Instructions - Parts List

RAZOR

®

Gravity

Feed Gun

A premier gun for the automotive refinish market.

Important Safety Instructions

Read all warnings and instructions in this manual.

Save these instructions.

Includes LVLP, HVLP, Compliant, and Conventional Series.

See page 2 for List of Models and maximum working pressures.

See page 10 for Parts.

This manual is available in the following languages.

English

Spanish

French

German

Italian

312101

312102

312103

312104

312105

312101H

TI8206

II 2 G

Models

Contents

Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 14

Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . 14

2

Models

Part

Number Series Spray Type

288561

288562

A

A

LVLP

LVLP

288563

288564

288565

288566

A

A

A

A

LVLP

LVLP

LVLP

HVLP

288567

288568

288569

288570

288571

289840

288572

288573

288574

288575

A

A

A

A

A

A

A

A

A

A

HVLP

HVLP

HVLP

HVLP

HVLP

HVLP

HVLP

HVLP

HVLP

Compliant

288576

288577

288578

288657

288579

288580

288581

A

A

A

A

A

A

A

Compliant

Compliant

Compliant

Compliant

Compliant

Compliant

Compliant

Max HVLP/

Comp Pressure psi (MPa, bar)

16 (0.1, 1.1)

16 (0.1, 1.1)

Nozzle

(mm) Application

Air

Cap Nozzle

Needle

Assy

Needle

Tip

Air Cap with

Retaining

Ring

1.2

Clear, Base 253823 253802 253771 288752 289500

1.3

Clear, Base 253823 253803 253771 288752 289500

16 (0.1, 1.1)

16 (0.1, 1.1)

16 (0.1, 1.1)

29 (0.2, 2.0)

1.4

1.5

1.6

1.0

Clear, Base 253823 253804 253772 253917

Clear, Base 253823 253805 253772 253917

Clear, Base 253823 253806 253772 253917

Clear, Base 253824 253792 253769 288751

289500

289500

289500

289501

29 (0.2, 2.0)

29 (0.2, 2.0)

29 (0.2, 2.0)

29 (0.2, 2.0)

29 (0.2, 2.0)

29 (0.2, 2.0)

29 (0.2, 2.0)

29 (0.2, 2.0)

29 (0.2, 2.0)

35 (0.24, 2.4)

1.2

Clear, Base 253824 253793 253771 288752 289501

1.3

Clear, Base 253824 253794 253771 288752 289501

1.4

Clear, Base 253824 253795 253772 253917 289501

1.5

Clear, Base 253824 253796 253772 253917 289501

1.7

Clear, Base 253824 253797 253772 253917 289501

1.3

1.5

1.8

Primer

Primer

Primer

253828 289841 253771 288752

253828 253789 253772 253917

253828 253790 253772 253917

289505

289505

289505

35 (0.24, 2.4)

35 (0.24, 2.4)

35 (0.24, 2.4)

35 (0.24, 2.4)

35 (0.24, 2.4)

35 (0.24, 2.4)

35 (0.24, 2.4)

2.3

Primer 253829 253791 253774 234779 289506

1.0

Clear, Base,

Primer

253825 253816 253769 288751 289502

1.2

Clear, Base,

Primer

253825 253817 253771 288752 289502

1.3

Clear, Base,

Primer

253825 253818 253771 288752 289502

1.4

Clear, Base,

Primer

253825 253819 253771 288752 289502

1.5

Clear, Base,

Primer

253825 288653 253772 253917 289502

1.6

Clear, Base,

Primer

253825 253820 253772 253917 289502

2.0

Clear, Base,

Primer

253826 253821 253774 234779 289503

2.5

Clear, Base,

Primer

253826 253822 253775 234780 289503

312101H

Warnings

289218

289219

289220

289393

289394

289573

289395

289396

289574

Part

Number Series Spray Type

288582

288583

A

A

Conventional

Conventional

Max HVLP/

Comp Pressure psi (MPa, bar)

Nozzle

(mm) Application

N/A

N/A

1.2

1.3

Air

Cap Nozzle

Needle

Assy

Needle

Tip

Clear, Base 288451 288295 253772 253917

Clear, Base 288451 288296 253772 253917

Air Cap with

Retaining

Ring

289507

289507

288584

288585

288586

288587

A

A

A

A

Conventional

Conventional

Conventional

Conventional

N/A

N/A

N/A

N/A

1.4

Clear, Base 288451 288297 253771 288752 289507

1.6

Clear, Base 288451 288298 253772 253917 289507

1.8

2.5

Primer

Primer

288452 288299 253772 253917

288453 288300 253775 234780

289508

289509

A

A

A

A

A

A

A

A

A

HVLP

HVLP

HVLP

HVLP

HVLP

HVLP

Compliant

Compliant

Compliant

29 (0.2, 2.0)

