................

8

Installing Batteries in the Remote Control Unit...

8

Part Names

TV (Front) ......................................

TV (Rear/Side) ..................................

Remote Control Unit ...........................

9

9

10

7

7

Connecting to External Equipment

Connecting a Blu-ray Disc/DVD Player or

HD Cable/Satellite Set-top Box ...........

Connecting a VCR, Game Console,

11-12

Camcorder or Cable/Satellite Set-top Box ....

12

Connecting an Audio Amplifier .................

13

Connecting a PC ..............................

14

Watching TV

Turning On/Off the Power .....................

Initial Setup ....................................

15

15

Direct Button Operation

Changing Channels .......................

Changing Volume ..........................

MUTE ......................................

16

16

16

Sleep Timer ................................

FLASHBACK ...............................

SURROUND ...............................

FREEZE ....................................

INPUT ......................................

AV MODE ..................................

AUDIO .....................................

POWER SAVING ...........................

Closed Captions and Digital Closed Captions...

18

VIEW MODE ...............................

19

16

16

16

16

16

17

17

18

On=Screen Display Menu

On-Screen Display Menu Operation ...........

Menu Operation Buttons ......................

Menu Items ...................................

Picture Menu ...............................

Audio Menu ...................................

Power Control Menu ..........................

Setup Menu ................................

Option Menu ...............................

Digital Setup Menu .........................

20

20

21

22-23

24

24

25-28

29-30

31-32

Other Viewing Options

Presetting Remote Control Function ...........

Operating the Connected Equipment ..........

Using AQUOS LiNK

Controlling HDMI Equipment

Using AQUOS LINK .......................

AQUOS LINK Menu ........................

33

33

35-37

37-38

Using a PC

Displaying a PC Image on the Screen ..........

Adjusting the PC Image .......................

Setting Audio Input ............................

PC Compatibility Chart ........................

RS-232C Port Specifications ..................

Appendix

Removing the Stand ...........................

Setting the TV on the Wall .....................

Troubleshooting ............................

Troubleshooting - Digital Broadcasting .........

Specifications .................................

Optional Accessory ............................

Information on the Software License for

This Product .................................

42

42

43-44

44

45

45

46

39

40

40

40

41

Calling for Service ...............................

LIMITED WARRANTY ............................

47

47

Dimensional Drawings o The dimensional drawings for the LCD TV set are shown on the inside back cover.

Supplied Accessories

Make sure tile following accessories are provided with tile product.

r

LC-60E77UN LC-65E77UM

Remote control unit

(x 1)

Page 7

"AAA" size battery

(x 2)

Page 8

(2-prong)

AC cord

(x 1)

Page 7

(3-prong)

Cable clamp Operation manual

(x 1)

Page 7

(x 1)

Q-6

• Always use the AC cord supplied with the TV.

• The illustrationsabove are for explanation purposes and may vary slightly from the actual accessories.

QUICK REFERENCE

1 Attach your antenna to the back of the television.

(See page 8.)

2 Connect the AC plug for the television into the AC outlet.

Use the remote control unit by pointing it towards the remote control sensor on the TV. Objects between the remote control unit and the remote control sensor may prevent proper operation.

LC-60E77UN

(2-prong)

LC-65E77UM

(3-prong)

Place the TV close to the AC outlet, and keep the power plug within reach.

This product must only be connected to a 120 V, 60 Hz, grounded (3-prong) outlet.

Connecting it to any other kind of outlet will damage the product and invalidate the warranty. (LC-65E77UM only)

TO PREVENT RiSK OF ELECTRIC SHOCK, DO NOT

TOUCH UNqNSULATED PARTS OF ANY CABLES

WiTH THE AC CORD CONNECTED.

3 Bundle the cords properly with the cable clamp.

1T(5 m)

30°

30 °

30°

Cautions regarding the remote control unit o Do not expose the remote control unit to shock. In addition, do not expose the remote control unit to liquids, and do not place in an area with high humidity.

o Do not install or place the remote control unit under direct sunlight. The heat may cause deformation of the remote control unit.

The remote control unit may not work properly if the remote control sensor on the TV is under direct sunlight or strong lighting. In such cases, change the angle of the lighting or the TV, or operate the remote control unit closer to the remote control sensor.

4 How to turn on the television for the first time.

A) Press POWER on the television.

B) The POWER indicator on the front of the television lights GREEN.

iMPORTANT:

The POWER indicator on the television should light GREEN indicating you have power to the television.

If the POWER indicator on the television still does not light up, press TV POWER on the remote control to turn the power on.

iMPORTANT:

IF THE UNIT DOES NOT POWER ON - UNPLUG THE

TELEVISION FROM THE OUTLET AND REPEAT THE

INSTALLATION STEPS.

IF YOU STILL ENCOUNTER NO POWER, PLEASE CONTACT

US AT 1-800-BE-SHARP.

POWER indicator

Speakers cannot be detached from the TV.

TV angle cannot be adjusted.

Q-7

Preparation

To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm coaxial cable with an F-type connector, plug it into the antenna terminal at the rear of the TV set.

f

1 .A 75-ohm system is generally a round cable with F-type connector that can easily be attached to a terminal without tools (Commercially available).

_ F-type connector

75-ohm coaxial cable (round)

2.A 300-ohm system is a flat "twin-lead" cable that can be attached to a 75-ohm terminal through a 300/75-ohm adapter (Commercially available).

300-ohm twin-lead cable (flat)

F=type connector should be finger=tightened only.

,,_,_:/_ '_.?\_\F-type connector

When connecting the RF cable to the TV set, do not tighten F-type connector with tools.

If tools are used, it may cause damage to your TV set. (The breaking of internal circuit, etc.)

._,_j_.

_ q_, .'\

.<

75-ohm coaxial cable

Connecting Antenna

Cable

• Connect the antenna cable to the TV using one of the methods in the illustration as shown ((_, (_, (_ or (_).

Home Antenna terminal (75 ohm)

(_ Cable without a CATV converter

_ _-;_,_C

Coaxial cable

=

(_) VHF/UHF antenna

(_ Combination

UHF antenna

VHF/

_7

_

5-ohm coaxial cable (round) t 75_ohm coaxial cable (round)

HomeAnt ....

terminal (commercially available)

Coaxial cable

(

..........

j

(_ Separate VHF/UHF antenna

To TV antenna terminal

L :.Q

If the remote control fails to operate TV functions, replace the batteries in the remote control unit.

1 Open the battery cover.

2 Insert two "AAA" size batteries

(supplied with the product).

3 Close the battery cover.

Q-8

= Place the batteries with their terminals corresponding to the (+) and (-) indications in the battery compartment.

Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.

= Do not mix batteries of different types. Different types of batteries have different characteristics.

= Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage in old batteries.

= Remove batteries as soon as they are worn out. Chemicals that leak from batteries that come in contact with skin can cause a rash. If you find any chemical leakage, wipe thoroughly with a cloth.

= The batteries supplied with this product may have a shorter life expectancy due to storage conditions.

= If you will not be using the remote control unit for an extended period of time, remove batteries from it.

Part Names

II /

r

_ r ........

_t oPc,nd,eator 22.//

|

* OPC: Optical Picture Control

*2

POWER

POWER button

AC INPUT terminal l

MENU

..........

INPUT

MENU button

LC-60E77UN LC-65E77UM iNPUT button

CH

/N

v

VOL

I_1 +

Channel buttons

(CH/VV)

Volume buttons

(VOL+/-)

iNPUT 7 terminal

(HDMI) iNPUT 8 terminal

(HDMI)

DIGITAL AUDIO

OUTPUT terminal

AUDIO OUTPUT terminals

II1_

"1 S-VIDEOICOMPO-

®®

R-AUDIO-L

VIDEO COMPO-

NENT

(',e;)

ANT/CABLE

_ Antenna!Cable

in iNPUT 5

(HDMI) iNPUT 3 terminals iNPUT 1 terminals iNPUT 2 terminals

RS-232C terminal

SERVICE terminal

INPUT 4 terminal (P©-IN)

(shared for INPUT 4 and INPUT 6) *4

6 terminal (HDMI)

"1 See pages 11, 12, 13, 14 and 35 for external equipment connection.

*2 See page 20 for button operations.

*3 See page 7 for connecting the AC cord.

*4 See page 40 for details on the PC Audio Select function.

The illustrations in this operation manual are for explanation purposes and may vary slightly from the actual operations.

The examples used throughout this manual are based on the LC-65E77UM model.

@-9

Part Names

1 17

_I_Tv, ovoV°R°

_ LIGHT

18

5 _

7

12

13

14

15

16

_

T ....

, i i iiiiiiiii "i

_

.....T

•

20

21

22

23

24

25

26

27

28

29

3O

iii_

2

3

5

6

7

1

4

"IV POWER: Switch the TM power on or enter standby. (See page

15.)

DISPLAY: Display the channel inlermation.

SOURCE POWER: Turns the power of the external equipment on and off.

External equipment operational buttons: Operate the external equipment.

0-9: Set the channel. (See page 16.)

• (DOT}: (See pages 16 and 33.)

INPUT: Select a TM input source. (l_/, INPUT 1, INPUT 2, INPUT 3,

INPUT 4, INPUT 5, INPUT 6, INPUT 7, INPUT 8) (See page 16.)

8

9

VOL+/-: Set the volume. (See page 16.)

POWER SAVING: Select Power Saving settings. (See page 18.)

10 FREEZE: Set the still irrlage. Press again te return to normal screen. (See page 16.)

11 EXIT: Turn off the menu screen.

12 OPTION: Display the AQUOS LiNK MENU screen. This butten will functk)n only when AQUOS LINK is used• (See pages 35 to 38 for details.)

13 REC STOP: Stops one touch recording. This button will function only when AQUOS LINK is used. (See pages 35 te 38 for details.)

14 SLEEP: Set the sleep timer. (See page 16.)

15 SURROUND: Select Surround settings. (See page 16•)

16 AUDIO: Selects the MTS/SAP or the audio mode during multichannel audio broadcasts.

(See page 17.)

17 FUNCTION: Switches the remote control for R/, CBL/SAT, VCR,

DVD and AUDIO operation.

Indicator lights up for the current mode. (See pages 33 to 34 for details.)

• To enter the code registration mode, you need to press

FUNCTION and DISPLAY at the same time.

18 LIGHT i_: When this button is pressed, some buttons (for example, VOL+/and CHA/V) on the remote control unit will light. The lighting will turn off if no operalions are performed within about 5 seconds. This button is used for performing operations in low-light situations.

19 VIEW MODE: Select the screen size. (See pages 19 and 39.)

20 ENT: Jumps to a channel after selecting with the 0---9 buttons.

21 FLASHBACK: Return to the previous channel or external input mode. (See page 16.)

22 CHA/V: Select the channel. (See page 16.)

23 MUTE: Mute the sound. (See page 16.)

24 MENU: Display the menu screen.

25 J,/V/_I/I_, ENTER: Select a desired item on the screen•

26 RETURN: Return to the previous menu screen.

27 FAVORITE CH

A, B, C, D: Select 4 preset favorite channels in 4 diffgrent categories.

(See page 30.)

While watching, you can toggle the selected channels by pressing

A, B,C and D,

28 FAVORITE: Set the favorite channels. (See page 30.)

29 CC: Display captiens from a closed-caption source. (See page 18.)

30 AV MODE: Select an audio or video setting.

(When the input source is T_/, INPUT 1, 2 or 3: STANDARD,

MOVIE, GAME, USER, AUTO, DYNAMIC (Fixed), DYNAMIC.

When the input source is INPUT 4, 5, 6, 7 or 8: STANDARD,

MOVIE, GAME, PC, USER, AUTO, DYNAMIC (Fixed), DYNAMIC)

(See page 17.)

Q-10

• When using the remote control unit, point it at the TV.

Connecting to External Equipment

You can connect many types of external equipment to your TV. To view external source images, select the input source from INPUT on the remote control unit or on the TV. (See page 16.)

For connecting the TV to external equipment, use commercially available cables.

To protect equipment, always turn off the TV before connecting any external equipment.

Please read the relevant operation manual (Blu-ray disc player, etc.) carefully before making connections.

When using HDMI cable (INPUT 5, 6, 7 or 8):

The HDMI (High Definition Multimedia Interface) terminal is an audio-video interface that enables a connection for audio and video signals using a single cable. The HDMI terminal supports high-resolution video input.

Side panel Blu-ray disc player • DVD player

HD cable/satellite set-top box

HDMI-certified cable

_?;22

?

<_i[J

i["

To enjoy 1080p display capability, connect your external equipment using an HDMI-certified cable or a component cable and set the equipment to 1080p output.

cable (INPUT 6):

Rear of the TV m When using HDMI=DVI conversion

Blu-ray disc player • DVD player


HDMI-DVl conversion cable

When using an HDMI-DVl conversion cable, you should make an analog audio connection.

In this case, in addition to connecting an HDMI-DVl conversion cable to the INPUT 6 (HDMI) tern_inal, connect an audio cable to the AUDIO terminal and set "PC Audio Select" to "Input 6 (HDMI)". (See page 40.)

Q-11

Connecting to External Equipment

When using Component cable (INPUT 1 or 2}:

BID-ray disc player • DVD player


Rear of the TV

Audio cable

I

?

"

;:;:

/"

: ..............

_ a NENT NENT co_oco_o-ll

AUDIO

•

a

AU{

Component video cable

PR(Bed)_._..€ _Y(Green)

PB (Blue)

To enjoy 1080p display capability, connect your external equipment using an HDMI-certified cable or a component cable and set the equipment to 1080p output•

See page 11 for connecting a BID-ray disc player, DVD player or an HD cable/satellite set-top box to the HDMI terminal.

