advertisement
Z97M-PLUS
ii
E9678
Second Edition
August 2014
Copyright
©
2014 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.
Offer to Provide Source Code of Certain Software
This product contains copyrighted software that is licensed under the General Public License (“GPL”), under the Lesser General Public License Version (“LGPL”) and/or other Free Open Source Software
Licenses. Such software in this product is distributed without any warranty to the extent permitted by the applicable law. Copies of these licenses are included in this product.
Where the applicable license entitles you to the source code of such software and/or other additional data, you may obtain it for a period of three years after our last shipment of the product, either
(1) for free by downloading it from http://support.asus.com/download or
(2) for the cost of reproduction and shipment, which is dependent on the preferred carrier and the location where you want to have it shipped to, by sending a request to:
ASUSTeK Computer Inc.
Legal Compliance Dept.
15 Li Te Rd.,
Beitou, Taipei 112
Taiwan
In your request please provide the name, model number and version, as stated in the About Box of the product for which you wish to obtain the corresponding source code and your contact details so that we can coordinate the terms and cost of shipment with you.
The source code will be distributed WITHOUT ANY WARRANTY and licensed under the same license as the corresponding binary/object code.
This offer is valid to anyone in receipt of this information.
ASUSTeK is eager to duly provide complete source code as required under various Free Open Source
Software licenses. If however you encounter any problems in obtaining the full corresponding source code we would be much obliged if you give us a notification to the email address [email protected], stating the product and describing the problem (please DO NOT send large attachments such as source code archives, etc. to this email address).
Contents
Chapter 1:
Product Introduction
Product highlights........................................................................1-1
5X Protection...............................................................................1-2
ASUS Exclusive Features ...........................................................1-2
Other special features .................................................................1-3
1.2.1 Before you proceed .....................................................................1-3
Motherboard layout .....................................................................1-4
Central Processing Unit (CPU) ...................................................1-6
System memory ..........................................................................1-7
1.2.5 Expansion slots ...........................................................................1-9
1.2.7 Onboard buttons and switches..................................................1-12
Onboard LEDs ..........................................................................1-14
Internal connectors....................................................................1-15
Chapter 2: Basic installation
Motherboard installation ..............................................................2-1
CPU installation...........................................................................2-3
CPU heatsink and fan assembly installation ...............................2-4
DIMM installation.........................................................................2-6
ATX Power connection................................................................2-7
SATA device connection .............................................................2-8
Front I/O Connector ....................................................................2-9
2.1.8 Expansion Card installation.......................................................2-10
Motherboard rear and audio connections .............................................2-11 2.2
Rear I/O connection ..................................................................2-11
Audio I/O connections ...............................................................2-13
iii
iv
Chapter 3: BIOS setup
EZ Mode......................................................................................3-3
Advanced Mode ..........................................................................3-4
QFan Control...............................................................................3-7
3.2.4 EZ Tuning Wizard .......................................................................3-9
3.6.1 CPU Configuration ....................................................................3-30
PCH Configuration ....................................................................3-33
PCH Storage Configuration.......................................................3-34
System Agent Configuration .....................................................3-36
USB Configuration ....................................................................3-37
Platform Misc Configuration ......................................................3-38
Onboard Devices Configuration ................................................3-40
APM Configuration ....................................................................3-42
Network Stack Configuration.....................................................3-43
3.9.1 ASUS EZ Flash 2 Utility ............................................................3-53
ASUS Overclocking Profile .......................................................3-54
ASUS SPD Information .............................................................3-55
3.11.2 ASUS EZ Flash 2 ......................................................................3-58
3.11.3 ASUS CrashFree BIOS 3 ..........................................................3-59
3.11.4 ASUS BIOS Updater .................................................................3-60
Chapter 4:
Software support
Installing an operating system .................................................................4-1
Running the support DVD ...........................................................4-1
Obtaining the software manuals..................................................4-2
4.4.3 TurboV EVO ................................................................................4-8
USB 3.0 Boost...........................................................................4-11
EZ Update .................................................................................4-12
Push Notice ...............................................................................4-13
4.4.8 System Information ...................................................................4-16
Chapter 5:
RAID support
5.1.1 RAID definitions ..........................................................................5-1
5.1.2 Installing Serial ATA hard disks ..................................................5-2
5.1.3 Setting the RAID item in BIOS ....................................................5-2
Rapid Storage Technology Option ROM utility ..................5-3
Creating a RAID driver disk without entering the OS ..................5-7
Creating a RAID driver disk in Windows
....................................5-8
Installing the RAID driver during Windows
Appendices
v
vi
Safety information
Electrical safety
• To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system.
• When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
• Before connecting or removing signal cables from the motherboard, ensure that all power cables are unplugged.
• Seek professional assistance before using an adapter or extension cord. These devices could interrupt the grounding circuit.
• Ensure that your power supply is set to the correct voltage in your area. If you are not sure about the voltage of the electrical outlet you are using, contact your local power company.
• If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.
Operation safety
• Before installing the motherboard and adding devices on it, carefully read all the manuals that came with the package.
• Before using the product, ensure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately.
• To avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry.
• Avoid dust, humidity, and temperature extremes. Do not place the product in any area where it may become wet.
• Place the product on a stable surface.
• If you encounter technical problems with the product, contact a qualified service technician or your retailer.
About this guide
This user guide contains the information you need when installing and configuring the motherboard.
How this guide is organized
This guide contains the following parts:
• Chapter 1: Product introduction
This chapter describes the features of the motherboard and the new technology it supports. It includes description of the switches, jumpers, and connectors on the motherboard.
• Chapter 2: Basic installation
This chapter lists the hardware setup procedures that you have to perform when installing system components.
• Chapter 3: BIOS setup
This chapter tells how to change system settings through the BIOS Setup menus.
Detailed descriptions of the BIOS parameters are also provided.
• Chapter 4: Software support
This chapter describes the contents of the support DVD that comes with the motherboard package and the software.
• Chapter 5: RAID support
This chapter describes the RAID configurations.
Where to find more information
Refer to the following sources for additional information and for product and software updates.
1. ASUS websites
The ASUS website provides updated information on ASUS hardware and software products. Refer to the ASUS contact information.
2. Optional documentation
Your product package may include optional documentation, such as warranty flyers, that may have been added by your dealer. These documents are not part of the standard package.
vii
viii
Conventions used in this guide
To ensure that you perform certain tasks properly, take note of the following symbols used throughout this manual.
DANGER/WARNING:
Information to prevent injury to yourself when trying to complete a task.
CAUTION:
Information to prevent damage to the components when trying to complete a task
IMPORTANT:
Instructions that you MUST follow to complete a task.
NOTE:
Tips and additional information to help you complete a task.
Typography
Bold text
Italics
<Key>
Indicates a menu or an item to select.
Used to emphasize a word or a phrase.
Keys enclosed in the less-than and greater-than sign means that you must press the enclosed key.
Example: <Enter> means that you must press the Enter or
Return key.
<Key1> + <Key2> + <Key3> If you must press two or more keys simultaneously, the key names are linked with a plus sign (+).
Z97M-PLUS specifications summary
CPU
Chipset
Memory
Expansion slots
Graphics
Multi-GPU support
Storage
LAN
LGA1150 socket for the 4th, New 4th & 5th Generation Intel
®
Core™ i7/
Core™ i5 / Core™ i3, Pentium
®
, and Celeron
®
processors
Supports 22nm CPU
Supports Intel ® Turbo Boost Technology 2.0*
* The Intel ® Turbo Boost Technology 2.0 support depends on the CPU types.
** Refer to www.asus.com for Intel ® CPU support list.
Intel ® Z97 Express Chipset
4 x DIMM, max. 32GB, DDR3 3200(O.C.)*/3100(O.C.)*/3000(O.C.)*/
2933(O.C.)*/2800(O.C.)*/2666(O.C.)*/2600(O.C.)*/2400(O.C.)*/
2250(O.C.)*/2200(O.C.)*/2133(O.C.)*/2000(O.C.)*/ 1866(O.C.)*/
1600/1333MHz, non-ECC, un-buffered memory
Dual-channel memory architecture
Supports Intel
®
Extreme Memory Profile (XMP)
* Hyper DIMM support is subject to the physical characteristics of individual
CPUs. Please refer to Memory QVL (Qualified Vendors List) for details.
** Refer to www.asus.com for the Memory QVL (Qualified Vendors List).
1 x PCI Express 3.0/2.0 x16 slot (at x16 mode)
1 x PCI Express 2.0 x16 slot (max. at x4 mode, compatible with PCIe x1 and x4 devices)
2 x PCI slots
Integrated Graphics Processor - Intel ® HD Graphics support
Multi-VGA output support: HDMI/DVI-D/RGB port
Supports HDMI with max. resolution of 4096 x 2160 @24Hz / 2560 x
1600 @60Hz
Supports DVI-D with max. resolution of 1920 x 1200 @60Hz
Supports RGB with max. resolution of 1920 x 1200 @60Hz
Supports Intel
®
InTru™ 3D, Intel
®
Quick Sync Video, Intel
®
Clear Video
HD Technology, and Intel
®
Insider™
Supports up to three displays simultaneously
Maximum shared memory of 512MB
Supports AMD
®
Quad-GPU CrossFireX™ Technology
Intel ® Z97 Express Chipset with RAID 0, 1, 5, 10 and Intel
Rapid Storage Technology 13 support
®
- 1 x M.2 Socket 3*
- 6 x SATA 6.0 Gb/s ports (gray)
- Supports Intel ® Smart Response Technology, Intel
Technology, and Intel ®
® Rapid Start
Smart Connect Technology**
* This socket supports M Key and type 2242/2260/2280 storage devices (Type
2242 storage device is supported on Rev. 2.00 or later versions of this motherboard).
** These functions will work depending on the CPU installed.
Gigabit Intel LAN controllers- 802.3az Energy Efficient Ethernet (EEE) appliance
Intel
®
I218-V Gigabit LAN- Dual interconnect between the integrated
LAN controller and physical layer (PHY)
(continued on the next page) ix
x
Z97M-PLUS specifications summary
Audio
USB
ASUS special features
Realtek ® ALC887 7.1-channel high definition audio CODEC featuring
Crystal Sound 2
Audio Shielding: Ensures precision analog/digital separation and greatly reduced multi-lateral interference
Dedicated audio PCB layers: Separate layers for left and right channels to guard the quality of the sensitive audio signals
Audio amplifier: Provides the highest-quality sound for headphone and speakers
Premium Japanese-made audio capacitors: Provide warm, natural and immersive sound with exceptional clarity and fidelity
Unique de-pop circuit: Reduces start-up popping noise to audio outputs
Supports jack-detection, multi-streaming, and front panel jack-retasking
Intel ®
Boost
Z97 Express Chipset - supports ASUS USB 3.0
- 6 x USB 3.0/2.0 ports (2 ports at mid-board, 4 ports at rear panel
[blue])
- 8 x USB 2.0/1.1 ports (6 ports at mid-board, 2 ports at rear panel)
High Performance
ASUS 5X PROTECTION
- ASUS motherboards safeguard your PC with 5X PROTECTION:
DIGI+ VRM, DRAM Fuse, ESD Guards, High-Quality 5K-Hour
Solid Capacitors, and Stainless Steel Back I/O ensure the best quality, reliability, and durability
ASUS Digital Power Design
- ASUS Digital Power Control: Digital Power Design for the CPU
- ASUS 4 Phase Power Design
- ASUS CPU power utility
ASUS DRAM Fuse
- Enhanced DRAM overcurrent protection and short circuit damage prevention
ASUS ESD Guards
- Enhanced ESD protection
ASUS High-Quality 5K Solid Capacitors
- 2.5x Longer lifespan with excellent durability
ASUS Stainless Steel Back I/O
- 3x More durable corrosion-resistant coating
UEFI BIOS
- Most advanced options with fast response time
M.2 onboard
- The latest transfer technologies with up to 10 Gb/s data transfer speeds
ASUS Fan Xpert3
- Featuring Fan Auto Tuning function and multiple thermistors selection for optimized system cooling control.
ASUS EPU
- EPU
Interactive HomeCloud
Media Streamer
- Pipe music or movies from your PC to a smart TV
- Media Streamer app for portable smartphone/tablet, supporting iOS 7 and Android 4.0 system
(continued on the next page)
Z97M-PLUS specifications summary
ASUS special features
ASUS quiet thermal solution
ASUS exclusive overclocking features
Gaming Scenario
Crystal Sound 2
- Flawless audio that makes you part of the game
Steam support
- Compatible with the most fun gaming platform under Windows
®
system
ASUS Exclusive Features
- USB 3.0 Boost
- Ai Charger
- AI Suite 3
- Disk Unlocker
- MemOK!
EZ DIY
Push Notice
- Monitor your PC status with smart devices in real time
UEFI BIOS EZ Mode
- featuring friendly graphics user interface
- ASUS O.C. Tuner
- ASUS CrashFree BIOS 3
- ASUS EZ Flash 2
Q-Design
- ASUS Q-DIMM
- ASUS Q-Slot
Quiet Thermal Design
- ASUS Fan Xpert 3
- Stylish Fanless Design: PCH Heat-sink & MOS Heat-sink solution
Precision Tweaker 2
- vCore: Adjustable CPU Core voltage at 0.001V increment
- iGPU: Adjustable CPU Graphics voltage at 0.001V increment
- vCCIO: Adjustable Analog and Digital I/O voltage at 0.001V increment
- vCCIN: Adjustable CPU Input voltage at 0.01V increment
- vCCSA: Adjustable CPU System Agent voltage at 0.001V increment
- vDRAM Bus: 124-step Memory voltage control
- vPCH: 154-step Chipset voltage control
SFS (Stepless Frequency Selection)
- BCLK/PCIE frequency tuning from 80MHz up to 300MHz at 0.1MHz increment
Overclocking Protection
- ASUS C.P.R.(CPU Parameter Recall)
(continued on the next page) xi
xii
Z97M-PLUS specifications summary
Back Panel I/O Ports
Internal I/O connectors / jumpers / buttons
BIOS features
Manageability
Support DVD contents
Operating system support
Form factor
1 x PS/2 mouse / keyboard combo port
1 x HDMI port
1 x DVI-D port
1 x RGB port
1 x LAN (RJ-45) port
4 x USB 3.0/2.0 ports (blue)
2 x USB 2.0/1.1 ports
6 x audio jacks support 7.1-channel
1 x 19-pin USB 3.0/2.0 connector supports additional 2 USB ports
3 x USB 2.0/1.1 connectors support additional 6 USB ports
1 x M.2 Socket 3 (for M Key, type 2242/2260/2280 devices)*
6 x SATA 6.0 Gb/s connectors (gray)
1 x 4-pin CPU Fan connector for both 3-pin (DC mode) and 4-pin (PWM mode) CPU coolers control**
2 x 4-pin Chassis Fan connectors for both 3-pin (DC mode) and 4-pin (PWM mode) coolers control
1 x Front panel audio connector (AAFP)
1 x S/PDIF out header
1 x 24-pin EATX Power connector
1 x 8-pin EATX 12V Power connector
1 x System panel connector
1 x MemOK! button
1 x GPU Boost switch (advanced two-stage adjustments)
1 x Parallel port connector
1 x Clear CMOS jumper
1 x TPM header
1 x COM port
* This socket supports M Key and type 2242/2260/2280 storage devices (Type 2242 storage device is supported on Rev. 2.00 or later versions of this motherboard).
** The CPU Q-Fan control setting is set as default in Auto mode for detecting the type of CPU fan installed and switches to the control mode automatically.
64 Mb Flash ROM, UEFI AMI BIOS, PnP, DMI 2.7, WfM 2.0, SM BIOS 2.8,
ACPI 5.0, Multi-language BIOS, ASUS EZ Flash 2, CrashFree BIOS 3, F11
EZ Tuning Wizard, F6 Qfan Control, F3 My Favorites, Quick Note, Last
Modified Log, F12 PrintScreen function, F3 Shortcut function, and ASUS
DRAM SPD (Serial Presence Detect) memory information
WfM 2.0, DMI 2.7, WOL by PME, PXE
Drivers
ASUS Utilities
EZ Update
Anti-virus software (OEM version) unique features
Windows
®
8.1
Windows
®
8
Windows ® 7 uATX form factor: 9.6 in. x 8.8 in. (24.4 cm x 22.4 cm)
Specifications are subject to change without notice.
Package contents
Check your motherboard package for the following items
User Guide
ASUS Z97M-PLUS motherboard User guide Support DVD
2 x Serial ATA 6.0 Gb/s cables 1 x ASUS I/O-Shield
• If any of the above items is damaged or missing, contact your retailer.
• The illustrations above are for reference only. Actual product specifications may vary with different models.
xiii
xiv
Installation tools and components
1 bag of screws
PC chassis
Intel
®
LGA1150 CPU
DIMM
Philips (cross) screwdriver
Power supply unit
Intel
®
LGA1150 compatible CPU Fan
SATA hard disk drive
SATA optical disc drive (optional) Graphics card (optional)
The tools and components in the table above are not included in the motherboard package.
Chapter 1: Product Introduction
Product introduction
1.1 Special features
1
1.1.1 Product highlights
Intel
®
LGA1150 4th, New 4th & 5th Generation Core™ i7 / Core™ i5 / Core™ i3, Pentium
®
, and Celeron
®
Processors Ready
This motherboard supports the 4th, New 4th & 5th Generation Intel ® Core™ i7 / Core™ i5
/ Core™ i3, Pentium
®
, and Celeron
®
processors in the LGA1150 package. It provides great graphics and system performance with its GPU, dual-channel DDR3 memory slots and PCI
Express 2.0/3.0 expansion slots.
Intel
®
Z97 Express Chipset
Intel ® Z97 Express Chipset is a single chipset that supports the LGA1150 socket for the 4th,
New 4th & 5th Generation Intel
®
Core™ i7/ Core™ i5/ Core™ i3, Pentium
®
, and Celeron
® processors. It utilizes the serial point-to-point links, which increases bandwidth and enhances the system’s performance. It natively supports up to six USB 3.0 ports, six SATA 6 Gb/s ports, and M.2 support for faster data retrieval. It also enables the iGPU function for Intel
® integrated graphics performance.
PCI Express
®
3.0
PCI Express
®
3.0 (PCIe 3.0) is the PCI Express bus standard that provides twice the performance and speed of PCIe 2.0. It provides an optimal graphics performance, unprecedented data speed, and seamless transition with its complete backward compatibility to PCIe 1.0/2.0 devices.
Intel
®
Desktop Responsiveness Technologies
Intel Desktop Responsiveness Technologies comprise of three technologies: Intel Rapid
Start Technology, Intel Smart Response Technology, and Intel Smart Response Technology.
These technologies provide faster and better performance for your computer, allow your system to receive the freshest updates from the Internet, and quickly resume your system from a deep sleep or hibernate mode.
Dual-Channel DDR3 3200 (O.C) / 1600 / 1333 MHz Support
The motherboard supports the dual-channel DDR3 memory that features data transfer rates of DDR3 3200 (O.C.)* / 1600 / 1333 MHz to boost the system’s performance, and to meet the higher bandwidth requirements of 3D graphics, multimedia and Internet applications.
Quad-GPU CrossFireX™ Support
This motherboard features the most powerful Intel
®
Z97 platform that optimizes PCIe allocation in multi-GPU CrossFireX™ solution, giving you a brand-new gaming enjoyment.
ASUS Z97M-PLUS
1-1
1-2
M.2 Support
This motherboard features the M.2 slot, which shares bandwidth with PCI Express x2 slot to speed up data transfer up to 10 Gb/s. This helps enhance the performance of your SSD
(Solid State Drive) that is dedicated only to the operating system. The M.2 slot also includes
Intel Rapid Storage Technology support for faster access to data and applications, and quicker wake up time for your system.
Complete USB 3.0 integration
This motherboard offers you the strategic USB 3.0 accessibility for both the front and rear panels, allowing you to experience the convenience of the latest plug and play connectivity solution at speed up to ten times faster than USB 2.0.
Native SATA 6 Gb/s support
With Intel ® Z97 Express Chipset natively support for the next-generation Serial ATA (SATA) storage interface, this motherboard delivers up to 6.0 Gb/s data transfer rates. It also provides enhanced scalability, faster data retrieval, double the bandwidth of current bus systems.
Gigabit LAN support
Z97M-PLUS features Gigabit LAN design which complies with 802.3az Energy Efficient
Ethernet (EEE) standard and allows a PC to serve as a network gateway for managing traffic between two separate networks. Intel ® Gigabit LAN controller on this motherboard which reduces power consumption during normal operation and enhances faster transfer speed through dual interconnection between the Integrated LAN controller and Physical Layer
(PHY).
1.1.2 5X Protection
5X PROTECTION
ASUS motherboards guard your PC with 5X PROTECTION. We use quality components like
ESD units tested to strict standards that eliminate electrostatic interference, polyswitches
(resettable fuses) around DRAM slots to prevent overcurrent and short-circuit damage, and a corrosion-resistant back I/O shield. All examples of ASUS providing the best possible reliability and durability.