29 (0.2, 2.0)

29 (0.2, 2.0)

26 (0.18, 1.8)

26 (0.18, 1.8)

26 (0.18, 1.8)

35 (0.24, 2.4)

35 (0.24, 2.4)

35 (0.24, 2.4)

1.3

1.4

1.5

1.2

1.3

1.4

1.2

1.3

1.4

Metallic

Metallic

Metallic

289212 253794 253771 288752

289212 253795 253772 253917

289212 253796 253772 253917

Waterborne 289374 289380 253771 288752

Waterborne 289375 289381 253771 288752

Waterborne 289375 289561 253771 288752

Waterborne 289376 289382 253771 288752

Waterborne 289377 289383 253771 288752

Waterborne 289377 289562 253771 288752

289514

289514

289514

289599

289600

289600

289601

289602

289602

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment.

The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. Refer back to these warnings. Additional, productspecific warnings may be found throughout the body of this manual where applicable.

WARNING

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode.

To help prevent fire and explosion:

• Use equipment only in well ventilated area.

• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths (potential static arc).

• Keep work area free of debris, including solvent, rags and gasoline.

• Do not plug or unplug power cords or turn lights on or off when flammable fumes are present.

• Ground all equipment in the work area. See Grounding instructions.

• If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until you identify and correct the problem.

• Keep a working fire extinguisher in the work area.

312101H 3

Warnings

WARNING

PRESSURIZED EQUIPMENT HAZARD

Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and cause serious injury.

• Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning, checking, or servicing equipment.

• Tighten all fluid connections before operating the equipment.

• Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals.

• Use fluids and solvents that are compatible with equipment wetted parts. See

Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings.

• Check equipment daily. Repair or replace worn or damaged parts immediately.

• Do not alter or modify equipment.

• Use equipment only for its intended purpose. Call your Graco distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or overbend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

PERSONAL PROTECTIVE EQUIPMENT

You must wear appropriate protective equipment when operating, servicing, or when in the operating area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic fumes, burns, and hearing loss. This equipment includes but is not limited to:

• Protective eyewear

• Clothing and respirator as recommended by the fluid and solvent manufacturer

• Gloves

• Hearing protection

4 312101H

Setup

Setup

• Check that your shop air provides adequate air flow.

• Use a minimum 3/8 in. (10 mm) ID air hose.

• Set shop air pressure regulator (not supplied) according to paint manufacturer’s recommendation. See maximum pressures and compliant

air pressures on page 2.

• Make sure no air restrictions, such as low-volume cheater-valves, obstruct the air flow. If an air adjusting valve is desired, use a Graco adjustable air valve (288744 or 234387) or Digi-tell

(288652).

• Install a shutoff valve (not supplied) downstream of the air regulator to shut off gun air.

• Install an inline air filter (not supplied) to clean and dry the gun air supply.

Spraying

CAUTION

Excessive atomizing air pressure can increase over-spray, reduce transfer efficiency, and result in a poor quality finish.

Regulatory agencies in certain states prohibit the operation of a spray gun above 10 psi (69 kPa, 0.7 bar) atomizing air cap pressure.

1. Fill the cup with material. Do not fill past the full markings on cup.

2. Turn on the shop air to the gun and set atomizing pressure with the gun fully triggered.

3. Adjust the pattern size and shape with the fluid adjust knob (8). Fluid adjust knob (8) is factory set for maximum needle trigger travel and material flow. Turn knob clockwise to reduce pattern size/ fluid flow and counterclockwise to increase it.

See Troubleshooting, page 8, if you

experience an irregular pattern.

1. Shut off the air supply.

2. Connect a clean, dry, filtered air supply to

the air inlet fitting (25). See page 10.

3. If this is the first time using the equipment,

flush the gun. See page 6.

Operation

Volatile Organic Compounds

(VOC) Regulation

In certain states, spraying solvents that release

VOCs into the atmosphere when cleaning a spray gun is prohibited. To comply with these air quality laws, you must use a cleaning method that prevents the escape of VOC vapors into the atmosphere. See Compliant

Cleaning Methods, page 6.