The COMPONENT terminals take priority over the VIDEO (INPUT 1) and S-VIDEO (INPUT 2) terminals.

m When using S-VIDEO cable (INPUT 2}:

= Game console = Can]corder

• VCR

Rear of the TV i iii

S-VIDEO cable

Audio cable m When using Composite

• Game console • VCR cable (iNPUT 1 or 3}:

Camcorder • Cable/Satellite set-top box

AUDIO-L

AUDIO-R I

Side panel Rear of the TV

AV cable

VIDEO(Yellow)J

AUDIO-L(White) _/_

AUDIO-R(Red)_

/ i ,oll

Q-12

The COMPONENT terminals take priority over the VIDEO (INPUT 1) and S-VIDEO (INPUT 2) terminals.

Connecting to External Equipment m When using optical fiber cable:

It is possible to output audio through the DIGITAL AUDIO OUTPUT terminal. (See page 31 for details.) PCM audio outputs from the terminal.

Rear of the TV

Optical fiber cable

Depending on the connected equipment, audio will not output from the DIGITAL AUDIO OUTPUT terminal in HDMI connection.

In this case, set the audio formats of the connected equipment to PCM, 32/44.1/48 kHz.

When using audio cable: Rear of the TV

Audio cable

(Red)

31 b-L (White)

Q-13

Connecting to Externa( Equipment

Refer to page 40 for a list of PC signals compatible with the TV.

When using HDMI cable (iNPUT 5, 6, 7 or 8}: Side panel Rear of the TV

HDMI-certified cable

V_D_O i

AUE _

Depending on the board, only video signals may be output. In this case, in addition to connecting an HDMI-certified cable to the

INPUT 6 (HDMI) terminal, connect an audio cable to the AUDIO terminal and set "PO Audio Select" to "Input 6 (HDMI)". (See page 40.)

• The HDMI terminals only support digital signal.

m When using HDMI-DVI conversion cable (iNPUT 6): Rear of the TV

HDMI-DVI conversion cable

® 3.5 mm stereo minijack cable

When using an HDMI-DVl conversion cable, you should make an analog audio connection.

In this case, in addition to connecting an HDMI-DVl conversion cable to the INPUT 6 (HDMI) terminal, connect an audio cable to the AUDIO terminal and set "PC Audio Select" to "Input 6 (HDMI)". (See page 40.) m When using analog RGB cable (iNPUT 4}: Rear of the TV

I

,_...

® 3.5 mm stereo minijack cable

_]_ RGBcable _]_.

Q-14

When using an analog RGB cable, input the audio signal to the AUDIO terminal of INPUT 4.

When connecting a PC to the INPUT 4, set "PC Audio Select" to "Input 4 (PC)". (See page 40.) i i

Watching TV

..... o o

_:_j o o i SOURCE o

_,GHT

1

POWER

"P,/POWER

(On/Standby) turn the power on.

o POWER indicator (Green): The TV is on. (After a few seconds, a window appears with sound.)

Press POWER on the TV, or TV POWER on the remote control unit to o The initial setup starts when the TV powers on for the first time. If the TV has been turned on before, the initial setup will not be invoked. For changing the settings of the initial setup, perform "EZ setup" on the Setup menu on page 25.

Press POWER on the TV, or TV POWER on the remote control unit again to turn the power off.

o The TV enters standby and the image on the screen disappears.

o The POWER indicator on the TV turns off.

o If you are not going to use this TV for a long period of time, be sure to remove the AC cord from the AC outlet.

o Weak electric power is still consumed even when the TV is turned off.

When you turn on the TV for the first time, it will automatically memorize the broadcasting channels available in the region where you live. Perform the following steps before you press TV POWER on the remote control unit.

1.

Insert the batteries into the remote control unit. (See page 8.)

2.

Connect the antenna cable to the TV. (See page 8.)

3.

Plug in the AC cord to the AC outlet. (See page 7.)

FREEZE MENU

ENERGY STAR qualification is based on AV MODE "STANDARD"

Air/Cable (Antenna setting}

Make sure what kind of connection is made with your TV when selecting "Air" or "Cable".

3 Press _1/_ to select "Air" or "Cable".

Press ENTER to enter the setting.

Language (Language setting)

Select from among 3 languages: English, French and Spanish.

1 Press A/V to select the desired language listed on the screen, and then press ENTER.

language

CH Search (Channel search)

Channel auto search makes the TV look for all channels viewable in the set area.

4 When "Air" is selected in Antenna setting:

Press 41/_ to select "Start", and then press ENTER.

TV Location

Select "Home" or "Store" for the location where you plan to install the TV. This product qualifies for ENERGY STAR V3.0

in Home mode default setting,

2 Press _/_ to select "Home" or "Store".

Press ENTER to enter the setting.

When "Cable" is selected in Antenna setting:

Press A/Y to select "Analog & Digital Search Start" to search both analog and digital broadcasts, or to select

"Analog Search Start" to search only analog broadcasts, and then press ENTER.

Home: "Power Saving" is set to "Advanced",

MODE is set to "STANDARD".

and AV

Store: "Power Saving" is set to "Off" and AV MODE is set to

"DYNAMIC (Fixed)", Picture Reset and Feature Demo can be set,

Picture Reset: AV MODE will be set to "DYNAMIC (Fixed)" regardless of whether Picture Reset is "On" or "Off", If you select "On", AV MODE will be reset to "DYNAMIC (Fixed)" if there is no operation for 30 minutes. When "Off" is selected,

AV MODE will be set to "DYNAMIC (Fixed)",

Feature Demo: When "On" is selected, after all the settings are completed, the Fealure Demo screen is displayed if there is no operation for several minutes,

,, The Channel search will start automatically.

,, To exit the Channel search screen, select "Cancel", and then press ENTER.

o If no channel is found, confirm the type of connection made with your TV and try "EZ Setup" again.

(See page 25.)

For changing the settings of the initial setup, perform "EZ setup" on the Setup menu on page 25.

(D-15

Direct Button Operation

(D-16

OQQ

®@®

®Q®

®@@

INPUT FLASHBACK

@@

CH

FREEZE

--

®®@®

S_OUND

MENU

@ d:::z::b o

FAVORITECH --

You can change channels by pressing CNA/V or 0-9,

• (DOT).

Examples:

To select a 1 or 2-digit channel number (eog., Channel 5):

Press5 > ENT.

To select a 3-digit channel number (e.g., Channel 115}:

Press 1 > 1 ...................

ENT.

To select a 4-digit channel number (e.g., Channel 22.1):

Press 2 ---> 2 --_, (DOT} -_ 1 --->ENT.

When selecting a 1-digit channel number, it is not necessary to press 0 before the number.

When you enter 0-9 only, channel selection will be made if there is no operation within a few seconds.

If you push "0" by itself, nothing will happen.

Complete the above steps within a few seconds.

When you enter 0-9 and • (DOT), channel selection will be made if there is no operation within a few seconds.

You can change the volume by pressing VOL+/the TV or on the remote control unit.

To increase the volume, press VOL+.

To decrease the volume, press VOL J.

IN .....

7 I

Audio status

Speaker

0

VOL

E

Variable sound Mute on

When "Output Select" is set to "Variable", the indicator on

I

the screen changes as shown below.

Allows you to set a time when the TV automatically switches to standby.

Press SLEEP.

o Theremainingtime displayswhen the sleep timerhas beenset.

Each time you press SLEEP, the remaining time switches as shown below.

Off u, 30 u, 60 _ 90 _ 120 t I

When set, the time automatically starts counting down.

If you want to adjust the sleep timer, you can press SLEEP twice then change the time setting.

When it is 5 minutes before the time expires, the remaining time will start to keep appearing every minute.

Select "Off" by pressing SLEEP to cancel the sleep timer.

The 11/will enter standby when the remaining time reaches 0,

Press FLASHBACK to switch to the previously tuned channel.

Press FLASHBACK againto switch backtothe currently tuned channel.

FLASHBACK will not work if no channel has been changed after the TV is turned on.

The surround function produces Surround effect from the speakers. Each time you press SURROUND, the mode changes between On and Off.

On; Makes it possibleto enjoy natural, realistic surround sound.

Off: Outputs the normalsound.

You can have the same settings by choosing "Surround" on the menu items. (See page 24.)

Allows you to capture and freeze a moving image that you are watching.

Press FREEZE.

A moving image is captured,

Press FREEZE againto cancel the function,

When this function is not available, "No displaying still image available." will display.

The still image automatically goes out after 30 minutes.

If you are using the freeze function and a broadcast activates the V-CHIP BLOCK, the freeze function will be canceled and a V-CHIP BLOCK message will appear.

See page 29 for details on the Output Select function.

Mutes the current sound output.

Press MUTE.

"E_)" will be displayed on the screen for 30 minutes, and the sound is silenced.

Within 30 minutes of pressing MUTE, mute can be canceled by pressing VOL +/or MUTE.

Mute will be canceled after 30 minutes have passed.

However, the TV will not suddenly output a loud sound as the volume level is set to 0 automatically.

To view external source images, select the input source using INPUT on the remote control unit or on the TV.

1 Press INPUT,

= A list of selectablesources appears.

2 Press INPUT again or press A/T to select the input source.

input in,

See pages 11, 12, 13, 14 and 35 for external equipment connection.


AV MODE gives you several viewing options to choose from to best match the surrounding environment of the

TV, which can vary due to factors like room brightness, type of program watched or the type of image input from external equipment.

Press AV MODE. Current AV MODE displays.

= Press AV MODE again before the mode displayed on the screen disappears.

The mode changes as shown below:

Example:

When the input source is TV, iNPUT 1, 2 or 3 terminals

STANDARD._

MOVIE._

GAME _ USER [TV]

!

!

DYNAMIC _ DYNAMIC (Fixed) _ AUTO

Example:

When the input source is iNPUT 4, 5, 6, 7 or 8 terminals

STAN DARD--_MOVlE _ GAME _PC _,USER[ fP]

DYNAMIC _ DYNAMIC (Fixed) _ AUTO

STANDARD: For a highly defined image in a normal lighting.

MOVIE: For a movie.

GAME: Lowers image brightness for easier viewing.

PC: For PC.

USER: Allows the user to customize settings as desired.

You can set the mode for each input source.

AUTO: Optimizes the image quality automatically based on the room brightness and image signal.

DYNAMIC (Fixed}: Changes the image and sound settings to the factory preset values. No adjustments are allowed.

DYNAMIC: For a clear-cut image emphasizing high contrast, useful for sports viewing.

= You can select a different AV MODE item for each input mode. (For example, select STANDARD for TV input and

DYNAMIC for INPUT 1.)

= When you play games, "GAME" is recommended for AV

MODE.

II MTS/SAP stereo mode

The TV has a feature that allows reception of sound other than the main audio for the program. This feature is called Multi-channel Television Sound (MTS). The TV with MTS can receive mono sound, stereo sound and Secondary Audio Programs (SAP). The SAP feature allows a TV station to broadcast other information, which could be audio in another language or something completely different like weather information.

You can enjoy Hi-Fi stereo sound or SAP broadcasts where available.

= Stereo broadcasts: View programs like live sporting events, shows and concerts in dynamic stereo sound.

= SAP broadcasts: Receive TV broadcasts in either MAIN or SAP sound.

MAIN sound: The normal program soundtrack (either in mono or stereo).

SAP sound: Listen to a second language, supplementary commentary or other information. (SAP is mono sound.)

If stereo sound is difficult to hear.

= Obtain a clearer sound by manually switching to fixed mono-sound mode.

You can change MTS as shown below to match the television broadcast signal.

Press AUDIO to toggle between audio modes.

Examples: when receiving MTS and SAP

STEREO mode: STEREO_,_ MONO

STEREO + SAP mode: ST(SAP) ,=, SAP(ST),=, MONO

"It I

MAIN + SAP mode: MAIN_ SAP

MONO mode: MONO

II Digital broadcasting audio mode

The types of audio transmitted in a digital broadcast include

SURROUND as well as MONO and STEREO. In addition, it is possible for multiple audio tracks to accompany a single video track.

Press AUDIO to toggle between audio modes.

Example: when receiving Digital broadcasting

STEREO (Audio1) ._

STEREO (Audio2)

t...... SURROUND (Audio3) 4_..-1

= MTS only operates while in TV mode.

Q-17


Allows you to set the Power Saving level in order to decrease the power consumption and increase the backlight lifespan.

Press POWER SAVING.

= Each time you press POWER SAVING, the mode changes as shown below.

Off ,m, Standard ,m, Advanced t !

1 Press CO.

= This will present the Closed Caption information display.

2 Press CC while the Closed Caption information is still on the screen.

= Press repeatedly until you select the desired closed caption service.

= You can have the same settings by choosing "Power

Saving" on the menu items. (See page 24.)

Your TV is equipped with an internal Closed Caption decoder. It allows you to view conversations, narration and sound effects as subtitles on your TV. Closed

Captions are available on some TV programs and on some VHS home video tapes at the discretion of the program provider.

Digital Closed Caption service is a new caption service available only on digital TV programs (also at the discretion of the service provider). It is a more flexible system than the original Closed Caption system, because it allows for a variety of caption sizes and font styles. When the Digital Closed Caption service is in use, it will be indicated by the appearance of a 3-letter abbreviation that also indicates the language of the

Digital Closed Captions: ENG (English), SPA (Spanish),

FRA (French) or other language codes.

Not all programs and VHS videotapes offer closed captions. Please look for the "[_]" symbol to ensure that captions will be shown.

In the Closed Caption system, there can be more than one caption service provided.

Each is identified by its own number. The "CC1" and "CC2" services display subtitles of TV programs superimposed over the program's picture.

In the Closed Caption system, the "Text1" or "Text2" services display text that is unrelated to the program being viewed (e.g., weather or news). These services are also superimposed over the program currently being viewed.