1.1.3 ASUS Exclusive Features
Crystal Sound 2
Crystal Sound 2 makes short work of optimizing audio settings for the way you want to listen, be it gaming, chatting, watching movies or relaxing to your favorite music. Onboard physical shielding, professional engineered design and premium components, including Japanesemade audio capacitors and operational amplifiers (op-amps), result in sound output that has exceptional clarity and fidelity. Discover a whole new dimension of superior audio and get ready to rule!
Chapter 1: Product introduction
ASUS HomeCloud
ASUS HomeCloud creates a world without boundaries. It lets you access your PC remotely, stream multimedia content to wherever you want, and manage all your stuff from anywhere- no matter where it’s stored. Use the built-in Wake on WAN feature to remotely wake and control your PC with a single smart device, anywhere and anytime. It even turns your hard drive into a private cloud, removing worries about storage limits. With HomeCloud, your PC becomes the gateway to your world.
1.1.4 Other special features
ErP Ready
The motherboard is European Union’s Energy-related Products (ErP) ready, and ErP requires products to meet certain energy efficiency requirement in regards to energy consumptions. This is in line with ASUS vision of creating environment-friendly and energyefficient products through product design and innovation to reduce carbon footprint of the product and thus mitigate environmental impacts.
1.2 Motherboard overview
1.2.1 Before you proceed
Take note of the following precautions before you install motherboard components or change any motherboard settings.
• Unplug the power cord from the wall socket before touching any component.
• Before handling components, use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, to avoid damaging them due to static electricity.
• Hold components by the edges to avoid touching the ICs on them.
• Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that came with the component.
• Before you install or remove any component, ensure that the ATX power supply is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, or components.
ASUS Z97M-PLUS
1-3
1-4
1.2.2 Motherboard layout
KBMS_USB78
1 2
EATX12V
3 4 5 1
GPU Boost
GPU_LED
DIGI
+VRM
CPU_FAN
22.4cm(8.8in)
CHA_FAN2
6
BATTERY
MemOK!
DRAM_LED
7
8
9
HDMI
ASM
1442K
USB3_56
LAN_USB3_34
LGA1150
2
AUDIO
Intel
I218-V
CHA_FAN1
Z97M-PLUS
PCIEX16_1
Super
I/O
ALC
887
AAFP
20
LPT
19
PCI1
Intel
Z97
®
ASM
1083
PCI2
SB_PWR
PCIEX16_2
SPDIF_OUT
TPM
COM USB910 USB1112
CLRTC
USB1314
18 17 16 15
PANEL
14
10
11
12
13
Refer to 1.2.9 Internal connectors and 2.2.1 Rear I/O connection for more information about rear panel connectors and internal connectors.
Chapter 1: Product introduction
Layout contents
Connectors/Jumpers/Slots
1. CPU and chassis fan connectors (4-pin CPU_FAN, 4-pin CHA_FAN1/2)
2. ATX power connectors (24-pin EATXPWR, 8-pin EATX12V)
3. GPU Boost LED (GPU_LED)
4. GPU Boost switch
5. LGA1150 CPU socket
6. DDR3 DIMM slots
7. USB 3.0 connector (20-1 pin USB3_12)
8. DRAM LED (DRAM_LED)
9. MemOK! button
10. Intel
®
Z97 Serial ATA 6.0 Gb/s connectors (7-pin SATA6G_1-6)
11. M.2 Socket 3
12. Standby power LED (SB_PWR)
13. Clear RTC RAM (3-pin CLRTC)
14. System panel connector (20-8 pin PANEL)
15. USB 2.0 connectors (10-1 pin USB910, USB1112, USB1314)
16. Serial port connector (10-1 pin COM)
17. TPM header (20-1 pin TPM)
18. Digital audio connector (4-1 pin SPDIF_OUT)
19. LPT connector (26-1 pin LPT)
20. Front panel audio connector (10-1 pin AAFP)
1-14
1-12
1-15
1-22
1-14
1-11
1-21
1-17
1-16
1-19
1-17
1-20
1-19
Page
1-18
1-20
1-14
1-13
1-6
1-7
1-16
ASUS Z97M-PLUS
1-5
1.2.3 Central Processing Unit (CPU)
The motherboard comes with a surface mount LGA1150 socket designed for the 4th, New
4th & 5th Generation Intel
®
Core™ i7 / Core™ i5 / Core™ i3, Pentium™, and Celeron™ processors.
Z97M-PLUS
Z97M-PLUS CPU socket LGA1150
• Ensure that all power cables are unplugged before installing the CPU.
• Ensure that you install the correct CPU designed for LGA1150 only. DO NOT install a
CPU designed for LGA1155 and LGA1156 sockets on the LGA1150 socket.
• Upon purchase of the motherboard, ensure that the PnP cap is on the socket and the socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket contacts/motherboard components. ASUS will shoulder the cost of repair only if the damage is shipment/ transit-related.
• Keep the cap after installing the motherboard. ASUS will process Return Merchandise
Authorization (RMA) requests only if the motherboard comes with the cap on the
LGA1150 socket.
• The product warranty does not cover damage to the socket contacts resulting from incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the PnP cap.
1-6 Chapter 1: Product introduction
1.2.4 System memory
The motherboard comes with four Double Data Rate 3 (DDR3) Dual Inline Memory Modules
(DIMM) slots.
A DDR3 module is notched differently from a DDR or DDR2 module. DO NOT install a DDR or DDR2 memory module to the DDR3 slot.
DIMM_A1 DIMM_A2 DIMM_B1 DIMM_B2
Z97M-PLUS
Z97M-PLUS 240-pin DDR3 DIMM sockets
Recommended memory configurations
ASUS Z97M-PLUS
1-7
1-8
Memory configurations
You may install 2GB, 4GB, and 8GB unbuffered and non-ECC DDR3 DIMMs into the DIMM sockets.
• You may install varying memory sizes in Channel A and Channel B. The system maps the total size of the lower-sized channel for the dual-channel configuration. Any excess memory from the higher-sized channel is then mapped for single-channel operation.
• According to Intel CPU spec, DIMM voltage below 1.65V is recommended to protect the CPU.
• Always install DIMMs with the same CAS latency. For optimum compatibility, we recommend that you obtain memory modules from the same vendor.
• Due to the memory address limitation on 32-bit Windows
®
OS, when you install 4GB or more memory on the motherboard, the actual usable memory for the OS can be about 3GB or less. For effective use of memory, we recommend that you do any of the following: a) Use a maximum of 3GB system memory if you are using a 32-bit Windows
®
OS.
b) Install a 64-bit Windows
®
OS when you want to install 4GB or more on the motherboard.
c) For more details, refer to the Microsoft com/kb/929605/en-us.
® support site at http://support.microsoft.
• This motherboard does not support DIMMs made up of 512Mb (64MB) chips or less
(Memory chip capacity counts in Megabit, 8 Megabit/Mb = 1 Megabyte/MB).
• The default memory operation frequency is dependent on its Serial Presence Detect
(SPD), which is the standard way of accessing information from a memory module.
Under the default state, some memory modules for overclocking may operate at a lower frequency than the vendor-marked value. To operate at the vendor-marked or at a higher frequency, refer to section 3.5 Ai Tweaker menu for manual memory frequency adjustment.
• For system stability, use a more efficient memory cooling system to support a full memory load (4 DIMMs) or overclocking condition.
• Memory modules with memory frequency higher than 2133MHz and their corresponding timing or the loaded XMP profile is not the JEDEC memory standard.
The stability and compatibility of the memory modules depend on the CPU’s capabilities and other installed devices.
• Always install the DIMMS with the same CAS Latency. For an optimum compatibility, we recommend that you install memory modules of the same version or data code (D/
C) from the same vendor. Check with the vendor to get the correct memory modules.
• ASUS exclusively provides hyper DIMM support function.
• Hyper DIMM support is subject to the physical characteristics of individual CPUs. Load the X.M.P. or D.O.C.P. settings in the BIOS for the hyper DIMM support.
• Visit the ASUS website for the latest QVL.
Chapter 1: Product introduction
1.2.5 Expansion slots
Unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components.
Z97M-PLUS
PCIEX16_1
PCI1
PCI2
PCIEX16_2
Slot No. Slot Description
1
2
PCIe 3.0/2.0 x16_1 slot (at x16 mode)
PCI slot 1
3
4
PCI slot 2
PCIe 2.0 x16_2 slot (max. at x4 mode, compatible with PCIe x1 and x4 devices)
ASUS Z97M-PLUS
1-9
1-10
VGA configuration
Single VGA/PCIe card
Dual VGA/PCIe card
PCIe Express operating mode
PCIe 3.0/2.0 x16_1 PCIe 2.0 x16_2
x16 (single VGA recommended) x16
N/A x4
• In single VGA card mode, use the PCIe 3.0/2.0 x16_1 slot (gray) for a PCI Express x16 graphics card to get better performance.
• We recommend that you provide sufficient power when running CrossFireX™ mode.
• Connect a chassis fan to the motherboard connector labeled CHA_FAN1/2 when using multiple graphics cards for better thermal environment.
IRQ assignments for this motherboard
PCIe x16_1
PCIe x16_2
PCI1
PCI2
Intel SATA Controller
Intel LAN
Intel xHCI
Intel EHCI 1
Intel EHCI 2
HD Audio
A B
shared – shared –
– – shared –
–
–
–
–
–
–
–
– shared
–
– –
C
–
D
–
E
–
F
–
G
–
H
–
–
–
– – – – – –
–
–
– shared –
– – –
– shared –
–
– shared
–
–
–
–
–
–
–
–
–
–
– shared –
– – –
– shared
–
–
–
–
–
–
–
–
–
–
– shared
–
–
Chapter 1: Product introduction
1.2.6 Jumpers
Clear RTC RAM (3-pin CLRTC)
This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the
CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords.
To erase the RTC RAM:
Z97M-PLUS
1 2
CLRTC
2 3
Clear RTC Normal
(Default)
Z97M-PLUS Clear RTC RAM
1. Turn OFF the computer and unplug the power cord.
2. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3 for about 5~10 seconds, then move the cap back to pins 1-2.
3. Plug the power cord and turn ON the computer.
4. Hold down the <Del> key during the boot process and enter BIOS setup to reenter data.
Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default position. Removing the cap will cause system boot failure!
• If the steps above do not help, remove the onboard battery and move the jumper again to clear the CMOS RTC RAM data. After clearing the CMOS, reinstall the battery.
• You do not need to clear the RTC when the system hangs due to overclocking. For system failure due to overclocking, use the CPU Parameter Recall (C.P.R) feature.
Shut down and reboot the system so the BIOS can automatically reset parameter settings to default values.
ASUS Z97M-PLUS
1-11
1-12
1.2.7 Onboard buttons and switches
Onboard switches and buttons allow you to fine-tune performance when working on a bare or open-case system. This is ideal for overclockers and gamers who continually change settings to enhance system performance.
1. MemOK! button
Installing DIMMs that are not compatible with the motherboard may cause system boot failure, and the DRAM_LED near the MemOK! switch lights continuously. Press and hold the MemOK! button until the DRAM_LED starts blinking to begin automatic memory compatibility tuning for successful boot.
Z97M-PLUS
Z97M-PLUS MemOK! button
• Refer to section 1.2.8 Onboard LEDs for the exact location of the DRAM_LED.
• The DRAM_LED also lights up when the DIMM is not properly installed. Turn off the system and reinstall the DIMM before using the MemOK! function.
• The MemOK! switch does not function under Windows ® OS environment.
• During the tuning process, the system loads and tests failsafe memory settings. It takes about 30 seconds for the system to test one set of failsafe settings. If the test fails, the system reboots and test the next set of failsafe settings. The blinking speed of the DRAM_LED increases, indicating different test processes.
• Due to memory tuning requirement, the system automatically reboots when each timing set is tested. If the installed DIMMs still fail to boot after the whole tuning process, the DRAM_LED lights continuously. Replace the DIMMs with ones recommended in the Memory QVL (Qualified Vendors Lists) on the ASUS website at www.asus.com.
• If you turn off the computer and replace DIMMs during the tuning process, the system continues memory tuning after turning on the computer. To stop memory tuning, turn off the computer and unplug the power cord for about 5–10 seconds.
• If your system fails to boot up due to BIOS overclocking, press the MemOK! switch to boot and load the BIOS default settings. A message will appear during POST reminding you that the BIOS has been restored to its default settings.
• We recommend that you download and update to the latest BIOS version from the
ASUS website at www.asus.com after using the MemOK! function.
Chapter 1: Product introduction
2. GPU Boost switch
With its two-level adjustment functions, the GPU Boost switch allows you to automatically adjusts the CPU Ratio and clock speed for an optimal system performance.
GPU Boost
GPU_I GPU_II
Z97M-PLUS
Disable
(Default)
Enabled
(GPU Boost and
CPU Ratio Boost)
Enabled
(GPU Boost and
CPU BCLK/Ratio
Boost)
Z97M-PLUS GPU Boost switch
• To ensure system performance, enable this switch when the system is powered off.
• When the GPU switch is set to Enabled (GPU_I: GPU Boost and CPU Ratio
Boost), the system automatically adjusts the GPU and CPU ratio for an enhanced performance.
• When the GPU switch is set to Enabled (GPU_II: GPU Boost and CPU BCLK/Ratio
Boost), the system automatically adjusts the GPU, base clock rate (BCLK) and the
CPU ratio for a more enhanced performance.
• The GPU Boost LED near the GPU Boost switch lights up when the GPU Boost switch is enabled. Refer to section 1.2.8 Onboard LEDs for the exact location of the GPU
Boost LED.
• If you enable this switch under the Windows
®
OS environment, the GPU Boost function will be activated after the next system bootup.
• You may use the TurboV feature in the AI Suite 3 application, adjust the BIOS setup program or enable the GPU Boost switch at the same time. However, the system will use the last setting you have made.
ASUS Z97M-PLUS
1-13
1.2.8 Onboard LEDs
1. Standby Power LED
The motherboard comes with a standby power LED that lights up to indicate that the system is ON, in sleep mode, or in soft-off mode. This is a reminder that you should shut down the system and unplug the power cable before removing or plugging in any motherboard component. The illustration below shows the location of the onboard LED.
1-14
Z97M-PLUS
SB_PWR
Z97M-PLUS Onboard LED
2. DRAM LED
DRAM LED checks the DRAM in sequence during motherboard booting process. If an error is found , the LED next to the error device will continue lighting until the problem is solved. This user-friendly design provides an intuitional way to locate the root problem within a second.
DRAM LED
Z97M-PLUS
Z97M-PLUS DRAM LED
3. GPU Boost LED
The GPU Boost LED lights up when the GPU Boost switch is enabled.
GPU_LED
Z97M-PLUS
Z97M-PLUS GPU Boost LED
Chapter 1: Product introduction
1.2.9 Internal connectors
1. Intel
®
Z97 Serial ATA 6.0 Gb/s connectors (7-pin SATA6G_1-6)
These connectors connect to Serial ATA 6.0 Gb/s hard disk drives via Serial ATA 6.0
Gb/s signal cables.
If you installed Serial ATA hard disk drives, you can create a RAID 0, 1, 5, and 10 configuration with the Intel
®
Rapid Storage Technology through the onboard Intel
®
Z97 chipset.
A
SATA6G_1
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXN1
RSATA_RXP1
GND
SATA6G_2
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXN2
RSATA_RXP2
GND
B
SATA6G_3
GND
RSATA_TXP3
RSATA_TXN3
GND
RSATA_RXN3
RSATA_RXP3
GND
Z97M-PLUS
A
B
SATA6G_5
GND
RSATA_TXP5
RSATA_TXN5
GND
RSATA_RXN5
RSATA_RXP5
GND
Z97M-PLUS SATA 6.0Gb/s connectors
SATA6G_4
GND
RSATA_TXP4
RSATA_TXN4
GND
RSATA_RXN4
RSATA_RXP4
GND
SATA6G_6
GND
RSATA_TXP6
RSATA_TXN6
GND
RSATA_RXN6
RSATA_RXP6
GND
• These connectors are set to [AHCI] by default. If you intend to create a Serial ATA
RAID set using these connectors, set the SATA Mode Selection item in the BIOS to
[RAID]. Refer to section 3.6.3 PCH Storage Configuration for details.
• Before creating a RAID set, refer to section 5.1 RAID configurations or the manual bundled in the motherboard support DVD.
• When using hot-plug and NCQ, set the type of the SATA connectors in the BIOS to
[AHCI]
. See section 3.6.3 PCH Storage Configuration for details.
M.2 Socket 3 shares the bandwidth with SATA ports 5 and 6. To ensure that the M.2
PCIe device is working properly, SATA ports 5 and 6 are disabled. See section 3.6.3 PCH
Storage Configuration
of this user guide for more details.
ASUS Z97M-PLUS
1-15
1-16
2. USB 3.0 connector (20-1 pin USB3_12)
This connector allows you to connect a USB 3.0 module for additional USB 3.0 front or rear panel ports. With an installed USB 3.0 module, you can enjoy all the benefits of
USB 3.0 including faster data transfer speeds of up to 5Gbps, faster charging time for
USB-chargeable devices, optimized power efficiency, and backward compatibility with
USB 2.0.
Z97M-PLUS
USB3+5V
IntA_P2_SSRX-
IntA_P2_SSRX+
GND
IntA_P2_SSTX-
IntA_P2_SSTX+
GND
IntA_P2_D-
IntA_P2_D+
USB3_12
PIN 1
USB3+5V
IntA_P1_SSRX-
IntA_P1_SSRX+
GND
IntA_P1_SSTX-
IntA_P1_SSTX+
GND
IntA_P1_D-
IntA_P1_D+
GND
Z97M-PLUS USB3.0 Front panel connector
• The USB 3.0 module is purchased separately.
• These connectors are based on xHCI specification. We recommend you to install the related driver to fully use the USB 3.0 ports under Windows
®
7.
• The plugged USB 3.0 device may run on xHCI or EHCI mode depending on the operating system’s setting.
3. Serial port connector (10-1 pin COM)
This connector is for a serial (COM) port. Connect the serial port module cable to this connector, then install the module to a slot opening at the back of the system chassis.
COM
RXD DTR DSR CTS
PIN 1
DCD TXD GND RTS
Z97M-PLUS
Z97M-PLUS Serial port (COM) connector
The COM module is purchased separately.
Chapter 1: Product introduction
4. USB 2.0 connectors (10-1 pin USB910; USB1112; USB1314)
These connectors are for USB 2.0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0 specification that supports up to
480 Mbps connection speed.
USB910 USB1112 USB1314
USB+5V USB_P9- USB_P9+ GND NC USB+5V USB_P11- USB_P11+ GND NC
Z97M-PLUS
PIN 1 PIN 1
USB_P10- USB_P10+
Z97M-PLUS USB2.0 connectors
USB_P12- USB_P12+
PIN 1
USB+5V USB_P13- USB_P13+ GND NC
USB_P14- USB_P14+
Never connect a 1394 cable to the USB connectors. Doing so will damage the motherboard!
The USB 2.0 module is purchased separately.
5. Digital audio connector (4-1 pin SPDIF_OUT)
This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port. Connect the S/PDIF Out module cable to this connector, then install the module to a slot opening at the back of the system chassis.
Z97M-PLUS
SPDIFOUT GND
SPDIF_OUT
Z97M-PLUS Digital audio connector
The S/PDIF module is purchased separately.
ASUS Z97M-PLUS
1-17
1-18
6. CPU and chassis fan connectors (4-pin CPU_FAN; 4-pin CHA_FAN1/2)
Connect the fan cables to the fan connectors on the motherboard, ensuring that the black wire of each cable matches the ground pin of the connector.
CPU_FAN CHA_FAN2
CHA_FAN1
Z97M-PLUS
GND CHA FAN PWR CHA FAN IN CHA FAN PWM
Z97M-PLUS Fan connectors
• DO NOT forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. These are not jumpers!
Do not place jumper caps on the fan connectors!
• Ensure that the CPU fan cable is securely installed to the CPU fan connector.
• The CPU_FAN connector supports the CPU fan of maximum 1A (12 W) fan power.
• The CPU fan connector detects the type of CPU fan installed and automatically switches the control modes. To configure the CPU fan’s control mode, go to
Advanced Mode > Monitor > CPU Q-Fan Control
item in BIOS.
• The chassis fan connectors support DC and PWM modes. To set these fans to DC or
PWM, go to Advanced Mode > Monitor > Chassis Fan 1/2 Q-Fan Control items in
BIOS.
Chapter 1: Product introduction
7. Front panel audio connector (10-1 pin AAFP)
This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC`97 audio standard. Connect one end of the front panel audio I/O module cable to this connector.