Clean air line filters as directed by the manufacturer.

Pressure Relief Procedure

1. Turn off the gun air supply.

2. Trigger the gun to relieve pressure.

312101H 5

6

Maintenance

Maintenance

2. Use a rag moistened in solvent to wipe outside of gun and cup.

3. Make sure cup lid vent hole is clear.

4. Blow dry gun inside and out. Lubricate, see

Maintenance, page 6.

• Frequently lubricate the gun moving parts with a drop of non-silicone oil.

• Do not disassemble the spray gun if you are having a spray pattern problem. See

Troubleshooting, page 8, for information

on how to correct the problem.

• Check for fluid leakage. Tighten fittings or replace equipment as needed.

Flush

Flush before using the equipment, before changing colors, and when you are done spraying. Use solvent that is compatible with gun wetted parts and fluid that will be sprayed.

See Compliant Cleaning Methods, page 6,

to comply with air quality laws if applicable.

1. Relieve pressure, page 5.

2. Dispose of any paint in the cup.

3. Fill the cup with a small amount of solvent.

4. Spray into a grounded metal waste container until the equipment is clean.

5. Relieve pressure, page 5.

Cleaning Gun and Cup

CAUTION

• Do not submerge gun in solvent. Solvent dissolves lubricant, dries out packings, and clogs air passages.

• Do not use metal tools to clean air cap holes as this may scratch them and distort the spray pattern.

• Use a compatible solvent.

1. Flush, page 6.

See Compliant Cleaning Methods, page 6,

to comply with air quality laws if applicable.

Cleaning Nozzle and Air Cap

1. Remove air cap (13), trigger gun, remove nozzle (11), and soak both in a compatible cleaning solution.

2. Clean them and the front of the gun with a soft-bristle brush dipped into compatible solvent. Do not use a wire brush or metal tools.

3. Use a soft implement, such as a toothpick to clean out air cap holes.

When reassembling, make sure the air cap matches the color etched onto the side of the nozzle (gold, brown, grey, blue, etc.).

Compliant Cleaning Methods

1. Place spray gun in a gun washer that completely encloses the gun and components during cleaning, rinsing, and draining.

2. Spray solvent through the spray gun into a closed gun cleaning station.

312101H

Repair

See Parts, page 10, for callout references.

Needle Replacement

1. Remove knob (8), spring (29), and needle

(9). Inspect. Replace tip (9a) or needle (9)

as necessary. See page 2.

2. Insert needle (9), spring (29), and knob (8).

Nozzle Replacement

1. Unscrew retaining ring (14) to remove air cap assembly (13).

2. Trigger gun while unscrewing nozzle (11) to prevent needle damage.

3. Check o-ring (21) and replace if necessary.

4. Trigger gun while replacing nozzle (11).

5. Insert air cap assembly (13) into gun.

6. Screw retaining ring (14) into place.

Air Control Valve Replacement

1. Remove air control valve assembly (5).

2. Insert replacement assembly (5) into gun.

Fluid Inlet Fitting Replacement

PRESSURIZED EQUIPMENT HAZARD

• Fluid inlet gasket (3) must be replaced if fluid inlet fitting (4) is removed from spray gun.

• Failure to replace gasket (3) may result in air leakage into the fluid section causing a non-vented gravity cup to become pressurized.

1. Remove fluid inlet fitting (4).

2. Remove fluid inlet gasket (3) from gun body and discard.

312101H

Repair

3. Apply thread sealant to replacement fluid inlet fitting (4) threads.

4. Snap the fluid inlet gasket (3) securely onto the fluid inlet fitting (4).

5. Screw in fluid inlet fitting (4) and torque to

155-165 in.-lb (17.5-18.6 N•m).

6. Replace washer (28) as required.

Air Valve Replacement

1. Remove trigger nut (24), trigger pin (23), wave washer (18), and trigger (10).

2. Remove knob (8), spring (29), needle (9) and nut (7).

3. Remove spring (31) and push the air valve assembly (6) out the back of the gun.

4. Inspect u-cup seals (22) and replace if necessary.

5. Lubricate gun as described in Mainte-

nance, page 6.

6. Insert replacement air valve assembly (6).

Replace spring (31) and nut (7).