Closed Caption information

= Depending on the number of caption servicesin the signal being received,you will see information such as

1/2 or 1/4 displayed.

1/2 means "the first of two services".

Example:

If a program has three services (DigitalCC(ENG),CC1 and Text1), the closed caption display will toggle in this sequence: t I

The CO button keeps a record of the last service selected in its memory.

If the last closed caption mode (e.g. 1/3 ENG) you selected is not available for the next program, or on another channel, the closed caption service that is available is automatically selected, and this service appears in parentheses, e.g. "1/3(CC1)".

Closed Caption services that appear in parentheses will not be stored in the CC button's memory as your last selected service.

Only services that you have selected with the CC button are stored.

Examples:

In a case where there are two closed caption services provided (for instance, Digital CC(ENG) and CC1), and Digital CC(ENG)is displayed as your current selection, if Digital CC(ENG) is not broadcast for the next program, the other closed caption service, CC1, will be displayed in parentheses.

A closed caption service appears in parentheses because the service you selected is not available and a different service is displayed on your screen.

"1/1 (CC1)" is displayed instead of "I/2/ENG".

= When "Power Saving" is set to "Standard" or "Advanced", the Power Saving leaf icon appears on the channel information window. See page 24 for details of Power

Saving settings.

= See page 30 for detailed closed caption settings.

= When the program contains no closed caption, "--" displays in the closed caption information.

= If the language code, e.g. "ENG", is not found on Digital TV programs, "--" will be shown.

o Four kinds of closed caption service (CC1, CC2, Text1,

Text2) are potentially available, but a broadcast may contain none or only some of these services at the discretion of the program provider.

(D-18


You can select the screen size.

1 c_ c_ c_D

SOURCE LIGHT

C@9

1 Press VIEW MODE. o The View Mode menu displays,

The menu lists the View Mode options selectablefor the type of video signal currently being received.

2 Press VIEW MODE or A/V while the View Mode menu is displayed to select a desired item on the menu.

You can sequentially select a View Mode that has its own aspect ratio.

m For 4:3 programs

Example: Screen size images

Side Bar S.Stretch

(Smart stretch} Zoom Stretch

Suitable for viewing conventional 4:3 programs in their normal format.

o o

Suitable for stretching 4:3 programs to fill the screen.

Suitable for viewing widescreen 2.35:1 anamorphic

DVDs in full screen.

This mode is usefulfor 1,78:1

DVDs, When viewing 1,85:1

DVDs, stretch mode will still show very thin black bands at the top and bottom of the screen, m For HD programs

Stretch: Suitable for viewing wide-screen 1.78:1 aspect ratio program, stretch mode will still show very thin black bands at the top and bottom of the screen.

Dot by Dot (1080i/p only}: Detects the resolution of the signal and displays an image with the same number of pixels on the screen.

Full Screen (720p only}: You can select "Full Screen" only when receiving a 720p signal.

S.Stretch

(Smart stretch}: Suitable for stretching 4:3 programs to fill the screen.

Zoom: Suitable for viewing wide-screen 2.35:1 aspect-ratio programs in full screen.

When using Dot by Dot or Full Screen, it is possible to see noise or bars around different outer portions of the screen. Please change view mode to correct this.

@-19

On=Screen Display Menu

®

Example

_ LCFONT embedded

IIIIIIIIIIIIIIIIIIIIIIIIIIII

Example

[_ Option

PC Audio Select

®

®

®

the remote control. The bar will change in accordance with each menu setting screen.

(i._ Press 4/_ to select the desired item.

(9 Press A/T to select the desired item.

(._ Press 4/_ to adjust the item.

]

(1._ Item displayed in yellow o This indicates the item currently selected.

o Press ENTER to go to the adjustment screen for this item.

(9 Item in brackets

• This indicates the current setting for the item.

(_ Item displayed in white o This indicates that the item can be selected.

(_ Item displayed in gray o This indicates that the item cannot be selected.

There are various reasons why the items cannot be selected, but the main reasons are as follows:

--Nothing is connected to the selected input terminal.

--The function is not compatible with the current input signal.

= Menu options differ in the selected input modes, but the operating procedures are the same.

= The screens in the operation manual are for explanation purposes (some are enlarged, others cropped) and may vary slightly from the actual screens.

LCFONT:

= This product is embedded with LC Font technology, which was developed by SHARP Corporation for clearly displaying easyto-read characters on LCD screens.

Using the remote control

Use the following buttons on the remote control to operate the menu.

ENTER:

RETURN:

i O ® j

FREEZE

E(_T

MENU

RE_RN

!

Press to open or close the menu screen.

Press to select a desired item on the screen or adjust a selected item.

Press to go to the next step or complete the setting.

Press to return to the previous step.

Using the control panel of the main unit

You can also operate the menu with the control panel of the main unit.

Button operations on the control panel correspond to the ones on the remote control as shown below.

m

_owE_ i

MENU: MENU on the remote control.

INPUT: ENTER on the remote control.

OH/X/V: Cursor A/T on the remote control.

(D20

On=Screen

Menu o When AV MODE is set to "AUTO", part of the menu may not be displayed correctly or the setting range of the menu may be changed.

o Some menu items may not be displayed depending on the selected input source.

o When configuring a menu, be sure to select the input source according to the menu items to be configured. If a menu is not displayed, check whether one of the following may be the source of the problem.

•1 A TV program is being viewed (TV).

•2 Audio and video are being inputted to the TV from external analog equipment (INPUT 1,2 or 3).

•"_Audio and video are being inputted to the TV from a computer (INPUT 4).

•4 Audio and video are being inputted to the TV from external HDMI equipment (INPUT 5, 6, 7 or 8).

/_ Picture Menu

OPC .................................................

Page 22

Backlight ..........................................

Page 22

Contrast ...........................................

Page 22

Brightness ........................................

Page 22

Color ................................................

Tint ...................................................

Page 22

Page 22

Sharpness ........................................

Page 22

Advanced

C.M.S.-Hue ...........................

Page 22

C.M.S.-Saturation ................. Page 22

C.M.S.-Value .........................

Page 22

Color Temp ..........................

Page 22

Fine Motion Enhanced .......... Page 23

Active Contrast ..................... Page 23

Gamma Adjustment .............. Page 23

Black Level ............................

Page 23

Film Mode .............................

Page 23

Digital Noise Reduction ......... Page 23

3D-Y/C .................................

Page 23 ,s ,4

Monochrome ........................

Page 23

Range of OPC .......................

Page 23

Reset ................................................

Page 22

Audio Menu

Treble ...............................................

Page 24

Bass .................................................

Page 24

Balance ............................................

Page 24

Surround ..........................................

Page 24

Bass Enhancer .................................

Page 24

Reset ................................................

Page 24

_ Power Control Menu

Power Saving ...................................

Page 24

No Signal Off ....................................

Page 24

No Operation Off ..............................

Page 24

I_9 Setup Menu

EZ Setup ..........................................

Page 25,2 ,s ,4

CH Setup .........................................

Page 25,2 ,s ,4

Antenna Setup-DIGITAL ................... Page 25,2 ,s ,4

Input Skip .........................................

Page 25

Auto Sync ........................................

Page 40,4,2,4

Input Label .......................................

Page 25"4

Parental CTRL ...........................

Pages 26-28 *'_.4

Fine Sync ........................................

Page 40,4,2,4

Position ............................................

Page 26 *'_

Language .........................................

Page 26

Reset ................................................

Page 26

Option Menu

AQUOS LINK Setup .........................

Page 36

Audio Only ........................................

Page 29

Input Select

(for INPUT 1 or 2) ............................

Page 29"4 ,s,4

HDMI Setup .....................................

Page 29 *4,2,3

PC Audio Select ...............................

Page 40

Auto Volume .....................................

Page 29

Clear Voice .......................................

Page 29

Output Select ...................................

Page 29

Color System ....................................

Page 30,4 ,s ,4

Caption Setup ..................................

Page 30,3,4

Digital Caption Info ...........................

Page 30 *'_.4

Program Title Display ........................

Page 30 *'_.4

Favorite CH ......................................

Page 30,2 ,s ,4

Game Play Time ...............................

Page 30"4

Operation Lock Out ..........................

Page 30

Channel Selecting Effect ................... Page 29

Demo Mode .....................................

Page 30

Digital Setup Menu

Audio Setup .....................................

Page 31 ,s,4

Identification .....................................

Page 31,3,4

Software Update .......................

Pages 31-32

=

Q-21

On=Screen Display Menu

Adjusts the picture to your preference with the following _icture settings.

Example

Picture ]

Automatically adjusts the brightness of the screen.

Off: The brightness is fixed at the value set in "Backlight".

On: Automatically adjusts.

On: Display: Displays the OPC effect on the screen while adjusting the brightness of the screen.

= When set to "On", the Optical Picture Control (OPC) senses the surrounding light and automatically adjusts the backlight brightness.

Make sure nothing obstructs the OPC sensor, which could affect its ability to sense surrounding light.

= When set to "On: Display", OPC effect displays on the screen while the OPC adjusts the screen brightness.

= When set to "On" or "On: Display", the OPC indicator on the TV lights green.

This TV provides various advanced functions for optimizing the picture quality.

0 li FREEZE

®

MENU

1 Press MENU to display the MENU screen, and then press 4/!_

to select "Picture".

2 Press A/V to select a specific adjustment item.

o Select "Advanced" and then press ENTER to set

"C. MS.-Hue", "C. MS.-Saturation", "C. M.S.-Value",

"Color Temp.", "Fine Motion Enhanced", "Active

Contrast", "Gamma Adjustment", "Black Level",

"Film Mode", "Digital Noise Reduction", "3D-Y/C",

"Monochrome" or "Range of OPC".

3 Press A/T(or _1/!_) to select the desired setting, and then press ENTER.

4 Press MENU to exit.

Backlight

Contrast

Brightness

Color

Tint

Sharpness

The screen dims

For less contrast

For less brig htness

For less color intensity

Skin tones become reddish

For less sharpness

The screen brightens

For more contrast

For more brightness

For more color intensity

Skin tones become greenish

For more sharpness

For resetting all Picture adjustment items to the factory preset values, press A/T to select "Reset", press ENTER, press 4/1_ to select "Yes", and then press ENTER,

©clot tone is managed using the six-color adjustment setting.

C.M.S.-Hue: This is a standard to adjust the color either more reddish or more bluish in tone.

C.M.S.-Saturation: Increases or decreases the saturation of a selected color.

C.M.S.-Value: A higher value makes the image brighter.

A lower value makes the image darker.

= For resetting all adjustment items to the factory preset values, press A/V to select "Reset", and then press

ENTER.

For a better white balance, use color temperature correction.

High: White with bluish tone

Middle:

Mid-Low:

Low: White with reddish tone

White balance can be adjusted between a maximum of

+30 and a minimum of -30 for each color temperature.

R Gain (LO/HI}: -30 through +30

G Gain (LO/HI): -30 through +30

B Gain (LO/HI): -30 through +30

= For resetting all adjustment items to the factory preset values, press A/T to select "Reset", and then press

ENTER.

(D22


Use Fine Motion Enhanced to view fast-action video more clearly.

On. For obtaining a clearerimage.

Off: Normal image.

= "FineMotion Enhanced" may cause image noise. If this occurs, turn the function "Off".

Produces a clearer video image.

Auto: Automatically adjusts the level of noise reduction.

High/Middle/Low: Select a desired level for viewing a clearer video image.

Off: No adjustment.

= "Digital Noise Reduction" is not available during PC format input.

Automatically adjusts the image contrast according to the scene.

On. Automaticallyadjusts the image contrast.

Off" No adjustment.

Adjusts the differences of picture tones between bright parts and dark parts. The adjustment range of the gamma can be set to a maximum of +2 and a minimum of-2 by pressing 4 or _..

Provides high quality images with minimal dot crawl and cross color noise.

Slow.

For still images.

Standard" Normal adjustment.

Fast" For moving images.

= "3D-Y/C" is available for input signal from Composite Video and analog broadcasts (air and cable).

Adjusts on-screen black level to your preferred level.

High: The black level gets brighter.

Low" The black level gets darker.

= "Black Level" is available for input signal from Composite

Video, S-Video, Component 480i and analog broadcasts

(air and cable).

Automatically detects a film-based source (originally encoded at 24 frames/second), analyzes it then recreates each still film frame for high-definition picture quality.

Advanced(High}/Advanced(Low)" Select a desired level to remove jerkiness from film contents.

Standard: Detects, analyzes, converts film source.

Off" Normal viewing mode.

= "Film Mode" does not function when you set AV MODE to

"GAME".

= "Standard" does not function when channel display shows an input signal resolution of 480p, 720p, or 1080p.

= "Film Mode" is not available during PC format input.

For viewing a video in monochrome.

On. For viewing in monochrome.

Off" Normal color.

The brightness level range of the OPC sensor's automatic adjustments can be set according to your preferences.

The adjustment range of the OPC sensor can be set to a maximum of +16 and a minimum of -16.

Max,"-15 through +16

Min.: -16 through +15

= The "Range of OPC" settings are active only when "OPC" is set to "On".

= The maximum setting cannot be set to a smaller number than the minimum setting.

= The minimum setting cannot be set to a bigger number than the maximum setting.

= Depending on the brightness of the surrounding light, the

OPC sensor might not operate if the adjustment range is small.

Q23


You can adjust the sound quality to your preference with the following settings.

Example

[ _ Audio ]

Power control settinc

Example allows you to save energy.

_ Power Control

-FAVORITECH

®®©®

--

1 Press MENU to display the MENU screen, and then press _1/1_ to select "Power Control".

2 Press A/V to select a specific adjustment item,

//I

3 Press A/T (or 4/_) to select the desired setting, li..........

.A" and then press ENTER.

and then press ENTER.