AAFP
AGND NC SENSE1_RETUR
PIN 1
AGND NC NC
Z97M-PLUS
PORT1 L PORT1 R PORT2 R
HD-audio-compliant pin definition
Legacy AC’97 compliant definition
Z97M-PLUS Front panel audio connector
• We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard’s high-definition audio capability.
• If you want to connect a high-definition or an AC’97 front panel audio module to this connector, set the Front Panel Type item in the BIOS setup to [HD Audio] or [AC97].
8. TPM connector (20-1 pin TPM)
This connector supports a Trusted Platform Module (TPM) system, which securely store keys, digital certificates, passwords and data. A TPM system also helps enhance network security, protect digital identities, and ensures platform integrity.
Z97M-PLUS
TPM
LPCPD# GND +3VSB NC LAD0 +3V LAD3 LREST# LFRAME# LCLK
PIN 1
GND LAD1 LAD2
Z97M-PLUS TPM connector
The TPM module is purchased separately.
ASUS Z97M-PLUS
1-19
1-20
9. ATX power connectors (24-pin EATXPWR; 8-pin EATX12V)
These connectors are for ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit.
Z97M-PLUS
EATX12V
+12V DC +12V DC +12V DC +12V DC
GND GND GND GND
PIN 1
+3 Volts
+12 Volts
+12 Volts
+5V Standby
Power OK
GND
+5 Volts
GND
+5 Volts
GND
+3 Volts
+3 Volts
PIN 1
EATXPWR
GND
+5 Volts
+5 Volts
+5 Volts
-5 Volts
GND
GND
GND
PSON#
GND
-12 Volts
+3 Volts
Z97M-PLUS ATX power connectors
• For a fully configured system, we recommend that you use a power supply unit
(PSU) that complies with ATX 12V Specification 2.3 (or later version) and provides a minimum power of 350 W.
• DO NOT forget to connect the 4-pin/8-pin EATX12V power plug. Otherwise, the system will not boot.
• We recommend that you use a PSU with a higher power output when configuring a system with more power-consuming devices. The system may become unstable or may not boot up if the power is inadequate.
• If you want to use two high-end PCI Express x16 cards, use a PSU with 1000W power or above to ensure the system stability.
• If you are uncertain about the minimum power supply requirement for your system, refer to the Recommended Power Supply Wattage Calculator at http://support.asus.
com/PowerSupplyCalculator/PSCalculator.aspx?SLanguage=en-us for details.
10. LPT connector (26-1 pin LPT)
The LPT (Line Printing Terminal) connector supports devices such as a printer. LPT standardizes as IEEE 1284, which is the parallel port interface on IBM PC-compatible computers.
Z97M-PLUS
LPT
SLCT PE BUSY ACK# PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0 STB#
PIN 1
GND GND GND GND GND GND GND GND SLIN# INIT# ERR# AFD
Z97M-PLUS Parallel port connector
Chapter 1: Product introduction
11. System panel connector (20-8 pin PANEL)
This connector supports several chassis-mounted functions.
+PWR_LEDSPEAKER
+5V Ground Ground Speaker
PANEL
PIN 1
Z97M-PLUS
HDD_LED+ HDD_LED-
+HDD_LED- PWR_SW RESET
Z97M-PLUS System panel connector
• System power LED (2-pin +PWR_LED-)
This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode.
• Hard disk drive activity LED (2-pin +HDD_LED-)
This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED cable to this connector. The HDD LED lights up or flashes when data is read from or written to the HDD.
• System warning speaker (4-pin SPEAKER)
This 4-pin connector is for the chassis-mounted system warning speaker. The speaker allows you to hear system beeps and warnings.
• ATX power button/soft-off button (2-pin PWR_SW)
This connector is for the system power button. Pressing the power switch for more than four seconds while the system is ON turns the system OFF.
• Reset button (2-pin RESET)
This 2-pin connector is for the chassis-mounted reset button for system reboot without turning off the system power.
ASUS Z97M-PLUS
1-21
12. M.2 Socket 3
This socket allows you to install an M.2 (NGFF) SSD module.
M.2 (SOCKET3)
Z97M-PLUS
Z97M-PLUS M.2 socket
• This socket supports M Key and type 2242/2260/2280 storage devices (Type 2242 storage device is supported on Rev. 2.00 or later versions of this motherboard).
• The M.2 Socket 3 shares bandwidth with SATA ports 5 and 6. Refer to section 3.6.3
PCH Storage Configuration
of this user guide for more details.
• When using Intel ® Desktop Responsiveness technologies with PCIe M.2 device, ensure to set up the Windows
®
UEFI operating system under RAID mode.
The M.2 (NGFF) SSD module is purchased separately.
1-22 Chapter 1: Product introduction
Chapter 2: Basic installation
Basic installation
2.1 Building your PC system
2
2.1.1 Motherboard installation
The diagrams in this section are for reference only. The motherboard layout may vary with models, but the installation steps are the same for all models.
1. Install the ASUS I/O-shield to the chassis rear I/O panel.
2. Place the motherboard into the chassis, ensuring that its rear I/O ports are aligned to the chassis’ rear I/O panel.
ASUS Z97M-PLUS
2-1
3. Place six screws into the holes indicated by circles to secure the motherboard to the chassis.
Z97M-PLUS
2-2
DO NOT overtighten the screws! Doing so can damage the motherboard.
Chapter 2: Basic installation
2.1.2 CPU installation
Ensure that you install the correct CPU designed for LGA1150 socket only. DO NOT install a CPU designed for LGA1155 and LGA1156 socket on the LGA1150 socket.
ASUS Z97M-PLUS
2-3
2.1.3 CPU heatsink and fan assembly installation
Apply the Thermal Interface Material to the
CPU heatsink and CPU before you install the heatsink and fan, if necessary.
To install the CPU heatsink and fan assembly
2-4 Chapter 2: Basic installation
To uninstall the CPU heatsink and fan assembly
ASUS Z97M-PLUS
2-5
2.1.4 DIMM installation
2-6
To remove a DIMM
Chapter 2: Basic installation
2.1.5 ATX Power connection
OR OR
ASUS Z97M-PLUS
2-7
2.1.6 SATA device connection
OR
OR
2-8 Chapter 2: Basic installation
2.1.7 Front I/O Connector
To install the system panel connector
To install USB 2.0 connector To install front panel audio connector
AAFP
USB 2.0
To install USB 3.0 connector
USB 3.0
ASUS Z97M-PLUS
2-9
2.1.8 Expansion Card installation
To install PCIe x16 cards
To install PCI cards
2-10 Chapter 2: Basic installation
2.2 Motherboard rear and audio connections
2.2.1 Rear I/O connection
Rear panel connectors
1. PS/2 keyboard / mouse combo port
2. Video Graphics Adapter (VGA) port
3. Intel
®
LAN port*
4. USB 2.0 ports 7 and 8
5. DVI-D port
6. HDMI port
7. Intel USB 3.0 ports 5-6, support ASUS
USB 3.0 Boost
8. Intel USB 3.0 ports 3-4, support ASUS
USB 3.0 Boost
9. Audio I/O ports**
10.
* and **: Refer to the tables on the next page for LAN port LEDs, and audio port definitions.
ASUS Z97M-PLUS
2-11
2-12
• The plugged USB 3.0 device may run on xHCI mode or EHCI mode, depending on the operating system’s setting.
• USB 3.0 devices can only be used as data storage only.
• We strongly recommend that you connect USB 3.0 devices to USB 3.0 ports for faster and better performance for your USB 3.0 devices.
• Due to the design of the Intel
®
9 series chipset, all USB devices connected to the
USB 2.0 and USB 3.0 ports are controlled by the xHCI controller. Some legacy USB devices must update their firmware for better compatibility.
• Multi-VGA output supports up to three displays under Windows displays under BIOS, and one display under DOS.
® OS environment, two
• Due to design of the Intel ® display architecture, below are the following onboard graphics output and their maximum supported pixel clocks:
-
-
DVI port supports: 165 MHz
VGA port supports: 180 MHz
- HDMI port supports: 300 MHz
* LAN ports LED indications
Activity Link LED
Status Description
OFF
ORANGE
No link
Linked
Orange (Blinking) Data activity
Orange (Blinking then steady)
Ready to wake up from S5 mode
Speed LED
Status Description
OFF 10 Mbps connection
ORANGE 100 Mbps connection
GREEN 1 Gbps connection
ACT/LINK
LED
LAN port
SPEED
LED
** Audio 2.1, 4.1, 5.1, or 7.1-channel configuration
Port Headset
2.1-channel
Light Blue Line In
Lime Line Out
Pink
Orange
Mic In
–
Black
Gray
–
–
4.1-channel 5.1-channel 7.1-channel
Line In Line In Line In
Front Speaker Out Front Speaker Out Front Speaker Out
Mic In
–
Mic In
Center/Subwoofer
Mic In
Center/Subwoofer
Rear Speaker Out Rear Speaker Out Rear Speaker Out
– – Side Speaker Out
Chapter 2: Basic installation
2.2.2 Audio I/O connections
Audio I/O ports
Connect to Headphone and Mic
Connect to Stereo Speakers
Connect to 2.1 channel Speakers
ASUS Z97M-PLUS
2-13
Connect to 4.1 channel Speakers
Connect to 5.1 channel Speakers
2-14
Connect to 7.1 channel Speakers
Chapter 2: Basic installation
2.3 Starting up for the first time
1. After making all the connections, replace the system case cover.
2. Ensure that all switches are off.
3. Connect the power cord to the power connector at the back of the system chassis.
4. Connect the power cord to a power outlet that is equipped with a surge protector.
5. Turn on the devices in the following order:
a. Monitor b. External SCSI devices (starting with the last device on the chain) c. System power
6. After applying power, the system power LED on the system front panel case lights up.
For systems with ATX power supplies, the system LED lights up when you press the
ATX power button. If your monitor complies with the “green” standards or if it has a
“power standby” feature, the monitor LED may light up or change from orange to green after the system LED turns on.
The system then runs the power-on self tests (POST). While the tests are running, the
BIOS beeps (refer to the BIOS beep codes table) or additional messages appear on the screen. If you do not see anything within 30 seconds from the time you turned on the power, the system may have failed a power-on test. Check the jumper settings and connections or call your retailer for assistance.
BIOS Beep
One short beep
Description
VGA detected
Quick boot set to disabled
No keyboard detected
No memory detected One continuous beep followed by two short beeps then a pause (repeated)
One continuous beep followed by three short beeps
One continuous beep followed by four short beeps
No VGA detected
Hardware component failure
7. At power on, hold down the <Delete> key to enter the BIOS Setup. Follow the instructions in Chapter 3.
2.4 Turning off the computer
While the system is ON, press the power button for less than four seconds to put the system on sleep mode or soft-off mode, depending on the BIOS setting. Press the power switch for more than four seconds to let the system enter the soft-off mode regardless of the BIOS setting.
ASUS Z97M-PLUS
2-15
2-16 Chapter 2: Basic installation
Chapter 3: BIOS setup
BIOS setup
3.1 Knowing BIOS
3
The new ASUS UEFI BIOS is a Unified Extensible Interface that complies with UEFI architecture, offering a user-friendly interface that goes beyond the traditional keyboardonly BIOS controls to enable a more flexible and convenient mouse input. You can easily navigate the new UEFI BIOS with the same smoothness as your operating system. The term “BIOS” in this user manual refers to “UEFI BIOS” unless otherwise specified.
BIOS (Basic Input and Output System) stores system hardware settings such as storage device configuration, overclocking settings, advanced power management, and boot device configuration that are needed for system startup in the motherboard CMOS. In normal circumstances, the default BIOS settings apply to most conditions to ensure optimal performance. DO NOT change the default BIOS settings except in the following circumstances:
• An error message appears on the screen during the system bootup and requests you to run the BIOS Setup.
• You have installed a new system component that requires further BIOS settings or update.
Inappropriate BIOS settings may result to instability or boot failure. We strongly
recommend that you change the BIOS settings only with the help of a trained service personnel
.
When downloading or updating the BIOS file, rename it as Z97MPLUS.CAP for this motherboard.
ASUS Z97M-PLUS
3-1
3-2
3.2 BIOS setup program
Use the BIOS Setup to update the BIOS or configure its parameters. The BIOS screen include navigation keys and brief onscreen help to guide you in using the BIOS Setup program.
Entering BIOS at startup
To enter BIOS Setup at startup, press <Delete> or <F2> during the Power-On Self Test
(POST). If you do not press <Delete> or <F2>, POST continues with its routines.
•
•
•
Entering BIOS Setup after POST
To enter BIOS Setup after POST:
Press <Ctrl>+<Alt>+<Delete> simultaneously.
Press the reset button on the system chassis.
Press the power button to turn the system off then back on. Do this option only if you failed to enter BIOS Setup using the first two options.
• The BIOS setup screens shown in this section are for reference purposes only, and may not exactly match what you see on your screen.
• Ensure that a USB mouse is connected to your motherboard if you want to use the mouse to control the BIOS setup program.
• If the system becomes unstable after changing any BIOS setting, load the default settings to ensure system compatibility and stability. Select the Load Optimized
Defaults
item under the Exit menu or press hotkey <F5>. See section 3.10 Exit Menu for details.
• If the system fails to boot after changing any BIOS setting, try to clear the CMOS and reset the motherboard to the default value. See section 1.2.6 Jumpers for information on how to erase the RTC RAM.
• The BIOS setup program does not support the bluetooth devices.
BIOS menu screen
The BIOS Setup program can be used under two modes: EZ Mode and Advanced Mode.
Press <F7> to change between the two modes.
Chapter 3: BIOS setup
3.2.1 EZ Mode
By default, the EZ Mode screen appears when you enter the BIOS setup program. The EZ
Mode provides you an overview of the basic system information, and allows you to select the display language, system performance mode, fan profile and boot device priority. To access the Advanced Mode, click Advanced Mode(F7) or press <F7>.
The default screen for entering the BIOS setup program can be changed. Refer to the
Setup Mode
item in section 3.8 Boot menu for details.
Displays the system properties of the selected mode.
Click < or > to switch EZ System Tuning modes
Displays the CPU/motherboard temperature,
CPU voltage output, CPU/chassis fan speed, and SATA information
Selects the display language of the BIOS setup program
Creates storage RAID and configures system overclocking
Enables or disables the SATA RAID mode for Intel Rapid Storage Technology
Displays the CPU Fan’s speed. Click the button to manually tune the fans
Loads optimized default settings
Shows the bootable devices
Saves the changes and resets the system
Displays the Advanced mode menus
Selects the boot device priority
The boot device options vary depending on the devices you installed to the system.
ASUS Z97M-PLUS
3-3
3.2.2 Advanced Mode
The Advanced Mode provides advanced options for experienced end-users to configure the BIOS settings. The figure below shows an example of the Advanced Mode. Refer to the following sections for the detailed configurations.
To access the EZ Mode, click EzMode(F7) or press <F7>.
Menu bar
Language
Q-Fan control
MyFavorite
EZ Tuning Wizard
Quick Note
Hot Keys
3-4
Sub-menu item
Menu items
Item description Configuration fields
Scroll bar Last modified settings
Goes back to EZ Mode
Displays the CPU/motherboard temperature,
CPU and memory voltage output
Chapter 3: BIOS setup
Menu bar
The menu bar on top of the screen has the following main items:
My Favorites
For saving the frequently-used system settings and configuration.
Main
For changing the basic system configuration
Ai Tweaker
For changing the overclocking settings
Advanced
For changing the advanced system settings
Monitor
For displaying the system temperature, power status, and changing the fan settings.
Boot
Tool
Exit
For changing the system boot configuration
For configuring options for special functions
For selecting the exit options and loading default settings
Menu items
The highlighted item on the menu bar displays the specific items for that menu. For example, selecting Main shows the Main menu items.
The other items (My Favorites, Ai Tweaker, Advanced, Monitor, Boot, Tool, and Exit) on the menu bar have their respective menu items.
Submenu items
A greater than sign (>) before each item on any menu screen means that the item has a submenu. To display the submenu, select the item and press <Enter>.
Language
This button above the menu bar contains the languages that you can select for your BIOS.
Click this button to select the the language that you want to display in your BIOS screen.
MyFavorites (F3)
This button above the menu bar shows all BIOS items in a Tree Map setup. Select frequentlyused BIOS settings and save it to MyFavorites menu.
Refer to section 3.3 My Favorites for more information.
Q-Fan Control (F6)
This button above the menu bar displays the current settings of your fans. Use this button to manually tweak the fans to your desired settings.
Refer to section 3.2.3 QFan Control for more information.
EZ Tuning Wizard (F11)
This button above the menu bar allows you to view and tweak the overclocking settings of your system. It also allows you to change the motherboard’s SATA mode from AHCI to RAID mode.
Refer to section 3.2.4 EZ Tuning Wizard for more information.
ASUS Z97M-PLUS
3-5
3-6
Quick Note (F9)
This button above the menu bar allows you to key in notes of the activities that you have done in BIOS.
• The Quick Note function does not support the following keyboard functions: delete, cut, copy and paste.
• You can only use the alphanumeric characters to enter your notes.
Hot keys
This button above the menu bar contains the navigation keys for the BIOS setup program.
Use the navigation keys to select items in the menu and change the settings.
Scroll bar
A scroll bar appears on the right side of a menu screen when there are items that do not fit on the screen. Press the Up/Down arrow keys or <Page Up> / <Page Down> keys to display the other items on the screen.
General help
At the top right corner of the menu screen is a brief description of the selected item. Use
<F12> key to capture the BIOS screen and save it to the removable storage device.
Configuration fields
These fields show the values for the menu items. If an item is user-configurable, you can change the value of the field opposite the item. You cannot select an item that is not user-configurable.
A configurable field is highlighted when selected. To change the value of a field, select it and press <Enter> to display a list of options.
Last Modified button
This button shows the items that you last modified and saved in BIOS Setup.
Chapter 3: BIOS setup
3.2.3 QFan Control
The QFan Control allows you to set a fan profile or manually configure the operating speed of your CPU and chassis fans.
Click to select a fan to be configured
Click to activate
PWM Mode
Click to activate DC Mode
Select a profile to apply to your fans
Click to apply the fan setting
Click to undo the changes
Click to go back to main menu
Select to manually configure your fans
ASUS Z97M-PLUS
3-7
Configuring fans manually
Select Manual from the list of profiles to manually configure your fans’ operating speed.
3-8
Speed points
Click or tap to manually configure your fans
To configure your fans:
1. Select the fan that you want to configure and to view its current status.
2. Click and drag the speed points to adjust the fans’ operating speed.
3. Click Apply to save the changes then click Exit (ESC).
Chapter 3: BIOS setup
3.2.4 EZ Tuning Wizard
EZ Tuning Wizard allows you to overclock your CPU and DRAM, computer usage, and CPU fan to their best settings. You can also easily set RAID in your system using this feature.
System OC setup RAID setup
Tuning your system settings
To tune your settings:
1. Press <F11> on your keyboard or click
EZ Tuning Wizard screen, then click Next.
from the BIOS screen to open
2. Select a PC scenario Daily Computing or Gaming/Media Editing, then click Next.
3. Select the CPU fan type (Box cooler, Tower cooler, or Water cooler) that you installed then click Next.
If you are not sure of the CPU fan type, click I’m not sure. The system automatically detects the CPU fan type.
4. Click Next then click Yes to confirm auto-tuning.
ASUS Z97M-PLUS
3-9
3-10
Creating RAID
To create RAID:
1. Press <F11> on your keyboard or click
EZ Tuning Wizard screen.
2. Click RAID then click Next.
from the BIOS screen to open
• Ensure that your HDDs have no existing RAID volumes.
• Ensure to connect your HDDs to Intel ® SATA connectors.
3. Select the type of storage for your RAID Easy Backup or Super Speed, then click
Next
.
a. For Easy Backup, click
Next
then select from Easy
Backup (RAID1)
or Easy
Backup (RAID10)
.
You can only select Easy
Backup (RAID 10) if you connect four (4) HDDs.
b. For Easy Backup, click Next then select from Super
Speed (RAID0)
or Super
Speed (RAID5)
.
4. After selecting the type of RAID, click Next then click Yes to continue the RAID setup.
5. After the RAID setup is done, click Yes to exit the setup then click OK to reset your system.
Chapter 3: BIOS setup
3.3 My Favorites
MyFavorites is your personal space where you can easily save and access your favorite
BIOS items.
ASUS Z97M-PLUS
3-11
3-12
Adding items to My Favorites
To add BIOS items:
1. Press <F3> on your keyboard or click
Setup Tree Map screen.
from the BIOS screen to open
2. On the Setup Tree Map screen, select the BIOS items that you want to save in
MyFavorites screen.
Main menu panel
Submenu panel
Selected shortcut items
3. Select an item from main menu panel, then click the submenu that you want to save as favorite from the submenu panel and tap or click or press <Enter> on your keyboard.
