Backyard Discovery 2105324COM Rayven 14 ft. x 12 ft. Gazebo 用户指南

Owner’s Manual
Safety Warnings and Maintenance Instructions
WARNING
IT IS IMPORTANT TO CHECK AND TIGHTEN ALL HARDWARE AT THE BEGINNING AND DURING
THE SEASON AS THEY MAY LOOSEN DUE TO WOOD EXPANSION AND CONTRACTION.
DO NOT climb or walk on the roof for any reason
Requires two or more people to assemble safely
Check for underground utilities before digging or -
driving stakes into the ground.
Check carefully for overhead lines and ensure there is
at least 6ft (2m) clearance from any overhead electrical
wires.
Permanent structures may require a building permit.
As the purchaser and or installer of this product you are
advised to consult local planning, zoning and building :
inspection departments for guidance on applicable
building codes and/or zoning requirements.
Wood is NOT flame retardant and will burn. Grills, fire pits
and chimineas are a fire hazard if place too close to your
structure.
Wear gloves to avoid injury during installation.
During installation, follow all safety warnings provided
with your tools and use safety glasses.
Check all nuts and bolts twice monthly during the usage
season and tighten as required.(But not so tight that you
crack the wood) It is particularly important that this
procedure be followed at the beginning of each season.
Oil all metallic moving parts monthly during the usage
period.
Check all coverings for bolts and sharp edges twice
monthly during usage season to be certain they are in
place. Replace when necessary. It is especially important
to do this at the beginning of each new season.
For rusted areas on metallic members such as hinges,
brackets, etc. sand and repaint, using a non lead-based
paint meeting the requirements of Title 16 CRF Part 1303.
Inspect wood parts monthly. The grain of the wood
sometimes will lift in the dry season causing splinters to
appear. Light sanding may be necessary to maintain a
safe environment. Treating your Product with protection
(sealant) after sanding will help prevent severe checking/
splitting and other weather damage.
We have applied a waterborne translucent stain to your
unit. This is done for color only. Once or twice a year,
depending on your climate conditions, you must apply
some type of protection (sealant) to the wood of your unit.
Prior to the application of sealant, lightly sand any “rough”
spots on your set. Please note this is a requirement of
your warranty.
OWNERS SHALL BE RESPONSIBLE FOR MAINTAINING THE LEGIBILITY OF THE WARNING LABELS
nn
5
Instructions for Proper Maintenance
Owner’s Manual
Your Backyard Discovery structure is designed and constructed of quality
materials. As with all outdoor products it will weather and wear. To maximize
the enjoyment, safety and life of your structure it is important that you properly
maintain it.
About Our Wood
Backyard Discovery uses 100% Nordic Spruce wood. Although we take great care in
selecting the best quality lumber available, wood is still a product of nature and
susceptible to weathering which can change the appearance of your set.
What causes weathering? Does it affect
the strength of my product?
One of the main reasons for weathering is the
effects of water (moisture); the moisture content
of the wood at the surface is different than the
interior of the wood. As the climate changes,
moisture moves in or out of the wood, causing
tension which can result in checking and or
warping. You can expect the following due to
weathering. These changes will not affect the
strength of the product:
1. Checking is surface cracks in the wood along
the grain. А post (4”x 4”) will experience more
checking than a board (1”х 4”) because the surface
and interior moisture content will vary more widely
than in thinner wood.
2. Warping results from any distortion (twisting,
cupping) from the original plane of the board and
often happens from rapid wetting and drying of
the wood.
3. Fading happens as a natural change in the
wood color as it is exposed to sun-light and will
turn grey over time.
How can | reduce the amount of
weathering to wood product?
1. Your wood product is coated with a
water-based stain. Sunlight will break down
the coating, so we recommend applying
a water repellent or stain on a yearly basis
(see your local stain and paint supplier for a
recommended product). You must apply some
type of protection (sealant) to the wood of your
product. Please note this is a requirement
of your warranty. Most weathering is just
the normal result of nature and will not affect
safety. However if you are concerned that a part
has experienced a severe weathering problem
please call our customer service department for
further assistance.
2. Inspect wood parts monthly. The grain of
the wood sometimes will lift in the dry season
causing splinters to appear. Light sanding may
be necessary to maintain a safe environment.
Treating your Product with protection (sealant)
after sanding will help prevent severe checking/
splitting and other weather damage.