1 Press MENU to display the MENU screen, and then press 4/1_ to select "Audio".

2 Press A/Y to select a specific adjustment item.

o Select "Surround" or "Bass Enhancer" and then press

ENTER to set each item.

3 Press A/T (or 4t/),,) to select the desired setting, and then press ENTER.


This function allows you to set the Power Saving level in order to decrease the power consumption and increase the backlight lifespan.

Standard: Optimizes power reduction based upon video content. When set to "Standard", "_" appears on the screen.

Advanced: Optimizes power reduction based upon video content and engages OPC. When set to "Advanced",

....

appears on the screen.

Off: This function does not work.

Treble

Bass

Balance

For weaker treble For stronger treble

For weaker bass For stronger bass

Decreaseaudio from Decrease audio from the right speaker the left speaker

= Audio menu is grayed out when "Output Select" is set to

"Variable". (See page 29.)

= For resetting all Audio adjustment items to the factory preset values, press h,/T to select "Reset", press ENTER, press _1/1_ to select "Yes", and then press ENTER.

The surround function produces Surround effect from the speakers.

On: Makes it possible to enjoy natural, realistic surround sound.

Off: Outputs the normal sound.

= "Power Saving" does not function when you set AV MODE to "AUTO" or "DYNAMIC (Fixed)".

= You cannot select a different Power Saving item for each

AV MODE.

When "Power Saving" is set, the "OPC" settings for all AV

Modes will automatically change.

--If you set "OPC" to "On" when "Power Saving" is set to "Standard", then the "Power Saving" setting will change to "Advanced".

--When you change the "Power Saving" setting from

"Advanced" to "Off" or to "Standard", "OPC" will be set to "Off".

--"AUTO" and "DYNAMIC (Fixed)" will remain set to "Off".

= When "Power Saving" is set to "Standard" or "Advanced", the Power Saving leaf icon appears to the left of "OPC" in the Picture menu screen.

= You can select Power Saving by pressing POWER

SAVING on the remote control unit. (See page 18.)

When set to "Enable", the power will automatically shut down if there is no signal for 15 minutes.

o You can choose Surround by pressing SURROUND on the remote control unit. (See page 16.)



= For some discs, setup may be required on your DVD player. In this case, please refer to the operation manual of your DVD player.

= When it is 5 minutes before the power shuts down, the remaining time will start to keep appearing every minute.

= "Disable" is the factory preset value.

= When a TV program finishes, this function may not operate.

This function allows you to enjoy bass-enhanced

On: Bass Enhancer function is on.

Off: Normal sound.

sound.



@- 24

When set to "Enable", the power will automatically shut down if there is no operation for 3 hours.

= When it is 5 minutes before the power shuts down, the remaining time will start to keep appearing every minute.

= "Disable" is the factory preset value.


Example

FREEZE

0

¢

-FAVORITE

®®@@

CH

AQUOS

--

MENU

@

1 Press MENU to display the MENU screen, and then press 41/1_ to select "Setup".

2 Press A/V to select a specific adjustment item, and then press ENTER. o When you select "EZ Setup", "OHSetup", "Parental

CTRL" or "Reset",you can enter the 4-digit secret number here. See page 26 for setting a secret number.

3 Press A/T (or 4t/1_) to select the desired setting, and then press ENTER.

4 Press MENU to exit.

You can run EZ Setup again, even after setting up the preset channels.

Language: Select from among 3 languages (English,

French and Spanish).

TV Location: Select "Home" or "Store" for the location where you plan to install the TV. This product qualifies for ENERGY STAR V3.0 in Home mode default setting.

Home: "Power Saving" is set to "Advanced", and AV MODE is set to "S]ANDARD'L

Store: "Power Saving" is set to "Off" and AV MODEis set to

"DYNAMIC(Fixed)".Picture Reset and FeatureDemo carl be set.

Picture Reset: AV MODE will be set to "DYNAMIC(Fixed)" regardlessof whether Picture Reset is "On" or "Off". If you select "On", AV MODEwill be resetto "DYNAMIC(Fixed)" if there is no operation for 30 minutes.When "Off" is selected, AV MODEwill be set to "DYNAMIC(Fixed)".

Feature Demo: When "On" is selected, afler all the settings are completed, the FeatureDome screen is displayed if there is no operation for several minutes.

® ENERGYS]AR qualification is based on AV MODE

Air/Cable: Make sure what kind of connection is made with your TV when selecting "Air" or "Cable".

OH Search: Channel auto search makes the TV look for all channels viewable in the set area.

o See "Initial Setup" on page 15 for setting each item.

If no channel is found, confirm the type of connection made with your TV and try "EZ Setup" again.

If you select "Analog Search Start" and initiate the channel search, the CH Memory for Cable Digital will be deleted.

If initial setup does not memorize all the channels in your region, follow the instructions below to manually memorize the channels.

Air/Cable: Make sure what kind of connection is made with your TV when selecting "Air" or "Cable".

OH Search: Channel auto search makes the TV look for all channels viewable in the set area.

OH Memory: You can select the channels to skip in each

ANALOG (Air), ANALOG (Cable), DIGITAL (Air) and

DIGITAL (Cable).

On: Skips channels. (Channelselection disabled using CH

A/V,) off: Does nol skip channels,(Channelselectionenabled using

CHA/V.)

Remove Scrambled OH: This function makes the TV look for and then delete digital cable channels that are scrambled and so unavailable in the set area. The process may take more than 20 minutes.

Yes: Starts to remove scrambled channels.

No: This function does not work.

See "Initial Setup" on page 15 for setting each item.

If no channel is found, confirm the type of connection made with your TV and try channel search again.

If you select "Analog Search Start" and initiate the channel search, the CH Memory for Cable Digital will be deleted.

In order to receive digital air broadcasts, you need a digital broadcast antenna.

You can confirm the antenna configuration through the "Antenna Setup-

DIGITAL" screen.

If necessary, adjust the direction of the antenna to obtain the maximum signal strength.

Signal Strength: The signal strength of DIGITAL channel is displayed. The signal information is based on the current channel.

Channel Strength: Input the 2-digit channel number to check the signal strength of the selected channel.

Make sure the signal is strong enough for each channel.

,_ This function is availablefor DIGFrAL(Air)only.

This setting allows you to skip the HDMI or PC-IN Input

("Input 4 (PC)", "Input 5 (HDMI)", "Input 6 (HDMI)",

"Input 7 (HDMI)" and "Input 8 (HDMI)") on the Input

Selection operation.

Yes: Skips the input.

No: Does not skip input.

Lets you set the input terminal displayed when using the INPUT SOURCE menu or channel display. Press

A/V/411/I_ to select the new name for the input mode.

You cannot change labels if the INPUT SOURCE is TV.

@25


For adjusting a picture's horizontal and vertical position.

H=Pos." Centers the image by moving it to the left or right.

V=Pos." Centers the image by moving it up or down.

o For resetting adjustments to the factory preset values, press A/T to select "Reset", and then press ENTER.

When connecting a PC to the HDMI terminal, the image position will be automatically adjusted.

It cannot be manually adjusted.

The screen position variable ranges depend on the View

Mode or the signal type. The ranges can be seen on the position-setting screen.

Adjustments are stored separately according to input

SOUrCe,

You can also select a language from the Setup menu.

Select from among 3 languages: English, French and

Spanish.

If complex adjustments are made and the settings cannot be restored to normal, you can reset the settings to the factory preset values.

1 "Return to the factory preset values" displays on the screen.

o If you have already set the Secret No., input the 4-digit secret number here.

2 Select "Yes".

o "Now, TV will restart automatically. OK?" displays on the screen.

3 Select "Yes".

o "Now initializing..." displays on the screen and blinks.

After the reset has been completed, the power shuts off and then comes back on. The screen will have returned to its original settings.

The Channel Setup settings will not be changed.

The Language settings will not be changed.

The Secret number settings will not be changed.

The TV Location settings will not be changed.

Allows you to use a secret number to protect certain settings from being accidentally changed.

iMPORTANT:

Three conditions must be met to enable the V-Chip (see pages 27 to 28):

1.

Secret No. is registered.

2.

V-Chip/V-Chip (DTV Only) settings have been made.

® The "V-Chip (D_/Only)" will only be selectablewhen a new rating system carl be downloaded via digital broadcasting in the

U.S.

3.

"Status" is set to "On".

== New Secret No,

You can set and change the secret number by using

0-9.

Input Secret No." When you change the secret number, enter the old 4-digit secret number here. The cursor moves to "New Secret No.".

New Secret No." When you set the new secret number, enter the new 4-digit secret number here. The cursor moves to "Reconfirm".

Reconfirm: Enter the same 4-digit number you set in

"New Secret No.".

Secret No. Clear

You can clear your secret number.

Yes" Your secret number is cleared.

No" Your secret number is not cleared.

As a precautionary measure, make a note of your secret number and keep it in a familiar place.

If the secret number is cleared, the Status setting automatically sets to "Off". "V-Chip" and "Status" will not be selectable from the menu.

Used to enable or disable the parental control function.

This function will not be selectable from the menu if you do not first configure your secret number.

On. Enables ParentalCTRL.

Off: DisablesParentalCTRL.

(D26

On=Screen Display Menu

TV Parental Guidelines

Example

V-CHIP is an electronic filtering device built into your

TV. This tool gives parents a great degree of control over broadcasts accessed by their children. It allows parents to select programs judged suitable for child viewing while blocking ones judged not suitable. It does so automatically once you activate the V-CHIP feature in your TV. "V-Chip" and "Status" will not be selectable from the menu if you do not first configure your secret number.

= The U.S. has two rating systemsfor viewing content: TV

ParentalGuidelines and movie ratings.

= The TV ParentalGuidelineswork in conjunction with the

V-CHIP to help parents screen out inappropriatetelevision shows from their children.

= Movieratings are used for original movies rated by the

Motion Picture Association of America (MPAA)as watched on cable TV and not edited for television.The V-CHIP can also be set to block MPAA-rated movies.

= The setting automatically enters "Block" for any ratings below your selection.

= If Status is not set to "On", the configuration settings will not work.

m MPAA (Voluntary movie rating system}

Example

Press A/V to adjust the item to your desired position.

"_" indicates the item is blocked. Press MENU to exit.

Suggested age

TV-Y: All children.

TV=Y7: Directed to older children.

TV-G: General audience.

TV=PG: Parental Guidance suggested.

TV-14: Parents strongly cautioned.

TV=MA: Mature audience only.

Example

Press A/Y to adjust the item to your desired position.


G" General audiences. All ages admitted.

PG" Parental guidance suggested. Some material may not be suitable for children.

PG-13" Parents strongly cautioned. Some material may be inappropriate for children under 13.

R" Restricted. Under 17 requires accompanying parent or adult guardian (age varies in some jurisdictions).

N0-17: No one 17 and under admitted.

X" X is an older rating that is unified with NC-1 7 but may be encoded in the data of older movies.

= Voluntary movie rating system only uses an age-based rating.

When setting an individual content-based rating item:

1 Press I_ or ENTER to access blocked content items from the currently selected age-based rating item.

2 Press A/T to select an individual item, and then press ENTER to unblock it ("_" is removed). Repeat the same steps for the other items.

3 Press 4 or RETURN to register after all individual content rating items are set.

Content

FV: Fantasy violence.

V: Violence.

S: Sexual situation.

L: Adult language.

D: Sexually suggestive dialog.

TV-Y

TV-Y7

TV-G

TV- PG

TV-14

TV-MA

[]

X

[]

X

[]

[]

X

X

[]

X

[]

[]

X

X

[]

X

[]

[]

X

X

[]

X

[]

[]

X

[] : The content rating can be set, but this rating is not normally broadcast by TV stations.

X : Content rating can be set.

Q27


Canadian Rating Systems (Canadian English ratings and Canadian French ratings) o The TV rating systems in Canada are based on the

Canadian Radio-Television and Telecommunications

Commission (CRTC) policy on violence in television programming.

While violence is the most important content element to be rated, the structure developed takes into consideration other program content like language, nudity, sexuality and mature themes.

When setting the V-CHIP on the Canadian system you can choose either the Canadian English ratings or the

Canadian French ratings.

[] Canadian English Ratings

Example

[] Canadian French Ratings

Example

Can. English Ratings



E" Exempt: Includes news, sports, documentaries and other information programming; talk shows, music videos, and variety programming.

O" Children: Intended for younger children under the age of 8 years. Pays careful attention to themes that could threaten their sense of security and well-being.

08+: Children over 8 years old: Contains no portrayal of violence as the preferred, acceptable, or only way to resolve conflict; nor encourage children to imitate dangerous acts which they may see on the screen.

G" General: Considered acceptable for all age groups.

Appropriate viewing for the entire family, contains very little violence, physical, verbal or emotional.

PG" Parental Guidance: Intended for a general audience, but may not be suitable for younger children (under the age of 8) because it could contain controversial themes or issues.

14+" Over 14 years: Could contain themes where violence is one of the dominant elements of the storyline, but it must be integral to the development of plot or character.

Language usage could be profane and nudity present within the context of the theme.

18+" Adults: Intended for viewers 18 years and older and might contain depictions of violence, which while related to the development of plot, character or themes, are intended for adult viewing. Could contain graphic language and portrayals of sex and nudity.


"It" indicates the item is blocked. Press MENU to exit.

E" Exempt programming.

G" General: All ages and children, contains minimal direct violence, but may be integrated into the plot in a humorous or unrealistic manner.

8arts+" General but inadvisable for young children: May be viewed by a wide public audience, but could contain scenes disturbing to children under 8 who cannot distinguish between imaginary and real situations.

Recommended for viewing with parent.