7. Replace trigger (10), wave washer (18), trigger pin (23), trigger nut (24), needle (9), spring (29), and knob (8).

Needle Packing Replacement

1. Remove trigger nut (24), trigger pin (23), wave washer (18), and trigger (10).

2. Remove knob (8), spring (29), and needle (9).

3. Unscrew nut (17) and remove u-cup (16) and spreader (15).

4. Insert replacement spreader (15) facing

back of gun, u-cup (16) facing front of gun, and nut (17).

5. Replace trigger (10), wave washer (18), trigger pin (23), trigger nut (24), needle (9), spring (29), and knob (8).

7

Troubleshooting

Troubleshooting

Problem Cause

Normal pattern.

Solution

No action necessary.

8

Right

Wrong

Heavy top or bottom pattern

Wrong

Split pattern

Dirty or damaged air cap or fluid nozzle.

Pressure too high for viscosity of material being sprayed.

Rotate air cap 180°.

If pattern follows air cap, problem is in air cap (13). Clean and inspect. If pattern is not corrected, replace air cap.

If pattern does not follow the air cap, the problem is with the fluid nozzle. Clean and inspect the nozzle. If the pattern is not corrected, replace nozzle.

Reduce air pressure and increase material viscosity.

Correct pattern by narrowing fan size with spray width adjustment knob (8).

Dirty or distorted air horn holes.

Clean and inspect air cap. If pattern is not corrected, replace air cap.

Wrong

Gun spitting Air getting into paint stream.

Check if cup is empty and fill.

Tighten fluid nozzle (11).

Check and tighten needle packing nut (17).

Check fluid nozzle (11) for damage.

Replace fluid inlet gasket (3).

Damaged fluid nozzle seal (21).

Replace seal (21).

Will not spray Cup is empty.

Fill cup.

Excessive air blowing back

Fluid adjustment knob (8) turned too far clockwise.

Loose fluid nozzle (11).

Adjust knob (8) counterclockwise.

Tighten fluid nozzle (11).

Damaged fluid nozzle seal (21).

Replace seal (21).

312101H

Technical Data

Technical Data

Maximum Air Inlet Pressure . . . . . . . . . . . . . . . . . . . . . . 100 psi (0.7 MPa, 7 bar)

Maximum HVLP/Compliant Inbound Air Pressure:

LVLP gravity feed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 psi (0.1 MPa, 1.1 bar)*

HVLP gravity feed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 psi (0.2 MPa, 2.0 bar)*

Compliant gravity feed. . . . . . . . . . . . . . . . . . . . . . . . . . . 35 psi (0.24 MPa, 2.4 bar)*

Air Consumption:

LVLP Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.8 CFM at 16 psi (0.1 MPa, 1.1 bar)

HVLP Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.4 CFM at 29 psi (0.2 MPa, 2.0 bar)

Compliant Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.2 CFM at 35 psi (0.24 MPa, 2.4 bar)

Conventional Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3 CFM at 43 psi (0.3 MPa, 3.0 bar)

Fluid and Air Operating Temperature Range. . . . . . . . . 32°F to 109°F (0°C to 43°C)

Spray Gun:

Air Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4 npsm (R1/4-19)

Weight with cup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3 lbs (0.6 kg)

Sound Data:

LVLP sound pressure at 16 psi (0.1 MPa, 1.1 bar) . . . . . 80.8 dB(A)**

LVLP sound power at 16 psi (0.1 MPa, 1.1 bar) . . . . . . . 87.6 dB(A)**

HVLP sound pressure at 29 psi (0.2 MPa, 2.0 bar) . . . . 83.9 dB(A)**

HVLP sound power at 29 psi (0.2 MPa, 2.0 bar). . . . . . . 90.8 dB(A)**

Compliant sound pressure at 35 psi (0.24 MPa, 2.4 bar) 81.8 dB(A)**

Compliant sound power at 35 psi (0.24 MPa, 2.4 bar) . . 88.7 dB(A)**

Conventional sound pressure at 43 psi (0.3 MPa, 3.0 bar) 79.52 dB(A)**

Conventional sound power at 43 psi (0.3 MPa, 3.0 bar) . 88.05 dB(A)**

Gravity Cup Size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 oz. (0.68 liter) cup

Wetted Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303 SST, 17-4 PH SST, PEEK, acetal,

UHMWPE

* Produces 10 psi (0.07 MPa, 0.7 bar) spraying pressure at air cap.