Owner's Manual
Protrusion Hazard
Incorrect Correct
If you see exposed
threads and your bolt
protrudes beyond the
T-Nut you may have over
ZA tightened the bolt or
[ae À used incorrect hardware.
ae If you've overtightened,
remove the bolt and add
washers to eliminate the
protrusion.
> SSA
Proper Hardware Assembly
Bolt and T-Nut Assembly
Tap T-nut into the provided hole. Insert your bolt through
the lock washer and insert into the provided hole opposite
from the T-Nut. Turn clockwise to thread into T-nut. Do not
completely tighten until instructed. o” al
LOCK WASHER
Bolt and Barrel Nut Assembly ee |
Insert barrel nut through the lock washer and press the pair i
through the provided hole. Insert your bolt through the
second lock washer and insert the pair into the provided hole
opposite from the barrel nut. Turn clockwise to thread into the De: |
barrel nut. Do not completely tighten until instructed. N
> | ВАВВЕЕ МОТ
LOCK WASHER
LOCK WASHER
Lag Assembly TLAG SCREW
Normally there will be a pre-drilled pilot hole on assemblies
that require a Lag Screw. If there is no pilot hole, line up the
two boards as they are to be attached and use the factory
drilled hole as a guide to drill another pilot hole into the
adjoining board. This will keep the wood from splitting. Only a
lock washer is required for steps with Lag Screws.
YY ASSEMBLY TIP:
= Keep and eye out for these boxes which will contain helpful pictures and information making
the assembly process as quick and painless as possible.
Sorting Wood
When removing the wood from the boxes we recommend arranging them by part number before you begin
assembly. This will allow for faster assembly and easily identify any parts that may be missing or damaged.
Sorting Hardware
NUT BARREL SCREW T-NUT WASHER FLAT BOLT HEX BOLT SCREW PWH
H100545 H100695 H100699 H100706 H100716 H100718 H100742
To help with assembly we recommend sorting your hardware bags with the seven digit alpha-numeric number
printed on the bags or by hardware type (i.e. bolts, nuts, etc.). Organizing your hardware will make assembly easier.
г a
Hardware bags are printed with |
a seven digit alpha-numeric part
number. During assembly you only | AN
the correct hardware easier. 37800)
need to reference the last three 19262)
digits of the part number as noted _ JH100378 | BOLT WH 199(x2)
in each step. This will make finding (x2) | 5/16x1-3/4
198(x2)
You will need to make sure that your
assembly is square before tightening
your bolts.
For proper assembly you will need to
ensure that your structure is level before
proceeding to the next step.
Some steps in the assembly process will
require an extra set of hands. Make sure
you have a helper available.
This icon shows the size of an open
ended wrench. Using the wrench as the
fraction bar.
où
When you see this icon you will need
a socket wrench. The icons below show
the size of attachments needed for
assembly 1/2.
This icon warns you to not over tighten
your bolts. This is to prevent structural
damage and also splintering your wood.
A ladder will be needed for assembly.
Do NOT stand on the set when it is
incomplete, unstable, and not anchored.
Failure to do so may result in injury.
This icon will show you what drill
attachments are needed. For this
example you will need a Phillips head
attachment and 3/8 drill bit.
Owner's Manual Basic Setup Dimensions & Assembly Notes
It is critically important that you start with square and level footings, concrete pad or deck to
attach your structure
e Pay close attention to the items needed for each step. Make sure you are using the correct hardware for each step.
Using incorrect hardware may result in improper assembly
e Remember to double check for underground utilities and overhead electrical lines
Post mounts are provided with your structure which allows you to permanently install your structure to a
pre-existing or new wood or concrete surface.
e The hardware to attach the post mounts to the structure is included.
e The hardware to mount the structure permanently to a concrete surface is included.
e The hardware to mount the structure permanently to a wood deck is NOT included and will need to be purchased
separately. You must ensure there is ample structural support under the deck before permanently attaching.
IMEC
N
10.2 ft
13.5 ft [3.1 m] 10.8 ft
[4.11 m] [3.28 m] 7.2 ft
[2.2 m]
| 12.5 ft | o 12.98 mi
FE [3.81 m] Eh Y El Bi
14.4 ft
[4.4 m]
A 12.1 tt
Т|| [3.69 m]
10