13arts+" Over 13 years: Could contain scenes of frequent violent scenes and therefore recommended for viewing with parent.

16arts+" Over 16 years: Could contain frequent violent scenes and intense violence.

18aria+" Over 18 years: Only for adult viewing. Could contain frequent violent scenes and extreme violence.

[] How to temporarily release the V-CHIP BLOCK

When the V-CHIP BLOCK is working and censors a broadcast, "V-CHIP HAS BEEN ACTIVATED." displays.

1 Press ENTER while the V-CHIP is working, and then the secret number setting menu displays.

2 Input the 4-digit secret number by using 0-9. At this time V-CHIP BLOCK temporarily releases.

[] Reactivating the temporarily released V-CHIP

BLOCK

You can reactivate the temporarily released V-CHIP

BLOCK as shown below.

Select "Status" setting from the Parental CTRL menu to reactivate BLOCK. (See page 26.)

Select "V-Chip" setting ("MPAA", "TV Guidelines", "Can.

English Ratings" or "Can. French Ratings") from the

Parental CTRL to reactivate BLOCK. (See pages 27 to 28.)

Switch off the TV power.

Performing any of the three above will activate the V-CHIP

BLOCK.

Q28


Example

Option

INPUT

@0

VOL CH

FLA$H_C_

1 Press MENU to display the MENU screen, and then press 4/1_ to select "Option".

2 Press ,&/V to select a specific adjustment item and then press ENTER.

3 Press A/T (or 4/1_) to select the desired setting, and then press ENTER.


• Skip this step for "Audio Only".

When listening to music from a music program, you can turn the screen off and enjoy audio only.

On: Audio is output without screen image.

Off: Both screen images and audio are output.

o The screen image will return to normal when a button

(except those for audio adjustment, such as VOL, MUTE,

SURROUND, AUDIO)is pressed.

If the image does not come in clearly from the external equipment connected to INPUT 1 or INPUT 2, you may need to change the input signal type setting on

[] INPUT 1

Select the input signal type from the list below:

Auto/COMPONENT/ViDEO

[] INPUT 2

Select the input signal type from the list below:

Auto/COMPON ENT/S-TERMINAL

If the selected signal type is incorrect, images are not displayed at all or are displayed without any color.

Refer to your external equipment operation manual for the signal type.

= If you set INPUT 1 or 2 to Auto, the TV will automatically select the input signal.

Setting INPUT 1 or 2 signal selection to "Auto" when other equipment is connected will result in the following connection priority.

INPUT 1:

(_) COMPONENT VIDEO

(_) VIDEO

INPUT 2:

(_) COMPONENT VIDEO

(_) S-VIDEO

To watch an HDMI or PC-IN equipment image, select

"INPUT5", "INPUT6", "INPUT7" or "INPUTS" from

INPUT SOURCE menu using INPUT on the remote control unit or on the TV.

Auto View:

Enable: To use View Mode based on signal recognition,including an HDMIsignal.

Disable: No function.

Refer to your external equipment operation manual for the signal type.

When connecting an HDMI-DVl conversion adapter/cable to the HDMI terminal, the image may not come in clearly.

Different sound sources sometimes do not have the same volume level, such as a program and its commercial breaks. The Automatic Volume Control

(Auto Volume) reduces this problem by equalizing levels.

This function emphasizes speech against background noise for greater clarity.

Allows you to select what controls the audio output.

Fixed: Sound via speaker is adjusted with VOL +/on the remote control unit or VOL +/on the TV.

Sound via the AUDIO OUTPUT terminal is not adjustable and outputs at a consistent level.

Variable: Sound via the AUDIO OUTPUT terminal is adjusted with VOL+/-

VOL+/on the TV.

on the remote control unit or

Sound via speaker is muted.

You can select whether to use transition effects when changing channels.

Yes: A transitioneffectis usedwhen the channelis changed.

No: No function.

@29


Select the video signal system compatible with your equipment from the list below:

Auto/NTSC/PAL-M/PAL-N o "Color System" can only be set for the INPUT 1 VIDEO,

INPUT 2 S-VIDEO and INPUT 3 VIDEO.

If you have already set the Secret No., input the 4-digit secret number here. See page 26 for setting a secret number.

This function locks the operation buttons on the TV and the remote control.

Off. No adjustment.

RC Control Lock: All buttons on the remote control are locked.

Button Control Lock: All buttons on the TV, except

POWER, are locked.

This function allows you to adjust the closed caption screen appearance to suit your preference.

You can adjust 7 items: "Caption Size", "Font

Style", "Foreground Color", "Foreground Opacity",

"Background Color", "Background Opacity" and

"Character Edge".

Example:

Selectable items available for "Font Style".

Default: The font specified by broadcasting station or default font.

Type 0: Proportionalfont used in the MENU screen.

Type 1: Monospaced with serifs.

Type 2: Proportionally spaced with serifs.

Type 3: Monospaced without serifs.

Type 4: Proportionally spaced without serifs.

Type 5: Casual font type.

Type 6: Cursive font type.

Type 7: Small capitals.

For resetting adjustments to the factory preset values, press A/T to select "Reset", and then press ENTER.

The default value depends on the broadcasting station.

o To unlock the buttons on the remote control by using the control panel of the main unit (see page 20):

(_ Press MENU to display the MENU screen, and then press VOL +/to select "Option".

(_ Press CHA/V to select "Operation Lock Out", and then press INPUT,

(_ Press CHA/V to select "Off", and then press INPUT.

(_ Press MENU to exit.

To unlock the buttons on the TV, press MENU on the remote control, and then select "Off" in "Operation Lock

Out".

This function allows you to program 4 favorite channels, in 4 different categories.

By setting the favorite channels in advance, you can select your favorite channels easily.

To register your favorite channel:

Select "Register" and then press ENTER. Press A/Y/4/ to select the position in the category, and then press

ENTER to register.

To delete your favorite channel:

Select "1 Data Clear" and then press ENTER. Press

A/Y/41/_ to select the channel you want to delete, and then press ENTER. Select "Yes" and then press ENTER.

To delete all the favorite channels, select "All Data Clear".

This function allows viewing of digital closed caption information for the digital broadcast program being viewed.

Before setting the channel, select the channel you want to register as a favorite channel.

You can display the "Favorite CH" screen by pressing

FAVORITE on the remote control.

This list is not displayed for analog broadcasts or external input audio/video.

This information is not included in CC1, CC2, Text1, or

Text2, and is not displayed in a list.

Select the CH display when changing channels for digital broadcasting.

Yes: "Program Info."displays.

No: "Program Info."does not display.

This function displays the elapsed game time so you do not lose track of the time. To display the elapsed time, select "GAME" for the AV MODE before starting the game.

On: The elapsed time is displayed every30 minutes when you switch to GAME mode in external input mode.

Off: No adjustment.

You can select the image from several types of demo mode.

120Nz Demo 1/120Nz Demo 2/10 bit Demo/Feature

Demo/Auto Play

If you select "Auto Play", you need to set playback type.

Continuous: Play Demos continuously.

10 rain.: Play Demos every 10 minutes.

20 rain.:

Play

Demos every 20 minutes.

This function will be canceled when you press EXIT on the remote control unit.

When "Demo Mode" is set to "Feature Demo", pressing

FREEZE pauses/restarts demo.

"Demo Mode" may not be selected depending on input signal type.

"Demo Mode" may be automatically canceled depending on input signal type.

(D30


Example

Digital Setup

This function allows software updates by inserting a

USB memory device with the update file into the

SERVICE terminal on the TV.

To check for the availability of a software update, visit www.sharpusa.com.

If you have any questions, please call 1-800-BE-SHARP (800-237-4277).

-FAVORITECH

®®@@

--

1 Press MENU to display the MENU screen, and then press 41/_ to select "Digital Setup".

2 Press A/V to select a specific adjustment item, and then press ENTER.

3 Press A/T (or 4/_) to select the desired setting, and then press ENTER.


You can output digital audio to an AV amplifier or similar device whose DIGITAL AUDIO INPUT terminal is connected to the DIGITAL AUDIO OUTPUT terminal on the TV. Please select an audio output format compatible with the audio format of the program you are watching and the equipment connected.

PCM: The optical output terminal outputs audio signal in PCM form. Ifyour digital audio systemdoes not support Dolby Digital,select "PCM".

Dolby Digital: The optical output terminal outputs audio signal in Dolby Digitalform. It reproduces sound from surround program of digital.

i ®@O

® Q

CO

o ,N?il°

-FAVORITECH

®®@@

-o Do not remove the USB memory device or unplug the AC cord while the software is being updated.

Be sure to properly follow the whole procedure described below, step by step. Otherwise, for example, the TV cannot read the data in the USB memory device and software updating will fail.

1 Insert the USB memory device with the update file into the SERVICE terminal on the TV.

The current version of the TV software is displayed.

2

Press MENU to display the MENU screen, and then press 4/_ to select "Digital Setup".

3

Press A/Y to select "Software Update", and then press ENTER.

If you have already set the Secret No., go to step 4.

[ _ Digital Setup ]

Software update ]

4

Input the 4-digit secret number by using 0-9.

[ _ DigitalSetup ]

@31


5

Press ENTER to start checking the data in the

USB memory device.

Press ENTER to start updating.

The screen becomes dark for a while until the update screen can be displayed.

Please wait for the update screen to appear. Do not unplug the AC cord.

6 During the data checking, "Checking" blinks.

!!

Example

The current version of the %/software and the version of the update file on the USB memory device are displayed.

To update the TV software with the update file, select "Yes", and then press ENTER.

Example

• Do not remove the USB memory device or unplug the AC cord while the software is being updated.

8

When the software is successfully updated, a screen is displayed indicating that the update process is completed.

After this screen is displayed, the TV automatically turns off and then turns on again.

Example

If the USB memory device is not properly installed or the correct update file cannot be found on the USB memory device, an error message is displayed.

Check the file on the USB memory device, and then reinsert the USB memory device correctly.

• If the update has failed, check the file in the USB memory device and try Software Update again.

9 After the screen shown below is displayed, press

ENTER.

10 Remove the USB memory device.

Q32

Other Viewing Options

You can operate the connected AV products (AV receiver, cable box, SAT tuner, DTV, VCR, DVD, LD) using the presetting manufacturer function of your remote control unit.

1

2

3

SOURCE

V_R

_D

AUoDIO

LIGHT

7

8

Po

Presetting manufacturer codes

1 Press FUNCTION until the LED for your device lights up.

2

After the LED for your device lights up, press

FUNCTION and DISPLAY at the same time to enter the code registration mode. The LED will blink.

3

Press 0-9 to enter the manufacturer page 34.) code.

(See

Preset mode is finished once the LED no longer lights up.

4

After registering the code, the LED will stop blinking then turn off after one second. (If you perform an incorrect operation, the LED will blink quickly then turn off.)

To operate the connected equipment, press

FUNCTION to select the LED for your device. (VCR,

AUDIO, CBL/SAT (cable converter) or DVD.) The

LED lights up, and the remote control unit button will function as follows.

+ When you operate VCR or DVD, press INPUT to select the terminal connected to your device.

+ CABLE and SAT cannot be selected at the same time.

1 SOURCE POWER

+Turns the connected equipment power on and off.

2 "14

+ Rewinds the tape and allows picture search. (VCR)

+ Hold down to go in reverse. (DVD)

3 REC

+ Starts recording. (VCR)

4

144

+ Pressing quickly once takes you to the start of the chapter currently playing. Each time you press it, you move back to the start of the previous chapter. (DVD)

5 0-9 (CBL/SAT), • (DOT) (SAT)

+ Press a button (or buttons) that corresponds to the channel that you wish to watch.

+ Starts playback. (VCR, DVD)

+ Rapidly advances the tape and allows picture search.

(VOR)

• Hold down to fast forward.

(DVD)

8|1

,, Sets pauses and still pictures. (VCR, DVD)

9

m

+ Stops the tape transport. (VCR)

+ Playback stops when pressed. With some DVD players, pressing the button twice may open the disc tray. (DVD)

+ Pressing quickly once takes you to the start of the next chapter. Each time you press it, you move ahead to the start of the next chapter. (DVD)

11 FLASHBACK

+ Pressto switch between the current channel and the channel you were watching immediatelybefore. Some manufacturersdo not preset FLASHBACK.(CBL)

12 CHA/V

+ PressCH/X or CHV to tune in to a higher or lower channel, (CBL)

+ Pressto select the channel of the TV tuner on the VCR.

(VOR)

13 MENU

+ When this button is pressed, the DVD menu will display.

(DVD)

14 A/T/4/I_, ENTER

+ A/T/4/I_: Press the button to select items on the SAT

GUIDE screen or SAT MENU screen. (SAT). Press the button to select items on the DVD menu screen. (DVD)

+ ENTER: Press to activate the selected function. (SAT,

DVD)

@33

Other Viewing Options

Manufacturer codes

VCR BRAND

Akai

Audio

Broksonic

Canon

Capehart

Craig

Curtis Mathis

Daewoo

DBX

Dynatech

Emerson

Fisher

Funai

G.E.