You cannot add the following items to My Favorite items:
• Items with submenu options
• User-managed items such as language and boot order
• Configuration items such as Memory SPD Information, system time and date.
4. Click Exit (ESC) or press <esc> key to close Setup Tree Map screen.
5. Go to My Favorites menu to view the saved BIOS items.
Chapter 3: BIOS setup
3.4 Main menu
The Main menu screen appears when you enter the Advanced Mode of the BIOS Setup program. The Main menu provides you an overview of the basic system information, and allows you to set the system date, time, language, and security settings.
Security
The Security menu items allow you to change the system security settings.
• If you have forgotten your BIOS password, erase the CMOS Real Time Clock (RTC)
RAM to clear the BIOS password. See section 1.2.6 Jumpers for information on how to erase the RTC RAM via the Clear CMOS button.
• The Administrator or User Password items on top of the screen show the default [Not
Installed]
. After you set a password, these items show [Installed].
ASUS Z97M-PLUS
3-13
3-14
Administrator Password
If you have set an administrator password, we recommend that you enter the administrator password for accessing the system. Otherwise, you might be able to see or change only selected fields in the BIOS setup program.
To set an administrator password:
1. Select the Administrator Password item and press <Enter>.
2. From the Create New Password box, key in a password, then press <Enter>.
3. Confirm the password when prompted.
To change an administrator password:
1. Select the Administrator Password item and press <Enter>.
2. From the Enter Current Password box, key in the current password, then press
<Enter>.
3. From the Create New Password box, key in a new password, then press <Enter>.
4. Confirm the password when prompted.
To clear the administrator password, follow the same steps as in changing an administrator password, but press <Enter> when prompted to create/confirm the password. After you clear the password, the Administrator Password item on top of the screen shows Not Installed.
User Password
If you have set a user password, you must enter the user password for accessing the system.
The User Password item on top of the screen shows the default Not Installed. After you set a password, this item shows Installed.
To set a user password:
1. Select the User Password item and press <Enter>.
2. From the Create New Password box, key in a password, then press <Enter>.
3. Confirm the password when prompted.
To change a user password:
1. Select the User Password item and press <Enter>.
2. From the Enter Current Password box, key in the current password, then press
<Enter>.
3. From the Create New Password box, key in a new password, then press <Enter>.
4. Confirm the password when prompted.
To clear the user password, follow the same steps as in changing a user password, but press
<Enter> when prompted to create/confirm the password. After you clear the password, the
User Password
item on top of the screen shows Not Installed.
Chapter 3: BIOS setup
3.5 Ai Tweaker menu
The Ai Tweaker menu items allow you to configure overclocking-related items.
Be cautious when changing the settings of the Ai Tweaker menu items. Incorrect field values can cause the system to malfunction.
The configuration options for this section vary depending on the CPU and DIMM model you installed on the motherboard.
Scroll down to display other BIOS items.
Ai Overclock Tuner [Auto]
This item allows you to select the CPU overclocking options to achieve the desired CPU internal frequency. Select any of these preset overclocking configuration options:
[Auto]
[Manual]
Loads the optimal settings for the system.
Automatically optimizes the CPU ratio and BCLK frequency.
The following two items appear only when you set the Ai Overclocking Tuner to [Manual].
Filter PLL [Auto]
Set this item to high BCLK (base clock) mode when using a very high BCLK to improve overclocking capability. Configuration options: [Auto] [Low BCLK mode] [High BCLK mode]
ASUS Z97M-PLUS
3-15
3-16
BCLK Frequency [Auto]
This item allows you to set the BCLK (base clock) frequency to enhance the system performance. Use the <+> or <-> to adjust the value. The values range from 80.0 MHz to 300.0 MHz.
We recommend you to set the value based on the CPU specification, as high BCLK frequencies may damage the CPU permanently.
[Auto]
Initial BCLK Frequency [Auto]
This item allows you to start overclocking the system from the initial BCLK (base clock) frequency to the assigned BCLK frequency. Use the <+> or <-> to adjust the value.
The value ranges depend on the value you set on BCLK Frequency.
ASUS MultiCore Enhancement [Auto]
[Disabled]
This item allows you to maximize the oveclocking performance optimized by ASUS core ratio settings.
This item allows you to set to default core ratio settings.
CPU Core Ratio [Auto]
This item allows you to set the CPU core ratio limit per core or synchronize automatically to all cores. Configuration options: [Auto] [Sync All Cores] [Per Core]
When the CPU Core Ratio is set to [Per Core], the following items appear:
1-Core Ratio Limit [Auto]
Select [Auto] to apply the CPU default Turbo Ratio setting or manually assign a 1-Core Limit value that must be higher than or equal to the 2-Core
Ratio Limit.
2-Core Ratio Limit [Auto]
Select [Auto] to apply the CPU default Turbo Ratio setting or manually assign a 2-Core Limit value that must be higher than or equal to the 3-Core
Ratio Limit.
If you assign a value for 2-Core Ratio Limit, do not set the 1-Core Ratio Limit to [Auto].
3-Core Ratio Limit [Auto]
Select [Auto] to apply the CPU default Turbo Ratio setting or manually assign a 3-Core Limit value that must be higher than or equal to the 4-Core
Ratio Limit.
If you assign a value for 3-Core Ratio Limit, do not set the 1-Core Ratio Limit and 2-Core
Ratio Limit to [Auto].
4-Core Ratio Limit [Auto]
Select [Auto] to apply the CPU default Turbo Ratio setting or manually assign a 4-Core Limit value that must be higher than or equal to the 3-Core
Ratio Limit.
If you assign a value for 4-Core Ratio Limit, do not set the 1-Core Ratio Limit, 2-Core Ratio
Limit, and 3-Core Ratio to [Auto].
Chapter 3: BIOS setup
Min. CPU Cache Ratio [Auto]
This item allows you to set the minimum possible ratio on the Uncore part of the processor.
Use the <+> or <-> keys to adjust the value. The values depend on the CPU installed.
Max. CPU Cache Ratio [Auto]
This item allows you to set the maximum possible ratio on the Uncore part of the processor.
Use the <+> or <-> keys to adjust the value. The values depend on the CPU installed.
Internal PLL Overvoltage [Auto]
Allows you to enable the internal PLL Overvoltage for K-SKU CPUs to get the extreme overclocking capability. Configuration options: [Auto] [Enabled] [Disabled]
BCLK Frequency: DRAM Frequency Ratio [Auto]
[Auto]
[100:133]
[100:100]
The BCLK frequency to DRAM frequency ratio is set to the optimized settings.
The BCLK frequency to DRAM frequency ratio is set to 100:133.
The BCLK frequency to DRAM frequency ratio is set to 100:100.
Memory Frequency [Auto]
This item allows you to set the memory operating frequency. The configurable options vary with the BCLK (base clock) frequency setting. Select the auto mode to apply the optimized setting. Configuration options: [DDR3-800MHz] [DDR3-1066MHz] [DDR3-1333MHz]
[DDR3-1400MHz] [DDR3-1600MHz] [DDR3-1800MHz] [DDR3-1866MHz] [DDR3-2000MHz]
[DDR3-2133MHz] [DDR3-2200MHz] [DDR3-2400MHz] [DDR3-2600MHz] [DDR3-2666MHz]
[DDR3-2800MHz] [DDR3-2933MHz] [DDR3-3000MHz] [DDR3-3200MHz] [DDR3-3400MHz]
Max. CPU Graphics Ratio [Auto]
Allows you to set the CPU Graphics ratio. Use <+>/<-> to adjust the value. The ratio may vary depending on the system loading.
OC Tuner [Keep Current Settings]
This item allows you to automatically overclock the CPU and DRAM frequencies and voltage for an enhanced system performance. It also accelerates the CPU graphics performance to the extreme depending on the CPU graphics loading. Configuration options: [Keep Current
Settings] [Ratio First] [BCLK First]
Ensure that you installed an efficient CPU fan for CPU and graphics loading before selecting either [BCLK First] or [Ratio First]. To keep the current overclocking tuner status, select [Keep Current Settings].
EPU Power Saving Mode [Disabled]
The ASUS EPU (Energy Processing Unit) sets the CPU in its minimum power consumption settings. Enable this item to set lower CPU VCCIN and Vcore voltages and achieve the best energy saving condition. Configuration options: [Disabled] [Enabled]
ASUS Z97M-PLUS
3-17
3-18
DRAM Timing Control
The subitems in this menu allow you to set the DRAM timing control features. Use the <+> or <-> keys to adjust the value. To restore the default setting, type [auto] using the keyboard and press the <Enter> key.
Changing the values in this menu may cause the system to become unstable! If this happens, revert to the default settings.
Primary Timings
DRAM CAS# Latency [Auto]
Configuration options: [Auto] [1] – [31]
DRAM RAS# to CAS# Delay [Auto]
Configuration options: [Auto] [1] – [31]
DRAM RAS# PRE Time [Auto]
Configuration options: [Auto] [1] – [31]
DRAM RAS# ACT Time [Auto]
Configuration options: [Auto] [1] – [63]
DRAM COMMAND Rate [Auto]
Configuration options: [Auto] [1] [2]
Secondary Timings
DRAM RAS# to RAS# Delay [Auto]
Configuration options: [Auto] [1] – [15]
DRAM REF Cycle Time [Auto]
Configuration options: [Auto] [1] – [511]
DRAM Refresh Interval [Auto]
Configuration options: [Auto] [1] – [65535]
DRAM WRITE Recovery Time [Auto]
Configuration options: [Auto] [1] – [16]
DRAM READ to PRE Time [Auto]
Configuration options: [Auto] [1] – [15]
DRAM FOUR ACT WIN Time [Auto]
Configuration options: [Auto] [1] – [255]
DRAM WRITE to READ Delay [Auto]
Configuration options: [Auto] [1] – [15]
DRAM CKE Minimum Pulse Width [Auto]
Configuration options: [Auto] [1] – [15]
DRAM CAS# Write Latency [Auto]
Configuration options: [Auto] [1] – [31]
Chapter 3: BIOS setup
RTL IOL control
DRAM RTL Initial Value [Auto]
Configuration options: [Auto] [1] – [63]
DRAM RTL (CHA_R0D0) [Auto]
Configuration options: [Auto] [1] - [63]
DRAM RTL (CHA_R0D1) [Auto]
Configuration options: [Auto] [1] - [63]
DRAM RTL (CHA_R1D0) [Auto]
Configuration options: [Auto] [1] - [63]
DRAM RTL (CHA_R1D1) [Auto]
Configuration options: [Auto] [1] - [63]
DRAM RTL (CHB_R0D0) [Auto]
Configuration options: [Auto] [1] - [63]
DRAM RTL (CHB_R0D1) [Auto]
Configuration options: [Auto] [1] - [63]
DRAM RTL (CHB_R1D0) [Auto]
Configuration options: [Auto] [1] - [63]
DRAM RTL (CHB_R1D1) [Auto]
Configuration options: [Auto] [1] - [63]
DRAM IO-L (CHA_R0D0) [Auto]
Configuration options: [Auto] [1] - [15]
DRAM IO-L (CHA_R0D1) [Auto]
Configuration options: [Auto] [1] - [15]
DRAM IO-L (CHA_R1D0) [Auto]
Configuration options: [Auto] [1] - [15]
DRAM IO-L (CHA_R1D1) [Auto]
Configuration options: [Auto] [1] - [15]
DRAM IO-L (CHB_R0D0) [Auto]
Configuration options: [Auto] [1] - [15]
DRAM IO-L (CHB_R0D1) [Auto]
Configuration options: [Auto] [1] - [15]
DRAM IO-L (CHB_R1D0) [Auto]
Configuration options: [Auto] [1] - [15]
DRAM IO-L (CHB_R1D1) [Auto]
Configuration options: [Auto] [1] - [15]
Third Timings tRDRD [Auto]
Configuration options: [Auto] [1] – [7]
tRDRD_dr [Auto]
Configuration options: [Auto] [1] – [15]
tRDRD_dd [Auto]
Configuration options: [Auto] [1] – [15]
tWRRD [Auto]
Configuration options: [Auto] [1] – [63]
ASUS Z97M-PLUS
3-19
3-20
tWRRD_dr [Auto]
Configuration options: [Auto] [1] – [15]
tWRRD_dd [Auto]
Configuration options: [Auto] [1] – [15]
tWRWR [Auto]
Configuration options: [Auto] [1] – [7]
tWRWR_dr [Auto]
Configuration options: [Auto] [1] – [15]
tWRWR_dd [Auto]
Configuration options: [Auto] [1] – [15]
Dec_WRD
Configuration options: [Auto] [0] [1]
tRDWR [Auto]
Configuration options: [Auto] [1] – [31]
tRDWR_dr [Auto]
Configuration options: [Auto] [1] – [31]
tRDWR_dd [Auto]
Configuration options: [Auto] [1] – [31]
MISC
MRC Fast Boot [Auto]
This item allows you to enable, disable or automatically set the MRC fast boot.
Configuration options: [Auto] [Enabled] [Disabled]
DRAM CLK Period [Auto]
This item allows you to set a DRAM clock period. Configuration options: [Auto] [1] –
[14]
Channel A/B DIMM Control [Enable Both DIMMs]
This item allows you to enable or disable the DIMMs on channels A and B.
Configuration options: [Enable Both DIMMS] [Disable DIMM0] [Disable DIMM1]
[Disable Both DIMMS]
Scrambler Setting [Optimized (ASUS)]
This item allows you to set the optimized mode to enhance system stability.
Configuration options: [Optimized (ASUS] [Default (MRC)]
MCH Full Check [Auto]
Enable this item to enhance the stability of your system. Disable this item to enhance the DRAM overclocking capability. Configuration options: [Auto] [Enabled] [Disabled]
Chapter 3: BIOS setup
Skew Control
Changing subitems in this menu may enhance the DRAM overclocking capability and stability.
Transmitter Rising Slope [Auto]
Configuration options: [Auto] [0] – [31]
Transmitter Falling Slope [Auto]
Configuration options: [Auto] [0] – [31]
Transmitter Control Time [Auto]
Configuration options: [Auto] [0] – [31]
Receiver Rising Slope [Auto]
Configuration options: [Auto] [0] – [31]
Receiver Falling Slope [Auto]
Configuration options: [Auto] [0] – [31]
Receiver Control Time [Auto]
Configuration options: [Auto] [0] – [31]
DIGI+ VRM
CPU Load-line Calibration [Auto]
Load-line is defined by Intel ® specification and affects CPU power voltage. The CPU working voltage decreases proportionally to CPU loading. Higher load-line calibration could get higher voltage and good overclocking performance, but increases the CPU and VRM thermal conditions. Configuration options: [Auto] [Regular] [Medium] [High]
[Ultra High] [Extreme]
The actual performance boost may vary depending on your CPU specification.
DO NOT remove the thermal module. The thermal conditions should be monitored.
CPU VRM Switching Frequency [Auto]
This item affects the VRM transient response speed and the component thermal production. Select [Manual] to configure a higher frequency for a quicker transient response speed. Configuration options: [Auto] [Manual]
DO NOT remove the thermal module. The thermal conditions should be monitored.
The following item appears only when you set the CPU VRM Switching Frequency to
[Manual]
.
Fixed CPU VRM Switching Frequency (KHz) [250]
This item allows you to set a higher frequency for a quicker transient response speed. Use the <+> or <-> to adjust the value. The values range from 200 KHz to 350 KHz with an interval of 50 KHz.
ASUS Z97M-PLUS
3-21
3-22
CPU Power Phase Control [Auto]
This item allows you to set the power phase control of the CPU. Configuration options:
[Auto] [Standard] [Optimized] [Extreme] [Power Phase Response]
DO NOT remove the thermal module when setting this item to [Power Phase Response].
The thermal conditions should be monitored.
The following item appears only when you set the CPU Power Phase Control to [Power
Phase Response]
.
Power Phase Response [Fast]
This item allows you to set a faster phase response for the CPU to increase system performance or to slower phase response to decrease
DRAM power efficiency. Configuration options: [Ultra Fast] [Fast] [Medium]
[Regular]
CPU Power Duty Control [T.Probe]
DIGI + VRM Duty Control adjusts the current of every VRM phase and the thermal conditions of every phase component.
[T. Probe]
[Extreme]
Select to maintain the VRM thermal balance.
Select to maintain the current VRM balance.
DO NOT remove the thermal module. The thermal conditions should be monitored.
CPU Current Capability [Auto]
This item provides a total power range for CPU overclocking. A higher value setting provides higher power consumption delivery and extends the overclocking frequency range simultaneously. Configuration options: [Auto] [100%] [110%] [120%] [130%]
[140%]
Internal CPU Power Management
The subitems in this menu allow you to set the CPU ratio and their features.
Enhanced Intel SpeedStep Technology [Enabled]
This item allows the operating system to dynamically adjust the processor voltage and cores frequency, resulting to a decreased average power consumption and decreased average heat production.
Configuration options: [Disabled] [Enabled]
Turbo Mode [Enabled]
This item allows you to enable your core processor’s speed to run faster than the base operating frequency when it is below operating power, current and temperature specification limit. Configuration options: [Disabled] [Enabled]
The following items appear only when you set the Turbo Mode to [Enabled].
Turbo Mode Parameters
Long Duration Package Power Limit [Auto]
Allows you to limit the Turbo Ratio’s time duration that exceeds the TDP
(Thermal Design Power) for maximum performance. Use the <+> or <-> keys to adjust the value. The values range from 1 W to 4096 W.
Chapter 3: BIOS setup
Package Power Time Window [Auto]
Also known as Power Limit 1, this item allows you to maintain the time window for Turbo Ratio over TDP (Thermal Design Power). Use the <+> or
<-> keys to adjust the value. The values range from 1 to 127 in seconds.
Short Duration Package Power Limit [Auto]
Also known as Power Limit 2, this item allows you to provide rapid protection when the package power exceeds the Power Limit 1. Use the
<+> or <-> keys to adjust the value. The values range from 1 W to 4096 W.
CPU Integrated VR Current Limit [Auto]
Allows you to set a higher current limit to prevent frequency and power throttling when overclocking. Use the <+> or <-> keys to adjust the value.
The values range from 0.125 to 1023.875 with a 0.125 interval.
CPU Internal Power Switching Frequency
Frequency Tuning Mode [Auto]
This item allows you to increase or decrease the switching frequency of the internal regulator. Decrease the switching frequency to reduce the power consumption or increase the switching frequency to enhance voltage stability. When this item is set to
[+]
or [-], the Frequency Tuning Offset appears that allows you to set its value from 0% to 6%.
CPU Internal Power Fault Control
Thermal Feedback [Auto]
Allows your system to take precautionary actions to protect the CPU when the thermal condition of the external regulator exceeds the threshold. Configuration options: [Auto]
[Disabled] [Enabled]
CPU Integrated VR Fault Management [Auto]
Disable this item to prevent tripping the Fully Integrated Voltage Regulator when doing over-voltage. We recommend you to disable this item when overclocking. Configuration options: [Auto] [Disabled] [Enabled]
CPU Internal Power Configuration
CPU Integrated VR Efficiency Management [Auto]
This item allows you to improve the power rating when the CPU is in low power state, or make the FIVR (fully integrated voltage regulator work in high performance at all times. Configuration options: [Auto] [High Performance] [Balanced]
Power Decay Mode [Auto]
This item allows your system to improve the power saving mode on the Fully Integrated
Voltage Regulator as the processor goes into low current state. Configuration options:
[Auto] [Disabled] [Enabled]
Idle Power-in Response [Auto]
This item allows you to set the slew rate for the Fully Integrated Voltage Regulator when it enters manual override mode. Configuration options: [Auto] [Regular] [Fast]
ASUS Z97M-PLUS
3-23
3-24
Idle Power-out Response [Auto]
This item allows you to set the slew rate for the Fully Integrated Voltage Regulator when it exits manual override mode. Configuration options: [Auto] [Regular] [Fast]
Power Current Slope [Auto]
This item allows you to enhance the power saving condition or the system overclocking capabiltity. Select a higher power current slope levels for power saving enhancement or lower power current slope levels for system overclocking enhancement.
Configuration options: [Auto] [LEVEL -4] - [LEVEL 4]
Power Current Offset [Auto]
This item allows you to increase or decrease the output current sensed by the CPU. It finds the balance between optimal regulating while staying below the current threshold.
Configuration options: [Auto] [100%] [87.5%] [75.0%] [62.5%] [50.0%] [37.5%] [25.0%]
[12.5%] [0%] [-12.5%] [-25.0%] [-37.5%] [-50.0%] [-62.5%] [-75.0%] [-87.5%] [-100%]
Power Fast Ramp Response [Auto]
This item allows you to enhance the response of the CPU voltage regulator during the load transients. Use the <+> or <-> to adjust the value. The values range from 0.00 to
1.50. Configuration options: [Auto] [0.00] - [1.50]
CPU Internal Power Saving Control
Power Saving Level 1 Threshold [Auto]
Lower value provides sufficient overclocking tolerance to enlarge the overclocking potential. Higher value provides better power-saving condition.Use <+> or <-> key to adjust the value. The values range from 0 A to 80 A at 1 A increment.
