WarmlyYours

TempZone

™

Easy Mats

TempZone™ Easy Mats allow for radiant heating of smaller, simpler areas at an affordable cost. Install radiant heating mats in front of your kitchen appliances and bath fixtures for a warm path of under floor heat where you stand the most.

We call this type of application “spot-heating” and it’s a very affordable option for incorporating floor heating into a smaller room like a bathroom. Utilizing the TempZone™ technology, Easy Mats are available in 120 volt systems. These under floor mats are perfect for providing targeted heating for moderately sized bathroom and kitchen floors or just the high traffic cooking areas of larger kitchens.

Installs under:

Tile Stone

Product Information

Easy Mat

Heating wire attached to an open cell type fiberglass mesh

Heating Element

Color

Heating Element

Insulation

Heating Cable

Outer Insulation

Blue

Fluoropolymer

Fluoropolymer

Heating Output 15 watts per sq. ft.

Certifications

UL listed for wet locations like shower floors and benches

Warranty

Example Project

25-year No Nonsense™ Warranty

Heated Area

Product Cost

3’ x 6’

$234.00 USD

$292.50 CAD

Bathroom

3’ x 8’

$276.00 USD

$345.00 CAD

3’ x 10’

$300.00 USD

$375.00 CAD

Hourly Cost*

1¢/hr USD

2¢/hr CAD

2¢/hr USD

2¢/hr CAD

2¢/hr USD

3¢/hr CAD

* Based on national average of 12¢ per kWh (USA) and 14¢ per kWh (Canada)

Engineered Wood &

Laminate

Dimensions

Heating Element

Thickness

Cold Lead

Information

LVT

Variable, nominal 1/8”

•

Length: 15’

•

17 AWG for mats of

9 amps or less

•

1/2” Conduit

2 Cold Leads Max

•

3/4” Conduit - 3 Cold Leads

Install per local code requirements

Factory Splice

Max Size

.4”, 13/32”, 10.3mm

Electrical

TempZone Easy Mats have no polarity.

WarmlyYours controls are equipped with ground fault circuit interrupter (G.F.C.I.) protection.

Voltage

Cold Lead

Construction

Cold Lead

Wire Colors

Available in 120V

Style number AWM2095, 2 core wires, screened with ground

120V: Yellow & black with black outer sheath

4 Simple Steps to Install

1

Layout TempZone™ Easy

Mats according to your custom SmartPlan™

2

Secure the Included

Floor Sensor

Installation Information

•

Heating element should be embedded within a

minimum 3/8” thick layer of modified thinset or self-

leveling underlayment.

•

Heating element should be installed within 1” to 1.5”

from the top of the flooring surface.

•

Multiple Easy Mats can be wired to a control, as

long as they total less than 15 amps (the limit of the

controller).

•

Multiple Easy Mats are never wired to each other in

series (parallel wiring required). The non-heating

leads from each Easy Mat need to hook up to the

controller and be wired in parallel.

•

Do not install under permanent fixtures.

•

Do not install within 4” of the toilet wax ring.

•

Entire heating section and splices need to be

embedded in thinset or self-leveling underlayment

to prevent overheating and premature failure.

•

Do not shorten the warming mat. Do NOT cut the

heating wire. Only the non-heating cold leads can

be shortened.

•

Do not run a power lead or sensor wire across a

warming cable.

3

Apply Thinset or SLC (3/5” thick minimum)

4

Install

Flooring

•

Do not fold or position the warming system so that the

mesh overlaps itself or other warming cables (this could

lead to dangerous overheating).

•

Do not connect the warming mat to the power supply for

testing before it is embedded (this could lead to

dangerous overheating). Testing is only done with a

digital ohm meter.

•

120 sq. ft. of heating can be installed on a single 120 V

circuit.

•

TempZone Easy Mats should be installed with a floor

sensor. All WarmlyYours nSpiration Series thermostats

come with a floor sensor.

How to Order

1 Simply draw a floor plan sketch of your project

(including dimensions) .

2 Send it to [email protected]

. Then

WarmlyYours’s skilled engineers will create a free

SmartPlan™ custom installation plan based on your drawing, typically in as little as 1 business day.

3 After you receive your SmartPlan™, just verify the correct dimensions before placing your order with your WarmlyYours account manager.

Draw a floor plan of your project and we’ll do the rest!