Goldstar

Hitachi

Instant Replay

JC Penney

JVC

Kenwood

LIoyds

Magnavox

Magnin

Marantz

Memorex

Minolta

Mitsubishi

Montgomery Ward

Multitech

NEC

Panasonic

Pentax

PNco

PNips

Pioneer

QUASAR

RCA

Realistic

Samsung

Sanyo

Scott

Sears

Sharp

Shintom

Sony

Sound Design

Sylvania

Symphonic

Tatung

Teac

Teknika

Thomas

TMK

Toshiba

Video Concepts

Yamaha

Zenith

REMOTE CONTROL CODE

NUMBER

25, 26, 37

15, 22, 30

32

04

34

10, 31

O4

34

15, 22, 30

29

21, 32, 35

09, 10, 11

28, 29

04

24

06, 47

04

04, 06, 24, 30

15, 41,42, 53

14, 15

29

04, 05, 08

31

3O

04, 10, 24, 29

O6

17,

02,

29

18,39,40,48

43

05,

04,

04,

46

O4

06,

15,

04,

22,30

44,45,49,50

06

06

05,08

07,33,51

01,

23,

10,

20

02,10,24

31

14,52

06,

01,

36

11,24

02,03

12,

29

05,

29

13, 38

08

15

15,

27,

29

29

29

21

19, 20

30

15,

16

29,30

DVD/BD/LD BRAND

Denon

JVC

Kenwood

Magnavox

Marantz

MitsubishJ

Panasonic

Philips

Pioneer

Proscan

RCA

Samsung

Sharp

Sony

Toshiba

Yamaha

Zenith

REMOTE CONTROL CODE

NUMBER

02

09

21

04

04

06

02,22

04,23

08,11,20

03

03,24

07,12

01,!0

05,25

04

02

04

CATV/SAT BRAND

Anvision

Cable Star

Eagle

General Instrument

Jerrold

Magnavox

Motorola

NEC

Oak Sigma

Panasonic

Philips

Pioneer

Randtek

RCA

Scientific Atlanta

Sony

Viewstar

Zenith

REMOTE CONTROL CODE

NUMBER

04,05

04,05

O5

02,03,07,12,13,14,

19,22

02,03,07,12,13,14,

22,31,32,33,34,35,

36,37,38,39,40

04,05,09,14,17,!8,

20,21,24,25

47

42

8

16,23

04,05,09,15,17,!8,

20,21,24,25

08,10,29,30,43",46

04,05

16,27,44",45"

01,26

28

04,05,09,!5,17,!8,

20,21,24,25

06,41

Numbers marked with * are SAT codes, all others are

CATV codes.

Sharp

AUDIO BRAND

REMOTE CONTROL CODE

NUMBER

0!

Q34

Using AQUOS LINK

What's AQUOS LINK?

• Using the HDMI CEC (Consumer Electronics Control) protocol, with AQUOS LINK you can interactivelyoperate compatible system equipment (Blu-ray disc equipment, AV amplifier, DVD).

By connecting AQUOS LINK-compatible devices with HDMI-certified cables to the TV, you can control a recorder or AV amplifier using the remote control of the TV.

AQUOS LINK allows you to operate the HDMI-connected equipment with one remote control.

Example*

,>_m

HDMI certified cable

(commercially available)

__.J

AQUOS LINK-compatible

Audio system

Optical fiber cable

I

(commercially available)

HDMl-certified cable

* You can use the INPUT 5,L_

6, 7 or 8 terminal.

AQUOS BD Player

TV o Point the remote control toward the TV, not to connected HDMI equipment.

o Video noise may occur depending on the type of HDMI cable used. Make sure to use an HDMI-certified cable.

o Up to 3 pieces of HDMI recording equipment and one AV amplifier can be connected using this system.

o These operations affect the HDMI equipment selected as the current input source. If the equipment does not operate, turn on the equipment and select the appropriate input source using INPUT.

You can operate AQUOS LINK-compatible devices with the remote control unit when the FUNCTION of the remote control unit is set to TV.

SOURCE

2 v&_%,0

LIGHT

REC STOP and OPTION buttons will function only when AQUOS LINK is used,

VOL

INPUT FLASHBACK

@©

OH

[] One Touch Play

While the TV is in standby mode, it automatically turns on and plays back the image from the HDMI source.

[] One Touch Recording

Press REC while you are viewing a broadcast received with the AQUOS

LINK-compatible recorder. The AQUOS LINK automatically recognizes the connected HDMI device and starts recording.

[] Single remote control

The AQUOS LINK automatically recognizes the connected HDMI device and you can control the TV and the devices as if using a universal remote control.

[] Control the AQUOS LINK=compatible audio system

Set the volume of AQUOS LINK-compatible audio system.

o The above description is an example of the AQUOS LINK function.

o The steps in "AQUOS LINK Setup" on page 36 need to be completed beforehand.

o Refer to this operation manual and the operation manual of the AQUOS LINK device to be used with this TV.

Q35

Using AQUOS LiNK

i O

[ FREEZE

@

MENU

When multiple AQUOS LINK-compatible devices are connected, this function allows you to set the recorder for recording when you press REC on the TV's remote control unit.

Press ,&/V to select the recorder for recording.

Example

1

Press MENU to display the MENU screen, and then press 4/!_

to select "Option".

2

Press A/V to select "AQUOS LINK Setup", and then press ENTER.

3

Press ,&/V to select a specific item, and then press

ENTER.

4

5

Press A/T (or 4t/1_ ) to select the desired setting, and then press ENTER.

Press MENU to exit.

Selecting Recorder

Example : when connecting AQUOS LINK-compatible recorder system

via AQUOS MNK-compatible Audio

Select AQUOS LINK Control to disable AQUOS LINK function even when an AQUOS LINK-compatible HDMI device is connected to the TV. This function prevents the device from starting to operate unexpectedly.

Enable: You can operate AQUOS LINK-compatible equipment.

Disable: AQUOS LINKfunction does not work.

AQUOS LINK Control

Selecting Recorder

When an AQUOS LINK-compatible audio system or other equipment is connected between the TV and recorder, "Sub" is displayed.

If this is activated, the One Touch Play function is enabled.

Yes: While the TV is in standby mode, it automatically turns on and plays back the image from the HDMI source.

No: This function does not work.

This function allows easy one-touch recording of the program being viewed on the TV to AQUOS LINKcompatible equipment with a recording function by simply pressing REC on the remote control.

SOURCE LIGHT

GE) (Z) dE)

REC

Prepare the connected AQUOS LINK-compatible recorder for recording.

Check the following items.

o Make sure that the antenna cable is connected.

o Check that there is sufficient available space on the recording media (HDD, DVD, etc.).

o On the TV, use "AQUOS LINK Setup" and "Selecting

Recorder" to select the equipment for recording.

o By default, the recorder connected to INPUT 5 is selected for recording.

1 Press REC to start recording.

o When you are viewing a broadcast received with the AQUOS LINK-compatible recorder selected in

"Selecting Recorder", recording to the AQUOS recorder of the broadcast being viewed starts.

o When you are viewing a broadcast received with equipment other than the AQUOS LINK-compatible recorder selected in "Selecting Recorder" or other external input equipment, pressing REC on the remote control does not start recording.

2 Press REC STOP to stop recording.

Q36

Using AQUOS LiNK

AQUOS LINK allows you to operate the HDMIconnected equipment with one remote control.

SOURCE LIGHT

Recorder EPG

Press I_ to start playing back a title.

= The last played program is played back. You can use the following buttons during broadcast viewing.

SOURCE

POWER

_!1_

I_

1_

[]

| Ill

Turns the power of the HDMI connected devices on and off.

Hold down to go in reverse.

Starts playback.

Hold down to fast forward.

Playback stops.

Sets pauses and still pictures.

Pressing quickly once takes you to the start of the chapter currently playing. Each time you press it, you move back to the start of the previous chapter.

Pressing quickly once takes you to the start of the next chapter. Each time you press it, you move ahead to the start of the next chapter.

o The buttons M_I/II,P,I do not function with the following

Blu-ray disc players currently available.

- BD-HP20U, BD-HP50U

--

SAnG

......

FREEZE

O

VOL

FAVORITECH

®@®@

CH

--

MENU

O

E

F'B1

You can call up the AQUOS LINK-compatible recorder's EPG and preset timer recordings using the

TV's remote control.

1 Press OPTION to display the AQUOS LINK MENU screen.

2 PressA/V toselect pressENTER.

o The recorder's EPGis displayed.

3 Select the program to record.

o You can use A/Y/4/I_, ENTER, RETURN, EXIT and the coloured buttons.

o This function works only when an AQUOS LINK-compatible recorder is connected.

o Refer to the operation manual of the recorder for details.

Q37

Using AQUOS LiNK

This section explains how to play back a title in the

AQUOS LINK-compatible equipment.

1 Power on the AQUOS LINK-compatible equipment, and select appropriate external input.

2

Press OPTION to display the AQUOS LINK MENU screen.

3

Press A/V to select "Top menu/title list", and then press ENTER.

= The title list data from the connected AQUOS LINKcompatible equipment displays.

4

Select the title with A/V/4/_, to start playback.

and then press

1

Press OPTION to display the AQUOS LINK MENU screen.

2

Press A/V to select "Sound mode change", and then press ENTER.

o The sound mode changes each time you press ENTER.

o Refer to the operation manual of the AQUOS LINKcompatible audio system for details.

o This function works only when AQUOS LINK-compatible equipment is connected.

You can call up a setup menu from the connected

AQUOS LINK-compatible equipment.


2 Press A/V to select "Setup menu", and then press

ENTER.

,, The setup menu of the AQUOS LINK-compatible equipment is displayed.

You can switch the media (HDD or DVD) for playback or recording on the AQUOS LINK-compatible recorder.


2 Press A/V to select "Media change", and then press ENTER.

3 Select the desired media such as DVD or HDD.

o The Media type toggles each time you press ENTER in

"Media change".

• Select the media to be operated by the player.

= Depending on the status of the equipment (recording or in standby mode, etc), the setup menu will not be displayed.

o The setup menu will not be displayed with the player

BD-HP20U currently available.

You can select to listen to the TV sound only from the

AQUOS LINK-compatible audio system and manually change its sound mode.


2 Press A/V to select "By AQUOS AUDIO SP", and then press ENTER. o The sound from the TV speaker is muted and only the sound from the AQUOS LINK-compatible audio system is audible.

o You can use VOL+/and MUTE.

Select "By AQUOS SP", and then press ENTER to listen to the TV sound.

If multiple HDMI devices are connected in a daisy chain, you can specify which device to control here.


2 Press A/V to select "Model select", and then press ENTER. The HDMI device toggles each time you press ENTER.

Q38

Using a PC

You can select the screen size.

I

i@®®

OURCE LIGHT

C®9

1 Press VIEW MODE.

o The View Mode menu displays.

The menu lists the View Mode options selectable for the type of video signal currently being received.

2 Press VIEW MODE or A/T while the View Mode menu is displayed to select a desired item on the menu.

You can sequentially select a View Mode that has its own aspect ratio.

Connect the PC before making adjustments.

(See page 14.) o Selectable screen size may vary with input signal type.

Example: Screen size images

Input signal

©1.

4:3

Normal

-©

Keeps the original aspect ratio in a full screen display.

Zoom

For viewing widescreen programs. The top and bottom of the image is cropped.

I

Input signal

©1.

16:9

Stretch

©

An image fully fills the screen.

Dot by Dot llol

Detects the resolution of the signal and displays an image with the same number of pixels on the screen.

Dot by Dot

Stretch

C)

An image fully fills the screen.

Detects the resolution of the signal and displays an image with the same number of pixels on the screen.

@39

Using a PC

2

Press MENU to display the MENU screen, and then press _/1_ to select the Setup or Option menu.

o For adjusting "Auto Sync." or "FineSync.", select the

Setup menu.

o For setting "PC Audio Select", select the Option menu.

Press A/V to select a specific adjustment item, and then press ENTER to set each item.

3

Press A/Y (or 4/1_) to select or adjust the desired setting, and then press ENTER.

Determines whether the AUDIO terminal is used for

INPUT 4 (PC-IN) or INPUT 6 (HDMI).

input 4 (PC}: Select this item when the audio signal is input via the INPUT 4 (PC-IN) terminal using an analog

RGB cable.

input 6 (HDMI}: Select this item when the audio signal is input via the INPUT 6 (HDMI) terminal using an HDMI-

DVI conversion cable.

o When "PC Audio Select" is set to "Input 6 (HDMI)", sound will not be produced if you use only an HDMI-certified cable to connect HDMI-compatible equipment. To produce sound, you should make an analog audio connection.

o If you want to connect HDMI-compatible equipment using only an HDMI-certified cable, set "PC Audio Select" to

"Input 4 (PC)".

For automatically adjusting the PC image.

Yes: Auto Sync. starts and "Now adjusting the image." displays.

No: This function does not work.

When "Auto Sync." is successful, "Completed" displays. If not, "Auto Sync." failed.

"Auto Sync." may fail even if "Completed" displays.

"Auto Sync." may fail if the computer image has low resolution, has unclear (black) edges, or is moved while executing "Auto Sync.".

o Be sure to connect the PC to the TV and switch it on before starting "Auto Sync.".

Ordinarily you can easily adjust the picture as necessary to change image position using "Auto Sync.".

In some cases, however, manual adjustment is needed to optimize the image.

H-Pos.: Centers the image by moving it to the left or right.

V-Pos,: Centers the image by moving it up or down.

Clock: Adjust when the image flickers with vertical stripes.

Phase: Adjust when characters have low contrast or when the image flickers.

o For resetting all "Fine Sync." adjustment items to the factory preset values, press A/Y to select "Reset", and then press

ENTER.

o It is not necessary to adjust the "Clock" or "Phase" when a digital signal is being input, so it cannot be selected.

o The default cursor position may not be in the center, because the screen position variable ranges may be asymmetrical.

o The screen position variable ranges depend on the View

Mode or the signal type. The ranges can be seen on the position-setting screen.

It is necessary to set the PC correctly to display XGA and WXGA signal.