Power Saving Level 2 Threshold [Auto]
Lower value provides sufficient overclocking tolerance to enlarge the overclocking potential. Higher value provides better power-saving condition.Use <+> or <-> key to adjust the value. The values range from 0 A to 50 A at 1 A increment.
Power Saving Level 3 Threshold [Auto]
Lower value provides sufficient overclocking tolerance to enlarge the overclocking potential. Higher value provides better power-saving condition.Use <+> or <-> key to adjust the value. The values range from 0 A to 30 A at 1A increment.
Extreme Over-voltage [Disabled]
This item allows you to set higher voltages for overclocking. When you enable this item, you can choose a high level voltage to overclock, but does not guarantee the CPU life.
Configuration options: [Enabled] [Disabled]
CPU Core Voltage [Auto]
This item allows you to configure the amount of voltage fed to the CPU cores. Increase the voltage when setting a high Core Frequency value. Configuration options: [Auto] [Manual
Mode] [Offset Mode] [Adaptive Mode]
• The following item appears only when you set the CPU Core Voltage to [Manual
Mode]
.
• [Adaptive Mode] is available for some specific CPU types.
Chapter 3: BIOS setup
CPU Core Voltage Override [Auto]
Allows you to set the CPU Core Voltage override. Use the <+> or <-> keys to adjust the value. The values range from 0.001V to 1.920V with a 0.001V interval.
The following items appear only when you set the CPU Core Voltage to [Offset Mode] or
[Adaptive Mode]
.
Offset Mode Sign [+]
[+] To offset the voltage by a positive value.
[–] To offset the voltage by a negative value.
CPU Core Voltage Offset
Use the <+> or <-> keys to adjust the value. The values range from 0.001V to 0.999V with a 0.001V interval.
The following item appears only when you set the CPU Core Voltage to [Adaptive Mode].
Additional Turbo Mode CPU Core Voltage [Auto]
This item allows you to set the amount of voltage fed to the CPU cores when running in turbo mode. Increase the voltage when configuring a high CPU core frequency. The voltage you set is affected by the offset value. Use the <+> or <-> keys to adjust the value. The values range from 0.001V to 1.920 V with a 0.001 V interval.
Total Adaptive Mode CPU Core Voltage [Auto]
This item sums up the voltages of the CPU Core Voltage offset and Additional Turbo
Mode CPU Core Voltage options.
CPU Cache Voltage [Auto]
This item allows you to set the amount of voltage fed to the CPU uncores including its cache.
Increase the voltage when setting a high CPU cache frequency. Configuration options: [Auto]
[Manual Mode] [Offset Mode] [Adaptive Mode]
• The following item appears only when you set the CPU Cache Voltage to [Manual
Mode]
.
• [Adaptive Mode] is available for some specific CPU types.
CPU Cache Voltage Override [Auto]
This item allows you to set the CPU Cache Voltage override. By default, this item takes the standard value of the installed CPU. You can use the <+> or <-> keys to adjust the value. The values range from 0.001V to 1.920 V with a 0.001 V interval.
The following items appear only when you set the CPU Core Voltage to [Offset Mode] or
[Adaptive Mode]
.
Offset Mode Sign [+]
[+]
[–]
To offset the voltage by a positive value.
To offset the voltage by a negative value.
ASUS Z97M-PLUS
3-25
3-26
CPU Cache Voltage Offset
Allows you to set the CPU cache voltage offset. By default, this item takes the standard value of the installed CPU. You can use the <+> or <-> keys to adjust the value. The values range from 0.001V to 0.999 V with a 0.001
V interval.
The following item appears only when you set the CPU Cache Voltage to [Adaptive
Mode]
.
Additional Turbo Mode CPU Cache Voltage [Auto]
This item allows you to set the amount of voltage fed to the CPU cores when running in turbo mode. Increase the voltage when configuring a high CPU core frequency. The voltage you set is affected by the offset value. Use the <+> or <-> keys to adjust the value. The values range from 0.001V to 1.920 V with a 0.001 V interval.
Total Adaptive Mode CPU Cache Voltage [Auto]
This item sums up the voltages of the CPU Cache Voltage offset and Additional Turbo
Mode CPU Cache Voltage options.
CPU Graphics Voltage [Auto]
Allows you to configure the voltage amount for the integrated graphics processing unit
(iGPU). Increase the voltage when setting a high iGPU frequency value. Configuration options: [Auto] [Manual Mode] [Offset Mode] [Adaptive Mode]
• The following item appears only when you set the CPU Graphics Voltage to [Manual
Mode]
.
• [Adaptive Mode] is available for some specific CPU types.
CPU Graphics Voltage Override [Auto]
Allows you to set the CPU Graphics Voltage override. By default, this item takes the standard value of the installed CPU. You can use the <+> or <-> keys to adjust the value. The values range from 0.001V to 1.920V with a 0.001V interval.
The following items appear only when you set the CPU Graphics Voltage to [Offset Mode] or [Adaptive Mode].
Offset Mode Sign [+]
[+]
[–]
To offset the voltage by a positive value.
To offset the voltage by a negative value.
CPU Graphics Voltage Offset
By default, this item takes the standard value of the installed CPU. You can use the <+> or <-> keys to adjust the value. The values range from 0.001V to 0.999V with a 0.001V interval.
Chapter 3: BIOS setup
The following item appears only when you set the CPU Graphics Voltage to [Adaptive
Mode]
.
Additional Turbo Mode CPU Graphics Voltage [Auto]
This item allows you to set the amount of voltage fed to the CPU Graphics when running in turbo mode. Increase the voltage when configuring a high CPU core frequency. The voltage you set is affected by the offset value. Use the <+> or <-> keys to adjust the value. The values range from 0.001V to 1.920 V with a 0.001 V interval.
Total Adaptive Mode CPU Cache Voltage [Auto]
This item sums up the voltages of the CPU Cache Voltage offset and Additional Turbo
Mode CPU Cache Voltage options.
CPU System Agent Voltage Offset Mode Sign [+]
[+]
[–]
To offset the voltage by a positive value.
To offset the voltage by a negative value.
CPU System Agent Voltage Offset [Auto]
This item allows you to set the amount of voltage fed to the system agent of the CPU including its PCIE controller and the PCU (power control unit). Increase the voltage to enhance the overclocking capability.
You can use the <+> or <-> keys to adjust the value. The values range from 0.001 V to
0.999 V with a 0.001 V interval.
CPU Analog I/O Voltage Offset Mode Sign [+]
[+]
[–]
To offset the voltage by a positive value.
To offset the voltage by a negative value.
CPU Analog I/O Voltage Offset [Auto]
This item allows you to set the amount of voltage fed to the analog portion of the I/O on the CPU. By default, this item takes the standard value of the installed CPU. Increase the amount of voltage to enhance the overclocking capability.
You can use the <+> or <-> keys to adjust the value. The values range from 0.001 V to
0.999 V with a 0.001 V interval.
CPU Digital I/O Voltage Offset Mode Sign [+]
[+]
[–]
To offset the voltage by a positive value.
To offset the voltage by a negative value.
CPU Digital I/O Voltage Offset [Auto]
This item allows you to set the amount of voltage fed to the digital portion of the I/O on the processor. By default, this item takes the standard value of the installed CPU.
Increase the amount of voltage to enhance the overclocking capability.
You can use the <+> or <-> keys to adjust the value. The values range from 0.001 V to
0.999 V with a 0.001 V interval.
SVID Support [Auto]
Set this item to [Enabled] when overclocking your system. Disabling this item stops the
CPU from communicating with the external voltage regulator. Configuration options: [Auto]
[Disabled] [Enabled]
ASUS Z97M-PLUS
3-27
The following item appears only when you set SVID Support to [Enabled].
SVID Voltage Override [Auto]
This item allows you to set the SVID Voltage override. By default, this item takes the standard value of the installed CPU. You can use the <+> or <-> keys to adjust the value. The values range from 0.001V to 2.440 V with a 0.001 V interval.
DRAM Voltage [Auto]
This item allows you to set the DRAM voltage. You can use the <+> or <-> keys to adjust the value. The values range from 1.1850 V to 1.8000 V with a 0.0050 V interval.
According to Intel
®
CPU specifications, DIMMs with voltage requirement over 1.65 V may damage the CPU permanently. We recommend that you install the DIMMs with the voltage requirement below 1.65 V.
PCH VLX Voltage [Auto]
This item allows you to set the I/O voltage on the PCH (Platform Controller Hub). You can use the <+> or <-> keys to adjust the value. The values range from 1.1850 V to 2.1350 V with a 0.0050 V interval.
PCH Core Voltage [Auto]
This item allows you to set the core voltage on the PCH (Platform Controller Hub). You can use the <+> or <-> keys to adjust the value. The values range from 0.73500V to 1.50000V with a 0.00500V interval.
The system may need better cooling system for a more stable performance under high voltage settings.
DRAM CTRL REF Voltage [Auto]
This item allows you to set the DRAM reference voltage on the control lines from the memory bus. You can use the <+> or <-> keys to adjust the value. The values range from 0.39500x to
0.63000x with a 0.00500x interval.
To set a value for the DRAM reference voltage, we recommend you to set a value close to the standard value which is 0.500000x.
DRAM DATA REF Voltage on CHA/CHB [Auto]
This item allows you to set the DRAM reference voltage on the data lines on Channels A and
B. You can use the <+> or <-> keys to adjust the value. The values range from 0.39500x to
0.63000x with a 0.00500x interval.
To set a value for the DRAM reference voltage, we recommend you to set a value close to the standard value which is 0.500000x.
3-28
CPU Spread Spectrum [Auto]
This item allows you to enhance the BCLK overclocking capability or reduce the EMI
(electromagnetic disturbance) generated by the BCLK. Set this item to [Enabled] for EMI reduction, or set this item to [Disabled] to enhance BCLK overclocking. Configuration options:
[Auto] [Disabled] [Enabled]
Chapter 3: BIOS setup
3.6 Advanced menu
The Advanced menu items allow you to change the settings for the CPU and other system devices.
Be cautious when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction.
ASUS Z97M-PLUS
3-29
3.6.1 CPU Configuration
The items in this menu show the CPU-related information that the BIOS automatically detects.
The items in this menu may vary based on the CPU installed.
3-30
Intel Adaptive Thermal Monitor [Enabled]
This item allows you to protect the CPU by decreasing its frequency as it reaches the thermal throttle point. The thermal monitor includes TM1 (Thermal monitor 1), TM2 (Thermal monitor
2), and EMTTM (Enhanced Multi-threaded Thermal Monitoring). Configuration options:
[Disabled] [Enabled]
Hyper-threading [Enabled]
The Intel Hyper-Threading Technology allows a hyper-threading processor to appear as two logical processors to the operating system, allowing the operating system to schedule two threads or processes simultaneously.
[Enabled]
[Disabled]
Two threads per activated core are enabled.
Only one thread per activated core is enabled.
Active Processor Cores [All]
This item allows you to select the number of CPU cores to activate in each processor package. Configuration options: [All] [1] [2] [3]
For some CPU types, only [All] and [1] appear.
Chapter 3: BIOS setup
Execute Disable Bit [Enabled]
Execute Disable prevents certain classes of malicious buffer overflow attacks when combined with a supporting OS (SuSE Linux 9.2, RedHat Enterprise 3 Update 3). Configuration options:
[Disabled] [Enabled]
Intel Virtualization Technology [Disabled]
When set to [Enabled], a VMM can utilize the additional hardware capabilities provided by
Vanderpool Technology. Configuration options: [Disabled] [Enabled]
Hardware Prefetcher(L2 Cache) [Enabled]
This item allows the CPU to prefetch commands and data in the L2 cache, reduces the
DRAM loading time and improves the system performance. Configuration options: [Disabled]
[Enabled]
Adjacent Cache Line Prefetcher [Enabled]
This item allows the mid level cache (L2) to prefetch adjacent cache lines, reducing the
DRAM loading time and improves the system performance. Configuration options: [Disabled]
[Enabled]
Boot Performance Mode [Max Non-Turbo Performance]
This item allows you to select the CPU performance state during system boot before the operating system takes control. The CPU runs at a selected performance ratio based on CPU configuration. Configuration options: [Max Non-Turbo Performance] [Max Battery] [Turbo
Performance]
Dynamic Storage Accelerator [Disabled]
This item allows you to accelerate the performance of the SSDs (Solid-State Drives) by dynamically adjusting the power management during heavy multitasking. Configuration options: [Enabled] [Disabled]
CPU Power Management Configuration
This item allows you to manage and configure the CPU’s power.
Enhanced Intel SpeedStep Technology [Enabled]
This item allows your system to adjust the CPU’s voltage and cores frequency, resulting in decreased power consumption and heat production.
[Disabled] The CPU runs at its default speed.
[Enabled] The system controls the CPU speed.
Turbo Mode [Enabled]
This item allows you to automatically set the CPU cores to run faster than the base operating frequency when it is below the operating power, current and temperature specification limit. Configuration options: [Enabled] [Disabled]
Turbo Mode is only available on selected CPU models only.
ASUS Z97M-PLUS
3-31
3-32
CPU states [Auto]
This item allows you to set the power saving of the CPU states. Configuration options:
[Auto] [Disabled] [Enabled]
The following items appear only when you set the CPU states to [Enabled].
Enhanced C1 state [Enabled]
This item allows your CPU to reduce power consumption when the system is in idle mode. Configuration options: [Enabled] [Disabled]
CPU C3 Report [Enabled]
This item allows you to disable or enable the CPU C3 report to the operating system. Configuration options: [Enabled] [Disabled]
CPU C6 Report [Enabled]
This item allows you to disable or enable the CPU C6 report to the operating system. Configuration options: [Enabled] [Disabled]
C6 Latency [Short]
This item allows you to set the duration of C6 latency for C6 state.
Configuration options: [Short] [Long]
CPU C7 Report [CPU C7s]
This item allows you to disable or enable the CPU C7 report to the operating system. Configuration options: [Disabled] [CPU C7] [CPU C7s]
C7 Latency [Long]
This item allows you to set the duration of C7 latency for C7 state.
Configuration options: [Short] [Long]
Package C State Support [Auto]
This item allows you to set the a C-state support for the CPU package.
Configuration options: [Auto] [Enabled] [C0/C1] [C2] [C3] [C6] [CPU C7]
[CPU C7s]
Chapter 3: BIOS setup
3.6.2 PCH Configuration
PCI Express Configuration
This item allows you to configure the PCI Express slots.
PCI-E Speed [Auto]
This item allows your system to automatically select the PCI Express port speed. When set to [Gen1], the PCI-E port runs at PCI-E 1.0 speed. When set to [Gen2], the PCI-E port runs at PCI-E 2.0 speed. Configuration options: [Auto] [Gen1] [Gen2]
Intel Rapid Start Technology [Disabled]
This item allows you to enable or disable Intel
®
Rapid Start Technology. Configuration options: [Enabled] [Disabled]
The following items appear only when you set the Intel Rapid Start Technology to
[Enabled]
.
Entry on S3 RTC Wake [Enabled]
The system automatically wakes up and set to Rapid Start Technology S3 mode.
Configuration options: [Enabled] [Disabled
Entry After [0]
This item allows you to set the RTC wake-up timer at S3 entry. The time ranges from 0 minute (immediately) to 120 minutes.
Active Page Threshold Support [Enabled]
The system automatically goes into sleep mode when the partition size is not enough for the Intel
[Disabled]
® Rapid Start Technology to work. Configuration options: [Enabled]
Active Memory Threshold [0]
This item supports Intel Rapid Storage Technology when the partition size is greater than the Active Page Threshold size. When set to zero (0), it will go to Auto mode and checks if the partition size is enough at S3 entry.
Ensure that the caching partition size is larger than the total memory size.
Hybrid Hard Disk Support [Disabled]
This item allows you to enable or disable the hybrid hard disk support for a faster resume time. Configuration options: [Enabled] [Disabled]
ASUS Z97M-PLUS
3-33
Intel Smart Connect Technology
Intel Smart Connect Technology Support [Disabled]
This item allows the system to support Intel Smart Connect Technology, that periodically refreshes selected applications when the system is in sleep mode.
Configuration options: [Enabled] [Disabled]
3.6.3 PCH Storage Configuration
While entering Setup, the BIOS automatically detects the presence of SATA devices. The
SATA Port items show Empty if no SATA device is installed to the corresponding SATA port.
Scroll down to display the other BIOS items.
3-34
SATA(SATA5,6) and M.2 Configuration [Auto]
This item allows you to set an automatic detection between the M.2 devices and SATA devices installed on SATA ports 5 and 6.
[Auto]
[SATA]
[M.2]
The system automatically detects the connected SATA and M.2 devices and set a higher priority to M.2 interface. The connected device will then run at PCIe mode first than SATA mode. The SATA devices are available when no M.2 devices are installed.
The system assigns the priority bandwidth to SATA (SATA5.6) interface with M.2 Socket 3 disabled.
The system assigns the priority bandwidth to M.2 Socket 3 with SATA
(SATA5.6) interface disabled.
Chapter 3: BIOS setup
By default, the system detects the first priority device. The device detection priority is as follows: PCIe M.2 > SATA Mode M.2 > SATA devices.
SATA Mode Selection [AHCI]
This item allows you to set the SATA configuration.
[Disabled]
[IDE]
[AHCI]
Disables the SATA function.
Set to [IDE] when you want to use the Serial ATA hard disk drives as
Parallel ATA physical storage devices.
Set to [AHCI] when you want the SATA hard disk drives to use the AHCI
(Advanced Host Controller Interface). The AHCI allows the onboard storage driver to enable advanced Serial ATA features that increases storage performance on random workloads by allowing the drive to internally optimize the order of commands.
[RAID] Set to [RAID] when you want to create a RAID configuration from the SATA hard disk drives.
The following item appears only when you set the SATA Mode Selection to [RAID].
Pcie Nand Configuration [Auto]
This item allows you to enable or disable PCIe NAND. Configuration options: [Auto]
[Disabled] [Enabled]
Aggressive LPM Support [Disabled]
This item is designed for LPM (link power management) support with a better energy saving conditions. When disabled, the hot plug function of SATA ports are disabled. Configuration options: [Disabled] [Enabled]
S.M.A.R.T. Status Check [On]
S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitoring system that shows a warning message during POST (Power-on Self Test) when an error occurs in the hard disks. Configuration options: [On] [Off]
Hot Plug [Disabled] (SATA6G_1 - SATA6G_6)
These items allow you to enable/disable SATA Hot Plug Support. Configuration options:
[Disabled] [Enabled]
ASUS Z97M-PLUS
3-35
3.6.4 System Agent Configuration
3-36
CPU Display Audio [Enabled]
Enable this item to support CPU display audio output. Configuration options: [Enabled]
[Disabled]
DVI Port Audio [Off]
Enable this item to support audio output for certain DVI monitors. Configuration options: [On]
[Off]
Graphics Configuration
Allows you to select a primary display from CPU, PCIe and PCI graphical devices.
Primary Display [Auto]
This item allows you to select the primary display from CPU, PCIe and PCI devices.
Configuration options: [Auto] [CPU Graphics] [PCIE] [PCI]
CPU Graphics Memory [Auto]
Allows you to set the system memory size allocated to DVMT 5.0 used by the CPU graphics. Configuration options: [Auto] [32M] [64M] [96M] [128M] ~ [448M] [480M]
[512M]
Render Standby [Auto]
This item allows you to enable Intel
®
Graphics Render Standby support to reduce iGPU power use when the system is idle. Configuration options: [Auto] [Disabled] [Enabled]
CPU Graphics Multi-Monitor [Disabled]
This item allows you to empower both integrated and discrete graphics devices for the multi-monitor output. The CPU graphics shared system memory size is fixed at 64 MB.
Configuration options: [Disabled] [Enabled]
DMI Configuration
This item allows you to control various DMI (direct media interface) to run at PCI-E 2.0 speed.
DMI Gen 2 [Enabled]
Set this item to [Enabled] to run DMI at PCI-E 2.0 speed. Configuration options:
[Enabled] [Disabled]
Chapter 3: BIOS setup
NB PCI-E Configuration
This item allows you to configure the NB PCI Express settings.
PCIEx16_1 Link Speed [Auto]
This item allows you to configure the PCIEx16 speed for slot 1. Configuration options:
[Auto] [Gen1] [Gen2] [Gen3]
Memory Configuration
This item allows you to configure the memory configuration parameters.
Memory Scrambler [Enabled]
Set this item to [Enabled] to support high frequency DRAMs for a better stability.
Configuration options: [Enabled] [Disabled]
Memory Remap [Enabled]
Set this item to [Enabled] to support DRAM address remapping for 64-bit operating systems. Configuration options: [Enabled] [Disabled]
3.6.5 USB Configuration
The items in this menu allow you to change the USB-related features.
