- Home
- Do-It-Yourself tools
- Power tools
- Paint Sprayer
- Graco
- 332561D, LineLazer IV 250SPS 3rd or 4th Gun Kit 24P930
- Owner's manual
Graco 332561C - LineLazer IV 250SPS 3rd or 4th Gun Kit 24P930 Owner's Manual
Add to my manuals6 Pages
advertisement
Installation
LineLazer lV 250
SPS
3rd or 4th Gun Kit 24P930
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions and warnings in this manual and in 3A2090 or 3A2593. Save all instructions.
3300 psi (22.7 MPa, 227.5 bar) Maximum Working Pressure
332561C
EN ti21710a
2
Pressure Relief Procedure
Pressure Relief Procedure
Follow the Pressure Relief Procedure whenever you see this symbol.
5. Engage gun trigger safety.
This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splashing fluid and moving parts, follow the Pressure
Relief Procedure when you stop spraying and before cleaning, checking, or servicing the equipment.
1. Perform Grounding Procedure if using flammable materials.
2. Set pump valve OFF . Turn engine OFF .
ti3324a
6. Turn prime valve down.
ti6740a ti6473a
3. Turn pressure control to lowest setting. ti3441a
4. Trigger gun to relieve pressure.
ti3305a
332561C
Installation
Installation
1. Perform Pressure Relief Procedure
2. Install extension clamp support bracket (9).
ti21721a
7. Install exposed cable through cable bracket slot.
ti21734a
3. Pull out existing gun arm support bracket. ti21719a ti18997a
8. Insert plastic cable retainer into cable bracket hole.
4. Slide extension clamp onto existing gun arm support bracket.
ti18999a
9. Install cable end onto trigger plate pin and install clip. ti21720a
5. Install existing gun support bracket. ti21716a
6. Install extension support bracket (9) and tighten the clamp.
ti18998a
10. Route cable around unit and up through cable holes behind hose mount. Use tie straps (16) to secure cable to unit.
ti21712a
332561C 3
Installation
11. Route cable end loop through rectangular hole in bracket and insert plastic cable retainer into the slotted hole on the actuator bracket. Install cable end onto actuator rod and install clip.
14. Align guns.
ti21711a ti21713a
NOTE: Each gun actuator is capable of operating two cables. For either gun installation, attach cable to the actuator rod.
12. Remove plug from filter.
15. Position guns (up/down, forward/reverse, left/right).
ti21733a
13. Connect paint hose to filter. Connect adapter fittings
(5, 7, 18) to filter. Connect hose (10) to adapter nipple (18).
ti21718a
16. Fourth Gun Placement: Mount spacer (22) to support bracket(9). Mount support bracket (9) to small existing gun arm support.
ti21717a ti21714a ti21715a ti23532a
17. Pointer Mount (opposite side) included to allow flexibility in position the pointer.
4 332561C
Parts
Parts
6
4
24
23
28
22
18
5
18
10
7
21
20
25
1
19
8
26
27
3
2
16
9
12, 13
11
Ref. Part
8
9
10
11
12
13
6
7
4
5
1
2
3
Description
16M671 CABLE, gun, solenoid
24M638 BAR, gun holder, LL IV 250 SPS
126111 RETAINER, clip, external, 8mm
287566 KIT, clamp
124490 FITTING, tee, street
188135 GUIDE, cable
196179 FITTING, elbow, street
235457 GUN, flex, basic
16T552 HOLDER, 3rd gun (same side)
245798 HOSE, cpld, 1/4 in. x 7 ft
243161 GUARD, RAC 5
LL5319 TIP, spray, RAC 5, striping
286421 TIP, spray, RAC 5
Qty
.
1
1
1
1
1
1
1
1
1
1
1
1
1
Ref. Part
23
24
25
26
27
28
14
16
18
19
20
21
22
Description
222385 TAG, warning
STRAP, tie
196177 ADAPTER, nipple
24U759 HOLDER, 3rd gun (opposite side)
24N170 BRACKET, mount, pointer
111145 KNOB, pronged
16Y970 SPACER, gun support
159346 WASHER
102040 NUT, lock, hex
114653 SCREW, cap, flange head
100527 WASHER, plain
111040 NUT, lock, insert, nylock, 5/16
118887 HOSE, air
Qty
.
2
6
1
1
2
1
2
1
1
1
1
1
2
332561C 5
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
For patent information, see www.graco.com/patents.
Original instructions.
This manual contains English. MM 332561
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2013, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revision C - April 2014
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project