** All readings were taken with the fan valve fully open (fan full size) at the assumed operator position. Sound power was tested per ISO 9614-2.

312101H 9

Parts

Parts

8‡

3

‡29

9

4

9a

3

*‡22

3

‡31

*‡6

3 *‡22

17

3 2

*†16

3 2

*†15

4 3 7

**24

1

8

^25

7‡

8

5

6 10 28* ✿

4

5 9

3*

23**

3

18**

21*

11

1 9

19* ◆✓

13 ✓

20* ◆✓

30

10

6

10** 14 ✓

TI8205

1

2

3

4

5

6

7

8

9

10

Pull trigger before installing nozzle (11).

Insert spreader (15) with tapered end facing rear of gun. Insert u-cup (16) with open end facing front of gun.

Apply lubricant.

Apply low strength thread retainer.

Apply thread sealant.

Torque to 85-90 in-lbs (9.6-10.2 N•m).

Torque to 15-20 in-lbs (1.7-2.2 N•m).

Torque to 175-185 in-lbs (19.8-20.9 N•m).

Torque to 155-165 in-lbs (17.5-18.6 N•m).

Install with valve assembly turned fully CCW to outermost position.

10 312101H

Accessories

Ref.

No.

Part No. Description Qty.

16*†

17

18**

19*

◆✓

20* ◆✓

21*

22*‡

23**

24**

25^

1

3*

4

BODY, gun

GASKET, fluid inlet

253971 FITTING, fluid inlet,

5

6*‡

7‡

8‡ includes gasket (item 3)

253976 VALVE, air control, assy

VALVE, air, assy

NUT

KNOB, fluid adjust

1

1

9

9a

10** TRIGGER 1

11 page 2 NOZZLE (includes 21) 1

13

✓ page 2 AIR CAP 1

14 ✓ 253970 RING, retaining 1

15*† SPREADER, needle 1

1

1 page 2 NEEDLE (includes 9a) 1 page 2 TIP, needle 1

1

1

1 packing

U-CUP, needle packing 1

253972 NUT, needle packing

WASHER, wave

1

1

O-RING, PTFE

WASHER, UHMWPE

O-RING, PTFE

PACKING, u-cup

1

2

1

1

PIN, trigger

NUT, trigger

FITTING, air inlet

1

1

1

Ref.

No.

Part No. Description

28*

✿

29‡

WASHER, UHMWPE

SPRING, fluid

30 253979 VALVE, air inlet

30a^ adjustment

PLUG, air inlet (not

31‡

32

36*‡

Qty.

1

1

1

1 shown, sold separately)

SPRING, air valve 1

253974 TOOL, gun (not shown) 1

TOOL, seal installation 1

37

(not shown)

288661 CUP, gravity, 650cc 1

(not shown)

37a 289195 FILTER, cup (not shown) 1

* Included in Gun Repair Kit 253783

(purchase separately).

** Included in Trigger Repair Kit 253785

(purchase separately).

† Included in Needle Packing Repair Kit

253748 (purchase separately).

‡ Included in Air Valve Repair Kit 253934

(purchase separately).

◆ Included in Air Cap Seal Kit 253784

(purchase separately).

^ Included in Air Inlet Fitting Repair Kit

253933 (purchase separately).

Accessories

Repair Kits

Part No. Description

253748 Needle Packing Repair Kit

253783 Gun Repair Kit

253784 Air Cap Seal Kit

253785 Trigger Repair Kit

253933 Air Inlet Fitting Repair Kit

253934 Air Valve Repair Kit

289213 Cup gasket 10 Pack Kit

Air Valves

Part No.

Description

288744 High Volume Air Adjusting Valve with

Gauge

234387 High Output Precision Air Valve

288652 Digi-tell Digital Air Adjusting Valve

312101H

PPS Adapters

Part No. Description

253975 PPS Adapter

Test Gauges

Part No. Description

253447 LVLP Verification

253746 HVLP Primer 1.5/1.8 Verification

287985 HVLP Verification

287986 HVLP Primer 2.3 Verification

289962 HVLP Waterborne 1.2 Verification

289963 HVLP Waterborne 1.3/1.4 Verification

11

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by

Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED

TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy

(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT

MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information

TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.

Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

This manual contains English. MM 312101

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441

Copyright 2007, Graco Inc. is registered to I.S. EN ISO 9001 www.graco.com

Revised March 2008