The Mass Storage Devices item shows the auto-detected values. If no USB device is detected, the item shows None.
Legacy USB Support [Enabled]
[Enabled]
[Disabled]
[Auto]
Your system supports the USB devices in legacy operating systems.
Your USB devices can be used for BIOS setup only and cannot be recognized in the boot devices list.
Your system automatically detects the presence of USB devices at startup.
If any USB devices are detected, the legacy USB support is enabled.
ASUS Z97M-PLUS
3-37
Intel xHCI Mode [Smart Auto]
[Auto]
[Smart Auto]
[Enabled]
[Disabled]
The xHCI is automatically enabled and runs at USB 3.0 mode when the xHCI driver is installed in the operating system.
Upon detection, the xHCI driver supports the USB 3.0 mode during both
POST and operating system.
Enables the xHCI controller.
Disables the xHCI controller.
EHCI Hand-off [Disabled]
[Enabled]
[Disabled]
Enables the support for operating systems without an EHCI hand-off feature.
Disables the EHCI Hand-off support.
Mass Storage Devices [Auto]
This item allows your system to detect the devices according to their media formats.
Configuration options: [Auto] [Floppy] [Forced FDD] [Hard Disk] [CD-ROM]
USB Single Port Control
Allows you to enable or disable the individual USB port.
Refer to section 1.2.2 Motherboard layout for the location of the USB ports.
3.6.6 Platform Misc Configuration
The items in this menu allow you to configure the platform-related features.
3-38
PCI-E Native Power Management [Disabled]
This item allows you to enhance the power saving feature of PCI Express and perform ASPM operations in the operating system. Configuration options: [Disabled] [Enabled]
Chapter 3: BIOS setup
The following item appears only when you set the PCI Express Native Power Management to [Enabled].
Native ASPM [Disabled]
[Enabled]
[Disabled]
Windows ® Vista OS controls the ASPM (active state power management) support for devices.
BIOS controls the ASPM support for the device.
PCH - PCI Express options
DMI Link ASPM Control [Disabled]
This item allows you to control the Active State Power Management on both NB
(NorthBridge) side and SB (SouthBridge) side of the DMI Link. Configuration options:
[Disabled] [Enabled]
ASPM Support [Disabled]
This item allows you to select the ASPM state for energy-saving conditions. Configuration options: [Disabled] [L0s] [L1] [L0sL1] [Auto]
SA - PCI Express options
DMI Link ASPM Control [Disabled]
This item allows you to control the Active State Power Management on both CPU and PCH
(platform controller hub) Both DMI link ASPM control items of the CPU and PCH sides must be enabled for the ASPM to take effect. Configuration options: [Disabled] [L0s] [L1] [L0sL1]
PEG ASPM Support [Disabled]
This item allows you to select the ASPM state for energy-saving conditions, or use the ASUS optimized energy saving profile. Configuration options: [Disabled] [L0s] [L1] [L0sL1] [Auto]
ASUS Z97M-PLUS
3-39
3.6.7 Onboard Devices Configuration
3-40
HD Audio Controller [Enabled]
This item allows you to use the Azalia High Definition Audio Controller. Configuration options:
[Disabled] [Enabled]
The following items appear only when you set the HD Audio Controller to [Enabled].
Front Panel Type [HD Audio]
This item allows you to set the front panel audio connector (AAFP) mode to legacy
AC’97 or high-definition audio depending on the audio standard that the front panel audio module supports.
[HD Audio] Sets the front panel audio connector (AAFP) mode to high definition audio.
[AC97] Sets the front panel audio connector (AAFP) mode to legacy AC’97
SPDIF Out Type [SPDIF]
[SPDIF] Sets to an SPDIF audio output.
[HDMI] Sets to an HDMI audio output.
Depop [Enabled]
Configuration options: [Disabled] [Enabled]
Chapter 3: BIOS setup
Intel LAN Controller [Enabled]
This item allows you to enable or disable the Intel LAN controller. Configuration options:
[Disabled] [Enabled]
The following item appears only when you set the Intel LAN Controller item to [Enabled].
Intel LAN PXE Option ROM [Disabled]
Allows you to enable or disable the PXE OptionRom of the Intel LAN controller. Configuration options: [Enabled] [Disabled]
Charging USB devices in Power State S5 [Disabled]
[Enabled]
[Disabled]
Charges USB devices even when the system is in Power State S5. State
S5 is the soft-off mode or shutdown state where your computer has no memory state and is not doing any computing tasks.
Disables this function.
Serial Port Configuration
The sub-items in this menu allow you to set the serial port configuration.
This item functions only if there is a serial port (COM) connector on the motherboard.
Serial Port [Enabled]
Allows you to enable or disable the serial port (COM). Configuration options: [Enabled]
[Disabled]
Change Settings [IO=3F8h; IRQ=4]
Allows you to select the Serial Port base address. Configuration options: [IO=3F8h;
IRQ=4] [IO=2F8h; IRQ=3] [IO=3E8h; IRQ=4] [IO=2E8h; IRQ=3]
Parallel Port Configuration
The sub-items in this menu allow you to set the parallel port configuration.
Parallel Port [On]
Allows you to enable or disable the parallel port (LPT/LPTE). Configuration options:
[On] [Off]
The following items appear only when you set the Parallel Port item to [On].
Change Settings [Auto]
Allows you to select an optimal setting for Super I/O devices. Configuration options: [Auto] [IO=378h; IRQ=5;] [IO=378h; IRQ=5,6,7,9,10,11,12;] [IO=278h;
IRQ=5,6,7,9,10,11,12;] [IO=3BCh; IRQ=5,6,7,9,10,11,12;]
Device Mode [STD Printe Mode]
Allows you to select the Printer Port mode. Configuration options: [STD Printer Mode]
[SPP Mode] [EPP-1.9 and SPP Mode] [EPP-1.7 and SPP Mode] [ECP Mode] [ECP and EPP 1.9 Mode] [ECP and EPP 1.7 Mode]
ASUS Z97M-PLUS
3-41
3.6.8 APM Configuration
3-42
Deep S4 [Disabled]
When enabled, the system in S4 state will further reduce power usage and will power off the
USB and PS/2 devices. The system in deep S4 state can be woken up via the power button, devices in LAN, or other ways except via the USB and PS/2 devices. Configuration options:
[Disabled] [Enabled]
Restore AC Power Loss [Power Off]
[Power On]
[Power Off]
[Last State]
The system goes into ON state after an AC power loss.
The system goes into OFF state after an AC power loss.
The system goes into either OFF or ON state, whatever the system state was before the AC power loss.
Power On By PS/2 Keyboard [Disabled]
[Disabled]
[Space Bar]
[Ctrl-Esc]
[Power Key]
Disables the Power On by a PS/2 keyboard.
Sets the Space Bar on the PS/2 keyboard to turn on the system.
Sets the Ctrl+Esc key on the PS/2 keyboard to turn on the system.
Sets Power key on the PS/2 keyboard to turn on the system. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead.
Power On By PCIE/PCI [Disabled]
This item allows you to enable or disable the Wake-on-LAN function of the onboard LAN controller or other installed PCIe/PCI LAN cards. Configuration options: [Disabled] [Enabled]
Power On By Ring [Disabled]
[Disabled]
[Enabled]
Disables Ring to generate a wake event.
Enables Ring to generate a wake event.
Power On By RTC [Disabled]
[Disabled]
[Enabled]
Disables RTC to generate a wake event.
When set to [Enabled], the items RTC Alarm Date (Days) and Hour/
Minute/Second
will become user-configurable with set values.
Chapter 3: BIOS setup
3.6.9 Network Stack Configuration
Network stack [Disable]
This item allows you to disable or enable the UEFI network stack. Configuration options:
[Disable] [Enable]
The following item appears only when you set the Network Stack to [Enabled].
Ipv4/Ipv6 PXE Support [Enabled]
This item allows you to enable or disable the Ipv4/Ipv6 PXE wake event. Configuration options: [Disabled] [Enabled]
ASUS Z97M-PLUS
3-43
3.7 Monitor menu
The Monitor menu displays the system temperature/power status, and allows you to change the fan settings.
Scroll down to display the other BIOS items.
3-44
Qfan Tuning
Click this item to automatically detect the lowest speed and configure the minimum duty cycle for each fan.
CPU Temperature / MB Temperature [xxx°C/xxx°F] or [Ignore]
The onboard hardware monitor automatically detects and displays the CPU and motherboard temperatures. Select
[Ignore]
if you do not wish to display the detected temperatures.
CPU Fan Speed [xxxx RPM] or [Ignore] / [N/A], Chassis Fan 1/2 Speed [xxxx
RPM] or [Ignore] / [N/A]
The onboard hardware monitor automatically detects and displays the CPU and chassis fan speed in rotations per minute (RPM). If the fan is not connected to the motherboard, the field shows N/A. Select [Ignore] if you do not wish to display the detected speed.
CPU Input Voltage (VCCIN), CPU Core Voltage, 3.3V Voltage, 5V Voltage, 12V
Voltage
The onboard hardware monitor automatically detects the voltage output through the onboard voltage regulators. Select [Ignore] if you do not want to detect this item.
CPU Q-Fan Control [Auto]
[Auto] Detects the type of CPU fan installed and automatically switch the control modes.
[PWM mode] Enables the CPU Q-Fan control in PWM mode for 4-pin CPU fan.
[DC mode]
[Disabled]
Enables the CPU Q-Fan control in DC mode for 3-pin CPU fan.
Disables the CPU Q-Fan control feature.
Chapter 3: BIOS setup
• The default CPU Q-Fan settings may differ when you set the CPU Q-Fan Control item to [Auto].
• The following items appear only when you set the CPU Q-Fan Control item to [Auto],
[PWM mode] or [DC mode].
CPU Fan Speed Low Limit [200 RPM]
Allows you to set the low limit warning for CPU Fan speed. Configuration options: [Ignore]
[100 RPM] [200 RPM] [300 RPM] [400 RPM] [500 RPM]
CPU Fan Profile [Standard]
Allows you to set the appropriate performance level of the CPU fan.
[Standard] Set to make the CPU fan adjust automatically depending on the CPU temperature.
[Silent]
[Turbo]
[Manual]
Set to minimize the fan speed for quiet CPU fan operation.
Set to achieve maximum CPU fan speed.
Set to assign detailed fan speed control parameters.
The following four items appear only when you set CPU Fan Profile to [Manual].
CPU Upper Temperature [70]
Use the <+> or <-> keys to adjust the upper limit of the CPU temperature.
The values range from 25°C to 75°C.
CPU Fan Max. Duty Cycle(%) [100]
Use the <+> or <-> keys to adjust the maximum CPU fan duty cycle. The values range from 20% to 100%. When the CPU temperature reaches the upper limit, the CPU fan operates at the maximum duty cycle.
CPU Middle Temperature [25]
Use the <+> or <-> keys to set the value for CPU Middle Temperature. The range of the values depends on the CPU installed.
CPU Fan Middle Duty Cycle(%) [20]
Use the <+> or <-> keys to adjust the CPU fan middle duty cycle. The values range from 20% to 100%. When the CPU temperature reaches the upper limit, the CPU fan operates at the maximum duty cycle.
CPU Lower Temperature [20]
Use the <+> or <-> keys to adjust the CPU fan’s lower temperature. The values range from 20% to 75%.
CPU Fan Min. Duty Cycle(%) [20]
Use the <+> or <-> keys to adjust the minimum CPU fan duty cycle. The values range from 20% to 100%. When the CPU temperature is under
40ºC, the CPU fan operates at the minimum duty cycle.
Chassis Fan 1/2 Q-Fan Control [DC Mode]
[PWM mode] Enables the chassis Q-Fan control in PWM mode for 4-pin chassis fan.
[DC mode] Enables the chassis Q-Fan control in DC mode for 3-pin chassis fan.
[Disabled] Disables the chassis Q-Fan control feature.
ASUS Z97M-PLUS
3-45
3-46
The following items appear only when you set the Chassis Fan 1/2 Q-Fan Control item to
[PWM mode] or [DC mode].
Chassis Fan 1/2 Q-Fan Source [CPU]
The assigned fan will be controlled according to the selected temperature source.
Configuration options: [CPU] [MB]
Chassis Fan 1/2 Speed Low Limit [600 RPM]
Allows you to disable or set the chassis fan warning speed. Configuration options: [Ignore]
[200 RPM] [300 RPM] [400 RPM] [500 RPM] [600 RPM]
Chassis Fan 1/2 Profile [Standard]
Allows you to set the appropriate performance level of the chassis fan.
[Standard] Set to make the CPU fan adjust automatically depending on the CPU temperature.
[Silent] Set to minimize the fan speed for quiet CPU fan operation.
[Turbo]
[Manual]
Set to achieve maximum CPU fan speed.
Set to assign detailed fan speed control parameters.
The following four items appear only when you set the Chassis Fan 1/2 Profile item to
[Manual]
.
Chassis Fan 1/2 Upper Temperature [70]
Use the <+> or <-> keys to adjust the upper limit of the CPU temperature.
The values range from 20°C to 75°C.
Chassis Fan 1/2 Max. Duty Cycle(%) [100]
Use the <+> or <-> keys to adjust the maximum chassis fan duty cycle. The values range from 20% to 100%. When the chassis temperature reaches the upper limit, the chassis fan will operate at the maximum duty cycle.
Chassis Fan 1/2 Middle Temperature [45]
Use the <+> or <-> keys to set the value for Chassis Fan Middle
Temperature.
Chassis Fan 1/2 Middle Duty Cycle(%) [60]
Use the <+> or <-> keys to adjust the chassis fan middle duty cycle. The values range from 20% to 100%.
Chassis Fan 1/2 Lower Temperature [40]
Use the <+> or <-> keys to adjust the chassis fans’ lower temperature. The values range from 20% to 75%.
Chassis Fan 1/2 Min. Duty Cycle(%) [60]
Use the <+> or <-> keys to adjust the minimum chassis fan duty cycle. The values range from 20% to 100%. When the chassis temperature is under
40°C, the chassis fan operates at the minimum duty cycle.
Anti Surge Support [Enabled]
This item allows you to enable or disable the Anti Surge function. Configuration options:
[Disabled] [Enabled]
Chapter 3: BIOS setup
3.8 Boot menu
The Boot menu items allow you to change the system boot options.
Scroll down to display the other BIOS items.
Fast Boot [Enabled]
[Disabled]
[Enabled]
This item allows your system to go back to its normal boot speed.
This item allows your system to accelerate the boot speed.
The following items appear only when you set the Fast Boot to [Enabled].
SATA Support [All Devices]
[All Devices] All devices connected to SATA ports are available during POST. This process extends the POST time.
[Hard Drive Only] Only hard drives connected to SATA ports are detected during
POST.
[Boot Drive Only] Only boot drives connected to a SATA ports are detected during
POST.
USB Support [Partial Initialization]
[Disabled] All USB devices will not be available until OS boot up for a fastest
POST time.
[Full Initialization] All USB devices will be available during POST. This process will extend the POST time.
[Partial Initialization] For a faster POST time, only USB ports with keyboard and mouse connections will be detected.
ASUS Z97M-PLUS
3-47
3-48
PS/2 Keyboard and Mouse Support [Auto]
Select any of these settings when PS/2 keyboard and mouse are installed. These settings only apply when Fast Boot is enabled.
[Auto] For a faster POST time, PS/2 devices will only be available when the system boots up or rebooted when the PS/2 devices have not been reconnected or changed. If you disconnect or change PS/2 devices before restarting the system, PS/2 devices will not be available and BIOS setup program will not be accessible via PS/2 devices.
[Full Initialization] For full system control, PS/2 devices will be available during
POST at any circumstances. This process will extend POST time.
[Disabled] For the fastest POST time, all PS/2 devices will not be available until your computer enters the operating system.
Network Stack Driver Support [Disabled]
[Disabled]
[Enabled]
Select to skip the network stack driver from loading during POST.
Select to load the network stack driver during POST.
Next Boot after AC Power Loss [Normal Boot]
[Normal Boot] Returns to normal boot on the next boot after an AC power loss.
[Fast Boot] Accelerates the boot speed on the next boot after an AC power loss.
Boot Logo Display [Auto]
[Auto] Sets the boot logo to display during POST.
[Full Screen] Sets the boot logo display in full screen during POST.
[Disabled] Disables the boot logo display during POST.
The following item appears only when you set the Boot Logo Display to [Auto] and [Full
Screen]
.
Post Delay Time [3 sec]
This item allows you to select a desired additional POST waiting time to easily enter the BIOS Setup. You can only execute the POST delay time during normal boot. The values range from 0 to 10 seconds.
This feature only works when set under normal boot.
The following items appear only when you set the Boot Logo Display to [Disabled].
Post Report [5 sec]
This item allows you to select a desired POST report waiting time.
Configuration options: [1 sec] - [10 sec] [Until Press ESC]
Bootup NumLock State [Enabled]
This item allows you to enable or disable power-on state of the NumLock. Configuration options: [Disabled] [Enabled]
Chapter 3: BIOS setup
Wait For ‘F1’ If Error [Enabled]
This item allows your system to wait for the <F1> key to be pressed when error occurs.
Configuration options: [Disabled] [Enabled]
Option ROM Messages [Enabled]
[Enabled]
[Disabled]
The third-party ROM messages will be displayed during POST.
Disables the ROM messages and displays only the ASUS logo during
POST.
Interrupt 19 Capture [Disabled]
This item allows you to trap Interrupt 19 by the option ROMs. Configuration options:
[Disabled] [Enabled]
Above 4G Decoding [Disabled]
This item allows you to decode the 64-bit capable devices above 4G address space. Ensure that your system supports 64-bit PCI decoding. Configuration options: [Disabled] [Enabled]
Setup Mode [EZ Mode]
[Advanced Mode] Allows you to go to Advanced Mode of the BIOS after POST.
[EZ Mode] Allows you to go to EZ Mode of the BIOS after POST.
CSM (Compatibility Support Module)
Allows you to configure the CSM (Compatibility Support Module) items to fully support the various VGA, bootable devices and add-on devices for better compatibility.
Launch CSM [Enabled]
[Auto]
[Enabled]
[Disabled]
The system automatically detects the bootable devices and the addon devices.
For better compatibility, enable the CSM to fully support the non-UEFI driver add-on devices or the Windows
®
UEFI mode.
Disable the CSM to fully support the Windows ®
Security Boot.
Security Update and
The following four items appear when you set Launch CSM to [Enabled].
Boot Device Control [UEFI and Legacy OPROM]
Allows you to select the type of devices that you want to boot. Configuration options: [UEFI and Legacy OPROM] [Legacy OPROM only] [UEFI only]
Boot from Network Devices [Legacy OPROM first]
Allows you to select the type of network devices that you want to launch.
Configuration options: [Legacy OPROM first] [UEFI driver first] [Ignore]
Boot from Storage Devices [Legacy OPROM first]
Allows you to select the type of storage devices that you want to launch.
Configuration options: [Both, Legacy OPROM first] [Both, UEFI first]
[Legacy OPROM first] [UEFI driver first] [Ignore]
Boot from PCI-E/PCI Expansion Devices [Legacy OPROM first]
Allows you to select the type of PCIe/PCI expansion devices that you want to launch. Configuration options: [Legacy OPROM first] [UEFI driver first]
ASUS Z97M-PLUS
3-49
3-50
Secure Boot
Allows you to configure the Windows Secure Boot settings and manage its keys to protect the system from unauthorized access and malwares during POST.
OS Type [Windows UEFI mode]
[Windows UEFI
Mode]
Allows you to select your installed operating system. Execute the Microsoft ® Secure Boot check. Only select this option when booting on Windows
®
UEFI mode or other Microsoft
®
Secure
Boot compliant OS.
[Other OS]
Get the optimized function when booting on Windows
®
non-
UEFI mode and Microsoft ® Secure Boot non-compliant OS.
Microsoft
®
Secure Boot only supports Windows
®
UEFI mode.
Key Management
This item allows you to manage the Secure Boot keys.
Install Default Secure Boot keys
This item allows you to immediately load the default Security Boot keys,
Platform key (PK), Key-exchange Key (KEK), Signature database (db), and
Revoked Signatures (dbx). When the default Secure boot keys are loaded, the PK state will change from Unloaded mode to loaded mode.
Clear Secure Boot keys
This item appears only when you load the default Secure Boot keys. This item allows you to clear all default Secure Boot keys.
Save Secure Boot Keys
This item allows you to save the PK (Platform Keys) to a USB storage device.
PK Management
The Platform Key (PK) locks and secures the firmware from any permissible changes.
The system verifies the PK before your system enters the OS.
Delete PK
Allows you to delete the PK from your system. Once the PK is deleted, all the system’s Secure Boot keys will not be active.