VGA

SVGA

XGA

WXGA

SXGA

Resolution

SXGA+

UXGA

720 x 400

640 x 480

800 x 600

1024 x 768

1360 x 768

1280 x 1024

1400 x 1050

1600 x 1200

Horizontal Vertical VESA

Frequency Frequency Standard

31.5 kHz

31.5 kHz

37.9 kHz

37.5 kHz

35.1 kHz

37.9 kHz

48.1 kHz

46.9 kHz

48.4 kHz

56.5 kHz

60.0 kHz

47.7 kHz

64.0 kHz

65.3 kHz

75.0 kHz

70 Hz

60 Hz

72 Hz

75 Hz

56 Hz

60 Hz

72 Hz

75 Hz

60 Hz

70 Hz

75 Hz

60 Hz

60 Hz

60 Hz

60 Hz

O

O

O

O

O

O

O

O

O

O

O

O

O

O

VGA and XGA are registered trademarks of International i

Business Machines Corp.

l

Q40

Using a PC

[] PC control of the TV

• Attach an RS-232C cable cross-type (commercially available) to the supplied Din/D-Sub RS-232C for the connections.

[] Command format

Eight ASCII codes ÷ OR

Command 4-digits

I

Parameter 4-digits

_-_

Return code o This operation system should be used by a person who is accustomed to using computers.

[] Communication conditions

Set the RS-232C communication settings on the PC to match the TV's communication conditions.

The TV's communication settings are as follows:

Command 4-digits: Command.

The text of four characters.

Parameter 4-digits: Parameter 0-9, x, blank, ?

[] Parameter

Input the parameter values, aligning left, and fill with blank(s) for the remainder. (Be sure that 4 values are input for the parameter.)

When the input parameter is not within an adjustable range, "ERR" returns. (Refer to "Response code format".)

Any numerical value can replace the "x" on the table.

9,600 bps

8 bits

None

1 bit

None

[] Communication procedure

Send the control commands from the PC via the RS-

232C connector.

The TV operates according to the received command and sends a response message to the PC.

Do not send multiple commands at the same time.

Wait until the PC receives the OK response before sending the next command.

[] Command table

Commands not indicated here are not guaranteed to operate.

CONTROL ITEM COMMAND PARAMETER

POWER ON COMMAND SETRNG R)S)P)W i i i oi

11 i i i i Off

On

POWER SETIING

INPUTSELECTIONATOGGLE

TV

PiOiWi R 0i i i P......

off

i i i _i i

I ITIGID xl i i (Toggle)

I iTiViD oi i i

INPUTSELECTION

INPUT1 8

B INPUT 1

INPUT2

AV MODE SELECTION

I ;iA ;i V ;i D * i

I i N i P i 1 * i

I i N i P i 2 * i

AiV

) iMi D * i

) ) i

) ) i i i i i i i

)

Input terminal numbe/(1

0:Auto,

8)

1: VIDEO, 2: COMPONENT

O:Auto, 2: COMPONENT.

3: S TERMINAL

0:(Toggle),1: STANDARD, 2:MOVIE, 3:GAME, 4:USER,

5: DYNAMIC (Fixedl, 6 DYNAMIC, 7 PC, 100 AUTO

When "?" is input for some conamands, the present setting value responds.

[] Response code format

Normal response

Return code (0DH)

Problem response (communication error or incorrect command)

IEImIR

Return code (0DH)

CONTROL CONTENTS

The Power On command rejected.

The Power On command accepted.

It shifts to standby.

Power On

It input switches by the toggle.

(It is the same as an input change key)

It input switches to TV. (A channel/÷mains

It input switches to INPUT1 _INPUTS.

as it is. (L_st memory))

An input change is also included.

Although it can choose now, it is toggle operation in inside.

VOLUME

POSITION

VIEWMODE

H-POSITION

V POSITION

V ;iO ;i L ;iM * i * i

H i P i O i S * i * i * i i

V i P i o i S * i * i * i

Volume {0_60)

CLOCK CiL iciK * i * i * i Only PCmode.(0

PC

180)

_O

WiliDiE

) ) i i i

)

*i i i

) ) i i i

)

O:(T°ggle)[AV]'l:SideBar[AV]'2:SStretch[AVl

3: Zoom [AV}, 4: Stretch [AV], 5: Normal [PC]

6: Zoom [PC], 7: Stretch [PC],

8: Dot by Dot [PC] [AV], 9: EuUScreen [AV]

The screen position variable ranges depend on the View Mode or the signal type. The ranges can be seen on the position setting screen.

0: Although it carl choose now, it is toggle operation in inside.

1: Only available when 4:3 signal is being input.

5, 6: Only available when 4:3 signal is being input.

8: [PC] Avaibble except when UXGA is being input.

[AV] Only available when 1O8OVp is being input.

9: Only available when 720p is being input.

MUTE

SURROUND

AUDIO SELECTION

SLEEPTIMER

CHANNEL co

MiUiTiE *i i i 0: {Toggle), 1: On, 2: Off

AICISIUE E

A i O i H i A

*i x i i i i i 0: (Toggle), l: On, 2:Off

(Toggle) oiFiTiM i i i

*i i i i i i 0:Off, IOFFTIMER

3:OFFTIMER

30MIN,2:OFFTIMER

90MIN,4:OFFTIMER 120MIN

60MIN,

DIRECT D ) C ) C ) H * ) * ) * ) The channel number of %/

CHANNELi i i i i i (_13._)

(ANALOG) i i i i i i

DIRECT DiAl2 iP * i * i * i * (01009999)

CHANNEL

(DIGITAL)

Dici2i i i i

U *i*i*i iii

(1999)

OH UP

CH DOWN

1 1 i

1

*)*)*)(0999}

1 1 1

D i C i 1 i 1 * i * i * i * (O 6383)

O i H i U i P x i i i The channel number of%/+1 ciHiDiw xi i i The channel number of %/ oiYioiP xi i i (Toggle)

1

An input change is included if it is not %/display.

In Air, 2 690h is effective.

In Cable, 1 135ch is effective.

DIGITAL Air (Two Part numbers, 2 digit plus 2 digit)

DIGITAL Cable (Two Part numbers, 3 digit plus 3 digit)

E/_}nt half of DIGITAL CABLE CHANNEL NO. (Designate maior channel)

DIGITAL Cable (Two Part numbers, 3 digit plus 3 digit)

Rear half of DIGITAL CABLE CHANNEL NO. (Designate minor channel)

DIGITAL Cable (One Part numbers, 5 digit, less than 10,000)

DIGITAL Cable (One Part numbers, 5 digit, more than 10,000)

If it is not TV display, it will input switch to TV. (same function as CHA)

If it is not TV display, it will input switch to TV. (same function as CHV)

Toggle operation d a closed caption.

If an underbar (_)appears in the parameter column, enter a space.

= If an asterisk (*)appears, enter a value in the range indicated in brackets under CONTROL CONTENTS.

= Any numerical value can replace the "x" on the table.

Q41

Appendix

= Before detaching (or attaching) the stand, unplug the AC cord from the AC INPUT terminal.

Do not remove the stand from the TV unless using an optional wall mount bracket to mount it. r

Before attaching/detaching the stand

• Before performing work, make sure to turn off the TV.

1 2

Unfasten the four screws used to secure the stand in place.

Detach the stand from the TV.

To attach the stand, perform the above steps in reverse order.

This TV should be mounted on the wall only with the wall mount bracket AN-52AG4 (SHARP) (for LC-60E77UN) or AN-65AG1 (SHARP) (for LC-65E77UM).

The use of other wall mount brackets may result in an unstable installation and may cause serious injuries.

Installing the TV requires special skill that should only be performed by qualified service personnel.

Customers should not attempt to do the work themselves.

SHARP bears no responsibility for improper mounting or mounting that results in accident or injury.

Using an optional bracket to mount the "IV

You can ask a qualified service professional about using an optional AN-52AG4 or AN-65AG1 bracket to mount the

TV on the wall.

Carefully read the instructions that come with the bracket before beginning work.

Hanging on the wall

AN-52AG4 or AN-65AG1 wall mount bracket.

(See the bracket instructions for details.)

Vertical mounting Angular mounting

About setting the TV angle

0/5/10 °

AN-52AG4

LC-60E77UN

The center of the display:

1 6s/_ inches (50.0 mm) above the " f " position.

AN =65AG 1

LC=65E77UM

= The "A" position is at the center of the display.

,, Refer to the operation manual of AN-52AG4 or AN-65AG1 for details.

Q42

Detach the cable clamp on the rear of the TV when using the optional mount bracket.

To use this TV mounted on a wall, remove the covers at the 4 locations on the rear of the TV, and then use the screws supplied with the wall mount bracket to secure the bracket to the rear of the TV.

Some thicker AV cables may not fit within the 2 s/sqnch (60 mm) space limitation of AN-65AG1.

Appendix

o No power o Remote control unit does not operate.

No sound

Problem o Unit cannot be operated, o Picture is cut off/with sidebar screen, o Strange color, light color, or color misalignment o Power is suddenly turned off.

Possible Solution o Check if you pressed TV POWER on the remote control unit. ,_ Page 15

If the indicator on the TV does not light up, press POWER on the TV.

o Is the AC cord disconnected?

_ Page 7 o Has the power been turned on? ,,_Page 15 o External influences such as lightning, static electricity, may cause improper operation.

In this case, operate the unit after first turning off the power of the TV or unplugging the AC cord and replugging it in after 1 or 2 minutes.

o Is the FUNCTION set correctly? Set it to the TV setting position.

o Are batteries inserted with polarity (+, -) aligned? =_ Page 8 o Are batteries worn out? (Replace with new batteries.) o Are you using it under strong or fluorescent lighting?

o Is a fluorescent light illuminated near the remote control sensor?

o Is "RC Control Lock" selected in "Operation Lock Out"? ,_ Page 30 o Is the image position correct? ,_ Page 26 o Are screen mode adjustments such as picture size made correctly? =_Pages 19 and 39 o Adjust the picture tone. ,,_ Pages 22 and 23 o Is the room too bright? The picture may look dark in a room that is too bright.

o Is the sleep timer set? =_ Page 16 o Check the power control settings. ,,_ Page 24 o The unit's internal temperature has increased. Remove any objects blocking vent or clean.

o Is connection to other components correct? _ Pages 11, 12, 13, 14 and 35 o Is the volume too low? _, Page 16 o Is "Variable" selected in "Output Select"? _ Page 29

Have you pressed MUTE on the remote control unit? _, Page 16

Check the audio output of the connected external equipment.

Is the volume too low or muted?

When external equipment is connected via an HDMI cable, you may need to configure the audio to be output through the HDMI cable.

When audio is not output from external equipment connected to the INPUT 4 or

INPUT 6 terminal, check the "PC Audio Select" setting. • Page 40

Even when external equipment is connected using an HDMI-certified cable, an audio cable connection may be required depending on the type of equipment and the media being played back. In this case, in addition to connecting an HDMIcertified cable to the INPUT 6 (HDMI) terminal, connect an audio cable to the

AUDIO terminal and set "PC Audio Select" to "Input 6 (HDMI)". ,_ Page 40

When connecting a PC via an HDMI-certified cable, check the following:

- Is the audio output of the PC configured correctly? Check the audio output settings and output audio format in Sound Properties on the PC.

Only PCM format audio can be output. Compressed audio (with a sampling rate of 32kHz, 44.1 kHz, or 48kHz) and DTS format audio cannot be output.

- Depending on the board, only video signals may be output. In this case, in addition to connecting an HDMI-certified cable to the INPUT 6 (HDMI) terminal, connect an audio cable to the AUDIO terminal and set "PC Audio Select" to "Input

6 (HDMI)". _, Page 40

If you are using an HDMI-DVl conversion cable to connect external equipment to the TV, check the following:

- Is an audio cable connected?

The HDMI-DVI conversion cable is for video only.

Connect a D 3.5 mm stereo mini jack cable to listen to the audio.

- Is INPUT 6 being used? When the TV is connected to another HDMI terminal, the audio and video are not output together even if a © 3.5 mm stereo mini jack cable is connected to the shared AUDIO terminal for INPUT 4 and INPUT 6.

- Is "Input 4 (PC)" selected in "PC Audio Select"? _ Page 40

Q43

Appendix

o No picture

Problem o The TV sometimes makes a cracking sound.

Possible Solution o o o o o

Is connection to other components correct? _ Pages 11, 12, 13, 14 and 35

Is correct input signal source selected after connection? =_ Page 29

Is the correct input selected? _ Page 16

Is "On" selected in "Audio Only"? • Page 29

If the PC image is not displayed, check the following:

- When connecting a laptop PC to the TV, check that display output mode of the

PC is set to external monitor.

- Check the resolution setting on the PC. Is a non-compatible signal being input?

=_Page 40

This is not a malfunction. This happens when the cabinet slightly expands and contracts according to change in temperature. This does not affect the TV's performance.

The error message about reception of broadcast

Error code The example of an error message displayed on a screen o Failed to receive broadcast.

E202 o No broadcast now.

E203

Possible Solution o Check the antenna cable. Check that the antenna is correctly setup.

o Check the broadcast time in the program guide.

Cautions regarding use in high and low temperature environments

o When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed.

This is not a malfunction, and the unit will recover when the temperature returns to normal.

o Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near a heater, as this may cause the cabinet to deform and the Liquid Crystal panel to malfunction.

Storage temperature: - 4°F to ÷ 140°F (- 20°C to ÷ 60°C)

Q44

Appendix

LCD panel

TV

Function

Backlight

Audio out

Terminals

Weight

Size

Item

Resolution

Model: LC-60E77UN

60" Class (60 1/s2"Diagonal)

2,073,600 pixels (1,920 x 1,080)

TV-standard (OO1%

VHF/UHF

CATV

American TV Standard ATSC/NTSC System

VHF 2-13ch, UHF 14-69ch

1-135ch (non-scrambled channel only)

Receiving

Channel

2-69ch

Digitalcable*_

(64/256QAM) 1-135ch (non-scrambled channel only)

Audio multiplex BTSC System

Model: LC-65E77UM

65" Class (64 ss/j,

60,000 hours (at Backlight Standard position)

10W x 2

AV in, COMPONENT in

COMPONENT in, S-VIDEO in

Diagonal)

INPUT 1

INPUT 2

INPUT 4

INPUT 6

INPUT 7

Rear INPUT 8

ANT/CABLE

ANALOG RGB (PC) in (15-pin mini D-sub female connector), Audio in (® 3.5 mm jack)

HDMI in with HDCP, Audio in (® 3.5 mm jack)

HDMI in with HDCP

HDMI in with HDCP

75 _2Unbalance, F Type x 1 for Analog (VHF/UHF/CATV) and Digital (AIR/CABLE)

AUDIO Audio in (© 3.5 mm jack)

DBITALAUDI00UTPUTOptical Digital audio output x 1 (PCM/Dolby Digital)

OUTPUT Audio out

Side

OSD language

Power Requirement

Power Consumption

RS-2320

INPUT 3

INPUT 5

SERVICE

TV + stand

TV only

9-pin D-sub male connector

AV in

HDMI in with HDCP

Software update

English/French/Spanish

AC 120 V, 60 Hz

390 W (0.4 W Standby with AC 120 V)

92.6 Ibs./42.0 kg

81.6 Ibs./37.0 kg

525 W (0.4 W Standby with AC 120 V)

110.2 Ibs./50.0 kg

99.2 Ibs./45.0 kg

Dimension*2

(W x H x D)

TV + stand

TV only

Operating temperature

56 5/s x 37 29/64x 17 9/16inch

+ 32°F to + 104°F (0°C to + 40°C)

60 s/4 x 39 27/s2x 17 9/10inch

Emergency alert messages via Cable are unreceivable.

•2 The dimensional drawings are shown on the inside back cover.

As part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

The listed optional accessory is available for the Liquid

Crystal Television.

Please purchase it at your nearest shop.

Additional optional accessories may be available in the near future. When purchasing, please read the newest catalogue for compatibility and check the availability.

Wall mount bracket

AN-52AG4

(for LC-60E77UN)

AN-65AG1

(for LC-65E77UM)

Q45

Appendix

m Software composition

The software included in this product is comprised of various software components whose individual copyrights are held by SHARP or by third parties.

m Software deve(oped by SHARP and open source software

The copyrights for the software components and various relevant documents included with this product that were developed or written by SHARP are owned by SHARP and are protected by the Copyright Act, international treaties, and other relevant laws. This product also makes use of freely distributed software and software components whose copyrights are held by third parties. These include software components covered by a GNU

General Public License (hereafter GPL), a GNU Lesser General Public License (hereafter LGPL) or other license agreement.

m Obtaining source code

Some of the open source software licensors require the distributor to provide the source code with the executable software components.

GPL and LGPL include similar requirements. For information on obtaining the source code for the open source software and for obtaining the GPL, LGPL, and other license agreement information, visit the following website: http://www, sharp usa. co m/g pl

We are unable to answer any questions about the source code for the open source software. The source code for the software components whose copyrights are held by SHARP is not distributed.

m Acknowledgements

The following open source software components are included in this product:

• linux kernel/busybox/uClibc/zlib/libpng/libjpeg

CLEARING THE SECRET NUMBER

If you forget the secret number, clear the secret number using the following procedure.

1 Select an item from the list below to display the secret number input screen. (For operating the on-screen display menu, see page 20.)

"EZ Setup", "CH Setup", "Parental CTRL" or "Reset" on the Setup menu.

"Color System" on the Option menu.

"Software Update" on the Digital Setup menu.

2 Press and hold both CHi'k and VOL+ on the TV simultaneously until the message appears on the screen.

I I I I I

The secret number is I I I I I "

As a precautionary measure, make a note of your secret number above, cut it from this manual,and keep it in a safe place.

Q46

Calling for Service

For location of the nearest Sharp Authorized Service, or to obtain product literature, accessories, supplies, or customer assistance, please call 1-800-BE-SHARP.

LiMiTED WARRANTY

CONSUMER LiMiTED WARRANTY

SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand Liquid Crystal Display product (the

"Product"), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.

This warranty does not apply to any appearance items of the Product or if the serial number or model number affixed to the Product has been removed, defaced, changed, altered or tampered with. This warranty does not cover installation or signal reception problems.

This limited warranty will not apply if the Product has been or is being used in a commercial setting or application; this warranty is meant solely for the non-commercial, household use of the Product by consumers in their home or residence.

If you intend to or already use this Product for commercial purposes or in a commercial setting, there are warranties available to cover your use of this Product, the terms of which may vary. Please contact 1-888-GO-SHARP for further information.

In order to enforce your rights under this limited warranty, you should follow the steps set forth below. You must be able to provide proof of purchase to the servicer, which proof must include the date of purchase.

To the extent permitted by applicable state law, the warranties set forth are in lieu of, and exclusive of, all other warranties, express or implied.

Specifically ALL OTHER WARRANTIES OTHER THAN THOSE SET FORTH ABOVE ARE EXCLUDED, ALL EXPRESS AND

IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE, AND FITNESS FOR A PARTICULAR

PURPOSE ARE SPECIFICALLY EXCLUDED.

IF, UNDER APPLICABLE STATE LAW, IMPLIED WARRANTIES MAY NOT VALIDLY BE

DISCLAIMED OR EXCLUDED, THE DURATION OF SUCH IMPLIED WARRANTIES IS LIMITED TO THE PERIOD(S) FROM THE DATE OF

PURCHASE SET FORTH BELOW.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS.

YOU MAY ALSO HAVE OTHER RIGHTS

WHICH VARY FROM STATE TO STATE.

The warranties given herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser and only for the time periods set forth herein.

No other representations or promises made by anyone are permitted.

Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise.

Sharp does not warrant nor shall Sharp be liable, or in any way responsible, for Products which have been subject to abuse (including, but not limited to, improper voltage), accident, misuse, negligence, lack of reasonable care, alteration, modification, tampering, misuse, improper operation or maintenance or any damages or defects in the

Product which were caused by repairs or attempted repairs performed by anyone other than a Sharp authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage.

Some states do not allow limits on warranties or on remedies for breach in certain transactions; in such states, the limits herein may not apply.

THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DiSTRiCT OF COLUMBIA AND PUERTO RICO.

Model Specific Section

Your Product Model Number & Description:

Warranty Period for this Product:

Additional Exclusions from

Warranty Coverage (if any):

Where to Obtain Service:

What to do to Obtain Service:

LC-60E77UN/LC-65E77UM LCD Color Television

(Be sure to have this information available when you need service for your

Product.)

One (1) year parts and labor from the date of purchase.

In order for the Product to be serviced, the Product must be readily available to the servicer, free and clear of any complex or non-standard installation, mounting or other encumbrance which would unreasonably interfere with servicing the Product.

The Servicer will remount the Product after service, provided that such remounting is not into a complex or non-standard installation. Any additional labor and materials required to remove and/or reinstall a

Product above and beyond the foregoing are not covered by this warranty, may result in additional charges and are the responsibility of the consumer.

Image Retention resulting from a fixed image being displayed for long periods of time is not covered by this Limited Warranty (see Operation

Manual on how to prevent this).

From a Sharp Authorized Servicer located in the United States. To find the location of the nearest Sharp Authorized Servicer, please call Sharp toll free at 1-800-BE-SHARR

Contact your Sharp Authorized Servicer to obtain in home service for this product. The Servicer will come to your location and if necessary remove the unit for repair at the Servicer's facility and return the set to you once completed.

Be sure to have Proof of Purchase available.

TO OBTAIN PRODUCT INFORMATION OR PURCHASE ACCESSORIES AND EXTENDED WARRANTIES, CALL 1=800=BE=SHARP

OR VISIT www.sharpusa.com

@47

LiMiTED WARRANTY

Consumer Electronics Products

Congratulations on your purchase!

Sharp Electronics of Canada Ltd. (hereinafter called "Sharp") gives the following express warranty to the first consumer purchaser for this

Sharp brand product, when shipped in its original container and sold or distributed in Canada by Sharp or by an Authorized Sharp Dealer:

Sharp warrants that this product is free, under normal use and maintenance, from any defects in materiam and workmanship.

If any such defects should be found in this 3roduct within the applicable warranty period, Sharp shall, at its option, repair or replace the product as specified herein.

This warranty shall not apNy to:

(a) Any defects caused or repairs required as a result of abusive operation, negmigence, accident, improper installation or inappropriate use as outlined in the owner's manual.

(b) Any Sharp product tampered with, modified, adjusted or repaired by any party other than Sharp, Sharp's Authorized Service Centres or Sharp's Authorized Servicing Dealers.

(c) Damage caused or repairs required as a result of the use with items not specified or approved by Sharp, including but not limited to head cmeaning tapes and chemical cmeaning agents.

(d) Any replacement of accessories, glassware, consumable or peripheral items required through normal use of the product including but not limited to earphones, remote controms, AC adapters, batteries, temperature probe, stylus, trays, fimters, belts, ribbons, cables and paper.

(e) Any cosmetic damage to the surface or exterior that has been defaced or caused by normal wear and tear.

(f) Any damage caused by external or environmental conditions, including but not limited to transmission mine/power line voltage or liquid spillage.

(g) Any product received without appropriate model, serial number and CSA/cUL markings.

(h) Any products used for rental or commercial purposes.

(i) Any installation, setup and!or programming charges.

Should this Sharp product fail to operate during the warranty period, warranty service may be obtained upon delivery of the Sharp product together with proof of purchase and a copy of this LIMITED WARRANTY statement to an Authorized Sharp Service Centre or an

Authorized Sharp Servicing Dealer.

In home warranty service may be provided at Sharp's discretion on any Sharp television with the screen size of 27" or margerand on any Sharp Over-the-Range Microwave Oven.

This warranty constitutes the entire express warranty granted by Sharp and no other dealer, service centre or their agent or employee is authorized to extend, enlarge or transfer this warranty on behalf of Sharp. To the extent the law permits, Sharp disclaims any and all liabimity for direct or indirect damages or losses or for any incidental, special or consequential damages or moss of profits resulting from a defect in material or workmanship relating to the product, incmuding damages for the moss of time or use of this Sharp product or the loss of information.

The purchaser will be responsible for any removal reinstallation, transportation and insurance costs incurred.

Correction of defects, in the manner and period of time described herein, constitute complete fulfimlment of aH oNigations and responsibilities of Sharp to the purchaser with respect to the product and shah constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise.

WARRANTY PERIODS:

Audio Product

Camcorder

DVD Product

Projector

LCD TV

Microwave Oven

Air Purifier

Portabme Air Conditioner

Parts & Labour (exceptions noted)

1 year

1 year

1 year

1 year (lamp 90 days)

1 year

1 year (magnetron component-4 additionN years)

1 year

1 year

To obtain the name and address of the nearest Authorized Sharp Service (?entre or Dealer, please contact:

SHARP ELECTRONICS OF CANADA LTD, 335 Britannia Road East, Mississauga, Ontario L4Z IW9

For more information on this Warranty, Sharp Extended Warranty

Offers, Sharp Canada Products, Accessory Sales, Dealer or Service

Locations, please call (905) 568=7140

Visit our Web site: www.sharp.ca

._

_,

SHARP

-_'

Revision 12/16/05

Q48

Dimensional Drawings

LC-60E77UN

56 5/8 (1438)

52 17/32 (1334)

I

v o_LO

C_J_

Unit: inch (mm)

Unite: pouce (mm)

Unidad: pulgada (mm)

J

L

24 21/32 (626) _1

I

5 5/15

(135) t

4 45/64

(119)

AN =52AG4

LC-65E77UM

r

[

I

60 3/4 (1543) r

03

-_ 17 9/16 (448) _, u3

!--

J

5 5/15

(135)

I I

L 2421j_2/626/.1

AN=65AG1

4 45/64

(119)

17 9/16 (446) ,_

SHARP

SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07495-1163

SHARP CORPORATION

Printed in Mexico

Imprime au Mexique

Impreso en Mexico

TINS-E339WJZZ

09P09-MX-NM

Sharp LC-60E77UN LCD Television Owner's Manual

SHARR

AQUOS

LIQUID CRYSTAL TELEVISION

Ti_=Li'_VISEURACL

TELEVISOR CON PANTALLA

DE CRISTAL LiQUIDO

OPERATI(

MODE

MANI

NYCE

If]DOLBY

DIGITAL ]

LiQUiD CRYSTAL TELEViSiON

ENGLISH

OPERATION MANUAL

iMPORTANT INFORMATION

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE

SLOT, FULLY INSERT.

(LC-60E77UN only)

iMPORTANT iNFORMATiON

INFORMATION:

This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury.

Disposal of these materials may be regulated due to environmental considerations.

For disposal or recycling information, please contact your local authorities, the Electronic Industries Alliance: www.eiae.org, the lamp recycling organization: www.lamprecycle.org

or Sharp at 1-800-BE-SHARP

(For U.S.A. only)

Trademarks

DEAR SHARP CUSTOMER

iMPORTANT SAFETY iNSTRUCTiONS

1)

9) lo)

11)

12)

13)

14)

iMPORTANT SAFETY iNSTRUCTiONS

ANTENNA

7" IGRO ND,NG

7ONDUCTORS

iMPORTANT SAFETY iNSTRUCTiONS

Contents

Supplied Accessories

r

QUICK REFERENCE

Preparation

Cable

L :.Q

Part Names

r

_t oPc,nd,eator 22.//

v

(CH/VV)

®®

@-9

1 17

_I_Tv, ovoV°R°

18

12

13

14

15

16

T ....

, i i iiiiiiiii "i

.....T

•

20

21

22

23

24

25

26

27

28

29

3O