Load Default PK
Select Yes to load the system default PK or select No to load a downloaded
PK from a USB storage device.
The PK file must be formatted as a UEFI variable structure with time-based authenticated variable.
KEK Management
The KEK (Key-exchange Key or Key Enrollment Key) manages the Signature database
(db) and Revoked Signature database (dbx).
Key-exchange Key (KEK) refers to Microsoft ® Secure Boot Key-Enrollment Key (KEK).
Chapter 3: BIOS setup
Delete KEK
Allows you to delete the KEK from your system. Once the KEK is deleted, the db and the dbx cannot be updated in the operating system.
Load Default KEK
Select Yes to load the system default KEK or select No to load a downloaded KEK from a USB storage device.
Append Default KEK
Select Yes to append the system default KEK or select No to append a downloaded additional KEK from a USB storage device for the db and dbx management.
The KEK file must be formatted as a UEFI variable structure with time-based authenticated variable.
DB Management
The db (Authorized Signature database) lists the signers or images of UEFI applications, operating system loaders, and UEFI drivers that you can load on the single computer.
Delete the db
Allows you to delete the db file from your system. Doing so may cause boot failures.
Load Default db
Select Yes to load the system default db or select No to load a downloaded db from a USB storage device.
Append Default db
Select Yes to append the system default db or select No to append a downloaded additional db from a USB storage device to load certain customized UEFI executable files.
• The db file must be formatted as a UEFI variable structure with time-based authenticated variable.
• UEFI executable files include UEFI boot devices, drivers and applications.
dbx Management
The dbx (Revoked Signature database) lists the forbidden images of db items that are no longer trusted and cannot be loaded.
Delete the dbx
Allows you to delete the DBX file from your system. Doing so may expose the system to security threats.
Load Default dbx
Select Yes to load the system default dbx or select No to load a downloaded dbx from a USB storage device.
ASUS Z97M-PLUS
3-51
Append Default dbx
Select Yes to append the system default dbx or select No to append a downloaded additional dbx from a USB storage device to forbid certain customized UEFI executable files.
The dbx file must be formatted as a UEFI variable structure with time-based authenticated variable.
Boot Option Priorities
These items specify the boot device priority sequence from the available devices. The number of device items that appears on the screen depends on the number of devices installed in the system.
• To access Windows
® supported).
OS in Safe Mode, press <F8 > after POST (Windows
®
8 not
• To select the boot device during system startup, press <F8> when ASUS Logo appears.
Boot Override
These items displays the available devices. The number of device items that appears on the screen depends on the number of devices installed in the system. Click an item to start booting from the selected device.
3-52 Chapter 3: BIOS setup
3.9 Tool menu
The Tool menu items allow you to configure options for special functions. Select an item then press <Enter> to display the submenu.
3.9.1 ASUS EZ Flash 2 Utility
This item allows you to run ASUS EZ Flash 2. When you press <Enter>, a confirmation message appears. Use the left/right arrow key to select between [Yes] or [No], then press
<Enter> to confirm your choice.
For more details, refer to section 3.11.2 ASUS EZ Flash 2.
Setup Animator [Enabled]
This item allows you to enable or disable the Setup animator. Configuration options:
[Disabled] [Enabled]
ASUS Z97M-PLUS
3-53
3.9.2 ASUS Overclocking Profile
This item allows you to store or load multiple BIOS settings.
3-54
Load from Profile
This item allows you to load the previous BIOS settings saved in the BIOS Flash. Key in the profile number that saved your BIOS settings, press <Enter>, and then select Yes.
• DO NOT shut down or reset the system while updating the BIOS to prevent the system boot failure!
• We recommend that you update the BIOS file only coming from the same memory/
CPU configuration and BIOS version.
Profile Name
This item allows you to key in a profile name.
Save to Profile
This item allows you to save the current BIOS settings to the BIOS Flash, and create a profile. Key in a profile number from one to eight, press <Enter>, and then select Yes.
Load/Save Profile from/to USB Drive
This item allows you to load or save profile from your USB drive, load and save profile to your
USB drive.
Chapter 3: BIOS setup
3.9.3 ASUS SPD Information
This item allows you to view the DRAM SPD information.
ASUS Z97M-PLUS
3-55
3.10 Exit menu
The Exit menu items allow you to load the optimal default values for the BIOS items, and save or discard your changes to the BIOS items.
3-56
Load Optimized Defaults
This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press <F5>, a confirmation window appears.
Select OK to load the default values.
Save Changes & Reset
Once you are finished making your selections, choose this option from the Exit menu to ensure the values you selected are saved. When you select this option or if you press <F10>, a confirmation window appears. Select OK to save changes and exit.
Discard Changes & Exit
This option allows you to exit the Setup program without saving your changes. When you select this option or if you press <Esc>, a confirmation window appears. Select OK to discard changes and exit.
Launch EFI Shell from USB drives
This option allows you to attempt to launch the EFI Shell application (shellx64.efi) from one of the available USB devices.
Chapter 3: BIOS setup
3.11 Updating BIOS
The ASUS website publishes the latest BIOS versions to provide enhancements on system stability, compatibility, or performance. However, BIOS updating is potentially risky. If there is no problem using the current version of BIOS, DO NOT manually update the BIOS.
Inappropriate BIOS updating may result in the system’s failure to boot. Carefully follow the instructions of this chapter to update your BIOS if necessary.
Visit the ASUS website at www.asus.com to download the latest BIOS file for this motherboard.
The following utilities allow you to manage and update the motherboard BIOS setup program.
1. EZ Update: Updates the BIOS in Windows ® environment.
For details, refer to section 4.4.6 EZ Update.
2. ASUS EZ Flash 2: Updates the BIOS using a USB flash drive.
3. ASUS CrashFree BIOS 3: Restores the BIOS using the motherboard support DVD or a
USB flash drive when the BIOS file fails or gets corrupted.
4. ASUS BIOS Updater: Updates the BIOS in DOS environment using the motherboard support DVD and a USB flash disk drive.
Save a copy of the original motherboard BIOS file to a USB flash disk in case you need to restore the BIOS in the future. Copy the original motherboard BIOS using the ASUS Update or BIOS Updater utilities.
3.11.1 EZ Update
The EZ Update is a utility that allows you to update the motherboard BIOS in Windows
® environment.
• EZ Update requires an Internet connection either through a network or an ISP
(Internet Service Provider).
• This utility is available in the support DVD that comes with the motherboard package.
• Refer to section 4.4.6 EZ Update of this user guide for more information.
ASUS Z97M-PLUS
3-57
3.11.2 ASUS EZ Flash 2
ASUS EZ Flash 2 allows you to update the BIOS without having to use a bootable floppy disk or an OS-based utility.
Before you start using this utility, download the latest BIOS from the ASUS website at www.asus.com.
To update the BIOS using EZ Flash 2:
1. Insert the USB flash disk that contains the latest BIOS file to the USB port.
2. Enter the Advanced Mode of the BIOS setup program. Go to the Tool menu to select
ASUS EZ Flash Utility and press <Enter> to enable it.
3-58
3. Press the Left/Right arrow keys to switch to the Drive field.
4. Press the Up/Down arrow keys to find the USB flash disk that contains the latest BIOS, and then press <Enter>.
5. Press the Left/Right arrow keys to switch to the Folder Info field.
6. Press the Up/Down arrow keys to find the BIOS file, and then press <Enter> to perform the BIOS update process. Reboot the system when the update process is done.
Chapter 3: BIOS setup
• This function can support devices such as a USB flash disk with FAT 32/16 format and single partition only.
• DO NOT shut down or reset the system while updating the BIOS to prevent system boot failure!
Ensure to load the BIOS default settings to ensure system compatibility and stability. Select the Load Optimized Defaults item under the Exit menu. See section 3.10 Exit Menu for details.
3.11.3 ASUS CrashFree BIOS 3
The ASUS CrashFree BIOS 3 utility is an auto recovery tool that allows you to restore the
BIOS file when it fails or gets corrupted during the updating process. You can restore a corrupted BIOS file using the motherboard support DVD or a USB flash drive that contains the BIOS file.
• The BIOS file in the support DVD may not be the latest version. Download the latest
BIOS file from the ASUS website at www.asus.com.
• Before using this utility, rename the BIOS file in the removable device into
Z97MPLUS.CAP
.
Recovering the BIOS
To recover the BIOS:
1. Turn on the system.
2. Insert the motherboard support DVD to the optical drive, or the USB flash drive containing the BIOS file to the USB port.
3. The utility automatically checks the devices for the BIOS file. When found, the utility reads the BIOS file and enters ASUS EZ Flash 2 automatically.
4. The system requires you to enter BIOS Setup to recover the BIOS setting. To ensure system compatibility and stability, we recommend that you press <F5> to load default
BIOS values.
DO NOT shut down or reset the system while updating the BIOS! Doing so can cause system boot failure!
ASUS Z97M-PLUS
3-59
3-60
3.11.4 ASUS BIOS Updater
ASUS BIOS Updater allows you to update the BIOS in DOS environment.
The screen captures used in this section are for reference only and may not be exactly the same as actually shown on your computer screen.
•
•
Before updating BIOS
•
•
Prepare the motherboard support DVD and a USB flash drive.
Download the latest BIOS file and BIOS Updater from http://support.asus.com and save them in your USB flash drive.
NTFS is not supported under FreeDOS environment. Ensure that your USB flash drive is in single partition and in FAT32/16 format.
Turn off the computer.
Ensure that your computer has a DVD optical drive.
Booting the system in DOS environment
To boot the system in DOS:
1. Insert the USB flash drive with the latest BIOS file and BIOS Updater to the USB port.
2. Boot your computer then press <F8> to launch the select boot device screen.
3. When the select boot device screen appears, insert the Support DVD into the optical drive then select the optical drive as the boot device.
Please select boot device:
and to move selection
ENTER to select boot device
ESC to boot using defaults
P2: ST3808110AS (76319MB) aigo miniking (250MB)
UEFI: (FAT) ASUS DRW-2014L1T(4458MB)
P1: ASUS DRW-2014L1T(4458MB)
UEFI: (FAT) aigo miniking (250MB)
Enter Setup
Chapter 3: BIOS setup
4. When the booting message appears, press <Enter> within five (5) seconds to enter
FreeDOS prompt.
ISOLINUX 3.20 2006-08-26 Copyright (C) 1994-2005 H. Peter Anvin
A Bootable DVD/CD is detected. Press ENTER to boot from the DVD/CD.
If no key is pressed within 5 seconds, the system will boot next priority device automatically. boot:
5. On the FreeDOS prompt, type d: then press <Enter> to switch the disk from Drive C
(optical drive) to Drive D (USB flash drive).
Welcome to FreeDOS (http://www.freedos.org)!
C:/> d:
D:/>
Updating the BIOS file
To update the BIOS file:
1. On the FreeDOS prompt, type bupdater /pc /g and press <Enter>.
D:/> bupdater /pc /g
2. On the BIOS Updater screen, press <Tab> to switch from Files panel to Drives panel then select D:.
BOARD:
VER:
DATE:
ASUSTeK BIOS Updater for DOS V1.30 [2014/01/01]
Current ROM
Z97M-PLUS
0313
PATH: C:\
(H :00 B :00)
03/18/2014
Update ROM
BOARD: Unknown
VER: Unknown
DATE: Unknown
C:
D:
FORMAN~1 <DIR>
Z97MPLUS.CAP 8390656 2014-03-18 21:14:34
Drives panel
Files panel
Note
[Enter] Select or Load [Tab] Switch [V] Drive Info
[Up/Down/Home/End] Move [Esc] Exit
3. Press <Tab> to switch from Drives panel to Files panel then press <Up/Down or Home/
End> keys to select the BIOS file and press <Enter>.
ASUS Z97M-PLUS
3-61
4. After the BIOS Updater checks the selected BIOS file, select Yes to confirm the BIOS update.
Are you sure you want to update the BIOS?
Yes No
The BIOS Backup feature is not supported due to security regulations.
5. Select Yes then press <Enter>. When BIOS update is done, press <ESC> to exit BIOS
Updater.
6. Restart your computer.
DO NOT shut down or reset the system while updating the BIOS to prevent system boot failaure.
Ensure to load the BIOS default settings to ensure system compatibility and stability. Select the Load Optimized Defaults item under the Exit BIOS menu. See Chapter 3 of your motherboard user guide for details.
3-62 Chapter 3: BIOS setup
Chapter 4: Software support
Software support
4.1 Installing an operating system
4
• This motherboard supports 32-bit/64-bit Windows
®
7, 32-bit/64-bit Windows
®
8, and
32-bit/64-bit Windows ® 8.1 operating systems (OS).
• Motherboard settings and hardware options vary. The setup procedures presented in this chapter are for reference only. Refer to Windows
®
operating system documentation for detailed information.
4.2 Support DVD information
The contents of the support DVD are subject to change at any time without notice. Visit the
ASUS website at www.asus.com for updates.
4.2.1 Running the support DVD
Ensure that you have an Administrator account before running the support DVD in
Windows
®
7, Windows
®
8, or Windows
®
8.1 operating systems.
To run the support DVD:
1. Place the Support DVD into the optical drive.
2. In the AutoPlay dialog box, click or tap Run ASSETUP.EXE.
If the AutoPlay dialog box does not appear, browse the contents of the support DVD and double-click or tap \\bin\ASSETUP.EXE to launch the ASUS motherboard support DVD main menu.
ASUS Z97M-PLUS
4-1
Support DVD main menu
The Drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to use the devices.
The AHCI/RAID Driver menu contains the
RAID/AHCI driver disk.
The Utilities menu shows the applications and other software that the motherboard supports.
Click or tap an item to install
The Manual menu contains the list of supplementary user guides. Click or tap an item to open the folder of the user guide.
Click or tap to display the
ASUS contact information.
The Specials tab contains the unique features of ASUS motherboard
Click or tap an icon to display
DVD/motherboard information
4.2.2 Obtaining the software manuals
The software manuals are included in the support DVD. Follow the instructions below to get the necessary software manuals.
The software manual files are in Portable Document Format (PDF). Install the Adobe
Acrobat
®
Reader from the Utilities tab before opening the files.
®
To read about your motherboard’s utility guide:
1. Click Manual tab > ASUS Motherboard
Utility Guide
.
4-2 Chapter 4: Software support
2. From the Manual folder, open the folder of the software manual that you wish to read.
3. Some software manuals are provided in different languages. Open the language’s folder to view the software manual.
The screenshots in this section are for reference only. The actual software manuals containing in the support DVD vary by models.
4.3 Software information
Most of the applications in the support DVD have wizards that will conveniently guide you through the installation. View the online help or readme file that came with the software application for more information.
4.4 AI Suite 3
AI Suite 3 is an all-in-one interface that integrates several ASUS utilities and allows you to launch and operate these utilities simultaneously.
Installing AI Suite 3
Ensure that you have an Administrator account before installing AI Suite 3 in Windows
®
7,
Windows
®
8, or Windows
®
8.1 operating systems.
ASUS Z97M-PLUS
4-3
To install AI Suite 3 on your computer:
Windows
®
7 OS
1. Place the Support DVD into the optical drive.
2. In the AutoPlay dialog box, click or tap Run ASSETUP.exe then select the Utilities tab.
The main screen of the AI Suite 3 is for reference only and vary with models.
4-4
3. From the Utilities tab, click or tap AI Suite 3 then follow the succeeding onscreen instructions.
Windows
®
8 and Windows
®
8.1 OS
1. Place the Support DVD into the optical drive then follow onscreen instructions.
2. From the ASUS motherboard support DVD main menu, select the Utilities tab and click or tap AI Suite 3.
3. Follow the succeeding onscreen instructions.
If the ASUS motherboard support DVD main menu did not appear, try the following: a. Go to the Start Screen then click or tap the Desktop app. b. On the lower left corner of the Desktop, click or tap File Explorer then select your DVD drive and tap or double-click or tap the Setup application.
Chapter 4: Software support
Launching AI Suite 3
Windows
®
7 OS
From the Desktop, click or tap Start > All Programs > ASUS > AI Suite 3 > AI Suite 3.
You can also launch AI Suite in Windows ® area.
7 by clicking or tapping on the Notification
Windows
®
8 and Windows
®
8.1 OS
To launch AI Suite 3 in Windows
®
8 or Windows
®
8.1, tap the AI Suite 3 app on the Start Screen (or if you’re using a mouse, click or tap the AI
Suite 3 app on the Start Screen).
AI Suite 3 Main menu
The AI Suite 3 main menu gives you easy-access controls and insight to what’s going on with your computer - allowing you to optimize performance settings while at the same time ensuring system stability.
The AI Suite main menu includes is a quick-access menu bar that allows you to swiftly launch any of the integrated ASUS utilities. Click or tap on the top-right corner of the menu to launch the menu bar.
Click or tap to launch AI
Suite 3 menu bar
The Ai Suite 3 screenshots in this section are for reference only and can vary depending on motherboard model.
ASUS Z97M-PLUS
4-5
AI Suite 3 main menu bar
DIGI+VRM
TurboV EVO USB 3.0 Boost System Information
EPU Fan Xpert 3 EZ Update Push Notice Version
• The screenshots of AI Suite 3 in this user manual are for reference only. The actual screenshots vary with models.
• Refer to the software manual in the support DVD or visit the ASUS website at www.asus.com for detailed software configuration.
4.4.1 DIGI+ VRM
ASUS DIGI+ VRM allows you to adjust VRM voltage and frequency modulation to enhance reliability and stability. It also provides the highest power efficiency, generating less heat to longer component lifespan and minimize power loss.
Launching DIGI+ VRM
To launch DIGI+ VRM, click or tap then select DIGI+ VRM.
on the top-right corner of the AI Suite 3 main menu,
1
2
3
4
5
Help
Click to undo all the changes
Click to apply all the changes
4-6
1
2
CPU Power Phase Control
Increase phase number under heavy system loading to get more transient and better thermal performance. Reduce phase number under light system loading to increase VRM efficiency.
CPU VRM Switching Frequency
Changing frequency affects the transient response and component thermal conditions. Higher frequency gets quicker transient response.
Chapter 4: Software support
3
4
5
CPU Current Capability
CPU Current Capability provides wider total power range for overclocking. A higher value brings a wider total power range and extends the overclocking frequency range simultaneously.
CPU Load-line Calibration
It allows you to adjust the voltage range to control the CPU Load-line. Adjust to a high value for system performance or to a low value for power efficiency.
CPU Power Duty Control
CPU Power Duty Control adjusts the current of every VRM phase and the thermal of every phase component.
• The actual performance boost may vary depending on your CPU specification.
• Do not remove the thermal module. The thermal conditions should be monitored.
Visit the ASUS website at www.asus.com for detailed software configuration.
4.4.2 EPU
EPU is an enery-saving utility that allows you to adjust the CPU, GPU, and Fan Control settings to their power-saving conditions.
Launching EPU
To launch EPU, click or tap select EPU.
on the top-right corner of the AI Suite 3 main menu, then
Click to configure the settings in Auto mode
Click to configure the settings in
Performance mode
Click to configure the settings in Power
Saving mode
Click to configure the settings in
Away mode
Enables or disables
Configured Max CPU
Power
Tick to select a setting for Voltage
Decrement
Click or to adjust the
Configured Max
CPU Power
Click to select a fan profile
Tick to put the system sound on mute mode
ASUS Z97M-PLUS
4-7
4-8
• When you enable Configured Max CPU Power for advanced energy saving condition, the CPU frequency may display 800 MHz in the Windows
®
OS information of your computer. However, the true CPU frequency varies depending on the wattage that you manually set. You can adjust the CPU wattage from the lowest base to your preferred default value.
• Configured Max CPU Power may decrease the total power delivery to the CPU and affects the CPU performance under system heavy load. To restore your system to its default settings, reboot your computer.
4.4.3 TurboV EVO
ASUS TurboV EVO allows you to manually adjust the CPU frequency, CPU Cache and Core frequencies, and related voltages for an enhanced system stability and boost performance.
It also provides the Auto Tuning function that offers automatic and easy overclocking and system level up.
Launching TurboV EVO
To launch TurboV EVO, click or tap menu, then select TurboV EVO.
on the top-right corner of the AI Suite 3 main
Visit the ASUS website at www.asus.com for detailed software configuration.
Refer to the CPU documentation before adjusting CPU voltage settings. Setting a high voltage may damage the CPU permanently, and setting a low voltage may make the system unstable.
For system stability, all changes made in TurboV EVO will not be saved to BIOS settings and will not be kept on the next system boot. Use the Save Profile function to save your customized overclocking settings and manually load the profile after Windows starts.
Using TurboV EVO
CPU Frequency
Click or to adjust the BCLK Frequency
Click or to adjust the CPU Cache Ratio
Click or to adjust DRAM,
CPU Analog I/O,
PCH Core, and
PCHVLX voltages
Click to save the changes into a profile
Click to load the saved profile
Click to reset to default settings
Drag to adjust CPU
Core Voltage offset
Drag to adjust CPU
Cache Voltage offset
Click or to adjust
CPU System Agent, CPU
Digital I/O, and CPU
Input (VCCIN) voltages
Click to undo all the changes
Click to apply all the changes
Chapter 4: Software support
GPU Boost
Click to save the changes into a profile
Click to load the saved profile
Auto Tuning
Click or to adjust the iGPU Max Ratio
Click to reset to default settings
Click to undo all the changes
Tick Adaptive or Manual to select the CPU
Graphics Voltage mode
Drag to adjust CPU
Graphics Voltage settings
Click to apply all the changes
Select the function to auto-tune
Click to automatically overclock and achieve a total system level up.
Click to reset to default settings
4.4.4 Fan Xpert 3
Fan Xpert 3 automatically detects and tweaks the fan speeds, and provides you with optimized fan settings based on the fans’ specifications and positions.
Launching Fan Xpert 3
To launch Fan Xpert 3, click or tap menu, then select Fan Xpert 3.
on the top-right corner of the AI Suite 3 main
Click to set the fan’s speed to silent mode
Click to set the balanced configuration between the fan’s noise level and speed
Click to increase the fan’s speed for a high cooling capability
Click a screen to select the type of fan that you want to customize
Click to switch between CPU and chassis fan screens
Click to maximize the fan speed
ASUS Z97M-PLUS
4-9
Customizing the fan settings
Smart Mode
Smart Mode allows you to customize the fans’ rotation speeds and responsiveness based on your system’s temperature.
Click and drag to set the fan’s rotation speed
Click and drag the sliders to adjust the fan’s responsiveness
Click to undo the changes
Click to go back to the previous screen
Click to switch between the CPU and chassis fan screens
Click to apply the changes
Fixed RPM Mode
RPM Mode allows you to set the fan speed when the CPU temperature is below 75 o C.
Click and drag to adjust the fan’s speed
4-10
Click to go back to the previous screen
Click to switch between the
CPU and chassis fan screens
• When the CPU temperature reaches 75 o to protect the CPU.
C, the fan will automatically run at full speed
• The Fan Xpert 3 may not be able to detect the fan speed if your fan is installed with an external control kit for rotation speed.
• Fan Xpert 3 does not support 2-pin fans. If you install a 2-pin fan, it can only run at its full speed.
• If the CPU or chassis fans have been changed, the Fan Auto Tuning process should be repeated.
DO NOT remove your fan during the Fan Auto Tuning process.
Chapter 4: Software support
4.4.5 USB 3.0 Boost
USB 3.0 Boost technology supports UASP (USB Attached SCSI Protocol) that automatically speeds up the transfer rates of your USB storage devices.
Launching USB 3.0 Boost
To launch USB 3.0 Boost, click or tap menu, then select USB 3.0 Boost.
on the top-right corner of the AI Suite 3 main
Using USB 3.0 Boost
1. Connect a USB 3.0 device to the USB 3.0 port.
2. From the USB 3.0 Boost screen, click to select a USB device.
3. To enable UASP on your USB device, click UASP. To revert to its normal transfer rate, click Normal.
Click to select a USB device
Click to enable the USB device’s normal data transfer rate
Click to enable UASP or
Turbo Mode to the USB device for a faster data transfer rate
• Visit the ASUS website at www.asus.com for detailed software configuration.
• Use the USB 3.0 devices for high performance. The data transfer speed varies with
USB devices.
ASUS Z97M-PLUS
4-11
4.4.6 EZ Update
EZ Update is a utility that allows you to automatically update your motherboard’s softwares, drivers and the BIOS version easily. With this utlity, you can also manually update the saved
BIOS and select a boot logo when the system goes into POST.
Launching EZ Update
To launch EZ Update, click or tap then select EZ Update.
on the top-right corner of the AI Suite 3 main menu,
Click to automatically update your motherboard’s driver, software and firmware
Click to find and select the BIOS from file
Click to select a boot logo
Click to update the BIOS
Manually update the BIOS and selecting a boot logo
Click or tap to search an image file for your boot logo
4-12
Click or tap to go back to
EZ Update main screen
Click or tap to proceed the updating
BIOS and boot logo
After you click or tap BIOS Update button, click or tap Flash to update the BIOS and upload the boot logo in your system.
Chapter 4: Software support
4.4.7 Push Notice
This utility allows you get the detailed status of your system to your smart device. You can also send messages to your smart device using this utility.
Before using this utility, ensure that you pair your computer with your smart device. For pairing information, refer to section Pairing your computer and smart device.
Launching Push Notice on your computer
To launch Push Notice, click or tap menu, then select Push Notice.
on the top-right corner of the AI Suite 3 main
Push Notice screen
Click or tap to enable Push Notice
Tick to select the smart device
Click or tap to discard the settings
Click or tap to apply the settings
You can also enable the Push Notice via the Push Notice shortcut on the lower-right corner of your screen. To do this, click or tap << then click or tap then select .
Pairing your computer and smart device
To pair your computer and smart device:
1. On your smart device, tap to launch Push Notice.
Push Notice
2. Tap Push Scan then tap the name of your computer that you want to pair with.
To pair your computer and smart device, ensure that both are connected to the same wireless network.
ASUS Z97M-PLUS
4-13
Setting up PC Mode alerts of your computer
This feature allows you to restart, shut down, or put your computer to sleep mode and sends an alert to your smart device.
Tick these to enable mode alerts
Set the day and time to enable the PC modes
Set the minutes to send the alert before the PC mode/s activatation
Key in your messages for more information
Tick to select the smart device
Setting up PC Status alerts
This feature allows you to send alerts of the unusual activities of the voltage, temperature, and fan settings of your computer to your smart device.
Tick to select the smart device
Tick to select and send alerts to your smart device
Tick to send alert when the components selected are back to its normal status
4-14 Chapter 4: Software support
Sending messages to your smart device
This feature allows you to send messages to your smart device.
You can also send messages via the Push Notice messaging shortcut on the lower-right corner of your screen. To do this, click or tap << then click or tap then select .
Tick to select the smart device
Click or tap to send your message
Click or tap to key in your message
Viewing your computer status on your smart device
Tap
Push Notice
on your smart device to launch Push Notice.
Tap to view PC mode alerts
Tap to view PC status alerts
Tap to view PC sent messages
Tap to scan more host computers
Tap to delete PC alerts
ASUS Z97M-PLUS
4-15
4-16
4.4.8 System Information
This utility allows you get the detailed information of the motherboard, CPU, and memory settings.
Launching System Information
To launch System Information, click or tap main menu, then select System Information.
Viewing the motherboard information
From the System Information screen, click MB tab to view the motherboard’s information.
on the top-right corner of the AI Suite 3
Viewing the CPU information
From the System Information screen, click CPU tab to view the processor’s information.
Viewing the SPD information
From the System Information screen, click SPD tab to view the memory’s information.
Chapter 4: Software support
4.4.9 Version
This utility displays the version information of the utilities integrated in AI Suite 3.
Launching Version
To launch Version, click or tap then select Version.
on the top-right corner of the AI Suite 3 main menu,
ASUS Z97M-PLUS
4-17
4-18
4.5 Audio configurations
The Realtek ® audio CODEC provides 7.1-channel audio capability to deliver the ultimate audio experience on your computer. The software provides Jack-Sensing function, S/PDIF
Out support, and interrupt capability. The CODEC also includes the Realtek
®
proprietary
UAJ ® (Universal Audio Jack) technology for all audio ports, eliminating cable connection errors, and giving users plug and play convenience.
Follow the installation wizard to install the Realtek ® came with the motherboard package.
Audio Driver from the support DVD that
If the Realtek ® audio software is correctly installed, you will find the
Realtek
®
HD Audio Manager icon on the taskbar. Double-click on the icon to display the Realtek ® HD Audio Manager.
Configuration option tabs (vary with the audio devices connected)
Realtek
®
HD Audio Manager
Realtek
®
HD Audio Manager for Windows
®
8.1 / Windows
®
8 / Windows
®
7
Advanced settings
Set default device button
Control settings panel
Analog and digital connector status
Chapter 4: Software support
Chapter 5: RAID support
RAID support
5
5.1 RAID configurations
The motherboard supports the following SATA RAID solutions:
• Intel
®
Rapid Storage Technology with RAID 0, RAID 1, RAID 10 and RAID 5 support.
If you want to install a Windows
®
operating system to a hard disk drive included in a RAID set, you have to create a RAID driver disk and load the RAID driver during OS installation.
Refer to section 5.2 Creating a RAID driver disk for details.
5.1.1 RAID definitions
RAID 0 (Data striping)
optimizes two identical hard disk drives to read and write data in parallel, interleaved stacks. Two hard disks perform the same work as a single drive but at a sustained data transfer rate, double that of a single disk alone, thus improving data access and storage. Use of two new identical hard disk drives is required for this setup.
RAID 1 (Data mirroring)
copies and maintains an identical image of data from one drive to a second drive. If one drive fails, the disk array management software directs all applications to the surviving drive as it contains a complete copy of the data in the other drive. This RAID configuration provides data protection and increases fault tolerance to the entire system. Use two new drives or use an existing drive and a new drive for this setup. The new drive must be of the same size or larger than the existing drive.
RAID 5
stripes both data and parity information across three or more hard disk drives. Among the advantages of RAID 5 configuration include better HDD performance, fault tolerance, and higher storage capacity. The RAID 5 configuration is best suited for transaction processing, relational database applications, enterprise resource planning, and other business systems.
Use a minimum of three identical hard disk drives for this setup.
RAID 10
is data striping and data mirroring combined without parity (redundancy data) having to be calculated and written. With the RAID 10 configuration you get all the benefits of both
RAID 0 and RAID 1 configurations. Use four new hard disk drives or use an existing drive and three new drives for this setup.
ASUS Z97M-PLUS
5-1
5.1.2 Installing Serial ATA hard disks
The motherboard supports Serial ATA hard disk drives. For optimal performance, install identical drives of the same model and capacity when creating a disk array.
To install the SATA hard disks for a RAID configuration:
1. Install the SATA hard disks into the drive bays.
2. Connect the SATA signal cables.
3. Connect a SATA power cable to the power connector on each drive.
5.1.3 Setting the RAID item in BIOS
You must enable the RAID function in the BIOS Setup before creating RAID sets using SATA
HDDs. To do this:
1. Enter the BIOS Setup during POST.
2. Go to the Advanced menu > PCH Storage Configuration, and then press <Enter>.
3. Set the SATA Mode Selection item to [RAID].
4. Save your changes, and then exit the BIOS Setup.
Refer to Chapter 3 for details on entering and navigating through the BIOS Setup
Due to chipset limitation, when SATA ports are set to RAID mode, all SATA ports run at
RAID mode together.
5-2 Chapter 5: RAID configurations
5.1.4 Intel
®
Rapid Storage Technology Option ROM utility
To enter the Intel ® Rapid Storage Technology Option ROM utility:
1. Turn on the system.
2. During POST, press <Ctrl> + <I> to display the utility main menu.
Intel(R) Rapid Storage Technology - Option ROM - v10.5.1.1070
Copyright(C) 2003-10 Intel Corporation. All Rights Reserved.
[
1. Create RAID Volume
MAIN MENU ]
5. Acceleration Options
6. Exit
[ DISK/VOLUME INFORMATION ]
RAID Volumes:
None defined.
Physical Devices:
Port Device Model Serial # Size Type/Status(Vol ID)
0 ST3160812AS 9LS0HJA4 149.0GB
1 ST3160812AS 9LS0F4HL 149.0GB
2 ST3160812AS 3LS0JYL8 149.0GB
3 ST3160812AS 9LS0BJ5H 149.0GB
Non-RAID Disk
Non-RAID Disk
Non-RAID Disk
Non-RAID Disk
[↑↓]-Select
[ESC]-Exit [ENTER]-Select Menu
The navigation keys at the bottom of the screen allow you to move through the menus and select the menu options.
The RAID BIOS setup screens shown in this section are for reference only and may not exactly match the items on your screen.
The utility supports maximum four hard disk drives for RAID configuration.
ASUS Z97M-PLUS
5-3
5-4
Creating a RAID set
To create a RAID set:
1. From the utility main menu, select 1. Create RAID Volume and press <Enter>. The following screen appears:
Intel(R) Rapid Storage Technology - Option ROM - v10.5.1.1070
Copyright(C) 2003-10 Intel Corporation. All Rights Reserved.
[ CREATE VOLUME MENU ]
Name: Volume0
RAID Level:
Disks:
Strip Size:
Capacity:
Sync:
Create volume
[ HELP ]
[↑↓]-Select
[ESC]-Exit [ENTER]-Select Menu
2. Enter a name for the RAID set and press <Enter>.
3. When the RAID Level item is selected, press the up/down arrow key to select a RAID level to create, and then press <Enter>.
4. When the Disks item is selected, press <Enter> to select the hard disk drives you want to include in the RAID set. The SELECT DISKS screen appears:
[ SELECT DISKS ]
Port Drive Model Serial # Size Status
0 ST3160812AS 9LS0HJA4 149.0GB Non-RAID Disk
1 ST3160812AS 9LS0F4HL 149.0GB Non-RAID Disk
2 ST3160812AS 3LS0JYL8 149.0GB Non-RAID Disk
3 ST3160812AS 9LS0BJ5H 149.0GB Non-RAID Disk
Select 2 to 6 disks to use in creating the volume.
[↑↓]-Prev/Next [SPACE]-SelectDisk [ENTER]-Done
Chapter 5: RAID configurations
5. Use the up/down arrow key to select a drive, and then press <Space> to select. A small triangle marks the selected drive. Press <Enter> after completing your selection.
6. Use the up/down arrow key to select the stripe size for the RAID array (for RAID 0, 10 and 5 only),and then press <Enter>. The available stripe size values range from 4KB to 128KB. The following are typical values:
• RAID 0: 128KB
• RAID 10: 64KB
• RAID 5: 64KB
We recommend a lower stripe size for server systems, and a higher stripe size for multimedia computer systems used mainly for audio and video editing.
7. When the Capacity item is selected, enter the RAID volume capacity that you want and press <Enter>. The default value indicates the maximum allowed capacity.
8. When the Create Volume item is selected, press <Enter>. The following warning message appears:
WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST.
Are you sure you want to create this volume? (Y/N):
9. Press <Y> to create the RAID volume and return to the main menu, or <N> to go back to the CREATE VOLUME menu.
ASUS Z97M-PLUS
5-5
5-6
Deleting a RAID set
Be cautious when deleting a RAID set. You will lose all data on the hard disk drives when you delete a RAID set.
To delete a RAID set:
1. From the utility main menu, select 2. Delete RAID Volume and press <Enter>. The following screen appears:
[ DELETE VOLUME MENU ]
[ HELP ]
Deleting a volume will reset the disks to non-RAID.
WARNING:
ALL DISK DATA WILL BE DELETED.
(This does not apply to Recovery volumes)
[↑↓]-Select [ESC]-Previous Menu [DEL]-Delete Volume
2. Use the up/down arrow key to select the RAID set you want to delete, and then press
<Del>. The following warning message appears:
[ DELETE VOLUME VERIFICATION ]
ALL DATA IN THE VOLUME WILL BE LOST!
(This does not apply to Recovery volumes)
Are you sure you want to delete volume “Volume0”? (Y/N):
3. Press <Y> to delete the RAID set and return to the utility main menu, or press <N> to return to the DELETE VOLUME menu.
Chapter 5: RAID configurations
Exiting the Intel
®
Rapid Storage Technology Option ROM utility
To exit the utility:
1. From the utility main menu, select 5. Exit, and then press <Enter>. The following warning message appears:
[ CONFIRM EXIT ]
Are you sure you want to exit? (Y/N):
2. Press <Y> to exit or press <N> to return to the utility main menu.
5.2 Creating a RAID driver disk
A floppy disk with the RAID driver is required when installing a Windows
®
operating system on a hard disk drive that is included in a RAID set.
The motherboard does not provide a floppy drive connector. You have to use a USB floppy disk drive when creating a SATA RAID driver disk.
5.2.1 Creating a RAID driver disk without entering the OS
To create a RAID driver disk without entering the OS:
1. Boot your computer.
2. Press <Del> during POST to enter the BIOS setup utility.
3. Set the optical drive as the primary boot device.
4. Insert the support DVD into the optical drive.
5. Save changes and exit BIOS.
6. When the Make Disk menu appears, press <1> to create a RAID driver disk.
7. Insert a formatted floppy disk into the USB floppy disk drive, then press <Enter>.
8. Follow the succeeding screen instructions to complete the process.
ASUS Z97M-PLUS
5-7
5-8
5.2.2 Creating a RAID driver disk in Windows
®
To create a RAID driver disk in Windows ® :
1. Start Windows ® .
2. Plug the USB floppy disk drive and insert a floppy disk.
3. Place the motherboard support DVD into the optical drive.
4. Go to the AHCI/RAID Driver tab then click Intel AHCI/RAID Driver Path to open the
RAID driver folder.
5. Select 32bit or 64bit folder depending on your operating system. Copy the files of the selected folder to the root path of your USB floppy disk drive.
Write-protect the floppy disk to avoid a computer virus infection.
5.2.3 Installing the RAID driver during Windows
®
OS installation
To install the RAID driver for Windows ® 7:
1. During the OS installation, click Load Driver to allow you to select the installation media containing the RAID driver.
2. Insert the USB flash drive with RAID driver into the USB port or the support DVD into the optical drive, and then click Browse.
3. Click the name of the device you’ve inserted, go to Drivers > RAID, and then select the RAID driver for the corresponding OS version. Click OK.
4. Follow the succeeding screen instructions to complete the installation.
Before loading the RAID driver from a USB flash drive, you have to use another computer to copy the RAID driver from the support DVD to the USB flash drive.
To set up a Windows
®
UEFI operating system under RAID mode, ensure to load the UEFI driver for your optical drive.
Chapter 5: RAID configurations
Appendices
Appendices
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
IC: Canadian Compliance Statement
Complies with the Canadian ICES-003 Class B specifications. This device complies with RSS
210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations.
This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Cut appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.
Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
Cet appareil est conforme aux normes CNR exemptes de licence d’Industrie Canada. Le fonctionnement est soumis aux deux conditions suivantes :
(1) cet appareil ne doit pas provoquer d’interférences et
(2) cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un fonctionnement non souhaité de l’appareil.
ASUS Z97M-PLUS
A-1
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
VCCI: Japan Compliance Statement
VCCI Class B Statement
This is a Class B product based on the standard of the VCCI Council. If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.
KC: Korea Warning Statement
REACH
Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of
Chemicals) regulatory framework, we published the chemical substances in our products at
ASUS REACH website at http://csr.asus.com/english/REACH.htm.
DO NOT throw the motherboard in municipal waste. This product has been designed to enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin indicates that the product (electrical and electronic equipment) should not be placed in municipal waste. Check local regulations for disposal of electronic products.
A-2
DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol of the crossed out wheeled bin indicates that the battery should not be placed in municipal waste.
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components as well as the packaging materials. Please go to http://csr.asus.com/english/Takeback.htm for detailed recycling information in different regions.
Appendices
ASUS contact information
ASUSTeK COMPUTER INC.
Address
Telephone
Fax
Web site
15 Li-Te Road, Peitou, Taipei, Taiwan 11259
+886-2-2894-3447
+886-2-2890-7798 [email protected]
http://www.asus.com
Technical Support
Telephone
Fax
Online support
+86-21-3842-9911
+86-21-5866-8722 ext. 9101# http://support.asus.com/techserv/techserv.aspx
ASUS COMPUTER INTERNATIONAL (America)
Address
Telephone
Fax
Web site
800 Corporate Way, Fremont, CA 94539, USA
+1-510-739-3777
+1-510-608-4555 http://www.asus.com/us/
Technical Support
Support fax
General support
Online support
+1-812-284-0883
+1-812-282-2787 http://www.service.asus.com/
ASUS COMPUTER GmbH (Germany and Austria)
Address
Fax
Web site
Online contact
Harkort Str. 21-23, D-40880 Ratingen, Germany
+49-2102-959931 http://www.asus.com/de http://eu-rma.asus.com/sales
Technical Support
Telephone
Support Fax
Online support
+49-2102-5789555
+49-2102-959911 http://www.asus.com/de/support/
ASUS Z97M-PLUS
A-3
A-4
Suppl
Appendices
advertisement
Key Features
- Intel LGA 1150 (Socket H3) Intel® Celeron®, Intel® Pentium®
- PC micro ATX Intel® Z97 Realtek ALC887 7.1 channels
- DDR3-SDRAM 4 DIMM Non-ECC Maximum internal memory: 32 GB
- SATA III
- Quad-GPU CrossFireX 512
- BIOS type: UEFI AMI 64 Mbit ACPI version: 5.0 Clear CMOS jumper
- Gigabit Ethernet
Related manuals
advertisement